ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER GENERAL DESCRIPTION FEATURES The ICS83054I is a low skew, 4:1, Singleended Multiplexer and a member of the HiPerClockSTM HiPerClockS TM family of High Performance Clock Solutions from ICS. The ICS83054I has four selectable single-ended clock inputs and one single-ended clock output. The output has a VDDO pin which may be set at 3.3V, 2.5V, or 1.8V, making the device ideal for use in voltage translation applications. An output enable pin places the output in a high impedance state which may be useful for testing or debug. The device operates up to 250MHz and is packaged in a 16 TSSOP. * 4:1 single-ended multiplexer ICS * Q nominal output impedance: 7 (VDDO =3 .3V) * Maximum output frequency: 250MHz * Propagation delay: 3ns (maximum), VDD = VDDO = 3.3V * Input skew: 225ps (maximum), VDD = VDDO = 3.3V * Part-to-part skew: 475ps (maximum), VDD = VDDO = 3.3V * Operating supply modes: VDD/VDDO 3.3V/3.3V 3.3V/2.5V 3.3V/1.8V 2.5V/2.5V 2.5V/1.8V * -40C to 85C ambient operating temperature * Available in both standard and lead-free RoHS-compliant packages BLOCK DIAGRAM PIN ASSIGNMENT Q nc OE CLK3 GND nc SEL1 CLK2 CLK0 CLK1 Q CLK2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDDO nc CLK0 nc VDD nc CLK1 SEL0 CLK3 ICS83054I 16-Lead TSSOP 4.4mm x 5.0mm x 0.92mm package body G Package Top View SEL1 SEL0 OE 83054AGI www.icst.com/products/hiperclocks.html 1 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER TABLE 1. PIN DESCRIPTIONS Number Name Type 1 Q Output 3 OE Input 4, 8, 10, 14 5 CLK3, CLK2, CLK1, CLK0 GND Input Pulldown Single-ended clock inputs. LVCMOS/LVTTL interface levels. Power 7, 9 SEL1, SEL0 Input 2, 6, 11, 13, 15 nc Unused Power supply ground. Clock select input. See Control Input Function Table. Pulldown LVCMOS / LVTTL interface levels. No connect. 12 VDD Power Core and input supply pin. 16 VDDO Power Output supply pin. Pullup Description Single-ended clock output. LVCMOS/LVTTL interface levels. Output enable. When LOW, outputs are in HIGH impedance state. When HIGH, outputs are active. LVCMOS / LVTTL interface levels. NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values. TABLE 2. PIN CHARACTERISTICS Symbol Parameter Test Conditions Minimum Typical Maximum Units CIN Input Capacitance 4 pF RPULLUP Input Pullup Resistor 51 k RPULLDOWN Input Pulldown Resistor Power Dissipation Capacitance (per output) C PD ROUT Output Impedance 51 k VDDO = 3.465V 18 pF VDDO = 2.625V 20 pF VDDO = 1.89V 30 pF VDDO = 3.465V 7 VDDO = 2.625V 7 VDDO = 1.89V 10 TABLE 3. CONTROL INPUT FUNCTION TABLE Control Inputs SEL1 SEL0 0 0 83054AGI Input Selected to Q CLK0 0 1 CLK1 1 0 CLK2 1 1 CLK3 www.icst.com/products/hiperclocks.html 2 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER ABSOLUTE MAXIMUM RATINGS Supply Voltage, VDD 4.6V Inputs, VI -0.5V to VDD + 0.5 V Outputs, VO -0.5V to VDDO + 0.5V Package Thermal Impedance, JA 89C/W (0 lfpm) Storage Temperature, TSTG -65C to 150C NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDO = 3.3V5%, TA = -40C TO 85C Symbol Parameter Test Conditions Minimum Typical Maximum Units VDD Core Supply Voltage 3.135 3.3 3.465 V VDDO Output Supply Voltage 3.135 3.3 3.465 V IDD Power Supply Current 40 mA IDDO Output Supply Current 5 mA Maximum Units TABLE 4B. POWER SUPPLY DC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 2.5V5%, TA = -40C TO 85C Symbol Parameter Test Conditions Minimum Typical VDD Core Supply Voltage 3.135 3.3 3.465 V VDDO Output Supply Voltage 2.375 2. 