I N D U C T O R S October 2013 Inductors for High Frequency Circuits Multilayer Ceramic MLG-Pseries MLG0603P 0603 [0201 inch]* * Dimensions Code JIS[EIA] (For automobiles) (2/12) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (3/12) I N D U C T O R S Inductors for High Frequency Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 Multilayer Ceramic Overview of the MLG-P Series FEATURES High Q type inductor for high-frequency circuits. The 0402 Series has0.2 to 33nH, and the 0603 Series has 0.6 to 120nH. 0.1n step inductance lineup. Compared with existing products, the size was greatly reduced, making it optimal for fine-pitch circuits. Optimal configuration that greatly improves the Q to 800MHz or higher. Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for Highfrequency. APPLICATION Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners and other high frequency circuits for the mobile communication industry PART NUMBER CONSTRUCTION MLG Series name 0603 LxWxH Dimensions (mm) 0603 0.6x0.3x0.3 P Characteristics P 1N1 B Inductance (H) 1N1 1.1 11N 11 Inductance tolerance B 0.1nH C 0.2nH S 0.3nH H 3% J 5% T Packaging style Internal code T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) C C MLG0603P -55 to +125 -55 to +125 15000 The Storage temperature range is for after the circuit board is mounted. Individual weight mg 0.2 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (4/12) I N D U C T O R S Overview of the MLG-P Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s max. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (5/12) I N D U C T O R S MLG-Pseries MLG0603P Type 0.300.03 SHAPE & DIMENSIONS 0.090.04 0.090.04 0.300.03 0.600.03 0.150.05 0.150.05 Dimensions in mm 0.3 RECOMMENDED LAND PATTERN 0.25 0.3 0.25 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (6/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 Q min. Tolerance 0.1, 0.2nH 0.1, 0.2nH 0.1, 0.2nH 0.1, 0.2nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 0.1, 0.2, 0.3nH 3%, 5%, 0.3nH 3%, 5%, 0.3nH 3%, 5%, 0.3nH 3%, 5%, 0.3nH 3%, 5%, 0.3nH 3%, 5% 3%, 5% 3%, 5% 3%, 5% -- -- -- -- 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 L, Q measuring frequency (MHz) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 Self-resonant frequency (GHz) min. typ. 10.0 20.0 10.0 20.0 10.0 20.0 10.0 20.0 10.0 20.0 10.0 19.9 10.0 16.0 10.0 13.9 10.0 11.7 10.0 14.9 10.0 13.4 10.0 12.8 9.0 10.7 9.0 10.9 8.5 10.1 8.0 9.8 7.5 9.0 7.5 8.4 7.5 10.9 7.5 9.9 7.5 10.1 7.5 10.0 7.5 9.9 7.5 9.2 7.5 9.1 7.5 8.8 7.5 8.4 7.5 8.4 7.0 8.1 6.5 8.0 6.5 7.7 6.5 7.4 5.8 7.0 5.8 7.1 5.8 6.7 5.8 6.7 5.8 6.6 5.8 6.7 5.5 6.9 5.5 6.6 4.0 5.3 4.0 6.3 4.0 6.1 4.0 5.4 4.0 5.2 4.0 5.0 DC resistance (: ) max. 0.06 0.06 0.06 0.06 0.07 0.07 0.08 0.08 0.09 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.30 0.30 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.70 0.75 0.80 0.85 0.90 typ. 0.01 0.01 0.02 0.02 0.02 0.03 0.04 0.03 0.04 0.03 0.03 0.02 0.03 0.04 0.03 0.05 0.07 0.07 0.12 0.09 0.14 0.14 0.10 0.10 0.14 0.10 0.14 0.13 0.13 0.12 0.10 0.14 0.24 0.22 0.21 0.29 0.24 0.24 0.16 0.30 0.32 0.59 0.62 0.70 0.71 0.76 Rated current (mA) max. Part No. 1000 1000 1000 1000 1000 1000 800 800 800 800 700 700 700 600 600 600 600 600 500 500 500 500 500 500 450 450 450 450 450 450 400 400 400 400 350 350 350 350 350 350 350 300 300 300 250 250 MLG0603P0N6T MLG0603P0N7T MLG0603P0N8T MLG0603P0N9T MLG0603P1N0T MLG0603P1N1T MLG0603P1N2T MLG0603P1N3T MLG0603P1N4T MLG0603P1N5T MLG0603P1N6T MLG0603P1N7T MLG0603P1N8T MLG0603P1N9T MLG0603P2N0T MLG0603P2N1T MLG0603P2N2T MLG0603P2N3T MLG0603P2N4T