Data Sheet: JN5148-001-Myy JenNet, ZigBee PRO and IEEE802.15.4 Module Overview The JN5148-001-Myy family is a range of ultra low power, high performance surface mount modules targeted at JenNet and ZigBee PRO networking applications, enabling users to realise products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites. The modules use Jennic's JN5148 wireless microcontroller to provide a comprehensive solution with large memory, high CPU and radio performance and all RF components included. All that is required to develop and manufacture wireless control or sensing products is to connect a power supply and peripherals such as switches, actuators and sensors, considerably simplifying product development. Three module variants are available: JN5148-001-M00 with an integrated antenna, JN5148-001-M03 with an antenna connector and the JN5148-001-M04 with an antenna connector, power amplifier and LNA for extended range. The modules can implement networking stacks such as JenNet and ZigBee PRO, as well as customer applications Features: Module * 2.4GHz IEEE802.15.4, JenNet and ZigBee PRO compatible * Sleep current (with active sleep timer) 2.6A * * 512kB Serial Flash Memory XTAL JN5148 chip Time of Flight Engine Matching RAM 128kB ROM 128kB M00 Option O-QPSK Modem Matching M03 Option External Antenna uFl Connector Watchdog timer PA / LNA Matching M04 Option Power Management SPI 2-wire serial 2.4GHz Radio uFl Connector JN5148-001-M04 up to 4km range (Ext Antenna) o 20dBm TX power o Receiver sensitivity -98dBm o uFl connector o TX current 110mA o RX current 23mA o 18x41mm o 2.7-3.6V operation Module Block Diagram Integrated Antenna JN5148-001-M00/03 up to 1km range (Ext antenna) M00: integral antenna 18x32mm M03: uFl connector 18x30mm o TX power +2.5dBm o Receiver sensitivity -95dBm o TX current 15mA o RX current 17.5mA o 2.3-3.6V operation IEEE802.15.4 MAC Accelerator RISC CPU 32-byte OTP eFuse Timers Features: Microcontroller UARTs * 32-bit RISC CPU, up to 32MIPs with low power * 128kB ROM stores system code * 128kB RAM stores system data and bootloaded program code * 4Mbit serial flash for program code and data * On chip OTP efuse * JTAG debug interface * 4-input 12-bit ADC, 2 12-bit DACs, 2 comparators * 3 application timer/counters, 3 system timers 4-Wire Audio Sleep Counters 12-bit ADC, comparators 128-bit AES Encryption Accelerator 12-bit DACs, temp sensor Power Benefits Applications * Microminiature module solutions * * Ready to use in products Robust and secure low power wireless applications * Minimises product development time * ZigBee PRO and JenNet networks * * 2 UARTs Home and commercial building automation * SPI port with 5 selects * * 2-wire serial interface Utilities metering (e.g. AMR) * * 4-wire digital audio interface Location Aware services (e.g. Asset Tracking) * Watchdog timer * Up to 21 DIO * No RF test required for systems * Compliant with FCC part 15 rules, IC Canada RSS 210e, ETSI EN 300-328 and Japan ARIB STD-T66 * Toys and gaming peripherals * Industrial systems * * Telemetry Remote Control JN-DS-JN5148-001-Myy 1v4 Industrial temp (-40C to +85C) Lead-free and RoHS compliant (c) NXP Laboratories UK 2010 Contents 1. Introduction 3 1.1. 1.2. 3 3 Variants Regulatory Approvals 2. Specifications 4 3. Product Development 5 3.1. 5 JN5148 Single Chip Wireless Microcontroller 4. Pin Configurations 6 4.1. 4.2. 4.2.1 4.2.2 7 8 8 8 Pin Assignment Pin Descriptions Power Supplies SPI Memory Connections 5. Electrical Characteristics 9 5.1. 5.2. 