SOT-23 SURFACE MOUNT LED LAMP ATTENTION Part Number: AM23SRD-F Super Bright Red OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z SOT-23 package surface mount LED lamp. z The Super Bright Red source color devices are made with Gallium Aluminum Arsenide Red Light Emitting z Low power consumption. z Long life - solid state reliability. Diode. z Electrostatic discharge and power surge could damage z Package: 2000pcs / reel. z Moisture sensitivity level : level 3. the LEDs. z It is recommended to use a wrist band or anti- z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the lead emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 5.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAB4313 REV NO: V.8A DATE: FEB/20/2017 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1202000080 Selection Guide Part No. Emitting Color (Material) Lens Type Super Bright Red (GaAlAs) AM23SRD-F Red Diffused Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 55 90 *12 *30 21/2 170 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Emitting Color Typ. peak Peak Wavelength Super Bright Red D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 655 nm IF=20mA Super Bright Red 640 nm IF=20mA Spectral Line Half-width Super Bright Red 20 nm IF=20mA C Capacitance Super Bright Red 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Super Bright Red 1.85 2.5 V IF=20mA IR Reverse Current Super Bright Red 10 uA VR = 5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter Values Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 155 mA 5 V Reverse Voltage Operating Temperature -40C To +85C Storage Temperature -40C To +85C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAB4313 REV NO: V.8A DATE: FEB/20/2017 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1202000080 Red Relative Intensity (a. u.) 100% 80% Ta = 25 C 60% 40% 20% 0% 350 Super Bright Red 400 450 500 550 600 Wavelength (nm) 650 700 750 800 AM23SRD-F Ta = 25 C -15 0 15 30 -30 45 -45 60 -60 75 -75 -90 1.0 0.5 0.0 0.5 90 1.0 SPEC NO: DSAB4313 REV NO: V.8A DATE: FEB/20/2017 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1202000080 AM23SRD-F Recommended Soldering Pattern (Units : mm; Tolerance: 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAB4313 REV NO: V.8A DATE: FEB/20/2017 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1202000080 PACKING & LABEL SPECIFICATIONS AM23SRD-F Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAB4313 REV NO: V.8A DATE: FEB/20/2017 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1202000080