0805 POWER INDUCTORS Power Inductor for Critical Applications ST336PHA Shielded power inductors Excellent current handling for a part this size; low DCR Core material Ceramic/Ferrite Terminations Silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 57.6 - 62.4 mg Ambient temperature -40C to +65C with Irms current, +65C to +105C with derated current Storage temperature Component: -55C to +105C. Packaging: -55C to +80C Resistance to soldering heat Max three 40 second reflows at +260C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30C / 85% relative humidity) Packaging 1500/7 reel; 7500/13 reel Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 2.34 mm pocket depth Part number1 ST336PHA102KLZ ST336PHA152KLZ ST336PHA272KLZ ST336PHA332KLZ ST336PHA392KLZ ST336PHA472KLZ ST336PHA562KLZ ST336PHA682KLZ ST336PHA103KLZ ST336PHA153KLZ ST336PHA223KLZ ST336PHA333KLZ ST336PHA473KLZ ST336PHA683KLZ ST336PHA823KLZ ST336PHA104KLZ ST336PHA124KLZ ST336PHA154KLZ ST336PHA224KLZ ST336PHA334KLZ L2DCR4SRF5 10%Q min3 max typ (H) at 1 MHz (Ohms) (MHz) 1.0 21 0.14 340 1.5 21 0.18 265 2.7 21 0.35 190 3.3 21 0.50 180 3.9 21 0.74 165 4.7 21 0.85 155 5.6 21 0.91 143 6.8 21 1.37 118 10 21 1.51 66 15 21 2.04 34 22 25 2.48 22 33 25 3.00 17 47 25 3.85 15 68 28 4.42 12 82 30 6.00 12 100 32 6.96 9.0 120 32 7.51 7.7 150 32 8.33 5.0 220 32 13.71 5.0 330 32 20.53 3.5 Isat6Irms7 (A) (A) 0.90 1.6 0.85 1.3 0.60 0.88 0.55 0.70 0.50 0.61 0.43 0.59 0.38 0.57 0.32 0.46 0.27 0.43 0.22 0.34 0.18 0.33 0.16 0.28 0.15 0.26 0.12 0.24 0.11 0.21 0.10 0.19 0.10 0.18 0.08 0.18 0.07 0.14 0.06 0.11 1. When ordering, please specify testing code: ST336PHA334KLZ Testing: Z = COTS H = Group A screening per Coilcraft CP-SA-10001 2. Inductance measured at 100 kHz, 0.1 Vrms, using a Coilcraft SMDA fixture in Agilent/HP 4263B LCR meter. 3. Q measured on an Agilent/HP 4291 with an Agilent/HP 16193 test fixture. 4. DCR measured on a micro-ohmmeter and a Coilcraft CCF840 test fixture. 5. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. 6. DC current at which the inductance drops 10% (typ) from its value without current. 7. Current that causes a 40C temperature rise from 25C ambient. 8. Electrical specifications at 25C. Refer to Doc 362 "Soldering Surface Mount Components" before soldering. Document ST265-1 Revised 06/12/13 (R) (c) Coilcraft, Inc. 2013 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email cps@coilcraft.com www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information. 0805 POWER INDUCTORS Power Inductor for Critical Applications - ST336PHA Typical L vs Frequency Typical L vs Current 1000 1000 330 H 330 H 100 H 10 H 10 3.3 H 1 H 1 0.1 0.01 100 H 100 Inductance (H) Inductance (H) 100 10 H 10 3.3 H 1 H 1 1 0.1 0.1 10 1 100 10 1000 Current (mA) Frequency (MHz) Irms Derating Typical Q vs Frequency 120 70 110 60 330 H 40 100 H 1 H 30 3.3 H 20 10 H 80 70 60 50 40 30 20 10 0 90 25C Q factor 50 Percent of rated Irms 100 10 1 0.1 10 -40 -20 0 20 40 60 80 100 120 Ambient temperature (C) Frequency (MHz) C D B F 0 H I E A J I G Terminal wraparound: approx 0.010/0,25 both ends Recommended Suggested Land Land Pattern Pattern A B C max max max D E F G H I J 0.133 0.118 0.079 0.053 0.080 0.050 0.020 0.070 0.040 0.030 inches 3,38 3,00 2,00 1,35 2,03 1,27 0,51 1,78 1,02 0,76 mm Note: Height dimension is before optional solder application. For maximum height including solder, add 0.006 in / 0,15 mm. Document ST265-2 Revised 06/12/13 (R) (c) Coilcraft, Inc. 2013 1102 Silver Lake Road Cary, IL 60013 Phone 800-981-0363 Fax 847-639-1508 Email cps@coilcraft.com www.coilcraft-cps.com This product may not be used in medical or high risk applications without prior Coilcraft approval. Specifications subject to change without notice. Please check our web site for latest information.