SNAP-ODC5SRCFM - OPTO 22 - Datasheet.Directory

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

PAGE

1

DATA SHEET

Form 1144-101029

SNAP Digital Output Modules

Features

Four channels per module

Convenient pluggable wiring terminals; accepts up to

14 AWG wire

Powered by a single 5-volt supply

Channel-specific LEDs

Operating temperature: 0 to 70 °C

UL and CE approved (most modules); Factory Mutual

approved (part numbers ending in FM)

Description

Opto 22 SNAP I/O digital output

modules are part of the SNAP PAC

System.

Customers can choose from AC or DC

models. Optical isolation on all solid-

state modules provides 4,000 volts of

transient (4000 V for 1 ms) protection

for sensitive control electronics from

industrial field signals.

All SNAP digital modules have

removable top-mounted connectors

to provide easy access for field wiring.

All operate on 5 VDC control logic.

Each digital module features integral

channel-specific LEDs for convenient

troubleshooting and maintenance.

Each module is factory tested twice

before shipment, and most modules

are UL and CE approved. In addition,

part numbers ending in FM are

Factory Mutual approved.

SNAP output modules are used to

switch up to four separate AC or DC

loads. Output modules that are fused

use a standard fuse with a convenient

handle for easy replacement. DC

outputs are available in either a source

or sink configuration. AC outputs are

zero voltage turn on and zero current

turn off for transient-free switching.

The dry contact modules allow

switching of low power signals where

signal integrity must be maintained,

or where zero leakage current is a

requirement. Dry contact modules are

Part Numbers

Part Description See

pages

SNAP-OAC5 SNAP 4-channel 12–250 VAC output, 5 VDC logic 3, 5

SNAP-OAC5MA SNAP 4-channel isolated 12–250 V AC output, 5 VDC logic

with manual/auto switches 3, 6

SNAP-OAC5FM SNAP 4-channel 12–250 VAC output, 5 VDC logic 4, 5

SNAP-OAC5-i SNAP 4-channel isolated 12–250 VAC output, 5 VDC logic 3, 7

SNAP-OAC5-iFM SNAP 4-channel isolated 12–250 VAC output, 5 VDC logic 4, 7

SNAP-ODC5SRC SNAP 4-channel 5–60 VDC output, 5 VDC logic source 8, 14

SNAP-ODC5SRCFM SNAP 4-channel 5–60 VDC output, 5 VDC logic source 11, 14

SNAP-ODC5SNK SNAP 4-channel 5–60 VDC output, 5 VDC logic sink 8, 15

SNAP-ODC5SNKFM SNAP 4-channel 5–60 VDC output, 5 VDC logic sink 11, 15

SNAP-ODC5ASNK SNAP 4-channel 5–200 VDC output, 5 VDC logic sink 10, 15

SNAP-ODC5R* SNAP 4-channel dry contact output, normally open 9, 16

SNAP-ODC5RFM* SNAP 4-channel dry contact output, normally open 12, 16

SNAP-ODC5R5* SNAP 4-channel dry contact output, normally closed 9, 16

SNAP-ODC5R5FM* SNAP 4-channel dry contact output, normally closed 12, 16

SNAP-ODC5MA SNAP 4-channel isolated 5–60 VDC output, 5 VDC logic

with manual/auto switches 10, 17

SNAP-ODC5-i SNAP 4-channel isolated 5–60 VDC output, 5 VDC logic 10, 18

SNAP-ODC5-iFM SNAP 4-channel isolated 5–60 VDC output, 5 VDC logic 13, 18

SNAP-ODC5A-i SNAP 4-channel isolated 5–200 VDC output, 5 VDC logic 10, 18

SNAP-ODC5A-iFM SNAP 4-channel isolated 5–200 VDC output, 5 VDC logic 13, 18

SNAP-RETN4 SNAP 4-module retention rail (OEM) --------

SNAP-RETN4B SNAP 4-module retention rail, 25-pack (OEM) --------

SNAP-RETN6 SNAP 6-module retention rail (OEM) --------

SNAP-RETN6B SNAP 6-module retention rail, 25-pack (OEM) --------

SNAP-FUSE4AB SNAP 4-amp fuse, 25-pack --------

SNAP-MODFUSEH SNAP digital output module fuse holder, 10-pack --------

*Not UL approved

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

2

DATA SHEET

Form 1144-101029

not solid-state devices. They use reed relays, which are

electromechanical devices. These modules do not provide

optical isolation. Current rating for dry contact modules

depends on the voltage they are used with, as shown in the

graph on page 16.

