SN74LS373, SN74LS374 Octal Transparent Latch with 3-State Outputs; Octal D-Type Flip-Flop with 3-State Output http://onsemi.com The SN74LS373 consists of eight latches with 3-state outputs for bus organized system applications. The flip-flops appear transparent to the data (data changes asynchronously) when Latch Enable (LE) is HIGH. When LE is LOW, the data that meets the setup times is latched. Data appears on the bus when the Output Enable (OE) is LOW. When OE is HIGH the bus output is in the high impedance state. The SN74LS374 is a high-speed, low-power Octal D-type Flip-Flop featuring separate D-type inputs for each flip-flop and 3-state outputs for bus oriented applications. A buffered Clock (CP) and Output Enable (OE) is common to all flip-flops. The SN74LS374 is manufactured using advanced Low Power Schottky technology and is compatible with all ON Semiconductor TTL families. * * * * * * * Eight Latches in a Single Package 3-State Outputs for Bus Interfacing Hysteresis on Latch Enable Edge-Triggered D-Type Inputs Buffered Positive Edge-Triggered Clock Hysteresis on Clock Input to Improve Noise Margin Input Clamp Diodes Limit High Speed Termination Effects LOW POWER SCHOTTKY MARKING DIAGRAMS SN74LS37xN AWLYYWW 1 20 1 PDIP-20 N SUFFIX CASE 738 LS37x AWLYYWW 20 GUARANTEED OPERATING RANGES Symbol VCC Parameter Supply Voltage 1 Min Typ Max 1 Unit 4.75 5.0 5.25 V 0 25 70 C TA Operating Ambient Temperature Range IOH Output Current - High -2.6 mA IOL Output Current - Low 24 mA SOIC-20 DW SUFFIX CASE 751D 74LS37x AWLYWW 20 1 SOEIAJ-20 M SUFFIX CASE 967 x A WL YY WW 1 = 3 or 4 = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. Semiconductor Components Industries, LLC, 2001 October, 2001 - Rev. 8 1 Publication Order Number: SN74LS373/D SN74LS373, SN74LS374 CONNECTION DIAGRAM DIP (TOP VIEW) SN74LS374 SN74LS373 VCC O7 D7 D6 O6 O5 D5 D4 O4 LE 20 19 18 17 16 15 14 13 12 11 1 OE 2 O0 3 D0 4 D1 5 O1 6 O2 7 D2 8 D3 9 O3 10 GND VCC O7 NOTE: The Flatpak version has the same pinouts (Connection Diagram) as the Dual InLine Package. D7 D6 O6 O5 D5 D4 O4 CP 20 19 18 17 16 15 14 13 12 11 1 OE 2 O0 3 D0 4 D1 5 O1 6 O2 7 D2 8 D3 9 O3 10 GND LOADING (Note a) PIN NAMES D0 - D7 LE CP OE O0 - O7 Data Inputs Latch Enable (Active HIGH) Input Clock (Active HIGH Going Edge) Input Output Enable (Active LOW) Input Outputs HIGH LOW 0.5 U.L. 0.5 U.L. 0.5 U.L. 0.5 U.L. 65 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 0.25 U.L. 15 U.L. NOTES: a) 1 TTL Unit Load (U.L.) = 40 A HIGH/1.6 mA LOW. TRUTH TABLE LS373 LS374 Dn LE OE On Dn H H L H H L H L L L X L L Q0 X X X H Z* H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial Z = High Impedance * Note: Contents of flip-flops unaffected by the state of the Output Enable input (OE). http://onsemi.com 2 LE X OE On L H L L H Z* SN74LS373, SN74LS374 LOGIC DIAGRAMS SN74LS373 3 4 D0 D LATCH ENABLE 11 7 D1 D2 D Q G 8 D3 D Q G 13 D Q G 14 D4 D Q G 17 D5 D6 D Q G 18 D Q G VCC = PIN 20 GND = PIN 10 D7 D Q G = PIN NUMBERS Q G LE OE 1 O0 2 O1 O2 O3 6 5 9 O4 O5 O6 15 12 16 O7 19 SN74LS374 3 4 D0 11 7 D1 8 D2 13 D3 14 D4 17 18 D5 D6 D7 CP CP D Q Q CP D Q Q CP D Q Q CP D Q Q CP D Q Q CP D Q Q CP D Q Q CP D Q Q OE 1 O0 2 O1 5 O2 O3 6 O4 9 O5 12 15 O6 O7 16 19 DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified) Limits Symbol Parameter VIH Input HIGH Voltage VIL Input LOW Voltage VIK Input Clamp Diode Voltage VOH Output HIGH Voltage VOL Output LOW Voltage IOZH IOZL Min Typ Max 2.0 0.8 -0.65 2.4 -1.5 3.1 Unit Test Conditions V Guaranteed Input HIGH Voltage for All Inputs V Guaranteed Input LOW Voltage for All Inputs V VCC = MIN, IIN = -18 mA V VCC = MIN, IOH = MAX, VIN = VIH or VIL per Truth Table VCC = VCC MIN, VIN = VIL or VIH per Truth Table 0.25 0.4 V IOL = 12 mA 0.35 0.5 V IOL = 24 mA Output Off Current HIGH 20 A VCC = MAX, VOUT = 2.7 V Output Off Current LOW -20 A VCC = MAX, VOUT = 0.4 V 20 A VCC = MAX, VIN = 2.7 V 0.1 mA VCC = MAX, VIN = 7.0 V -0.4 mA VCC = MAX, VIN = 0.4 V -130 mA VCC = MAX ICC Power Supply Current 40 mA 1. Not more than one output should be shorted at a time, nor for more than 1 second. VCC = MAX