TC4W66F/FU TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC4W66F,TC4W66FU Dual Bilateral Switch The TC4W66 contains two independence circuits of bidirectional switches. When control input CONT is set to "H" level, the impedance between input and output of the switch becomes low and when it is set to "L" level, the switch becomes high. This can be applied for switching of analog signals and digital signals. TC4W66F Features * ON-resistance, RON 250 (typ.) ................... VDD - VSS = 5 V TC4W66FU 110 (typ.) ................... VDD - VSS = 10 V 70 (typ.)..................... VDD - VSS = 15 V * OFF-resistance, ROFF ROFF (typ.) > 109 Weight SOP8-P-1.27: 0.05 g (typ.) SSOP8-P-0.65: 0.02 g (typ.) Absolute Maximum Ratings Symbol Rating Unit DC supply voltage Characteristics VDD VSS - 0.5 to VSS + 20 V Control input voltage VC IN VSS - 0.5 to VDD + 0.5 V Switch I/O voltage VI/O VSS - 0.5 to VDD + 0.5 V Power dissipation PD 300 mW Potential difference across I/O during ON VI-VO 0.5 V Control input current IC IN 10 mA Operating temperature range Topr -40 to 85 C Storage temperature Tstg -65 to 150 C Lead temp./time TL 260C/10 s Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Marking TC4W66F TC4W66FU 1 2007-11-01 TC4W66F/FU Logic Diagram Pin Assignment (top view) (1/2 TC4W66F) Truth Table Control Impedance Between IN/OUT-OUT/IN (Note 1) 2 H 0.5 to 5 x 10 L >10 9 Note 1: See static electrical characteristics. Operating Ranges (VSS = 0 V) Characteristics DC supply voltage Input/output voltage Symbol Test Condition Min Typ. Max Unit VDD 3 18 V VDD/VOUT 0 VDD V Static Electrical Characteristics (in case not specifically appointed, VSS = 0 V) Characteristics Control input high voltage Control input low voltage On-state resistance VIH VIL RON On-state resistance (between any 2 switches) Input/output leakage current Quiescent device current Input current Symbol H level L level RON IOFF IDD IIH IIL Test Test Condition V Circuit DD (V) IIS = 10 A IIS = 10 A 0< = VIS < = VDD RL = 10 k Ta = -40C Ta = 25C Ta = 85C Min Max Min Typ. Max Min Max 5 3.5 3.5 2.75 3.5 10 7.0 7.0 5.50 7.0 15 11.0 11.0 8.25 11.0 5 1.5 2.25 1.5 1.5 10 3.0 4.5 3.0 3.0 15 4.0 6.75 4.0 4.0 5 800 290 950 1200 10 210 120 250 300 15 140 85 160 200 5 10 10 6 15 4 VIN = 18 V, VOUT = 0 V 18 100 0.1 100 1000 VIN = 0 V, VOUT = 18 V 18 100 0.1 100 1000 5 0.25 0.001 0.25 7.5 10 0.5 0.001 0.5 15 15 1.0 0.002 1.0 30 0.1 1.0 -0.1 -1.0 VIN = VDD, VSS* VIH = 18 V VIL = 0 V Unit V V nA 18 18 2 0.1 -0.1 10 -5 -10 -5 A A 2007-11-01 TC4W66F/FU Dynamic Electrical Characteristics (Ta = 25C, VSS = 0 V, CL = 50 pF) Characteristics Phase difference between input to output Propagation delay time (CONTROL-OUT) Propagation delay time (CONTROL-OUT) Max control input repetition Rate -3dB cutoff frequency Symbol I-O tpZL tpZH tpLZ tpHZ fmax (C) fmax (I-O) Test Circuit Total harmonic distortion -50dB feed through frequency -50dB crosstalk frequency Crosstalk (CONTROL-OUT) Input capacitance Feed through capacitance CIN CIN-OUT Test Condition CL = 50 pF RL = 1 k CL = 50 pF RL = 1 k CL = 50 pF RL = 1 k CL = 50 pF RL = 1 k CL = 50 pF (Note 1) RL = 10 k VSS (V) VDD (V) Min Typ. Max Unit 0 5 15 40 0 10 8 20 0 15 5 15 0 5 55 120 0 10 25 40 0 15 20 30 0 5 45 80 0 10 30 70 0 15 25 60 0 5 10 0 10 12 0 15 12 -5 5 30 MHz -5 5 0.03 % ns ns ns MHz f = 1 kHz (Note 2) RL = 1 k (Note 3) -5 5 600 kHz RL = 1 k (Note 4) -5 5 1 MHz RIN = 1 k 0 5 200 ROUT = 10 k 0 10 400 CL = 15 pF 0 15 600 Control input 5 7.5 Switch I/O 10 0.5 Note 1: Since wave of 2.5 Vp-p shall be used for VIS and the frequency of 20 og 10 mV pF pF VOS = -3dB shall be fmax. VIS Note 2: VIS shall be sine wave of 2.5 Vp-p. Note 3: Sine wave of 2.5 Vp-p shall be used for VIS and the frequency of 20 og 10 VOUT VIS = -50dB shall be VOUT VIS = -50dB shall be feed-through. Note 4: Sine wave of 2.5 Vp-p shall be used for VIS and the frequency of 20 og 10 crosstalk. 3 2007-11-01 TC4W66F/FU 1. tpLH, tpHL I/O-O/I 2. tpZL, tpZH, tpLZ, tpHZ Control-O/I 3. RON 4. fmax (C) 4 2007-11-01 TC4W66F/FU 5. Crosstalk (switch I/O) 6. Crosstalk (control input) 7. Total Harmonic Distortion, fmax (I/O-O/I), Feedthrough (switch OFF) 2.5 V I/O IN. 0V -2.5 V 1 f 5 2007-11-01 TC4W66F/FU Package Dimensions Weight: 0.05 g (typ.) 6 2007-11-01 TC4W66F/FU Package Dimensions Weight: 0.02 g (typ.) 7 2007-11-01 TC4W66F/FU RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 8 2007-11-01