9 9 Maximum Ratings Operating Conditions Appendix A Additional Information A.1 Outline Drawing A.2 Module PCB Footprint A.3 Manufacturing A.3.1 Reflow Profile A.3.2 Soldering Paste and Cleaning A.4 Ordering Information A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions A.5.2 Cover tape details A.5.3 Leader and Trailer A.5.4 Reel Dimensions: A.6 Related Documents A.7 Federal Communication Commission Interference Statement A.7.1 Antennas approved by FCC for use with JN5148 modules A.7.2 High Power Module usage limitation A.7.3 High Power Module channel restriction A.7.4 FCC End Product Labelling A.8 Industry Canada Statement A.8.1 Industry Canada End Product Labelling A.9 European R & TTE Directive 1999/5/EC Statement A.10 RoHS Compliance A.11 Status Information A.12 Disclaimers Version Control ii JN-DS-JN5148-001-Myy 1v4 10 10 13 14 14 14 15 16 16 16 17 17 17 18 19 20 20 20 20 20 21 22 22 22 23 (c) NXP Laboratories UK 2010 1. Introduction The JN5148-001-Myy module family provides designers with a ready made component that provides a fully integrated solution for applications, using the IEEE802.15.4 standard in the 2.4-2.5GHz ISM frequency band [1], including JenNet and ZigBee PRO, and can be quickly and easily included in product designs. The modules integrate all of the RF components required, removing the need to perform expensive RF design and test. Products can be designed by simply connecting sensors and switches to the module IO pins. The modules use Jennic's single chip IEEE802.15.4 Wireless Microcontroller, allowing designers to make use of the extensive chip development support material. Hence, this range of modules allows designers to bring wireless applications to market in the minimum time with significantly reduced development effort and cost. Three variants are available: JN5148-001-M00 (standard module with integral antenna), JN5148-001-M03 (standard module with uFl connector for use with external antennae) and JN5148-001-M04 (high RF power with uFL connector, improved sensitivity module for evaluation of extended range applications). All modules have FCC modular approvals and are compliant with EU regulations. The variants available are described below. 1.1. Variants Variant Description FCCID Industry Canada ID JN5148-001-M00 Standard Power, integrated antenna TYOJN5148M0 IC: 7438A-CYO5148M0 JN5148-001-M03 Standard Power, uFl connector TYOJN5148M3 IC: 7438A-CYO5148M3 JN5148-001-M04 High Power, uFl connector TYOJN5148M4 IC: 7438A-CYO5148M4 1.2. Regulatory Approvals All module types have been tested against the requirements of European standard ETS 300 328 v1.7.1 and a Notified Body statement of opinion for this standard is available on request. The High Power module with M04 suffix is approved for use in Europe with reduced output power: +10dBm EIRP is the maximum permitted in Europe. Additionally, all module types have received FCC "Modular Approvals", in compliance with CFR 47 FCC part 15 regulations and in accordance to FCC Public notice DA00-1407, appendix A.7 contains details on the conditions applying to this modular approval. The modules are approved for use with a range of different antennas; further details of which can be found in section Appendix A.6.1. The modular approvals notice and test reports are available on request. The high power module variant is classified as `mobile' device pursuant with FCC 2.1091 and must not be used at a distance of less than 20 cm (8") from any person. In addition, all modules have Industry Canada modular approval and RSS210e Issue 7 (June 2007) certification. (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 3 2. Specifications Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5148 Wireless Microcontroller Datasheet, [2]. Where there are differences, the parameters are defined here. VDD=3.0V @ +25C Typical DC Characteristics Notes JN5148-001M00/03 JN5148-001M04 Deep sleep current 1.3uA 1.3uA Sleep current 2.6uA 2.6uA With active sleep timer Radio transmit current 15mA 110mA CPU in doze, radio transmitting Radio receive current 17.5mA 23mA CPU in doze, radio receiving +/-25ppm +/-25ppm Centre frequency accuracy Additional +/-15ppm allowance for temperature and ageing Typical RF Characteristics Notes Receive sensitivity -95dBm -98dBm Nominal for 1% PER, as per 802.15.4 section 6.5.3.3 (Note 1) Maximum Transmit power +2.5dBm 18dBm Nominal (Note 1) 20dBm With Vdd=3.6V +5dBm -5dBm For 1% PER, measured as sensitivity -95 to -10 dBm -105 to -20 dBm 50 ohm 50 ohm 2.4 - 2.5GHz 2:1 2:1 2.4 - 2.5GHz Transmit power at 3.6V Maximum input signal RSSI range RF Port impedance - uFl connector VSWR (max) Peripherals Notes Master SPI port 5 selects 3 selects 250kHz - 16MHz Slave SPI port 9 9 250kHz - 8MHz 9 9 16550 compatible Two-wire serial I/F (compatible with SMbus & I C) 9 9 Up to 400kHz Two programmable Timer/Counters with capture/compare facility, Tick timer 9 9 16MHz clock Two programmable Sleep Timers 9 9 32kHz clock Digital IO lines (multiplexed with UARTs, timers and SPI selects) 21 19 Four channel Analogue-to-Digital converter 9 9 12-bit, up to 100ks/s Two channel Digital-to-Analogue converter 9 9 12-bit, up to 100ks/s Two programmable analogue comparators 9 9 Ultra low power mode for sleep Internal temperature sensor and battery monitor 9 9 Two UARTs 2 The performance of all peripherals is defined in the JN-DS-JN5148 Wireless Microcontroller Datasheet [2] Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity. 4 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 3. Product Development Jennic supplies all the development tools and networking stacks needed to enable end-product development to occur quickly and efficiently. These are all freely available from www.nxp.com/jennic. A range of evaluation/developer kits is also available, allowing products to be quickly bread boarded. Efficient development of software applications is enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the IEEE802.15.4 MAC and the JenNet and ZigBee PRO network stacks, this package provides everything required to develop application code and to trial it with hardware representative of the final module. The modules can be user programmed both in development and in production using software supplied by Jennic. Access to the on-chip peripherals, MAC and network stack software is provided through specific APIs. This information is available on the Jennic support website, together with many example applications, user guides, reference manuals and application notes. 3.1. JN5148 Single Chip Wireless Microcontroller The JN5148-001-Myy series is constructed around the JN5148-001 single chip wireless microcontroller, which includes the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital peripherals. The chip is described fully in JN-DS-JN5148 Wireless Microcontroller Datasheet [2]. The module also includes a 4Mbit serial flash memory, which holds the application code that is loaded into the JN5148 during the boot sequence and provides static data storage, required by the application. (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 5 4. Pin Configurations ADC4 DAC1 1 41 2 40 DAC2 COMP2+ COMP2SPICLK SPIMISO SPIMOSI SPISSZ DIO0 3 39 DIO1 DIO2 SPISSM SPISWP DIO3 ADC3 ADC2 10 ADC1 38 COMP1+ 37 COMP136 DIO20 35 DIO19 34 DIO18 33 DIO17 32 DIO16 11 31 12 30 13 29 14 28 15 27 4 5 6 7 8 9 DIO15 DIO14 RESETN DIO13 DIO12 VDD GND VSSA DIO10 DIO11 DIO4 DIO5 DIO6 DIO7 DIO8 DIO9 16 17 18 19 20 21 22 23 24 25 26 Figure 1: Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3 and DIO2 are not available on the high power modules. 6 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 4.1. Pin Assignment Pin No Pin Functions Primary Alternate Functions Signal Type Description 1 ADC4 3.3V Analogue to Digital Input 2 DAC1 3.3V DAC Output 3 DAC2 3.3V DAC Output 4 COMP2+ 3.3V Comparator 2 Input +ve 5 COMP2- 3.3V Comparator 2 Input -ve 6 SPICLK CMOS SPI Clock Output 7 SPIMISO CMOS SPI Master In Slave Out Input 8 SPIMOSI CMOS SPI Master Out Slave In Output 9 SPISSZ CMSO SPI Select From Module - SS0 Output 10 DIO0 SPISEL1 CMOS DIO0 or SPI Slave Select Output 1 11 DIO1 SPISEL2 PC0 CMOS DIO1, SPI Slave Select Output 2 or Pulse Counter0 Input 12 DIO2* SPISEL3 RFRX CMOS DIO2, SPI Slave Select Output 3 or Radio Receive Control Output 13 SPISSM CMOS SPI Select to FLASH (Input) 14 SPISWP CMOS FLASH Write Protect (Input) 15 DIO3* SPISEL4 RFTX CMOS DIO3, SPI Slave Select Output 4 or Radio Transmit Control Output 16 DIO4 CTS0 JTAG_TCK CMOS DIO4, UART 0 Clear To Send Input or JTAG CLK 17 DIO5 RTS0 JTAG_TMS CMOS DIO5, UART 0 Request To Send Output or JTAG Mode Select 18 DIO6 TXD0 JTAG_TDO CMOS DIO6, UART 0 Transmit Data Output or JTAG Data Output 19 DIO7 RXD0 JTAG_TDI CMOS DIO7, UART 0 Receive Data Input or JTAG Data Input 20 DIO8 TIM0CK_GT PC1 CMOS DIO8, Timer0 Clock/Gate Input or Pulse Counter1 Input 21 DIO9 TIM0CAP 32KXTALIN CMOS DIO9, Timer0 Capture Input, 32K External Crystal Input or 32K Clock Input 22 DIO10 TIM0OUT 32KXTALOUT CMOS DIO10, Timer0 PWM Output or 32K External Crystal Output 23 DIO11 TIM1CK_GT TIM2OUT CMOS DIO11, Timer1 Clock/Gate Input or Timer2 PWM Output 32KIN 24 VDD 3.3V 25 GND 0V Digital Ground 26 VSSA 0V Analogue Ground 27 DIO12 TIM1CAP ADO DAI_WS CMOS DIO12, Timer1 Capture Input, Antenna Diversity or Digital Audio Word Select 28 DIO13 TIM1OUT ADE DAI_SDIN CMOS DIO13, Timer1 PWM Output, Antenna Diversity or Digital Audio Data Input 29 RESETN CMOS Reset input 30 DIO14 SIF_CLK IP_CLK CMOS DIO14, Serial Interface Clock or Intelligent Peripheral Clock Input 31 DIO15 SIF_D IP_DO CMOS DIO15, Serial Interface Data or Intelligent Peripheral Data Out 32 DIO16 IP_DI CMOS DIO16, Intelligent Peripheral Data In (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 Supply Voltage 7 33 DIO17 CTS1 IP_SEL DAI_SCK JTAG_TCK CMOS DIO17, UART 1 Clear To Send Input, Intelligent Peripheral Device Select Input or Digital Audio Clock or JTAG CLK 34 DIO18 RTS1 IP_INT DAI_SDOUT JTAG_TMS CMOS DIO18, UART 1 Request To Send Output, Intelligent Peripheral Interrupt Output or Digital Audio Data Output or JTAG Mode Select 35 DIO19 TXD1 JTAG_TDO CMOS DIO19 or UART 1 Transmit Data Output or JTAG Data Out 36 DIO 20 RXD1 JTAG_TDI CMOS DIO 20, UART 1 Receive Data Input or JTAG data In 37 COMP1- 3.3V Comparator 1 Input -ve 38 COMP1+ 3.3V Comparator 1 Input +ve 39 ADC1 3.3V Analogue to Digital Input 40 ADC2 3.3V Analogue to Digital Input 41 ADC3 3.3V Analogue to Digital Input *: These two pins are not connected for High power modules 4.2. Pin Descriptions All pins behave as described in the JN-DS-JN5148 Wireless Microcontroller Datasheet [2], with the exception of the following: 4.2.1 Power Supplies A single power supply pin, VDD is provided. Separate analogue (VSSA) and digital (GND) grounds are provided. These should be connected together at the module pins. 4.2.2 SPI Memory Connections SPISWP is a write protect pin for the serial flash memory. This should be held low to inhibit writes to the flash device. SPISSZ is connected to SPI Slave Select 0 on the JN5148. SPISSM is connected to the Slave Select pin on the memory. This configuration allows the flash memory device to be programmed using an external SPI programmer if required. For programming in this mode, the JN5148 should be held in reset by taking RESETN low. Two potential flash 4Mbit memory devices may be used in the module, the Numonyx M25P40 and the SST SST25VF040B. The memory can also be programmed over the UART by using the flash programmer software provided by Jennic. This is available as part of the Software Developer kit and libraries available from www.nxp.com/jennic. To enter this programming mode, SPIMISO (pin 7) should be held low whilst the chip is reset. Once programming has finished, the chip should be reset, when it will execute the new code downloaded. For normal operation of the module and programming over the UART, SPISSZ should be connected to SPISSM. 8 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 5. Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below. 5.1. Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Min Max Device supply voltage VDD -0.3V 3.6V Voltage on analogue pins VREF, ADC1-4, DAC1-2, COMP1M, COMP1P, COMP2M, COMP2P, IBIAS -0.3V VDD + 0.3V Voltage on 5v tolerant digital pins DIO0-DIO8 & DIO11-20, RESETN -0.3V Lower of (VDD + 2V) and 5.5V Voltage on 3v tolerant digital pins DIO9, DIO10, SPISSM, SPISWP, SPICLK, SPIMOSI, SPIMISO, SPISSZ -0.3V VDD + 0.3V Storage temperature -40C 150C 5.2. Operating Conditions Supply Min Max VDD (Module M00/M03) 2.3V 3.6V VDD (Module M04) 2.7V 3.6V Ambient temperature range -40C 85C (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 9 Appendix A Additional Information A.1 Outline Drawing 18mm 32.2mm 1.27 mm 2.54 mm 2.76 mm 2.54 mm Thickness: 3.5mm Figure 2 JN5148-001-M00 Outline Drawing 10 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 18mm 9.76mm 6.58 mm 30mm 1.27 mm 2.54 mm 2.54 mm 2.76 mm Thickness: 3.5mm Figure 3 JN5148-001-M03 Outline Drawing (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 11 18mm 7.2mm 4.05mm 40.5mm 1.27 mm 2.54 mm . 