IIH Input HIGH Current IIL Input LOW Current IOS Short Circuit Current (Note 1) -30 http://onsemi.com 3 SN74LS373, SN74LS374 AC CHARACTERISTICS (TA = 25C, VCC = 5.0 V) Limits LS373 Symbol Min Parameter Typ LS374 Max Min Typ 35 50 Max Unit fMAX Maximum Clock Frequency tPLH tPHL Propagation Delay, Data to Output 12 12 18 18 tPLH tPHL Clock or Enable to Output 20 18 30 30 15 19 28 28 ns tPZH tPZL Output Enable Time 15 25 28 36 20 21 28 28 ns tPHZ tPLZ Output Disable Time 12 15 20 25 12 15 20 25 ns Test Conditions MHz ns CL = 45 pF pF, RL = 667 CL = 5.0 pF AC SETUP REQUIREMENTS (TA = 25C, VCC = 5.0 V) Limits LS373 Symbol Min Parameter LS374 Max Min Max Unit tW Clock Pulse Width 15 15 ns ts Setup Time 5.0 20 ns th Hold Time 20 0 ns DEFINITION OF TERMS HOLD TIME (th) -- is defined as the minimum time following the LE transition from HIGH-to-LOW that the logic level must be maintained at the input in order to ensure continued recognition. SETUP TIME (ts) -- is defined as the minimum time required for the correct logic level to be present at the logic input prior to LE transition from HIGH-to-LOW in order to be recognized and transferred to the outputs. SN74LS373 AC WAVEFORMS tW tW 1.3 V LE ts th Dn tPLH tPHL OUTPUT Figure 1. OE 1.3 V tPZL VOUT OE 1.3 V tPLZ 1.3 V 1.3 V Figure 2. 0.5 V 1.3 V tPZH VOUT VOL 1.3 V tPHZ 1.3 V 0.5 V Figure 3. http://onsemi.com 4 VOH 1.3 V SN74LS373, SN74LS374 SN74LS373 AC LOAD CIRCUIT VCC SWITCH POSITIONS RL SYMBOL SW1 TO OUTPUT UNDER TEST SW1 SW2 tPZH Open Closed tPZL Closed Open tPLZ Closed Closed tPHZ Closed Closed 5.0 k CL* SW2 * Includes Jig and Probe Capacitance. Figure 4. SN74LS374 AC WAVEFORMS tWH tWL 1.3 V 1.3 V CP OE 1.3 V th ts VOUT 1.3 V Dn OUTPUT tPLZ 1.3 V 1.3 V tPZH Figure 6. 1.3 V 1.3 V tPHZ 1.3 V 1.3 V 1.3 V 0.5 V Figure 5. VOUT 1.3 V tPHL tPLH OE 1.3 V tPZL VOH 1.3 V 0.5 V Figure 7. http://onsemi.com 5 VOL SN74LS373, SN74LS374 SN74LS374 AC LOAD CIRCUIT VCC SWITCH POSITIONS RL SW1 TO OUTPUT UNDER TEST SYMBOL SW1 SW2 tPZH Open Closed tPZL Closed Open tPLZ Closed Closed tPHZ Closed Closed 5.0 k CL* SW2 * Includes Jig and Probe Capacitance. Figure 8. DEVICE ORDERING INFORMATION Device Order Number Package Type Tape and Reel Size PDIP-20 1440 Units/Box SN74LS373DW SOIC-WIDE 38 Units/Rail SN74LS373DWR2 SOIC-WIDE 2500/Tape and Reel SN74LS373M SOEIAJ-20 See Note 2 SN74LS373MEL SOEIAJ-20 See Note 2 PDIP-20 1440 Units/Box SN74LS374DW SOIC-WIDE 38 Units/Rail SN74LS374DWR2 SOIC-WIDE 2500/Tape and Reel SN74LS374M SOEIAJ-20 See Note 2 SN74LS374MEL SOEIAJ-20 See Note 2 SN74LS373N SN74LS374N 2. For ordering information on the EIAJ version of the SOIC package, please contact your local ON Semiconductor representative. http://onsemi.com 6 SN74LS373, SN74LS374 PACKAGE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 738-03 ISSUE E -A- 20 11 1 10 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. B L C -T- DIM A B C D E F G J K L M N K SEATING PLANE M N E G F J D 20 PL 0.25 (0.010) 20 PL 0.25 (0.010) T A M M T B M M INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 0 15 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0 15 0.51 1.01 D SUFFIX PLASTIC SOIC PACKAGE CASE 751D-05 ISSUE F A 20 X 45 h 1 10 20X B B 0.25 M T A S B S A L H M E 0.25 10X NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF B DIMENSION AT MAXIMUM MATERIAL CONDITION. 11 B M D 18X e A1 SEATING PLANE C T http://onsemi.com 7 DIM A A1 B C D E e H h L MILLIMETERS MIN MAX 2.35 2.65 0.10 0.25 0.35 0.49 0.23 0.32 12.65 12.95 7.40 7.60 1.27 BSC 10.05 10.55 0.25 0.75 0.50 0.90 0 7 SN74LS373, SN74LS374 PACKAGE DIMENSIONS M SUFFIX SOEIAJ PACKAGE CASE 967-01 ISSUE O 20 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 11 Q1 M E HE 1 L 10 DETAIL P Z D VIEW P e A c A1 b 0.13 (0.005) M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 12.35 12.80 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 --0.81 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.486 0.504 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 --0.032 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800-282-9855 Toll Free USA/Canada http://onsemi.com 8 SN74LS373/D