123 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES Related Information General terms and conditions............. P.1 Glossary of terms / General precautions...P.983~ / P.986~ Sensor selection guide........P.11~ / P.61~ Fiber selection................................. P.63~ LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Conforming to EMC Directive AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS SUNX website http://www.sunx.com PNP output type available Timer Automatic sensitivity setting Test input Interference Light intensity monitor prevention STATIC CONTROL DEVICES LASER MARKERS Taking fiber sensors to the next level Setup is made simple, using a dual digital display Selection Guide Fibers The dual digital display allows users to check both the threshold value and incident light intensity at the same time, allowing for clear and intuitive control of the sensor's functions. The threshold value can be adjusted simply by pressing the (UP) key or the (DOWN) key, so that the output operation can be controlled with high precision, directly from the RUN mode. Threshold value Incident light intensity FT / FD / FR Fiber Fiber Sensor Sensor Amplifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products Commercially-available connectors are used so that lead time and spare part numbers can both be reduced The connectors used are commercially-available connectors, so that processing costs and lead time required for carrying out processing after purchase of the sensors can be greatly reduced. The same connection parts as the DP-100 series of digital pressure sensors and the PM-64 series of micro photoelectric sensors can be used. Connection with a commercially-available connector Commercially-available press-fit connectors are used, so that the processing costs for connection cables can be greatly reduced. Conventional (cable type) Conventional lead time Harness processing by outside order after sensor preparation Customer Sensor preparation 1 Sensor purchase and preparation 2 Harness processing by outside order Harness processor From now on (built-in connector type) Sensor installation Harness Processing Lead time from now on Harness processing by outside order Customer Sensor preparation 1 Sensor purchase and preparation 2 Harness processing by outside order Harness processor Using cables with connectors Sensor installation Harness Processing Lead time further reduced Customer Sensor preparation Sensor installation 1 Purchase of sensors and cable with connectors Reduced Reduced Reduced lead time Digital Fiber Sensor FX-100 SERIES ORDER GUIDE LIST OF FIBERS SPECIFICATIONS I/O CIRCUIT DIAGRAMS SENSING CHARACTERISTICS PRECAUTIONS FOR PROPER USE DIMENSIONS P.126~ P.128~ P.133 P.134~ P.135~ P.136~ P.138 Saving-space with a width of 9 mm 0.354 in Equipped with a four-chemical emitting element The sensor is very slim, yet equipped with a dual digital display. Both space saving and ease of use have been achieved. A stable amount of emitted light is ensured due to control of the aging of the emitting element to the maximum limit. [Stable sensing comparison] AREA SENSORS Long-term stability SAFETY COMPONENTS A three level navigation structure provides easy access to the sensor's functions, from basic to advanced Setting details are divided into three levels for simple operation, so that settings for normal operation are made in "RUN mode", basic settings are made in "SET mode", and advanced functions are set in "PRO mode". This makes configuration much easier to understand and carry out. Functions used during normal operation [Function table] * Changing threshold values * Key lock * Quick settings * Code settings SET mode Functions used when initializing the sensor and carrying out maintenance [Function table] SET MODE PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS RUN mode Simple setting LASER SENSORS MICRO PHOTOELECTRIC SENSORS Time RUN MODE FIBER SENSORS PHOTOELECTRIC SENSORS FX-100 Three-chemical emitting element Light-emitting amount 9 mm 0.354 in 124 WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS * Teaching * L-ON / D-ON setting * Timer setting * Attenuation function * Interference prevention function PRO mode Equipped with a full complement of digital fiber sensor functions PRO MODE [Function table] * Shift * External input * Reset * GETA * ECO * Display reversing * Surplus value display * Copy * Threshold tracking Special and detailed setting Selection Guide Fibers FT / FD / FR Quick code input function [RUN mode] Sensor settings can be made simply by selecting preset values. Fiber Sensor sensor Fiber Amplifiers Amplifiers Quick setting numbers (summary) No. FX-100 Output operation Light-emitting amount selection Timer Dark-ON OFF None FX-410 Dark-ON ON None FX-311 Dark-ON OFF OFF-delay 10 ms FX-11A Dark-ON ON OFF-delay 10 ms FX-301-F Light-ON ON ON-delay 40 ms Other Products Light-ON OFF ON-delay 40 ms Light-ON ON ON-delay 10 ms Light-ON OFF ON-delay 10 ms Smooth support via telephone [RUN mode] Confirmation can be carried out smoothly via telephone by simply quoting numbers. This can be of great assistance when dealing with foreign country customers. FX-300 125 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Digital Fiber Sensor FX-100 SERIES Teaching using ON / OFF buttons [SET mode] Attenuation function [SET mode] Simply press the ON button when an object is present and OFF when it is not. There is no need to switch settings or make judgments between Light-ON ( ) and Dark-ON ( ). If the light receiving level becomes saturated when sensing over short distances or when sensing transparent objects or minute objects, the light emitting amount can be reduced so that stable sensing can be provided without needing to change the response time. Interference prevention function [SET mode] Thru-beam type / Retroreflective type AREA SENSORS FX-101: Interference prevention for up to 3 units FX-102: Interference prevention for up to 4 units SAFETY COMPONENTS PRESSURE SENSORS Object present ON The emission frequencies can be set separately for each unit in order to avoid interference. The emitted light flashes while setting is in progress, so that you can see at a glance which fiber sensor is currently being set. In addition, this interference prevention is not done by using optical communication. This means that there is no need to place the amplifiers close together like there was before, and so the amplifiers can be set up apart from each other. Object absent OFF INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Reflective type SENSOR OPTIONS * When the emission frequencies are changed, the response times will also change. WIRE-SAVING SYSTEMS MEASUREMENT SENSORS Object present ON Object absent OFF STATIC CONTROL DEVICES LASER MARKERS Limit teaching function This carries out teaching and sets threshold values only when no object is present (when the incident light amount is stable). This is useful when sensing objects if there are other objects in the background and when sensing minute objects. Teaching can also be carried out using external input. FT / FD / FR Fiber Fiber Sensor Sensor Amplifiers Amplifi ers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products Threshold tracking function [PRO mode] This function seeks changes in the light emitting amount resulting from changes in the environment over long periods (such as dust levels), so that the incident light intensity can be checked at desired intervals and the threshold values can be reset automatically. Current value The amount of light received when there is no object Settings such as emission halt, limit / auto teaching and ECO settings can be carried out via external input. (Brown) +V (Black) Output (White) External input (Blue) 0 V External input lines are equipped as standard Alert function [PRO mode] When the amount light received approaches the threshold value, the display can be made to blink in order to alert the operator. Threshold value Time GETA function [PRO mode] The display value for the incident light intensity can be offset by the desired value (target value). The target value can be set to between 0 and 2,000 (in increments of 100). For example, if the incident light intensity is 1,500 and the target value is set to 2,000, then "2,000" will appear in the digital display. Variations in the amount of light received Multi-function external input [PRO mode] The amount of light received ranges from about 900 to 1,100 when the digital indicator flashes. Incident light intensity Fibers Incident light intensity Selection Guide The emitted light and output indicator flash at the same frequency. Range of the digital indicator flashing (margin: small) 1,100 approx. 900 approx. The digital indicator flashes. Unify at 500 using the GETA function Threshold value of 1,000 Digital Fiber Sensor FX-100 SERIES ORDER GUIDE FIBER SENSORS Amplifiers Appearance M8 plug-in connector type Cable set (Note 1) Standard type M8 plug-in connector type Type M8 plug-in connector type M8 plug-in connector type Cable set (Note 1) LASER SENSORS Accessory Emitting element Model No. Output FX-101 (Note 2) NPN open-collector transistor FX-101-Z (Note 3) NPN open-collector transistor FX-101P (Note 2) PNP open-collector transistor FX-101P-Z (Note 3) PNP open-collector transistor FX-101-CC2 NPN open-collector transistor FX-101P-CC2 PNP open-collector collector transistor Red LED Long sensing range type 126 FX-102 (Note 2) NPN open-collector transistor FX-102-Z (Note 3) NPN open-collector transistor FX-102P (Note 2) PNP open-collector transistor FX-102P-Z (Note 3) PNP open-collector transistor FX-102-CC2 NPN open-collector transistor FX-102P-CC2 PNP open-collector transistor PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS * CN-14A-C2 Connector attached cable 2 m 6.562 ft * Only include cable set type AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Notes: 1) The connector attached cable CN-14A-C2 is supplied with the amplifier. 2) Make sure to use the optional connector attached cable CN-14A(-R)-C or the connector CN-14A, or a connector manufactured by J.S.T. Mfg. Co., Ltd. (contact: SPHD-001T-P0.5, housing: PAP-04V-S) 3) Make sure to use the optional M8 connector attached cable CN-24A-C. OPTIONS M8 connector attached cable Designation Model No. CN-14A-C1 Connector attached cable Description 31.4 1.236 1 m 3.281 ft 3 m 9.843 ft CN-14A-C5 5 m 16.404 ft CN-14A-R-C1 1 m 3.281 ft CN-14A-R-C2 2 m 6.562 ft CN-14A-R-C3 3 m 9.843 ft CN-14A-R-C5 5 m 16.404 ft M8 connector attached cable CN-24A-C2 2 m 6.562 ft CN-24A-C5 5 m 16.404 ft Connector CN-14A Set of 10 housings and 40 contacts 0.02 mm2 4-core cabtyre cable with connector on one end Cable outer diameter: o3.7 mm o0.146 in FX-100 FX-300 FX-311 Fixing ring FX-11A For M8 plug-in connector type The connector on one end Cable outer diameter: o4 mm o0.157 in This protects the operating surfaces. Amplifier MS-DIN-4 mounting bracket Mounting bracket for amplifier MS-DIN-E Fiber Fiber Sensor Sensor Amplifi ers Amplifiers FX-410 Protection cover FC-FX-1 End plates FT / FD / FR M8 connector attached cable CN-24A-C o9 o0.354 Selection Guide Fibers o4 o0.157 CN-14A-C2 (Note) 2 m 6.562 ft CN-14A-C3 Connector attached cable (Flexible type) * CN-24A-C Protection cover Other Products * FC-FX-1 When it moves depending on the way it is installed on a DIN rail, these end plates ensure that all amplifiers are mounted together in a secure and fully connected manner. Two pcs.per set Amplifier mounting bracket Note: The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10(P)-CC2. Recommended connector Contact: SPHD-001T-P0.5, Housing: PAP-04V-S (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. * MS-DIN-4 Connector attached cable Connector * CN-14A * CN-14A(-R)-C Contact Recommended crimping tool Model No.: YC-610R (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Housing FX-301-F 127 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS LASER SENSORS Thru-beam type (one pair set) PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to p.63~ "Fiber Selection" for details of each fiber. AREA SENSORS FT-A8 Model No. FT-A30 SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS FT-AFM2 FT-AFM2E Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-100 1,500 59.055 3,500 137.795 (Note 2) P.106 FT-PS1 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) 280 11.024 Sensing range (mm in) (Note 1) Standard type FX-101 Long sensing range type FX-102 Dimensions 40 1.575 90 3.543 P.109 P.106 FT-R80 180 7.087 430 16.929 P.109 720 28.346 P.106 FT-SFM2 300 11.811 800 31.496 P.109 760 29.921 2,400 94.488 P.109 470 18.504 P.109 280 11.024 P.109 670 26.378 P.106 FT-SFM2L 1,150 45.276 P.106 FT-SFM2SV2 180 7.087 FT-E12 6 0.236 19 0.748 P.106 FT-SNFM2 130 5.118 FT-E22 15 0.591 60 2.362 P.106 FT-T80 300 11.811 800 31.496 P.109 P.106 FT-V10 1,000 39.370 2,350 92.520 P.109 P.106 FT-V22 140 5.512 380 14.961 P.109 P.106 FT-V41 40 1.575 120 4.724 P.109 340 13.386 800 31.496 P.109 80 3.150 220 8.661 P.109 260 10.236 FT-B8 FT-FM2 FT-FM2S 300 11.811 800 31.496 FT-FM2S4 FT-FM10L 9,300 366.141 15,000 590.550 P.106 FT-V80Y 250 9.843 700 27.559 P.106 FT-W4 P.107 FT-W8 135 5.315 420 16.535 P.107 FT-WA8 P.107 FT-WA30 210 8.268 540 21.260 P.107 150 5.906 500 19.685 FT-H20W-M1 100 3.937 300 11.811 FT-H30-M1V-S (Note 4) 110 4.331 280 11.024 FT-H13-FM2 FT-H20-J20-S (Note 3) FT-H20-J30-S (Note 3) FT-H20-J50-S (Note 3) FT-H20-M1 FT-H35-M2 FT / FD / FR Model No. 240 9.449 FT-H20-VJ80-S (Note 3) Fibers Standard type FX-101 Long sensing range type FX-102 Dimensions 400 15.748 FT-H20-VJ50-S (Note 3) Selection Guide Sensing range (mm in) (Note 1) FT-H35-M2S6 FT-HL80Y FT-K8 650 25.591 P.110 1,500 59.055 3,500 137.795 (Note 2) P.110 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) P.110 FT-WKV8 700 27.559 2,200 86.614 P.110 P.107 FT-WR80 215 8.465 570 22.441 P.110 P.107 FT-WR80L 430 16.929 1,150 45.276 P.110 P.107 FT-WS3 150 5.906 600 23.622 P.110 P.107 FT-WS4 80 3.150 220 8.661 P.110 P.107 FT-WS8 260 10.236 650 25.591 P.110 170 6.693 490 19.291 P.107 FT-WS8L 600 23.622 1,500 59.055 P.110 990 38.976 2,340 92.126 P.107 FT-WV42 30 1.181 80 3.150 P.110 230 9.055 670 26.378 P.110 80 3.150 230 9.055 P.111 330 12.992 1,000 39.370 P.111 190 7.480 580 22.835 P.111 1,000 39.370 3,000 118.110 P.108 FT-WZ4 FT-KV1 135 5.315 500 19.685 P.108 FT-WZ4HB FT-KV8 1,000 39.370 3,000 118.110 P.108 FT-WZ7 FT-L80Y 1,100 43.307 2,600 102.362 P.108 FT-WZ7HB P.108 FT-WZ8 330 12.992 950 37.402 P.111 130 5.118 280 11.024 P.108 FT-WZ8E 700 27.559 2,100 82.677 P.111 P.108 FT-WZ8H 1,200 47.244 2,800 110.236 P.111 FX-300 FT-NFM2 FX-410 FT-NFM2S FX-311 FT-NFM2S4 FX-11A FT-P2 120 4.724 330 12.992 P.108 FT-Z8 360 14.173 1,000 39.370 P.111 FX-301-F FT-P40 80 3.150 240 9.449 P.108 FT-Z8E 800 31.496 1,850 72.835 P.111 FT-P60 130 5.118 300 11.811 P.108 FT-Z8H 1,400 55.118 3,100 122.047 P.111 FT-P80 230 9.055 650 25.591 P.108 FT-Z802Y 520 20.472 3,100 122.047 P.111 260 10.236 800 31.496 P.108 Other Products FT-P81X Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long. 3) Heat-resistant joint fibers and ordinary-temperature side fibers (FT-FM2) are sold as a set. Please refer to p.93~ for details. 4) Sold as a set comprising vacuum-resistant type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). Please refer to p.91~ for details. Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS 128 FIBER SENSORS Retroreflective type LASER SENSORS Fibers are listed in alphabetic order. Refer to p.63~ "Fiber Selection" for details of each fiber. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Model No. FR-KV1 Sensing range (mm in) (Note 1, 2) Standard type FX-101 Long sensing range type FX-102 Dimensions 15 to 200 0.591 to 7.874 15 to 360 0.591 to 14.173 P.112 FR-KZ21 200 7.874 200 7.874 P.112 FR-KZ21E 200 7.874 200 7.874 P.112 100 to 550 3.937 to 21.654 100 to 830 3.937 to 32.677 P.112 FR-WKZ11 AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. The sensing range of FR-WKZ11 is specified for the RF-13. The sensing range of FR-KZ21, FR-KZ21E and FR-KV1 is specified for the attached reflector. The sensing ranges when using in combination with the FR-WKZ11 reflector (optional) are given in the below table. Amplifier FX-101 FX-102 100 to 700 3.937 to 27.559 100 to 1,100 3.937 to 43.307 FR-WKZ11 + RF-220 100 to 1,300 3.937 to 51.181 100 to 2,600 3.937 to 102.362 FR-WKZ11 + RF-230 100 to 2,000 3.937 to 78.740 100 to 4,000 3.937 to 157.480 Reflector FR-WKZ11 + RF-210 INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS 2) The sensing range of FR-WKZ11 is the possible setting range for the reflector or reflective tape. The fiber can detect an object less than 100 mm 3.937 in away. However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs, adjust the threshold value of the amplifier unit before use. The sensing range of FR-KZ21(E) is the possible setting range for the reflector. However, if setting the fiber to detect objects passing within 0 to 20 mm 0 to 0.787 in from the fiber head, unstable detection may result. The sensing range of FR-KV1 is the possible setting range for the reflector. The fiber can detect an object less than 15 mm 0.591 in away. WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Reflective type Fibers are listed in alphabetic order. Refer to "Fiber Selection p.63~" for details of each fiber. Model No. Sensing range (mm in) (Note 1, 2) Standard type FX-101 Long sensing range type FX-102 Dimensions Model No. Sensing range (mm in) (Note 1, 2) Standard type FX-101 Long sensing range type FX-102 Dimensions FD-A15 125 4.921 250 9.843 P.113 FD-G6 50 1.969 120 4.724 P.114 FD-AFM2 105 4.134 285 11.220 P.113 FD-G6X 45 1.772 160 6.299 P.114 85 3.346 245 9.646 P.113 FD-H13-FM2 100 3.937 280 11.024 P.114 FD-B8 170 6.693 440 17.323 P.113 FD-H18-L31 FD-E12 3.5 0.138 13 0.512 P.113 FD-H20-21 90 3.543 280 11.024 P.115 FD-E22 16 0.630 45 1.772 P.113 FD-H20-M1 120 4.724 300 11.811 P.115 FD-EG1 18 0.709 50 1.969 P.113 FD-H30-KZ1V-S (Note 3) 25 to 80 0.984 to 3.150 10 to 220 0.394 to 8.661 P.115 FD-EG2 10 0.394 30 1.181 P.113 FD-H30-L32 2 to 9 0.079 to 0.354 0 to 17 0 to 0.669 P.115 FD-EG3 7 0.276 22 0.866 P.113 FD-H30-L32V-S (Note 3) 2.5 to 6.5 0.098 to 0.256 0 to 11 0 to 0.433 P.115 FD-EN500S1 1 0.039 4 0.157 P.113 FD-H35-20S FD-ENM1S1 15 0.591 48 1.890 P.114 FD-H35-M2 FD-AFM2E FD-F4 FD-F41 FD-F8Y FD-FM2 FD-FM2S FD-FM2S4 FD-G4 Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in] FD-H35-M2S6 P.114 P.116 FD-L43 0 to 19 0 to 0.748 0 to 25 0 to 0.984 P.116 FD-L44 0 to 6 0 to 0.236 0 to 8 0 to 0.315 P.116 FD-L44S 0 to 4.5 0 to 0.177 0 to 5.5 0 to 0.217 P.116 FD-L45 0 to 40 0 to 1.575 0 to 50 0 to 1.969 P.116 16 to 30 0.630 to 1.181 12 to 50 0.472 to 1.969 P.116 FD-L46 FD-NFM2 P.114 FD-NFM2S P.114 FD-NFM2S4 P.114 FD-P2 120 4.724 P.116 3 to 14 0.118 to 0.551 1.5 to 16 0.059 to 0.630 (Convergent point 8 0.315) (Convergent point 8 0.315) P.114 50 1.969 P.116 FD-L41 P.114 345 13.583 280 11.024 P.116 P.116 - 100 3.937 75 2.953 200 7.874 P.115 5 to 8 0.197 to 0.315 1 to 17 0.039 to 0.669 (Convergent point 6 0.236) (Convergent point 6 0.236) P.114 410 16.142 85 3.346 0 to 25 0 to 0.984 FD-L4 Applicable pipe diameter: Outer dia. o6 to o26 mm o0.236 to o1.024 in transparent pipe [PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in] 100 3.937 0 to 10 0 to 0.394 P.117 35 1.378 100 3.937 P.117 P.117 25 0.984 65 2.559 P.117 Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fibers. Refer to p.71~ for details. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) Sold as a set comprising vacuum-resistant type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). Please refer to p.91~ for details. Selection Guide Fibers FT / FD / FR Fiber Fiber Sensor Sensor Amplifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products 129 FIBER SENSORS Digital Fiber Sensor FX-100 SERIES LIST OF FIBERS LASER SENSORS Reflective type PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Fibers are listed in alphabetic order. Refer to "Fiber Selection p.63~" for details of each fiber. AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Selection Guide Fibers FT / FD / FR Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products Model No. Sensing range (mm in) (Note 1, 2) Standard type FX-101 Long sensing range type FX-102 Dimensions Model No. FD-P40 8 0.315 30 1.181 P.117 FD-WG4 FD-P50 45 1.772 150 5.906 P.117 FD-P60 45 1.772 150 5.906 P.117 FD-P80 90 3.543 200 7.874 P.117 FD-P81X 70 2.756 220 8.661 P.117 FD-R80 70 2.756 180 7.087 P.117 FD-S80 100 3.937 345 13.583 P.117 FD-SFM2SV2 30 1.181 90 3.543 P.117 FD-SNFM2 35 1.378 100 3.937 P.118 FD-T40 35 1.378 100 3.937 P.118 FD-T80 100 3.937 345 13.583 P.118 FD-V41 25 0.984 70 2.756 P.118 FD-W8 80 3.150 230 9.055 P.118 FD-W44 15 0.591 40 1.575 P.118 Sensing range (mm in) (Note 1, 2) Standard type FX-101 Long sensing range type FX-102 28 1.102 75 2.953 Dimensions P.118 FD-WKZ1 20 to 180 0.787 to 7.087 20 to 480 0.787 to 18.898 P.118 FD-WL41 7 to 12 0.276 to 0.472 6 to 13.5 0.236 to 0.531 (Convergent point 8 0.315) (Convergent point 8 0.315) P.118 FD-WL48 1 to 4.5 0.039 to 0.177 0.5 to 6.5 0.020 to 0.256 P.119 FD-WS8 80 3.150 230 9.055 P.119 FD-WSG4 28 1.102 75 2.953 P.119 FD-WT4 15 0.591 40 1.575 P.119 FD-WT8 80 3.150 230 9.055 P.119 6 0.236 20 0.787 P.119 FD-WV42 FD-WZ4 FD-WZ4HB 2 to 20 0.079 to 0.787 1 to 70 0.039 to 2.756 FD-WZ7 1 to 55 0.039 to 2.165 FD-WZ7HB 1 to 60 0.039 to 2.362 0.5 to 180 0.020 to 7.087 160 6.299 P.119 P.119 P.119 P.119 Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fibers. Refer to p.71~ for details. 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut. 3) Sold as a set comprising vacuum-resistant type fiber + photo-terminal (FV-BR1) + fiber at atmospheric side (FT-J8). Please refer to p.91~ for details. Digital Fiber Sensor FX-100 SERIES 130 FIBER OPTIONS FIBER SENSORS Lens (For thru-beam type fiber) Designation The dimensions are on p.120~. Model No. Description Sensing range (mm in) [Lens on both sides] Fiber Increases the sensing range by 5 times or more. Expansion lens (Note 1) FX-LE1 * Ambient temperature: -60 to +350 C -76 to +662 F (Note 3) Amplifier FX-101 FX-102 FT-B8 2,200 86.614 3,500 137.795 (Note 2) FT-FM2, FT-T80 3,000 118.110 3,500 137.795 (Note 2) FT-R80 1,900 74.803 3,500 137.795 (Note 2) FT-W8 3,000 118.110 3,500 137.795 (Note 2) FT-P80, FT-P60 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) FT-P81X 1,600 62.992 (Note 2) 1,600 62.992 (Note 2) FT-H35-M2 2,000 78.740 3,500 137.795 (Note 2) FT-H20W-M1 1,300 51.181 1,600 62.992 (Note 2) FT-H20-M1 1,600 62.992 (Note 2) 1,600 62.992 (Note 2) FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S 1,000 39.370 3,500 137.795 (Note 2) LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS For thru-beam type fiber Sensing range (mm in) [Lens on both sides] Superexpansion lens (Note 1) FX-LE2 Amplifier FX-101 FX-102 Tremendously increases the sensing range with large diameter lenses. Fiber FT-P81X 1,600 62.992 (Note 2) 1,600 62.992 (Note 2) * Ambient temperature: -60 to +350 C -76 to +662 F (Note 3) FT-H35-M2 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) FT-B8, FT-FM2, FT-R80, FT-W8, FT-P80, FT-P60 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) FT-H20W-M1, FT-H20-M1 1,600 62.992 (Note 2) 1,600 62.992 (Note 2) 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) FT-H13-FM2 FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S 3,500 137.795 (Note 2) 3,500 137.795 (Note 2) WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Sensing range (mm in) [Lens on both sides] Side-view lens FX-SV1 Amplifier FX-101 FX-102 FT-B8 530 20.866 1,450 57.087 Fiber FT-FM2, FT-T80 550 21.654 1,700 66.929 Beam axis is bent by 90. FT-W8 450 17.717 1,300 51.181 * Ambient temperature: -60 to +300 C -76 to +572 F (Note 3) FT-P80 420 16.535 1,400 55.118 FT-P60 300 11.811 850 33.465 FT-P81X 550 21.654 1,700 66.929 FT-H35-M2 280 11.024 800 31.496 FT-H20W-M1 FT-H20-M1 FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S Expansion lens for vacuumresistant fiber (Note 1) Side-view lens for vacuumresistant fiber FV-LE1 FV-SV2 140 5.512 400 15.748 FT / FD / FR 840 33.071 150 5.906 410 16.142 Fiber Fiber Sensor Sensor Amplifi ers Amplifiers Sensing range (mm in) [Lens on both sides] (Note 4) Fiber * Ambient temperature: -60 to +300 C -76 to +572 F FT-H30-M1V (Note 3) Amplifier Fibers 280 11.024 Sensing range increases by Sensing range (mm in) [Lens on both sides] (Note 4) 4 times or more. Amplifier FX-101 FX-102 Fiber * Ambient temperature: -60 to +350 C -76 to +662 F FT-H30-M1V 450 17.717 1,600 62.992 (Note 3) Beam axis is bent by 90. Selection Guide FX-100 FX-300 FX-410 FX-311 FX-11A FX-101 FX-102 FX-301-F 450 17.717 1,600 62.992 Other Products Notes: 1) Be careful when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. Especially when installing a fiber with many cores (sharp bending fibers and heat-resistant glass fiber), please be sure to use it only after you have adjusted it sufficiently. 2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long (FT-H20W-M1, FT-P81X and FT-H20-M1: 1,600 mm 62.992 in). 3) For details on the ambient temperatures for the fibers which being combined, refer to p.101~. 4) The fiber cable length for the FT-H30-M1V is 1 m 3.281 ft. The sensing ranges in FX-102 (long sensing range type) take into account the length of the FT-J8 atmospheric side fiber. 131 Digital Fiber Sensor FIBER OPTIONS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS FX-100 SERIES Lens (For reflective type fiber) Designation Pinpoint spot lens AREA SENSORS The dimensions are on p.121~. Model No. Description Pinpoint spot of o0.5 mm o0.020 in. Enables detection of minute objects or small marks. * Distance to focal point: 6 1 mm 0.236 0.039 in * Applicable fibers: FD-WG4, FD-G4 * Ambient temperature: -40 to +70 C -40 to +158 F (Note 2) FX-MR1 Sensing range for FX-101 (mm in) (Note 1) SAFETY COMPONENTS The spot diameter is adjustable from o0.7 to o2 mm o0.028 to o0.079 in according to how much the fiber is screwed in. * Applicable fibers: FD-WG4, FD-G4 * Ambient temperature: -40 to +70 C Spot -40 to +158 F (Note 2) diameter * Accessory: MS-EX-3 (mounting bracket) Screw-in depth PRESSURE SENSORS Zoom lens INDUCTIVE PROXIMITY SENSORS FX-MR2 Distance to focal point PARTICULAR USE SENSORS For reflective type fiber LASER MARKERS Finest spot lens Extremely fine spot of o0.3 mm o0.012 in approx. achieved. * Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 * Ambient temperature: -40 to +70 C -40 to +158 F (Note 2) FX-MR3 Distance to focal point Finest spot lens Extremely fine spot of o0.1 mm o0.004 in approx. achieved. * Applicable fibers: FD-WG4, FD-G4, FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6 * Ambient temperature: -20 to +60 C -4 to +140 F (Note 2) FX-MR6 Fibers FT / FD / FR Screw-in depth FX-100 FX-311 FX-301-F Other Products o1.2 o0.047 14 mm 0.551 in 43 1.693 approx. o2.0 o0.079 FD-EG3 7.5 0.5 o0.15 o0.006 0.295 0.020 approx. FD-EG2 7.5 0.5 o0.2 o0.008 0.295 0.020 approx. FD-EG1 7.5 0.5 o0.3 o0.012 0.295 0.020 approx. FD-WG4/G4, FD-G6X/G6 7.5 0.5 o0.5 o0.020 0.295 0.020 approx. FD-EG3 7 0.5 o0.1 o0.004 0.276 0.020 approx. FD-EG2 7 0.5 o0.15 o0.006 0.276 0.020 approx. FD-EG1 7 0.5 o0.2 o0.008 0.276 0.020 approx. FD-WG4/G4, FD-G6X/G6 7 0.5 o0.4 o0.016 0.276 0.020 approx. Sensing range for FX-101 (mm in) (Note 1) Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-11A 27 1.063 approx. Fiber model No. Distance to focal point Spot diameter Selection Guide FX-410 12 mm 0.472 in Sensing range for FX-101 (mm in) (Note 1) Spot diameter FX-300 o0.7 o0.028 Fiber model No. Distance to focal point Spot diameter WIRESAVING SYSTEMS STATIC CONTROL DEVICES 18.5 0.728 approx. 7 mm 0.276 in Sensing range for FX-101 (mm in) (Note 1) SENSOR OPTIONS MEASUREMENT SENSORS Screw-in depth Distance to focal point Spot diameter Zoom lens Side-view type FX-MR5 Distance to focal point Spot diameter Screw-in depth Distance to focal point Spot diameter FX-MR2 is converted into a side-view type and can be mounted in a very small space. * Applicable fibers: FD-WG4, FD-G4 * Ambient temperature: -40 to +70 C -40 to +158 F (Note 2) 8 mm 0.315 in 13 0.512 approx. o0.5 o0.020 10 mm 0.394 in 15 0.591 approx. o0.8 o0.031 14 mm 0.551 in 30 1.181 approx. o3.0 o0.118 Notes: 1) The sensing ranges are the values when used in combination with FX-101 (standard type). Please contact our office for details on sensing ranges for other types of amplifier. 2) For details on the ambient temperatures for the fibers which being combined, refer to p.101~. Digital Fiber Sensor SPECIFICATIONS Standard type Model No. Long sensing range type Cable set Cable set NPN output FX-101(-Z) (Note 4) FX-101-CC2 PNP output FX-101P(-Z) (Note 4) FX-101P-CC2 Supply voltage Power consumption Output 12 to 24 V DC 10 % NPN non-contact input * Signal condition High: +8 V to +V DC or Open Low: 0 to +2 V DC (Source current 0.5 mA or less) * Input impedance: 10 k approx. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS 4 digits (green) + 4 digits (red) LCD display Incorporated ON-delay / OFF-delay timer, switchable either effective or ineffective [Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms] Incorporated Switchable either effective or ineffective Attenuation function Incorporated Emission frequency selection method (Note 2) (Functions at emission frequency 1, 2 or 3) Incorporated Emission frequency selection method (Note 2) (Functions at emission frequency 1, 2, 3 or 4) Selection Guide Fibers FT / FD / FR -10 to +55 C +14 to +131 F (If 4 to 7 units are mounted close together: -10 to +50 C +14 to +122 F, if 8 to 16 units are mounted close together: -10 to +45 C +14 to +113 F) (No dew condensation or icing allowed), Storage: -20 to +70 C -4 to +158 F Fiber Fiber Sensor Sensor Amplifi ers Amplifiers Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH FX-100 Incandescent light: 3,000 x at the light-receiving face FX-300 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3) FX-410 Ambient illuminance Insulation resistance 20 M, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3) Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each Shock resistance 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each Emitting element (modulated) Red LED (Peak emission wavelength: 632 nm 0.025 mil) Material Connector (Note 4) Cable length FX-311 FX-11A FX-301-F Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT Connecting method Accessory LASER SENSORS Orange LED (lights up when the output is ON) Timer function Environmental resistance Emission frequency 1: 2.5 ms or less (factory default setting) Emission frequency 2: 2.8 ms or less Emission frequency 3: 3.2 ms or less Emission frequency 4: 5.0 ms or less 2-level teaching / Limit teaching / Full-auto teaching Fine sensitivity adjustment function Weight FIBER SENSORS PARTICULAR USE SENSORS PNP non-contact input * Signal condition High: +4 V to +V DC (Sink current 0.5 to 3 mA) Low: 0 to +0.6 V DC or Open * Input impedance: 10 k approx. Emission frequency 0: 250 s or less (factory default setting) Emission frequency 1: 450 s or less Emission frequency 2: 500 s or less Emission frequency 3: 600 s or less Digital display Voltage withstandability FX-102P-CC2 Incorporated Operation indicator Ambient temperature FX-102P(-Z) (Note 4) Ripple P-P 10 % or less Selectable either Light-ON or Dark-ON, at SET mode Sensitivity setting Interference prevention function FX-102-CC2 NPN open-collector transistor PNP open-collector transistor * Maximum sink current: 100 mA * Maximum source current: 100 mA * Applied voltage: 30 V DC or less (between output and 0 V) * Applied voltage: 30 V DC or less (between output and +V) * Residual voltage: 1.5 V or less (at 100 mA sink current) * Residual voltage: 1.5 V or less (at 100 mA source current) Short-circuit protection Response time FX-102(-Z) (Note 4) Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage) ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage) Output operation External input 132 Refer to p.101~ for fiber specifications. Type Item FX-100 SERIES Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable. Net weight: 15 g approx. Gross weight: 35 g approx. Net weight: 15 g approx. Gross weight: 75 g approx. Net weight: 15 g approx. Gross weight: 35 g approx. Net weight: 15 g approx. Gross weight: 75 g approx. - CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1pc. - CN-14A-C2 (Connector attached cable, 2 m 6.562 ft long): 1pc. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 C +73.4 F. 2) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention function to different frequency values. However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2. 3) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. 4) Connector attached cable CN-14A-C2 is not attached to the models that have no "-CC2" at the end of the model Nos. Make sure to use the optional connector attached cable CN-14A(-R)-C or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd. (contact: SPHD-001T-P0.5, housing: PAP-04V-S). Model Nos. having the suffix "-Z" are M8 plug-in connector type. Make sure to use the optional M8 attached connector cable CN-24A-C. Other Products 133 Digital Fiber Sensor I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS FX-10(-Z/-CC2) NPN output type I/O circuit diagram Terminal arrangement diagram Color code of cable with connector 1 Sensor circuit PRESSURE SENSORS 2 Tr +8 V (Black) Output Load + - 100 mA max. ZD 3 4 INDUCTIVE PROXIMITY SENSORS WIRESAVING SYSTEMS Terminal No. (Brown) +V D SAFETY COMPONENTS SENSOR OPTIONS Connector type Terminal No. AREA SENSORS PARTICULAR USE SENSORS FX-100 SERIES (White) Extemal input 12 to 24 V DC 10 % 1 1 +V 2 2 Output 3 3 External input 4 0V Terminal No. Function 1 +V 2 Output 3 External input 4 0V 4 *1 (Blue) 0 V Internal circuit Function Users' circuit M8 plug-in connector type Symbols ... D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor *1 1 2 Non-voltage contact or NPN open-collector transistor MEASUREMENT SENSORS or STATIC CONTROL DEVICES High (+8 V to +V DC, or open): Ineffective Low [(0 to +2 V DC (source current 0.5 mA or less)]: Effective 3 4 LASER MARKERS FX-10P(-Z/-CC2) PNP output type I/O circuit diagram Terminal arrangement diagram Connector type Terminal No. Color code of cable with connector Terminal No. Function 1 1 +V 2 2 Output 3 3 External input 4 0V Terminal No. Function (Brown) +V Sensor circuit *1 Selection Guide Fibers FT / FD / FR 3 ZD Tr 100 mA max. 2 D 4 Fiber Sensor sensor Fiber Ampilifi ers Amplifiers (White) External input (Black) Output (Blue) 0 V Internal circuit Load FX-410 FX-301-F Other Products 4 M8 plug-in connector type Symbols ... D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor FX-311 FX-11A 12 to 24 V DC 10 % Users' circuit FX-100 FX-300 + - 1 *1 Non-voltage contact or PNP open-collector transistor 3 or High [ +4 V to +V DC (sink current 0.5 to 3 mA)]: Effective Low (0 to +0.6 V DC, or open): Ineffective 1 +V 2 Output 3 External input 4 0V 2 4 SENSING CHARACTERISTICS (TYPICAL) FT-A8 * Horizontal direction FT-B8 FT-FM2 FT-FM2S FT-FM2S4 Thru-beam type FT-SFM2 FT-T80 Thru-beam type Parallel deviation Parallel deviation 1,000 39.370 3,000 118.11 2,000 78.74 FX-101 Fiber head 1,000 39.37 8 mm 0.315 in approx. L 2,000 78.74 Fiber head 1,000 39.37 L 1,000 39.370 FX-102 FX-101 Fiber head 500 19.685 L Fiber head Fiber head Fiber head 0 200 100 0 100 200 7.874 3.937 3.937 7.874 Down Center Up Operating point (mm in) 0 200 7.874 FT-NFM2 FT-NFM2S Thru-beam FT-NFM2S4 FT-SNFM2 type Parallel deviation FX-101 0 1,000 39.37 100 0 100 200 3.937 3.937 7.874 Left Center Right Operating point (mm in) FT-P81X FX-101 100 3.937 L FX-101 500 19.685 L Fiber head 0 400 15.748 100 100 200 3.937 3.937 7.874 Left Center Right Operating point (mm in) FD-B8 Sensing field Fiber head L 0 100 3.937 200 0 200 400 7.874 7.874 15.748 Left Center Right Operating point (mm in) White non-glossy paper L Fiber head 0 100 3.937 50 0 50 100 1.969 1.969 3.937 Left Center Right Operating point (mm in) FD-NFM2 FD-NFM2S FD-NFM2S4 Reflective type FD-SNFM2 FD-T40 Sensing field FX-101 200 7.874 White non-glossy paper L Fiber head Setting distance L (mm in) FX-101 200 7.874 0 100 3.937 Setting distance L (mm in) Setting distance L (mm in) FX-102 50 1.969 White non-glossy paper L Fiber head Selection Guide Fibers FT / FD / FR 150 5.906 Fiber Fiber Sensor Sensor Amplifi ers Amplifiers 100 3.937 50 1.969 0 40 1.575 20 0 20 40 0.787 0.787 1.575 Left Center Right Operating point (mm in) Sensing field FX-102 FX-100 FX-101 White non-glossy paper L Fiber head FX-300 FX-410 FX-311 20 0 20 40 0.787 0.787 1.575 FX-11A Left Center Right Operating point (mm in) FX-301-F FD-WG4 FD-WSG4 Reflective type Other Products Sensing field 10 0 10 20 0.394 0.394 0.787 Left Center Right Operating point (mm in) FX-102 FX-101 100 3.937 0 40 1.575 White non-glossy paper L Fiber head 20 0 20 40 0.787 0.787 1.575 Left Center Right Operating point (mm in) 200 7.874 FX-102 FX-101 100 3.937 0 40 1.575 White non-glossy paper L Fiber head 20 0 20 40 0.787 0.787 1.575 Left Center Right Operating point (mm in) Setting distance L (mm in) White non-glossy paper L Fiber head 200 7.874 Setting distance L (mm in) FX-101 Setting distance L (mm in) Setting distance L (mm in) Reflective type 80 3.150 100 3.937 0 20 0.787 100 0 100 200 3.937 3.937 7.874 Left Center Right Operating point (mm in) FD-G6X FX-102 50 1.969 L 200 7.874 FX-101 LASER MARKERS Sensing field FD-W8 FD-WS8 FD-WT8 Reflective type Reflective type Sensing field 100 3.937 0 40 1.575 50 0 50 100 1.969 1.969 3.937 Left Center Right Operating point (mm in) FD-P81X Fiber head 200 7.874 0 200 7.874 FX-102 FX-102 SENSOR OPTIONS Fiber head Reflective type Sensing field 400 15.748 400 15.748 FX-101 400 15.748 50 0 50 100 1.969 1.969 3.937 Left Center Right Operating point (mm in) FD-G4 Reflective type Sensing field 100 3.937 PRESSURE SENSORS STATIC CONTROL DEVICES FX-102 Fiber head Fiber head FD-FM2 Reflective type Fiber head Setting distance L (mm in) Fiber head SAFETY COMPONENTS MEASUREMENT SENSORS 600 23.622 FX-101 Setting distance L (mm in) FX-101 FX-102 Setting distance L (mm in) FX-102 200 7.874 Setting distance L (mm in) Setting distance L (mm in) 300 11.811 FX-102 200 7.874 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS WIRESAVING SYSTEMS Parallel deviation 800 9.843 1,000 39.370 LASER SENSORS INDUCTIVE PROXIMITY 200 0 200 400 SENSORS 7.874 7.874 15.748 PARTICULAR Left Center Right USE Operating point (mm in) SENSORS FT-W8 FT-WS8 Thru-beam type 400 15.748 0 200 7.874 L 500 0 500 1,000 19.685 19.685 39.37 Left Center Right Operating point (mm in) Parallel deviation Fiber head Fiber head 0 400 15.748 FIBER SENSORS AREA SENSORS FX-102 500 19.685 FT-W4 FT-WS4 Thru-beam type Thru-beam type Parallel deviation Setting distance L (mm in) FX-102 Setting distance L (mm in) FX-102 3,000 118.11 Setting distance L (mm in) 4,000 157.48 4,000 157.48 Setting distance L (mm in) Contact our office for sensing characteristics that are not contained here. Thru-beam type Parallel deviation * Vertical direction 134 FX-100 SERIES Digital Fiber Sensor FX-102 60 2.362 40 1.575 FX-101 20 0.787 0 20 0.787 White non-glossy paper L Fiber head 10 0 10 20 0.394 0.394 0.787 Left Center Right Operating point (mm in) 135 Digital Fiber Sensor PRECAUTIONS FOR PROPER USE FIBER SENSORS LASER SENSORS AREA SENSORS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Using in combination with the FX-300 / FX-400 series * The FX-100 series does not use the horizontal connectors that are used with the FX-300 / FX-400 series. Please note that horizontal connection cannot be performed using a connector attached cable. In addition, the optical communication function is not equipped on the FX-100 series, so it is unable to perform interference prevention for use with the FX-300 / FX-400 series. If using the FX-100 series together with the FX-300 / FX-400 series side-by-side, please set the same models together in groups. Fibers FT / FD / FR Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-100 FX-300 FX-11A FX-301-F Other Products ON key / Setting value UP key Operation indicator (Orange) 1 Digital display (Green) (Threshold value) Setting item Factory setting Teaching mode Output operation setting 2 Description Threshold value can be set in 2-level teaching, limit teaching, or full-auto teaching. [Dark-ON] [Without timer] Light-ON or Dark-ON can be set. Without timer, ON delay timer, or OFF delay timer can be set. In case of setting ON-delay timer or OFF-delay Fit the rear part of the mounting section of the amplifier on a 35 mm 1.378 in width DIN rail. Press down the rear part of the mounting section of the unit on the 35 mm 1.378 in width DIN rail and fit the front part of the mounting section to the DIN rail. Push the amplifier forward. Lift up the front part of the amplifier to remove it. Digital display (Red) (Incident light intensity) Setting mode * Setting mode appears after the MODE key is pressed for 2 sec. in RUN mode. Timer setting [ON-delay timer: 10 ms] timer in the timer operation setting mode, timer can be set. When timer is not set, this mode is [OFF-delay timer: 10 ms] not displayed. 2 1 Emission amount setting Emission frequency setting 1 [OFF] FX-101 35 mm 1.378 in width DIN rail How to remove the amplifier 1 OFF key / Setting value DOWN key MODE key How to mount the amplifier 0 (Response time: 250 s or less) FX-102 1 (Response time: 2.5 ms or less) 2 Note: Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. FX-410 FX-311 Part description Timer operation setting Mounting 2 Selection Guide Refer to p.986~ for general precautions, and to the "Operation Guide" or "SUNX website" (http://www.sunx.com) for details pertaining to operating instructions for the amplifier. * Never use this product as a sensing device for personnel protection. * In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS SAFETY COMPONENTS FX-100 SERIES * Use M3 screws with washers for mounting. The tightening torque should be 0.5 N*m or less. M3 screw with washer Setting for reduced intensity of emission amount is possible when the incident light intensity is saturated. In case of using the fiber heads in parallel, interference can be prevented by setting different emission frequency. However, when emission frequency 0 is set, interference cannot be prevented. Response time corresponds to emission frequency. For details, refer to "SPECIFICATIONS" on p.132. Digital Fiber Sensor PRECAUTIONS FOR PROPER USE * PRO mode appears after the MODE key is pressed for 4 sec. in RUN mode. Shift setting External input setting Threshold value follow-up cycle setting (Note 1) GETA function setting (Note 2, 3) ECO setting Digital display inversion setting Threshold value margin setting Setting copy Reset Setting copy function * This can copy the settings of the master side amplifier to the slave side amplifier. Description * Be sure to use the setting copy function between the identical models (Between FX-10 models or FX-102 models). This function cannot be used between different models. * Only one sensor can be connected on slave side with a master side sensor for the setting copy function. * Threshold value, output operation setting, timer operation setting, timer setting, light-emitting amount setting, shift setting, ECO setting, digital display inversion setting, and threshold value margin setting can be copied. Shift amount can be selected from 0 to 80 % in the limit teaching. Select 0 % when it is desired [Shift amount 15 %] to set the present incident light intensity as a threshold value. [Emission halt] [OFF] [OFF] [OFF] Extemal input can be selected from emission halt, limit +, limit -, AUTO, and ECO. When incident light intensity exceeds threshold value, this mode can change the threshold value with each set cycle depending on variations of the incident light intensity. The follow-up shift amount is same as the one set in the shift setting mode. However, the threshold value is not stored. Variations can be reduced by correcting the present incident light intensity in each amplifier to a target value. Target value to offset incident light intensity can be selected from 0 to 2,000 by 100 unit each. For example, if the target value is set to 2,000 when the incident light intensity is 1,500, the incident light intensity becomes 2,000. It is possible to light up / turn off the digital display. When ECO setting mode is ON, the display turns off in 20 sec. approx. in RUN mode. To light up the display again, press any key for 2 sec. or more. 1 Set the setting copy mode of the master side amplifier to "Copy sending ON", and press the MODE key so that " " is shown on the digital display and the sensor is in copy ready state. For the setting method, refer to "Operation guide". 2 Turn off the master side amplifier. 3 Connect the master side amplifier with the slave side amplifier as shown below. Master side amplifier Digital display can be inverted. FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Color code of cable with connector (Brown) +V (Black) Input [OFF] 136 Refer to p.986~ for general precautions, and to the "Operation Guide" or "SUNX website" (http://www.sunx.com) for details pertaining to operating instructions for the amplifier. PRO mode Setting item Factory setting FX-100 SERIES (White) Extemal input + - 12 to 24V DC 10 % (Blue) 0 V [OFF] [NO] [NO] Margin for threshold value to the present incident light intensity can be checked. When there is no margin, it is possible to make the digital display blink. : Set to "OFF": does not function. : Green blinks. : Red blinks. : Red and green blink. The settings of the master side amplifier can be copied to the slave side amplifier. For details, refer to "Setting copy function." Slave side amplifier (Black) Input (White) Extemal input (Blue) 0 V 4 5 Returns to default settings (factory settings.) Notes: 1) If the incident light intensity becomes "300" or less, the follow-up operation stops. In that condition, threshold value [digital display (green)] blinks. This function can be used when thru-beam type or retroreflective type fiber is applied to this product. If reflective type fiber is applied, the function cannot be used depending on use conditions. 2) If MODE key is pressed in RUN mode when GETA function is used, the incident light intensity before setting GETA function is displayed on the red digital display for 2 sec. approx. 3) When GETA function is used in saturation of incident light intensity " is indicated on the red digital display. (4,000 or more,) " Correction value is up to 4,000. (Brown) +V 6 7 Turn on the master side amplifier and the slave side amplifier at the same time. (Note) " " is shown on the green digital display of the master side amplifier and 4-digit code is shown on the red digital display of it, then the copying starts. During copy communication, " " is shown on the green digital display of the slave side amplifier, and the ongoing copy communication indicator (" " " " " " " ") is displayed on the red digital display. When the copying is completed, " " is shown on the green digital display of the slave side amplifier, while the 4-digit code (the same code as the master side amplifier) is shown on the red digital display of it. Turn off the power of the master side amplifier and the slave side amplifier and disconnect the wire. * If copying the settings to another amplifier repeatedly, follow the steps 3 to 7 . Note: Take care that if the power is not turned on at the same time, the setting contents may not be copied. 1 2 While the slave side amplifier is disconnected, turn on the power of the master side amplifier. Press the MODE key for 2 sec. approx. Selection Guide Fibers FT / FD / FR Fiber Fiber Sensor Sensor Amplifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products 137 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS SAFETY COMPONENTS PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS MEASUREMENT SENSORS STATIC CONTROL DEVICES LASER MARKERS Selection Guide Fibers FT / FD / FR Fiber Sensor sensor Fiber Ampilifi ers Amplifiers FX-100 FX-300 FX-410 FX-311 FX-11A FX-301-F Other Products Digital Fiber Sensor FX-100 SERIES PRECAUTIONS FOR PROPER USE Refer to p.986~ for general precautions, and to the "Operation Guide" or "SUNX website" (http://www.sunx.com) for details pertaining to operating instructions for the amplifier. Quick setting function Code setting function * Settings for "output operation", "light-emitting amount", "timer", and "emission frequency" are possible simply by selecting a setting number. * The quick setting function makes it possible to set the content of the SET Mode (output operation, timer operation, amount of light emitted, and frequency of light emitted) simply by selecting a setting number. * While in the RUN Mode, pressing and holding both the ON key ( ) and OFF key ( ) simultaneously for 2 seconds will switch to the quick setting function. No. Output operation Emission amount setting Timer D-ON OFF non D-ON ON non D-ON OFF ofd 10 ms D-ON ON ofd 10 ms D-ON OFF ofd 40 ms D-ON ON ofd 40 ms D-ON OFF ond 10 ms D-ON ON ond 10 ms D-ON OFF ond 40 ms D-ON ON ond 40 ms L-ON ON ond 40 ms L-ON OFF ond 40 ms L-ON ON ond 10 ms L-ON OFF ond 10 ms L-ON ON ofd 40 ms L-ON OFF ofd 40 ms L-ON ON ofd 10 ms L-ON OFF ofd 10 ms L-ON ON non L-ON OFF non * Settings for "output operation", "timer", "emission amount", "emission frequency", "ECO", "external input", and "shift amount" are possible by selecting codes discretionary. * The code setting function makes it possible to set the output operation, timer operation, amount of light emitted, frequency of light emitted, ECO setting, external input, and amount of shift by selecting a code of one's choice. * While in the RUN Mode, pressing and holding both the ON key ( ) and OFF key ( ) simultaneously for 4 seconds will switch to the code setting function.

 1st digit 2nd digit 3rd digit 4th digit Emission Emission Code Output Timer Extemal Shift Frequency amount ECO operation (Note5) input (Note5) setting FX-101 FX-102 D-on non 0 1 E_oF ond 10 ms 1 2 Limit [+] 2 3 Limit [-] 15 % 3 4 Auto 20 % ond 40 ms OFF ofd 10 ms ofd 40 ms 0 1 Eco 25 % non 1 2 E_oF 30 % 2 3 Limit [+] 35 % 3 4 ond 10 ms L-on OFF 5% 10 % ond 40 ms ON ON Limit [-] 40 % ofd 10 ms Auto 45 % ofd 40 ms Eco 50 % Notes: 1) When the present setting is out of the code setting range, " " is shown. When " " is selected, the set content of the digit is not changed. ". 2) The factory setting is " Others * Do not use during the initial transient time (0.5 sec.) after the power supply is switched on. * EEPROM is adopted to this product. It is not possible to conduct teaching 100 thousand times or more, because of the EEPROM's lifetime. Digital Fiber Sensor FX-102 Amplifier 47 1.850 29 1.142 20 12.2 0.787 0.480 0.8 0.031 FX-101(P)-Z FX-102(P)-Z 6 0.236 6 0.236 2.7 0.106 0.7 0.028 Amplifier 0.7 0.028 MODE key Operation indicator (Orange) 4.1 0.161 Digital display (Green, Red) 2.7 0.106 OFF key / Setting value DOWN key ON key / Setting value UP key MODE key 9 0.354 9 0.354 1 0.039 7 0.276 1.1 0.043 3 0.118 10 30 0.3941.181 4 0.157 10 0.394 8.1 0.319 o3.2 o0.126 50 1.969 13.5 35 1.378 0.531 64.5 2.539 o6.5 o0.256 30 10 0.3941.181 10 0.394 4 0.157 5.5 0.217 1 0.039 1.1 0.043 7 0.276 0.8 0.031 o3.2 o0.126 3.2 2 0.126 0.079 3.2 8.1 0.126 0.319 2 0.079 3 0.118 50 1.969 5.5 0.217 13.5 0.531 Suitable for 35 mm 1.378 in width DIN rail 35 1.378 64.5 2.539 Suitable for 35 mm 1.378 in width DIN rail 0.8 0.031 o3.2 o0.126 4 0.157 5.5 0.217 13.5 0.531 50 1.969 35 1.378 64.5 2.539 PRESSURE SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRESAVING SYSTEMS 30 10 0.394 1.181 8.1 0.319 3 0.118 10 0.394 SAFETY COMPONENTS LASER MARKERS 2 0.079 2 0.079 7 6 0.236 0.276 1.1 0.043 AREA SENSORS STATIC CONTROL DEVICES 0.75 0.030 66.2 2.606 LASER SENSORS MEASUREMENT SENSORS Assembly dimensions with optional protective cover (FC-FX-1) 9 0.354 FIBER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS 6 6 10.85 0.236 0.236 0.427 47 1.850 29 1.142 12.2 0.8 0.031 0.480 OFF key / Setting value DOWN key ON key / Setting value UP key 4.1 Operation indicator (Orange) 0.161 Digital display (Green, Red) 138 Refer to p.106~ for fiber dimensions. The CAD data in the dimensions can be downloaded from the website: http://www.sunx.com DIMENSIONS (Unit: mm in) FX-101 FX-100 SERIES 3.2 0.126 2 0.079 Selection Guide Suitable for 35 mm 1.378 in width DIN rail Fibers MS-DIN-4 Amplifer mounting bracket (Optional) o7.2 mm o0.283 in spot facing, 4 0.157 deep o3.2 o0.126 9.25 0.364 o6.2 mm o0.244 in spot facing, 3 0.118 deep 3.2 0.126 5 0.197 Material: PBT CN-14A-C (0.3158 ) 35 1.378 ( ) M3 (Iength 18 mm 0.709 in) pan head screws 60 2.362 3 0.118 6.2 mm 0.244 in spot facing, 3 0.118 deep M3 Square nut 5.6 0.220 24.7 0.972 9 0.354 3.2 0.126 o3.2 o0.126 1 0.039 24.5 0.965 35 1.378 32 1.260 4 0.157 Suitable for 35 mm 1.378 in width DIN rail Material: Polycarbonate CN-14A-R-C Connector attached cable (Optional) CN-14A-C2 is attached FX-101(P)-CC2 / FX-102(P)-CC2 * Length L 50 1.969 ( ) (0.3158 ) o3.7 o0.146 cable FX-300 FX-410 FX-311 FX-11A FX-301-F 1.6 0.063 L FT / FD / FR Fiber Fiber Sensor Sensor Amplifi ers Amplifiers FX-100 2.75 0.108 3 0.118 15 0.591 11.5 0.453 4 0.157 End plate (Optional) 7.2 mm 0.283 in spot facing, 4 0.157 deep 1 0.039 15 0.591 MS-DIN-E Model No. CN-14A(-R)-C1 CN-14A(-R)-C2 CN-14A(-R)-C3 CN-14A(-R)-C5 Length L 1,000 39.370 2,000 78.740 3,000 118.110 5,000 196.850 Other Products