2.54 mm 2.76 mm Thickness: 3.5mm Figure 4 JN5148-001-M04 Outline Drawing 12 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 A.2 Module PCB Footprint All dimensions are in mm. Note: All modules have the same footprint. Figure 5 Module PCB footprint RF note for -M00 modules with integral antenna: No components, ground plane or tracks on any layer of the mother board should be placed within 20mm of the 3 free sides of the antenna. Tracks etc may be placed adjacent to the can, but should not extend past the can towards the antenna end of the module for 20mm from the antenna. (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 13 A.3 Manufacturing A.3.1 Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in figure 6 as a guide, as well as the paste manufacturers guidelines on peak flow temperature, soak times, time above liquidus and ramp rates. Temperature Target Time (s) 25~160 C 160~190 C > 220 C 230~Pk. Pk. Temp (235C) 90~130 30~60 20~50 10~15 150~270 Figure 6: Recommended solder reflow profile A.3.2 Soldering Paste and Cleaning Jennic would not recommend use of a solder paste that requires the module and pcb assembly to be cleaned (rinsed in water) for the following reasons: Solder flux residues and water can be trapped by the pcb, can or components and result in short circuits. The module label could be damaged or removed. Jennic recommends use of a 'no clean' solder paste for all its module products. 14 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 A.4 Ordering Information Ordering Code Format: JN5148 - 001 - M / Y1Y2 Y3 Shipping T Tape Mounted 500-piece reel Module Type 00 Standard Power, Integral antenna 03 Standard Power, uFl connector 04 High power, uFl connector Where this Data Sheet is denoted as "Advanced" or "Preliminary", devices will be either Engineering Samples or Prototypes. Devices of this status have an Rx suffix after the module type to identify qualification status during these product phases - for example, JN5148-001-M00R1T. Part Number Ordering Code Description JN5148-001-M00T JN5148-001-M/00T JN5148 module, variant as detailed above JN5148-001-M03T JN5148-001-M/03T JN5148-001-M04T JN5148-001-M/04T Label line 1: IC ID Number Label line 2: FCC ID Number Label line 3: Part Number Label line 4: Barcode Label Label line 5: YYWWTNNNNN (see below) IC: 7438A CYO5148M0 FCC ID: TYOJN5148M0 JN51XX-XXX-XXX JENNIC Identifier YY WW T NNNNN Description Year Week Module type Serial Number Format 06 (example) 45 (example) YYWWTNNNNN Figure 8: Example module labelling for FCC approved modules (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 15 A.5 Tape and Reel Information: A.5.1 Tape Orientation and dimensions All dimensions are in mm Module type: A B W F E P0 P1 P2 T Cover Tape width (W) JN5148-001-M00 18.4 32.6 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5148-001-M03 18.4 30.4 44 20.2 1.75 4.0 2.0 24.0 3.4 37.5 JN5148-001-M04 18.5 40.9 56 26.2 1.75 4.0 2.0 24.0 3.4 49.5 Tolerance 0.1 0.1 0.3 0.1 +0.1 0.1 0.1 0.1 0.1 0.1 A.5.2 Cover tape details Thickness (T) 0.061mm Surface resistivity (component side) 104 to 107 Ohms/sq Surface resistivity (component side) Non-conductive Backing type: Polyester Adhesive type: PSA Sealing: Room ambient 16 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 A.5.3 Leader and Trailer 300 MM 300 MM A.5.4 Reel Dimensions: All dimensions are in mm. Module type: A B C N W (min) JN5148-xxx-M00/03 330 1.0 2.20.5 13 0.2 100 +0.1 44.5 0.3 JN5148-xxx-M04 330 1.0 2.20.5 13 0.2 100 +0.1 56.5 0.3 A.6 Related Documents [1] IEEE Std 802.15.4-2003 IEEE Standard for Information Technology - Part 15.4 Wireless Medium Access Control (MAC) and Physical Layer (PHY) Specifications for Low-Rate Wireless Personal Area Networks (LR-WPANs) [2] JN-DS-JN5148 Wireless Microcontroller Datasheet (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 17 A.7 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. WARNING! FCC Radiation Exposure Statement: This portable equipment with its antenna complies with FCC's RF radiation exposure limits set forth for an uncontrolled environment. To maintain compliance follow the instructions below; 1. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. Avoid direct contact to the antenna, or keep it to a minimum while using this equipment. This transmitter module is authorized to be used in other devices only by OEM integrators under the following condition: The transmitter module must not be co-located with any other antenna or transmitter. As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 18 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 A.7.1 Antennas approved by FCC for use with JN5148 modules Brand Model Number Description Gain (dBi) Connector type 1 Aveslink Technology, Inc E-0360-AT Patch Antenna - outdoor 18 RP-N 2 Aveslink Technology, Inc E-0260-AT Patch Antenna - outdoor 15 RP-N 3 Aveslink Technology, Inc E-1050-AT Vertical - outdoor colinear 15 RP-N 4 Aveslink Technology, Inc E-1040-AT Vertical - outdoor colinear 12 RP-N 5 Aveslink Technology, Inc E-0100-AC Patch Antenna - flying lead 10 RP-SMA 6 Aveslink Technology, Inc E-1030-AT Vertical - outdoor colinear 9 RP-N 7 Aveslink Technology, Inc E-1020-AT Vertical - outdoor colinear 7 RP-N 8 Aveslink Technology, Inc E-1710-GC Vertical - swivel 7 RP-SMA 9 Aveslink Technology, Inc E-1710-GM Vertical - swivel 7 RP-TNC 10 Aveslink Technology, Inc E-1511-GC Vertical - swivel 5 RP-SMA 11 Aveslink Technology, Inc E-0030-AA Patch Antenna - flying lead 4 uFL 12 Aveslink Technology, Inc E-0030-AC Patch Antenna - flying lead 4 RP-SMA 13 Aveslink Technology, Inc E-1204-AC Ceiling antenna - flying lead 4 RP-SMA 14 Aveslink Technology, Inc E-1520-CA Vertical - bulkhead- flying lead 4 uFL 15 Aveslink Technology, Inc E-1520-GC Vertical - swivel 4 RP-SMA 16 Aveslink Technology, Inc E-1450-GC Vertical-swivel mount 4 RP-SMA 17 Nearson S152CL-L-PX-2450S Vertical - knuckle-flying lead 4 uFL 18 Antenna Factor ANT-2.4-CW-RCL Vertical - knuckle antenna 2.9 RP-SMA 19 Aveslink Technology, Inc E-0901-AA Embedded - flying lead 2.5 uFL 20 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 21 Antennova 2010B6090-01 Vertical - knuckle antenna 2.2 RP-SMA 22 Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 2.2 RP-SMA 23 Aveslink Technology, Inc E-0005-AC Vertical- flying lead 2 RP-SMA 24 Aveslink Technology, Inc E-2411-GC Vertical - swivel 2 RP-SMA 25 Aveslink Technology, Inc E-2410-CA Vertical - bulkhead- flying lead 2 uFL 26 Aveslink Technology, Inc E-2410-GC Vertical - swivel 2 RP-SMA 27 Aveslink Technology, Inc E-2820-CA Vertical - bulkhead- flying lead 2 uFL 28 Aveslink Technology, Inc E-2820-GC Vertical - swivel 2 RP-SMA 29 Aveslink Technology, Inc E-0903-AX Embedded - nickel silver strip 2 None 30 Aveslink Technology, Inc E-0904-AX Embedded - nickel silver strip 2 None 31 Embedded Antenna Design FBKR35068-RS-KR Vertical - knuckle antenna 2 RP-SMA 32 Nearson S131CL-L-PX-2450S Vertical - knuckle-flying lead 2 uFL 33 Laird Technologies WRR2400-IP04 Vertical - knuckle-flying lead 1.5 uFL 34 Laird Technologies WRR2400-RPSMA Vertical - knuckle-flying lead 1.3 RP-SMA 35 Aveslink Technology, Inc E-6170-DA Vertical - right angle 1 uFL 36 Laird Technologies WCR2400-SMRP Vertical - knuckle antenna 1 RP-SMA 37 Siretta 2.6 uFL ANTC0010G0200GQ12 PCB antenna - flying lead uFL These antennae or versions with alternative connectors may be used to meet European regulations. (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 19 This device has been designed to operate with the antennas listed above, and having a maximum gain of 4.4 dBi. Antennas not included in this list or having a gain greater than 4.4 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. A.7.2 High Power Module usage limitation The high power