5 2.625 V IDD Power Supply Current 40 mA IDDO Output Supply Current 5 mA TABLE 4C. POWER SUPPLY DC CHARACTERISTICS, VDD = 3.3V5%, VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol Parameter V DD Core Supply Voltage Test Conditions Minimum Typical Maximum Units 3.135 3.3 3.465 V 1.71 1.8 VDDO Output Supply Voltage 1.89 V IDD Power Supply Current 40 mA IDDO Output Supply Current 5 mA TABLE 4D. POWER SUPPLY DC CHARACTERISTICS, VDD = VDDO = 2.5V5%, TA = -40C TO 85C Symbol Parameter Minimum Typical Maximum Units VDD Core Supply Voltage Test Conditions 2.375 2.5 2.625 V VDDO Output Supply Voltage 2.375 2.5 2.625 V IDD Power Supply Current 35 mA IDDO Output Supply Current 5 mA TABLE 4E. POWER SUPPLY DC CHARACTERISTICS, VDD = 2.5V5%, VDDO = 1.8V0.2V, TA = -40C TO 85C Symbol Parameter VDD Core Supply Voltage Test Conditions Minimum Typical Maximum Units 2.375 2. 5 2.625 V 1.71 1. 8 VDDO Output Supply Voltage 1.89 V IDD Power Supply Current 35 mA IDDO Output Supply Current 5 mA 83054AGI www.icst.com/products/hiperclocks.html 3 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER TABLE 4F. LVCMOS/LVTTL DC CHARACTERISTICS, TA = -40C TO 85C Symbol VIH VIL IIH IIL VOH VOL Parameter Input High Voltage Input Low Voltage Input High Current Input Low Current CLK0:CLK3, SEL0, SEL1 OE CLK0:CLK3, SEL0, SEL1 OE Output HighVoltage Output Low Voltage Test Conditions Minimum Maximum Units VDD = 3.3V 5% 2 Typical VDD + 0.3 V VDD = 2.5V 5% 1.7 VDD + 0.3 V VDD = 3.3V 5% -0.3 0.8 V VDD = 2.5V 5% -0.3 0.7 V VDD = 3.3V or 2.5V 5% 150 A VDD = 3.3V or 2.5V 5% 5 A VDD = 3.3V or 2.5V 5% -5 A VDD = 3.3V or 2.5V 5% -150 A VDDO = 3.3V 5%; NOTE 1 2.6 V VDDO = 2.5V 5%; NOTE 1 1.8 V VDDO = 1.8V 5%; NOTE 1 VDD - 0.3 V VDDO = 3.3V 5%; NOTE 1 0.5 V VDDO = 2.5V 5%; NOTE 1 0.45 V VDDO = 1.8V 5%; NOTE 1 0.35 V NOTE 1: Outputs terminated with 50 to VDDO/2. See Parameter Measurement section, "Load Test Circuit" diagrams. TABLE 5A. AC CHARACTERISTICS, VDD = VDDO = 3.3V 5%, TA = -40C TO 85C Symbol Parameter fMAX Output Frequency Test Conditions Minimum Typical Maximum Units 250 MHz tpLH Propagation Delay, Low to High; NOTE 1 2.4 2. 7 3.0 ns tpHL Propagation Delay, High to Low; NOTE 1 2.5 2.7 2.9 ns t sk(i) Input Skew; NOTE 2 t sk(pp) Par t-to-Par t Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time odc Output Duty Cycle 55 20% to 80% 22 5 ps 475 ps 50 50 0 ps 45 55 @ 100MHz 45 MUXISOL MUX Isolation NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Defined as skew between outputs on different devices operating a the same supply voltages and with equal load conditions. Using the same type of input on each device, the output is measured at VDDO/2. 