SNAP-OAC5MA and SNAP-ODC5MA are special modules

featuring manual-on/manual-off/automatic switches, ideal for

diagnostic testing of control applications. The switches

override output from the application, so you can quickly check

field device wiring. These modules each contain four isolated

channels.

The SNAP-OAC5-i, SNAP-ODC5-i, and SNAP-ODC5A-i modules

provide four isolated output channels.

For Ethernet-based applications requiring higher density of

digital I/O points, see Opto 22 form #1556, the SNAP High-

Density Digital Module Data Sheet.

I/O Processor Compatibility

SNAP digital output modules are compatible with all SNAP

PAC brains and rack-mounted controllers, including both

standard wired models and Wired+Wireless™ models.

Notes for legacy hardware: SNAP digital output modules

are also compatible with SNAP Ultimate, SNAP Ethernet, and

SNAP Simple brains, as well as other SNAP brains such as the

serial B3000 and the B3000HA. These modules can also be

used on B-series and

M-series mounting racks.

Installation

The following diagram shows part of a SNAP mounting rack.

The rack is shown without screw connectors.

Modules snap securely into place in the row of connectors on

the rack. Each module connector has a number. Digital output

modules and other types of SNAP I/O modules are mounted

on the module connectors starting at module position zero.

NOTE: Check the data sheet or user’s guide for the brain or on-

the-rack controller you are using to determine module

features available and any restrictions on module placement.

1. Place the rack so that the module connector numbers

are right-side up, with zero on the left, as shown in the

diagram above. (If your rack has screw connectors, the

screw connectors will be at the bottom.)

2. Position the module over the module connector,

aligning the small slot at the base of the module with

the retention bar on the rack. When positioning modules

next to each other, be sure to align the male and female

module keys at the tops of the modules before snapping

a module into position.

3. With the module correctly aligned, push on the module

to snap it into place.

4. (Optional) Use standard 4-40 x 1/2 truss-head Phillips

hold-down screws to secure both sides of each module.

CAUTION: Do not over-tighten screws.

5. Follow the wiring diagrams beginning on page 5 to

attach modules to the devices they monitor.

Modules require a special tool (provided) for removal.

Module

position zero Module connectors

Processor Retention bar

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

3

Specifications—AC Modules

SNAP-OAC5 SNAP-OAC5MA SNAP-OAC5-i

Key Feature -- Diagnostic switches

Four isolated channels Four isolated channels

Field Side Ratings (each channel)

Line Voltage - Range 24–250 VAC 24–250 VAC 24–250 VAC

Line Voltage - Nominal 120/240 VAC 120/240 VAC 120/240 VAC

Current Rating

0 °C to 70 °C Ambient 3 amps per module 3 amps per module 3 amps per module

One Cycle Surge 80 amps peak (50/60 Hz) 80 amps peak (50/60 Hz) 80 amps peak (50/60 Hz)

Minimum Load Current 20 mA 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps

Off-state Leakage at

Nominal Voltage - 60 Hz 2.5 mA @ 240 VAC

1.25 mA @ 120 VAC 2.5 mA @ 240 VAC

1.25 mA @ 120 VAC

Peak Blocking Voltage 500 V 500 V 500 V

Operating Frequency 25–65 Hz 25–65 Hz 25–65 Hz

dV/ dt - Off-state 200 volts/msec 200 volts/msec 200 volts/msec

dV/ dt - Commutating Snubbed for rated 0.5

power factor load Snubbed for rated 0.5 power

factor load Snubbed for rated 0.5 power

factor load

Fuse

(Common to all Channels)

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part

No. BEL 5HF4

Opto 22 Part No. SNAP-4A

Has four isolated channels.

User must provide own fus-

ing.

Has four isolated channels.

User must provide own fus-

ing.