module variants are classified as `mobile' device pursuant with FCC 2.1091 and must not be used at a distance of < 20 cm (8") from any people. IMPORTANT NOTE: In the event that these conditions can not be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual for the end product must include the following information in a prominent location; "To comply with FCC's RF radiation exposure requirements, the antenna(s) used for this transmitter must not be colocated or operating in conjunction with any other antenna or transmitter." A.7.3 High Power Module channel restriction The FCC grant for the TYOJN5148M4 does not permit the use of channel 26. Access to channel 26 is forbidden by the 802.15.4 MAC layer when the JN5148 chip is in high power mode. Users will not be able to access channel 26 when using the JN5148-001-M04 module under any circumstances. A.7.4 FCC End Product Labelling The final `end product' should be labelled in a visible area with the following: "Contains TX FCC ID: TYOJN5148M0, TYOJN5148M3 or TYOJN5148M4 " to reflect the version of the module being used inside the product. A.8 Industry Canada Statement To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. These modules have been designed to operate with antennas having a maximum gain of 18 dBi. Antennas having a gain greater than 18 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. As long as the above condition is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc). A.8.1 Industry Canada End Product Labelling For Industry Canada purposes the following should be used. "Contains Industry Canada ID IC: 7438A-CYO5148M0, IC: 7438A-CYO5148M3 or IC: 7438A-CYO5148M4" to reflect the version of the module being used inside the product. 20 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 A.9 European R & TTE Directive 1999/5/EC Statement All modules listed in this datasheet are compliant with ETSI EN 300 328V1.7.1 (2006/05) and are subject to a Notified Body Opinion. The modules are approved for use with the antennas listed in the following table. The high power module M04 is limited to an antenna with a gain of 2.2 dBi or less and is approved for use with a reduced output power: +10dBm EIRP is the maximum permitted. Brand Model Number Description 1 Aveslink Technology, Inc E-0100-AC Patch Antenna - flying lead Gain (dBi) Connector type 10 RP-SMA 2 Aveslink Technology, Inc E-1030-AT Vertical - outdoor colinear 9 RP-N 3 Aveslink Technology, Inc E-1020-AT Vertical - outdoor colinear 7 RP-N 4 Aveslink Technology, Inc E-1710-GC Vertical - swivel 7 RP-SMA 5 Aveslink Technology, Inc E-1710-GM Vertical - swivel 7 RP-TNC 6 Aveslink Technology, Inc E-1511-GC Vertical - swivel 5 RP-SMA 7 Aveslink Technology, Inc E-0030-AA Patch Antenna - flying lead 4 uFL 8 Aveslink Technology, Inc E-0030-AC Patch Antenna - flying lead 4 RP-SMA 9 Aveslink Technology, Inc E-1204-AC Ceiling antenna - flying lead 4 RP-SMA 10 Aveslink Technology, Inc E-1520-CA Vertical - bulkhead- flying lead 4 uFL 11 Aveslink Technology, Inc E-1520-GC Vertical - swivel 4 RP-SMA 12 Aveslink Technology, Inc E-1450-GC Vertical-swivel mount 4 RP-SMA 13 Nearson S152CL-L-PX-2450S Vertical - knuckle-flying lead 4 uFL 14 Antenna Factor ANT-2.4-CW-RCL Vertical - knuckle antenna 2.9 RP-SMA 15 Aveslink Technology, Inc E-0901-AA Embedded - flying lead 2.5 uFL 16 Antenna Factor ANT-2.4-CW-RCT-RP Vertical - knuckle antenna 2.2 RP-SMA 17 Antennova 2010B6090-01 Vertical - knuckle antenna 2.2 RP-SMA 18 Hyperlink Technology HG2402RD-RSF Vertical - knuckle antenna 2.2 RP-SMA 19 Aveslink Technology, Inc E-0005-AC Vertical- flying lead 2 RP-SMA 20 Aveslink Technology, Inc E-2411-GC Vertical - swivel 2 RP-SMA 21 Aveslink Technology, Inc E-2410-CA Vertical - bulkhead- flying lead 2 uFL 22 Aveslink Technology, Inc E-2410-GC Vertical - swivel 2 RP-SMA 23 Aveslink Technology, Inc E-2820-CA Vertical - bulkhead- flying lead 2 uFL 24 Aveslink Technology, Inc E-2820-GC Vertical - swivel 2 RP-SMA 25 Aveslink Technology, Inc E-0903-AX Embedded - nickel silver strip 2 None 26 Aveslink Technology, Inc