83054AGI www.icst.com/products/hiperclocks.html 4 % dB REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER TABLE 5B. AC CHARACTERISTICS, VDD = 3.3V 5%, VDDO = 2.5V 5%, TA = -40C TO 85C Symbol Parameter fMAX Output Frequency Test Conditions Minimum Typical Maximum Units 250 MHz tpLH Propagation Delay, Low to High; NOTE 1 2.5 2.8 3.1 ns tpHL Propagation Delay, High to Low; NOTE 1 2.6 2.8 3.0 ns t sk(i) Input Skew; NOTE 2 45 150 ps t sk(pp) Par t-to-Par t Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time odc Output Duty Cycle 20% to 80% 400 ps 50 50 0 ps 45 55 @ 100MHz 45 MUXISOL MUX Isolation NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Defined as skew between outputs on different devices operating a the same supply voltages and with equal load conditions. Using the same type of input on each device, the output is measured at VDDO/2. % dB TABLE 5C. AC CHARACTERISTICS, VDD = 3.3V 5%, VDDO = 1.8V 5%, TA = -40C TO 85C Symbol Parameter fMAX Output Frequency Test Conditions Minimum Typical Maximum Units 250 MHz tpLH Propagation Delay, Low to High; NOTE 1 2.7 3.2 3.8 ns tpHL Propagation Delay, High to Low; NOTE 1 2.8 3.3 3.8 ns t sk(i) Input Skew; NOTE 2 t sk(pp) Par t-to-Par t Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time odc Output Duty Cycle 50 20% to 80% 150 ps 475 ps 100 700 ps 45 55 @ 100MHz 45 MUXISOL MUX Isolation NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Defined as skew between outputs on different devices operating a the same supply voltages and with equal load conditions. Using the same type of input on each device, the output is measured at VDDO/2. 83054AGI www.icst.com/products/hiperclocks.html 5 % dB REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER TABLE 5D. AC CHARACTERISTICS, VDD = VDDO = 2.5V 5%, TA = -40C TO 85C Symbol Parameter Test Conditions Minimum Typical Maximum Units 250 MHz 3.5 ns fMAX Output Frequency tpLH Propagation Delay, Low to High; NOTE 1 2.5 3.0 2.5 2.9 3.4 ns 60 17 5 ps tpHL Propagation Delay, High to Low; NOTE 1 t sk(i) Input Skew; NOTE 2 t sk(pp) Par t-to-Par t Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time odc Output Duty Cycle 20% to 80% 300 ps 100 500 ps 40 60 % @ 100MHz 45 MUXISOL MUX Isolation NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Defined as skew between outputs on different devices operating a the same supply voltages and with equal load conditions. Using the same type of input on each device, the output is measured at VDDO/2. dB TABLE 5E. AC CHARACTERISTICS, VDD = 2.5V 5%, VDDO = 1.8V -5%, TA = -40C TO 85C Symbol Parameter Test Conditions Minimum Typical Maximum Units 250 MHz 4.0 ns fMAX Output Frequency tpLH Propagation Delay, Low to High; NOTE 1 2.6 3.3 2.7 3.3 4.0 ns 50 150 ps 325 ps 10 0 70 0 ps 40 60 % tpHL Propagation Delay, High to Low; NOTE 1 t sk(i) Input Skew; NOTE 2 t sk(pp) Par t-to-Par t Skew; NOTE 2, 3 tR / tF Output Rise/Fall Time odc Output Duty Cycle 20% to 80% @ 100MHz 45 MUXISOL MUX Isolation NOTE 1: Measured from VDD/2 of the input to VDDO/2 of the output. NOTE 2: This parameter is defined in accordance with JEDEC Standard 65. NOTE 3: Defined as skew between outputs on different devices operating a the same supply voltages and with equal load conditions. Using the same type of input on each device, the output is measured at VDDO/2. 