MLG0603P2N5T MLG0603P2N6T MLG0603P2N7T MLG0603P2N8T MLG0603P2N9T MLG0603P3N0T MLG0603P3N1T MLG0603P3N2T MLG0603P3N3T MLG0603P3N4T MLG0603P3N5T MLG0603P3N6T MLG0603P3N7T MLG0603P3N8T MLG0603P3N9T MLG0603P4N0T MLG0603P4N1T MLG0603P4N2T MLG0603P4N3T MLG0603P4N7T MLG0603P5N1T MLG0603P5N6T MLG0603P6N2T MLG0603P6N8T MLG0603P7N5T MLG0603P8N2T MLG0603P9N1T The " " of the Part Number contains the inductance tolerance code, B(0.1nH), C(0.2nH), S(0.3nH), H(3%) or J(5%). Please contact us for information on inductance tolerance, G (2%). * The " " of the Part Number contains the internal code. Short bar residual inductance =0.43nH Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (7/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 110 120 Q min. tolerance 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 3%, 5% 14 14 14 14 14 14 14 14 14 14 14 10 10 10 10 10 10 10 10 10 9 9 9 9 9 9 9 L, Q measuring frequency (MHz) 500 500 500 500 500 500 500 500 500 500 500 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 Self-resonant frequency (GHz) min. typ. 4.0 4.7 3.5 4.5 3.5 4.3 3.2 4.2 3.2 3.7 3.0 3.6 3.0 3.5 2.2 3.3 2.2 2.9 2.2 2.9 2.2 2.7 1.8 2.3 1.8 2.4 1.8 2.2 1.8 2.2 1.6 2.0 1.6 2.0 1.4 1.9 1.4 1.8 1.2 1.6 1.2 1.6 1.0 1.5 1.0 1.5 0.9 1.3 0.9 1.3 0.8 1.1 0.8 1.0 DC resistance (: ) max. 0.95 1.00 1.10 1.10 1.20 1.20 1.40 1.90 1.90 2.10 2.10 2.20 2.20 2.40 2.40 2.90 2.90 3.50 3.50 3.50 3.50 4.00 4.00 4.50 4.50 5.00 5.00 typ. 0.85 0.64 0.82 0.87 0.94 1.00 1.04 1.33 1.31 1.17 1.45 1.37 1.55 1.49 1.72 1.61 2.18 1.87 2.35 2.12 2.69 2.59 2.71 2.92 3.20 3.50 3.79 Rated current (mA) max. Part No. 250 250 250 250 250 200 200 150 150 140 140 130 130 120 120 110 110 100 100 100 100 80 80 80 80 80 80 MLG0603P10NT MLG0603P11NT MLG0603P12NT MLG0603P13NT MLG0603P15NT MLG0603P16NT MLG0603P18NT MLG0603P20NT MLG0603P22NT MLG0603P24NT MLG0603P27NT MLG0603P30NT MLG0603P33NT MLG0603P36NT MLG0603P39NT MLG0603P43NT MLG0603P47NT MLG0603P51NT MLG0603P56NT MLG0603P62NT MLG0603P68NT MLG0603P75NT MLG0603P82NT MLG0603P91NT MLG0603PR10T MLG0603PR11T MLG0603PR12T The " " of the Part Number contains the inductance tolerance code, B(0.1nH), C(0.2nH), S(0.3nH), H(3%) or J(5%). Please contact us for information on inductance tolerance, G (2%). * The " " of the Part Number contains the internal code. Short bar residual inductance =0.43nH Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (8/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 800MHz 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.2 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 1.8GHz 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.4 3.5 3.6 3.7 3.8 3.9 4.0 4.1 4.3 4.4 4.5 4.9 5.3 6.1 6.5 7.3 8.1 9.0 10.0 2.0GHz 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.4 2.4 2.5 2.6 2.7 2.8 2.9 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.9 4.0 4.1 4.2 4.3 4.5 4.5 5.0 5.4 6.2 6.7 7.5 8.3 9.3 10.3 2.4GHz 0.6 0.7 0.4 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.3 2.4 2.4 2.5 2.6 2.7 2.9 3.0 3.1 3.2 3.3 3.4 3.6 3.7 3.8 4.0 4.1 4.2 4.4 4.5 4.6 4.7 5.1 5.7 6.6 7.0 8.0 8.8 10.0 11.1 Q typ. 500MHz 16min. 16min. 16 17 16 17 18 17 18 17 17 17 17 18 19 18 18 18 16 17 17 17 17 17 17 17 17 18 18 18 18 18 17 17 18 18 18 17 16 16 18 16 16 16 17 17 800MHz 22min. 22min. 22 22 21 23 24 22 23 22 22 22 22 24 23 23 23 22 21 22 22 21 22 22 21 22 22 22 23 23 22 23 22 22 22 22 22 21 21 21 22 21 21 21 21 21 1.8GHz 35min. 35min. 35 35 33 36 38 34 36 33 33 33 34 36 35 34 35 33 31 33 33 33 34 34 32 33 34 33 34 34 33 34 32 32 32 33 32 32 31 31 31 30 29 30 30 30 2.0GHz 37min. 37min. 37 37 36 38 40 36 39 