E-0904-AX Embedded - nickel silver strip 2 None 27 Embedded Antenna Design FBKR35068-RS-KR Vertical - knuckle antenna 2 RP-SMA 28 Nearson S131CL-L-PX-2450S Vertical - knuckle-flying lead 2 uFL 29 Laird Technologies WRR2400-IP04 Vertical - knuckle-flying lead 1.5 uFL 30 Laird Technologies WRR2400-RPSMA Vertical - knuckle-flying lead 1.3 RP-SMA 31 Aveslink Technology, Inc E-6170-DA Vertical - right angle 1 uFL 32 Laird Technologies WCR2400-SMRP Vertical - knuckle antenna 1 RP-SMA 33 Siretta 2.6 uFL (c) NXP Laboratories UK 2010 ANTC0010G0200GQ12 PCB antenna - flying lead uFL JN-DS-JN5148-001-Myy 1v4 21 A.10 RoHS Compliance JN5148-001-Myy devices meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). The JN5148-001-M00, M03 and M04 modules meet the requirements of Chinese RoHS requirements SJ/T113632006. Full data can be found at www.nxp.com/jennic. A.11 Status Information The status of this Data Sheet is Production. Jennic products progress according to the following format: Advanced The Data Sheet shows the specification of a product in planning or in development. The functionality and electrical performance specifications are target values and may be used as a guide to the final specification. Jennic reserves the right to make changes to the product specification at anytime without notice. Preliminary The Data Sheet shows the specification of a product that is commercially available, but is not yet fully qualified. The functionality of the product is final. The electrical performance specifications are target values and may be used as a guide to the final specification. Modules are identified with an Rx suffix, for example JN5148-001-M00R2. Jennic reserves the right to make changes to the product specification at anytime without notice. Production This is the production Data Sheet for the product. All functional and electrical performance specifications, where included, including min and max values are derived from detailed product characterization. This Data Sheet supersedes all previous document versions. Jennic reserves the right to make changes to the product specification at anytime. A.12 Disclaimers The contents of this document are subject to change without notice. Jennic reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained therein. Information contained in this document regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. Jennic warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Jennic's standard warranty. Testing and other quality control techniques are used to the extent Jennic deems necessary to support this warranty. Except where mandatory by government requirements, testing of all parameters of each product is not necessarily performed. Jennic assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work infringement, unless otherwise specified. Jennic products are not intended for use in life support systems, appliances or systems where malfunction of these products can reasonably be expected to result in personal injury, death or severe property or environmental damage. Jennic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Jennic for any damages resulting from such use. All products are sold subject to Jennic's terms and conditions of sale supplied at the time of order acknowledgment. All trademarks are the property of their respective owners. 22 JN-DS-JN5148-001-Myy 1v4 (c) NXP Laboratories UK 2010 Version Control Version Notes 1.0 1st Issue of Advanced Datasheet 1.1 1st Issue of Preliminary Datasheet, minor parametric changes and addition of Appendix A6.3 1.2 1st Issue of Production Datasheet, addition of PCB cleaning information in Appendix A3 1.3 Logo updated and support of JenNet added 1.4 Ordering information changed NXP Laboratories UK Ltd (Formerly Jennic Ltd) Furnival Street Sheffield S1 4QT United Kingdom Tel: +44 (0)114 281 2655 Fax: +44 (0) 114 281 2951 E-mail: info@jennic.com For the contact details of your local Jennic office or distributor, refer to the Jennic web site: www.nxp.com/jennic (c) NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 23