Channel-to-channel isolation Not applicable 300 VAC

(1500 V transient) 300 VAC

(1500 V transient)

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms 220 ohms

Logic Supply Voltage 5 V DC ± 0.25 VDC 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per

Module 4 4 4

Turn-on Time 0.5 cycle maximum

(zero volts crossover) 0.5 cycle maximum

(zero volts crossov er) 0.5 cycle maximum

(zero volts crossover)

Turn-off Time 0.5 cycle maximum

(zero current crossover) 0.5 cycle maximum

(zero current crossover)

Isolation (Field Side to Logic

Side) 4,000 volts (transient) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 ° to 70 °C, operating

-30 ° to 85 °C, storage 0 ° to 70 °C, operating

-30 ° to 85 °C, storage

Agency Approvals UL, CE, CSA, RoHS,

DFARS UL, CE, RoHS, DFARS UL, CE, RoHS, DFARS

Warranty Lifetime 30 months Lifetime

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

4

DATA SHEET

Form 1144-101029

Specifications—AC Modules (continued)

SNAP-OAC5-FM SNAP-OAC5-i-FM

Key Feature Factory Mutual approved Four isolated channels

Factory Mutual approved

Field Side Ratings (each channel)

Line Voltage - Range 24–250 VAC 24–250 VAC

Line Voltage - Nominal 120/240 VAC 120/240 VAC

Current Rating

0 °C to 70 °C Ambient 3 amps per module 3 amps per module

One Cycle Surge 80 amps peak (50/60 Hz) 80 amps peak (50/60 Hz)

Minimum Load Current 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps

Off-state Leakage at Nominal

Voltage - 60 Hz 2.5 mA @ 240 VAC

1.25 mA @ 120 VAC 2.5 mA @ 240 VAC

1.25 mA @ 120 VAC

Peak Blocking Voltage 500 V 500 V

Operating Frequency 25–65 Hz 25–65 Hz

dV/ dt - Off-state 200 volts/msec 200 volts/msec

dV/ dt - Commutating Snubbed for rated 0.5 power

factor load Snubbed for rated 0.5 power

factor load

Fuse

(Common to all Channels)

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part No.

BEL 5HF4

Opto 22 Part No. SNAP-4A

Has four isolated channels.

User must provide own fusing.

Channel-to-channel isolation Not applicable 300 VAC

(1500 V transient)

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Channels Per Module 4 4

Turn-on Time 0.5 cycle maximum

(zero volts crossover) 0.5 cycle maximum

(zero volts crossov er)

Turn-off Time 0.5 cycle maximum

(zero current crossover) 0.5 cycle maximum

(zero current crossover)

Isolation (Field Side to Logic

Side) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 ° to 70 °C, operating

-30 ° to 85 °C, storage 0 ° to 70 °C, operating

-30 ° to 85 °C, storage

Agency Approvals CE, FM, RoHS, DFARS CE, FM, RoHS, DFARS

Warranty Lifetime Lifetime

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

5

Schematics

SNAP-OAC5 Output Module Part Number Description

SNAP-OAC5 4-channel AC output 12–250 VAC 5 VDC logic

SNAP-OAC5FM 4-channel AC output 12–250 V AC 5 VDC logic,

Factory Mutual approved

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

6

DATA SHEET

Form 1144-101029

Schematics

SNAP-OAC5MA Output Module

With Manual/Auto Switches Part Number Description

SNAP-OAC5MA 4-channel isolated AC output 12–250 VAC, 5

VDC logic, with manual/auto switch

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

7

Schematics

SNAP-OAC5i Isolated Output Module Part Number Description

SNAP-OAC5-i 4-channel isolated AC output 12–250 VAC,

5 VDC logic

SNAP-OAC5-iFM 4-channel isolated AC output 12–250 VAC,

5 VDC logic, Factory Mutual approved

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

8

DATA SHEET

Form 1144-101029

Specifications—DC Modules

SNAP-ODC5SRC SNAP-ODC5SNK

Key Feature Load sourcing Load sinking

Field Side Ratings (each channel)

Line Voltage - Range 5–60 VDC 5–60 VDC

Line Voltage - Nominal 5–48 VDC 5–48 VDC

Current Rating 0 °C to 70

°C Ambient 3 amps per module 3 amps per module

Surge Current 5 amps peak for

1 second 5 amps peak for

1 second

Minimum Load 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps

Off-state Leakage 1 mA @ 60 VDC 1 mA @ 60 VDC

Peak Blocking Voltage 60 VDC 60 VDC

Fuse

(Common to all Channels)

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part No.

BEL 5HF4

Opto 22 Part SNAP-4A

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part No.

BEL 5HF4

Opto 22 Part SNAP-4A

Channel-to-channel

isolation Not applicable Not applicable

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per

Module 4 4

Turn-on Time 100 usec 100 usec

Turn-off Time 750 usec 750 usec

Isolation (Field Side to

Logic Side) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 to 70 °C, operating

-30 to 85 °C, storage 0 to 70 °C, operating

-30 to 85 °C, storage

Agency Approvals UL, CE, CSA, RoHS, DFARS UL, CE, CSA, RoHS, DFARS

Warranty Lifetime Lifetime

* The power rating of the dry contact module must not exceed 10 VA under steady state or

momentary in-rush conditions. For voltages at or below 20 volts, the current limit is

0.5 amps. For voltages above 20 volts, the maximum allowable current is determined by the

following equation: 10 VA / Voltage = Current maximum. Rating curve is in the data sheet.

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

9

Specifications—DC Modules (continued)

SNAP-ODC5R SNAP-ODC5R5

Key Feature Dry contact

Normally open Dry contact

Normally closed

Field Side Ratings (each channel)

Line Voltage - Range 0–100 VDC

0–130 VAC* 0–100 VDC

0–130 VAC*

Line Voltage - Nominal -- --

Current Rating 0 °C to 70

°C Ambient 0.5 amps switching* 0.5 amps switching*

Surge Current 0.5 amps* 0.5 amps*

Minimum Load 0 mA 0 mA

Output Voltage Drop 0 volts 0 volts

Off-state Leakage 0 mA 0 mA

Peak Blocking Voltage 100 VDC / 130 VAC 100 VDC / 130 VAC

Fuse

(Common to all Channels) Has four isolated channels.

User must provide own fusing. Has four isolated channels.

User must provide own fusing.

Channel-to-channel

isolation 300 VAC (1500 V

transient) 300 VAC (1500 V

transient)

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per

Module 4 4

Turn-on Time 500 usec 500 usec

Turn-off Time 500 usec 500 usec

Isolation (Field Side to

Logic Side) 1,500 volts (transient) 1,500 volts (transient)

Mechanical Life 200,000,000 cycles 200,000,000 cycles

Temperature 0 to 70 °C, operating

-30 to 85 °C, storage 0 to 70 °C, operating

-30 to 85 °C, storage

Agency Approvals CE, CSA, RoHS, DFARS CE, RoHS, DFARS

Warranty 30 months or mechanical life,

whichever comes first 30 months or mechanical life,

whichever comes first

* The power rating of the dry contact module must not exceed 10 VA under steady state or

momentary in-rush conditions. For voltages at or below 20 volts, the current limit is 0.5 amps.

For voltages above 20 volts, the maximum allowable current is determined by the following

equation: 10 VA / Voltage = Current maximum. Rating curve is in the data sheet.

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

10

DATA SHEET

Form 1144-101029

Specifications—DC Modules (continued)

SNAP-ODC5MA SNAP-ODC5-i SNAP-ODC5A-i SNAP-ODC5ASNK

Key Feature Diagnostic switches

Four isolated channels Four isolated channels Four isolated channels Load sinking

Field Side Ratings (each channel)

Line Voltage - Range 5–60 VDC 5–60 VDC 5–200 VDC 5–200 VDC

Line Voltage - Nominal 5–48 VDC 5–48 VDC 5–200 VDC 5–200 VDC

Current Rating

0 °C to 70 °C Ambient 2 amps per module

0.5 amps per channel 3 amps per module 3 amps per module 3 amps per module

Surge Current 1.5 amps peak for

1 second 5 amps peak for

1 second

Minimum Load 20 mA 20 mA 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@

0.75 amps 1.6 volts max.@

0.75 amps

Off-state Leakage 1 mA @ 60 VDC 1 mA @ 60 VDC 1 mA @ 200 VDC 1 mA @ 200 VDC

Peak Blocking Voltage 60 VDC 60 VDC 200 VDC 200 VDC

Fuse

(Common to all Channels)

Has four isolated

channels. User must

provide own fusing.

Has four isolated

channels. User must

provide own fusing.

Has four isolated

channels. User must

provide own fusing.

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse

Part No. BEL 5HF4

Opto 22 Part No.

SNAP-4A

Channel-to-channel

isolation 300 VAC

(1500 V transient) 300 VAC

(1500 V transient) Not applicable

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum 50 mA maximum 50 m A maximum

Module Ratings

Number of Channels Per

Module 4 4 4 4

Turn-on Time 100 usec 100 usec 100 usec 100 usec

Turn-off Time 750 usec 750 usec 750 usec 750 usec

Isolation (Field Side to

Logic Side) 4,000 volts (transient) 4,000 volts (transient) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 ° to 70 °C, operating

-30 ° to 85 °C, storage 0 ° to 70 °C, operating

-30 ° to 85 °C, storage

Agency Approvals UL, CE, RoHS, DFARS UL, CE, RoHS, DFARS UL, CE, RoHS, DFARS UL, CE, RoHS, DFARS

Warranty 30 months Lifetime Lifetime Lifetime

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

11

Specifications—DC Modules (continued)

SNAP-ODC5SRCFM SNAP-ODC5SNKFM

Key Feature Factory Mutual approved Factory Mutual approved

Field Side Ratings (each channel)

Line Voltage - Range 5–60 VDC 5–60 VDC

Line Voltage - Nominal 5–48 VDC 5–48 VDC

Current Rating 0°C to 70°C Ambi-

ent 3 amps per module 3 amps per module

Surge Current 5 amps peak for

1 second 5 amps peak for

1 second

Minimum Load 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps

Off-state Leakage 1 mA @ 60 VDC 1 mA @ 60 VDC

Peak Blocking Voltage 60 VDC 60 VDC

Fuse

(Common to all Channels)

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part No. BEL 5HF4

Opto 22 Part SNAP-4A

250 VAC - 4A 5x20 mm

Fast-acting Bell Fuse Part No. BEL 5HF4

Opto 22 Part SNAP-4A

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per Module 4 4

Turn-on Time 100 usec 100 usec

Turn-off Time 750 usec 750 usec

Isolation (Field Side to Logic Side) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 to 70 °C, operating

-30 to 85 °C, storage 0 to 70 °C, operating

-30 to 85 °C, storage

Agency Approvals CE, FM, RoHS, DFARS CE, FM, RoHS, DFARS

Warranty Lifetime Lifetime

* The power rating of the dry contact module must not exceed 10 VA under steady state or momentary in-rush conditions. For

voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the maximum allowable current is

determined by the following equation: 10 VA / Voltage = Current maximum. Rating curve is in the data sheet.

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

12

DATA SHEET

Form 1144-101029

Specifications—DC Modules (continued)

SNAP-ODC5RFM SNAP-ODC5R5FM

Key Feature Factory Mutual approved Factory Mutual approved

Field Side Ratings (each channel)

Line Voltage - Range 0–100 VDC

0–130 VAC* 0–100 VDC

0–130 VAC*

Line Voltage - Nominal -- --

Current Rating 0 °C to 70 °C

Ambient 0.5 amps switching* 0.5 amps switching*

Surge Current 0.5 amps* 0.5 amps*

Minimum Load 0 mA 0 mA

Output Voltage Drop 0 volts 0 volts

Off-state Leakage 0 mA 0 mA

Peak Blocking Voltage 100 VDC / 130 VAC 100 VDC / 130 VAC

Fuse

(Common to all Channels) Has four isolated channels. User

must provide own fusing. Has four isolated channels. User

must provide own fusing.

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per Module 4 4

Turn-on Time 500 usec 500 usec

Turn-off Time 500 usec 500 usec

Isolation (Field Side to Logic Side) 1,500 volts (transient) 1,500 volts (transient)

Mechanical Life 200,000,000 cycles 200,000,000 cycles

Temperature 0 to 70 °C, operating

-30 to 85 °C, storage 0 to 70 °C, operating

-30 to 85 °C, storage

Agency Approvals CE, FM, RoHS, DFARS CE, FM, RoHS, DFARS

Warranty 30 months or mechanical life, which-

ever comes first 30 months or mechanical life, which-

ever comes first

* The power rating of the dry contact module must not exceed 10 VA under steady state or momentary in-rush

conditions. For voltages at or below 20 volts, the current limit is 0.5 amps. For voltages above 20 volts, the max-

imum allowable current is determined by the following equation: 10 VA / Voltage = Current maximum. Rating

curve is in the data sheet.

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

13

Specifications—DC Modules (continued)

SNAP-ODC5-iFM SNAP-ODC5A-iFM

Key Feature Four isolated channels

Factory Mutual approved Four isolated channels

Factory Mutual approved

Field Side Ratings (each channel)

Line Voltage - Range 5–60 VDC 5–200 VDC

Line Voltage - Nominal 5–48 VDC 5–200 VDC

Current Rating 0°C to 70°C

Ambient 3 amps per module 3 amps per module

Surge Current 5 amps peak for 1 second 5 amps peak for 1 second

Minimum Load 20 mA 20 mA

Output Voltage Drop 1.6 volts max.@ 0.75 amps 1.6 volts max.@ 0.75 amps

Off-state Leakage 1 mA @ 60 VDC 1 mA @ 6 0 VDC

Peak Blocking Voltage 60 VDC 200 VDC

Fuse (Common to all Channels) Has four isolated channels.

User must provide own fusing. Has four isolated channels.

User must provide own fusing.

Logic Side Ratings

Pickup Voltage 4 V @ 5.5 mA 4 V @ 5.5 mA

Dropout Voltage 1 VDC 1 VDC

Control Resistance 220 ohms 220 ohms

Logic Supply Voltage 5 VDC ± 0.25 VDC 5 VDC ± 0.25 VDC

Logic Supply Current 50 mA maximum 50 mA maximum

Module Ratings

Number of Channels Per Module 4 4

Turn-on Time 100 usec 100 usec

Turn-off Time 750 usec 750 usec

Isolation (Field Side to Logic

Side) 4,000 volts (transient) 4,000 volts (transient)

Temperature 0 ° to 70 °C, operating

-30 ° to 85 °C, storage 0 ° to 70 °C, operating

-30 ° to 85 °C, storage

Agency Approvals CE, FM, RoHS, DFARS CE, FM, RoHS, DFARS

Warranty Lifetime Lifetime

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

14

DATA SHEET

Form 1144-101029

Schematics

SNAP-ODC5SRC Output Module—

Sourcing Part Number Description

SNAP-ODC5SRC 4-channel DC output 5–60 VDC logic source

SNAP-ODC5SRCFM 4-channel DC output 5–60 VDC logic source,

Factory Mutual approved

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

15

Schematics

SNAP-ODC5SNK and SNAP-ODC5ASNK

Output Modules—Sinking Part Number Description

SNAP-ODC5SNK 4-channel DC output 5–60 VDC logic sink

SNAP-ODC5SNKFM 4-channel DC output 5–60 VDC logic sink,

Factory Mutual approved

SNAP-ODC5ASNK 4-channel DC output 5–200 VDC logic sink

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

16

DATA SHEET

Form 1144-101029

Schematics

SNAP-ODC5R and SNAP-ODC5R5

Dry Contact Module Part Number Description

SNAP-ODC5R 4-channel dry contact output, normally open

SNAP-ODC5R5 4-channel dry contact output, normally closed

SNAP-ODC5RFM 4-channel dry contact output, normally open,

Factory Mutual approved

SNAP-ODC5R5FM 4-channel dry contact output, normally closed,

Factory Mutual approved

Current Limit at Key Voltages

VDC mA

5 500

12 500

24 416

48 206

1001100

1 Maximum DC voltage is 100 VDC.

10 VA Rating for Reed Relay (Dry Contact)Modules

600

500

400

300

200

100

00123456789100

Field Voltage

Maximum Allowable Peak Current (mA)

NOTE: Commutating diode* must be used on

inductive loads. Typical wiring examples:

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

17

Schematics

SNAP-ODC5MA Output Module with

Manual/Auto Switches Part Number Description

SNAP-ODC5MA 4-channel isolated DC output 5–60 VDC,

5 VDC logic, with manual/auto switches

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

18

DATA SHEET

Form 1144-101029

Schematics

SNAP-ODC5-i and SNAP-ODC5A-i

Isolated Output Module Part Number Description

SNAP-ODC5-i 4-channel isolated DC output 5–60 VDC, 5 VDC logic

SNAP-ODC5A-i 4-channel isolated DC output 5–200 VDC, 5 VDC logic

SNAP-ODC5-iFM 4-channel isolated DC output 5–60 VDC, 5 VDC logic,

Factory Mutual approved

SNAP-ODC5A-iFM 4-channel isolated DC output 5–200 VDC, 5 VDC

logic, Factory Mutual approved

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

19

Dimensional Drawing

All Models Except MA

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

20

DATA SHEET

Form 1144-101029

Dimensional Drawing

All MA Models

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules DATA SHEET

Form 1144-101029

PAGE

21

Dimensional Drawing

IMPORTANT: The mounting rack connector has 24 pins; the

module connector has 20 pins. The extra pins on the mounting

rack connector prevent misalignment of the module during

installation.

All Models

SNAP Digital Output Modules

Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • www.opto22.com

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

SNAP Digital Output Modules

PAGE

22

DATA SHEET

Form 1144-101029

Dimensional Drawing

SNAP Digital Module Mounted on SNAP Rack

All Models

More About Opto 22

www.opto22.com • Opto 22 • 43044 Business Park Drive • Temecula, CA 92590-3614 • Form 1335-090113

SALES 800-321-6786 • 951-695-3000 • FAX 951-695-3095 • sales@opto22.com • SUPPORT 800-835-6786 • 951-695-3080 • FAX 951-695-3017 • support@opto22.com

© 2010 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.

Products

Opto 22 develops and manufactures reliable, flexible, easy-to-use

hardware and software products for industrial automation, remote

monitoring, and data acquisition applications.

SNAP PAC System

Designed to simplify the typically complex process of

understanding, selecting, buying, and applying an automation

system, the SNAP PAC System

consists of four integrated

components:

•SNAP PAC controllers

•PAC Project™ Software Suite

•SNAP PAC brains

•SNAP I/O™

SNAP PAC Controllers

Programmable automation controllers

(PACs) are multifunctional, multidomain,

modular controllers based on open standards and

providing an integrated development environment.

Opto 22 has been manufacturing PACs for many years. The latest

models include the standalone SNAP PAC S-series and the rack-

mounted SNAP PAC R-series. Both handle a wide range of digital,

analog, and serial functions and are equally suited to data

collection, remote monitoring, process control, and discrete and

hybrid manufacturing.

SNAP PACs are based on open Ethernet and Internet Protocol (IP)

standards, so you can build or extend a system without the expense

and limitations of proprietary networks and protocols.

PAC Project Software Suite

Opto 22’s PAC Project Software Suite provides full-featured and

cost-effective control programming, HMI (human machine

interface) development and runtime, OPC server, and database

connectivity software to power your SNAP PAC System.

These fully integrated software applications share a single tagname

database, so the data points you configure in PAC Control™ are

immediately available for use in PAC Display™, OptoOPCServer™,

and OptoDataLink™. Commands are in plain English; variables and

I/O point names are fully descriptive.

PAC Project Basic offers control and HMI tools and is free for

download on our website, www.opto22.com. PAC Project

Professional, available for separate purchase, adds OptoOPCServer,

OptoDataLink, options for Ethernet link redundancy or segmented

networking, and support for legacy Opto 22 serial mistic™ I/O units.

SNAP PAC Brains

While SNAP PAC controllers provide central control and data

distribution, SNAP PAC brains provide distributed intelligence for

I/O processing and communications. Brains offer analog, digital,

and serial functions, including thermocouple linearization; PID loop

control; and optional high-speed digital counting (up to 20 kHz),

quadrature counting, TPO, and pulse generation and measurement.

SNAP I/O

I/O provides the local connection to sensors and equipment.

Opto 22 SNAP I/O offers 1 to 32 points of reliable I/O per module,

depending on the type of module and your needs. Analog,

digital, serial, and special-purpose modules are all mixed on

the same mounting rack and controlled by the same processor

(SNAP PAC brain or rack-mounted controller).

Quality

Founded in 1974 and with over 85 million devices sold,

Opto 22 has established a worldwide reputation for high-

quality products. All are made in the U.S.A. at our

manufacturing facility in Temecula, California. Because we

do no statistical testing and each part is tested twice before leaving

our factory, we can guarantee most solid-state relays and optically

isolated I/O modules for life.

Free Product Support

Opto 22’s Product Support Group offers free, comprehensive

technical support for Opto 22 products. Our staff of support

engineers represents decades of training and experience. Product

support is available in English and Spanish, by phone or email,

Monday through Friday, 7 a.m. to 5 p.m. PST.

Free Customer Training

Hands-on training classes for the SNAP PAC System are offered at

our headquarters in Temecula, California. Each student has his or

her own learning station; classes are limited to nine students.

Registration for the free training class is on a first-come, first-served

basis. See our website, www.opto22.com, for more information or

email training@opto22.com.

Purchasing Opto 22 Products

Opto 22 products are sold directly and through a worldwide

network of distributors, partners, and system integrators. For more

information, contact Opto 22 headquarters at 800-321-6786 or

951-695-3000, or visit our website at www.opto22.com.

www.opto22.com