83054AGI www.icst.com/products/hiperclocks.html 6 dB REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER PARAMETER MEASUREMENT INFORMATION 1.65V5% 1.25V5% SCOPE VDD, VDDO LVCMOS SCOPE VDD, VDDO Qx Qx LVCMOS GND GND -1.65V5% -1.25V5% 3.3V CORE/3.3V OUTPUT LOAD AC TEST CIRCUIT 2.5V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT 2.05V5% 2.45% 1.25V5% SCOPE V DD VDDO LVCMOS 0.9V5% SCOPE V DD VDDO Qx Qx LVCMOS GND GND -0.9V5% -1.25V5% 3.3V CORE/2.5V OUTPUT LOAD AC TEST CIRCUIT 3.3V CORE/1.8V OUTPUT LOAD AC TEST CIRCUIT 1.6V5% 0.9V5% Part 1 SCOPE VDD VDDO LVCMOS Qx V DDO 2 Qx Part 2 GND Qy V DDO 2 tsk(pp) -0.9V5% 2.5 CORE/1.8V OUTPUT LOAD AC TEST CIRCUIT 83054AGI PART-TO-PART SKEW www.icst.com/products/hiperclocks.html 7 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. VDD VDD CLK0:CLK7 2 2 VDDO Q 4:1, SINGLE-ENDED MULTIPLEXER 2 tpLH VDDO Clock Outputs 2 tpHL PROPAGATION DELAY 80% 80% tR tF 20% 20% OUTPUT RISE/FALL TIME CLKx V DDO 2 Q Q t PW t tPD1 odc = PERIOD t PW x 100% t PERIOD CLKy Q tPD2 tsk(i) = tPD2 - tPD1 INPUT SKEW 83054AGI OUTPUT DUTY CYCLE/PULSE WIDTH/PERIOD www.icst.com/products/hiperclocks.html 8 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER APPLICATION INFORMATION RECOMMENDATIONS FOR UNUSED INPUT PINS INPUTS: CLK INPUT: For applications not requiring the use of a clock input, it can be left floating. Though not required, but for additional protection, a 1k resistor can be tied from the CLK input to ground. 83054AGI LVCMOS CONTROL PINS: All control pins have internal pull-ups or pull-downs; additional resistance is not required but can be added for additional protection. A 1k resistor can be used. www.icst.com/products/hiperclocks.html 9 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER RELIABILITY INFORMATION TABLE 6. JAVS. AIR FLOW TABLE FOR 16 LEAD TSSOP JA by Velocity (Linear Feet per Minute) 0 Single-Layer PCB, JEDEC Standard Test Boards Multi-Layer PCB, JEDEC Standard Test Boards 137.1C/W 89.0C/W 200 118.2C/W 81.8C/W 500 106.8C/W 78.1C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS83054I is: 874 83054AGI www.icst.com/products/hiperclocks.html 10 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. PACKAGE OUTLINE - G SUFFIX 4:1, SINGLE-ENDED MULTIPLEXER FOR 16 LEAD TSSOP TABLE 7. PACKAGE DIMENSIONS Millimeters SYMBOL Minimum N Maximum 16 A -- 1.20 A1 0.05 0.15 A2 0.80 1.05 b 0.19 0.30 c 0.09 0.20 D 4.90 5.10 E E1 6.40 BASIC 4.30 e 4.50 0.65 BASIC L 0.45 0.75 0 8 aaa -- 0.10 Reference Document: JEDEC Publication 95, MO-153 83054AGI www.icst.com/products/hiperclocks.html 11 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER TABLE 8. ORDERING INFORMATION Part/Order Number Marking Package Shipping Packaging Temperature ICS83054AGI 83054AGI 16 Lead TSSOP tube -40C to 85C ICS83054AGIT 83054AGI 16 Lead TSSOP 2500 tape & reel -40C to 85C ICS83054AGILF 83054AIL 16 Lead "Lead-Free" TSSOP tube -40C to 85C ICS83054AGILFT 83054AIL 16 Lead "Lead-Free" TSSOP 2500 tape & reel -40C to 85C NOTE: Par ts that are ordered with an "LF" suffix to the par t number are the Pb-Free configuration and are RoHS compliant. The aforementioned trademark, HiPerClockS is a trademark of Integrated Circuit Systems, Inc. or its subsidiaries in the United States and/or other countries. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial and industrial applications. Any other applications such as those requiring high reliability or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 83054AGI www.icst.com/products/hiperclocks.html 12 REV. A JANUARY 3, 2006 ICS83054I Integrated Circuit Systems, Inc. 4:1, SINGLE-ENDED MULTIPLEXER REVISION HISTORY SHEET Rev Table Page A T8 12 83054AGI Description of Change Ordering Information Table - corrected Par t/Order Numbers. www.icst.com/products/hiperclocks.html 13 Date 1/3/06 REV. A JANUARY 3, 2006