35 35 35 35 38 37 36 36 35 33 34 35 35 36 35 34 34 35 35 35 35 34 35 33 34 33 34 33 33 32 32 32 31 30 30 30 31 2.4GHz 41min. 41min. 41 41 40 43 45 40 43 39 38 39 39 42 41 39 40 38 36 38 38 38 40 39 37 37 38 38 38 38 37 37 36 36 36 36 35 35 34 34 32 33 31 32 31 32 Part No. MLG0603P0N6T MLG0603P0N7T MLG0603P0N8T MLG0603P0N9T MLG0603P1N0T MLG0603P1N1T MLG0603P1N2T MLG0603P1N3T MLG0603P1N4T MLG0603P1N5T MLG0603P1N6T MLG0603P1N7T MLG0603P1N8T MLG0603P1N9T MLG0603P2N0T MLG0603P2N1T MLG0603P2N2T MLG0603P2N3T MLG0603P2N4T MLG0603P2N5T MLG0603P2N6T MLG0603P2N7T MLG0603P2N8T MLG0603P2N9T MLG0603P3N0T MLG0603P3N1T MLG0603P3N2T MLG0603P3N3T MLG0603P3N4T MLG0603P3N5T MLG0603P3N6T MLG0603P3N7T MLG0603P3N8T MLG0603P3N9T MLG0603P4N0T MLG0603P4N1T MLG0603P4N2T MLG0603P4N3T MLG0603P4N7T MLG0603P5N1T MLG0603P5N6T MLG0603P6N2T MLG0603P6N8T MLG0603P7N5T MLG0603P8N2T MLG0603P9N1T The " " of the Part Number contains the inductance tolerance code, B(0.1nH), C(0.2nH), S(0.3nH), H(3%) or J(5%). Please contact us for information on inductance tolerance, G (2%). * The " " of the Part Number contains the internal code. Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (9/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 10 11 12 13 15 16 18 20 22 24 27 30 33 37 40 44 48 53 58 65 71 79 87 99 110 126 151 800MHz 10 11 12 13 15 16 18 21 23 25 28 32 36 39 43 48 53 59 66 76 82 97 109 132 152 211 1.8GHz 11 13 14 15 18 20 23 27 34 36 45 59 68 2.0GHz 12 13 15 16 20 22 26 31 40 43 57 2.4GHz 13 15 17 19 24 27 33 42 68 72 Q typ. 500MHz 16 18 18 18 18 18 18 18 18 19 18 18 15 16 15 15 15 15 15 15 15 14 14 13 14 13 12 800MHz 21 23 22 22 22 22 22 22 21 22 21 21 17 17 17 16 16 16 15 15 15 13 13 12 12 9 1.8GHz 28 30 28 28 27 26 25 23 21 21 18 15 11 2.0GHz 28 30 28 28 26 25 24 22 18 18 15 2.4GHz 28 30 27 26 24 22 20 17 11 11 Part No. MLG0603P10NT MLG0603P11NT MLG0603P12NT MLG0603P13NT MLG0603P15NT MLG0603P16NT MLG0603P18NT MLG0603P20NT MLG0603P22NT MLG0603P24NT MLG0603P27NT MLG0603P30NT MLG0603P33NT MLG0603P36NT MLG0603P39NT MLG0603P43NT MLG0603P47NT MLG0603P51NT MLG0603P56NT MLG0603P62NT MLG0603P68NT MLG0603P75NT MLG0603P82NT MLG0603P91NT MLG0603PR10T MLG0603PR11T MLG0603PR12T The " " of the Part Number contains the inductance tolerance code, B(0.1nH), C(0.2nH), S(0.3nH), H(3%) or J(5%). Please contact us for information on inductance tolerance, G (2%). * The " " of the Part Number contains the internal code. Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (10/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 1000 R10 R12 82N 68N 56N 47N39N 33N 27N 22N 100 18N 15N Inductance(nH) 12N 10N 8N2 10 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1 1N0 0 10 100 1000 10000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (11/12) I N D U C T O R S MLG-Pseries MLG0603P Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 50 1N2 1N0 1N5 1N8 2N7 3N3 40 2N2 3N9 4N7 5N6 30 6N8 Q 8N2 10N 12N 20 15N 18N 10 56N 82N 47N 39N 68N 33N 22N R12 0 10 R10 27N 100 1000 10000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies Equivalent measurement equipment may be used. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm (12/12) I N D U C T O R S MLG-Pseries Packaging Style REEL DIMENSIONS o60min. 1.0 2.00.5 8.4 +2.0 -0.0 o130.2 14.4max. o210.8 o1802.0 Dimensions in mm 3.50.05 Cavity Type MLG0603P A 0.680.05 B 0.380.05 K 0.5 max. A 8.00.3 Sprocket hole 1.5 +0.1 -0.0 1.750.1 TAPE DIMENSIONS K B 4.00.1 2.00.05 160min. Taping 2.00.05 200min. Drawing direction 300min. * All specifications are subject to change without notice. 001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm