To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. User's Manual PD780024A, 780034A, 780024AY, 780034AY Subseries 8-Bit Single-Chip Microcontrollers PD780021A PD780022A PD780023A PD780024A PD780021A(A) PD780022A(A) PD780023A(A) PD780024A(A) PD780031A PD780032A PD780033A PD780034A PD780031A(A) PD780032A(A) PD780033A(A) PD780034A(A) PD78F0034A PD78F0034B PD78F0034B(A) Document No. U14046EJ5V0UD00 (5th edition) Date Published March 2005 N CP(K) (c) Printed in Japan 1999, 2003 PD780021AY PD780022AY PD780023AY PD780024AY PD780021AY(A) PD780022AY(A) PD780023AY(A) PD780024AY(A) PD780031AY PD780032AY PD780033AY PD780034AY PD780031AY(A) PD780032AY(A) PD780033AY(A) PD780034AY(A) PD78F0034AY PD78F0034BY PD78F0034BY(A) [MEMO] 2 User's Manual U14046EJ5V0UD NOTES FOR CMOS DEVICES 1 VOLTAGE APPLICATION WAVEFORM AT INPUT PIN Waveform distortion due to input noise or a reflected wave may cause malfunction. If the input of the CMOS device stays in the area between VIL (MAX) and VIH (MIN) due to noise, etc., the device may malfunction. Take care to prevent chattering noise from entering the device when the input level is fixed, and also in the transition period when the input level passes through the area between VIL (MAX) and VIH (MIN). 2 HANDLING OF UNUSED INPUT PINS Unconnected CMOS device inputs can be cause of malfunction. If an input pin is unconnected, it is possible that an internal input level may be generated due to noise, etc., causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND via a resistor if there is a possibility that it will be an output pin. All handling related to unused pins must be judged separately for each device and according to related specifications governing the device. 3 PRECAUTION AGAINST ESD A strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it when it has occurred. Environmental control must be adequate. When it is dry, a humidifier should be used. It is recommended to avoid using insulators that easily build up static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work benches and floors should be grounded. The operator should be grounded using a wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with mounted semiconductor devices. 4 STATUS BEFORE INITIALIZATION Power-on does not necessarily define the initial status of a MOS device. Immediately after the power source is turned ON, devices with reset functions have not yet been initialized. Hence, power-on does not guarantee output pin levels, I/O settings or contents of registers. A device is not initialized until the reset signal is received. A reset operation must be executed immediately after power-on for devices with reset functions. 5 POWER ON/OFF SEQUENCE In the case of a device that uses different power supplies for the internal operation and external interface, as a rule, switch on the external power supply after switching on the internal power supply. When switching the power supply off, as a rule, switch off the external power supply and then the internal power supply. Use of the reverse power on/off sequences may result in the application of an overvoltage to the internal elements of the device, causing malfunction and degradation of internal elements due to the passage of an abnormal current. The correct power on/off sequence must be judged separately for each device and according to related specifications governing the device. 6 INPUT OF SIGNAL DURING POWER OFF STATE Do not input signals or an I/O pull-up power supply while the device is not powered. The current injection that results from input of such a signal or I/O pull-up power supply may cause malfunction and the abnormal current that passes in the device at this time may cause degradation of internal elements. Input of signals during the power off state must be judged separately for each device and according to related specifications governing the device. User's Manual U14046EJ5V0UD 3 EEPROM, FIP, and IEBus are trademarks of NEC Electronics Corporation. Windows and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. HP9000 Series 700 and HP-UX are trademarks of Hewlett-Packard Company. SPARCstation is a trademark of SPARC International, Inc. Solaris and SunOS are trademarks of Sun Microsystems, Inc. TRON is an abbreviation of The Realtime Operating system Nucleus. ITRON is an abbreviation of Industrial TRON. 4 User's Manual U14046EJ5V0UD These commodities, technology or software, must be exported in accordance with the export administration regulations of the exporting country. Diversion contrary to the law of that country is prohibited. * The information in this document is current as of February, 2005. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 User's Manual U14046EJ5V0UD 5 Regional Information Some information contained in this document may vary from country to country. Before using any NEC Electronics product in your application, pIease contact the NEC Electronics office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. [GLOBAL SUPPORT] http://www.necel.com/en/support/support.html NEC Electronics America, Inc. (U.S.) NEC Electronics (Europe) GmbH NEC Electronics Hong Kong Ltd. Santa Clara, California Tel: 408-588-6000 800-366-9782 Duesseldorf, Germany Tel: 0211-65030 Hong Kong Tel: 2886-9318 * Sucursal en Espana Madrid, Spain Tel: 091-504 27 87 * Succursale Francaise Velizy-Villacoublay, France Tel: 01-30-67 58 00 * Filiale Italiana Milano, Italy Tel: 02-66 75 41 * Branch The Netherlands Eindhoven, The Netherlands Tel: 040-244 58 45 * Tyskland Filial NEC Electronics Hong Kong Ltd. Seoul Branch Seoul, Korea Tel: 02-558-3737 NEC Electronics Shanghai Ltd. Shanghai, P.R. China Tel: 021-5888-5400 NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 6253-8311 Taeby, Sweden Tel: 08-63 80 820 * United Kingdom Branch Milton Keynes, UK Tel: 01908-691-133 J04.1 6 User's Manual U14046EJ5V0UD INTRODUCTION Readers This manual has been prepared for user engineers who understand the functions of the PD780024A, 780034A, 780024AY, and 780034AY Subseries and wish to design and develop application systems and programs for these devices. * PD780024A Subseries PD780021A, 780022A, 780023A, 780024A PD780021A(A), 780022A(A), 780023A(A), 780024A(A) * PD780034A Subseries PD780031A, 780032A, 780033A, 780034A, 78F0034A, 78F0034B PD780031A(A), 780032A(A), 780033A(A), 780034A(A), 78F0034B(A) * PD780024AY Subseries PD780021AY, 780022AY, 780023AY, 780024AY PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A) * PD780034AY Subseries PD780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY PD780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A), 78F0034BY(A) Purpose This manual is intended to provide users an understanding of the functions described in the organization below. Organization The PD780024A, 780034A, 780024AY, and 780034AY Subseries manual is separated into two parts: this manual and the instructions edition (common to the 78K/0 Series). PD780024A, 780034A, 780024AY, 780034AY 78K/0 Series Subseries User's Manual User's Manual (This Manual) Instructions * Pin functions * CPU functions * Internal block functions * Instruction set * Interrupt * Explanation of each instruction * Other on-chip peripheral functions * Electrical specifications User's Manual U14046EJ5V0UD 7 How To Read This Manual It is assumed that the reader of this manual has general knowledge in the fields of electrical engineering, logic circuits, and microcontrollers. * For readers who use this as an (A) product: Standard products differ from (A) products in their quality grade only. Re-read the product name as indicated below if your product is an (A) product. PD780021A PD780021A(A) PD780021AY PD780021AY(A) PD780022A PD780022A(A) PD780022AY PD780022AY(A) PD780023A PD780023A(A) PD780023AY PD780023AY(A) PD780024A PD780024A(A) PD780024AY PD780024AY(A) PD780031A PD780031A(A) PD780031AY PD780031AY(A) PD780032A PD780032A(A) PD780032AY PD780032AY(A) PD780033A PD780033A(A) PD780033AY PD780033AY(A) PD780034A PD780034A(A) PD780034AY PD780034AY(A) PD78F0034B PD78F0034B(A) PD78F0034BY PD78F0034BY(A) * To gain a general understanding of functions: Read this manual in the order of the CONTENTS. The mark shows major revised points. * How to interpret the register format: For a bit number enclosed in angle brackets, the bit name is defined as a reserved word in the RA78K0, and is defined as an sfr variable using the #pragma sfr directive in the CC78K0. * To check the details of a register when you know the register name: See APPENDIX D REGISTER INDEX. * To know the details of the 78K/0 Series instruction functions: Refer to the 78K/0 Series Instructions User's Manual (U12326E). * To know the electrical specifications of the PD780024A, 780034A, 780024AY, 780034AY Subseries: See CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: f X = 1.0 TO 12 MHz) and CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz). Caution Examples in this manual employ the "standard" quality grade for general electronics. When using examples in this manual for the "special" quality grade, review the quality grade of each part and/or circuit actually used. Differences between PD780024A, 780034A, 780024AY, and 780034AY Subseries The configuration of the serial interface and the resolution of the A/D converter differ on PD780024A, 780034A, 780024AY, and 780034AY Subseries products. Subseries PD780024A PD780034A PD780024AY PD780034AY Item Configuration of 3-wire serial I/O mode 2ch (SIO30, SIO31) 1ch (SIO30 only) serial interface UART mode 1ch 1ch I 2C None 1ch A/D converter 8 mode 8-bit resolution 10-bit resolution User's Manual U14046EJ5V0UD 8-bit resolution 10-bit resolution Chapter Organization This manual divides the descriptions for the subseries into different chapters as shown below. Read only the chapters related to the device you use. PD780024A PD780034A PD780024AY PD780034AY Subseries Subseries Subseries Subseries Chapter Chapter 1 Outline (PD780024A, 780034A Subseries) - - Chapter 2 Outline (PD780024AY, 780034AY Subseries) - - Chapter 3 Pin Function (PD780024A, 780034A Subseries) - - Chapter 4 Pin Function (PD780024AY, 780034AY Subseries) - - Chapter 5 CPU Architecture Chapter 6 Port Functions Chapter 7 Clock Generator Chapter 8 16-Bit Timer/Event Counter 0 Chapter 9 8-Bit Timer/Event Counters 50, 51 Chapter 10 Watch Timer Chapter 11 Watchdog Timer Chapter 12 Clock Output/Buzzer Output Controller Chapter 13 8-Bit A/D Converter (PD780024A, 780024AY Subseries) - - Chapter 14 10-Bit A/D Converter (PD780034A, 780034AY Subseries) - - Chapter 15 Serial Interface Outline Chapter 16 Serial Interface UART0 Chapter 17 Serial Interface SIO3 Chapter 18 Serial Interface IIC0 (PD780024AY, 780034AY Subseries only) - - Chapter 19 Interrupt Functions Chapter 20 External Device Expansion Function Chapter 21 Standby Function Chapter 22 Reset Function Chapter 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Chapter 24 Instruction Set Chapter 25 Electrical Specifications (Expanded-Specification Products: fX = 1.0 to 12 MHz) Chapter 26 Electrical Specifications (Conventional Products: fX = 1.0 to 8.38 MHz) Chapter 27 Package Drawings Chapter 28 Recommended Soldering Conditions Conventions Data significance: Higher digits on the left and lower digits on the right Active low representation: xxx (overscore over pin or signal name) Note: Footnote for item marked with Note in the text Caution: Information requiring particular attention Remark: Supplementary information Numerical representation: Binary Decimal *** xxxx or xxxxB *** xxxx Hexadecimal *** xxxxH User's Manual U14046EJ5V0UD 9 Related Documents The related documents indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. Documents Related to Devices Document Name Document No. PD780024A, 780034A, 780024AY, 780034AY Subseries User's Manual This manual 78K/0 Series Instructions User's Manual U12326E 78K/0 Series Basic (I) Application Note U12704E Documents Related to Development Tools (Software) (User's Manuals) Document Name RA78K0 Assembler Package Operation Document No. U16629E Language U14446E Structured Assembly Language U11789E CC78K0 C Compiler Operation U16613E Language U14298E SM78K Series Ver. 2.52 System Simulator Operation U16768E External Part User Open Interface Specifications U15802E ID78K0-NS Ver. 2.52 Integrated Debugger Operation U16488E RX78K0 Real-Time OS Basics U11537E Installation U11536E PM plus Ver. 5.10 U16569E Documents Related to Development Tools (Hardware) (User's Manuals) Document Name Document No. IE-78K0-NS In-Circuit Emulator U13731E IE-78K0-NS-A In-Circuit Emulator U14889E IE-78K0-NS-PA Performance Board To be prepared IE-780034-NS-EM1 Emulation Board U14642E IE-78001-R-A In-Circuit Emulator U14142E IE-78K0-R-EX1 In-Circuit Emulator To be prepared Documents Related to Flash Memory Programming Document Name Document No. PG-FP3 Flash Memory Programmer User's Manual U13502E PG-FP4 Flash Memory Programmer User's Manual U15260E Caution The related documents listed above are subject to change without notice. Be sure to use the latest version of each document for designing. 10 User's Manual U14046EJ5V0UD Other Documents Document Name Document No. SEMICONDUCTOR SELECTION GUIDE - Products and Packages - X13769X Semiconductor Device Mount Manual Note Quality Grades on NEC Semiconductor Devices C11531E NEC Semiconductor Device Reliability/Quality Control System C10983E Guide to Prevent Damage for Semiconductor Devices by Electrostatic Discharge (ESD) C11892E Note See the "Semiconductor Device Mount Manual" website (http://www.necel.com/pkg/en/mount/index.html). Caution The related documents listed above are subject to change without notice. Be sure to use the latest version of each document for designing. User's Manual U14046EJ5V0UD 11 CONTENTS CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) .................................................... 1.1 Expanded-Specification Products and Conventional Products ....................................... 1.2 Features ................................................................................................................................. 1.3 Applications .......................................................................................................................... 1.4 Ordering Information ............................................................................................................ 1.5 Quality Grade ........................................................................................................................ 1.6 Pin Configuration (Top View) ............................................................................................... 1.7 78K/0 Series Lineup .............................................................................................................. 1.8 Block Diagram ....................................................................................................................... 1.9 Outline of Function ............................................................................................................... 1.10 Correspondence Between Mask ROM Versions and Flash Memory Versions ............... 1.11 Differences Between Standard Grade Products and Special Grade Products ............... 1.12 Correspondence Between Products and Packages .......................................................... 1.13 Mask Options ........................................................................................................................ 20 20 21 22 23 30 37 41 43 44 46 46 47 47 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) .................................................. 2.1 Features ................................................................................................................................. 2.2 Applications .......................................................................................................................... 2.3 Ordering Information ............................................................................................................ 2.4 Quality Grade ........................................................................................................................ 2.5 Pin Configuration (Top View) ............................................................................................... 2.6 78K/0 Series Lineup .............................................................................................................. 2.7 Block Diagram ....................................................................................................................... 2.8 Outline of Function ............................................................................................................... 2.9 Correspondence Between Mask ROM Versions and Flash Memory Versions ............... 2.10 Differences Between Standard Grade Products and Special Grade Products ............... 2.11 Correspondence Between Products and Packages .......................................................... 2.12 Mask Options ........................................................................................................................ 48 48 49 50 57 64 68 70 71 72 73 73 74 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) .......................................... 3.1 Pin Function List ................................................................................................................... 3.2 Description of Pin Functions ............................................................................................... 75 75 78 12 3.2.1 P00 to P03 (Port 0) .................................................................................................................... 78 3.2.2 P10 to P17 (Port 1) .................................................................................................................... 78 3.2.3 P20 to P25 (Port 2) .................................................................................................................... 79 3.2.4 P30 to P36 (Port 3) .................................................................................................................... 79 3.2.5 P40 to P47 (Port 4) .................................................................................................................... 80 3.2.6 P50 to P57 (Port 5) .................................................................................................................... 80 3.2.7 P64 to P67 (Port 6) .................................................................................................................... 80 3.2.8 P70 to P75 (Port 7) .................................................................................................................... 81 3.2.9 AVREF .......................................................................................................................................... 81 3.2.10 AVDD ........................................................................................................................................... 81 3.2.11 AVSS ........................................................................................................................................... 81 3.2.12 RESET ....................................................................................................................................... 82 3.2.13 NC .............................................................................................................................................. 82 User's Manual U14046EJ5V0UD 3.2.14 X1 and X2 .................................................................................................................................. 82 3.2.15 XT1 and XT2 .............................................................................................................................. 82 3.2.16 VDD0 and VDD1 ............................................................................................................................. 82 3.2.17 VSS0 and VSS1 ............................................................................................................................. 82 3.2.18 VPP (flash memory versions only) .............................................................................................. 82 3.2.19 IC (mask ROM version only) ...................................................................................................... 82 Pin I/O Circuits and Recommended Connection of Unused Pins .................................... 83 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) ....................................... 4.1 Pin Function List ................................................................................................................... 4.2 Description of Pin Functions ............................................................................................... 87 87 90 3.3 4.2.1 P00 to P03 (Port 0) .................................................................................................................... 90 4.2.2 P10 to P17 (Port 1) .................................................................................................................... 90 4.2.3 P20 to P25 (Port 2) .................................................................................................................... 91 4.2.4 P30 to P36 (Port 3) .................................................................................................................... 91 4.2.5 P40 to P47 (Port 4) .................................................................................................................... 92 4.2.6 P50 to P57 (Port 5) .................................................................................................................... 92 4.2.7 P64 to P67 (Port 6) .................................................................................................................... 92 4.2.8 P70 to P75 (Port 7) .................................................................................................................... 93 4.2.9 AVREF .......................................................................................................................................... 93 4.2.10 AVDD ........................................................................................................................................... 93 4.2.11 AVSS ........................................................................................................................................... 93 4.2.12 RESET ....................................................................................................................................... 94 4.2.13 NC .............................................................................................................................................. 94 4.2.14 X1 and X2 .................................................................................................................................. 94 4.2.15 XT1 and XT2 .............................................................................................................................. 94 4.2.16 VDD0 and VDD1 ............................................................................................................................. 94 4.2.17 VSS0 and VSS1 ............................................................................................................................. 94 4.2.18 VPP (flash memory versions only) .............................................................................................. 94 4.2.19 IC (mask ROM version only) ...................................................................................................... 94 Pin I/O Circuits and Recommended Connection of Unused Pins .................................... 95 CHAPTER 5 CPU ARCHITECTURE ................................................................................................. 5.1 Memory Spaces ..................................................................................................................... 99 99 4.3 5.2 5.3 5.1.1 Internal program memory space ................................................................................................ 104 5.1.2 Internal data memory space ...................................................................................................... 106 5.1.3 Special function register (SFR) area .......................................................................................... 106 5.1.4 External memory space ............................................................................................................. 106 5.1.5 Data memory addressing ........................................................................................................... 107 Processor Registers ............................................................................................................. 112 5.2.1 Control registers ......................................................................................................................... 112 5.2.2 General-purpose registers ......................................................................................................... 116 5.2.3 Special function register (SFR) .................................................................................................. 117 Instruction Address Addressing ......................................................................................... 121 5.3.1 Relative addressing .................................................................................................................... 121 5.3.2 Immediate addressing ................................................................................................................ 122 5.3.3 Table indirect addressing ........................................................................................................... 123 5.3.4 Register addressing ................................................................................................................... 124 User's Manual U14046EJ5V0UD 13 5.4 Operand Address Addressing ............................................................................................. 125 5.4.1 Implied addressing ..................................................................................................................... 125 5.4.2 Register addressing ................................................................................................................... 126 5.4.3 Direct addressing ....................................................................................................................... 127 5.4.4 Short direct addressing .............................................................................................................. 128 5.4.5 Special function register (SFR) addressing ................................................................................ 129 5.4.6 Register indirect addressing ....................................................................................................... 130 5.4.7 Based addressing ...................................................................................................................... 131 5.4.8 Based indexed addressing ......................................................................................................... 132 5.4.9 Stack addressing ........................................................................................................................ 133 CHAPTER 6 PORT FUNCTIONS ...................................................................................................... 134 6.1 Port Functions ....................................................................................................................... 134 6.2 Port Configuration ................................................................................................................ 137 6.3 6.4 6.5 6.2.1 Port 0 .......................................................................................................................................... 137 6.2.2 Port 1 .......................................................................................................................................... 139 6.2.3 Port 2 .......................................................................................................................................... 140 6.2.4 Port 3 (PD780024A, 780034A Subseries) ............................................................................... 143 6.2.5 Port 3 (PD780024AY, 780034AY Subseries) ............................................................................ 148 6.2.6 Port 4 .......................................................................................................................................... 152 6.2.7 Port 5 .......................................................................................................................................... 153 6.2.8 Port 6 .......................................................................................................................................... 154 6.2.9 Port 7 .......................................................................................................................................... 156 Port Function Control Registers ......................................................................................... 159 Port Function Operations ..................................................................................................... 165 6.4.1 Writing to I/O port ....................................................................................................................... 165 6.4.2 Reading from I/O port ................................................................................................................ 165 6.4.3 Operations on I/O port ............................................................................................................... 165 Selection of Mask Option ..................................................................................................... 166 CHAPTER 7 CLOCK GENERATOR ................................................................................................. 7.1 Clock Generator Functions .................................................................................................. 7.2 Clock Generator Configuration ........................................................................................... 7.3 Clock Generator Control Registers ..................................................................................... 7.4 System Clock Oscillator ....................................................................................................... 7.5 7.6 167 167 167 169 173 7.4.1 Main system clock oscillator ....................................................................................................... 173 7.4.2 Subsystem clock oscillator ......................................................................................................... 174 7.4.3 When subsystem clock is not used ............................................................................................ 177 Clock Generator Operations ................................................................................................ 178 7.5.1 Main system clock operations .................................................................................................... 179 7.5.2 Subsystem clock operations ...................................................................................................... 180 Changing System Clock and CPU Clock Settings ............................................................. 180 7.6.1 Time required for switchover between system clock and CPU clock ......................................... 180 7.6.2 System clock and CPU clock switching procedure .................................................................... 181 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 .......................................................................... 182 8.1 Functions of 16-Bit Timer/Event Counter 0 ........................................................................ 182 8.2 Configuration of 16-Bit Timer/Event Counter 0 .................................................................. 183 14 User's Manual U14046EJ5V0UD 8.3 8.4 8.5 8.6 Registers to Control 16-Bit Timer/Event Counter 0 ........................................................... 186 Operation of 16-Bit Timer/Event Counter 0 ........................................................................ 192 8.4.1 Interval timer operation .............................................................................................................. 192 8.4.2 External event counter operation ............................................................................................... 195 8.4.3 Pulse width measurement operations ........................................................................................ 197 8.4.4 Square-wave output operation ................................................................................................... 204 8.4.5 PPG output operation ................................................................................................................. 205 Program List .......................................................................................................................... 207 8.5.1 Interval timer .............................................................................................................................. 208 8.5.2 Pulse width measurement by free-running counter and one capture register ............................ 209 8.5.3 Two pulse widths measurement by free-running counter ........................................................... 210 8.5.4 Pulse width measurement by restart .......................................................................................... 212 8.5.5 PPG output ................................................................................................................................. 213 Cautions Related to 16-Bit Timer/Event Counter 0 ............................................................ 214 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 ................................................................ 9.1 Functions of 8-Bit Timer/Event Counters 50, 51 ................................................................ 9.2 Configuration of 8-Bit Timer/Event Counters 50, 51 .......................................................... 9.3 Registers to Control 8-Bit Timer/Event Counters 50, 51 ................................................... 9.4 Operation of 8-Bit Timer/Event Counters 50, 51 ................................................................ 9.5 9.6 217 217 219 220 225 9.4.1 8-bit interval timer operation ....................................................................................................... 225 9.4.2 External event counter operation ............................................................................................... 229 9.4.3 Square-wave output (8-bit resolution) operation ........................................................................ 230 9.4.4 8-bit PWM output operation ....................................................................................................... 231 9.4.5 Interval timer (16-bit) operations ................................................................................................ 235 Program List .......................................................................................................................... 236 9.5.1 Interval timer (8-bit) .................................................................................................................... 236 9.5.2 External event counter ............................................................................................................... 237 9.5.3 Interval timer (16-bit) .................................................................................................................. 238 Cautions Related to 8-Bit Timer/Event Counters 50, 51 .................................................... 239 CHAPTER 10 WATCH TIMER .......................................................................................................... 10.1 Watch Timer Functions ........................................................................................................ 10.2 Watch Timer Configuration .................................................................................................. 10.3 Register to Control Watch Timer ......................................................................................... 10.4 Watch Timer Operations ...................................................................................................... 240 240 241 242 243 10.4.1 Watch timer operation ................................................................................................................ 243 10.4.2 Interval timer operation .............................................................................................................. 243 CHAPTER 11 WATCHDOG TIMER .................................................................................................. 11.1 Watchdog Timer Functions .................................................................................................. 11.2 Watchdog Timer Configuration ........................................................................................... 11.3 Registers to Control Watchdog Timer ................................................................................ 11.4 Watchdog Timer Operations ................................................................................................ 245 245 246 246 248 11.4.1 Watchdog timer operation .......................................................................................................... 248 11.4.2 Interval timer operation .............................................................................................................. 249 User's Manual U14046EJ5V0UD 15 CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER ............................................ 12.1 Clock Output/Buzzer Output Controller Functions ........................................................... 12.2 Configuration of Clock Output/Buzzer Output Controller ................................................. 12.3 Register to Control Clock Output/Buzzer Output Controller ............................................ 12.4 Operation of Clock Output/Buzzer Output Controller ....................................................... 250 250 251 251 254 12.4.1 Operation as clock output .......................................................................................................... 254 12.4.2 Operation as buzzer output ........................................................................................................ 254 CHAPTER 13 8-Bit A/D CONVERTER (PD780024A, 780024AY SUBSERIES) ........................ 13.1 A/D Converter Functions ...................................................................................................... 13.2 A/D Converter Configuration ............................................................................................... 13.3 Registers to Control A/D Converter .................................................................................... 13.4 A/D Converter Operations .................................................................................................... 255 255 257 259 262 13.4.1 Basic operations of A/D converter .............................................................................................. 262 13.4.2 Input voltage and conversion results .......................................................................................... 265 13.4.3 A/D converter operation mode ................................................................................................... 266 13.5 How to Read A/D Converter Characteristics Table ............................................................ 269 13.6 A/D Converter Cautions ....................................................................................................... 272 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) ...................... 14.1 A/D Converter Functions ...................................................................................................... 14.2 A/D Converter Configuration ............................................................................................... 14.3 Registers to Control A/D Converter .................................................................................... 14.4 A/D Converter Operation ...................................................................................................... 277 277 279 281 284 14.4.1 Basic operations of A/D converter .............................................................................................. 284 14.4.2 Input voltage and conversion results .......................................................................................... 287 14.4.3 A/D converter operation mode ................................................................................................... 288 14.5 How to Read A/D Converter Characteristics Table ............................................................ 290 14.6 A/D Converter Cautions ....................................................................................................... 293 CHAPTER 15 SERIAL INTERFACE OUTLINE ............................................................................... 298 CHAPTER 16 SERIAL INTERFACE UART0 ................................................................................... 16.1 Functions of Serial Interface UART0 ................................................................................... 16.2 Configuration of Serial Interface UART0 ............................................................................ 16.3 Registers to Control Serial Interface UART0 ...................................................................... 16.4 Operation of Serial Interface UART0 ................................................................................... 299 299 301 303 308 16.4.1 Operation stop mode .................................................................................................................. 308 16.4.2 Asynchronous serial interface (UART) mode ............................................................................. 308 16.4.3 Infrared data transfer mode ........................................................................................................ 319 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 ............................................................ 17.1 Functions of Serial Interfaces SIO30 and SIO31 ................................................................ 17.2 Configuration of Serial Interfaces SIO30 and SIO31 ......................................................... 17.3 Registers to Control Serial Interfaces SIO30 and SIO31 ................................................... 17.4 Operations of Serial Interfaces SIO30 and SIO31 .............................................................. 327 327 328 329 333 17.4.1 Operation stop mode .................................................................................................................. 333 17.4.2 3-wire serial I/O mode ................................................................................................................ 334 16 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) ..... 18.1 Functions of Serial Interface IIC0 ........................................................................................ 18.2 Configuration of Serial Interface IIC0 .................................................................................. 18.3 Registers to Control Serial Interface IIC0 ........................................................................... 18.4 I2C Bus Mode Functions ....................................................................................................... 338 338 341 343 353 18.4.1 Pin configuration ........................................................................................................................ 353 18.5 I2C Bus Definitions and Control Methods ........................................................................... 354 18.5.1 Start conditions .......................................................................................................................... 354 18.5.2 Addresses .................................................................................................................................. 355 18.5.3 Transfer direction specification ................................................................................................... 355 18.5.4 Acknowledge (ACK) signal ......................................................................................................... 356 18.5.5 Stop condition ............................................................................................................................ 357 18.5.6 Wait signal (WAIT) ..................................................................................................................... 358 18.5.7 Interrupt request (INTIIC0) generation timing and wait control .................................................. 360 18.5.8 Address match detection method .............................................................................................. 361 18.5.9 Error detection ............................................................................................................................ 361 18.5.10 Extension code ........................................................................................................................... 361 18.5.11 Arbitration ................................................................................................................................... 362 18.5.12 Wake-up function ....................................................................................................................... 363 18.5.13 Communication reservation ....................................................................................................... 364 18.5.14 Other cautions ............................................................................................................................ 366 18.5.15 Communication operations ........................................................................................................ 367 18.5.16 Timing of I2C interrupt request (INTIIC0) occurrence ................................................................. 375 18.6 Timing Charts ........................................................................................................................ 393 CHAPTER 19 INTERRUPT FUNCTIONS ......................................................................................... 19.1 Interrupt Function Types ...................................................................................................... 19.2 Interrupt Sources and Configuration .................................................................................. 19.3 Interrupt Function Control Registers .................................................................................. 19.4 Interrupt Servicing Operations ............................................................................................ 400 400 400 404 410 19.4.1 Non-maskable interrupt request acknowledgment operation ..................................................... 410 19.4.2 Maskable interrupt request acknowledgment operation ............................................................. 413 19.4.3 Software interrupt request acknowledgment operation .............................................................. 415 19.4.4 Nesting interrupt servicing ......................................................................................................... 416 19.4.5 Interrupt request hold ................................................................................................................. 419 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION ...................................................... 20.1 External Device Expansion Function .................................................................................. 20.2 External Device Expansion Function Control Registers ................................................... 20.3 External Device Expansion Function Timing ..................................................................... 20.4 Example of Connection with Memory ................................................................................. 420 420 423 425 430 CHAPTER 21 STANDBY FUNCTION ............................................................................................... 431 21.1 Standby Function and Configuration .................................................................................. 431 21.1.1 Standby function ........................................................................................................................ 431 21.1.2 Standby function control register ................................................................................................ 432 21.2 Standby Function Operations .............................................................................................. 433 21.2.1 HALT mode ................................................................................................................................ 433 21.2.2 STOP mode ............................................................................................................................... 436 User's Manual U14046EJ5V0UD 17 CHAPTER 22 RESET FUNCTION .................................................................................................... 439 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY .............................................. 23.1 Differences Between PD78F0034A, 78F0034AY and PD78F0034B, 78F0034BY ......... 23.2 Differences Between PD78F0034B, 78F0034BY and PD78F0034B(A), 78F0034BY(A) ........................................................................................................................ 23.3 Differences Between PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY and Mask ROM Versions ...................................................................................................... 23.4 Memory Size Switching Register ......................................................................................... 23.5 Flash Memory Characteristics ............................................................................................. 443 444 445 446 448 449 23.5.1 Programming environment ......................................................................................................... 449 23.5.2 Communication mode ................................................................................................................ 450 23.5.3 On-board pin processing ............................................................................................................ 455 23.5.4 Connection on adapter for flash memory writing ....................................................................... 458 CHAPTER 24 INSTRUCTION SET ................................................................................................... 470 24.1 Conventions .......................................................................................................................... 471 24.1.1 Operand identifiers and specification methods .......................................................................... 471 24.1.2 Description of "operation" column .............................................................................................. 472 24.1.3 Description of "flag operation" column ........................................................................................ 472 24.2 Operation List ........................................................................................................................ 473 24.3 Instructions Listed by Addressing Type ............................................................................ 481 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fx = 1.0 TO 12 MHz) .................... 485 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fx = 1.0 TO 8.38 MHz) ..................................... 516 CHAPTER 27 PACKAGE DRAWINGS ............................................................................................. 548 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS ........................................................ 554 APPENDIX A DIFFERENCES BETWEEN PD78018F, 780024A, 780034A, AND 780078 SUBSERIES ......................................................................................... 561 APPENDIX B DEVELOPMENT TOOLS ........................................................................................... B.1 Software Package ................................................................................................................. B.2 Language Processing Software .......................................................................................... B.3 Control Software ................................................................................................................... B.4 Flash Memory Writing Tools ................................................................................................ B.5 Debugging Tools (Hardware) ............................................................................................... B.6 B.7 B.8 B.9 18 564 567 567 568 569 569 B.5.1 When using in-circuit emulator IE-78K0-NS, IE-78K0-NS-A ...................................................... 569 B.5.2 When using in-circuit emulator IE-78001-R-A ............................................................................ 571 Debugging Tools (Software) ................................................................................................ Embedded Software ............................................................................................................. System Upgrade from Former In-Circuit Emulator for 78K/0 Series to IE-78001-R-A .... Package Drawings of Conversion Socket and Conversion Adapter ............................... User's Manual U14046EJ5V0UD 572 573 574 575 APPENDIX C NOTES ON TARGET SYSTEM DESIGN ................................................................ 581 APPENDIX D REGISTER INDEX ...................................................................................................... 591 D.1 Register Name Index ............................................................................................................ 591 D.2 Register Symbol Index ......................................................................................................... 594 APPENDIX E REVISION HISTORY .................................................................................................. 597 E.1 Major Revisions in This Edition ........................................................................................... 597 E.2 Revision History up to Previous Edition ............................................................................ 599 User's Manual U14046EJ5V0UD 19 OUTLINE (PD780024A, 780034A SUBSERIES) CHAPTER 1 1.1 Expanded-Specification Products and Conventional Products The expanded-specification products and conventional products refer to the following products. Expanded-specification products: PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A for which orders were received after December 1, 2001 (Products with a rankNote other than K, E, P, X) PD78F0034B Conventional products: Products other than the above expanded-specification products (Products with rankNote K, E, P, X) PD78F0034A Note The rank is indicated by the 5th digit from the left in the lot number marked on the package. Lot number Year code Week code Rank Expanded-specification products and conventional products differ in the operating frequency ratings. Power Supply Voltage (VDD) Guaranteed Operating Speed (Operating Frequency) Conventional Products Expanded-Specification Products 4.5 to 5.5 V 8.38 MHz (0.238 s) 12 MHz (0.166 s) 4.0 to 5.5 V 8.38 MHz (0.238 s) 8.38 MHz (0.238 s) 3.0 to 5.5 V 5 MHz (0.4 s) 8.38 MHz (0.238 s) 2.7 to 5.5 V 5 MHz (0.4 s) 5 MHz (0.4 s) 1.8 to 5.5 V 1.25 MHz (1.6 s) 1.25 MHz (1.6 s) Remark The parenthesized values indicate the minimum instruction execution time. Caution Only the conventional products are available in the PD780024AY and 780034AY Subseries (PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY). 20 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.2 Features * Internal memory Type Part Number Program Memory (ROM/Flash Memory) PD780021A, 780031A 8 KB PD780022A, 780032A 16 KB PD780023A, 780033A 24 KB PD780024A, 780034A 32 KB PD78F0034A, 78F0034B 32 KBNote Data Memory (High-Speed RAM) 512 bytes 1024 bytes 1024 bytesNote Note The capacities of internal flash memory and internal high-speed RAM can be changed by means of the memory size switching register (IMS). * * External memory expansion space: 64 KB Minimum instruction execution time changeable from high speed (expanded-specification product (0.166 s: @12 MHz operation with main system clock), conventional product (0.238 s: @ 8.38 MHz operation with main system clock)) to ultra-low speed (122 s: @ 32.768 kHz operation with subsystem clock) * Instruction set suited to system control * Bit manipulation possible in all address spaces * Multiply and divide instructions * * * * Fifty-one I/O ports: (Four N-ch open-drain ports) 8-bit resolution A/D converter: 8 channels (PD780024A Subseries only) 10-bit resolution A/D converter: 8 channels (PD780034A Subseries only) Serial interface: 3 channels * 3-wire serial I/O mode: 2 channels * UART mode: * 1 channel Timer: Five channels * 16-bit timer/event counter: 1 channel * 8-bit timer/event counter: 2 channels * * * * Watch timer: 1 channel * Watchdog timer: 1 channel Vectored interrupt sources: 20 Two types of on-chip clock oscillators (main system clock and subsystem clock) Power supply voltage: VDD = 1.8 to 5.5 V User's Manual U14046EJ5V0UD 21 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.3 Applications PD780021A, 780022A, 780023A, 780024A PD780031A, 780032A, 780033A, 780034A, 78F0034A, 78F0034B Home electric appliances, pagers, AV equipment, car audios, office automation equipment, etc. PD780021A(A), 780022A(A), 780023A(A), 780024A(A) PD780031A(A), 780032A(A), 780033A(A), 780034A(A), 78F0034B(A) Control of transportation equipment, gas detection breakers, safety devices, car electric equipment, etc. 22 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.4 Ordering Information (1) PD780024A Subseries (1/3) Part Number Package Internal ROM PD780021ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) PD780021ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780021AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780021AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780021AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780021AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780021AF1-xxx-CN3 Mask ROM 73-pin plastic FBGA (9 x 9) Mask ROM PD780021AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM PD780022ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780022AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780022AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780022AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780022AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780022AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 23 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (1) PD780024A Subseries (2/3) Part Number Package Internal ROM PD780023ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) PD780023ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780023AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780023AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780023AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780023AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780023AF1-xxx-CN3 Mask ROM 73-pin plastic FBGA (9 x 9) Mask ROM PD780023AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM PD780024ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780024ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780024AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780024AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780024AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780024AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780024AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780024AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. 24 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (1) PD780024A Subseries (3/3) Part Number Package Internal ROM PD780021ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780021AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780021AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780022ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780022AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780023ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780023AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780023AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780024ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780024AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780024AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM Note Under development Remark xxx indicates ROM code suffix. User's Manual U14046EJ5V0UD 25 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (1/4) Part Number PD780031ACW-xxx PD780031ACW-xxx-ANote 1 PD780031AGC-xxx-AB8 PD780031AGC-xxx-AB8-ANote 1 PD780031AGC-xxx-8BS PD780031AGC-xxx-8BS-A PD780031AGK-xxx-9ET PD780031AGK-xxx-9ET-ANote 2 PD780031AGB-xxx-8EU PD780031AGB-xxx-8EU-A PD780031AF1-xxx-CN3 PD780031AF1-xxx-CN3-ANote 2 PD780032ACW-xxx PD780032ACW-xxx-ANote 1 PD780032AGC-xxx-AB8 PD780032AGC-xxx-AB8-ANote 1 PD780032AGC-xxx-8BS PD780032AGC-xxx-8BS-A PD780032AGK-xxx-9ET PD780032AGK-xxx-9ET-A PD780032AGB-xxx-8EU PD780032AGB-xxx-8EU-A PD780032AF1-xxx-CN3 PD780032AF1-xxx-CN3-ANote 1 Package Internal ROM 64-pin plastic SDIP (19.05 mm (750)) Mask ROM 64-pin plastic SDIP (19.05 mm (750)) Mask ROM 64-pin plastic QFP (14x14) Mask ROM 64-pin plastic QFP (14x14) Mask ROM 64-pin plastic LQFP (14x14) Mask ROM 64-pin plastic LQFP (14x14) Mask ROM 64-pin plastic TQFP (12x12) Mask ROM 64-pin plastic TQFP (12x12) Mask ROM 64-pin plastic LQFP (10x10) Mask ROM 64-pin plastic LQFP (10x10) Mask ROM 73-pin plastic FBGA (9x9) Mask ROM 73-pin plastic FBGA (9x9) Mask ROM 64-pin plastic SDIP (19.05 mm (750)) Mask ROM 64-pin plastic SDIP (19.05 mm (750)) Mask ROM 64-pin plastic QFP (14x14) Mask ROM 64-pin plastic QFP (14x14) Mask ROM 64-pin plastic LQFP (14x14) Mask ROM 64-pin plastic LQFP (14x14) Mask ROM 64-pin plastic TQFP (12x12) Mask ROM 64-pin plastic TQFP (12x12) Mask ROM 64-pin plastic LQFP (10x10) Mask ROM 64-pin plastic LQFP (10x10) Mask ROM 73-pin plastic FBGA (9x9) Mask ROM 73-pin plastic FBGA (9x9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. 26 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (2/4) Part Number PD780033ACW-xxx Package Internal ROM 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780033ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780033AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780033AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780033AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780033AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780033AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780033AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM PD780034ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780034ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780034AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780034AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780034AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780034AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780034AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780034AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 27 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (3/4) Part Number Package Internal ROM PD78F0034ACW 64-pin plastic SDIP (19.05 mm (750)) Flash memory PD78F0034ACW-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Flash memory PD78F0034AGC-AB8Note 2 64-pin plastic QFP (14 x 14) Flash memory PD78F0034AGC-8BS 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034AGC-8BS-A 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034AGK-9ET 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034AGK-9ET-A 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034AGB-8EU 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034AGB-8EU-A 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BGC-8BS 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034BGC-8BS-A 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034BGK-9ET 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034BGK-9ET-A 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034BGB-8EU 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BGB-8EU-A 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BF1-CN3 73-pin plastic FBGA (9 x 9) Flash memory PD78F0034BF1-CN3-ANote 1 73-pin plastic FBGA (9 x 9) Flash memory Notes 1. Under planning 2. Maintenance product Remark Products with -A at the end of the part number are lead-free products. 28 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (4/4) Part Number Package Internal ROM PD780031ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780031AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780031AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780031AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780031AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780032ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780032AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780032AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780032AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780032AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780033ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780033AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780033AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780034ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780034AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780034AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD78F0034BGC(A)-8BS 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034BGK(A)-9ET 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034BGB(A)-8EU 64-pin plastic LQFP (10 x 10) Flash memory Note Under development Remark xxx indicates ROM code suffix. User's Manual U14046EJ5V0UD 29 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.5 Quality Grade (1) PD780024A Subseries (1/3) Part Number Package Quality Grades PD780021ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780021ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780021AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780021AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780021AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780021AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780021AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780021AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780021AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780021AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780021AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780021AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard PD780022ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780022ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780022AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780022AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780022AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780022AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780022AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780022AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780022AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780022AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780022AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780022AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 30 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (1) PD780024A Subseries (2/3) Part Number Package Quality Grades PD780023ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780023ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780023AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780023AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780023AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780023AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780023AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780023AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780023AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780023AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780023AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780023AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard PD780024ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780024ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780024AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780024AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780024AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780024AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780024AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780024AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780024AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780024AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780024AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780024AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 31 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (1) PD780024A Subseries (3/3) Part Number Package Quality Grades PD780021ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780021AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780021AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780021AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780021AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780022ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780022AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780022AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780022AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780022AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780023ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780023AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780023AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780023AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780023AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780024ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780024AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780024AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780024AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780024AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special Note Under development Remark xxx indicates ROM code suffix. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 32 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (1/4) Part Number Package Quality Grades PD780031ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780031ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780031AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780031AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780031AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780031AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780031AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780031AGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Standard PD780031AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780031AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780031AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780031AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard PD780032ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780032ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780032AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780032AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780032AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780032AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780032AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780032AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780032AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780032AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780032AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780032AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 33 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (2/4) Part Number Package Quality Grades PD780033ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780033ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780033AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780033AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780033AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780033AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780033AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780033AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780033AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780033AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780033AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780033AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard PD780034ACW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780034ACW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780034AGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780034AGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780034AGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780034AGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780034AGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780034AGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780034AGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780034AGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780034AF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780034AF1-xxx-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 34 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (3/4) Part Number Package Quality Grades PD78F0034ACW 64-pin plastic SDIP (19.05 mm (750)) Standard PD78F0034ACW-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD78F0034AGC-AB8Note 2 64-pin plastic QFP (14 x 14) Standard PD78F0034AGC-8BS 64-pin plastic LQFP (14 x 14) Standard PD78F0034AGC-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD78F0034AGK-9ET 64-pin plastic TQFP (12 x 12) Standard PD78F0034AGK-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD78F0034AGB-8EU 64-pin plastic LQFP (10 x 10) Standard PD78F0034AGB-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD78F0034BGC-8BS 64-pin plastic LQFP (14 x 14) Standard PD78F0034BGC-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD78F0034BGK-9ET 64-pin plastic TQFP (12 x 12) Standard PD78F0034BGK-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD78F0034BGB-8EU 64-pin plastic LQFP (10 x 10) Standard PD78F0034BGB-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD78F0034BF1-CN3 73-pin plastic FBGA (9 x 9) Standard PD78F0034BF1-CN3-ANote 1 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under development 2. Maintenance out product Remark Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 35 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2) PD780034A Subseries (4/4) Part Number Package Quality Grades PD780031ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780031AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780031AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780031AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780031AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780032ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780032AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780032AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780032AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780032AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780033ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780033AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780033AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780033AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780033AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780034ACW(A)-xxx 64-pin plastic SDIP (19.05 mm (750)) Special PD780034AGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780034AGC(A)-xxx-8BS 64-pin plastic LQFP (14 x 14) Special PD780034AGK(A)-xxx-9ET 64-pin plastic TQFP (12 x 12) Special PD780034AGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD78F0034BGC(A)-8BS 64-pin plastic LQFP (14 x 14) Special PD78F0034BGK(A)-9ET 64-pin plastic TQFP (12 x 12) Special PD78F0034BGB(A)-8EU 64-pin plastic LQFP (10 x 10) Special Note Under development Remark xxx indicates ROM code suffix. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 36 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.6 Pin Configuration (Top View) * 64-pin plastic SDIP (19.05 mm (750)) P40/AD0 1 64 P67/ASTB P41/AD1 2 63 P66/WAIT P42/AD2 3 62 P65/WR P43/AD3 4 61 P64/RD P44/AD4 5 60 P75/BUZ P45/AD5 6 59 P74/PCL P46/AD6 7 58 P73/TI51/TO51 P47/AD7 8 57 P72/TI50/TO50 P50/A8 9 56 P71/TI01 P51/A9 10 55 P70/TI00/TO0 P52/A10 11 54 P03/INTP3/ADTRG P53/A11 12 53 P02/INTP2 P54/A12 13 52 P01/INTP1 P55/A13 14 51 P00/INTP0 P56/A14 15 50 VSS1 P57/A15 16 49 X1 VSS0 17 48 X2 VDD0 18 47 IC (VPP) P30 19 46 XT1 P31 20 45 XT2 P32 21 44 RESET P33 22 43 AVDD P34/SI31 23 42 AVREF P35/SO31 24 41 P10/ANI0 P36/SCK31 25 40 P11/ANI1 P20/SI30 26 39 P12/ANI2 P21/SO30 27 38 P13/ANI3 P22/SCK30 28 37 P14/ANI4 P23/RxD0 29 36 P15/ANI5 P24/TxD0 30 35 P16/ANI6 P25/ASCK0 31 34 P17/ANI7 VDD1 32 33 AVSS Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024A, 780034A Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034A. User's Manual U14046EJ5V0UD 37 OUTLINE (PD780024A, 780034A SUBSERIES) CHAPTER 1 * 64-pin plastic QFP (14 x 14) * 64-pin plastic LQFP (14 x 14) * 64-pin plastic TQFP (12 x 12) P72/TI50/TO50 P73/TI51/TO51 P74/PCL P75/BUZ P64/RD P65/WR P66/WAIT P67/ASTB P40/AD0 P41/AD1 P42/AD2 P43/AD3 P44/AD4 P45/AD5 P46/AD6 P47/AD7 * 64-pin plastic LQFP (10 x 10) 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P50/A8 1 48 P71/TI01 P51/A9 2 47 P70/TI00/TO0 P52/A10 3 46 P03/INTP3/ADTRG P53/A11 4 45 P02/INTP2 P54/A12 5 44 P01/INTP1 P55/A13 6 43 P00/INTP0 P56/A14 7 42 VSS1 P57/A15 8 41 X1 VSS0 9 40 X2 VDD0 10 39 IC (VPP) P30 11 38 XT1 P31 12 37 XT2 P32 13 36 RESET P33 14 35 AVDD P34/SI31 15 34 AVREF P35/SO31 16 33 P10/ANI0 P11/ANI1 P12/ANI2 P13/ANI3 P14/ANI4 P15/ANI5 P16/ANI6 AVSS P17/ANI7 VDD1 P25/ASCK0 P24/TxD0 P23/RxD0 P22/SCK30 P21/SO30 P20/SI30 P36/SCK31 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024A, 780034A Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034A, 78F0034B. 38 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) * 73-pin plastic FBGA (9 x 9) Top View Bottom View 9 8 7 6 5 4 3 2 1 A B C D E F G H J J H G F E D C B A Index mark Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name A1 NC C1 P52/A10 E1 P57/A15 G1 P33 J1 NC A2 P46/AD6 C2 P53/A11 E2 VDD0 G2 P32 J2 P36/SCK31 A3 P44/AD4 C3 P45/AD5 E3 P54/A12 G3 P20/SI30 J3 NC A4 P41/AD1 C4 P42/AD2 E4 - G4 P21/SO30 J4 P25/ASCK0 A5 P67/ASTB C5 P64/RD E5 - G5 P24/TxD0 J5 NC A6 P65/WR C6 P73/TI51/TO51 E6 - G6 VDD1 J6 P17/ANI7 A7 P74/PCL C7 P03/INTP3/ADTRG E7 P00/INTP0 G7 P16/ANI6 J7 P12/ANI2 A8 NC C8 P01/INTP1 E8 XT1 G8 AVDD J8 P13/ANI3 A9 NC C9 VSS1 E9 X2 G9 NC J9 NC B1 P51/A9 D1 P55/A13 F1 P30 H1 P34/SI31 B2 P47/AD7 D2 P56/A14 F2 P31 H2 P35/SO31 B3 P43/AD3 D3 P50/A8 F3 VSS0 H3 P23/RxD0 B4 P40/AD0 D4 NC F4 - H4 P22/SCK30 B5 P66/WAIT D5 - F5 - H5 AVSS B6 P75/BUZ D6 - F6 - H6 P15/ANI5 B7 P72/TI50/TO51 D7 P02/INTP2 F7 P14/ANI4 H7 P11/ANI1 B8 P71/TI01 D8 IC (VPP) F8 RESET H8 P10/ANI0 B9 P70/TI00/TO0 D9 X1 F9 XT2 H9 AVREF Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024A, 780034A Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034B. User's Manual U14046EJ5V0UD 39 CHAPTER 1 A8 to A15: 40 OUTLINE (PD780024A, 780034A SUBSERIES) Address bus P64 to P67: Port 6 AD0 to AD7: Address/data bus P70 to P75: Port 7 ADTRG: AD trigger input PCL: Programmable clock ANI0 to ANI7: Analog input RD: Read strobe ASCK0: Asynchronous serial clock RESET: Reset ASTB: Address strobe RxD0: Receive data AVDD: Analog power supply SCK30, SCK31: Serial clock AVREF: Analog reference voltage SI30, SI31: Serial input AVSS: Analog ground SO30, SO31: Serial output BUZ: Buzzer clock TI00, TI01, TI50, TI51: Timer input IC: Internally connected TO0, TO50, TO51: Timer output INTP0 to INTP3: External interrupt input TxD0: Transmit data NC: VDD0, VDD1: Power supply Non-connection P00 to P03: Port 0 VPP: Programming power supply P10 to P17: Port 1 VSS0, VSS1: Ground P20 to P25: Port 2 WAIT: Wait P30 to P36: Port 3 WR: Write strobe P40 to P47: Port 4 X1, X2: Crystal (main system clock) P50 to P57: Port 5 XT1, XT2: Crystal (subsystem clock) User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.7 78K/0 Series Lineup The products in the 78K/0 Series are listed below. The names enclosed in boxes are subseries name. Products in mass production Products under development Y subseries products are compatible with I2C bus. Control EMI-noise reduced version of the PD78078 PD78075B PD78078 PD78070A PD78078Y PD78054 with timer and enhanced external interface PD78070AY 80-pin PD780058 PD780018AY PD780058Y ROMless version of the PD78078 PD78078Y with enhanced serial I/O and limited functions 80-pin PD78058F PD78054 PD780065 100-pin 100-pin 100-pin 100-pin 80-pin 80-pin 64-pin PD780078 64-pin 64-pin 52-pin PD780034A PD780024A PD780034AS 52-pin 64-pin PD780024AS PD78014H 64-pin 42/44-pin PD78018F PD78083 64-pin PD780988 PD78058FY PD78054 with enhanced serial I/O EMI-noise reduced version of the PD78054 PD78018F with UART and D/A converter, and enhanced I/O PD780024A with expanded RAM PD780034A with timer and enhanced serial I/O PD780078Y PD780034AY PD780024A with enhanced A/D converter PD780024AY PD78018F with enhanced serial I/O 52-pin version of the PD780034A PD78054Y 52-pin version of the PD780024A EMI-noise reduced version of the PD78018F PD78018FY Basic subseries for control On-chip UART, capable of operating at low voltage (1.8 V) Inverter control On-chip inverter controller and UART. EMI-noise reduced. VFD drive 78K/0 Series 100-pin PD780208 PD78044F with enhanced I/O and VFD C/D. Display output total: 53 80-pin For panel control. On-chip VFD C/D. Display output total: 53 80-pin PD780232 PD78044H 80-pin PD78044F Basic subseries for driving VFD. Display output total: 34 PD78044F with N-ch open-drain I/O. Display output total: 34 LCD drive PD780354 PD780344 PD780354Y PD780344 with enhanced A/D converter PD780344Y PD780308Y 100-pin PD780318 PD780308 PD78064B PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD78064 with enhanced SIO, and expanded ROM and RAM EMI-noise reduced version of the PD78064 100-pin PD78064 PD78064Y Basic subseries for driving LCDs, on-chip UART 100-pin 100-pin 120-pin 120-pin 120-pin 100-pin PD780338 PD780328 Segment signal output: 40 pins max. Segment signal output: 40 pins max. Segment signal output: 32 pins max. Segment signal output: 24 pins max. Bus interface supported 100-pin 80-pin PD780948 PD78098B PD78054 with IEBusTM controller PD780702Y PD780703AY PD780833Y 80-pin 80-pin 80-pin 64-pin On-chip CAN controller PD780816 On-chip IEBus controller On-chip CAN controller On-chip controller compliant with J1850 (Class 2) Specialized for CAN controller function Meter control 100-pin PD780958 80-pin PD780852 PD780828B 80-pin For industrial meter control On-chip automobile meter controller/driver For automobile meter driver. On-chip CAN controller Remark VFD (Vacuum Fluorescent Display) is referred to as FIPTM (Fluorescent Indicator Panel) in some documents, but the functions of the two are the same. User's Manual U14046EJ5V0UD 41 OUTLINE (PD780024A, 780034A SUBSERIES) CHAPTER 1 The major functional differences between the subseries are shown below. * Subseries without the suffix Y Function Subseries Name ROM Capacity Timer 8-Bit 16-Bit Watch WDT A/D PD78075B 32 KB to 40 KB Control PD78078 PD78070A 4 ch 1 ch 1 ch VDD External MIN. Expansion Value 1 ch 8 ch A/D - 88 1.8 V 61 2.7 V 3 ch (time-division UART: 1 ch) 68 1.8 V 3 ch (UART: 1 ch) 69 2.7 V Serial Interface D/A 2 ch 3 ch (UART: 1 ch) Yes 48 KB to 60 KB - PD780058 24 KB to 60 KB 2 ch PD78058F 48 KB to 60 KB PD78054 I/O 8-Bit 10-Bit 8-Bit 16 KB to 60 KB 2.0 V PD780065 40 KB to 48 KB - PD780078 48 KB to 60 KB 2 ch PD780034A 8 KB to 32 KB 1 ch - 8 ch PD780024A 8 ch - PD780034AS - 4 ch PD780024AS 4 ch - PD78014H 8 ch 4 ch (UART: 1 ch) 60 2.7 V 3 ch (UART: 2 ch) 52 1.8 V 3 ch (UART: 1 ch) 51 39 - 2 ch 53 Yes 1 ch (UART: 1 ch) 33 - PD78018F 8 KB to 60 KB PD78083 Inverter 8 KB to 16 KB - PD780988 16 KB to 60 KB 3 ch Note PD780208 32 KB to 60 KB 2 ch PD780232 16 KB to 24 KB PD78044H 32 KB to 48 KB - - 1 ch - 8 ch - 3 ch (UART: 2 ch) 47 4.0 V Yes 1 ch 1 ch 1 ch 8 ch - - 2 ch 74 2.7 V - 3 ch - - 4 ch 40 4.5 V 2 ch 1 ch 1 ch 8 ch 68 2.7 V 3 ch (UART: 1 ch) 66 1.8 V 10 ch 1 ch 2 ch (UART: 1 ch) 54 control VFD drive 1 ch PD78044F 16 KB to 40 KB LCD drive PD780354 24 KB to 32 KB 2 ch 4 ch 1 ch 3 ch 2 ch 1 ch 1 ch PD780344 - 8 ch PD780338 48 KB to 60 KB - 8 ch - - PD780328 62 PD780318 70 PD780308 48 KB to 60 KB 2 ch 1 ch 8 ch - - PD78064B 32 KB PD78064 Bus - 3 ch (time-division UART: 1 ch) 57 2.0 V 79 4.0 V Yes 69 2.7 V - 2 ch (UART: 1 ch) 16 KB to 32 KB PD780948 60 KB 2 ch interface PD78098B 40 KB to 60 KB 2 ch 1 ch 1 ch 8 ch - 1 ch supported PD780816 32 KB to 60 KB - 3 ch (UART: 1 ch) 2 ch - 2 ch (UART: 1 ch) 46 4.0 V Meter control PD780958 48 KB to 60 KB 4 ch 2 ch - 1 ch - - - 2 ch (UART: 1 ch) 69 2.2 V - Dashboard PD780852 32 KB to 40 KB 3 ch 1 ch 1 ch 1 ch 5 ch - - 3 ch (UART: 1 ch) 56 4.0 V - control PD780828B 32 KB to 60 KB Note 16-bit timer: 2 channels 2 ch 12 ch 59 10-bit timer: 1 channel 42 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.8 Block Diagram TI00/TO0/P70 16-bit timer/ event counter 0 Port 0 4 P00 to P03 TI50/TO50/P72 8-bit timer/ event counter 50 Port 1 8 P10 to P17 TI51/TO51/P73 8-bit timer/ event counter 51 Port 2 6 P20 to P25 Port 3 7 P30 to P36 Port 4 8 P40 to P47 Port 5 8 P50 to P57 Port 6 4 P64 to P67 Port 7 6 P70 to P75 TI01/P71 Watchdog timer Watch timer 78K/0 CPU core SI30/P20 SO30/P21 SCK30/P22 Serial interface SIO30 SI31/P34 SO31/P35 SCK31/P36 Serial interface SIO31 RAM RxD0/P23 TxD0/P24 ASCK0/P25 ANI0/P10 to ANI7/P17 AVDD AVSS AVREF INTP0/P00 to INTP3/P03 ROM (flash memory) UART0 8 8 8 External access A/D converter 4 Interrupt control AD0/P40 to AD7/P47 A8/P50 to A15/P57 RD/P64 WR/P65 WAIT/P66 ASTB/P67 RESET X1 BUZ/P75 System control Clock/buzzer output control PCL/P74 X2 XT1 VDD0 VDD1 VSS0 VSS1 IC (VPP) XT2 Remarks 1. The internal ROM and RAM capacities depend on the product. 2. Pin connection in parentheses is intended for the PD78F0034A, 78F0034B. User's Manual U14046EJ5V0UD 43 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.9 Outline of Function (1/2) PD780021A PD780031A PD780022A PD780032A PD780023A PD780033A PD780024A PD780034A PD78F0034A PD78F0034B ROM 8 KB (Mask ROM) 16 KB (Mask ROM) 24 KB (Mask ROM) 32 KB (Mask ROM) 32 KBNote (Flash memory) High-speed RAM 512 bytes Part Number Item Internal memory 1024 bytes Memory space 64 KB General-purpose register 8 bits x 32 registers (8 bits x 8 registers x 4 banks) Minimum instruction Minimum instruction execution time changeable function execution time 1024 bytesNote When main system clock selected * 0.166 s/0.333 s/0.666 s/1.33 s/2.66 s (@ 12 MHz operation, expanded-specification product only) * 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@ 8.38 MHz operation) When subsystem 122 s (@ 32.768 kHz operation) clock selected Instruction set * * * * 16-bit operation Multiply/divide (8 bits x 8 bits, 16 bits / 8 bits) Bit manipulate (set, reset, test, and Boolean operation) BCD adjust, etc. I/O port Total: * CMOS input: * CMOS I/O: * N-ch open-drain I/O (5 V breakdown): A/D converter * 8-bit resolution x 8 channels (PD780021A, 780022A, 780023A, 780024A) * 10-bit resolution x 8 channels (PD780031A, 780032A, 780033A, 780034A, 78F0034A, 78F0034B) * Low-voltage operation: AVDD = 1.8 to 5.5 V Serial interface * 3-wire serial I/O mode: * UART mode: Timer * 16-bit timer/event counter: 1 channel * 8-bit timer/event counter: 2 channels * Watch timer: 1 channel * Watchdog timer: 51 8 39 4 2 channels 1 channel 1 channel Timer output Three outputs (8-bit PWM output enable: 2) Clock output * 93.7 kHz, 187 kHz, 375 kHz, 750 kHz, 1.5 MHz, 3 MHz, 6 MHz, 12 MHz (12 MHz with main system clock, expanded-specification product only) * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (8.38 MHz with main system clock) * 32.768 kHz (32.768 kHz with subsystem clock) Buzzer output * 1.46 kHz, 2.92 kHz, 5.85 kHz, 11.7 kHz (12 MHz with main system clock, expanded-specification product only) * 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (8.38 MHz with main system clock) Vectored interrupt source Maskable Internal: 13, External: 5 Non-maskable Internal: 1 Software 1 Note The capacities of internal flash memory and internal high-speed RAM can be changed by means of the memory size switching register (IMS). 44 User's Manual U14046EJ5V0UD CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) (2/2) Item PD780021A PD780031A Power supply voltage VDD = 1.8 to 5.5 V Operating ambient temperature TA = -40 to +85C Package * * * * * * Part Number 64-pin 64-pin 64-pin 64-pin 64-pin 73-pin PD780022A PD780032A plastic plastic plastic plastic plastic plastic PD780023A PD780033A PD780024A PD780034A PD78F0034A PD78F0034B SDIP (19.05 mm (750)) QFP (14 x 14) LQFP (14 x 14) TQFP (12 x 12) LQFP (10 x 10) FBGA (9 x 9) (standard grade product only) The outline of the timer/event counter is as follows (for details, see CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0, CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51, CHAPTER 10 WATCH TIMER, and CHAPTER 11 WATCHDOG TIMER). 16-Bit Timer/ Event Counter 0 8-Bit Timer/ Event Counters 50, 51 Watch Timer Watchdog Timer 1 channel 2 channels 1 channelNote 1 1 channelNote 2 Operation Interval timer Mode External event counter - - Function Timer output - - PPG output - - - PWM output - - - Pulse width measurement - - - Square-wave output - - Interrupt request Notes 1. The watch timer can perform both watch timer and interval timer functions at the same time. 2. The watchdog timer can perform either the watchdog timer function or the interval timer function. User's Manual U14046EJ5V0UD 45 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.10 Correspondence Between Mask ROM Versions and Flash Memory Versions Table 1-1. Correspondence Between Mask ROM Versions and Flash Memory Versions PD780021A/2A/3A/4A PD780031A/2A/3A/4A Mask ROM Version PD780021A(A)/2A(A)/3A(A)/4A(A) PD780031A(A)/2A(A)/3A(A)/4A(A) Conventional Products ExpandedSpecification Products Conventional Products ExpandedSpecification Products PD78F0034A - - - PD78F0034B - - - - Note Flash Memory Version PD78F0034B(A) - Note The PD78F0034B(A) and the conventional products of the PD780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), and 780034A(A) differ in the operating frequency. When replacing a flash memory version with a mask ROM version, note the supply voltage and operating frequency. Remarks 1. : Supported, -: Not supported 2. The PD780034A and PD78F0034B, 78F0034B(A) differ in operating frequency ratings and the communication mode of flash memory programming. See 23.1 Differences Between PD78F0034A, 78F0034AY and PD78F0034B, 78F0034BY. 3. Expanded-specification products and conventional products of the PD780024A and 780034A Subseries differ in operating frequency ratings. For details, see CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) and CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz). 4. A special grade product of the PD78F0034A is not available. Only a standard grade product is available. 1.11 Differences Between Standard Grade Products and Special Grade Products The differences between standard grade products (PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A, 78F0034A, 78F0034B) and special grade products (PD780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), 780034A(A), 78F0034B(A)) are shown in Table 1-2. Table 1-2. Differences Between Standard Grade Products and Special Grade Products PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A, 78F0034A, 78F0034B PD780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), 780034A(A), 78F0034B(A) Quality grade Standard Package See 1.12 Correspondence Between Products and Packages Other (functions, electrical specifications, etc.) Same 46 User's Manual U14046EJ5V0UD Special CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) 1.12 Correspondence Between Products and Packages The following table shows the correspondence between the products and packages. Table 1-3. Correspondence Between Products and Packages Mask ROM Version Flash Memory Version PD780021A/2A/3A/4A PD780031A/2A/3A/4A Standard Special 64-pin SDIP (CW type) PD78F0034A PD78F0034B Standard Standard Special - - - - 64-pin QFP (GC-AB8 type) Note 1 64-pin LQFP (GC-8BS type) 64-pin TQFP (GK-9ET type) 64-pin LQFP (GB-8EU type) Note 2 73-pin FBGA (F1-CN3 type) - - - Notes 1. Maintenance product 2. Under development Remarks 1. : Package available, -: Package not available 2. A special grade product of the PD78F0034A is not available. Only a standard grade product is available. 1.13 Mask Options The mask ROM versions (PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, and 780034A) provide pull-up resistor mask options which allow users to specify whether to connect a pull-up resistor to a specific port pin when the user places an order for device production. Using the mask option when pull-up resistors are required reduces the number of components to add to the device, resulting in board space saving. The mask options provided in the PD780024A and 780034A Subseries are shown in Table 1-4. Table 1-4. Mask Options of Mask ROM Versions Pin Names Mask Option P30 to P33 Pull-up resistor connection can be specified in 1-bit units. User's Manual U14046EJ5V0UD 47 OUTLINE (PD780024AY, 780034AY SUBSERIES) CHAPTER 2 2.1 Features * Internal memory Type Program Memory (ROM/Flash Memory) Part Number PD780021AY, 780031AY 8 KB PD780022AY, 780032AY 16 KB PD780023AY, 780033AY 24 KB PD780024AY, 780034AY 32 KB PD78F0034AY, 78F0034BY 32 KBNote Data Memory (High-Speed RAM) 512 bytes 1024 bytes 1024 bytesNote Note The capacities of internal flash memory and internal high-speed RAM can be changed by means of the memory size switching register (IMS). * * External memory expansion space: 64 KB Minimum instruction execution time changeable from high speed (0.238 s: @ 8.38 MHz operation with main system clock) to ultra-low speed (122 s: @ 32.768 kHz operation with subsystem clock) * Instruction set suited to system control * Bit manipulation possible in all address spaces * Multiply and divide instructions * * * * Fifty-one I/O ports: (Four N-ch open-drain ports) 8-bit resolution A/D converter: 8 channels (PD780024AY Subseries only) 10-bit resolution A/D converter: 8 channels (PD780034AY Subseries only) Serial interface: 3 channels * 3-wire serial mode: 1 channel * UART mode: * * I 2C mode: 1 channel 1 channel Timer: Five channels * 16-bit timer/event counter: 1 channel * 8-bit timer/event counter: * * * 2 channels * Watch timer: 1 channel * Watchdog timer: 1 channel Vectored interrupt sources: 20 Two types of on-chip clock oscillators (main system clock and subsystem clock) Power supply voltage: VDD = 1.8 to 5.5 V Caution Only the conventional products are available in the PD780024AY and 780034AY Subseries (for details of conventional products, see 1.1 Expanded-Specification Products and Conventional Products). 48 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.2 Applications PD780021AY, 780022AY, 780023AY, 780024AY PD780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY Home electric appliances, pagers, AV equipment, car audios, office automation equipment, etc. PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A) PD780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A), 78F0034BY(A) Control of transportation equipment, gas detection breakers, safety devices, car electric equipment, etc. User's Manual U14046EJ5V0UD 49 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.3 Ordering Information (1) PD780024AY Subseries (1/3) Part Number Package Internal ROM PD780021AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780021AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780021AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780021AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780021AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780021AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780021AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780022AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780022AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780022AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780022AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780022AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. 50 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (1) PD780024AY Subseries (2/3) Part Number Package Internal ROM PD780023AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780023AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780023AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780023AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780023AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780023AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780023AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780024AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780024AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780024AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780024AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780024AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780024AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780024AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 51 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (1) PD780024AY Subseries (3/3) Part Number PD780021AYCW(A)-xxxNote Package 64-pin plastic SDIP (19.05 mm (750)) PD780021AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Internal ROM Mask ROM Mask ROM PD780021AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780021AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780021AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780022AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780022AYGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780022AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780022AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780022AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780023AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) PD780023AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Mask ROM Mask ROM PD780023AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780023AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780023AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780024AYCW(A)-xxxNote Mask ROM 64-pin plastic SDIP (19.05 mm (750)) PD780024AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Mask ROM PD780024AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780024AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780024AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM Note Under development Remark xxx indicates ROM code suffix. 52 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (1/4) Part Number Package Internal ROM PD780031AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780031AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780031AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780031AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780031AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780031AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780031AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780031AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Mask ROM PD780031AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780031AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780031AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780032AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780032AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780032AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780032AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780032AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780032AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780032AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780032AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780032AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780032AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780032AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 53 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (2/4) Part Number Package Internal ROM PD780033AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780033AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780033AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780033AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780033AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780033AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780033AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM PD780034AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780034AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Mask ROM PD780034AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Mask ROM PD780034AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Mask ROM PD780034AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Mask ROM PD780034AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Mask ROM PD780034AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Mask ROM Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. 54 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (3/4) Part Number Package Internal ROM PD78F0034AYCW 64-pin plastic SDIP (19.05 mm (750)) Flash memory PD78F0034AYCW-ANote 2 64-pin plastic SDIP (19.05 mm (750)) Flash memory PD78F0034AYGC-AB8 64-pin plastic QFP (14 x 14) Flash memory PD78F0034AYGC-AB8-ANote 1 64-pin plastic QFP (14 x 14) Flash memory PD78F0034AYGC-8BS 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034AYGC-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034AYGK-9ET 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034AYGK-9ET-ANote 1 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034AYGB-8EU 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034AYGB-8EU-A 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BYGC-8BS 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034BYGC-8BS-A 64-pin plastic LQFP (14 x 14) Flash memory PD78F0034BYGK-9ET 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034BYGK-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Flash memory PD78F0034BYGB-8EU 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BYGB-8EU-A 64-pin plastic LQFP (10 x 10) Flash memory PD78F0034BYF1-CN3 73-pin plastic FBGA (9 x 9) Flash memory PD78F0034BYF1-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Flash memory Notes 1. Under planning 2. Under development Remark Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 55 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (4/4) Part Number PD780031AYCW(A)-xxxNote Package 64-pin plastic SDIP (19.05 mm (750)) PD780031AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Internal ROM Mask ROM Mask ROM PD780031AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780031AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780031AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780032AYCW(A)-xxxNote Mask ROM 64-pin plastic SDIP (19.05 mm (750)) PD780032AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Mask ROM PD780032AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780032AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780032AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780033AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) PD780033AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Mask ROM Mask ROM PD780033AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780033AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780033AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD780034AYCW(A)-xxxNote Mask ROM 64-pin plastic SDIP (19.05 mm (750)) PD780034AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Mask ROM PD780034AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Mask ROM PD780034AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Mask ROM PD780034AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Mask ROM PD78F0034BYGC(A)-8BS 64-pin plastic LQFP (14 x 14) Mask ROM PD78F0034BYGK(A)-9ET 64-pin plastic TQFP (12 x 12) Mask ROM PD78F0034BYGB(A)-8EU 64-pin plastic LQFP (10 x 10) Mask ROM Note Under development Remark xxx indicates ROM code suffix. 56 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.4 Quality Grade (1) PD780024AY Subseries (1/3) Part Number Package Quality Grades PD780021AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780021AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780021AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780021AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780021AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780021AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Standard PD780021AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780021AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Standard PD780021AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780021AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780021AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780022AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780022AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780022AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780022AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780022AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780022AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Standard PD780022AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780022AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780022AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780022AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780022AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 57 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (1) PD780024AY Subseries (2/3) Part Number Package Quality Grades PD780023AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780023AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780023AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780023AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780023AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780023AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Standard PD780023AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780023AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780023AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780023AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780023AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780024AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780024AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780024AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780024AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780024AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780024AYGC-xxx-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Standard PD780024AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780024AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780024AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780024AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780024AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 58 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (1) PD780024AY Subseries (3/3) Part Number PD780021AYCW(A)-xxxNote Package 64-pin plastic SDIP (19.05 mm (750)) PD780021AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Quality Grades Special Special PD780021AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780021AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780021AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780022AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) Special PD780022AYGC(A)-xxx-AB8 64-pin plastic QFP (14 x 14) Special PD780022AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780022AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780022AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780023AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) PD780023AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Special Special PD780023AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780023AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780023AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780024AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) Special PD780024AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Special PD780024AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780024AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780024AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special Note Under development Remark xxx indicates ROM code suffix. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 59 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (1/4) Part Number Package Quality Grades PD780031AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780031AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780031AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780031AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780031AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780031AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780031AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780031AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Standard PD780031AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780031AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780031AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780032AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780032AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780032AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780032AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780032AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780032AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780032AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780032AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780032AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780032AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780032AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 60 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (2/4) Part Number Package Quality Grades PD780033AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780033AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780033AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780033AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780033AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780033AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780033AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780033AYGK-xxx-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Standard PD780033AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780033AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780033AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard PD780034AYCW-xxx 64-pin plastic SDIP (19.05 mm (750)) Standard PD780034AYCW-xxx-ANote 1 64-pin plastic SDIP (19.05 mm (750)) Standard PD780034AYGC-xxx-AB8 64-pin plastic QFP (14 x 14) Standard PD780034AYGC-xxx-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD780034AYGC-xxx-8BS 64-pin plastic LQFP (14 x 14) Standard PD780034AYGC-xxx-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD780034AYGK-xxx-9ET 64-pin plastic TQFP (12 x 12) Standard PD780034AYGK-xxx-9ET-A 64-pin plastic TQFP (12 x 12) Standard PD780034AYGB-xxx-8EU 64-pin plastic LQFP (10 x 10) Standard PD780034AYGB-xxx-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD780034AYF1-xxx-CN3 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remarks 1. xxx indicates ROM code suffix. 2. Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 61 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (3/4) Part Number Package Quality Grades PD78F0034AYCW 64-pin plastic SDIP (19.05 mm (750)) Standard PD78F0034AYCW-ANote 2 64-pin plastic SDIP (19.05 mm (750)) Standard PD78F0034AYGC-AB8 64-pin plastic QFP (14 x 14) Standard PD78F0034AYGC-AB8-ANote 1 64-pin plastic QFP (14 x 14) Standard PD78F0034AYGC-8BS 64-pin plastic LQFP (14 x 14) Standard PD78F0034AYGC-8BS-ANote 2 64-pin plastic LQFP (14 x 14) Standard PD78F0034AYGK-9ET 64-pin plastic TQFP (12 x 12) Standard PD78F0034AYGK-9ET-ANote 1 64-pin plastic TQFP (12 x 12) Standard PD78F0034AYGB-8EU 64-pin plastic LQFP (10 x 10) Standard PD78F0034AYGB-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD78F0034BYGC-8BS 64-pin plastic LQFP (14 x 14) Standard PD78F0034BYGC-8BS-A 64-pin plastic LQFP (14 x 14) Standard PD78F0034BYGK-9ET 64-pin plastic TQFP (12 x 12) Standard PD78F0034BYGK-9ET-ANote 2 64-pin plastic TQFP (12 x 12) Standard PD78F0034BYGB-8EU 64-pin plastic LQFP (10 x 10) Standard PD78F0034BYGB-8EU-A 64-pin plastic LQFP (10 x 10) Standard PD78F0034BYF1-CN3 73-pin plastic FBGA (9 x 9) Standard PD78F0034BYF1-CN3-ANote 2 73-pin plastic FBGA (9 x 9) Standard Notes 1. Under planning 2. Under development Remark Products with -A at the end of the part number are lead-free products. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. 62 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) (2) PD780034AY Subseries (4/4) Part Number PD780031AYCW(A)-xxxNote Package 64-pin plastic SDIP (19.05 mm (750)) PD780031AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Quality Grades Special Special PD780031AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780031AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780031AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780032AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) Special PD780032AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Special PD780032AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780032AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780032AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780033AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) PD780033AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Special Special PD780033AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780033AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780033AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD780034AYCW(A)-xxxNote 64-pin plastic SDIP (19.05 mm (750)) Special PD780034AYGC(A)-xxx-AB8Note 64-pin plastic QFP (14 x 14) Special PD780034AYGC(A)-xxx-8BSNote 64-pin plastic LQFP (14 x 14) Special PD780034AYGK(A)-xxx-9ETNote 64-pin plastic TQFP (12 x 12) Special PD780034AYGB(A)-xxx-8EUNote 64-pin plastic LQFP (10 x 10) Special PD78F0034BYGC(A)-8BS 64-pin plastic LQFP (14 x 14) Special PD78F0034BYGK(A)-9ET 64-pin plastic TQFP (12 x 12) Special PD78F0034BYGB(A)-8EU 64-pin plastic LQFP (10 x 10) Special Note Under development Remark xxx indicates ROM code suffix. Please refer to "Quality Grades on NEC Semiconductor Devices" (Document No. C11531E) published by NEC Electronics Corporation to know the specification of the quality grade on the device and its recommended applications. User's Manual U14046EJ5V0UD 63 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.5 Pin Configuration (Top View) * 64-pin plastic SDIP (19.05 mm (750)) P40/AD0 1 64 P67/ASTB P41/AD1 2 63 P66/WAIT P42/AD2 3 62 P65/WR P43/AD3 4 61 P64/RD P44/AD4 5 60 P75/BUZ P45/AD5 6 59 P74/PCL P46/AD6 7 58 P73/TI51/TO51 P47/AD7 8 57 P72/TI50/TO50 P50/A8 9 56 P71/TI01 P51/A9 10 55 P70/TI00/TO0 P52/A10 11 54 P03/INTP3/ADTRG P53/A11 12 53 P02/INTP2 P54/A12 13 52 P01/INTP1 P55/A13 14 51 P00/INTP0 P56/A14 15 50 VSS1 P57/A15 16 49 X1 VSS0 17 48 X2 VDD0 18 47 IC (VPP) P30 19 46 XT1 P31 P32/SDA0 20 21 45 44 XT2 RESET P33/SCL0 22 43 AVDD P34 23 42 AVREF P35 24 41 P10/ANI0 P36 25 40 P11/ANI1 P20/SI30 26 39 P12/ANI2 P21/SO30 27 38 P13/ANI3 P22/SCK30 28 37 P14/ANI4 P23/RxD0 29 36 P15/ANI5 P24/TxD0 30 35 P16/ANI6 P25/ASCK0 31 34 P17/ANI7 VDD1 32 33 AVSS Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024AY, 780034AY Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034AY. 64 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) * 64-pin plastic QFP (14 x 14) * 64-pin plastic LQFP (14 x 14) * 64-pin plastic TQFP (12 x 12) P72/TI50/TO50 P73/TI51/TO51 P74/PCL P75/BUZ P64/RD P65/WR P66/WAIT P67/ASTB P40/AD0 P41/AD1 P42/AD2 P43/AD3 P44/AD4 P45/AD5 P46/AD6 P47/AD7 * 64-pin plastic LQFP (10 x 10) P54/A12 5 44 P01/INTP1 P55/A13 6 43 P00/INTP0 P56/A14 7 42 VSS1 P57/A15 8 41 X1 VSS0 9 40 X2 VDD0 10 39 IC (VPP) P30 11 38 XT1 P31 12 37 XT2 P32/SDA0 13 36 RESET P33/SCL0 14 35 AVDD P34 15 34 AVREF P35 16 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 P71/TI01 P10/ANI0 P11/ANI1 P12/ANI2 P02/INTP2 P13/ANI3 45 P14/ANI4 4 P15/ANI5 P53/A11 P16/ANI6 P03/INTP3/ADTRG P17/ANI7 46 AVSS 3 VDD1 P52/A10 P25/ASCK0 P70/TI00/TO0 P24/TxD0 47 P23/RxD0 2 P22/SCK30 P51/A9 P21/SO30 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 P36 1 P20/SI30 P50/A8 Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024AY, 780034AY Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034AY, 78F0034BY. User's Manual U14046EJ5V0UD 65 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) * 73-pin plastic FBGA (9 x 9) Top View Bottom View 9 8 7 6 5 4 3 2 1 A B C D E F G H J J H G F E D C B A Index mark Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name A1 NC C1 P52/A10 E1 P57/A15 G1 P33/SCL0 J1 NC A2 P46/AD6 C2 P53/A11 E2 VDD0 G2 P32/SDA0 J2 P36 A3 P44/AD4 C3 P45/AD5 E3 P54/A12 G3 P20/SI30 J3 NC A4 P41/AD1 C4 P42/AD2 E4 - G4 P21/SO30 J4 P25/ASCK0 A5 P67/ASTB C5 P64/RD E5 - G5 P24/TxD0 J5 NC A6 P65/WR C6 P73/TI51/TO51 E6 - G6 VDD1 J6 P17/ANI7 A7 P74/PCL C7 P03/INTP3/ADTRG E7 P00/INTP0 G7 P16/ANI6 J7 P12/ANI2 A8 NC C8 P01/INTP1 E8 XT1 G8 AVDD J8 P13/ANI3 A9 NC C9 VSS1 E9 X2 G9 NC J9 NC B1 P51/A9 D1 P55/A13 F1 P30 H1 P34 B2 P47/AD7 D2 P56/A14 F2 P31 H2 P35 B3 P43/AD3 D3 P50/A8 F3 VSS0 H3 P23/RxD0 B4 P40/AD0 D4 NC F4 - H4 P22/SCK30 B5 P66/WAIT D5 - F5 - H5 AVSS B6 P75/BUZ D6 - F6 - H6 P15/ANI5 B7 P72/TI50/TO51 D7 P02/INTP2 F7 P14/ANI4 H7 P11/ANI1 B8 P71/TI01 D8 IC (VPP) F8 RESET H8 P10/ANI0 B9 P70/TI00/TO0 D9 X1 F9 XT2 H9 AVREF Cautions 1. Connect the IC (Internally Connected) pin directly to VSS0 or VSS1. 2. Connect the AVSS pin to VSS0. Remarks 1. When the PD780024AY, 780034AY Subseries products are used in applications where the noise generated inside the microcontroller needs to be reduced, the implementation of noise reduction measures, such as supplying voltage to VDD0 and VDD1 individually and connecting VSS0 and VSS1 to different ground lines, is recommended. 2. Pin connection in parentheses is intended for the PD78F0034BY. 66 User's Manual U14046EJ5V0UD CHAPTER 2 A8 to A15: OUTLINE (PD780024AY, 780034AY SUBSERIES) Address bus P70 to P75: Port 7 AD0 to AD7: Address/data bus PCL: Programmable clock ADTRG: AD trigger input RD: Read strobe ANI0 to ANI7: Analog input RESET: Reset ASCK0: Asynchronous serial clock RxD0: Receive data ASTB: Address strobe SCK30: Serial clock AVDD: Analog power supply SCL0: Serial clock AVREF: Analog reference voltage SDA0: Serial data AVSS: Analog ground SI30: Serial input BUZ: Buzzer clock SO30: Serial output IC: Internally connected TI00, TI01, TI50, TI51: Timer input INTP0 to INTP3: External interrupt input TO0, TO50, TO51: Timer output NC: Non-connection TxD0: Transmit data P00 to P03: Port 0 VDD0, VDD1: Power supply P10 to P17: Port 1 VPP: Programming power supply P20 to P25: Port 2 VSS0, VSS1: Ground P30 to P36: Port 3 WAIT: Wait P40 to P47: Port 4 WR: Write strobe P50 to P57: Port 5 X1, X2: Crystal (main system clock) P64 to P67: Port 6 XT1, XT2: Crystal (subsystem clock) User's Manual U14046EJ5V0UD 67 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.6 78K/0 Series Lineup The products in the 78K/0 Series are listed below. The names enclosed in boxes are subseries name. Products in mass production Products under development Y subseries products are compatible with I2C bus. Control EMI-noise reduced version of the PD78078 PD78075B PD78078 PD78070A PD78078Y PD78054 with timer and enhanced external interface PD78070AY 80-pin PD780058 PD780018AY PD780058Y ROMless version of the PD78078 PD78078Y with enhanced serial I/O and limited functions 80-pin PD78058F PD78054 PD780065 100-pin 100-pin 100-pin 100-pin 80-pin 80-pin 64-pin PD780078 64-pin 64-pin 52-pin PD780034A PD780024A PD780034AS 52-pin 64-pin PD780024AS PD78014H 64-pin PD78018F PD78083 42/44-pin PD78058FY PD78054 with enhanced serial I/O EMI-noise reduced version of the PD78054 PD78018F with UART and D/A converter, and enhanced I/O PD780024A with expanded RAM PD780034A with timer and enhanced serial I/O PD780078Y PD780034AY PD780024A with enhanced A/D converter PD780024AY PD78018F with enhanced serial I/O 52-pin version of the PD780034A PD78054Y 52-pin version of the PD780024A EMI-noise reduced version of the PD78018F PD78018FY Basic subseries for control On-chip UART, capable of operating at low voltage (1.8 V) Inverter control 64-pin PD780988 On-chip inverter controller and UART. EMI-noise reduced. VFD drive 78K/0 Series 100-pin PD780208 PD78044F with enhanced I/O and VFD C/D. Display output total: 53 80-pin For panel control. On-chip VFD C/D. Display output total: 53 80-pin PD780232 PD78044H 80-pin PD78044F Basic subseries for driving VFD. Display output total: 34 PD78044F with N-ch open-drain I/O. Display output total: 34 LCD drive PD780354 PD780344 PD780354Y PD780344 with enhanced A/D converter PD780344Y PD780308Y 100-pin PD780318 PD780308 PD78064B PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD780308 with enhanced display function and timer. PD78064 with enhanced SIO, and expanded ROM and RAM EMI-noise reduced version of the PD78064 100-pin PD78064 PD78064Y Basic subseries for driving LCDs, on-chip UART 100-pin 100-pin 120-pin 120-pin 120-pin 100-pin PD780338 PD780328 Segment signal output: 40 pins max. Segment signal output: 40 pins max. Segment signal output: 32 pins max. Segment signal output: 24 pins max. Bus interface supported 100-pin 80-pin PD780948 PD78098B PD78054 with IEBus controller PD780702Y PD780703AY PD780833Y 80-pin 80-pin 80-pin 64-pin On-chip CAN controller PD780816 On-chip IEBus controller On-chip CAN controller On-chip controller compliant with J1850 (Class 2) Specialized for CAN controller function Meter control 100-pin PD780958 80-pin PD780852 PD780828B 80-pin For industrial meter control On-chip automobile meter controller/driver For automobile meter driver. On-chip CAN controller Remark VFD (Vacuum Fluorescent Display) is referred to as FIP (Fluorescent Indicator Panel) in some documents, but the functions of the two are the same. 68 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) The major functional differences between the subseries are shown below. * Subseries with the suffix Y Function Subseries Name Control PD78078Y PD78070AY ROM Capacity 48 KB to 60 KB Timer 8-Bit 10-Bit 8-Bit 8-Bit 16-Bit Watch WDT A/D 4 ch 1 ch 1 ch 1 ch 8 ch A/D - I2C: 1 ch) PD780018AY 48 KB to 60 KB 24 KB to 60 KB PD78058FY - 2 ch Bus 3 ch (I2C: 1 ch) 88 1.8 V 61 2.7 V 48 KB to 60 KB 3 ch (UART: 1 ch, 2.7 V PD78054Y 16 KB to 60 KB I2C: 1 ch) PD780078Y 48 KB to 60 KB - 2 ch 8 KB to 60 KB PD780354Y 24 KB to 32 KB 4 ch 1 ch 1 ch PD780344Y 1 ch - 8 ch PD780308Y 48 KB to 60 KB PD78064Y 16 KB to 32 KB PD780702Y 60 KB - 1 ch 8 ch PD78018FY 8 ch Yes 69 2.0 V 4 ch (UART: 2 ch, I2C: 1 ch) 52 3 ch (UART: 1 ch, 51 1.8 V I2C: 1 ch) - 8 ch External 88 1.8 V PD780024AY drive VDD 2 ch 3 ch (time-division 68 UART: 1 ch, I2C: 1 ch) PD780034AY 8 KB to 32 KB LCD I/O MIN. Value Expansion 2 ch 3 ch (UART: 1 ch, - PD780058Y Serial Interface D/A - 2 ch (I2C: 1 ch) 53 4 ch (UART: 1 ch, 66 1.8 V 3 ch (time-division 57 UART: 1 ch, I2C: 1 ch) 2.0 V I2C: - 2 ch - 1 ch) 2 ch (UART: 1 ch, I2C: 1 ch) 3 ch 2 ch 1 ch 1 ch 16 ch - - 4 ch (UART: 1 ch, 67 3.5 V 65 4.5 V - I2C: 1 ch) interface PD780703AY 59.5 KB supported PD780833Y 60 KB Remark The functions of the subseries without the suffix Y and the subseries with the suffix Y are the same, except for the serial interface (if a subseries without the suffix Y is available). User's Manual U14046EJ5V0UD 69 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.7 Block Diagram TI00/TO0/P70 16-bit timer/ event counter 0 Port 0 4 P00 to P03 TI50/TO50/P72 8-bit timer/ event counter 50 Port 1 8 P10 to P17 TI51/TO51/P73 8-bit timer/ event counter 51 Port 2 6 P20 to P25 Watchdog timer Port 3 7 P30 to P36 Port 4 8 P40 to P47 Port 5 8 P50 to P57 Port 6 4 P64 to P67 Port 7 6 P70 to P75 TI01/P71 Watch timer SI30/P20 SO30/P21 SCK30/P22 78K/0 CPU core ROM (flash memory) Serial interface SIO30 RxD0/P23 TxD0/P24 ASCK0/P25 UART0 RAM SDA0/P32 2 I C bus 8 SCL0/P33 8 ANI0/P10 to ANI7/P17 AVDD AVSS AVREF INTP0/P00 to INTP3/P03 8 External access A/D converter 4 Clock/buzzer output control System control VDD0 VDD1 VSS0 VSS1 IC (VPP) Remarks 1. The internal ROM and RAM capacities depend on the product. 2. Pin connection in parentheses is intended for the PD78F0034AY, 78F0034BY. 70 RD/P64 WR/P65 WAIT/P66 ASTB/P67 Interrupt control BUZ/P75 PCL/P74 AD0/P40 to AD7/P47 A8/P50 to A15/P57 User's Manual U14046EJ5V0UD RESET X1 X2 XT1 XT2 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.8 Outline of Function Part Number Item Internal memory PD780021AY PD780022AY PD780023AY PD780024AY PD78F0034AY PD780031AY PD780032AY PD780033AY PD780034AY PD78F0034BY ROM 8 KB (Mask ROM) High-speed RAM 512 bytes 16 KB (Mask ROM) 24 KB (Mask ROM) 32 KB (Mask ROM) 1024 bytes Memory space 64 KB General-purpose register 8 bits x 32 registers (8 bits x 8 registers x 4 banks) Minimum instruction Minimum instruction execution time changeable function execution time 32 KBNote (Flash memory) 1024 bytesNote When main system clock selected 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@ 8.38 MHz operation) When subsystem clock selected 122 s (@ 32.768 kHz operation) Instruction set * * * * I/O port Total: * CMOS input: * CMOS I/O: * N-ch open-drain I/O (5 V breakdown): A/D converter * 8-bit resolution x 8 channels (PD780021AY, 780022AY, 780023AY, 780024AY) * 10-bit resolution x 8 channels (PD780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY) * Low-voltage operation: AVDD = 1.8 to 5.5 V Serial interface * 3-wire serial I/O mode: * UART mode: * I2C bus mode: 1 channel 1 channel 1 channel Timer * * * * 1 2 1 1 Timer output Three outputs (8-bit PWM output enable: 2) Clock output * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (8.38 MHz with main system clock) * 32.768 kHz (32.768 kHz with subsystem clock) Buzzer output 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (8.38 MHz with main system clock) Vectored interrupt source 16-bit operation Multiply/divide (8 bits x 8 bits, 16 bits / 8 bits) Bit manipulate (set, reset, test, and Boolean operation) BCD adjust, etc. 16-bit timer/event counter: 8-bit timer/event counter: Watch timer: Watchdog timer: Maskable Internal: 13, External: 5 Non-maskable Internal: 1 Software 1 Power supply voltage VDD = 1.8 to 5.5 V Operating ambient temperature TA = -40 to +85C Package * * * * * * 64-pin 64-pin 64-pin 64-pin 64-pin 73-pin plastic plastic plastic plastic plastic plastic 51 8 39 4 channel channels channel channel SDIP (19.05 mm (750)) QFP (14 x 14) LQFP (14 x 14) TQFP (12 x 12) LQFP (10 x 10) FBGA (9 x 9) (standard grade product only) Note The capacities of internal flash memory and internal high-speed RAM can be changed by means of the memory size switching register (IMS). User's Manual U14046EJ5V0UD 71 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) The outline of the timer/event counter is as follows (for details, see CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0, CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51, CHAPTER 10 WATCH TIMER, and CHAPTER 11 WATCHDOG TIMER). 16-Bit Timer/ Event Counter 0 8-Bit Timer/ Event Counters 50, 51 Watch Timer Watchdog Timer 1 channel 2 channels 1 channelNote 1 1 channelNote 2 Operation Interval timer Mode External event counter - - Function Timer output - - PPG output - - - PWM output - - - Pulse width measurement - - - Square-wave output - - Interrupt request Notes 1. The watch timer can perform both watch timer and interval timer functions at the same time. 2. The watchdog timer can perform either the watchdog timer function or the interval timer function. 2.9 Correspondence Between Mask ROM Versions and Flash Memory Versions Table 2-1. Correspondence Between Mask ROM Versions and Flash Memory Versions Mask ROM Version PD780021AY/2AY/3AY/4AY PD780031AY/2AY/3AY/4AY PD780021AY(A)/2AY(A)/3AY(A)/4AY(A) PD780031AY(A)/2AY(A)/3AY(A)/4AY(A) Flash Memory Version PD78F0034AY - PD78F0034BY - PD78F0034BY(A) - Remarks 1. : Supported, -: Not supported 2. The PD780034AY and PD78F0034BY, 78F0034BY(A) differ in the communication mode of flash memory programming. See 23.1 Differences Between PD78F0034A, 78F0034AY and PD78F0034B, 78F0034BY. 3. Expanded-specification products of the PD780024AY and 780034AY Subseries are not available. Only conventional products are available. 4. A special grade product of the PD78F0034AY is not available. Only a standard grade product is available. 72 User's Manual U14046EJ5V0UD CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.10 Differences Between Standard Grade Products and Special Grade Products The differences between standard grade products (PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY) and special grade products (PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A), 780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A), 78F0034BY(A)) are shown in Table 2-2. Table 2-2. Differences Between Standard Grade Products and Special Grade Products PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY, 78F0034AY, 78F0034BY PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A), 780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A), 78F0034BY(A) Quality grade Standard Special Package See 2.11 Correspondence Between Products and Packages Other (functions, electrical specifications, etc.) Same 2.11 Correspondence Between Products and Packages The following table shows the correspondence between the products and packages. Table 2-3. Correspondence Between Products and Packages Mask ROM Version PD780021AY/2AY/3AY/4AY PD780031AY/2AY/3AY/4AY Flash Memory Version PD78F0034AY PD78F0034BY Standard Special Standard Standard Special 64-pin SDIP (CW type) Note 1 - - 64-pin QFP (GC-AB8 type) Note 2 - - 64-pin LQFP (GC-8BS type) Note 1 64-pin TQFP (GK-9ET type) Note 1 64-pin LQFP (GB-8EU type) Note 1 73-pin FBGA (F1-CN3 type) - - - Notes 1. Under development 2. Only the PD780022AYGC(A)-AB8 is under mass production. The other models are still under development. Remarks 1. : Package available, -: Package not available 2. A special grade product of the PD78F0034AY is not available. Only a standard grade product is available. User's Manual U14046EJ5V0UD 73 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) 2.12 Mask Options The mask ROM versions (PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY) provide pull-up resistor mask options which allow users to specify whether to connect a pull-up resistor to a specific port pin when the user places an order for device production. Using the mask option when pull-up resistors are required reduces the number of components to add to the device, resulting in board space saving. The mask options provided in the PD780024AY and 780034AY Subseries are shown in Table 2-4. Table 2-4. Mask Options of Mask ROM Versions Pin Names P30, P31 74 Mask Option Pull-up resistor connection can be specified in 1-bit units. User's Manual U14046EJ5V0UD CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.1 Pin Function List (1) Port pins (1/2) Pin Name P00 I/O I/O P01 P02 P03 P10 to P17 P20 Input I/O P21 P22 P23 Function After Reset Alternate Function Port 0 4-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input INTP0 Port 1 8-bit input-only port. Input ANI0 to ANI7 Port 2 6-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input SI30 INTP1 INTP2 INTP3/ADTRG SO30 SCK30 RxD0 P24 TxD0 P25 ASCK0 P30 I/O P31 P32 P33 Port 3 7-bit I/O port Input/output mode can be specified in 1-bit units. N-ch open-drain I/O port On-chip pull-up resistor can be specified by mask option (mask ROM version only). LEDs can be driven directly. An on-chip pull-up resistor can be used by software settings. P34 P35 - Input SI31 SO31 P36 SCK31 P40 to P47 I/O Port 4 8-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Interrupt request flag (KRIF) is set to 1 by falling edge detection. Input AD0 to AD7 P50 to P57 I/O Port 5 8-bit I/O port LEDs can be driven directly. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input A8 to A15 P64 I/O Port 6 4-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input RD P65 P66 P67 User's Manual U14046EJ5V0UD WR WAIT ASTB 75 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) (1) Port pins (2/2) Pin Name P70 I/O I/O P71 P72 P73 Function Port 7 6-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. After Reset Input Alternate Function TI00/TO0 TI01 TI50/TO50 TI51/TO51 P74 PCL P75 BUZ (2) Non-port pins (1/2) Pin Name INTP0 I/O Function After Reset Input External interrupt request input with specifiable valid edges (rising edge, falling edge, both rising and falling edges) Input INTP1 Alternate Function P00 P01 INTP2 P02 INTP3 P03/ADTRG SI30 Input Serial interface serial data input Input SI31 SO30 P34 Output Serial interface serial data output Input SO31 SCK30 P20 P21 P35 I/O Serial interface serial clock input/output Input SCK31 P22 P36 RxD0 Input Asynchronous serial interface serial data input Input P23 TxD0 Output Asynchronous serial interface serial data output Input P24 ASCK0 Input Asynchronous serial interface serial clock input Input P25 TI00 Input External count clock input to 16-bit timer/event counter 0 Capture trigger input to 16-bit timer/event counter 0 capture register (CR00, CR01) Input P70/TO0 TI01 Capture trigger input to 16-bit timer/event counter 0 capture register (CR00) P71 TI50 External count clock input to 8-bit timer/event counter 50 P72/TO50 TI51 External count clock input to 8-bit timer/event counter 51 P73/TO51 TO0 Output 16-bit timer/event counter 0 output Input P70/TI00 TO50 8-bit timer/event counter 50 output (also used for 8-bit PWM output) Input P72/TI50 TO51 8-bit timer/event counter 51 output (also used for 8-bit PWM output) P73/TI51 PCL Output Clock output (for main system clock and subsystem clock trimming) Input P74 BUZ Output Buzzer output Input P75 Lower address/data bus when expanding external memory Input P40 to P47 AD0 to AD7 76 I/O User's Manual U14046EJ5V0UD CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) (2) Non-port pins (2/2) Pin Name I/O Function After Reset Alternate Function A8 to A15 Output Higher address bus when expanding external memory Input P50 to P57 RD Output Strobe signal output for read operation from external memory Input P64 WR Strobe signal output for write operation from external memory WAIT Input ASTB Output P65 Wait insertion when accessing external memory Input P66 Strobe output externally latching address information output to ports 4, 5 to access external memory Input P67 ANI0 to ANI7 Input A/D converter analog input Input P10 to P17 ADTRG Input A/D converter trigger signal input Input P03/INTP3 AVREF Input A/D converter reference voltage input Input - AVDD - A/D converter analog power supply. Connect to VDD0 or VDD1. - - AVSS - A/D converter ground potential. - - Input - - - - - - - - - Connect to VSS0 or VSS1. RESET Input System reset input X1 Input Crystal/ceramic connection for main system clock oscillation X2 - XT1 Input Crystal connection for subsystem clock oscillation XT2 - VDD0 - Positive power supply for ports - - VDD1 - Positive power supply other than ports - - VSS0 - Ground potential for ports - - VSS1 - Ground potential other than ports - - IC - Internally connected. Connect directly to VSS0 or VSS1. - - NCNote - Not internally connected. Leave open. - - VPP - High-voltage application for program write/verify. - - Note The NC pin is available only for a 73-pin plastic FBGA. User's Manual U14046EJ5V0UD 77 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.2 Description of Pin Functions 3.2.1 P00 to P03 (Port 0) These are 4-bit I/O ports. Besides serving as I/O ports, they function as an external interrupt input, and A/D converter external trigger input. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 4-bit I/O ports. P00 to P03 can be specified as input or output ports in 1-bit units with port mode register 0 (PM0). On-chip pullup resistors can be used by setting pull-up resistor option register 0 (PU0). (2) Control mode These ports function as an external interrupt request input, and A/D converter external trigger input. (a) INTP0 to INTP3 INTP0 to INTP3 are external interrupt request input pins which can specify valid edges (rising edge, falling edge, and both rising and falling edges). (b) ADTRG A/D converter external trigger input pin. Caution When P03 is used as an A/D converter external trigger input, specify the valid edge by bits 1, 2 (EGA00, EGA01) of A/D converter mode register (ADM0) and set interrupt mask flag (PMK3) to 1. 3.2.2 P10 to P17 (Port 1) These are 8-bit input-only ports. Besides serving as input ports, they function as an A/D converter analog input. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 8-bit input-only ports. (2) Control mode These ports function as A/D converter analog input pins (ANI0 to ANI7). 78 User's Manual U14046EJ5V0UD CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.2.3 P20 to P25 (Port 2) These are 6-bit I/O ports. Besides serving as I/O ports, they function as data I/O and clock I/O of serial interface SIO30 or UART0. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 6-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 2 (PM2). On-chip pull-up resistors can be used by setting pull-up resistor option register 2 (PU2). (2) Control mode These ports function as data I/O and clock I/O of serial interface SIO30 or UART0. (a) SI30 and SO30 Serial data I/O pins of serial interface SIO30. (b) SCK30 Serial clock I/O pin of serial interface SIO30. (c) RXD0 and TXD0 Serial data I/O pins of serial interface UART0. (d) ASCK0 Serial clock input pin of serial interface UART0. 3.2.4 P30 to P36 (Port 3) These are 7-bit I/O ports. Besides serving as I/O ports, they function as data I/O and clock I/O of serial interface SIO31. P30 to P33 can drive LEDs directly. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 7-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 3 (PM3). P30 to P33 are N-ch open-drain I/O port. On-chip pull-up resistor can be used by mask option (mask ROM version only). On-chip pull-up resistors of P34 to P36 can be used by setting pull-up resistor option register 3 (PU3). (2) Control mode These ports function as data I/O and clock I/O of serial interface SIO31. (a) SI31 and SO31 Serial data I/O pins of serial interface SIO31. (b) SCK31 Serial clock I/O pin of serial interface SIO31. User's Manual U14046EJ5V0UD 79 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.2.5 P40 to P47 (Port 4) These are 8-bit I/O ports. Besides serving as I/O ports, they function as an address/data bus. The interrupt request flag (KRIF) can be set to 1 by detecting a falling edge. The following operating mode can be specified in 1-bit units. Caution When using the falling edge detection interrupt (INTKR), be sure to set the memory expansion mode register (MEM) to 01H. (1) Port mode These ports function as 8-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 4 (PM4). On-chip pull-up resistors can be used by setting pull-up resistor option register 4 (PU4). (2) Control mode These ports function as lower address/data bus pins (AD0 to AD7) in external memory expansion mode. 3.2.6 P50 to P57 (Port 5) These are 8-bit I/O ports. Besides serving as I/O ports, they function as an address bus. Port 5 can drive LEDs directly. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 8-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 5 (PM5). On-chip pull-up resistors can be used by setting pull-up resistor option register 5 (PU5). (2) Control mode These ports function as higher address bus pins (A8 to A15) in external memory expansion mode. 3.2.7 P64 to P67 (Port 6) These are 4-bit I/O ports. Besides serving as I/O ports, they are used for control in external memory expansion mode. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 4-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 6 (PM6). On-chip pull-up resistors can be used by setting pull-up resistor option register 6 (PU6). (2) Control mode These ports function as control signal output pins (RD, WR, WAIT, ASTB) in external memory expansion mode. Caution When external wait is not used in external memory expansion mode, P66 can be used as an I/O port. 80 User's Manual U14046EJ5V0UD CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.2.8 P70 to P75 (Port 7) These are 6-bit I/O ports. Besides serving as I/O ports, they function as a timer I/O, clock output, and buzzer output. The following operating modes can be specified in 1-bit units. (1) Port mode Port 7 functions as a 6-bit I/O port. They can be specified as an input port or output port in 1-bit units with port mode register 7 (PM7). On-chip pull-up resistors can be used by setting pull-up resistor option register 7 (PU7). P70 and P71 are also 16-bit timer/event counter 0 capture trigger signal input pins with a valid edge input. (2) Control mode Port 7 functions as timer I/O, clock output, and buzzer output. (a) TI00 External count clock input pin to 16-bit timer/event counter 0 and capture trigger signal input pin to 16-bit timer/event counter capture register (CR00, CR01). (b) TI01 Capture trigger signal input pin to 16-bit timer/event counter 0 capture register (CR00). (c) TI50 and TI51 External count clock input pins to 8-bit timer/event counters 50 and 51. (d) TO0, TO50, and TO51 Timer output pins. (e) PCL Clock output pin. (f) BUZ Buzzer output pin. 3.2.9 AVREF This is an A/D converter reference voltage input pin. When no A/D converter is used, connect this pin directly to VSS0 or VSS1. 3.2.10 AVDD This is an analog power supply pin of A/D converter. Always use the same potential as that of the VDD0 pin or VDD1 pin even when no A/D converter is used. 3.2.11 AVSS This is a ground potential pin of A/D converter. Always use the same potential as that of the VSS0 pin or VSS1 pin even when no A/D converter is used. User's Manual U14046EJ5V0UD 81 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.2.12 RESET This is a low-level active system reset input pin. 3.2.13 NC NC (Non-connection) pin is not internally connected. Leave this pin open. 3.2.14 X1 and X2 Crystal/ceramic resonator connection pins for main system clock oscillation. For external clock supply, input clock signal to X1 and its inverted signal to X2. 3.2.15 XT1 and XT2 Crystal resonator connection pins for subsystem clock oscillation. For external clock supply, input the clock signal to XT1 and its inverted signal to XT2. 3.2.16 VDD0 and VDD1 VDD0 is a positive power supply port pin. VDD1 is a positive power supply pin other than port pin. 3.2.17 VSS0 and VSS1 VSS0 is a ground potential port pin. VSS1 is a ground potential pin other than port pin. 3.2.18 VPP (flash memory versions only) High-voltage apply pin for flash memory programming mode setting and program write/verify. Handle in either of the following ways. * Independently connect a 10 k pull-down resistor. * Set the jumper on the board so that this pin is connected directly to the dedicated flash programmer in programming mode and directly to VSS0 or VSS1 in normal operation mode. When there is a potential difference between the VPP pin and VSS0 pin or VSS1 pin because the wiring between the two pins is too long or external noise is input to the VPP pin, the user program may not operate normally. 3.2.19 IC (mask ROM version only) The IC (Internally Connected) pin is provided to set the test mode to check the PD780024A, 780034A Subseries at delivery. Connect it directly to the VSS0 or VSS1 pin with the shortest possible wire in the normal operating mode. When a potential difference is produced between the IC pin and VSS0 pin or VSS1 pin, because the wiring between those two pins is too long or an external noise is input to the IC pin, the user's program may not operate normally. * Connect IC pins to VSS0 pins or VSS1 pins directly. VSS0 or VSS1 IC As short as possible 82 User's Manual U14046EJ5V0UD CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) 3.3 Pin I/O Circuits and Recommended Connection of Unused Pins Table 3-1 shows the types of pin I/O circuit and the recommended connections of unused pins. See Figure 3-1 for the configuration of the I/O circuit of each type. Table 3-1. Pin I/O Circuit Types (1/2) Pin Name I/O Circuit Type I/O P00/INTP0 to P02/INTP2 8-C I/O Recommended Connection of Unused Pins Input: Independently connect to VSS0 or VSS1 via a resistor. Output: Leave open. P03/INTP3/ADTRG P10/ANI0 to P17/ANI7 25 Input P20/SI30 8-C I/O P21/SO30 5-H Connect directly to VDD0, VDD1, VSS0, or VSS1. Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. Output: Leave open. P22/SCK30 8-C P23/RxD0 P24/TxD0 5-H P25/ASCK0 8-C P30, P31 (for mask ROM version) 13-Q P30, P31 (for flash memory version) 13-P P32, P33 (for mask ROM version) 13-S P32, P33 (for flash memory version) 13-R P34/SI31 8-C P35/SO31 5-H P36/SCK31 8-C P40/AD0 to P47/AD7 5-H Input: Connect directly to VSS0 or VSS1. Output: Set the output latch of the port to 0, and leave these pins open at low level. Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. Output: Leave open. Input: Independently connect to VDD0 or VDD1 via a resistor. Output: Leave open. User's Manual U14046EJ5V0UD 83 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) Table 3-1. Pin I/O Circuit Types (2/2) Pin Name P50/A8 to P57/A15 I/O Circuit Type I/O 5-H I/O Recommended Connection of Unused Pins Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. P64/RD Output: Leave open. P65/WR P66/WAIT P67/ASTB P70/TI00/TO0 8-C P71/TI01 P72/TI50/TO50 P73/TI51/TO51 P74/PCL 5-H P75/BUZ RESET 2 Input NCNote - - XT1 16 Input - XT2 AVDD - - Leave open. Connect directly to VDD0 or VDD1. Leave open. Connect directly to VDD0 or VDD1. AVREF Connect directly to VSS0 or VSS1. AVSS IC (for mask ROM version) VPP (for flash memory version) Independently connect a 10 k pull-down resistor to this pin, or connect directly to VSS0 or VSS1. Note The NC pin is available only for a 73-pin plastic FBGA. 84 User's Manual U14046EJ5V0UD PIN FUNCTION (PD780024A, 780034A SUBSERIES) CHAPTER 3 Figure 3-1. Pin I/O Circuit List (1/2) Type 2 Type 13-P IN/OUT Data Output disable N-ch VSS0 IN Schmitt-triggered input with hysteresis characteristics Type 5-H Input enable Type 13-Q VDD0 VDD0 Mask option Pullup enable Data IN/OUT P-ch Data Output disable VDD0 P-ch N-ch VSS0 IN/OUT Output disable N-ch VSS0 Input enable Input enable Type 13-R Type 8-C VDD0 IN/OUT Pullup enable Data P-ch Data Output disable VDD0 P-ch N-ch VSS0 IN/OUT Output disable N-ch VSS0 User's Manual U14046EJ5V0UD 85 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) Figure 3-1. Pin I/O Circuit List (2/2) Type 13-S Type 25 VDD0 Mask option Data Output disable N-ch IN/OUT P-ch Comparator + -- N-ch VSS0 VREF (threshold voltage) VSS0 Input enable Type 16 Feedback cut-off P-ch XT1 86 XT2 User's Manual U14046EJ5V0UD IN CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.1 Pin Function List (1) Port pins (1/2) Pin Name P00 I/O I/O P01 P02 P03 P10 to P17 P20 Input I/O P21 P22 P23 Function After Reset Alternate Function Port 0 4-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input INTP0 Port 1 8-bit input-only port. Input ANI0 to ANI7 Port 2 6-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input SI30 INTP1 INTP2 INTP3/ADTRG SO30 SCK30 RxD0 P24 TxD0 P25 ASCK0 P30 I/O P31 P32 P33 P34 P35 Port 3 7-bit I/O port Input/output mode can be specified in 1-bit units. N-ch open-drain I/O port On-chip pull-up resistor can be specified by mask option (P30 and P31 are mask ROM version only). LEDs can be driven directly. - Input SDA0 SCL0 - An on-chip pull-up resistor can be used by software settings. P36 P40 to P47 I/O Port 4 8-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Interrupt request flag (KRIF) is set to 1 by falling edge detection. Input AD0 to AD7 P50 to P57 I/O Port 5 8-bit I/O port LEDs can be driven directly. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input A8 to A15 P64 I/O Port 6 4-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Input RD P65 P66 P67 User's Manual U14046EJ5V0UD WR WAIT ASTB 87 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) (1) Port pins (2/2) Pin Name P70 I/O I/O P71 P72 P73 Function Port 7 6-bit I/O port Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. After Reset Input Alternate Function TI00/TO0 TI01 TI50/TO50 TI51/TO51 P74 PCL P75 BUZ (2) Non-port pins (1/2) Pin Name INTP0 I/O Function After Reset Input External interrupt request input with specifiable valid edges (rising edge, falling edge, both rising and falling edges) Input INTP1 Alternate Function P00 P01 INTP2 P02 INTP3 P03/ADTRG SI30 Input Serial interface serial data input Input P20 SO30 Output Serial interface serial data output Input P21 SDA0 I/O Serial interface serial data input/output Input P32 SCK30 I/O Serial interface serial clock input/output Input P22 SCL0 P33 RxD0 Input Asynchronous serial interface serial data input Input P23 TxD0 Output Asynchronous serial interface serial data output Input P24 ASCK0 Input Asynchronous serial interface serial clock input Input P25 TI00 Input External count clock input to 16-bit timer/event counter 0 Capture trigger input to 16-bit timer/event counter 0 capture register (CR00, CR01) Input P70/TO0 TI01 Capture trigger input to 16-bit timer/event counter 0 capture register (CR00) P71 TI50 External count clock input to 8-bit timer/event counter 50 P72/TO50 TI51 External count clock input to 8-bit timer/event counter 51 P73/TO51 TO0 Output 16-bit timer/event counter 0 output Input P70/TI00 TO50 8-bit timer/event counter 50 output (also used for 8-bit PWM output) Input P72/TI50 TO51 8-bit timer/event counter 51 output (also used for 8-bit PWM output) P73/TI51 PCL Output Clock output (for main system clock and subsystem clock trimming) Input P74 BUZ Output Buzzer output Input P75 Lower address/data bus when expanding external memory Input P40 to P47 AD0 to AD7 I/O A8 to A15 Output Higher address bus when expanding external memory Input P50 to P57 RD Output Strobe signal output for read operation from external memory Input P64 WR 88 Strobe signal output for write operation from external memory User's Manual U14046EJ5V0UD P65 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) (2) Non-port pins (2/2) Pin Name I/O WAIT Input ASTB Output Function After Reset Alternate Function Wait insertion when accessing external memory Input P66 Strobe output externally latching address information output to ports 4, 5 to access external memory Input P67 ANI0 to ANI7 Input A/D converter analog input Input P10 to P17 ADTRG Input A/D converter trigger signal input Input P03/INTP3 AVREF Input A/D converter reference voltage input Input - AVDD - A/D converter analog power supply. Connect to VDD0 or VDD1. - - AVSS - A/D converter ground potential. Connect to VSS0 or VSS1. - - Input - - - - - - - - - RESET Input System reset input X1 Input Crystal connection for main system clock oscillation X2 - XT1 Input Crystal connection for subsystem clock oscillation XT2 - VDD0 - Positive power supply for ports - - VDD1 - Positive power supply other than ports - - VSS0 - Ground potential for ports - - VSS1 - Ground potential other than ports - - IC - Internally connected. Connect directly to VSS0 or VSS1. - - NCNote - Not internally connected. Leave open. - - VPP - High-voltage application for program write/verify. - - Note The NC pin is available only for a 73-pin plastic FBGA. User's Manual U14046EJ5V0UD 89 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.2 Description of Pin Functions 4.2.1 P00 to P03 (Port 0) These are 4-bit I/O ports. Besides serving as I/O ports, they function as an external interrupt input, and A/D converter external trigger input. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 4-bit I/O ports. P00 to P03 can be specified as input or output ports in 1-bit units with port mode register 0 (PM0). On-chip pullup resistors can be used by setting pull-up resistor option register 0 (PU0). (2) Control mode These ports function as an external interrupt request input, and A/D converter external trigger input. (a) INTP0 to INTP3 INTP0 to INTP3 are external interrupt request input pins which can specify valid edges (rising edge, falling edge, and both rising and falling edges). (b) ADTRG A/D converter external trigger input pin. Caution When P03 is used as an A/D converter external trigger input, specify the valid edge by bits 1, 2 (EGA00, EGA01) of A/D converter mode register (ADM0) and set interrupt mask flag (PMK3) to 1. 4.2.2 P10 to P17 (Port 1) These are 8-bit input-only ports. Besides serving as input ports, they function as an A/D converter analog input. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 8-bit input-only ports. (2) Control mode These ports function as A/D converter analog input pins (ANI0 to ANI7). 90 User's Manual U14046EJ5V0UD CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.2.3 P20 to P25 (Port 2) These are 6-bit I/O ports. Besides serving as I/O ports, they function as serial interface data I/O and clock I/O. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 6-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 2 (PM2). On-chip pull-up resistors can be used by setting pull-up resistor option register 2 (PU2). (2) Control mode These ports function as data I/O and clock I/O of serial interface SIO30 or UART0. (a) SI30 and SO30 Serial data I/O pins of serial interface SIO30. (b) SCK30 Serial clock I/O pin of serial interface SIO30. (c) RXD0 and TXD0 Serial data I/O pins of serial interface UART0. (d) ASCK0 Serial clock input pin of serial interface UART0. 4.2.4 P30 to P36 (Port 3) These are 7-bit I/O ports. Besides serving as I/O ports, they function as data I/O and clock I/O of serial interface IIC0. P30 to P33 can drive LEDs directly. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 7-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 3 (PM3). P30 to P33 are N-ch open-drain I/O port. Mask ROM version can contain pull-up resistors in P30 and P31 with the mask option. On-chip pull-up resistors of P34 to P36 can be used by setting pull-up resistor option register 3 (PU3). (2) Control mode These ports function as data I/O and clock I/O of serial interface IIC0. (a) SDA0 Serial data I/O pin of serial interface IIC0. (b) SCL0 Serial clock I/O pin of serial interface IIC0. User's Manual U14046EJ5V0UD 91 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.2.5 P40 to P47 (Port 4) These are 8-bit I/O ports. Besides serving as I/O ports, they function as an address/data bus. The interrupt request flag (KRIF) can be set to 1 by detecting a falling edge. The following operating mode can be specified in 1-bit units. Caution When using the falling edge detection interrupt (INTKR), be sure to set the memory expansion mode register (MEM) to 01H. (1) Port mode These ports function as 8-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 4 (PM4). On-chip pull-up resistors can be used by setting pull-up resistor option register 4 (PU4). (2) Control mode These ports function as lower address/data bus pins (AD0 to AD7) in external memory expansion mode. 4.2.6 P50 to P57 (Port 5) These are 8-bit I/O ports. Besides serving as I/O ports, they function as an address bus. Port 5 can drive LEDs directly. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 8-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 5 (PM5). On-chip pull-up resistors can be used by setting pull-up resistor option register 5 (PU5). (2) Control mode These ports function as higher address bus pins (A8 to A15) in external memory expansion mode. 4.2.7 P64 to P67 (Port 6) These are 4-bit I/O ports. Besides serving as I/O ports, they are used for control in external memory expansion mode. The following operating modes can be specified in 1-bit units. (1) Port mode These ports function as 4-bit I/O ports. They can be specified as input or output ports in 1-bit units with port mode register 6 (PM6). On-chip pull-up resistors can be used by setting pull-up resistor option register 6 (PU6). (2) Control mode These ports function as control signal output pins (RD, WR, WAIT, ASTB) in external memory expansion mode. Caution When external wait is not used in external memory expansion mode, P66 can be used as an I/O port. 92 User's Manual U14046EJ5V0UD CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.2.8 P70 to P75 (Port 7) These are 6-bit I/O ports. Besides serving as I/O ports, they function as a timer I/O, clock output, and buzzer output. The following operating modes can be specified in 1-bit units. (1) Port mode Port 7 functions as a 6-bit I/O port. They can be specified as an input port or output port in 1-bit units with port mode register 7 (PM7). On-chip pull-up resistors can be used by setting pull-up resistor option register 7 (PU7). P70 and P71 are also 16-bit timer/event counter 0 capture trigger signal input pins with a valid edge input. (2) Control mode Port 7 functions as timer I/O, clock output, and buzzer output. (a) TI00 External count clock input pin to 16-bit timer/event counter 0 and capture trigger signal input pin to 16-bit timer/event counter capture register (CR00, CR01). (b) TI01 Capture trigger signal input pin to 16-bit timer/event counter 0 capture register (CR00). (c) TI50 and TI51 External count clock input pins to 8-bit timer/event counters 50 and 51. (d) TO0, TO50, and TO51 Timer output pins. (e) PCL Clock output pin. (f) BUZ Buzzer output pin. 4.2.9 AVREF This is an A/D converter reference voltage input pin. When no A/D converter is used, connect this pin directly to VSS0 or VSS1. 4.2.10 AVDD This is an analog power supply pin of A/D converter. Always use the same potential as that of the VDD0 pin or VDD1 pin even when no A/D converter is used. 4.2.11 AVSS This is a ground potential pin of A/D converter. Always use the same potential as that of the VSS0 pin or VSS1 pin even when no A/D converter is used. User's Manual U14046EJ5V0UD 93 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.2.12 RESET This is a low-level active system reset input pin. 4.2.13 NC NC (Non-connection) pin is not internally connected. Leave this pin open. 4.2.14 X1 and X2 Crystal/ceramic resonator connection pins for main system clock oscillation. For external clock supply, input the clock signal to X1 and its inverted signal to X2. 4.2.15 XT1 and XT2 Crystal resonator connection pins for subsystem clock oscillation. For external clock supply, input the clock signal to XT1 and its inverted signal to XT2. 4.2.16 VDD0 and VDD1 VDD0 is a positive power supply pin. VDD1 is a positive power supply pin other than port pin. 4.2.17 VSS0 and VSS1 VSS0 is a ground potential port pin. VSS1 is a ground potential pin other than port pin. 4.2.18 VPP (flash memory versions only) High-voltage apply pin for flash memory programming mode setting and program write/verify. Handle in either of the following ways. * Independently connect a 10 k pull-down resistor. * Set the jumper on the board so that this pin is connected directly to the dedicated flash programmer in programming mode and directly to VSS0 or VSS1 in normal operation mode. When there is a potential difference between the VPP pin and VSS0 pin or VSS1 pin because the wiring between the two pins is too long or external noise is input to the VPP pin, the user program may not operate normally. 4.2.19 IC (mask ROM version only) The IC (Internally Connected) pin is provided to set the test mode to check the PD780024AY, 780034AY Subseries at delivery. Connect it directly to the VSS0 or VSS1 pin with the shortest possible wire in the normal operating mode. When a potential difference is produced between the IC pin and VSS0 pin or VSS1 pin, because the wiring between those two pins is too long or an external noise is input to the IC pin, the user's program may not operate normally. * Connect IC pins to VSS0 pins or VSS1 pins directly. VSS0 or VSS1 IC As short as possible 94 User's Manual U14046EJ5V0UD CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) 4.3 Pin I/O Circuits and Recommended Connection of Unused Pins Table 4-1 shows the types of pin I/O circuit and the recommended connections of unused pins. See Figure 4-1 for the configuration of the I/O circuit of each type. Table 4-1. Pin I/O Circuit Types (1/2) Pin Name I/O Circuit Type I/O P00/INTP0 to P02/INTP2 8-C I/O Recommended Connection of Unused Pins Input: Independently connect to VSS0 or VSS1 via a resistor. Output: Leave open. P03/INTP3/ADTRG P10/ANI0 to P17/ANI7 25 Input P20/SI30 8-C I/O P21/SO30 5-H Connect directly to VDD0, VDD1, VSS0, or VSS1. Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. Output: Leave open. P22/SCK30 8-C P23/RxD0 P24/TxD0 5-H P25/ASCK0 8-C P30, P31 (for mask ROM version) 13-Q P30, P31 (for flash memory version) 13-P P32/SDA0 13-R Input: Connect directly to VSS0 or VSS1. Output: Set the output latch of the port to 0, and leave these pins open at low level. P33/SCL0 P34 8-C P35 5-H P36 8-C P40/AD0 to P47/AD7 5-H Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. Output: Leave open. Input: Independently connect to VDD0 or VDD1 via a resistor. Output: Leave open. User's Manual U14046EJ5V0UD 95 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) Table 4-1. Pin I/O Circuit Types (2/2) Pin Name P50/A8 to P57/A15 I/O Circuit Type I/O 5-H I/O Recommended Connection of Unused Pins Input: Independently connect to VDD0, VDD1, VSS0, or VSS1 via a resistor. P64/RD Output: Leave open. P65/WR P66/WAIT P67/ASTB P70/TI00/TO0 8-C P71/TI01 P72/TI50/TO50 P73/TI51/TO51 P74/PCL 5-H P75/BUZ RESET 2 Input NCNote - - XT1 16 Input - XT2 AVDD - - Leave open. Connect directly to VDD0 or VDD1. Leave open. Connect directly to VDD0 or VDD1. AVREF Connect directly to VSS0 or VSS1. AVSS IC (for mask ROM version) VPP (for flash memory version) Independently connect a 10 k pull-down resistor to this pin, or connect directly to VSS0 or VSS1. Note The NC pin is available only for a 73-pin plastic FBGA. 96 User's Manual U14046EJ5V0UD PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) CHAPTER 4 Figure 4-1. Pin I/O Circuit List (1/2) Type 2 Type 13-P IN/OUT Data Output disable N-ch VSS0 IN Schmitt-triggered input with hysteresis characteristics Type 5-H Input enable Type 13-Q VDD0 VDD0 Mask option Pullup enable Data IN/OUT P-ch Data Output disable VDD0 P-ch N-ch VSS0 IN/OUT Output disable N-ch VSS0 Input enable Input enable Type 13-R Type 8-C VDD0 IN/OUT Pullup enable Data P-ch Data Output disable VDD0 P-ch N-ch VSS0 IN/OUT Output disable N-ch VSS0 User's Manual U14046EJ5V0UD 97 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) Figure 4-1. Pin I/O Circuit List (2/2) Type 16 Type 25 Feedback cut-off P-ch Comparator P-ch + -- N-ch VSS0 VREF (threshold voltage) Input enable XT1 98 XT2 User's Manual U14046EJ5V0UD IN CHAPTER 5 CPU ARCHITECTURE 5.1 Memory Spaces PD780024A, 780034A, 780024AY, 780034AY Subseries can access 64 KB memory space respectively. Figures 5-1 to 5-5 show memory maps. Caution In case of the internal memory capacity, the initial value of memory size switching register (IMS) of all products (PD780024A, 780034A, 780024AY, and 780034AY Subseries) is fixed (IMS = CFH). Therefore, set the value corresponding to each product indicated below in the initial setting. PD780021A, 780031A, 780021AY, 780031AY: 42H PD780022A, 780032A, 780022AY, 780032AY: 44H PD780023A, 780033A, 780023AY, 780033AY: C6H PD780024A, 780034A, 780024AY, 780034AY: C8H PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY: Value for mask ROM version Figure 5-1. Memory Map (PD780021A, 780031A, 780021AY, 780031AY) FFFFH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits Internal high-speed RAM 512 x 8 bits FD00H FCFFH 1FFFH Reserved Data memory space Program area 1000H 0FFFH F800H F7FFH CALLF entry area External memory 55296 x 8 bits 0800H 07FFH Program area Program memory space 0080H 007FH 2000H 1FFFH CALLT table area Internal ROM 8192 x 8 bits 0040H 003FH Vector table area 0000H 0000H User's Manual U14046EJ5V0UD 99 CHAPTER 5 CPU ARCHITECTURE Figure 5-2. Memory Map (PD780022A, 780032A, 780022AY, 780032AY) FFFFH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits Internal high-speed RAM 512 x 8 bits FD00H FCFFH 3FFFH Reserved Data memory space Program area 1000H 0FFFH F800H F7FFH CALLF entry area External memory 47104 x 8 bits 0800H 07FFH Program area Program memory space 0080H 007FH 4000H 3FFFH CALLT table area Internal ROM 16384 x 8 bits 0040H 003FH Vector table area 0000H 0000H 100 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE Figure 5-3. Memory Map (PD780023A, 780033A, 780023AY, 780033AY) FFFFH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits Internal high-speed RAM 1024 x 8 bits FB00H FAFFH 5FFFH Reserved Data memory space Program area 1000H 0FFFH F800H F7FFH CALLF entry area External memory 38912 x 8 bits 0800H 07FFH Program area Program memory space 0080H 007FH 6000H 5FFFH CALLT table area Internal ROM 24576 x 8 bits 0040H 003FH Vector table area 0000H 0000H User's Manual U14046EJ5V0UD 101 CHAPTER 5 CPU ARCHITECTURE Figure 5-4. Memory Map (PD780024A, 780034A, 780024AY, 780034AY) FFFFH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits Internal high-speed RAM 1024 x 8 bits FB00H FAFFH 7FFFH Reserved Data memory space Program area 1000H 0FFFH F800H F7FFH CALLF entry area External memory 30720 x 8 bits 0800H 07FFH Program area Program memory space 0080H 007FH 8000H 7FFFH CALLT table area Internal ROM 32768 x 8 bits 0040H 003FH Vector table area 0000H 102 0000H User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE Figure 5-5. Memory Map (PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY) FFFFH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits Internal high-speed RAM 1024 x 8 bits FB00H FAFFH 7FFFH Reserved Data memory space Program area 1000H 0FFFH F800H F7FFH CALLF entry area External memory 30720 x 8 bits 0800H 07FFH Program area Program memory space 0080H 007FH 8000H 7FFFH CALLT table area Flash memory 32768 x 8 bits 0040H 003FH Vector table area 0000H 0000H User's Manual U14046EJ5V0UD 103 CHAPTER 5 CPU ARCHITECTURE 5.1.1 Internal program memory space The internal program memory space contains the program and table data. Normally, it is addressed with the program counter (PC). The PD780024A, 780034A, 780024AY, and 780034AY Subseries products incorporate an on-chip ROM (mask ROM or flash memory), as listed below. Table 5-1. Internal ROM Capacity Part Number Type PD780021A, 780031A, 780021AY, 780031AY Mask ROM Capacity 8192 x 8 bits (0000H to 1FFFH) PD780022A, 780032A, 780022AY, 780032AY 16384 x 8 bits (0000H to 3FFFH) PD780023A, 780033A, 780023AY, 780033AY 24576 x 8 bits (0000H to 5FFFH) PD780024A, 780034A, 780024AY, 780034AY 32768 x 8 bits (0000H to 7FFFH) PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Flash memory 32768 x 8 bits (0000H to 7FFFH) The internal program memory space is divided into the following three areas. 104 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE (1) Vector table area The 64-byte area 0000H to 003FH is reserved as a vector table area. The RESET input and program start addresses for branch upon generation of each interrupt request are stored in the vector table area. Of the 16bit address, lower 8 bits are stored at even addresses and higher 8 bits are stored at odd addresses. Table 5-2. Vector Table Vector Table Address Interrupt Source 0000H RESET input 0004H INTWDT 0006H INTP0 0008H INTP1 000AH INTP2 000CH INTP3 000EH INTSER0 0010H INTSR0 0012H INTST0 0014H INTCSI30 0016H INTCSI31Note 1 0018H INTIIC0Note 2 001AH INTWTI 001CH INTTM00 001EH INTTM01 0020H INTTM50 0022H INTTM51 0024H INTAD0 0026H INTWT 0028H INTKR 003EH BRK Notes 1. PD780024A, 780034A Subseries only 2. PD780024AY, 780034AY Subseries only (2) CALLT instruction table area The 64-byte area 0040H to 007FH can store the subroutine entry address of a 1-byte call instruction (CALLT). (3) CALLF instruction entry area The area 0800H to 0FFFH can perform a direct subroutine call with a 2-byte call instruction (CALLF). User's Manual U14046EJ5V0UD 105 CHAPTER 5 CPU ARCHITECTURE 5.1.2 Internal data memory space The PD780024A, 780034A, 780024AY, and 780034AY Subseries products incorporate an internal high-speed RAM, as listed below. Table 5-3. Internal High-Speed RAM Capacity Part Number Internal High-Speed RAM PD780021A, 780031A, 780021AY, 780031AY 512 x 8 bits (FD00H to FEFFH) PD780022A, 780032A, 780022AY, 780032AY PD780023A, 780033A, 780023AY, 780033AY 1024 x 8 bits (FB00H to FEFFH) PD780024A, 780034A, 780024AY, 780034AY PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY The 32-byte area FEE0H to FEFFH is allocated four general-purpose register banks composed of eight 8-bit registers. This area cannot be used as a program area in which instructions are written and executed. The internal high-speed RAM can also be used as a stack memory. 5.1.3 Special function register (SFR) area An on-chip peripheral hardware special function register (SFR) is allocated in the area FF00H to FFFFH (see 5.2.3 Special function register (SFR) Table 5-5 Special Function Register List). Caution Do not access addresses where the SFR is not assigned. 5.1.4 External memory space The external memory space is accessible with memory expansion mode register (MEM). External memory space can store program, table data, etc., and allocate peripheral devices. 106 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE 5.1.5 Data memory addressing Addressing refers to the method of specifying the address of the instruction to be executed next or the address of the register or memory relevant to the execution of instructions. Several addressing modes are provided for addressing the memory relevant to the execution of instructions for the PD780024A, 780034A, 780024AY, and 780034AY Subseries, based on operability and other considerations. For areas containing data memory in particular, special addressing methods designed for the functions of special function registers (SFR) and general-purpose registers are available for use. Correspondence between data memory and addressing is illustrated in Figures 5-6 to 5-10. For the details of each addressing mode, see 5.4 Operand Address Addressing. Figure 5-6. Correspondence Between Data Memory and Addressing (PD780021A, 780031A, 780021AY, 780031AY) FFFFH FF20H FF1FH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits SFR addressing Register addressing Short direct addressing Internal high-speed RAM 512 x 8 bits FE20H FE1FH FD00H FCFFH Direct addressing Reserved Register indirect addressing Based addressing F800H F7FFH Based indexed addressing External memory 55296 x 8 bits 2000H 1FFFH Internal ROM 8192 x 8 bits 0000H User's Manual U14046EJ5V0UD 107 CHAPTER 5 CPU ARCHITECTURE Figure 5-7. Correspondence Between Data Memory and Addressing (PD780022A, 780032A, 780022AY, 780032AY) FFFFH FF20H FF1FH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits SFR addressing Register addressing Short direct addressing Internal high-speed RAM 512 x 8 bits FE20H FE1FH FD00H FCFFH Direct addressing Reserved Register indirect addressing Based addressing F800H F7FFH Based indexed addressing External memory 47104 x 8 bits 4000H 3FFFH Internal ROM 16384 x 8 bits 0000H 108 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE Figure 5-8. Correspondence Between Data Memory and Addressing (PD780023A, 780033A, 780023AY, 780033AY) FFFFH FF20H FF1FH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits SFR addressing Register addressing Short direct addressing Internal high-speed RAM 1024 x 8 bits FE20H FE1FH FB00H FAFFH Direct addressing Reserved Register indirect addressing Based addressing F800H F7FFH Based indexed addressing External memory 38912 x 8 bits 6000H 5FFFH Internal ROM 24576 x 8 bits 0000H User's Manual U14046EJ5V0UD 109 CHAPTER 5 CPU ARCHITECTURE Figure 5-9. Correspondence Between Data Memory and Addressing (PD780024A, 780034A, 780024AY, 780034AY) FFFFH FF20H FF1FH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits SFR addressing Register addressing Short direct addressing Internal high-speed RAM 1024 x 8 bits FE20H FE1FH FB00H FAFFH Direct addressing Reserved Register indirect addressing Based addressing F800H F7FFH Based indexed addressing External memory 30720 x 8 bits 8000H 7FFFH Internal ROM 32768 x 8 bits 0000H 110 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE Figure 5-10. Correspondence Between Data Memory and Addressing (PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY) FFFFH FF20H FF1FH FF00H FEFFH FEE0H FEDFH Special function registers (SFRs) 256 x 8 bits General-purpose registers 32 x 8 bits SFR addressing Register addressing Short direct addressing Internal high-speed RAM 1024 x 8 bits FE20H FE1FH FB00H FAFFH Direct addressing Reserved Register indirect addressing Based addressing F800H F7FFH Based indexed addressing External memory 30720 x 8 bits 8000H 7FFFH Flash memory 32768 x 8 bits 0000H User's Manual U14046EJ5V0UD 111 CHAPTER 5 CPU ARCHITECTURE 5.2 Processor Registers The PD780024A, 780034A, 780024AY, 780034AY Subseries products incorporate the following processor registers. 5.2.1 Control registers The control registers control the program sequence, statuses and stack memory. The control registers consist of a program counter (PC), a program status word (PSW) and a stack pointer (SP). (1) Program counter (PC) The program counter is a 16-bit register which holds the address information of the next program to be executed. In normal operation, the PC is automatically incremented according to the number of bytes of the instruction to be fetched. When a branch instruction is executed, immediate data and register contents are set. RESET input sets the reset vector table values at addresses 0000H and 0001H to the program counter. Figure 5-11. Program Counter Format 15 PC 0 PC15 PC14 PC13 PC12 PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 (2) Program status word (PSW) The program status word is an 8-bit register consisting of various flags to be set/reset by instruction execution. Program status word contents are automatically stacked upon interrupt request generation or PUSH PSW instruction execution and are automatically reset upon execution of the RETB, RETI and POP PSW instructions. RESET input sets the PSW to 02H. Figure 5-12. Program Status Word Format 7 PSW 112 IE 0 Z RBS1 AC RBS0 0 User's Manual U14046EJ5V0UD ISP CY CHAPTER 5 CPU ARCHITECTURE (a) Interrupt enable flag (IE) This flag controls the interrupt request acknowledge operations of the CPU. When 0, the IE is set to the disable interrupt (DI) state, and only non-maskable interrupt request becomes acknowledgeable. Other interrupt requests are all disabled. When 1, the IE is set to the enable interrupt (EI) state and interrupt request acknowledge enable is controlled with an in-service priority flag (ISP), an interrupt mask flag for various interrupt sources and a priority specification flag. The IE is reset (0) upon DI instruction execution or interrupt acknowledgment and is set (1) upon EI instruction execution. (b) Zero flag (Z) When the operation result is zero, this flag is set (1). It is reset (0) in all other cases. (c) Register bank select flags (RBS0 and RBS1) These are 2-bit flags to select one of the four register banks. In these flags, the 2-bit information which indicates the register bank selected by SEL RBn instruction execution is stored. (d) Auxiliary carry flag (AC) If the operation result has a carry from bit 3 or a borrow at bit 3, this flag is set (1). It is reset (0) in all other cases. (e) In-service priority flag (ISP) This flag manages the priority of acknowledgeable maskable vectored interrupts. When this flag is 0, lowlevel vectored interrupt requests specified with a priority specification flag register (PR0L, PR0H, PR1L) (see 19.3 (3) Priority specification flag registers (PR0L, PR0H, PR1L)) are disabled for acknowledgment. When it is 1, all interrupts are acknowledgeable. Actual request acknowledgment is controlled with the interrupt enable flag (IE). (f) Carry flag (CY) This flag stores overflow and underflow upon add/subtract instruction execution. It stores the shift-out value upon rotate instruction execution and functions as a bit accumulator during bit manipulation instruction execution. (3) Stack pointer (SP) This is a 16-bit register to hold the start address of the memory stack area. Only the internal high-speed RAM area can be set as the stack area. The internal high-speed RAM areas of each product are as follows. Table 5-4. Internal High-Speed RAM Area Part Number Internal High-Speed RAM Area PD780021A, 780031A, 780021AY, 780031AY PD780022A, 780032A, 780022AY, 780032AY FD00H to FEFFH PD780023A, 780033A, 780023AY, 780033AY PD780024A, 780034A, 780024AY, 780034AY PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY FB00H to FEFFH User's Manual U14046EJ5V0UD 113 CHAPTER 5 CPU ARCHITECTURE Figure 5-13. Stack Pointer Format 15 SP 0 SP15 SP14 SP13 SP12 SP11 SP10 SP9 SP8 SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 The SP is decremented ahead of write (save) to the stack memory and is incremented after read (restore) from the stack memory. Each stack operation saves/restores data as shown in Figures 5-14 and 5-15. Caution Since RESET input makes the SP contents undefined, be sure to initialize the SP before using the stack. Figure 5-14. Data to Be Saved to Stack Memory (a) PUSH rp instruction (when SP is FEE0H) SP SP FEE0H FEDEH FEE0H FEDFH Register pair higher FEDEH Register pair lower (b) CALL, CALLF, CALLT instructions (when SP is FEE0H) SP SP FEE0H FEDEH FEE0H FEDFH PC15 to PC8 FEDEH PC7 to PC0 (c) Interrupt, BRK instruction (when SP is FEE0H) SP SP 114 FEE0H FEDDH FEE0H FEDFH PSW FEDEH PC15 to PC8 FEDDH PC7 to PC0 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE Figure 5-15. Data to Be Restored from Stack Memory (a) POP rp instruction (when SP is FEDEH) SP SP FEE0H FEDEH FEE0H FEDFH Register pair higher FEDEH Register pair lower (b) RET instruction (when SP is FEDEH) SP SP FEE0H FEDEH FEE0H FEDFH PC15 to PC8 FEDEH PC7 to PC0 (c) RETI, RETB instructions (when SP is FEDDH) SP SP FEE0H FEDDH FEE0H FEDFH PSW FEDEH PC15 to PC8 FEDDH PC7 to PC0 User's Manual U14046EJ5V0UD 115 CHAPTER 5 CPU ARCHITECTURE 5.2.2 General-purpose registers A general-purpose register is mapped at particular addresses (FEE0H to FEFFH) of the data memory. It consists of 4 banks, each bank consisting of eight 8-bit registers (X, A, C, B, E, D, L, and H). Each register can also be used as an 8-bit register. Two 8-bit registers can be used in pairs as a 16-bit register (AX, BC, DE, and HL). They can be described in terms of function names (X, A, C, B, E, D, L, H, AX, BC, DE, and HL) and absolute names (R0 to R7 and RP0 to RP3). Register banks to be used for instruction execution are set with the CPU control instruction (SEL RBn). Because of the 4-register bank configuration, an efficient program can be created by switching between a register for normal processing and a register for interrupts for each bank. Figure 5-16. General-Purpose Register Configuration (a) Absolute name 16-bit processing 8-bit processing FEFFH R7 BANK0 RP3 R6 FEF8H R5 BANK1 RP2 R4 FEF0H R3 RP1 BANK2 R2 FEE8H R1 RP0 BANK3 R0 FEE0H 15 0 7 0 (b) Function name 16-bit processing 8-bit processing FEFFH H BANK0 HL L FEF8H D BANK1 DE E FEF0H B BC BANK2 C FEE8H A AX BANK3 X FEE0H 15 116 User's Manual U14046EJ5V0UD 0 7 0 CHAPTER 5 CPU ARCHITECTURE 5.2.3 Special function register (SFR) Unlike a general-purpose register, each special function register has special functions. It is allocated in the FF00H to FFFFH area. The special function register can be manipulated like the general-purpose register, with the operation, transfer and bit manipulation instructions. Manipulatable bit units, 1, 8, and 16, depend on the special function register type. Each manipulation bit unit can be specified as follows. * 1-bit manipulation Describe the symbol reserved with assembler for the 1-bit manipulation instruction operand (sfr.bit). This manipulation can also be specified with an address. * 8-bit manipulation Describe the symbol reserved with assembler for the 8-bit manipulation instruction operand (sfr). This manipulation can also be specified with an address. * 16-bit manipulation Describe the symbol reserved with assembler for the 16-bit manipulation instruction operand (sfrp). When addressing an address, describe an even address. Table 5-5 gives a list of special function registers. The meaning of items in the table is as follows. * Symbol Symbol indicating the address of a special function register. It is a reserved word in the RA78K0, and is defined as the sfr variable by the #pragma sfr direction in the CC78K0. When using the RA78K0, ID78K0-NS, ID78K0, or SM78K0, symbols can be written as an instruction operand. * R/W Indicates whether the corresponding special function register can be read or written. R/W: Read/write enable R: Read only W: Write only * Manipulatable bit units Indicates the manipulatable bit unit (1, 8, or 16). "-" indicates a bit unit for which manipulation is not possible. * After reset Indicates each register status upon RESET input. User's Manual U14046EJ5V0UD 117 CHAPTER 5 CPU ARCHITECTURE Table 5-5. Special Function Register List (1/3) Address Special Function Register (SFR) Name Symbol R/W Manipulatable Bit Unit After Reset 1 Bit 8 Bits 16 Bits FF00H Port 0 P0 R/W - FF01H Port 1 P1 R - FF02H Port 2 P2 R/W - FF03H Port 3 P3 - FF04H Port 4 P4 - FF05H Port 5 P5 - FF06H Port 6 P6 - FF07H Port 7 P7 - FF0AH 16-bit timer capture/compare register 00 CR00 - - 16-bit timer capture/compare register 01 CR01 - - 16-bit timer counter 0 TM0 R - - 0000H FF10H 8-bit timer compare register 50 CR50 R/W - - Undefined FF11H 8-bit timer compare register 51 CR51 - - FF12H 8-bit timer counter 50 TM5 - FF13H 8-bit timer counter 51 - FF16H A/D conversion result register 0 - - - Note 1 00H Undefined FF0BH FF0CH FF0DH FF0EH FF0FH TM50 R TM51 ADCR0 FF17H FF18H FF1AH FF1BH FF1FH TXS0 W - - Receive buffer register 0 RXB0 R - - Serial I/O shift register 30 SIO30 R/W - - SIO31 - - IIC0 - - Serial I/O shift register IIC shift register 0Note 4 Notes 1. PD780024A, 780024AY Subseries only 2. PD780034A, 780034AY Subseries only, 16-bit access possible 3. PD780024A, 780034A Subseries only 4. PD780024AY, 780034AY Subseries only 118 Note 2 Transmit shift register 0 31Note 3 User's Manual U14046EJ5V0UD 00H FFH Undefined 00H CHAPTER 5 CPU ARCHITECTURE Table 5-5. Special Function Register List (2/3) Address Special Function Register (SFR) Name Symbol R/W Manipulatable Bit Unit After Reset 1 Bit 8 Bits 16 Bits - PM2 - Port mode register 3 PM3 - FF24H Port mode register 4 PM4 - FF25H Port mode register 5 PM5 - FF26H Port mode register 6 PM6 - FF27H Port mode register 7 PM7 - FF30H Pull-up resistor option register 0 PU0 - FF32H Pull-up resistor option register 2 PU2 - FF33H Pull-up resistor option register 3 PU3 - FF34H Pull-up resistor option register 4 PU4 - FF35H Pull-up resistor option register 5 PU5 - FF36H Pull-up resistor option register 6 PU6 - FF37H Pull-up resistor option register 7 PU7 - FF40H Clock output select register CKS - FF41H Watch timer operation mode register WTM - FF42H Watchdog timer clock select register WDCS - - FF47H Memory expansion mode register MEM - FF48H External interrupt rising edge enable register EGP - FF49H External interrupt falling edge enable register EGN - FF60H 16-bit timer mode control register 0 TMC0 - FF61H Prescaler mode register 0 PRM0 - - FF62H Capture/compare control register 0 CRC0 - FF63H 16-bit timer output control register 0 TOC0 - FF70H 8-bit timer mode control register 50 TMC50 - FF71H Timer clock select register 50 TCL50 - - FF78H 8-bit timer mode control register 51 TMC51 - FF79H Timer clock select register 51 TCL51 - - FF80H A/D converter mode register 0 ADM0 - FF81H Analog input channel specification register 0 ADS0 - - FFA0H Asynchronous serial interface mode register 0 ASIM0 - FFA1H Asynchronous serial interface status register 0 ASIS0 R - - FFA2H Baud rate generator control register 0 BRGC0 R/W - - FF20H Port mode register 0 PM0 FF22H Port mode register 2 FF23H User's Manual U14046EJ5V0UD R/W FFH 00H 119 CHAPTER 5 CPU ARCHITECTURE Table 5-5. Special Function Register List (3/3) Address Special Function Register (SFR) Name Symbol R/W Manipulatable Bit Unit After Reset 1 Bit FFA8H FFA9H FFAAH IIC control register IIC status register 0Note 1 0Note 1 IIC transfer clock select register 0Note 1 0Note 1 FFABH Slave address register FFB0H Serial operation mode register 30 31Note 2 8 Bits 16 Bits IICC0 R/W - IICS0 R - R/W - SVA0 - - CSIM30 - CSIM31 - IF0L IF0H - MK0L MK0H - PR0L PR0H IICCL0 00H FFB8H Serial operation mode register FFE0H Interrupt request flag register 0L FFE1H Interrupt request flag register 0H FFE2H Interrupt request flag register 1L IF1L FFE4H Interrupt mask flag register 0L MK0 FFE5H Interrupt mask flag register 0H FFE6H Interrupt mask flag register 1L MK1L FFE8H Priority level specification flag register 0L PR0 FFE9H Priority level specification flag register 0H FFEAH Priority level specification flag register 1L PR1L - FFF0H Memory size switching register IMS - - CFHNote 3 FFF8H Memory expansion wait setting register MM - 10H FFF9H Watchdog timer mode register WDTM - 00H FFFAH Oscillation stabilization time select register OSTS - - 04H FFFBH Processor clock control register PCC - IF0 FFH Notes 1. PD780024AY, 780034AY Subseries only 2. PD780024A, 780034A Subseries only 3. The default is CFH, but set the value corresponding to each respective product as indicated below in the initial setting. PD780021A, 780031A, 780021AY, 780031AY: 42H PD780022A, 780032A, 780022AY, 780032AY: 44H PD780023A, 780033A, 780023AY, 780033AY: C6H PD780024A, 780034A, 780024AY, 780034AY: C8H PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY: Value for mask ROM version 120 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE 5.3 Instruction Address Addressing An instruction address is determined by program counter (PC) contents and is normally incremented (+1 for each byte) automatically according to the number of bytes of an instruction to be fetched each time another instruction is executed. When a branch instruction is executed, the branch destination information is set to the PC and branched by the following addressing (for details of instructions, refer to 78K/0 Series Instructions User's Manual (U12326E)). 5.3.1 Relative addressing [Function] The value obtained by adding 8-bit immediate data (displacement value: jdisp8) of an instruction code to the start address of the following instruction is transferred to the program counter (PC) and branched. The displacement value is treated as signed two's complement data (-128 to +127) and bit 7 becomes a sign bit. In other words, relative addressing consists in relative branching from the start address of the following instruction to the -128 to +127 range. This function is carried out when the BR $addr16 instruction or a conditional branch instruction is executed. [Illustration] 15 0 ... PC indicates the start address of the instruction after the BR instruction. PC + 15 8 7 0 6 S jdisp8 15 0 PC When S = 0, all bits of are 0. When S = 1, all bits of are 1. User's Manual U14046EJ5V0UD 121 CHAPTER 5 CPU ARCHITECTURE 5.3.2 Immediate addressing [Function] Immediate data in the instruction word is transferred to the program counter (PC) and branched. This function is carried out when the CALL !addr16 or BR !addr16 or CALLF !addr11 instruction is executed. CALL !addr16 and BR !addr16 instructions can be branched to the entire memory space. The CALLF !addr11 instruction is branched to the 0800H to 0FFFH area. [Illustration] In the case of CALL !addr16 and BR !addr16 instructions 7 0 CALL or BR Low Addr. High Addr. 15 8 7 0 PC In the case of CALLF !addr11 instruction 7 6 4 3 fa10-8 0 CALLF fa7-0 15 PC 122 0 11 10 0 0 0 8 7 1 User's Manual U14046EJ5V0UD 0 CHAPTER 5 CPU ARCHITECTURE 5.3.3 Table indirect addressing [Function] Table contents (branch destination address) of the particular location to be addressed by bits 1 to 5 of the immediate data of an operation code are transferred to the program counter (PC) and branched. This function is carried out when the CALLT [addr5] instruction is executed. This instruction references the address stored in the memory table from 40H to 7FH, and allows branching to the entire memory space. [Illustration] 7 Operation code 6 1 5 1 1 ta4-0 1 15 Effective address 0 7 0 0 0 0 0 0 Memory (Table) 0 8 7 6 0 0 1 5 1 0 0 0 Low Addr. High Addr. Effective address+1 15 8 7 0 PC User's Manual U14046EJ5V0UD 123 CHAPTER 5 CPU ARCHITECTURE 5.3.4 Register addressing [Function] Register pair (AX) contents to be specified with an instruction word are transferred to the program counter (PC) and branched. This function is carried out when the BR AX instruction is executed. [Illustration] 7 rp 0 7 A 15 X 8 7 PC 124 0 User's Manual U14046EJ5V0UD 0 CHAPTER 5 CPU ARCHITECTURE 5.4 Operand Address Addressing The following various methods are available to specify the register and memory (addressing) which undergo manipulation during instruction execution. 5.4.1 Implied addressing [Function] The register which functions as an accumulator (A and AX) in the general-purpose register is automatically (implicitly) addressed. Of the PD780024A, 780034A, 780024AY, 780034AY Subseries instruction words, the following instructions employ implied addressing. Instruction Register to Be Specified by Implied Addressing MULU A register for multiplicand and AX register for product storage DIVUW AX register for dividend and quotient storage ADJBA/ADJBS A register for storage of numeric values which become decimal correction targets ROR4/ROL4 A register for storage of digit data which undergoes digit rotation [Operand format] Because implied addressing can be automatically employed with an instruction, no particular operand format is necessary. [Description example] In the case of MULU X With an 8-bit x 8-bit multiply instruction, the product of A register and X register is stored in AX. In this example, the A and AX registers are specified by implied addressing. User's Manual U14046EJ5V0UD 125 CHAPTER 5 CPU ARCHITECTURE 5.4.2 Register addressing [Function] The general-purpose register to be specified is accessed as an operand with the register specify code (Rn and RPn) of an instruction word in the registered bank specified with the register bank select flag (RBS0 and RBS1). Register addressing is carried out when an instruction with the following operand format is executed. When an 8-bit register is specified, one of the eight registers is specified with 3 bits in the operation code. [Operand format] Identifier Description r X, A, C, B, E, D, L, H rp AX, BC, DE, HL `r' and `rp' can be described with absolute names (R0 to R7 and RP0 to RP3) as well as function names (X, A, C, B, E, D, L, H, AX, BC, DE, and HL). [Description example] MOV A, C; when selecting C register as r Operation code 0 1 1 0 0 0 1 0 Register specify code INCW DE; when selecting DE register pair as rp Operation code 1 0 0 0 0 1 0 0 Register specify code 126 User's Manual U14046EJ5V0UD CHAPTER 5 CPU ARCHITECTURE 5.4.3 Direct addressing [Function] The memory to be manipulated is addressed with immediate data in an instruction word becoming an operand address. [Operand format] Identifier Description addr16 Label or 16-bit immediate data [Description example] MOV A, !0FE00H; when setting !addr16 to FE00H Operation code 1 0 0 0 1 1 1 0 OP code 0 0 0 0 0 0 0 0 00H 1 1 1 1 1 1 1 0 FEH [Illustration] 7 0 OP code addr16 (lower) addr16 (upper) Memory User's Manual U14046EJ5V0UD 127 CHAPTER 5 CPU ARCHITECTURE 5.4.4 Short direct addressing [Function] The memory to be manipulated in the fixed space is directly addressed with 8-bit data in an instruction word. This addressing is applied to the 256-byte space FE20H to FF1FH. Internal RAM and special function registers (SFRs) are mapped at FE20H to FEFFH and FF00H to FF1FH, respectively. If the SFR area (FF00H to FF1FH) where short direct addressing is applied, ports which are frequently accessed in a program and compare and capture registers of the timer/event counter are mapped, and these SFRs can be manipulated with a small number of bytes and clocks. When 8-bit immediate data is at 20H to FFH, bit 8 of an effective address is cleared to 0. When it is at 00H to 1FH, bit 8 is set to 1. See the [Illustration] below. [Operand format] Identifier Description saddr Label or immediate data indicating FE20H to FF1FH saddrp Label or immediate data indicating FE20H to FF1FH (even address only) [Description example] MOV 0FE30H, A; when transferring the value in register A to saddr (FE30H) Operation code 1 1 1 1 0 0 1 0 OP code 0 0 1 1 0 0 0 0 30H (saddr-offset) [Illustration] 7 0 OP code saddr-offset Short direct memory 8 7 15 Effective address 1 1 1 1 1 1 1 When 8-bit immediate data is 20H to FFH, = 0 When 8-bit immediate data is 00H to 1FH, = 1 128 User's Manual U14046EJ5V0UD 0 CHAPTER 5 CPU ARCHITECTURE 5.4.5 Special function register (SFR) addressing [Function] The memory-mapped special function register (SFR) is addressed with 8-bit immediate data in an instruction word. This addressing is applied to the 240-byte spaces FF00H to FFCFH and FFE0H to FFFFH. However, the SFR mapped at FF00H to FF1FH can be accessed with short direct addressing. [Operand format] Identifier Description sfr Special function register name sfrp 16-bit manipulatable special function register name (even address only) [Description example] MOV PM0, A; when selecting PM0 (FF20H) as sfr Operation code 1 1 1 1 0 1 1 0 OP code 0 0 1 0 0 0 0 0 20H (sfr-offset) [Illustration] 7 0 OP code sfr-offset SFR 15 Effective address 1 8 7 1 1 1 1 1 1 0 1 User's Manual U14046EJ5V0UD 129 CHAPTER 5 CPU ARCHITECTURE 5.4.6 Register indirect addressing [Function] Register pair contents specified with a register pair specify code in an instruction word of the register bank specified with a register bank select flag (RBS0 and RBS1) serve as an operand address for addressing the memory to be manipulated. This addressing can be carried out for all the memory spaces. [Operand format] Identifier - Description [DE], [HL] [Description example] MOV A, [DE]; when selecting [DE] as register pair Operation code 1 0 0 0 0 1 0 1 [Illustration] 16 DE 8 7 0 E D 7 Memory The contents of the memory addressed are transferred. 7 0 A 130 User's Manual U14046EJ5V0UD 0 The memory address specified with the register pair DE CHAPTER 5 CPU ARCHITECTURE 5.4.7 Based addressing [Function] 8-bit immediate data is added as offset data to the contents of the base register, that is, the HL register pair in an instruction word of the register bank specified by the register bank select flags (RBS0 and RBS1) and the sum is used to address the memory. Addition is performed by expanding the offset data as a positive number to 16 bits. A carry from the 16th bit is ignored. This addressing can be carried out for all the memory spaces. [Operand format] Identifier Description - [HL + byte] [Description example] MOV A, [HL + 10H]; when setting byte to 10H Operation code 1 0 1 0 1 1 1 0 0 0 0 1 0 0 0 0 [Illustration] 8 7 16 HL H 0 L +10 7 The contents of the memory addressed are transferred. 7 Memory 0 0 A User's Manual U14046EJ5V0UD 131 CHAPTER 5 CPU ARCHITECTURE 5.4.8 Based indexed addressing [Function] The B or C register contents specified in an instruction word are added to the contents of the base register, that is, the HL register pair in the register bank specified by the register bank select flags (RBS0 and RBS1) and the sum is used to address the memory. Addition is performed by expanding the B or C register contents as a positive number to 16 bits. A carry from the 16th bit is ignored. This addressing can be carried out for all the memory spaces. [Operand format] Identifier Description - [HL + B], [HL + C] [Description example] In the case of MOV A, [HL + B] (selecting the B register) Operation code 1 0 1 0 1 0 1 1 [Illustration] 16 HL 8 7 H 0 L + 7 B 7 Memory The contents of the memory addressed are transferred. 7 0 A 132 User's Manual U14046EJ5V0UD 0 0 CHAPTER 5 CPU ARCHITECTURE 5.4.9 Stack addressing [Function] The stack area is indirectly addressed with the stack pointer (SP) contents. This addressing method is automatically employed when the PUSH, POP, subroutine call and return instructions are executed or the register is saved/reset upon generation of an interrupt request. Stack addressing can be used to address the internal high-speed RAM area only. [Description example] In the case of PUSH DE (saving the DE register) Operation code 1 0 1 1 0 1 0 1 [Illustration] 7 SP SP FEE0H FEDEH Memory 0 FEE0H FEDFH D FEDEH E User's Manual U14046EJ5V0UD 133 CHAPTER 6 PORT FUNCTIONS 6.1 Port Functions The PD780024A, 780034A, 780024AY, and 780034AY Subseries products incorporate eight input ports and 43 I/O ports. Figure 6-1 shows the port configuration. Every port is capable of 1-bit and 8-bit manipulations and can carry out considerably varied control operations. Besides port functions, the ports can also serve as on-chip hardware I/O pins. Figure 6-1. Port Types Port 5 P50 Port 6 P64 P67 P17 Port 7 P70 P20 P75 P25 P00 P03 P10 P57 P30 P36 P40 P47 134 User's Manual U14046EJ5V0UD Port 0 Port 1 Port 2 Port 3 Port 4 CHAPTER 6 PORT FUNCTIONS Table 6-1. Port Functions (PD780024A, 780034A Subseries) Pin Name Function Alternate Function P00 Port 0 INTP0 P01 4-bit I/O port. INTP1 P02 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. P03 INTP2 INTP3/ADTRG P10 to P17 Port 1 8-bit input-only port. ANI0 to ANI7 P20 Port 2 SI30 P21 6-bit I/O port. SO30 P22 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. SCK30 P23 RxD0 P24 TxD0 P25 ASCK0 P30 Port 3 N-ch open-drain I/O port. P31 7-bit I/O port. On-chip pull-up resistor can be specified by mask P32 Input/output mode can be specified option (mask ROM version only). in 1-bit units. LEDs can be driven directly. - P33 P34 An on-chip pull-up resistor can be specified by SI31 P35 software settings. SO31 P36 SCK31 P40 to P47 Port 4 8-bit I/O port. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be specified by software settings. Interrupt request flag (KRIF) is set to 1 by falling edge detection. AD0 to AD7 P50 to P57 Port 5 8-bit I/O port. LEDs can be driven directly. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. A8 to A15 P64 Port 6 RD P65 4-bit I/O port. WR P66 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. P67 P70 P71 P72 WAIT ASTB Port 7 6-bit I/O port. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. TI00/TO0 TI01 TI50/TO50 P73 TI51/TO51 P74 PCL P75 BUZ User's Manual U14046EJ5V0UD 135 CHAPTER 6 PORT FUNCTIONS Table 6-2. Port Functions (PD780024AY, 780034AY Subseries) Pin Name Function Alternate Function P00 Port 0 INTP0 P01 4-bit I/O port. INTP1 P02 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. P03 INTP2 INTP3/ADTRG P10 to P17 Port 1 8-bit input-only port. ANI0 to ANI7 P20 Port 2 SI30 P21 6-bit I/O port SO30 P22 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. SCK30 P23 RxD0 P24 TxD0 P25 ASCK0 P30 Port 3 N-ch open-drain I/O port. P31 7-bit I/O port. On-chip pull-up resistor can be specified by mask P32 Input/output mode can be specified option (P30 and P31 are mask ROM version only). in 1-bit units. LEDs can be driven directly. P33 - SDA0 SCL0 P34 - An on-chip pull-up resistor can be used by software settings. P35 P36 P40 to P47 Port 4 8-bit I/O port. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. Interrupt request flag (KRIF) is set to 1 by falling edge detection. AD0 to AD7 P50 to P57 Port 5 8-bit I/O port. LEDs can be driven directly. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. A8 to A15 P64 Port 6 RD P65 4-bit I/O port. WR P66 Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. P67 P70 P71 P72 WAIT ASTB Port 7 6-bit I/O port. Input/output mode can be specified in 1-bit units. An on-chip pull-up resistor can be used by software settings. TI00/TO0 TI01 TI50/TO50 P73 TI51/TO51 P74 PCL P75 BUZ 136 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS 6.2 Port Configuration A port consists of the following hardware. Table 6-3. Port Configuration Item Configuration Control register Port mode register (PMm: m = 0, 2 to 7) Pull-up resistor option register (PUm: m = 0, 2 to 7) Port Total: 51 ports (8 inputs, 43 inputs/outputs) Pull-up resistor * Mask ROM version Total: 43 (software control: 39, mask option: 4Note) * Flash memory version Total: 39 Note Two mask options for the PD780024AY and 780034AY Subseries. 6.2.1 Port 0 Port 0 is a 4-bit I/O port with output latch. P00 to P03 pins can specify the input mode/output mode in 1-bit units with port mode register 0 (PM0). An on-chip pull-up resistor of P00 to P03 pins can be used for them in 1-bit units with pull-up resistor option register 0 (PU0). This port can also be used as an external interrupt request input and A/D converter external trigger input. RESET input sets port 0 to input mode. Figure 6-2 shows a block diagram of port 0. Cautions 1. Port 0 functions alternately as an external interrupt request input pin. If the output mode of the port function is specified and the output level of the port is changed while interrupts are not disabled by the external interrupt rising edge enable register (EGP) and external interrupt falling edge enable register (EGN), the interrupt request flag is set. Thus, when the output mode is used, set the interrupt mask flag to 1. 2. When the external interrupt request function is switched to the port function, edge detection may be performed. Therefore, clear bit n (EGPn) of EGP and bit n (EGNn) of EGN to 0 before selecting the port mode. 3. When using P03/INTP3/ADTRG as an A/D converter external trigger input, specify valid edges by setting bits 1 and 2 (EGA00 and EGA01) of A/D converter mode register 0 (ADM0) and set the interrupt mask flag (PMK3) to 1. Remark n = 0 to 3 User's Manual U14046EJ5V0UD 137 CHAPTER 6 PORT FUNCTIONS Figure 6-2. Block Diagram of P00 to P03 VDD0 WRPU PU00 to PU03 P-ch Alternate function Selector Internal bus RD WRPORT P00/INTP0 Output latch (P00 to P03) P02/INTP2, P03/INTP3/ADTRG WRPM PM00 to PM03 PU: Pull-up resistor option register PM: Port mode register RD: Port 0 read signal WR: Port 0 write signal 138 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS 6.2.2 Port 1 Port 1 is an 8-bit input-only port. This port can also be used as an A/D converter analog input. Figure 6-3 shows a block diagram of port 1. Figure 6-3. Block Diagram of P10 to P17 Internal bus RD A/D converter P10/ANI0 to P17/ANI7 RD: Port 1 read signal User's Manual U14046EJ5V0UD 139 CHAPTER 6 PORT FUNCTIONS 6.2.3 Port 2 Port 2 is a 6-bit I/O port with output latch. P20 to P25 pins can specify the input mode/output mode in 1-bit units with port mode register 2 (PM2). An on-chip pull-up resistor of P20 to P25 pins can be used for them in 1-bit units with pull-up resistor option register 2 (PU2). This port has also alternate functions as serial interface data I/O and clock I/O. RESET input sets port 2 to input mode. Figures 6-4 to 6-6 show block diagrams of port 2. Figure 6-4. Block Diagram of P20, P23, and P25 VDD0 WRPU PU20, PU23, PU25 P-ch Alternate function Selector Internal bus RD WRPORT P20/SI30, P23/RxD0, P25/ASCK0 Output latch (P20, P23, P25) WRPM PM20, PM23, PM25 PU: Pull-up resistor option register PM: Port mode register RD: Port 2 read signal WR: Port 2 write signal 140 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-5. Block Diagram of P21 and P24 VDD0 WRPU PU21, PU24 P-ch Selector Internal bus RD WRPORT Output latch (P21, P24) P21/SO30, P24/TxD0 WRPM PM21, PM24 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 2 read signal WR: Port 2 write signal User's Manual U14046EJ5V0UD 141 CHAPTER 6 PORT FUNCTIONS Figure 6-6. Block Diagram of P22 VDD0 WRPU PU22 P-ch Alternate function Selector Internal bus RD WRPORT Output latch (P22) P22/SCK30 WRPM PM22 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 2 read signal WR: Port 2 write signal 142 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS 6.2.4 Port 3 (PD780024A, 780034A Subseries) Port 3 is a 7-bit I/O port with output latch. P30 to P36 pins can specify the input mode/output mode in 1-bit units with port mode register 3 (PM3). This port has the following functions for pull-up resistors. These functions differ depending on the port's higher 3-bit/lower 4-bit, and whether the product is a mask ROM version or a flash memory version. Table 6-4. Pull-Up Resistor of Port 3 (PD780024A, 780034A Subseries) Higher 3-Bit (P34 to P36 Pins) Mask ROM version An on-chip pull-up resistor can be connected in 1-bit units by PU3 Flash memory version Lower 4-Bit (P30 to P33 Pins) An on-chip pull-up resistor can be specified in 1-bit units by mask option On-chip pull-up resistor is not provided PU3: Pull-up resistor option register 3 The P30 to P33 pins can drive LEDs directly. The P34 to P36 pins can also be used for serial interface data I/O and clock I/O. RESET input sets port 3 to input mode. Figures 6-7 to 6-11 show block diagrams of port 3. Figure 6-7. Block Diagram of P30 and P31 (PD780024A, 780034A Subseries) VDD0 RD Mask option resistor Internal bus Selector Mask ROM version only No pull-up resistor for flash memory version P30, P31 WRPORT Output latch (P30, P31) N-ch WRPM PM30, PM31 PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal User's Manual U14046EJ5V0UD 143 CHAPTER 6 PORT FUNCTIONS Figure 6-8. Block Diagram of P32 and P33 (PD780024A, 780034A Subseries) VDD0 Mask option resistor Mask ROM version only No pull-up resistor for flash memory version Internal bus Selector RD P32, P33 WRPORT Output latch (P32, P33) N-ch WRPM PM32, PM33 PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal 144 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-9. Block Diagram of P34 (PD780024A, 780034A Subseries) VDD0 WRPU PU34 P-ch Alternate function Selector Internal bus RD WRPORT Output latch (P34) P34/SI31 WRPM PM34 PU: Pull-up resistor option register PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal User's Manual U14046EJ5V0UD 145 CHAPTER 6 PORT FUNCTIONS Figure 6-10. Block Diagram of P35 (PD780024A, 780034A Subseries) VDD0 WRPU PU35 P-ch Selector Internal bus RD WRPORT Output latch (P35) P35/SO31 WRPM PM35 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal 146 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-11. Block Diagram of P36 (PD780024A, 780034A Subseries) VDD0 WRPU PU36 P-ch Alternate function Selector Internal bus RD WRPORT Output latch (P36) P36/SCK31 WRPM PM36 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal User's Manual U14046EJ5V0UD 147 CHAPTER 6 PORT FUNCTIONS 6.2.5 Port 3 (PD780024AY, 780034AY Subseries) Port 3 is a 7-bit I/O port with output latch. P30 to P36 pins can specify the input mode/output mode in 1-bit units with port mode register 3 (PM3). This port has the following functions for pull-up resistors. These functions differ depending on port's bits location and mask ROM version/flash memory version. Table 6-5. Pull-Up Resistor of Port 3 (PD780024AY, 780034AY Subseries) P34 to P36 Pins P30 and P31 Pins Mask ROM version An on-chip pull-up resistor can An on-chip pull-up resistor can be specified be connected in 1-bit units by in 1-bit units by mask option Flash memory version PU3 On-chip pull-up resistor is not provided PU3: Pull-up resistor option register 3 Caution P32 and P33 pins have no pull-up resistor. The P30 to P33 pins can drive LEDs directly. The P32 and P33 pins can also be used for serial interface data I/O and clock I/O. RESET input sets port 3 to input mode. Figures 6-12 to 6-15 show block diagrams of port 3. 148 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-12. Block Diagram of P30 and P31 (PD780024AY, 780034AY Subseries) VDD0 RD Mask option resistor Selector Mask ROM version only No pull-up resistor for flash memory version P30, P31 Internal bus WRPORT Output latch (P30, P31) N-ch WRPM PM30, PM31 PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal Figure 6-13. Block Diagram of P32 and P33 (PD780024AY, 780034AY Subseries) Internal bus Selector RD P32/SDA0, P33/SCL0 WRPORT Output latch (P32, P33) N-ch WRPM PM32, PM33 Alternate function PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal User's Manual U14046EJ5V0UD 149 CHAPTER 6 PORT FUNCTIONS Figure 6-14. Block Diagram of P34 and P36 (PD780024AY, 780034AY Subseries) VDD0 WRPU PU34, PU36 P-ch Selector Internal bus RD WRPORT Output latch (P34, P36) P34, P36 WRPM PM34, PM36 PU: Pull-up resistor option register PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal 150 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-15. Block Diagram of P35 (PD780024AY, 780034AY Subseries) VDD0 WRPU PU35 P-ch Selector Internal bus RD WRPORT Output latch (P35) P35 WRPM PM35 PU: Pull-up resistor option register PM: Port mode register RD: Port 3 read signal WR: Port 3 write signal User's Manual U14046EJ5V0UD 151 CHAPTER 6 PORT FUNCTIONS 6.2.6 Port 4 Port 4 is an 8-bit I/O port with output latch. The P40 to P47 pins can specify the input mode/output mode in 1bit units with port mode register 4 (PM4). An on-chip pull-up resistor of P40 to P47 pins can be used for them in 1bit units with pull-up resistor option register 4 (PU4). The interrupt request flag (KRIF) can be set to 1 by detecting falling edges. This port can also be used as an address/data bus in external memory expansion mode. RESET input sets port 4 to input mode. Figures 6-16 and 6-17 show a block diagram of port 4 and block diagram of the falling edge detector, respectively. Cautions 1. The internal pull-up resistor is not disconnected even if the external memory expansion mode is set when PU4n = 1 (n = 0 to 7). 2. When using the falling edge detection interrupt (INTKR), be sure to set the memory expansion mode register (MEM) to 01H. Figure 6-16. Block Diagram of P40 to P47 VDD0 WRPU PU40 to PU47 P-ch Alternate function RD Internal bus Selector WRPORT Output latch (P40 to P47) WRPM Selector Alternate function Memory expansion mode register (MEM) PM40 to PM47 PU: Pull-up resistor option register PM: Port mode register RD: Port 4 read signal WR: Port 4 write signal 152 User's Manual U14046EJ5V0UD P40/AD0 to P47/AD7 CHAPTER 6 PORT FUNCTIONS Figure 6-17. Block Diagram of Falling Edge Detector P40 P41 P42 P43 Falling edge detector P44 INTKR P45 P46 P47 "1" when MEM = 01H 6.2.7 Port 5 Port 5 is an 8-bit I/O port with output latch. The P50 to P57 pins can specify the input mode/output mode in 1bit units with port mode register 5 (PM5). An on-chip pull-up resistor of P50 to P57 pins can be used for them in 1bit units with pull-up resistor option register 5 (PU5). Port 5 can drive LEDs directly. This port can also be used as an address bus in external memory expansion mode. RESET input sets port 5 to input mode. Figure 6-18 shows a block diagram of port 5. Caution The internal pull-up resistor is not disconnected even if the external memory expansion mode is set when PU5n = 1 (n = 0 to 7). Figure 6-18. Block Diagram of P50 to P57 VDD0 WRPU PU50 to PU57 P-ch RD Internal bus Selector WRPORT Output latch (P50 to P57) Selector Alternate function WRPM P50/A8 to P57/A15 Memory expansion mode register (MEM) PM50 to PM57 PU: Pull-up resistor option register PM: Port mode register RD: Port 5 read signal WR: Port 5 write signal User's Manual U14046EJ5V0UD 153 CHAPTER 6 PORT FUNCTIONS 6.2.8 Port 6 Port 6 is a 4-bit I/O port with output latch. The P64 to P67 pins can specify the input mode/output mode in 1-bit units with port mode register 6 (PM6). An on-chip pull-up resistor of P64 to P67 pins can be used for them in 1-bit units with pull-up resistor option register 6 (PU6). This port can also be used as a control signal output in external memory expansion mode. RESET input sets port 6 to input mode. Figures 6-19 and 6-20 show block diagrams of port 6. Cautions 1. The internal pull-up resistor is not disconnected even if the external memory expansion mode is set when PU6n = 1 (n = 4 to 7). 2. When external wait is not used in external memory expansion mode, P66 can be used as an I/O port. Figure 6-19. Block Diagram of P64, P65, and P67 VDD0 WRPU PU64, PU65, PU67 P-ch RD Internal bus Selector WRPORT Output latch (P64, P65, P67) WRPM Selector Alternate function Memory expansion mode register (MEM) PM64, PM65, PM67 PU: Pull-up resistor option register PM: Port mode register RD: Port 6 read signal WR: Port 6 write signal 154 User's Manual U14046EJ5V0UD P64/RD, P65/WR, P67/ASTB CHAPTER 6 PORT FUNCTIONS Figure 6-20. Block Diagram of P66 VDD0 WRPU PU66 P-ch Alternate function RD Internal bus Selector WRPORT Output latch (P66) Selector P66/WAIT Memory expansion mode register (MEM) WRPM PM66 PU: Pull-up resistor option register PM: Port mode register RD: Port 6 read signal WR: Port 6 write signal User's Manual U14046EJ5V0UD 155 CHAPTER 6 PORT FUNCTIONS 6.2.9 Port 7 Port 7 is a 6-bit I/O port with output latch. The P70 to P75 pins can specify the input mode/output mode in 1-bit units with port mode register 7 (PM7). An on-chip pull-up resistor of P70 to P75 pins can be used for them in 1-bit units with pull-up resistor option register 7 (PU7). This port can also be used as a timer I/O, clock output, and buzzer output. RESET input sets the input mode. Figures 6-21 to 6-23 show block diagrams of port 7. Figure 6-21. Block Diagram of P70, P72, and P73 VDD0 WRPU PU70, PU72, PU73 P-ch Alternate function Selector Internal bus RD WRPORT Output latch (P70, P72, P73) P70/TI00/TO0, P72/TI50/TO50, P73/TI51/TO51 WRPM PM70, PM72, PM73 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 7 read signal WR: Port 7 write signal 156 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Figure 6-22. Block Diagram of P71 VDD0 WRPU PU71 P-ch Alternate function Selector Internal bus RD WRPORT Output latch (P71) P71/TI01 WRPM PM71 PU: Pull-up resistor option register PM: Port mode register RD: Port 7 read signal WR: Port 7 write signal User's Manual U14046EJ5V0UD 157 CHAPTER 6 PORT FUNCTIONS Figure 6-23. Block Diagram of P74 and P75 VDD0 WRPU PU74, PU75 P-ch Selector Internal bus RD WRPORT Output latch (P74, P75) P74/PCL, P75/BUZ WRPM PM74, PM75 Alternate function PU: Pull-up resistor option register PM: Port mode register RD: Port 7 read signal WR: Port 7 write signal 158 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS 6.3 Port Function Control Registers The following two types of registers control the ports. * Port mode registers (PM0, PM2 to PM7) * Pull-up resistor option registers (PU0, PU2 to PU7) (1) Port mode registers (PM0, PM2 to PM7) These registers are used to set port input/output in 1-bit units. PM0 and PM2 to PM7 are independently set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets registers to FFH. When using a port pin as its alternate-function pin, set the port mode registers and output latches as shown in Table 6-6. Cautions 1. Pins P10 to P17 are input-only pins. 2. Port 0 functions alternately as an external interrupt request input pin. If the output mode of the port function is specified and the output level of the port is changed while interrupts are not disabled by the external interrupt rising edge enable register (EGP) and external interrupt falling edge enable register (EGN), the interrupt request flag is set. When the output mode is used, therefore, the interrupt mask flag should be set to 1 beforehand. 3. If a port has an alternate function pin and it is used as an alternate output function, clear the corresponding output latches (P0 and P2 to P7) to 0. User's Manual U14046EJ5V0UD 159 CHAPTER 6 PORT FUNCTIONS Figure 6-24. Format of Port Mode Register (PM0, PM2 to PM7) Address: FF20H After Reset: FFH Symbol 7 6 5 4 3 2 1 0 PM0 1 1 1 1 PM03 PM02 PM01 PM00 Address: FF22H After Reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 Address: FF23H After Reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM3 1 PM36 PM35 PM34 PM33 PM32 PM31 PM30 Address: FF24H After Reset: FFH Symbol PM4 Symbol PM5 6 5 4 3 2 1 0 PM47 PM46 PM45 PM44 PM43 PM42 PM41 PM40 PM6 R/W 7 6 5 4 3 2 1 0 PM57 PM56 PM55 PM54 PM53 PM52 PM51 PM50 Address: FF26H After Reset: FFH Symbol R/W 7 Address: FF25H After Reset: FFH R/W 7 6 5 4 3 2 1 0 PM67 PM66 PM65 PM64 1 1 1 1 Address: FF27H After Reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM7 1 1 PM75 PM74 PM73 PM72 PM71 PM70 PMmn 160 R/W Pmn Pin I/O Mode Selection (m = 0, 2 to 7; n = 0 to 7) 0 Output mode (Output buffer on) 1 Input mode (Output buffer off) User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS Table 6-6. Port Mode Registers and Output Latch Settings When Alternate Function Is Used (1/2) Alternate Function Pin Name Name PMxx Pxx I/O P00 to P02 INTP0 to INTP2 Input 1 x P03 INTP3 Input 1 x ADTRG Input 1 x P10 to P17 ANI0 to ANI7 Input 1 (fix) x P20 SI30 Input 1 x P21 SO30 Output 0 0 P22 SCK30 Input 1 x Output 0 0 P23 RxD0 Input 1 x P24 TxD0 Output 0 0 P25 ASCK0 Input 1 x P32 SDA0Note 1 I/O 0 0 P33 SCL0 Note 1 I/O 0 0 P34 SI31 Input 1 x P35 SO31 Output 0 0 P36 SCK31 Input 1 x Output 0 0 P40 to P47 AD0 to AD7 I/O x P50 to P57 A8 to A15 Output xNote 2 P64 RD Output xNote 2 P65 WR Output xNote 2 P66 WAIT Input P67 ASTB Output Note 2 xNote 2 1Note 2 xNote 2 Notes 1. PD780024AY, 780034AY Subseries only 2. When using the P40 to P47, P50 to P57, and P64 to P67 pins as alternate-function pins, set the function using the memory expansion mode register (MEM). Remark x: Don't care PMxx: Port mode register Pxx: Port output latch User's Manual U14046EJ5V0UD 161 CHAPTER 6 PORT FUNCTIONS Table 6-6. Port Mode Registers and Output Latch Settings When Alternate Function Is Used (2/2) Pin Name Alternate Function Name PMxx Pxx I/O TI00 Input 1 x TO0 Output 0 0 P71 TI01 Input 1 x P72 TI50 Input 1 x TO50 Output 0 0 TI51 Input 1 x P70 P73 TO51 Output 0 0 P74 PCL Output 0 0 P75 BUZ Output 0 0 Remark x: Don't care PMxx: Port mode register Pxx: 162 Port output latch User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS (2) Pull-up resistor option registers (PU0, PU2 to PU7) These registers are used to set whether to use an on-chip pull-up resistor at each port or not. By setting PU0 and PU2 to PU7, the on-chip pull-up resistors of the port pins corresponding to the bits in PU0 and PU2 to PU7 can be used. PU0 and PU2 to PU7 are independently set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears registers to 00H. Cautions 1. The P10 to P17 pins do not incorporate a pull-up resistor. 2. Pins P30 to P33 (in PD780024AY and 780034AY Subseries, P30 and P31 pins) can be used with pull-up resistor by mask option only for mask ROM version. 3. When PUm is set to 1, the on-chip pull-up resistor is connected irrespective of the input/ output mode. When using in output mode, clear the bit of PUm to 0 (m = 0, 2 to 7). User's Manual U14046EJ5V0UD 163 CHAPTER 6 PORT FUNCTIONS Figure 6-25. Format of Pull-Up Resistor Option Register (PU0, PU2 to PU7) Address: FF30H After Reset: 00H Symbol 7 6 5 4 3 2 1 0 PU0 0 0 0 0 PU03 PU02 PU01 PU00 Address: FF32H After Reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 PU2 0 0 PU25 PU24 PU23 PU22 PU21 PU20 Address: FF33H After Reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 PU3 0 PU36 PU35 PU34 0 0 0 0 Address: FF34H After Reset: 00H Symbol PU4 Symbol PU5 6 5 4 3 2 1 0 PU47 PU46 PU45 PU44 PU43 PU42 PU41 PU40 PU6 R/W 7 6 5 4 3 2 1 0 PU57 PU56 PU55 PU54 PU53 PU52 PU51 PU50 Address: FF36H After Reset: 00H Symbol R/W 7 Address: FF35H After Reset: 00H R/W 7 6 5 4 3 2 1 0 PU67 PU66 PU65 PU64 0 0 0 0 Address: FF37H After Reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 PU7 0 0 PU75 PU74 PU73 PU72 PU71 PU70 PUmn 164 R/W Pmn Pin On-Chip Pull-Up Resistor Selection (m = 0, 2 to 7; n = 0 to 7) 0 On-chip pull-up resistor not used 1 On-chip pull-up resistor used User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS 6.4 Port Function Operations Port operations differ depending on whether the input or output mode is set, as shown below. Caution In the case of 1-bit memory manipulation instruction, although a single bit is manipulated, the port is accessed as an 8-bit unit. Therefore, on a port with a mixture of input and output pins, the output latch contents for pins specified as input are undefined, even for bits other than the manipulated bit. 6.4.1 Writing to I/O port (1) Output mode A value is written to the output latch by a transfer instruction, and the output latch contents are output from the pin. Once data is written to the output latch, it is retained until data is written to the output latch again. The output latch data is cleared by reset. (2) Input mode A value is written to the output latch by a transfer instruction, but since the output buffer is off, the pin status does not change. Once data is written to the output latch, it is retained until data is written to the output latch again. 6.4.2 Reading from I/O port (1) Output mode The output latch contents are read by a transfer instruction. The output latch contents do not change. (2) Input mode The pin status is read by a transfer instruction. The output latch contents do not change. 6.4.3 Operations on I/O port (1) Output mode An operation is performed on the output latch contents, and the result is written to the output latch. The output latch contents are output from the pins. Once data is written to the output latch, it is retained until data is written to the output latch again. The output latch data is cleared by reset. (2) Input mode The output latch contents are undefined, but since the output buffer is off, the pin status does not change. User's Manual U14046EJ5V0UD 165 CHAPTER 6 PORT FUNCTIONS 6.5 Selection of Mask Option The following mask option is provided in the mask ROM version. The flash memory versions have no mask options. Table 6-7. Comparison Between Mask ROM Version and Flash Memory Version Pin Name Mask option for pins P30 to P33Note Mask ROM Version On-chip pull-up resistors can be specified in 1-bit units. Flash Memory Version An on-chip pull-up resistor is not provided. Note For PD780024AY and 780034AY Subseries products, only the P30 and P31 pins can incorporate a pullup resistor. 166 User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR 7.1 Clock Generator Functions The clock generator generates the clock to be supplied to the CPU and peripheral hardware. The following two types of system clock oscillators are available. (1) Main system clock oscillator This circuit oscillates a clock with the following frequencies. * 1.0 to 8.38 MHz: Conventional product of PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A and PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY, 78F0034A, 78F0034AY, 78F0034BY * 1.0 to 12 MHz: Expanded-specification product of PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A and PD78F0034B Oscillation can be stopped by executing the STOP instruction or setting the processor clock control register (PCC). (2) Subsystem clock oscillator The circuit oscillates a clock with a frequency of 32.768 kHz. Oscillation cannot be stopped. If the subsystem clock oscillator is not used, the internal feedback resistor can be disabled by the processor clock control register (PCC). This enables to reduce the power consumption in the STOP mode. 7.2 Clock Generator Configuration The clock generator consists of the following hardware. Table 7-1. Clock Generator Configuration Item Configuration Control registers Processor clock control register (PCC) Oscillation stabilization time select register (OSTS) Oscillators Main system clock oscillator Subsystem clock oscillator Controllers Prescaler Standby controller Wait controller User's Manual U14046EJ5V0UD 167 CHAPTER 7 CLOCK GENERATOR Figure 7-1. Block Diagram of Clock Generator Internal bus Oscillation stabilization time select register (OSTS) FRC OSTS2 OSTS1 OSTS0 XT1 XT2 Subsystem clock oscillator fXT Watch timer, clock output function Prescaler 1/2 X1 X2 Main system clock oscillator Prescaler fX fX 22 fX 23 fXT 2 fX 24 3 Selector fX 2 Clock to peripheral hardware Standby controller Wait controller HALT 3 STOP MCC FRC CLS CSS PCC2 PCC1 PCC0 Processor clock control register (PCC) Internal bus 168 User's Manual U14046EJ5V0UD CPU clock (fCPU) CHAPTER 7 CLOCK GENERATOR 7.3 Clock Generator Control Registers The clock generator is controlled by the following two registers. * Processor clock control register (PCC) * Oscillation stabilization time select register (OSTS) (1) Processor clock control register (PCC) This register selects the CPU clock and the division ratio, sets main system clock oscillator operation/stop and sets whether to use the subsystem clock oscillator internal feedback resistorNote. PCC is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets the value of PCC to 04H. Note The feedback resistor is required to control the bias point of the oscillation waveform so that the bias point is in the middle of the power supply voltage. When the subsystem clock is not used, the power consumption in the STOP mode can be reduced by setting bit 6 (FRC) of PCC to 1 (see Figure 7-7 Subsystem Clock Feedback Resistor). User's Manual U14046EJ5V0UD 169 CHAPTER 7 CLOCK GENERATOR Figure 7-2. Format of Processor Clock Control Register (PCC) Address: FFFBH After reset: 04H R/WNote 1 Symbol <7> <6> <5> <4> 3 2 1 0 PCC MCC FRC CLS CSS 0 PCC2 PCC1 PCC0 Main system clock oscillation controlNote 2 MCC 0 Oscillation possible 1 Oscillation stopped FRC Subsystem clock feedback resistor selection 0 Internal feedback resistor used 1 Internal feedback resistor not usedNote 3 CLS CPU clock status 0 Main system clock 1 Subsystem clock CSS PCC2 PCC1 PCC0 0 0 0 0 fX 0 0 1 fX/2 0 1 0 fX/22 0 1 1 fX/23 1 0 0 fX/24 0 0 0 fXT/2 0 0 1 0 1 0 0 1 1 1 0 0 1 Other than above CPU clock (fCPU) selection Setting prohibited Notes 1. Bit 5 is read-only. 2. When the CPU is operating on the subsystem clock, MCC should be used to stop the main system clock oscillation. The STOP instruction should not be used. 3. This bit can be set to 1 only when the subsystem clock is not used. Cautions 1. Be sure to clear bit 3 to 0. 2. When the external clock is input, MCC should not be set. This is because the X2 pin is connected to VDD1 via a pull-up resistor. Remarks 1. fX: Main system clock oscillation frequency 2. fXT: Subsystem clock oscillation frequency 170 User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR The fastest instructions of the PD780024A, 780034A, 780024AY, and 780034AY Subseries are carried out in two CPU clocks. The relationship between the CPU clock (fCPU) and minimum instruction execution time is shown in Table 7-2. Table 7-2. Relationship Between CPU Clock and Minimum Instruction Execution Time CPU Clock (fCPU) Minimum Instruction Execution Time: 2/fCPU fX = 8.38 MHz fX = 12 MHzNote fXT = 32.768 kHz fX 0.238 s 0.166 s - fX/2 0.477 s 0.333 s - fX/22 0.954 s 0.666 s - fX/23 1.90 s 1.33 s - fX/24 3.81 s 2.66 s - fXT/2 - - 122 s Note Expanded-specification products of PD780024A, 780034A Subseries only Remark fX: Main system clock oscillation frequency fXT: Subsystem clock oscillation frequency User's Manual U14046EJ5V0UD 171 CHAPTER 7 CLOCK GENERATOR (2) Oscillation stabilization time select register (OSTS) This register is used to select the oscillation stabilization time from when reset is effected or STOP mode is released to when oscillation is stabilized. OSTS is set by an 8-bit memory manipulation instruction. RESET input sets OSTS to 04H. Thus, when releasing the STOP mode by RESET input, the time required to release is 217/fX. Figure 7-3. Format of Oscillation Stabilization Time Select Register (OSTS) Address: FFFAH After reset: 04H R/W Symbol 7 6 5 4 3 2 1 0 OSTS 0 0 0 0 0 OSTS2 OSTS1 OSTS0 OSTS2 OSTS1 OSTS0 Selection of oscillation stabilization time fX = 8.38 MHz fX = 12 MHzNote 0 0 0 212/fX 488 s 341 s 0 0 1 214/fX 1.95 ms 1.36 ms 0 1 0 215/fX 3.91 ms 2.73 ms 1 216/fX 7.82 ms 5.46 ms 0 217/fX 15.6 ms 10.9 ms 0 1 1 0 Other than the above Setting prohibited Note Expanded-specification products of PD780024A, 780034A Subseries only. Caution The wait time when STOP mode is released does not include the time ("a" in the figure below) from when STOP mode is released until the clock starts oscillation. This also applies when RESET is input and an interrupt request is generated. STOP mode is released Voltage waveform of X1 pin a Remark fX: Main system clock oscillation frequency 172 User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR 7.4 System Clock Oscillator 7.4.1 Main system clock oscillator The main system clock oscillator oscillates with a crystal resonator or a ceramic resonator (8.38 MHz TYP.) connected to the X1 and X2 pins. External clocks can be input to the main system clock oscillator. In this case, input a clock signal to the X1 pin and an inverted-phase clock signal to the X2 pin. Figure 7-4 shows an external circuit of the main system clock oscillator. Figure 7-4. External Circuit of Main System Clock Oscillator (a) Crystal and ceramic oscillation (b) External clock X2 X2 X1 VSS1 External clock X1 Crystal resonator or ceramic resonator Caution Do not execute the STOP instruction and do not set MCC (bit 7 of processor clock control register (PCC)) to 1 if an external clock is input. This is because when the STOP instruction is executed or MCC is set to 1, the main system clock operation stops and the X2 pin is connected to VDD1 via a pull-up resistor. User's Manual U14046EJ5V0UD 173 CHAPTER 7 CLOCK GENERATOR 7.4.2 Subsystem clock oscillator The subsystem clock oscillator oscillates with a crystal resonator (32.768 kHz TYP.) connected to the XT1 and XT2 pins. External clocks can be input to the subsystem clock oscillator. In this case, input a clock signal to the XT1 pin and an inverted-phase clock signal to the XT2 pin. Figure 7-5 shows an external circuit of the subsystem clock oscillator. Figure 7-5. External Circuit of Subsystem Clock Oscillator (a) Crystal oscillation (b) External clock XT2 XT2 32.768 kHz XT1 VSS1 External clock Cautions are listed on the next page. 174 User's Manual U14046EJ5V0UD XT1 CHAPTER 7 Caution CLOCK GENERATOR 1. When using the main system clock oscillator and subsystem clock oscillator, wire as follows in the area enclosed by broken lines in Figures 7-4 and 7-5 to avoid an adverse effect from wiring capacitance. * Keep the wiring length as short as possible. * Do not cross the wiring with other signal lines. Do not route the wiring near a signal line through which a high fluctuating current flows. * Always make the ground point of the oscillator capacitor the same potential as VSS1. Do not ground the capacitor to a ground pattern through which a high current flows. * Do not fetch signals from the oscillator. Note that the subsystem clock oscillator is designed as a low-amplitude circuit for reducing power consumption. Figure 7-6 shows examples of incorrect oscillator connection. Figure 7-6. Examples of Incorrect Oscillator Connection (1/2) (a) Too long wiring (b) Crossed signal line PORTn (n = 0 to 7) X2 X1 VSS1 X2 X1 VSS1 Remark When using the subsystem clock, replace X1 and X2 with XT1 and XT2, respectively. Also, insert resistors in series on the XT2 side. User's Manual U14046EJ5V0UD 175 CHAPTER 7 CLOCK GENERATOR Figure 7-6. Examples of Incorrect Oscillator Connection (2/2) (c) Wiring near high fluctuating current (d) Current flowing through ground line of oscillator (potential at points A, B, and C fluctuates) VDD0 Pnm X2 X1 VSS1 X1 VSS1 High current X2 A B C High current (e) Signals are fetched X2 X1 VSS1 Remark When using the subsystem clock, replace X1 and X2 with XT1 and XT2, respectively. Also, insert resistors in series on the XT2 side. Caution 2. When X2 and XT1 are wired in parallel, the crosstalk noise of X2 may increase with XT1, resulting in malfunction. To prevent that from occurring, it is recommended to wire X2 and XT1 so that they are not in parallel, and to connect the IC pin between X2 and XT1 directly to VSS1. 176 User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR 7.4.3 When subsystem clock is not used If it is not necessary to use the subsystem clock for low power consumption operations and watch operations, connect the XT1 and XT2 pins as follows. XT1: Connect directly to VDD0 or VDD1 XT2: Leave open In this state, however, some current may leak via the internal feedback resistor of the subsystem clock oscillator when the main system clock stops. To minimize leakage current, the above internal feedback resistor can be removed by setting bit 6 (FRC) of the processor clock control register (PCC). In this case also, connect the XT1 and XT2 pins as described above. Figure 7-7. Subsystem Clock Feedback Resistor FRC P-ch Feedback resistor XT1 XT2 Remark The feedback resistor is required to control the bias point of the oscillation waveform so that the bias point is in the middle of the power supply voltage. User's Manual U14046EJ5V0UD 177 CHAPTER 7 CLOCK GENERATOR 7.5 Clock Generator Operations The clock generator generates the following types of clocks and controls the CPU operating mode including the standby mode. * Main system clock * Subsystem clock * CPU clock fX fXT fCPU * Clock to peripheral hardware The following clock generator functions and operations are determined by the processor clock control register (PCC). (a) Upon generation of the RESET signal, the lowest speed mode of the main system clock (3.81 s @ 8.38 MHz operation) is selected (PCC = 04H). Main system clock oscillation stops while a low level is applied to the RESET pin. (b) With the main system clock selected, one of the five levels of minimum instruction execution time (0.166 s, 0.333 s, 0.666 s, 1.33 s, 2.66 s: @ 12 MHz operationNote, 0.238 s, 0.476 s, 0.954 s, 1.90 s, 3.81 s: @ 8.38 MHz operation) can be selected by setting PCC. (c) With the main system clock selected, two standby modes, the STOP and HALT modes, are available. To reduce power consumption in the STOP mode, the subsystem clock feedback resistor can be disconnected to stop the subsystem clock. (d) PCC can be used to select the subsystem clock and to operate the system with low power consumption (122 s @ 32.768 kHz operation). (e) With the subsystem clock selected, main system clock oscillation can be stopped via PCC. The HALT mode can be used. However, the STOP mode cannot be used. (Subsystem clock oscillation cannot be stopped.) (f) The main system clock is divided and supplied to the peripheral hardware. The subsystem clock is supplied to the watch timer and clock output functions only. Thus the watch function and the clock output function can also be continued in the standby state. However, since all other peripheral hardware operate with the main system clock, the peripheral hardware also stops if the main system clock is stopped (except external input clock operation). Note Expanded-specification products of PD780024A, 780034A Subseries only 178 User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR 7.5.1 Main system clock operations When operating with the main system clock (with bit 5 (CLS) of the processor clock control register (PCC) cleared to 0), the following operations are carried out by PCC setting. (a) Because the operation-guaranteed instruction execution speed depends on the power supply voltage, the minimum instruction execution time can be changed by bits 0 to 2 (PCC0 to PCC2) of PCC. (b) When bit 4 (CSS) of PCC is set to 1 when operating with the main system clock, if bit 7 (MCC) of PCC is set to 1 after the operation has been switched to the subsystem clock (CLS = 1), the main system clock oscillation stops (see Figure 7-8 (1)). (c) If bit 7 (MCC) of PCC is set to 1 when operating with the main system clock, the main system clock oscillation does not stop. When bit 4 (CSS) of PCC is set to 1 and the operation is switched to the subsystem clock (CLS = 1) after that, the main system clock oscillation stops (see Figure 7-8 (2)). Figure 7-8. Main System Clock Stop Function (1) Operation when MCC is set after setting CSS with main system clock operation MCC CSS CLS Main system clock oscillation Subsystem clock oscillation CPU clock (2) Operation when CSS is set after setting MCC with main system clock operation MCC CSS CLS Oscillation does not stop Main system clock oscillation Subsystem clock oscillation CPU clock User's Manual U14046EJ5V0UD 179 CHAPTER 7 CLOCK GENERATOR 7.5.2 Subsystem clock operations When operating with the subsystem clock (with bit 5 (CLS) of the processor clock control register (PCC) set to 1), the following operations are carried out. (a) The minimum instruction execution time remains constant (122 s @ 32.768 kHz operation) irrespective of bits 0 to 2 (PCC0 to PCC2) of PCC. (b) Watchdog timer counting stops. Caution Do not execute the STOP instruction while the subsystem clock is in operation. 7.6 Changing System Clock and CPU Clock Settings 7.6.1 Time required for switchover between system clock and CPU clock The system clock and CPU clock can be switched over by means of bits 0 to 2 (PCC0 to PCC2) and bit 4 (CSS) of the processor clock control register (PCC). The actual switchover operation is not performed directly after writing to the PCC; operation continues on the preswitchover clock for several instructions (see Table 7-3). Determination as to whether the system is operating on the main system clock or the subsystem clock is performed by bit 5 (CLS) of the PCC register. Table 7-3. Maximum Time Required for CPU Clock Switchover Set Value Before Switchover Set Value After Switchover CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 CSS PCC2 PCC1 PCC0 0 0 1 0 0 0 0 0 0 1 16 instructions 0 0 1 0 0 0 1 0 0 0 0 0 1 8 instructions 0 1 0 4 instructions 4 instructions 0 1 1 2 instructions 2 instructions 2 instructions 1 0 0 1 instruction 1 instruction 1 instruction 1 instruction x x x 1 instruction 1 instruction 1 instruction 1 instruction 1 0 1 0 0 1 x 16 instructions 16 instructions fX/2fXT instruction 8 instructions 8 instructions 8 instructions fX/4fXT instruction 4 instructions 4 instructions fX/8fXT instruction 2 instructions fX/16fXT instruction fX/32fXT instruction 1 instruction Selection of the CPU clock cycle division ratio (PCC0 to PCC2) and switchover from the main system clock to the subsystem clock (changing CSS from 0 to 1) should not be set simultaneously. Simultaneous setting is possible, however, for selection of the CPU clock cycle division ratio (PCC0 to PCC2) and switch over from the subsystem clock to the main system clock (changing CSS from 1 to 0). 180 x 16 instructions Remark One instruction is the minimum instruction execution time with the pre-switchover CPU clock. Caution x User's Manual U14046EJ5V0UD CHAPTER 7 CLOCK GENERATOR 7.6.2 System clock and CPU clock switching procedure This section describes procedure for switching between the system clock and CPU clock. Figure 7-9. System Clock and CPU Clock Switching VDD RESET Interrupt request signal System clock CPU clock fX Lowestspeed operation fX Highestspeed operation fXT Subsystem clock operation fX High-speed operation Wait (15.6 ms: @8.38 MHz operation) Internal reset operation <1> The CPU is reset by setting the RESET signal to low level after power-on. After that, when reset is released by setting the RESET signal to high level, the main system clock starts oscillation. At this time, the oscillation stabilization time (217/fX) is secured automatically. After that, the CPU starts executing instructions at the minimum speed of the main system clock (3.81 s @ 8.38 MHz operation). <2> After the lapse of sufficient time for the VDD voltage to increase to enable operation at maximum speeds, PCC is rewritten and maximum-speed operation is carried out. <3> Upon detection of a decrease of the VDD voltage due to an interrupt request signal, the main system clock is switched to the subsystem clock (which must be in an oscillation stable state). <4> Upon detection of VDD voltage reset due to an interrupt, 0 is set to the MCC and oscillation of the main system clock is started. After the lapse of the time required for stabilization of oscillation, PCC is rewritten and the maximum-speed operation is resumed. Caution When the main system clock is stopped and the device is operating on the subsystem clock, wait until the oscillation stabilization time has been secured by the program before switching back to the main system clock. User's Manual U14046EJ5V0UD 181 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.1 Functions of 16-Bit Timer/Event Counter 0 16-bit timer/event counter 0 has the following functions. (1) Interval timer 16-bit timer/event counter 0 generates interrupt requests at the preset time interval. * Number of counts: 2 to 65536 (2) External event counter 16-bit timer/event counter 0 can measure the number of pulses with a high-/low-level width of a signal input externally. * Valid level pulse width: 16/fX or more (3) Pulse width measurement 16-bit timer/event counter 0 can measure the pulse width of an externally input signal. * Valid level pulse width: 2/fX or more (4) Square-wave output 16-bit timer/event counter 0 can output a square wave with any selected frequency. * Cycle: (2 x 2 to 65536 x 2) x count clock cycle (5) PPG output 16-bit timer/event counter 0 can output a square wave that have arbitrary cycle and pulse width. * 2 < Pulse width < Cycle (FFFF + 1) H 182 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.2 Configuration of 16-Bit Timer/Event Counter 0 16-bit timer/event counter 0 consists of the following hardware. Table 8-1. Configuration of 16-Bit Timer/Event Counter 0 Item Configuration Timer counter 16-bit timer counter 0 (TM0) Register 16-bit timer capture/compare registers: 00, 01 (CR00, CR01) Timer input TI00, TI01 Timer output TO0 Control registers 16-bit timer mode control register 0 (TMC0) Capture/compare control register 0 (CRC0) 16-bit timer output control register 0 (TOC0) Prescaler mode register 0 (PRM0) Port mode register 7 (PM7) Port 7 (P7) Figure 8-1 shows block diagram of this counter. Figure 8-1. Block Diagram of 16-Bit Timer/Event Counter 0 Internal bus Capture/compare control register 0 (CRC0) TI01/P71 Selector Noise eliminator Selector CRC02 CRC01 CRC00 INTTM00 16-bit timer capture/compare register 00 (CR00) Match fX/23 Selector fX fX/22 fX/26 Noise eliminator 16-bit timer counter 0 (TM0) TO0/TI00/ P70Note Output controller Match 2 Output latch (P70) Noise eliminator PM70 16-bit timer capture/compare register 01 (CR01) Selector TI00/TO0/P70Note Clear INTTM01 CRC02 PRM01 PRM00 Prescaler mode register 0 (PRM0) TMC03 TMC02 OVF0 TOC04 LVS0 LVR0 TOC01 TOE0 16-bit timer mode 16-bit timer output control register 0 control register 0 (TMC0) (TOC0) Internal bus Note TI00 input and TO0 output cannot be used at the same time. User's Manual U14046EJ5V0UD 183 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (1) 16-bit timer counter 0 (TM0) TM0 is a 16-bit read-only register that counts count pulses. The counter is incremented in synchronization with the rising edge of the count clock. If the count value is read during operation, input of the count clock is temporarily stopped, and the count value at that point is read. The count value is reset to 0000H in the following cases. <1> At RESET input <2> If TMC03 and TMC02 are cleared <3> If the valid edge of TI00 is input in the clear & start mode entered by inputting the valid edge of TI00 <4> If TM0 and CR00 match in the clear & start mode entered on a match between TM0 and CR00 (2) 16-bit timer capture/compare register 00 (CR00) CR00 is a 16-bit register which has the functions of both a capture register and a compare register. Whether it is used as a capture register or as a compare register is set by bit 0 (CRC00) of capture/compare control register 0 (CRC0). * When CR00 is used as a compare register The value set in CR00 is constantly compared with the 16-bit timer counter 0 (TM0) count value, and an interrupt request (INTTM00) is generated if they match. It can also be used as the register that holds the interval time then TM0 is set to interval timer operation. * When CR00 is used as a capture register It is possible to select the valid edge of the TI00 pin or the TI01 pin as the capture trigger. Setting of the TI00 or TI01 valid edge is performed by means of prescaler mode register 0 (PRM0) (see Table 8-2). Table 8-2. CR00 Capture Trigger and Valid Edges of TI00 and TI01 Pins (1) TI00 pin valid edge selected as capture trigger (CRC01 = 1, CRC00 = 1) CR00 Capture Trigger TI00 Pin Valid Edge ES01 ES00 Falling edge Rising edge 0 1 Rising edge Falling edge 0 0 No capture operation Both rising and falling edges 1 1 (2) TI01 pin valid edge selected as capture trigger (CRC01 = 0, CRC00 = 1) CR00 Capture Trigger TI01 Pin Valid Edge ES11 ES10 Falling edge Falling edge 0 0 Rising edge Rising edge 0 1 Both rising and falling edges Both rising and falling edges 1 1 Remarks 1. Setting ES01, ES00 = 1, 0 and ES11, ES10 = 1, 0 is prohibited. 2. ES01, ES00: Bits 5 and 4 of prescaler mode register 0 (PRM0) ES11, ES10: Bits 7 and 6 of prescaler mode register 0 (PRM0) CRC01, CRC00: Bits 1 and 0 of capture/compare control register 0 (CRC0) 184 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 CR00 is set by a 16-bit memory manipulation instruction. RESET input makes CR00 undefined. Cautions 1. Set CR00 to a value other than 0000H in the clear & start mode entered on a match between TM0 and CR00. However, in the free-running mode and in the clear mode using the valid edge of TI00, if CR00 is cleared to 0000H, an interrupt request (INTTM00) is generated when CR00 changes from 0000H to 0001H following overflow (FFFFH). 2. If the new value of CR00 is less than the value of 16-bit timer counter 0 (TM0), TM0 continues counting, overflows, and then starts counting from 0 again. If the new value of CR00 is less than the old value, therefore, the timer must be reset to be restarted after the value of CR00 is changed. 3. When P70 is used as the input pin for the valid edge of TI00, it cannot be used as a timer output (TO0). Moreover, when P70 is used as TO0, it cannot be used as the input pin for the valid edge of TI00. (3) 16-bit timer capture/compare register 01 (CR01) CR01 is a 16-bit register which has the functions of both a capture register and a compare register. Whether it is used as a capture register or a compare register is set by bit 2 (CRC02) of capture/compare control register 0 (CRC0). * When CR01 is used as a compare register The value set in CR01 is constantly compared with the 16-bit timer counter 0 (TM0) count value, and an interrupt request (INTTM01) is generated if they match. * When CR01 is used as a capture register It is possible to select the valid edge of the TI00 pin as the capture trigger. The TI00 valid edge is set by means of prescaler mode register 0 (PRM0) (see Table 8-3). Table 8-3. CR01 Capture Trigger and Valid Edge of TI00 Pin (CRC02 = 1) CR01 Capture Trigger TI00 Pin Valid Edge ES01 ES00 Falling edge Falling edge 0 0 Rising edge Rising edge 0 1 Both rising and falling edges Both rising and falling edges 1 1 Remarks 1. Setting ES01, ES00 = 1, 0 is prohibited. 2. ES01, ES00: Bits 5 and 4 of prescaler mode register 0 (PRM0) CRC02: Bit 2 of capture/compare control register 0 (CRC0) User's Manual U14046EJ5V0UD 185 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 CR01 is set by a 16-bit memory manipulation instruction. RESET input makes CR01 undefined. Caution Set CR01 to other than 0000H in the clear & start mode entered on a match between TM0 and CR00. However, in the free-running mode and in the clear mode using the valid edge of TI00, if CR01 is cleared to 0000H, an interrupt request (INTTM01) is generated when CR01 changes from 0000H to 0001H following overflow (FFFFH). 8.3 Registers to Control 16-Bit Timer/Event Counter 0 The following six types of registers are used to control 16-bit timer/event counter 0. * 16-bit timer mode control register 0 (TMC0) * Capture/compare control register 0 (CRC0) * 16-bit timer output control register 0 (TOC0) * Prescaler mode register 0 (PRM0) * Port mode register 7 (PM7) * Port 7 (P7) (1) 16-bit timer mode control register 0 (TMC0) This register sets the 16-bit timer operating mode, the 16-bit timer counter 0 (TM0) clear mode, and output timing, and detects an overflow. TMC0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears TMC0 to 00H. Caution 16-bit timer counter 0 (TM0) starts operation at the moment TMC02 and TMC03 (operation stop mode) are set to a value other than 0, 0, respectively. Clear TMC02 and TMC03 to 0, 0 to stop the operation. 186 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-2. Format of 16-Bit Timer Mode Control Register 0 (TMC0) Address: FF60H After reset: 00H Symbol 7 6 5 4 TMC0 0 0 0 0 TMC03 TMC02 0 0 R/W <3> <2> TMC03 TMC02 1 <0> 0 OVF0 Operating mode and clear mode selection Operation stop TO0 output timing selection Interrupt request generation No change Not generated Match between TM0 and CR00 or match between TM0 and CR01 Generated on match between TM0 and CR00, or match between TM0 and CR01 (TM0 cleared to 0) 0 1 Free-running mode 1 0 Clear & start on TI00 valid edgeNote 1 1 1 Clear & start on match between TM0 and CR00Note 2 OVF0 - Match between TM0 and CR00 or match between TM0 and CR01 Overflow detection of 16-bit timer counter 0 (TM0) 0 Overflow not detected 1 Overflow detected Notes 1. Set the valid edge of the TI00/TO0/P70 pin with prescaler mode register 0 (PRM0). 2. If the clear & start mode entered on a match between TM0 and CR00 is selected, when the set value of CR00 is FFFFH and the TM0 value changes from FFFFH to 0000H, the OVF0 flag is set to 1. Cautions 1. To write different data to TMC0, stop the timer operation before writing. 2. The timer operation must be stopped before writing to bits other than the OVF0 flag. Remarks 1. TO0: 16-bit timer/event counter 0 output pin 2. TI00: 16-bit timer/event counter 0 input pin 3. TM0: 16-bit timer counter 0 4. CR00: 16-bit timer capture/compare register 00 5. CR01: 16-bit timer capture/compare register 01 User's Manual U14046EJ5V0UD 187 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (2) Capture/compare control register 0 (CRC0) This register controls the operation of the 16-bit timer capture/compare registers (CR00, CR01). CRC0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears CRC0 to 00H. Figure 8-3. Format of Capture/Compare Control Register 0 (CRC0) Address: FF62H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 CRC0 0 0 0 0 0 CRC02 CRC01 CRC00 CRC02 CR01 operating mode selection 0 Operate as compare register 1 Operate as capture register CRC01 CR00 capture trigger selection 0 Capture on valid edge of TI01 1 Capture on valid edge of TI00 by reverse phaseNote CRC00 CR00 operating mode selection 0 Operate as compare register 1 Operate as capture register Note If both the rising and falling edges have been selected as the valid edges of TI00, capture is not performed. Cautions 1. The timer operation must be stopped before setting CRC0. 2. When the clear & start mode entered on a match between TM0 and CR00 is selected by 16bit timer mode control register 0 (TMC0), CR00 should not be specified as a capture register. 3. To ensure the reliability of the capture operation, the capture trigger requires a pulse longer than two cycles of the count clock selected by prescaler mode register 0 (PRM0) (see Figure 8-31). 188 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (3) 16-bit timer output control register 0 (TOC0) This register controls the operation of the 16-bit timer/event counter output controller. It sets R-S type flip-flop (LV0) set/reset, output inversion enable/disable, and 16-bit timer/event counter timer output enable/disable. TOC0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears TOC0 to 00H. Figure 8-4. Format of 16-Bit Timer Output Control Register 0 (TOC0) Address: FF63H After reset: 00H R/W Symbol 7 6 5 4 <3> <2> 1 <0> TOC0 0 0 0 TOC04 LVS0 LVR0 TOC01 TOE0 TOC04 Timer output F/F control by match of CR01 and TM0 0 Inversion operation disabled 1 Inversion operation enabled LVS0 LVR0 16-bit timer/event counter 0 timer output F/F status setting 0 0 No change 0 1 Timer output F/F reset (0) 1 0 Timer output F/F set (1) 1 1 Setting prohibited TOC01 Timer output F/F control by match of CR00 and TM0 0 Inversion operation disabled 1 Inversion operation enabled TOE0 16-bit timer/event counter 0 output control 0 Output disabled (output set to level 0) 1 Output enabled Cautions 1. The timer operation must be stopped before setting TOC0. 2. If LVS0 and LVR0 are read after data is set, they will be 0. 3. Be sure to clear bits 5 to 7 of TOC0 to 0. User's Manual U14046EJ5V0UD 189 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (4) Prescaler mode register 0 (PRM0) This register is used to set the 16-bit timer counter 0 (TM0) count clock and TI00, TI01 input valid edges. PRM0 is set by an 8-bit memory manipulation instruction. RESET input clears PRM0 to 00H. Figure 8-5. Format of Prescaler Mode Register 0 (PRM0) Address: FF61H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 PRM0 ES11 ES10 ES01 ES00 0 0 PRM01 PRM00 ES11 ES10 0 0 Falling edge 0 1 Rising edge 1 0 Setting prohibited 1 1 Both falling and rising edges ES01 ES00 0 0 Falling edge 0 1 Rising edge 1 0 Setting prohibited 1 1 Both falling and rising edges PRM01 PRM00 TI01 valid edge selection TI00 valid edge selection Count clock selection fX = 8.38 MHz fX = 12 MHzNote 1 0 0 fX 8.38 MHz 12 MHz 0 1 fX/22 2.09 MHz 3 MHz 1 0 fX/26 130 kHz 187 kHz 1 1 TI00 valid edgeNotes 2, 3 Notes 1. Expanded-specification products of PD780024A, 780034A Subseries only. 2. The external clock requires a pulse longer than two cycles of the internal count clock (fX/23). 3. When the valid edge of TI00 is selected, the main system clock is used as the sampling clock for noise elimination. The valid edge of TI00 can be used only when the main system clock is operating. Cautions 1. Always set data to PRM0 after stopping the timer operation. 2. If the valid edge of TI00 is to be set as the count clock, do not set the clear & start mode and the capture trigger at the valid edge of TI00. Moreover, do not use the P70/TI00/TO0 pin as a timer output (TO0). 3. If the TI00 or TI01 pin is high level immediately after system reset, the rising edge is immediately detected after the rising edge or both the rising and falling edges are set as the valid edge(s) of the TI00 pin or TI01 pin to enable the operation of 16-bit timer counter 0 (TM0). Be careful when pulling up the TI00 pin or the TI01 pin. However, when re-enabling operation after the operation has been stopped once, the rising edge is not detected. Remarks 1. fX: Main system clock oscillation frequency 2. TI00, TI01: 16-bit timer/event counter 0 input pin 190 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (5) Port mode register 7 (PM7) This register sets port 7 input/output in 1-bit units. When using the P70/TO0/TI00 pin for timer output, clear PM70 and the output latch of P70 to 0. When using the P70/TO0/TI00 pin for timer input, set PM70 to 1. At this time, the output latch of P70 can be either 0 or 1. PM7 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM7 to FFH. Figure 8-6. Format of Port Mode Register 7 (PM7) Address: FF27H After reset: FFH Symbol 7 6 PM7 1 1 PM7n 5 4 R/W 3 2 1 0 PM75 PM74 PM73 PM72 PM71 PM70 P7n pin I/O mode selection (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD 191 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.4 Operation of 16-Bit Timer/Event Counter 0 8.4.1 Interval timer operation Setting 16-bit timer mode control register 0 (TMC0) and capture/compare control register 0 (CRC0) as shown in Figure 8-7 allows operation as an interval timer. Interrupt requests are generated repeatedly using the count value set in 16-bit timer capture/compare register 00 (CR00) beforehand as the interval. When the count value of 16-bit timer counter 0 (TM0) matches the value set to CR00, counting continues with the TM0 value cleared to 0 and the interrupt request signal (INTTM00) is generated. The count clock of the 16-bit timer/event counter can be selected using bits 0 and 1 (PRM00, PRM01) of prescaler mode register 0 (PRM0). Figure 8-7. Control Register Settings for Interval Timer Operation (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 1 1 OVF0 0 0 Clears and starts on match between TM0 and CR00. (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 0/1 0/1 0 CR00 used as compare register 192 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-8. Interval Timer Configuration Diagram 16-bit timer capture/compare register 00 INTTM00 Selector fX fX/22 fX/26 TI00/TO0/P70 OVF0Note 16-bit timer counter 0 Noise eliminator Clear circuit fX/23 Note OVF0 is 1 only when 16-bit timer capture/compare register 00 is set to FFFFH. Figure 8-9. Timing of Interval Timer Operation t Count clock TM0 count value 0000H 0001H Count start CR00 N N 0000H 0001H Clear N 0000H 0001H N Clear N N N INTTM00 Interrupt acknowledged Interrupt acknowledged TO0 Interval time Interval time Remark Interval time = (N + 1) x t N = 0001H to FFFFH User's Manual U14046EJ5V0UD 193 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 When the compare register is changed during timer count operation, if the value after 16-bit timer capture/ compare register 00 (CR00) is changed is smaller than that of 16-bit timer counter 0 (TM0), TM0 continues counting, overflows and then restarts counting from 0. Thus, if the value (M) after the CR00 change is smaller than that (N) before the change, it is necessary to restart the timer after changing CR00. Figure 8-10. Timing After Change of Compare Register During Timer Count Operation Count clock N CR00 TM0 count value X-1 M X FFFFH Remark N > X > M 194 User's Manual U14046EJ5V0UD 0000H 0001H 0002H CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.4.2 External event counter operation The external event counter counts the number of external clock pulses to be input to the TI00 pin with using 16bit timer counter 0 (TM0). TM0 is incremented each time the valid edge specified by prescaler mode register 0 (PRM0) is input. When the TM0 count value matches the 16-bit timer capture/compare register 00 (CR00) value, TM0 is cleared to 0 and the interrupt request signal (INTTM00) is generated. Input a value other than 0000H to CR00. (A count operation with a pulse cannot be carried out.) The rising edge, the falling edge, or both edges can be selected using bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0). Because an operation is carried out only when the valid edge of the TI00 pin is detected twice after sampling with the internal clock (fX/23), noise with a short pulse width can be removed. Caution When used as an external event counter, the P70/TI00/TO0 pin cannot be used as a timer output (TO0). Figure 8-11. Control Register Settings in External Event Counter Mode (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 1 1 OVF0 0 0 Clears and starts on match between TM0 and CR00. (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 0/1 0/1 0 CR00 used as compare register User's Manual U14046EJ5V0UD 195 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-12. External Event Counter Configuration Diagram Internal bus 16-bit timer capture/compare register 00 Match INTTM00 Clear fX/23 Noise eliminator 16-bit timer counter 0 (TM0) OVF0Note Valid edge of TI00 Note OVF0 is 1 only when 16-bit timer capture/compare register 00 is set to FFFFH. Figure 8-13. External Event Counter Operation Timing (with Rising Edge Specified) TI00 pin input TM0 count value CR00 0000H 0001H 0002H 0003H 0004H 0005H N-1 N 0000H 0001H 0002H 0003H N INTTM00 Caution 196 When reading the external event counter count value, TM0 should be read. User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.4.3 Pulse width measurement operations It is possible to measure the pulse width of the signals input to the TI00 pin and TI01 pin using 16-bit timer counter 0 (TM0). There are two measurement methods: measuring with TM0 used in free-running mode, and measuring by restarting the timer in synchronization with the edge of the signal input to the TI00 pin. (1) Pulse width measurement with free-running counter and one capture register When 16-bit timer counter 0 (TM0) is operated in free-running mode (see register settings in Figure 8-14), and the edge specified by prescaler mode register 0 (PRM0) is input to the TI00 pin, the value of TM0 is taken into 16-bit timer capture/compare register 01 (CR01) and an external interrupt request signal (INTTM01) is set. Any of three edges can be selected--rising, falling, or both edges--specified by bits 4 and 5 (ES00 and ES01) of PRM0. Sampling is performed with the count clock selected by PRM0, and a capture operation is only performed when a valid level of the TI00 pin is detected twice, thus eliminating noise with a short pulse width. Figure 8-14. Control Register Settings for Pulse Width Measurement with Free-Running Counter and One Capture Register (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 0 1 OVF0 0 0 Free-running mode (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 1 0/1 0 CR00 used as compare register CR01 used as capture register User's Manual U14046EJ5V0UD 197 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-15. Configuration Diagram for Pulse Width Measurement with Free-Running Counter fX/22 fX/2 6 Selector fX 16-bit timer counter 0 OVF0 16-bit timer capture/compare register 01 TI00/TO0/P70 INTTM01 Internal bus Figure 8-16. Timing of Pulse Width Measurement Operation with Free-Running Counter and One Capture Register (with Both Edges Specified) t Count clock TM0 count value 0000H 0001H D0 D0 + 1 D1 D1 + 1 FFFFH 0000H D2 D3 TI00 pin input CR01 capture value D0 D1 D2 D3 INTTM01 Note OVF0 (D1 - D0) x t (10000H - D1 + D2) x t Note OVF0 must be cleared by software. 198 User's Manual U14046EJ5V0UD (D3 - D2) x t CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (2) Measurement of two pulse widths with free-running counter When 16-bit timer counter 0 (TM0) is operated in free-running mode (see register settings in Figure 8-17), it is possible to simultaneously measure the pulse widths of the two signals input to the TI00 pin and the TI01 pin. When the edge specified by bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0) is input to the TI00 pin, the value of TM0 is taken into 16-bit timer capture/compare register 01 (CR01) and an interrupt request signal (INTTM01) is set. Also, when the edge specified by bits 6 and 7 (ES10 and ES11) of PRM0 is input to the TI01 pin, the value of TM0 is taken into 16-bit timer capture/compare register 00 (CR00) and an interrupt request signal (INTTM00) is set. Any of three edges can be selected--rising, falling, or both edges--as the valid edges for the TI00 pin and the TI01 pin specified by bits 4 and 5 (ES00 and ES01) and bits 6 and 7 (ES10 and ES11) of PRM0, respectively. Sampling is performed at the interval selected by prescaler mode register 0 (PRM0), and a capture operation is only performed when a valid level of the TI00 pin or TI01 pin is detected twice, thus eliminating noise with a short pulse width. Figure 8-17. Control Register Settings for Measurement of Two Pulse Widths with Free-Running Counter (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 0 1 OVF0 0 0 Free-running mode (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 1 0 1 CR00 used as capture register Captures valid edge of TI01 pin to CR00 CR01 used as capture register User's Manual U14046EJ5V0UD 199 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-18. Timing of Pulse Width Measurement Operation with Free-Running Counter (with Both Edges Specified) t Count clock TM0 count value 0000H 0001H D0 D0 + 1 D1 D1 + 1 FFFFH 0000H D2 D2 + 1 D2 + 2 D3 TI00 pin input CR01 capture value D0 D1 D2 INTTM01 TI01 pin input CR00 capture value D1 D2 + 1 INTTM00 Note OVF0 (D1 - D0) x t (10000H - D1 + D2) x t (10000H - D1 + (D2 + 1)) x t Note OVF0 must be cleared by software. 200 User's Manual U14046EJ5V0UD (D3 - D2) x t CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (3) Pulse width measurement with free-running counter and two capture registers When 16-bit timer counter 0 (TM0) is operated in free-running mode (see register settings in Figure 8-19), it is possible to measure the pulse width of the signal input to the TI00 pin. When the edge specified by bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0) is input to the TI00 pin, the value of TM0 is taken into 16-bit timer capture/compare register 01 (CR01) and an interrupt request signal (INTTM01) is set. Also, when the inverse edge to that of the capture operation to CR01 is input, the value of TM0 is taken into 16bit timer capture/compare register 00 (CR00). Either of two edges can be selected--rising or falling--as the valid edges for the TI00 pin specified by bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0). Sampling is performed at the interval selected by prescaler mode register 0 (PRM0), and a capture operation is only performed when a valid level of the TI00 pin is detected twice, thus eliminating noise with a short pulse width. Caution If the valid edge of TI00 is specified to be both the rising and falling edges, 16-bit timer capture/ compare register 00 (CR00) cannot perform the capture operation. Figure 8-19. Control Register Settings for Pulse Width Measurement with Free-Running Counter and Two Capture Registers (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 0 1 OVF0 0 0 Free-running mode (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 1 1 1 CR00 used as capture register Captures to CR00 at edge reverse to valid edge of TI00. CR01 used as capture register User's Manual U14046EJ5V0UD 201 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-20. Timing of Pulse Width Measurement Operation with Free-Running Counter and Two Capture Registers (with Rising Edge Specified) t Count clock TM0 count value 0000H 0001H D0 D0 + 1 D1 D1 + 1 FFFFH 0000H D2 D2 + 1 D3 TI00 pin input CR01 capture value D0 CR00 capture value D2 D1 D3 INTTM01 Note OVF0 (D1 - D0) x t (10000H - D1 + D2) x t (D3 - D2) x t Note OVF0 must be cleared by software. (4) Pulse width measurement by means of restart When input of a valid edge to the TI00 pin is detected, the count value of 16-bit timer counter 0 (TM0) is taken into 16-bit timer capture/compare register 01 (CR01), and then the pulse width of the signal input to the TI00 pin is measured by clearing TM0 and restarting the count (see register settings in Figure 8-22). The edge specification can be selected from two types, rising or falling edges, by bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0). Sampling is performed at the interval selected by prescaler mode register 0 (PRM0) and a capture operation is only performed when a valid level of the TI00 pin is detected twice, thus eliminating noise with a short pulse width. Caution If the valid edge of TI00 is specified to be both the rising and falling edges, 16-bit timer capture/ compare register 00 (CR00) cannot perform the capture operation. 202 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-21. Control Register Settings for Pulse Width Measurement by Means of Restart (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 1 OVF0 0 0 0 Clears and starts at valid edge of TI00 pin. (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 1 1 1 CR00 used as capture register Captures to CR00 at edge reverse to valid edge of TI00. CR01 used as capture register Figure 8-22. Timing of Pulse Width Measurement Operation by Means of Restart (with Rising Edge Specified) t Count clock TM0 count value 0000H 0001H D0 0000H 0001H D1 D2 0000H 0001H TI00 pin input CR01 capture value D0 D2 D1 CR00 capture value INTTM01 D1 x t D2 x t User's Manual U14046EJ5V0UD 203 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.4.4 Square-wave output operation A square wave with any selected frequency can be output at intervals determined by the count value preset to 16-bit timer capture/compare register 00 (CR00). The TO0 pin output status is reversed at intervals determined by the count value preset to CR00 by setting bit 0 (TOE0) and bit 1 (TOC01) of 16-bit timer output control register 0 (TOC0) to 1. This enables a square wave with any selected frequency to be output. Figure 8-23. Control Register Settings in Square-Wave Output Mode (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 1 1 OVF0 0 0 Clears and starts on match between TM0 and CR00. (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 0/1 0/1 0 CR00 used as compare register (c) 16-bit timer output control register 0 (TOC0) TOC04 LVS0 LVR0 TOC01 TOE0 TOC0 0 0 0 0 0/1 0/1 1 1 Enables TO0 output. Reverses output on match between TM0 and CR00. Specifies initial value of TO0 output F/F. Does not reverse output on match between TM0 and CR01. Figure 8-24. Square-Wave Output Operation Timing Count clock TM0 count value CR00 0000H 0001H 0002H N-1 N 0000H 0001H 0002H N INTTM00 TO0 pin output 204 User's Manual U14046EJ5V0UD N-1 N 0000H CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.4.5 PPG output operation Setting 16-bit timer mode control register 0 (TMC0) and capture/compare control register 0 (CRC0) as shown in Figure 8-25 allows operation as PPG (Programmable Pulse Generator) output. In the PPG output operation, square waves are output from the TO0 pin with the pulse width and the cycle that correspond to the count values set beforehand in 16-bit timer capture/compare register 01 (CR01) and in 16-bit timer capture/compare register 00 (CR00), respectively. Figure 8-25. Control Register Settings for PPG Output Operation (a) 16-bit timer mode control register 0 (TMC0) TMC03 TMC02 TMC0 0 0 0 0 1 1 OVF0 0 0 Clears and starts on match between TM0 and CR00. (b) Capture/compare control register 0 (CRC0) CRC02 CRC01 CRC00 CRC0 0 0 0 0 0 0 x 0 CR00 used as compare register CR01 used as compare register (c) 16-bit timer output control register 0 (TOC0) TOC04 LVS0 TOC0 0 0 0 1 0/1 LVR0 TOC01 TOE0 0/1 1 1 Enables TO0 output Reverses output on match between TM0 and CR00 Specifies initial value of TO0 output F/F Reverse output on match between TM0 and CR01 Cautions 1. CR00 and CR01 values in the following range should be set to: 0000H < CR01 < CR00 FFFFH 2. The cycle of the pulse generated via PPG output (CR00 setting value + 1) has a duty of (CR01 setting value + 1)/(CR00 setting value + 1). Remark x: Don't care User's Manual U14046EJ5V0UD 205 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Figure 8-26. PPG Output Configuration Diagram fX/22 fX/26 Clear circuit 16-bit timer counter 0 Output controller fX Selector 16-bit timer capture/ compare register 00 16-bit timer capture/compare register 01 Figure 8-27. PPG Output Operation Timing t Count clock TM0 count value 0000H 0001H M-1 M N-1 Count start 0000H 0001H Clear CR00 N CR01 M TO0 Pulse width: (M + 1) x t One cycle: (N + 1) x t Remark 0000H < M < N FFFFH 206 N User's Manual U14046EJ5V0UD TO0/TI00/P70 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5 Program List Caution The following sample program is shown as an example to describe the operation of semiconductor products and their applications. Therefore, when applying the following information to your devices, design the devices after performing evaluation under your own responsibility. User's Manual U14046EJ5V0UD 207 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5.1 Interval timer /*******************************************************************************/ /* */ /* Setting example of timer 0 interval timer mode */ /* Cycle set to 130 as intervalTM0 (at 8.38 MHz for 1 ms) */ /* Variable ppgdata prepared as rewrite data area */ /* : Cycle (if 0000, no change) */ /* ppgdata to be checked at every INTTM00, and changed if required. */ /* Therefore, if change is required, set the change data in ppgdata. */ /* When changed, ppgdata cleared to 0000. */ /* */ /*******************************************************************************/ #pragma sfr #pragma EI #pragma DI #define intervalTM0 130 /* Cycle data to be set to CR00 */ #pragma interrupt INTTM00 intervalint rb2 unsigned int ppgdata; /* Data area to be set to timer 0 */ void main(void) { PCC = 0x0; ppgdata = 0; P7 = 0b11111110; PM7.0 = 0; TMMK00 = 0; PRM0 = CRC0 = CR00 = TOC0 = TMC0 = EI(); 0b00000010; 0b00000000; intervalTM0; 0b00000111; 0b00001100; while(1); /* Set high-speed operation mode */ /* /* /* /* /* /* /* /* /* /* /* /* Set port */ Set the following to output */ Clear P70 */ Set P70 as output */ Set interrupt */ Cancel INTTM00 interrupt mask */ Set timer 0 */ Count clock is fx/2^6 */ Set CR00 and CR01 to compare register */ Set cycle initial value to CR00 */ Invert on match with CR00, initial value L */ Clear & start on match between TM0 and CR00 */ /* Loop as dummy here */ } /* Timer 0 interrupt function */ void intervalint() { unsigned int work; /***************************************************/ /* */ /* Define variables required for interrupt here */ /* */ /***************************************************/ work = ppgdata; if (work != 0) { CR00 = work; ppgdata = 0; if (work == 0xffff) { TMC0 = 0b00000000; /* Stop timer */ } } /***********************************************************/ /* */ /* Describe processing required for interrupt below */ /* */ /***********************************************************/ } 208 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5.2 Pulse width measurement by free-running counter and one capture register /******************************************************************************/ /* */ /* Timer 0 operation sample */ /* Pulse width measurement example by free-running and CR01 */ /* Measurement results to be up to 16 bits and not checked for errors */ /* data[0]: End flag */ /* data[1]: Measurement results (pulse width) */ /* data[2]: Previous read value */ /* */ /******************************************************************************/ #pragma sfr #pragma EI #pragma DI #pragma interrupt INTTM01 intervalint rb2 unsigned int data[3]; /* Data area */ void main(void) { unsigned int length; PCC = 0x0; data[0] = 0; data[1] = 0; data[2] = 0; /* Set high-speed operation mode */ PM7.0 = 1; TMMK01 = 0; PRM0 = 0b00110010; CRC0 = 0b00000100; TMC0 = 0b00000100; EI(); while(1){ while(data[0] == 0); DI(); length = data[1]; data[0] = 0; EI(); } /* /* /* /* /* /* /* /* /* Set port */ Set P70 as input */ Set interrupt */ Cancel INTTM01 interrupt mask */ Set timer 0 */ Both rising and falling edges for TI00 */ Count clock is fx/2^6 */ Set CR01 to capture register */ Start in free-run mode */ /* /* /* /* /* /* Dummy loop */ Wait for measurement completion */ Prohibit interrupt for exclusive operation */ Read measurement results */ Clear end flag */ Exclusive operation completed */ } /* Timer 0 interrupt function */ void intervalint() { unsigned int work; /*****************************************************/ /* */ /* Define variables required for interrupt here */ /* */ /*****************************************************/ work = CR01; /* Read capture value */ data[1] = work - data[2]; /* Calculate and update interval */ data[2] = work; /* Update read value */ data[0] = 0xffff; /* Set measurement completion flag */ /***********************************************************/ /* */ /* Describe processing required for interrupt below */ /* */ /***********************************************************/ } User's Manual U14046EJ5V0UD 209 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5.3 Two pulse widths measurement by free-running counter /******************************************************************************/ /* */ /* Timer 0 operation sample */ /* Two-pulse-width measurement sample by free-running */ /* Measurement results to be up to 16 bits and not checked for errors */ /* Result area at TI00 side */ /* data[0]: End flag */ /* data[1]: Measurement results (pulse width) */ /* data[2]: Previous read value */ /* Result area at TI01 side */ /* data[3]: End flag */ /* data[4]: Measurement results (pulse width) */ /* data[5]: Previous read value */ /* */ /******************************************************************************/ #pragma sfr #pragma EI #pragma DI #pragma interrupt INTTM00 intervalint rb2 #pragma interrupt INTTM01 intervalint2 rb2 unsigned int data[6]; /* Data area */ void main(void) { unsigned int length,length2; PCC = 0x0; data[0] = 0; data[1] = 0; data[2] = 0; data[3] = 0; data[4] = 0; data[5] = 0; PM7.0 = 1; PM7.1 = 1; TMMK01 = 0; TMMK00 = 0; PRM0 = 0b11110010; CRC0 = 0b00000101; TMC0 = 0b00000100; EI(); while(1){ if(data[0] != 0) { TMMK01 = 1; /* Set high-speed operation mode */ /* Clear data area */ /* /* /* /* /* /* /* /* /* /* /* /* Dummy loop */ /* TI00 measurement completion check */ length = data[1]; data[0] = 0; TMMK01 = 0; } if(data[3] != 0) { TMMK00 = 1; Set port */ Set P70 as input */ Set P71 as input */ Set interrupt */ Cancel INTTM01 interrupt mask */ Cancel INTTM00 interrupt mask */ Set timer 0 */ Both rising and falling edges */ Count clock is fx/2^6 */ Set CR00 and CR01 to capture register */ Start in free-run mode */ /* INTTM01 interrupt prohibited for exclusive operation */ /* Read measurement results */ /* Clear end flag */ /* Exclusive operation completed */ /* TI01 measurement completion check */ length2 = data[4]; data[3] = 0; TMMK00 = 0; /* INTTM00 interrupt prohibited for exclusive operation */ /* Read measurement results */ /* Clear end flag */ /* Exclusive operation completed */ } } } 210 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 /* INTTM00 interrupt function */ void intervalint() { unsigned int work; /******************************************************/ /* */ /* Define variables required for interrupt here */ /* */ /******************************************************/ work = CR00; /* Read capture value */ data[4] = work - data[5]; /* Calculate and update interval */ data[5] = work; /* Update read value */ data[3] = 0xffff; /* Set measurement completion flag */ /********************************************************/ /* */ /* Describe processing required for interrupt below */ /* */ /********************************************************/ } /* INTTM01 interrupt function */ void intervalint2() { unsigned int work; /******************************************************/ /* */ /* Define variables required for interrupt here */ /* */ /******************************************************/ work = CR01; /* Read capture value */ data[1] = work - data[2]; /* Calculate and update interval */ data[2] = work; /* Update read value */ data[0] = 0xffff; /* Set measurement completion flag */ /********************************************************/ /* */ /* Describe processing required for interrupt below */ /* */ /********************************************************/ } User's Manual U14046EJ5V0UD 211 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5.4 Pulse width measurement by restart /**************************************************************************/ /* */ /* Timer 0 operation sample */ /* Pulse width measurement example by restart */ /* Measurement results up to 16 bits, not to be checked for errors */ /* data[0]: End flag */ /* data[1]: Measurement results (pulse width) */ /* data[2]: Previous read value */ /* */ /**************************************************************************/ #pragma sfr #pragma EI #pragma DI #pragma interrupt INTTM01 intervalint rb2 unsigned int data[3]; /* Data area */ void main(void) { unsigned int length; PCC = 0x0; data[0] = 0; data[1] = 0; data[2] = 0; /* Set high-speed operation mode */ PM7.0 = 1; TMMK01 = 0; PRM0 = 0b00110010; CRC0 = 0b00000100; TMC0 = 0b00001000; EI(); while(1){ if(data[0] != 0) { TMMK01 = 1; /* /* /* /* /* /* /* /* /* Set port */ Set P70 as input */ Set interrupt */ Cancel INTTM01 interrupt mask */ Set timer 0 */ Both rising and falling edges */ Count clock is fx/2^6 */ Set CR01 to capture register */ Clear & start at TI00 valid edge */ /* Dummy loop */ /* Wait for TI00 measurement completion */ /* Prohibit INTTM01 interrupt for exclusive operation */ length = data[1]+data[2]; /* Cycle calculation based on measurement results */ data[0] = 0; /* Clear end flag */ TMMK01 = 0; /* Exclusive operation completed */ } } } /* Timer 0 interrupt function */ void intervalint() { /******************************************************/ /* */ /* Define variables required for interrupt here */ /* */ /******************************************************/ data[2] = data[1]; /* Update old data */ data[1] = CR01; /* Update read value */ data[0] = 0xffff; /* Set measurement completion flag */ /********************************************************/ /* */ /* Describe processing required for interrupt below */ /* */ /********************************************************/ } 212 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.5.5 PPG output /******************************************************************************/ /* */ /* Timer 0 PPG mode setting example */ /* Cycle set to 130 as intervalTM0 */ /* Active period set to 65 as active_time */ /* Array ppgdata prepared as data area for rewriting */ /* [0]: Active period (0000: no change, 0xffff: stop) */ /* [1]: Cycle (0000: no change) */ /* ppgdata to be checked at every INTTM00, and changed if required. */ /* Therefore, if change is required, set the change data in ppgdata. */ /* When changed, ppgdata cleared to 0000. */ /* */ /******************************************************************************/ #pragma sfr #pragma EI #pragma DI #define intervalTM0 130 /* Cycle data to be set to CR00 */ #define active_time 65 /* Initial value data of CR01 */ #pragma interrupt INTTM00 ppgint rb2 unsigned int ppgdata[2]; /* Data area to be set to timer 0 */ void main(void) { PCC = 0x0; ppgdata[0] = 0; ppgdata[1] = 0; P7 = 0b11111110; PM7.0 = 0; TMMK00 = 0; PRM0 CRC0 CR00 CR01 TOC0 = = = = = 0b00000010; 0b00000000; intervalTM0; active_time; 0b00010111; TMC0 = 0b00001100; EI(); /* Set high-speed operation mode */ /* /* /* /* /* /* /* /* /* /* /* Set port */ Clear P70 */ Set P70 to output */ Set interrupt */ Cancel INTTM00 interrupt mask */ Set timer 0 */ Count clock is fx/2^6 */ Set CR00 and CR01 to compare register */ Set initial value of cycle */ Set initial value of active period */ Inverted on match between CR00 and CR01, initial value L */ /* Clear & start on match between TM0 and CR00 */ while(1); } /* Timer 0 interrupt function */ void ppgint() { unsigned int work; work = ppgdata[0]; if (work != 0) { CR01 = work; ppgdata[0] = 0; if (work == 0xffff) { TMC0 = 0b00000000; } } work = ppgdata[1]; if (work != 0) { CR00 = work; ppgdata[1]=0; } } /* Stop timer */ User's Manual U14046EJ5V0UD 213 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 8.6 Cautions Related to 16-Bit Timer/Event Counter 0 (1) Timer start errors An error of up to one clock may occur in the time required for a match signal to be generated after timer start. This is because 16-bit timer counter 0 (TM0) is started asynchronously to the count clock. Figure 8-28. Start Timing of 16-Bit Timer Counter 0 (TM0) Count clock TM0 count value 0000H 0001H 0002H 0003H 0004H Timer start (2) 16-bit timer capture/compare register setting (clear & start mode entered on match between TM0 and CR00) Set 16-bit timer capture/compare registers 00, 01 (CR00, CR01) to other than 0000H. This means a 1-pulse count operation cannot be performed. (3) Capture register data retention timing If the valid edge of the TI00 pin is input during 16-bit timer capture/compare register 01 (CR01) read, CR01 performs a capture operation but, the read value at this time is not guaranteed. The interrupt request signal (INTTM01) is generated upon detection of the valid edge. Figure 8-29. Capture Register Data Retention Timing Count clock TM0 count N N+1 N+2 M M+1 M+2 Edge input INTTM01 Capture read signal CR01 capture value X N+1 Capture M+1 Read value not guaranteed though capture operation performed (4) Valid edge setting Set the valid edge of the TI00 pin after clearing bits 2 and 3 (TMC02 and TMC03) of 16-bit timer mode control register 0 (TMC0) to 0, 0, respectively, and then stopping the timer operation. The valid edge is set by bits 4 and 5 (ES00 and ES01) of prescaler mode register 0 (PRM0). 214 User's Manual U14046EJ5V0UD CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (5) Operation of OVF0 flag <1> The OVF0 flag is also set to 1 in the following case. Either of the clear & start mode entered on a match between TM0 and CR00, clear & start at the valid edge of TI00, or free-running mode is selected. CR00 is set to FFFFH. When TM0 is counted up from FFFFH to 0000H. Figure 8-30. Operation Timing of OVF0 Flag Count clock CR00 TM0 FFFFH FFFEH FFFFH 0000H 0001H OVF0 INTTM00 <2> Even if the OVF0 flag is cleared before the next count clock is counted (before TM0 becomes 0001H) after the occurrence of a TM0 overflow, the OVF0 flag is reset newly and clear is disabled. (6) Conflicting operations When the 16-bit timer capture/compare register (CR00/CR01) is used as a compare register, if the write period and the match timing of 16-bit timer counter 0 (TM0) conflict, match determination is not successfully done. Do not perform a write operation of CR00/CR01 near the match timing. (7) Timer operation <1> Even if 16-bit timer counter 0 (TM0) is read, the value is not captured by 16-bit timer capture/compare register 01 (CR01). <2> Regardless of the CPU's operation mode, when the timer stops, the signals input to pins TI00/TI01 are not acknowledged. User's Manual U14046EJ5V0UD 215 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 (8) Capture operation <1> If TI00 is specified as the valid edge of the count clock, a capture operation by the capture register specified as the trigger for TI00 is not possible. <2> If both the rising and falling edges are selected as the valid edges of TI00, capture is not performed. <3> To ensure the reliability of the capture operation, the capture trigger requires a pulse longer than two cycles of the count clock selected by prescaler mode register 0 (PRM0). Figure 8-31. CR01 Capture Operation with Rising Edge Specified Count clock TM0 N-3 N-2 N-1 N N+1 TI00 Rising edge detection N CR01 INTTM01 <4> The capture operation is performed at the fall of the count clock. An interrupt request input (INTTM0n), however, occurs at the rise of the next count clock. (9) Compare operation <1> When the 16-bit timer capture/compare register (CR00/CR01) is overwritten during timer operation, match interrupt may be generated or the clear operation may not be performed normally if that value is close to or large than the timer value. <2> The capture operation may not be performed for CR00/CR01 set in compare mode even if a capture trigger is input. (10) Edge detection <1> If the TI00 pin or the TI01 pin is high level immediately after system reset and the rising edge or both the rising and falling edges are specified as the valid edge for the TI00 pin or TI01 pin to enable 16-bit timer counter 0 (TM0) operation, a rising edge is detected immediately. Be careful when pulling up the TI00 pin or the TI01 pin. However, the rising edge is not detected at restart after the operation has been stopped once. <2> The sampling clock used to remove noise differs when a TI00 valid edge is used as the count clock and when it is used as a capture trigger. In the former case, the count clock is fX/23, and in the latter case the count clock is selected by prescaler mode register 0 (PRM0). The capture operation is not performed until the valid edge is sampled and the valid level is detected twice, thus eliminating noise with a short pulse width. (11) STOP mode or main system clock stop mode setting Except when TI00, TI01 input is selected, stop the timer operation before setting STOP mode or main system clock stop mode; otherwise the timer may malfunction when the main system clock starts. 216 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.1 Functions of 8-Bit Timer/Event Counters 50, 51 8-bit timer/event counters 50, 51 (TM50, TM51) have the following two modes. (1) Mode using 8-bit timer/event counters 50, 51 alone (discrete mode) The timer operates as 8-bit timer/event counter 50 or 51. It has the following functions. <1> Interval timer Interrupt requests are generated at the preset interval. * Number of counts: 1 to 256 <2> External event counter The number of pulses with high/low level widths of the signal input externally can be measured. <3> Square-wave output A square wave with an arbitrary frequency can be output. * Cycle: (1 x 2 to 256 x 2) x Cycles of count clock <4> PWM output A pulse with an arbitrary duty ratio can be output. Count clock x 256 * Cycle: * Duty ratio: Set value of compare register/256 (2) Mode using cascade connection (16-bit resolution: cascade connection mode) The timer operates as a 16-bit timer/event counter by combining two 8-bit timer/event counters. It has the following functions. * Interval timer with 16-bit resolution * External event counter with 16-bit resolution * Square-wave output with 16-bit resolution Figures 9-1 and 9-2 show block diagrams of 8-bit timer/event counters 50 and 51. User's Manual U14046EJ5V0UD 217 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-1. Block Diagram of 8-Bit Timer/Event Counter 50 Internal bus Selector Note 2 S Q INV 8-bit timer OVF counter 50 (TM50) R Clear INTTM50 Selector Match Selector TI50/TO50/P72Note 1 fX fX/22 fX/24 fX/26 fX/28 fX/210 Mask circuit 8-bit timer compare register 50 (CR50) TO50/TI50/ P72Note 1 Note 3 S 3 Invert level R Selector Output latch (P72) PM72 TCE50 TMC506 TMC504 LVS50 LVR50 TMC501 TOE50 TCL502 TCL501 TCL500 8-bit timer mode control register 50 (TMC50) Timer clock select register 50 (TCL50) Internal bus Figure 9-2. Block Diagram of 8-Bit Timer/Event Counter 51 Internal bus 8-bit timer counter 51 (TM51) Selector Note 2 S Q INV OVF R Clear TO51/TI51/ P73Note 1 Note 3 S 3 R Selector TCL512 TCL511 TCL510 Timer clock select register 51 (TCL51) INTTM51 Selector Match Selector TI51/TO51/P73Note 1 fX/2 fX/23 fX/25 fX/27 fX/29 fX/211 Mask circuit 8-bit timer compare register 51 (CR51) Invert level Output latch (P73) PM73 TCE51 TMC516 TMC514 LVS51 LVR51 TMC511 TOE51 8-bit timer mode control register 51 (TMC51) Internal bus Notes 1. The respective combinations, TI50 input and TO50 output, and TI51 input and TO51 output, cannot be used at the same time. 2. Timer output F/F 3. PWM output F/F 218 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.2 Configuration of 8-Bit Timer/Event Counters 50, 51 8-bit timer/event counters 50, 51 consist of the following hardware. Table 9-1. Configuration of 8-Bit Timer/Event Counters 50, 51 Item Configuration Timer counter 8-bit timer counter 5n (TM5n) Register 8-bit timer compare register 5n (CR5n) Timer input TI5n Timer output TO5n Control registers Timer clock select register 5n (TCL5n) 8-bit timer mode control register 5n (TMC5n) Port mode register 7 (PM7) Port 7 (P7) (1) 8-bit timer counter 5n (TM5n: n = 0, 1) TM5n is an 8-bit read-only register that counts the count pulses. The counter is incremented in synchronization with the rising edge of the count clock. When TM50 and TM51 can be connected in cascade and used as a 16-bit timer, they can be read by a 16-bit memory manipulation instruction. However, since they are connected by an internal 8-bit bus, TM50 and TM51 are read separately twice in that order. Thus, take reading during the count change into consideration and compare them by reading twice. When the count value is read during operation, the count clock input is temporarily stoppedNote, and then the count value is read. In the following situations, count value is cleared to 00H. <1> RESET input <2> When TCE5n is cleared <3> When TM5n and CR5n match in the clear & start mode entered on a match between TM5n and CR5n. Note An error may occur in the count. Select a count clock with a high/low-level waveform longer than two cycles of the CPU clock. Caution In cascade connection mode, the count value is reset to 0000H when TCE50 of the lowest timer is cleared. (2) 8-bit timer compare register 5n (CR5n: n = 0, 1) When CR5n is used as a compare register in other than PWM mode, the value set in CR5n is constantly compared with the 8-bit timer counter 5n (TM5n) count value, and an interrupt request (INTTM5n) is generated if they match. In PWM mode, the TO5n pin goes to the active level by the overflow of TM5n. When the values of TM5n and CR5n match, the TO5n pin goes to the inactive level. It is possible to rewrite the value of CR5n within 00H to FFH during a count operation. When TM50 and TM51 can be connected in cascade and used as a 16-bit timer, CR50 and CR51 operate as a 16-bit compare register. This register compares the count value with the register value, and if the values match, an interrupt request (INTTM50) is generated. The INTTM51 interrupt request is also generated at this time. Thus, mask the INTTM51 interrupt request. CR5n is set by an 8-bit memory manipulation instruction. RESET input makes CR5n undefined. Caution In cascade connection mode, stop the timer operation before setting data. Remark n = 0, 1 User's Manual U14046EJ5V0UD 219 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.3 Registers to Control 8-Bit Timer/Event Counters 50, 51 The following four types of registers are used to control 8-bit timer/event counters 50, 51. * Timer clock select register 5n (TCL5n) * 8-bit timer mode control register 5n (TMC5n) * Port mode register 7 (PM7) * Port 7 (P7) Remark n = 0, 1 (1) Timer clock select register 5n (TCL5n: n = 0, 1) This register sets the count clock of 8-bit timer/event counter 5n and the valid edge of TI50, TI51 input. TCL5n is set by an 8-bit memory manipulation instruction. RESET input clears TCL5n to 00H. Figure 9-3. Format of Timer Clock Select Register 50 (TCL50) Address: FF71H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 TCL50 0 0 0 0 0 TCL502 TCL501 TCL500 TCL502 TCL501 TCL500 Count clock selection fX = 8.38 MHz fX = 12 MHzNote 0 0 0 TI50 falling edge - - 0 0 1 TI50 rising edge - - 0 1 0 fX 8.38 MHz 12 MHz 0 1 1 fX/22 2.09 MHz 3 MHz 1 0 0 fX/24 523 kHz 750 kHz 1 0 1 fX/26 131 kHz 187 kHz 1 1 0 fX/28 32.7 kHz 46.8 kHz 1 1 1 fX/210 8.18 kHz 11.7 kHz Note Expanded-specification products of PD780024A, 780034A Subseries only. Cautions 1. When rewriting TCL50 to other data, stop the timer operation beforehand. 2. Be sure to clear bits 3 to 7 to 0. Remarks 1. When cascade connection is used, only TCL50 is valid for count clock setting. 2. fX: Main system clock oscillation frequency 220 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-4. Format of Timer Clock Select Register 51 (TCL51) Address: FF79H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 TCL51 0 0 0 0 0 TCL512 TCL511 TCL510 TCL512 TCL511 TCL510 Count clock selection fX = 8.38 MHz fX = 12 MHzNote 0 0 0 TI51 falling edge - - 0 0 1 TI51 rising edge - - 0 1 0 fX/2 4.19 MHz 6 MHz 0 1 1 fX/23 1.04 MHz 1.5 MHz 1 0 0 fX/25 261 kHz 375 kHz 1 0 1 fX/27 65.4 kHz 93.7 kHz 1 1 0 fX/29 16.3 kHz 23.4 kHz 1 1 1 fX/211 4.09 kHz 5.85 kHz Note Expanded-specification products of PD780024A, 780034A Subseries only. Cautions 1. When rewriting TCL51 to other data, stop the timer operation beforehand. 2. Be sure to clear bits 3 to 7 to 0. Remarks 1. When cascade connection is used, only TCL50 is valid for count clock setting. 2. fX: Main system clock oscillation frequency (2) 8-bit timer mode control register 5n (TMC5n: n = 0, 1) TMC5n is a register that makes the following six settings. <1> 8-bit timer counter 5n (TM5n) count operation control <2> 8-bit timer counter 5n (TM5n) operating mode selection <3> Discrete mode/cascade connection mode selection (TMC51 only) <4> Timer output F/F (flip-flop) status setting <5> Active level selection in timer F/F control or PWM (free-running) mode. <6> Timer output control TMC5n is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears TMC5n to 00H. User's Manual U14046EJ5V0UD 221 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-5. Format of 8-Bit Timer Mode Control Register 50 (TMC50) Address: FF70H After reset: 00H R/W Symbol <7> 6 5 4 <3> <2> 1 <0> TMC50 TCE50 TMC506 0 0 LVS50 LVR50 TMC501 TOE50 TCE50 TM50 count operation control 0 After clearing to 0, count operation disabled (prescaler disabled) 1 Count operation start TMC506 TM50 operating mode selection 0 Clear and start mode by match between TM50 and CR50 1 PWM (free-running) mode LVS50 LVR50 0 0 No change 0 1 Timer output F/F reset (0) 1 0 Timer output F/F set (1) 1 1 Setting prohibited TMC501 Timer output F/F status setting In other modes (TMC506 = 0) In PWM mode (TMC506 = 1) Timer F/F control Active level selection 0 Inversion operation disabled Active high 1 Inversion operation enabled Active low TOE50 Timer output control 0 Output disabled (port mode) 1 Output enabled Remarks 1. In PWM mode, PWM output will be inactive because TCE50 = 0. 2. If LVS50 and LVR50 are read after data is set, 0 is read. 222 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-6. Format of 8-Bit Timer Mode Control Register 51 (TMC51) Address: FF78H After reset: 00H R/W Symbol <7> 6 5 4 <3> <2> 1 <0> TMC51 TCE51 TMC516 0 TMC514 LVS51 LVR51 TMC511 TOE51 TCE51 TM51 count operation control 0 After clearing to 0, count operation disabled (prescaler disabled) 1 Count operation start TMC516 TM51 operating mode selection 0 Clear and start mode by match between TM51 and CR51 1 PWM (free-running) mode TMC514 Discrete mode/cascade connection mode selection 0 Discrete mode 1 Cascade connection mode (TM50: Lower timer, TM51: Higher timer) LVS51 LVR51 0 0 No change 0 1 Timer output F/F reset (0) 1 0 Timer output F/F set (1) 1 1 Setting prohibited TMC511 Timer output F/F status setting In other modes (TMC516 = 0) In PWM mode (TMC516 = 1) Timer F/F control Active level selection 0 Inversion operation disabled Active high 1 Inversion operation enabled Active low TOE51 Timer output control 0 Output disabled (port mode) 1 Output enabled Remarks 1. In PWM mode, PWM output will be inactive because TCE51 = 0. 2. If LVS51 and LVR51 are read after data is set, 0 is read. User's Manual U14046EJ5V0UD 223 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 (3) Port mode register 7 (PM7) This register sets port 7 input/output in 1-bit units. When using the P72/TO50/TI50 and P73/TI51/TO51 pins for timer output, clear PM72, PM73, and the output latches of P72 and P73 to 0. When using the P72/TO50/TI50 and P73/TI51/TO51 pins for timer input, set PM72 and PM73 to 1. At this time, the output latches of P72 and P73 can be either 0 or 1. PM7 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM7 to FFH. Figure 9-7. Format of Port Mode Register 7 (PM7) Address: FF27H R/W Symbol 7 6 5 4 3 2 1 0 PM7 1 1 PM75 PM74 PM73 PM72 PM71 PM70 PM7n 224 After reset: FFH P7n pin I/O mode selection (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.4 Operation of 8-Bit Timer/Event Counters 50, 51 9.4.1 8-bit interval timer operation The 8-bit timer/event counters operate as interval timers that generate interrupt requests repeatedly at intervals of the count value preset to 8-bit timer compare register 5n (CR5n). When the count value of 8-bit timer counter 5n (TM5n) matches the value set to CR5n, counting continues with the TM5n value cleared to 0 and an interrupt request signal (INTTM5n) is generated. The count clock of TM5n can be selected with bits 0 to 2 (TCL5n0 to TCL5n2) of timer clock select register 5n (TCL5n). [Setting] <1> Set the registers. * TCL5n: Select count clock. * CR5n: Compare value * TMC5n: Count operation stop, clear & start mode on match between TM5n and CR5n. (TMC5n = 0000xxx0B x = don't care) <2> After TCE5n = 1 is set, count operation starts. <3> If the values of TM5n and CR5n match, INTTM5n is generated (TM5n is cleared to 00H). <4> INTTM5n is generated repeatedly at the same interval. Clear TCE5n to 0 to stop the count operation. Remark n = 0, 1 User's Manual U14046EJ5V0UD 225 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-8. Interval Timer Operation Timing (1/3) (a) Basic operation t Count clock TM5n count value 00H 01H Start count CR5n N N 00H 01H Clear N 00H 01H Clear N N N TCE5n INTTM5n Interrupt acknowledged Interrupt acknowledged TO5n Interval time Remarks 1. Interval time = (N + 1) x t N = 00H to FFH 2. n = 0, 1 226 N User's Manual U14046EJ5V0UD Interval time CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-8. Interval Timer Operation Timing (2/3) (b) When CR5n = 00H t Count clock TM5n 00H 00H 00H CR5n 00H 00H TCE5n INTTM5n TO5n Interval time (c) When CR5n = FFH t Count clock TM5n CR5n 01H FFH FEH FFH 00H FEH FFH FFH 00H FFH TCE5n INTTM5n Interrupt acknowledged Interrupt acknowledged TO5n Interval time Remark n = 0, 1 User's Manual U14046EJ5V0UD 227 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-8. Interval Timer Operation Timing (3/3) (d) Operated by CR5n transition (M < N) Count clock TM5n N 00H CR5n M N FFH 00H N M 00H M TCE5n H INTTM5n TO5n CR5n transition TM5n overflows since M < N (e) Operated by CR5n transition (M > N) Count clock TM5n N-1 CR5n N 00H 01H N N M TCE5n H INTTM5n TO5n CR5n transition Remark n = 0, 1 228 M-1 User's Manual U14046EJ5V0UD M 00H 01H CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.4.2 External event counter operation The external event counter counts the number of external clock pulses to be input to TI5n using 8-bit timer counter 5n (TM5n). TM5n is incremented each time the valid edge specified by timer clock select register 5n (TCL5n) is input. Either the rising or falling edge can be selected. When the TM5n count value matches the value of 8-bit timer compare register 5n (CR5n), TM5n is cleared to 0 and an interrupt request signal (INTTM5n) is generated. Whenever the TM5n count value matches the value of CR5n, INTTM5n is generated. [Setting] <1> Set each register * TCL5n: Edge selection of TI5n input Falling edge of TI5n TCL5n = 00H Rising edge of TI5n TCL5n = 01H * CR5n: Compare value * TMC5n: Count operation stop, clear & start mode on match between TM5n and CR5n, timer F/F inverted operation disable, timer output disable (TMC5n = 0000xx00B, x = don't care) <2> When TCE5n = 1 is set, the number of pulses input from TI5n is counted. <3> When the values of TM5n and CR5n match, INTTM5n is generated (TM5n is cleared to 00H). <4> Each time the values of TM5n and CR5n match, INTTM5n is generated. Figure 9-9. External Event Counter Operation Timing (with Rising Edge Specified) TI5n TM5n count value 00H 01H 02H 03H 04H 05H CR5n N-1 N 00H 01H 02H 03H N INTTM5n Remarks 1. N = 00H to FFH 2. n = 0, 1 User's Manual U14046EJ5V0UD 229 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.4.3 Square-wave output (8-bit resolution) operation A square wave with any selected frequency is output at intervals determined by the value preset to 8-bit timer compare register 5n (CR5n). The TO5n pin output status is reversed at intervals determined by the count value preset to CR5n by setting bit 0 (TOE5n) of 8-bit timer mode control register 5n (TMC5n) to 1. This enables a square wave with any selected frequency to be output (duty = 50%). [Setting] <1> Set each register * Clear port latches (P72, P73)Note and port mode registers (PM72, PM73)Note to 0. * TCL5n: Select count clock * CR5n: Compare value * TMC5n: Count operation stop, clear & start mode on match between TM5n and CR5n LVS5n LVR5n Timer Output F/F Status Setting 1 0 High-level output 0 1 Low-level output Timer output F/F reverse enable Timer output enable TOE5n = 1 (TMC5n = 00001011B or 00000111B) <2> After TCE5n = 1 is set, the count operation starts. <3> Timer output F/F is reversed by match between TM5n and CR5n. After INTTM5n is generated, TM5n is cleared to 00H. <4> Timer output F/F is reversed at the same interval and a square wave is output from TO5n. The frequency is as follows. * Frequency = fCNT/2 (N + 1) (N = 00H to FFH, fCNT: Count clock) Note 8-bit timer/event counter 50: P72, PM72 8-bit timer/event counter 51: P73, PM73 230 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-10. Square-Wave Output Operation Timing Count clock TM5n count value 00H 01H 02H N-1 N 00H 01H 02H N-1 N 00H Count start N CR5n TO5nNote Note The TO5n output initial value can be set by bits 2 and 3 (LVR5n, LVS5n) of 8-bit timer mode control register 5n (TMC5n). Remarks 1. N = 00H to FFH 2. n = 0, 1 9.4.4 8-bit PWM output operation The 8-bit timer/event counter operates as PWM output when bit 6 (TMC5n6) of 8-bit timer mode control register 5n (TMC5n) is set to 1. The duty ratio pulse is determined by the value set to 8-bit timer compare register 5n (CR5n). Set the active level width of the PWM pulse to CR5n. The active level can be selected with bit 1 (TMC5n1) of TMC5n. The count clock can be selected with bits 0 to 2 (TCL5n0 to TCL5n2) of timer clock select register 5n (TCL5n). PWM output enable/disable can be selected with bit 0 (TOE5n) of TMC5n. * Cycle = Count clock x 256 * Duty ratio = Set value of compare register 256 Caution CR5n can be rewritten in PWM mode only once per cycle. Remark n = 0, 1 User's Manual U14046EJ5V0UD 231 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 (1) PWM output basic operation [Setting] <1> Set each register. * Clear port latches (P72, P73)Note and port mode registers (PM72, PM73)Note to 0. * TCL5n: Count clock selection * CR5n: * TMC5n: Count operation stop, PWM mode selection, timer output F/F not changed Compare value TMC5n1 Active Level Selection 0 Active high 1 Active low Timer output enabled (TMC5n = 01000001B or 01000011B) <2> When TCE5n = 1 is set, the count operation is started. To stop the count operation, clear TCE5n to 0. Note 8-bit timer/event counter 50: P72, PM72 8-bit timer/event counter 51: P73, PM73 [PWM output operation] <1> PWM output (output from TO5n) outputs an inactive level after the count operation starts until an overflow occurs. <2> When an overflow occurs, the active level is output. The active level is output until CR5n matches the count value of 8-bit timer counter 5n (TM5n). <3> After CR5n matches the count value, PWM output outputs the inactive level again until an overflow occurs. <4> Operations <2> and <3> are repeated until the count operation stops. <5> When the count operation is stopped by setting TCE5n = 0, PWM output becomes the inactive level. Remark n = 0, 1 232 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Figure 9-11. PWM Output Operation Timing (a) Basic operation (active level = H) Count clock TM5n 00H 01H CR5n N FFH 00H 01H 02H N N+1 FFH 00H 01H 02H M 00H TCE5n INTTM5n TO5n Inactive level Active level Active level (b) CR5n = 0 Count clock TM5n 00H 01H CR5n 00H FFH 00H 01H 02H N N+1 N+2 FFH 00H 01H 02H M 00H TCE5n INTTM5n TO5n L Inactive level Inactive level (c) CR5n = FFH Count clock TM5n 00H 01H CR5n FFH FFH 00H 01H 02H N N+1 N+2 FFH 00H 01H 02H M 00H TCE5n INTTM5n TO5n Inactive level Active level Active level Inactive level Inactive level Remark n = 0, 1 User's Manual U14046EJ5V0UD 233 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 (2) Operated by CR5n transition Figure 9-12. Timing of Operation by Change of CR5n (a) CR5n value is changed from N to M when TM5n > CR5n Count clock TM5n N N+1 N+2 CR5n N TCE5n INTTM5n FFH 00H 01H 02H M M+1 M+2 FFH 00H 01H 02H M M+1 M+2 M H TO5n CR5n transition (N M) (b) CR5n value is changed from N to M when TM5n < CR5n Count clock TM5n N N+1 N+2 CR5n TCE5n INTTM5n N FFH 00H 01H 02H 03H N N+1 N+2 N M H TO5n CR5n transition (N M) Remark n = 0, 1 234 FFH 00H 01H 02H User's Manual U14046EJ5V0UD M M+1 M+2 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.4.5 Interval timer (16-bit) operations When bit 4 (TMC514) of 8-bit timer mode control register 51 (TMC51) is set to 1, the 16-bit resolution timer/counter mode is entered. The 8-bit timer/event counter operates as an interval timer that generates interrupt requests repeatedly at intervals of the count value preset to the 8-bit timer compare registers (CR50, CR51). [Setting] <1> Set each register TCL50: Select count clock for TM50. CR50, CR51: Compare value (each value can be set to 00H to FFH) Cascade-connected TM51 need not be selected. TMC50, TMC51: Select the clear & start mode entered on a match between TM50 and CR50 (TM51 and CR51). TM50 TMC50 = 0000xxx0B x: don't care TM51 TMC51 = 0001xxx0B x: don't care <2> When TMC51 is set to TCE51 = 1 and then TMC50 is set to TCE50 = 1, the count operation starts. <3> When the values of TM50 and CR50 of the cascade-connected timer match, INTTM50 of TM50 is generated (TM50 and TM51 are cleared to 00H). <4> INTTM50 is generated repeatedly at the same interval. Cautions 1. Stop the timer operation without fail before setting the compare registers (CR50, CR51). 2. INTTM51 of TM51 is generated when the TM51 count value matches CR51, even if cascade connection is used. Be sure to mask TM51 to disable interrupts. 3. Set TCE50 and TCE51 in order of TM51 then TM50. 4. Count restart/stop can only be controlled by setting TCE50 of TM50 to 1/0. Figure 9-13 shows an example of 16-bit resolution cascade connection mode timing. Figure 9-13. 16-Bit Resolution Cascade Connection Mode Count clock TM50 00H TM51 00H CR50 CR51 01H N N+1 FFH 00H FFH 00H 01H 02H FFH 00H 01H M-1 M N 00H 01H A 00H 00H B 00H N M TCE50 TCE51 INTTM50 Interval time TO50 Interrupt request generation Level reverse Counter clear Operation enable Count start User's Manual U14046EJ5V0UD Operation stop 235 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.5 Program List Caution The following sample program is shown as an example to describe the operation of semiconductor products and their applications. Therefore, when applying the following information to your devices, design the devices after performing evaluation under your own responsibility. 9.5.1 Interval timer (8-bit) /*************************************************************************************/ /* */ /* Timer 50 operation sample */ /* Interval timer setting example (cycle change by interrupt servicing) */ /* data[0]: Data set flag (value changed when other than 00) */ /* data[1]: Set data */ /* */ /*************************************************************************************/ #pragma sfr #pragma EI #pragma DI #pragma interrupt INTTM50 intervalint rb2 unsigned char data[2]; /* Data area */ void main(void) { PCC = 0x0; data[0] = 0; data[1] = 0; P7 = 0b11111011; PM7.2 = 0; TMMK50 = 0; TMC50 = 0b00000111; TCL50 = 0b00000101; CR50 = 131; TCE50 = 1; EI(); while(1); /* Set high-speed operation mode */ /* Clear data area */ /* Set port */ /* When using TO50 */ /* Set P72 to output */ /* /* /* /* /* /* /* /* Set interrupt */ Clear INTTM50 interrupt mask */ Set timer 50 */ Clear & start mode, initial value L */ Both rising and falling edges */ Count clock is fx/2^6 */ Set interval to 1 ms as initial value */ Timer start */ /* Dummy loop */ } /* INTTM50 interrupt function */ void intervalint() { if(data[0] != 0) { CR50 = data[1]; data[0] = 0; } /* Set new set value */ /* Clear request flag */ } 236 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.5.2 External event counter /***************************************************************/ /* */ /* Timer 50 operation sample */ /* Event counter setting example */ /* data: Count up flag */ /* */ /***************************************************************/ #pragma sfr #pragma EI #pragma DI #pragma interrupt INTTM50 intervalint rb2 unsigned char data; /* Data area */ void main(void) { PCC = 0x0; data = 0; PM7.2 = 1; TMMK50 = 0; TMC50 = 0b00000000; TCL50 = 0b00000001; CR50 = 0x10; TCE50 = 1; EI(); /* Set high-speed operation mode */ /* Clear data area */ /* Set port /* Set P72 to input */ /* /* /* /* /* /* /* */ Set interrupt Clear INTTM50 interrupt mask Set timer 50 Clear & start mode Specify rising edge of TI50 Set N = 16 as initial value Timer start */ */ */ */ */ */ */ /*************************************************************/ /* */ /* Describe the processing to be executed */ /* */ /*************************************************************/ while(data == 0); /* Wait for count up */ /*************************************************************/ /* */ /* Describe the processing after count up below */ /* */ /*************************************************************/ } /* INTTM50 interrupt function */ void intervalint() { data = 0xff; TCE50 = 0; } /* Set count up flag /* Timer stop User's Manual U14046EJ5V0UD */ */ 237 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.5.3 Interval timer (16-bit) /***************************************************************/ /* */ /* Timer 5 operation sample */ /* Cascade connection setting example */ /* */ /***************************************************************/ #pragma sfr #pragma EI #pragma DI #define intervalTM5 130 /* Cycle data to be set to CR */ #pragma interrupt INTTM50 ppgint rb2 unsigned char ppgdata[2]; /* Data area to be set to timer 5 */ void main(void) { int interval; interval = intervalTM5; PCC = 0x0; ppgdata[0] = 0; ppgdata[1] = 0; P7 = 0b11111011; PM7.2 = 0; TMMK50 = 0; TMMK51 = 1; TCL50 = 0b00000101; CR50 = interval & 0xff; CR51 = interval >> 8; TMC50 = 0b00000111; TMC51 = 0b00010000; TCE51 = 1; TCE50 = 1; EI(); /* /* /* /* /* /* /* /* /* /* /* /* /* /* /* Select high-speed operation mode */ Clear CR50 data */ Clear CR51 data */ Set port */ Clear P72 */ Set P72 to output */ Set interrupt */ Clear INTTM50 interrupt mask */ Set INTTM51 interrupt mask */ Set timer 5 */ Count clock is fx/2^6 */ Set lower compare register to CR50 */ Set higher compare register to CR51 */ Inverted on match, initial value L */ Cascade mode */ /* Timer starts */ while(1); } /* Timer 5 interrupt function */ void ppgint() { unsigned int work; work = ppgdata[0]+ppgdata[1]*0x100; if (work != 0) { TCE50 =0; CR51 = work >> 8; CR50 = work & 0xff; ppgdata[0] = 0; ppgdata[1] = 0; if (work != 0xffff) { TCE50 = 1; /* Timer resumes */ } } } 238 User's Manual U14046EJ5V0UD CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 9.6 Cautions Related to 8-Bit Timer/Event Counters 50, 51 (1) Timer start errors An error of up to one clock may occur in the time required for a match signal to be generated after timer start. This is because 8-bit timer counter 5n (TM5n) is started asynchronously to the count pulse. Figure 9-14. Start Timing of 8-Bit Timer Counter 5n (TM5n) Count pulse TM5n count 00H 01H 02H 03H 04H Timer start (2) Setting STOP mode or main system clock stop mode Except when TI5n input is selected, always set TCE5n = 0 before setting the STOP mode or main system clock stop mode. The timer may malfunction when the main system clock starts oscillating. (3) TM5n (n = 0, 1) reading during timer operation When reading TM5n during operation, the count clock stops temporarily, so select a count clock with a high/lowlevel waveform longer than two cycles of the CPU clock. For example, in the case where the CPU clock (fCPU) is fX, when the selected count clock is fX/4 or below, it can be read. Remark n = 0, 1 User's Manual U14046EJ5V0UD 239 CHAPTER 10 WATCH TIMER 10.1 Watch Timer Functions The watch timer has the following functions. (1) Watch timer When the main system clock or subsystem clock is used, interrupt requests (INTWT) are generated at 214/fW second intervals. (2) Interval timer Interrupt requests (INTWTI) are generated at the preset time interval. For the interval time, see Table 10-2. The watch timer and the interval timer can be used simultaneously. Figure 10-1 shows the watch timer block diagram. Figure 10-1. Watch Timer Block Diagram fX/2 5-bit counter 9-bit prescaler fW fW 24 fW 25 fW 26 fW 27 fW 28 fW 29 INTWT Clear Selector fXT Selector Clear 7 WTM7 WTM6 WTM5 WTM4 WTM1 WTM0 Watch timer operation mode register (WTM) Internal bus Remark fW: Watch timer clock frequency (fX/27 or fXT) fX: Main system clock oscillation frequency fXT: Subsystem clock oscillation frequency 240 User's Manual U14046EJ5V0UD INTWTI CHAPTER 10 WATCH TIMER 10.2 Watch Timer Configuration The watch timer consists of the following hardware. Table 10-1. Watch Timer Configuration Item Configuration Counter 5 bits x 1 Prescaler 9 bits x 1 Control register Watch timer operation mode register (WTM) User's Manual U14046EJ5V0UD 241 CHAPTER 10 WATCH TIMER 10.3 Register to Control Watch Timer The watch timer is controlled by the watch timer operation mode register (WTM). * Watch timer operation mode register (WTM) This register sets the watch timer count clock, enables/disables operation, sets the prescaler interval time, and controls the 5-bit counter operation. WTM is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears WTM to 00H. Figure 10-2. Format of Watch Timer Operation Mode Register (WTM) Address: FF41H Symbol WTM After reset: 00H R/W 7 6 5 4 3 2 <1> <0> WTM7 WTM6 WTM5 WTM4 0 0 WTM1 WTM0 WTM7 Watch timer count clock selection 0 fX/27 (65.4 kHz: fX = 8.38 MHz, 93.7 kHz: fX = 12 MHzNote) 1 fXT (32.768 kHz: fXT = 32.768 kHz) WTM6 WTM5 WTM4 Prescaler interval time selection 0 0 0 24/fW 0 0 1 25/fW 0 1 0 26/fW 0 1 1 27/fW 1 0 0 28/fW 1 0 1 29/fW Other than above Setting prohibited WTM1 5-bit counter operation control 0 Clear after operation stop 1 Start WTM0 Watch timer operation enable 0 Operation stopped (both prescaler and timer cleared) 1 Operation enabled Note Expanded-specification products of PD780024A, 780034A Subseries only. Caution Do not change the count clock and interval time (by using bits 4 to 7 (WTM4 to WTM7) of WTM) while the watch timer is operating. Remarks 1. fW: Watch timer clock frequency (fX/27 or fXT) 2. fX: Main system clock oscillation frequency 3. fXT: Subsystem clock oscillation frequency 242 User's Manual U14046EJ5V0UD CHAPTER 10 WATCH TIMER 10.4 Watch Timer Operations 10.4.1 Watch timer operation The watch timer generates an interrupt request (INTWT) at specific time intervals (214/fW seconds) by using the main system clock or subsystem clock. The interrupt request is generated at the following time intervals: * If main system clock (8.38 MHz) is selected: 0.25 seconds * If subsystem clock (32.768 kHz) is selected: 0.5 seconds When bit 0 (WTM0) and bit 1 (WTM1) of the watch timer operation mode register (WTM) are set to 1, the count operation starts, and when these bits are cleared to 0, the 5-bit counter is cleared and the count operation stops. When the interval timer is simultaneously operated, a zero-second start can be achieved for the watch timer by setting WTM1 to 1 after clearing it to 0. In this case, however, the 9-bit prescaler is not cleared. Therefore, an error up to 29/fW seconds occurs in the first overflow (INTWT) after the zero-second start. Remark fW: Watch timer clock frequency (fX/27 or fXT) 10.4.2 Interval timer operation The watch timer operates as interval timer that generates interrupt requests (INTWTI) repeatedly at an interval of the preset count value. The interval time can be selected with bits 4 to 6 (WTM4 to WTM6) of the watch timer operation mode register (WTM). Table 10-2. Interval Timer Interval Time WTM6 WTM5 WTM4 Interval Time When Operated at fX = 12 MHzNote When Operated at fX = 8.38 MHz When Operated at fX = 4.19 MHz 0 0 0 0 24/fW 170 s 244 s 488 s 488 s 0 1 25/fW 341 s 488 s 977 s 976 s 0 1 0 26/fW 682 s 977 s 1.95 ms 1.95 ms 0 1 1 27/fW 1.36 ms 1.95 ms 3.91 ms 3.90 ms 0 28/fW 2.73 ms 3.91 ms 7.82 ms 7.81 ms 1 29/fW 5.46 ms 7.82 ms 15.6 ms 15.6 ms 1 1 0 0 Other than above When Operated at fXT = 32.768 kHz Setting prohibited Note Expanded-specification products of PD780024A, 780034A Subseries only. Remark fW: Watch timer clock frequency (fX/27 or fXT) fX: Main system clock oscillation frequency fXT: Subsystem clock oscillation frequency User's Manual U14046EJ5V0UD 243 CHAPTER 10 WATCH TIMER Figure 10-3. Operation Timing of Watch Timer/Interval Timer 5-bit counter 0H Overflow Start Overflow Count clock Watch timer interrupt INTWT Interval timer interrupt INTWTI Interrupt time of watch timer (0.5 s) Interval time (T) Interrupt time of watch timer (0.5 s) T nxT nxT Caution If the watch timer and 5-bit counter are enabled by the watch timer mode control register (WTM) (by setting bits 0 (WTM0) and 1 (WTM1) of WTM to 1), the time from this setting to the occurrence of the first interrupt request (INTWT) is not exactly the watch timer interrupt time (0.25 or 0.5 seconds). This is because the 5-bit counter is late by one output cycle of the 9-bit prescaler in starting counting. The second INTWT signal and those that follow are generated exactly at the set time. Remark fW: Watch timer clock frequency (fX/27 or fXT) n: The number of interval timer operations Figures in parentheses are for operation with fW = 32.768 kHz. 244 User's Manual U14046EJ5V0UD CHAPTER 11 WATCHDOG TIMER 11.1 Watchdog Timer Functions The watchdog timer has the following functions. (1) Watchdog timer The watchdog timer detects a program loop. Upon detection of a program loop, a non-maskable interrupt request or RESET can be generated. For the loop detection time, see Table 11-2. (2) Interval timer Interrupt requests are generated at the preset time intervals. For the interval time, see Table 11-3. Caution Select the watchdog timer mode or the interval timer mode using the watchdog timer mode register (WDTM). (The watchdog timer and the interval timer cannot be used simultaneously.) Figure 11-1 shows a block diagram of the watchdog timer. Figure 11-1. Watchdog Timer Block Diagram fX fX/28 Clock input controller Divided clock selector Divider circuit Output controller INTWDT RESET RUN Division mode selector 3 WDT mode signal WDCS2 WDCS1 WDCS0 Watchdog timer clock select register (WDCS) RUN WDTM4 WDTM3 Watchdog timer mode register (WDTM) Internal bus User's Manual U14046EJ5V0UD 245 CHAPTER 11 WATCHDOG TIMER 11.2 Watchdog Timer Configuration The watchdog timer consists of the following hardware. Table 11-1. Watchdog Timer Configuration Item Configuration Control registers Watchdog timer clock select register (WDCS) Watchdog timer mode register (WDTM) 11.3 Registers to Control Watchdog Timer The following two registers are used to control the watchdog timer. * Watchdog timer clock select register (WDCS) * Watchdog timer mode register (WDTM) (1) Watchdog timer clock select register (WDCS) This register sets the overflow time of the watchdog timer and the interval timer. WDCS is set by an 8-bit memory manipulation instruction. RESET input clears WDCS to 00H. Figure 11-2. Format of Watchdog Timer Clock Select Register (WDCS) Address: FF42H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 WDCS 0 0 0 0 0 WDCS2 WDCS1 WDCS0 WDCS2 WDCS1 WDCS0 0 0 0 0 1 0 0 1 1 0 Overflow time of watchdog timer/interval timer fX = 8.38 MHz fX = 12 MHzNote 0 212/fX 488 s 341 s 1 213/fX 977 s 682 s 0 214/fX 1.95 ms 1.36 ms 1 215/fX 3.91 ms 2.73 ms 0 216/fX 7.82 ms 5.46 ms 15.6 ms 10.9 ms 1 0 1 217/fX 1 1 0 218/fX 31.2 ms 21.8 ms 1 1 1 220/fX 125 ms 87.3 ms Note Expanded-specification products of PD780024A, 780034A Subseries only. Remark fX: Main system clock oscillation frequency 246 User's Manual U14046EJ5V0UD CHAPTER 11 WATCHDOG TIMER (2) Watchdog timer mode register (WDTM) This register sets the watchdog timer operating mode and enables/disables counting. WDTM is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears WDTM to 00H. Figure 11-3. Format of Watchdog Timer Mode Register (WDTM) Address: FFF9H After reset: 00H R/W Symbol <7> 6 5 4 3 2 1 0 WDTM RUN 0 0 WDTM4 WDTM3 0 0 0 Watchdog timer operation mode selectionNote 1 RUN 0 Count stop 1 Counter is cleared and counting starts Watchdog timer operation mode selectionNote 2 WDTM4 WDTM3 0 x Interval timer modeNote 3 (Maskable interrupt request occurs upon generation of overflow) 1 0 Watchdog timer mode 1 (Non-maskable interrupt request occurs upon generation of overflow) 1 1 Watchdog timer mode 2 (Reset operation is activated upon generation of overflow) Notes 1. Once set to 1, RUN cannot be cleared to 0 by software. Thus, once counting starts, it can only be stopped by RESET input. 2. Once set to 1, WDTM3 and WDTM4 cannot be cleared to 0 by software. 3. The watchdog timer starts operation as an interval timer when RUN is set to 1. Caution When RUN is set to 1 so that the watchdog timer is cleared, the actual overflow time is up to 28/fX seconds shorter than the time set by the watchdog timer clock select register (WDCS). Remark x: Don't care User's Manual U14046EJ5V0UD 247 CHAPTER 11 WATCHDOG TIMER 11.4 Watchdog Timer Operations 11.4.1 Watchdog timer operation When bit 4 (WDTM4) of the watchdog timer mode register (WDTM) is set to 1, the watchdog timer is operated to detect a program loop. The loop detection time interval is selected with bits 0 to 2 (WDCS0 to WDCS2) of the watchdog timer clock select register (WDCS). The watchdog timer starts by setting bit 7 (RUN) of WDTM to 1. After the watchdog timer is started, set RUN to 1 within the set loop time interval. The watchdog timer can be cleared and counting is started by setting RUN to 1. If RUN is not set to 1 and the loop detection time is exceeded, system reset or a non-maskable interrupt request is generated according to the value of WDTM bit 3 (WDTM3). The watchdog timer continues operating in the HALT mode but it stops in the STOP mode. Thus, set RUN to 1 before the STOP mode is set, clear the watchdog timer and then execute the STOP instruction. Cautions 1. The actual loop detection time may be shorter than the set time by up to 28/fX seconds. 2. When the subsystem clock is selected for the CPU clock, the watchdog timer count operation is stopped. Table 11-2. Watchdog Timer Loop Detection Time Loop Detection Time When Operated at fX = 8.38 MHz When Operated at fX = 12 MHzNote 212/fX 488 s 341 s 213/fX 977 s 682 s 214/fX 1.95 ms 1.36 ms 215/fX 3.91 ms 2.73 ms 216/fX 7.82 ms 5.46 ms 217/fX 15.6 ms 10.9 ms 218/fX 31.2 ms 21.8 ms 220/fX 125 ms 87.3 ms Note Expanded-specification products of PD780024A, 780034A Subseries only. Remark fX: Main system clock oscillation frequency 248 User's Manual U14046EJ5V0UD CHAPTER 11 WATCHDOG TIMER 11.4.2 Interval timer operation The watchdog timer operates as an interval timer that generates interrupt requests repeatedly at an interval of the preset count value when bit 4 (WDTM4) of the watchdog timer mode register (WDTM) is cleared to 0. The interval time of the interval timer is selected with bits 0 to 2 (WDCS0 to WDCS2) of the watchdog timer clock select register (WDCS). When bit 7 (RUN) of WDTM is set to 1, the watchdog timer operates as an interval timer. When the watchdog timer operates as an interval timer, the interrupt mask flag (WDTMK) and priority specification flag (WDTPR) are validated and the maskable interrupt request (INTWDT) can be generated. Among the maskable interrupts, INTWDT has the highest priority at default. The interval timer continues operating in the HALT mode but it stops in STOP mode. Thus, set RUN to 1 before the STOP mode is set, clear the interval timer and then execute the STOP instruction. Cautions 1. Once bit 4 (WDTM4) of WDTM is set to 1 (this selects the watchdog timer mode), the interval timer mode is not set unless RESET is input. 2. The interval time just after setting WDTM may be shorter than the set time by up to 28/fX seconds. 3. When the subsystem clock is selected for the CPU clock, the watchdog timer count operation is stopped. Table 11-3. Interval Timer Interval Time Interval Time When Operated at fX = 8.38 MHz When Operated at fX = 12 MHzNote 212/fX 488 s 341 s 213/fX 977 s 682 s 214/fX 1.95 ms 1.36 ms 215/fX 3.91 ms 2.73 ms 216/fX 7.82 ms 5.46 ms 217/fX 15.6 ms 10.9 ms 218/fX 31.2 ms 21.8 ms 220/fX 125 ms 87.3 ms Note Expanded-specification products of PD780024A, 780034A Subseries only. Remark fX: Main system clock oscillation frequency User's Manual U14046EJ5V0UD 249 CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER 12.1 Clock Output/Buzzer Output Controller Functions Clock output is used for carrier output during remote controlled transmission and clock output for supply to peripheral ICs. The clock selected by the clock output select register (CKS) is output. In addition, buzzer output is used for square-wave output of the buzzer frequency selected by CKS. Figure 12-1 shows the block diagram of the clock output/buzzer output controller. Figure 12-1. Block Diagram of Clock Output/Buzzer Output Controller fX 8 4 fX/210 to fX/213 Selector Prescaler BUZ/P75 BCS0, BCS1 fX to fX/27 fXT Selector BZOE Output latch (P75) PM75 Clock controller PCL/P74 CLOE Output latch (P74) BZOE BCS1 BCS0 CLOE CCS3 CCS2 CCS1 CCS0 Clock output select register (CKS) Internal bus 250 User's Manual U14046EJ5V0UD PM74 CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER 12.2 Configuration of Clock Output/Buzzer Output Controller The clock output/buzzer output controller consists of the following hardware. Table 12-1. Configuration of Clock Output/Buzzer Output Controller Item Control registers Configuration Clock output select register (CKS) Port mode register (PM7) Port 7 (P7) 12.3 Register to Control Clock Output/Buzzer Output Controller The following three registers are used to control the clock output/buzzer output controller. * Clock output select register (CKS) * Port mode register (PM7) * Port 7 (P7) (1) Clock output select register (CKS) This register sets output enable/disable for clock output (PCL) and for the buzzer frequency output (BUZ), and sets the output clock. CKS is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears CKS to 00H. User's Manual U14046EJ5V0UD 251 CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER Figure 12-2. Format of Clock Output Select Register (CKS) Address: FF40H After reset: 00H R/W Symbol CKS <7> 6 5 <4> 3 2 1 0 BZOE BCS1 BCS0 CLOE CCS3 CCS2 CCS1 CCS0 BZOE BUZ output enable/disable specification 0 Stop clock divider operation. BUZ fixed to low level. 1 Enable clock divider operation. BUZ output enabled. BCS1 BCS0 BUZ output clock selection fX = 12 MHzNote fX = 8.38 MHz 0 0 1 1 0 fX/210 8.18 kHz 11.7 kHz 1 fX/211 4.09 kHz 5.85 kHz 0 fX/212 2.04 kHz 2.92 kHz 1 fX/213 1.02 kHz 1.46 kHz CLOE PCL output enable/disable specification 0 Stop clock divider operation. PCL fixed to low level. 1 Enable clock divider operation. PCL output enabled. CCS3 CCS2 CCS1 CCS0 PCL output clock selection fX = 8.38 MHz fX = 12 MHzNote 0 0 0 0 fX 8.38 MHz 12 MHz 0 0 0 1 fX/2 4.19 MHz 6 MHz 0 fX/22 2.09 MHz 3 MHz 1 fX/23 1.04 MHz 1.5 MHz 523 kHz 750 kHz 0 0 0 0 1 1 0 1 0 0 fX/24 0 1 0 1 fX/25 261 kHz 375 kHz 0 1 1 0 fX/26 130 kHz 187 kHz 0 1 1 1 fX/27 65.4 kHz 93.7 kHz 1 0 0 0 fXT (32.768 kHz) Other than above Setting prohibited Note Expanded-specification products of PD780024A, 780034A Subseries only. Remarks 1. fX: Main system clock oscillation frequency 2. fXT: Subsystem clock oscillation frequency 3. Figures in parentheses are for operation with fXT = 32.768 kHz. 252 User's Manual U14046EJ5V0UD CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER (2) Port mode register (PM7) This register sets port 7 input/output in 1-bit units. When using the P74/PCL pin for clock output and the P75/BUZ pin for buzzer output, clear PM74, PM75 and the output latches of P74 and P75 to 0. PM7 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM7 to FFH. Figure 12-3. Format of Port Mode Register 7 (PM7) Address: FF27H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM7 1 1 PM75 PM74 PM73 PM72 PM71 PM70 PM7n P7n pin I/O mode selection (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD 253 CHAPTER 12 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER 12.4 Operation of Clock Output/Buzzer Output Controller 12.4.1 Operation as clock output The clock pulse is output using the following procedure. <1> Select the clock pulse output frequency using bits 0 to 3 (CCS0 to CCS3) of the clock output select register (CKS) (clock pulse output in disabled state). <2> Set bit 4 (CLOE) of CKS to 1, and enable clock output. Remark The clock output controller is designed not to output pulses with a small width during output enable/ disable switching of the clock output. As shown in Figure 12-4, be sure to start output from the low period of the clock (marked with * in the figure). When stopping output, do so after securing the high level of the clock. Figure 12-4. Remote Control Output Application Example CLOE * * Clock output 12.4.2 Operation as buzzer output The buzzer frequency is output using the following procedure. <1> Select the buzzer output frequency using bits 5 and 6 (BCS0, BCS1) of the clock output select register (CKS) (buzzer output in disabled state). <2> Set bit 7 (BZOE) of CKS to 1 to enable buzzer output. 254 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.1 A/D Converter Functions A/D converter is an 8-bit resolution converter that converts analog inputs into digital values. It can control up to 8 analog input channels (ANI0 to ANI7). (1) Hardware start Conversion is started by trigger input (ADTRG: rising edge, falling edge, or both rising and falling edges can be specified). (2) Software start Conversion is started by setting A/D converter mode register 0 (ADM0). Select one channel for analog input from ANI0 to ANI7 to perform A/D conversion. In the case of hardware start, A/D conversion stops when an A/D conversion operation ends and an interrupt request (INTAD0) is generated. In the case of software start, A/D conversion is repeated. Each time an A/D conversion operation ends, an interrupt request (INTAD0) is generated. Caution Although the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY incorporate a 10-bit A/D converter, this converter can be operated as an 8-bit A/D converter by using the device file DF780024. User's Manual U14046EJ5V0UD 255 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Figure 13-1. 8-Bit A/D Converter Block Diagram Series resistor string ANI0/P10 ANI1/P11 ANI2/P12 ANI3/P13 ANI4/P14 ANI5/P15 ANI6/P16 ANI7/P17 AVDD Voltage comparator Successive approximation register (SAR) Edge detector ADTRG/INTP3/P03 Controller AVREF Tap selector Selector Sample & hold circuit AVSS INTAD0 INTP3 3 Edge detector A/D conversion result register 0 (ADCR0) Note Trigger enable ADS02 ADS01 ADS00 ADSC0 TRG0 FR02 FR01 FR00 EGA01 EGA00 Analog input channel specification register 0 (ADS0) A/D converter mode register 0 (ADM0) Internal bus Note The valid edge of external interrupt is specified by bit 3 of the EGP and EGN registers (see Figure 19-5 Format of External Interrupt Rising Edge Enable Register (EGP), External Interrupt Falling Edge Enable Register (EGN)). 256 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.2 A/D Converter Configuration The A/D converter consists of the following hardware. Table 13-1. A/D Converter Configuration Item Configuration Analog input 8 channels (ANI0 to ANI7) Hardware trigger input 1 (ADTRG) Registers Successive approximation register (SAR) A/D conversion result register 0 (ADCR0) Control registers A/D converter mode register 0 (ADM0) Analog input channel specification register 0 (ADS0) (1) Successive approximation register (SAR) This register compares the analog input voltage value to the voltage tap (compare voltage) value applied from the series resistor string, and holds the result from the most significant bit (MSB). When up to the least significant bit (LSB) is held (end of A/D conversion), the SAR contents are transferred to A/D conversion result register 0 (ADCR0). (2) A/D conversion result register 0 (ADCR0) The ADCR0 is an 8-bit register that stores the A/D conversion result. Each time A/D conversion ends, the conversion result is loaded from the successive approximation register. ADCR0 is read by an 8-bit memory manipulation instruction. RESET input clears ADCR0 to 00H. Caution When writing is performed to A/D converter mode register 0 (ADM0) and analog input channel specification register 0 (ADS0), the contents of ADCR0 may become undefined. Read the conversion result following conversion completion before writing to ADM0, ADS0. Using a timing other than the above may cause an incorrect conversion result to be read. (3) Sample & hold circuit The sample & hold circuit samples the input signal of the analog input pin selected by the selector when A/D conversion is started and holds the sampled analog input voltage value during A/D conversion. (4) Voltage comparator The voltage comparator compares the sampled analog input voltage to the series resistor string output voltage. (5) Series resistor string The series resistor string is connected between AVREF and AVSS, and generates a voltage to be compared to the analog input. User's Manual U14046EJ5V0UD 257 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (6) ANI0 to ANI7 pins These are eight analog input pins to input analog signals to undergo A/D conversion to the A/D converter. ANI0 to ANI7 are alternate-function pins that can also be used for digital input. Cautions 1. Use ANI0 to ANI7 input voltages within the specification range. If a voltage higher than AVREF or lower than AVSS is applied (even if within the absolute maximum rating range), the conversion value of that channel will be undefined and the conversion values of other channels may also be affected. 2. Analog input (ANI0 to ANI7) pins are alternate function pins that can also be used as input port (P10 to P17) pins. When A/D conversion is performed by selecting any one of ANI0 to ANI7, do not access port 1 during conversion. It may cause the lower conversion resolution. 3. When a digital pulse is applied to a pin adjacent to the pin in the process of A/D conversion, A/D conversion values may not be obtained as expected due to coupling noise. Thus, do not apply any pulse to a pin adjacent to the pin in the process of A/D conversion. (7) AVREF pin This pin inputs the A/D converter reference voltage. It converts signals input to ANI0 to ANI7 into digital signals according to the voltage applied between AVREF and AVSS. Caution A series resistor string of several 10 k is connected between the AVREF pin and AVSS pin. Therefore, when the output impedance of the reference voltage is too high, it seems as if the AVREF pin and the series resistor string are connected in series. This may cause a greater reference voltage error. (8) AVSS pin This is the ground potential pin of the A/D converter. Always keep it at the same potential as the VSS0 or VSS1 pin even when not using the A/D converter. (9) AVDD pin This is the A/D converter analog power supply pin. Always keep it at the same potential as the VDD0 or VDD1 pin even when not using the A/D converter. (10) ADTRG pin This pin is a pin used to start the A/D converter by hardware. 258 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.3 Registers to Control A/D Converter The following 2 types of registers are used to control the A/D converter. * A/D converter mode register 0 (ADM0) * Analog input channel specification register 0 (ADS0) (1) A/D converter mode register 0 (ADM0) This register sets the conversion time for analog input to be A/D converted, conversion start/stop, and external trigger. ADM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ADM0 to 00H. User's Manual U14046EJ5V0UD 259 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) CHAPTER 13 Figure 13-2. Format of A/D Converter Mode Register 0 (ADM0) Address: FF80H After reset: 00H R/W Symbol <7> <6> 5 4 3 2 1 0 ADM0 ADCS0 TRG0 FR02 FR01 FR00 EGA01 EGA00 0 ADCS0 A/D conversion operation control 0 Stop conversion operation. 1 Enable conversion operation. TRG0 Software start/hardware start selection 0 Software start 1 Hardware start FR02 FR01 Conversion time selectionNote 1 FR00 fX = 8.38 MHz fX = 12 MHzNote 2 0 0 0 144/fX 17.1 s 12.0 s 0 0 1 120/fX 14.3 s 10.0 sNote 4 0 1 0 96/fX 11.4 sNote 3 8.0 sNote 4 1 0 0 72/fX 8.5 sNote 3 6.0 sNote 4 1 0 1 60/fX 7.1 sNote 3 5.0 sNote 4 1 1 0 48/fX 5.7 sNote 3 4.0 sNote 4 Other than above Setting prohibited EGA01 EGA00 External trigger signal, edge specification 0 0 No edge detection 0 1 Falling edge detection 1 0 Rising edge detection 1 1 Both falling and rising edge detection Notes 1. Set the A/D conversion time as follows. * When operated at fX = 12 MHz (VDD = 4.5 to 5.5 V): 12 s or more * When operated at fX = 8.38 MHz (VDD = 4.0 to 5.5 V): 14 s or more 2. Expanded-specification products of PD780024A Subseries only. 3. Setting is prohibited because the A/D conversion time is less than 14 s. 4. Setting is prohibited because the A/D conversion time is less than 12 s. Caution When rewriting FR00 to FR02 to other than the same data, stop A/D conversion operations once prior to performing rewrite. Remark fX: Main system clock oscillation frequency 260 User's Manual U14046EJ5V0UD 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) CHAPTER 13 (2) Analog input channel specification register 0 (ADS0) This register specifies the analog voltage input port for A/D conversion. ADS0 is set by an 8-bit memory manipulation instruction. RESET input clears ADS0 to 00H. Figure 13-3. Format of Analog Input Channel Specification Register 0 (ADS0) Address: FF81H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 ADS0 0 0 0 0 0 ADS02 ADS01 ADS00 ADS02 ADS01 ADS00 0 0 0 ANI0 0 0 1 ANI1 0 1 0 ANI2 0 1 1 ANI3 1 0 0 ANI4 1 0 1 ANI5 1 1 0 ANI6 1 1 1 ANI7 Analog input channel specification User's Manual U14046EJ5V0UD 261 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.4 A/D Converter Operations 13.4.1 Basic operations of A/D converter <1> Select one channel for A/D conversion with analog input channel specification register 0 (ADS0). <2> The voltage input to the selected analog input channel is sampled by the sample & hold circuit. <3> When sampling has been done for a certain time, the sample & hold circuit is placed in the hold state and the input analog voltage is held until the A/D conversion operation is ended. <4> Bit 7 of the successive approximation register (SAR) is set. The series resistor string voltage tap is set to (1/2) AVREF by the tap selector. <5> The voltage difference between the series resistor string voltage tap and analog input is compared by the voltage comparator. If the analog input is greater than (1/2) AVREF, the MSB of SAR remains set. If the analog input is smaller than (1/2) AVREF, the MSB is reset. <6> Next, bit 6 of SAR is automatically set, and the operation proceeds to the next comparison. The series resistor string voltage tap is selected according to the preset value of bit 7, as described below. * Bit 7 = 1: (3/4) AVREF * Bit 7 = 0: (1/4) AVREF The voltage tap and analog input voltage are compared and bit 6 of SAR is manipulated as follows. * Analog input voltage Voltage tap: Bit 6 = 1 * Analog input voltage < Voltage tap: Bit 6 = 0 <7> Comparison is continued in this way up to bit 0 of SAR. <8> Upon completion of the comparison of 8 bits, an effective digital result value remains in SAR, and the result value is transferred to and latched in A/D conversion result register 0 (ADCR0). At the same time, the A/D conversion end interrupt request (INTAD0) can also be generated. Cautions 1. The first A/D conversion value immediately after A/D conversion has been started may not satisfy the rated value. Take measures such as polling the A/D conversion end interrupt request (INTAD0) and removing the first conversion results. 2. The A/D converter stops operation in standby mode. 262 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Figure 13-4. Basic Operation of 8-Bit A/D Converter Setting ADCS0 to 1, external trigger, or overwriting ADS0 A/D conversion start delay time Conversion time Sampling time A/D converter operation Sampling SAR Undefined A/D conversion 80H C0H or 40H Conversion result Conversion result ADCR0 INTAD0 ADCS0 A/D conversion operations are performed continuously until bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) is reset (0) by software. RESET input clears A/D conversion result register 0 (ADCR0) to 00H. Confirm the conversion results by referring to the A/D conversion end interrupt request flag (ADIF0). The sampling time of the A/D converter varies depending on the values set in A/D converter mode register 0 (ADM0). There is a delay time from when the A/D converter is enabled for operation until sampling is actually performed. For the sets in which a strict A/D conversion time is required, note the contents described in Table 13-2. User's Manual U14046EJ5V0UD 263 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Table 13-2. Sampling Time and A/D Conversion Start Delay Time of A/D Converter FR02 FR01 FR00 Conversion TimeNote 1 Sampling Time A/D Conversion Start Delay Time MIN. 0 0 0 144/fX 20/fX 0 0 1 120/fX 16/fX 0 1 0 96/fX 12/fX 1 0 0 72/fX 10/fX 1 0 1 60/fX 8/fX 1 1 0 48/fX 6/fX Other than above Setting prohibited 0.5/fCPU + 6/fX 0.5/fCPU + 8/fX 0.5/fCPU + 3/fX 0.5/fCPU + 4/fX - - Notes 1. Set the A/D conversion time as follows. * When operated at fX = 12 MHzNote 2 (VDD = 4.5 to 5.5 V): 12 s or more * When operated at fX = 8.38 MHz (VDD = 4.0 to 5.5 V): 14 s or more 2. Expanded-specification products of PD780024A Subseries only. Remark fX: Main system clock oscillation frequency fCPU: CPU clock frequency 264 User's Manual U14046EJ5V0UD MAX. - CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.4.2 Input voltage and conversion results The relationship between the analog input voltage input to the analog input pins (ANI0 to ANI7) and the theoretical A/D conversion result (stored in A/D conversion result register 0 (ADCR0)) is shown by the following expression. ADCR0 = INT ( VIN AVREF x 256 + 0.5) or (ADCR0 - 0.5) x where, INT( ): AVREF 256 VIN < (ADCR0 + 0.5) x AVREF 256 Function which returns integer part of value in parentheses VIN: Analog input voltage AVREF: AVREF pin voltage ADCR0: A/D conversion result register 0 (ADCR0) value Figure 13-5 shows the relationship between the analog input voltage and the A/D conversion result. Figure 13-5. Relationship Between Analog Input Voltage and A/D Conversion Result 255 254 253 A/D conversion result (ADCR0) 3 2 1 0 1 3 2 5 3 1 512 256 512 256 512 256 507 254 509 255 511 512 256 512 256 512 1 Input voltage/AVREF User's Manual U14046EJ5V0UD 265 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.4.3 A/D converter operation mode Select one analog input channel from among ANI0 to ANI7 using analog input channel specification register 0 (ADS0) to start A/D conversion. A/D conversion can be started in either of the following two ways. * Hardware start: Conversion is started by trigger input (rising edge, falling edge, or both rising and falling edges enabled). * Software start: Conversion is started by setting A/D converter mode register 0 (ADM0). When A/D conversion is complete, the interrupt request signal (INTAD0) is generated. (1) A/D conversion by hardware start When bit 6 (TRG0) and bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) are set to 1, the A/D conversion standby state is set. When the external trigger signal (ADTRG) is input, A/D conversion of the voltage applied to the analog input pin specified by analog input channel specification register 0 (ADS0) starts. Upon the end of A/D conversion, the conversion result is stored in A/D conversion result register 0 (ADCR0), and the interrupt request signal (INTAD0) is generated. After one A/D conversion operation is started and finished, the next conversion operation is not started until a new external trigger signal is input. If ADS0 is rewritten during A/D conversion, the converter suspends A/D conversion and waits for a new external trigger signal to be input. When the external trigger input signal is reinput, A/D conversion is carried out from the beginning. If ADS0 is rewritten during A/D conversion standby, A/D conversion starts when the following external trigger input signal is input. If 1 is written to ADCS0 again during A/D conversion, the A/D conversion in progress is discontinued and a new A/D conversion is started when the next external trigger input signal is input. If 0 is written to ADCS0 during A/D conversion, the A/D conversion operation stops immediately. Caution When P03/INTP3/ADTRG is used as the external trigger input (ADTRG), specify the valid edge using bits 1, 2 (EGA00, EGA01) of A/D converter mode register 0 (ADM0) and set the interrupt mask flag (PMK3) to 1. 266 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Figure 13-6. A/D Conversion by Hardware Start (When Falling Edge Is Specified) ADTRG ADM0 set ADCS0 = 1, TRG0 = 1 A/D conversion Standby state ADCR0 ANIn ADS0 rewrite ANIn ANIn Standby state Standby state ANIn ANIn ANIn ANIm Undefined ANIm ANIm ANIm ANIm INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 User's Manual U14046EJ5V0UD 267 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (2) A/D conversion by software start When bit 6 (TRG0) and bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) are set to 0 and 1, respectively, A/D conversion of the voltage applied to the analog input pin specified by analog input channel specification register 0 (ADS0) starts. Upon the end of the A/D conversion, the conversion result is stored in A/D conversion result register 0 (ADCR0), and the interrupt request signal (INTAD0) is generated. After one A/D conversion operation is started and ended, the next conversion operation is immediately started. A/D conversion operations are repeated until new data is written to ADS0. If ADS0 is rewritten during A/D conversion, the converter suspends A/D conversion and A/D conversion of the newly selected analog input channel is started. If 1 is written to ADCS0 again during A/D conversion, the A/D conversion in progress is discontinued and a new A/D conversion is started. If 0 is written to ADCS0 during A/D conversion, the A/D conversion operation stops immediately. Figure 13-7. A/D Conversion by Software Start ADM0 set ADCS0 = 1, TRG0 = 0 A/D conversion ANIn ADS0 rewrite ANIn ANIn ADCS0 = 0 ANIm ANIm Conversion suspended; Conversion results are not stored ADCR0 ANIn ANIn INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 268 User's Manual U14046EJ5V0UD Undefined Stop ANIm CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.5 How to Read A/D Converter Characteristics Table Here we will explain the special terms unique to A/D converters. (1) Resolution This is the minimum analog input voltage that can be identified. That is, the percentage of the analog input voltage per 1 bit of digital output is called 1LSB (Least Significant Bit). The percentage of 1LSB with respect to the full scale is expressed by %FSR (Full Scale Range). When the resolution is 8 bits, 1LSB = 1/28 = 1/256 = 0.4%FSR Accuracy has no relation to resolution, but is determined by overall error. (2) Overall error This shows the maximum error value between the actual measured value and the theoretical value. Zero scale error, full scale error, integral linearity error, differential linearity error and errors which are combinations of these express overall error. Furthermore, quantization error is not included in overall error in the characteristics table. (3) Quantization error When analog values are converted to digital values, there naturally occurs a 1/2LSB error. In an A/D converter, an analog input voltage in a range of 1/2LSB are converted to the same digital code, so a quantization error cannot be avoided. Furthermore, it is not included in the overall error, zero scale error, full scale error, integral linearity error, and differential linearity error in the characteristics table. Figure 13-8. Overall Error Figure 13-9. Quantization Error 1......1 1......1 Overall error Digital output Digital output Ideal line 1/2LSB Quantization error 1/2LSB 0......0 0......0 AVREF 0 AVREF 0 Analog input User's Manual U14046EJ5V0UD Analog input 269 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) CHAPTER 13 (4) Zero scale error This shows the difference between the actual measured value of the analog input voltage and the theoretical value (1/2LSB) when the digital output changes from 0......000 to 0......001. If the actual measured value is greater than the theoretical value, it shows the difference between the actual measured value of the analog input voltage and the theoretical value (3/2LSB) when the digital output changes from 0......001 to 0......010. (5) Full scale error This shows the difference between the actual measured value of the analog input voltage and the theoretical value (full scale -3/2LSB) when the digital output changes from 1......110 to 1......111. (6) Integral linearity error This shows the degree to which the conversion characteristics deviate from the ideal linear relationship. It expresses the maximum value of the difference between the actual measured value and the ideal straight line when the zero scale error and full scale error are 0. (7) Differential linearity error Although the ideal output width for a given code is 1LSB, this value shows the difference between the actual measured value and the ideal value of the width when outputting a particular code. Figure 13-10. Zero Scale Error Figure 13-11. Full Scale Error Digital output (lower 3 bits) Digital output (lower 3 bits) 111 Ideal line 011 010 001 Zero scale error Full scale error 111 110 101 Ideal line 000 000 0 0 1 2 3 AVREF AVREF-3 AVREF-2 AVREF-1 AVREF Analog input (LSB) Analog input (LSB) Figure 13-12. Integral Linearity Error Figure 13-13. Differential Linearity Error 1......1 1......1 Ideal width of 1LSB Digital output Digital output Ideal line 0......0 0 Integral linearity error AVREF Differential linearity error 0......0 0 Analog input 270 User's Manual U14046EJ5V0UD Analog input AVREF CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (8) Conversion time This expresses the time from when the sampling was started to the time when the digital output was obtained. Sampling time is included in the conversion time in the characteristics table. (9) Sampling time This is the time the analog switch is turned on for the analog voltage to be sampled by the sample & hold circuit. Sampling time Conversion time User's Manual U14046EJ5V0UD 271 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) CHAPTER 13 13.6 A/D Converter Cautions (1) Power consumption in standby mode A/D converter stops operating in the standby mode. At this time, power consumption can be reduced by stopping the conversion operation (by clearing bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) to 0). Figure 13-14 shows the circuit configuration of a series resistor string. Figure 13-14. Circuit Configuration of Series Resistor String AVREF ADCS0 P-ch Series resistor string AVSS (2) Input range of ANI0 to ANI7 The input voltages of ANI0 to ANI7 should be within the specification range. In particular, if a voltage higher than AVREF or lower than AVSS is input (even if within the absolute maximum rating range), the conversion value of that channel will be undefined and the conversion values of other channels may also be affected. (3) Contending operations <1> Contention between A/D conversion result register 0 (ADCR0) write and ADCR0 read by instruction upon the end of conversion ADCR0 read is given priority. After the read operation, the new conversion result is written to ADCR0. <2> Contention between ADCR0 write and external trigger signal input upon the end of conversion The external trigger signal is not accepted during A/D conversion. Therefore, the external trigger signal is not accepted during ADCR0 write. <3> Contention between ADCR0 write and A/D converter mode register 0 (ADM0) write or analog input channel specification register 0 (ADS0) write upon the end of conversion ADM0 or ADS0 write is given priority. ADCR0 write is not performed, nor is the conversion end interrupt request signal (INTAD0) generated. (4) ANI0/P10 to ANI7/P17 <1> The analog input pins (ANI0 to ANI7) also function as input port pins (P10 to P17). When A/D conversion is performed with any of pins ANI0 to ANI7 selected, do not access port 1 while conversion is in progress, as this may reduce the conversion resolution. <2> If digital pulses are applied to the pin adjacent to a pin in the process of A/D conversion, the expected A/D conversion value may not be obtainable due to coupling noise. Therefore, avoid applying pulses to the pin adjacent to a pin undergoing A/D conversion. 272 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (5) AVREF pin input impedance A series resistor string of several tens of k is connected between the AVREF pin and the AVSS pin. Therefore, when the output impedance of the reference voltage is too high, it seems as if the AVREF pin and the series resistor string are connected in series. This may cause a greater reference voltage error. (6) Interrupt request flag (ADIF0) The interrupt request flag (ADIF0) is not cleared even if analog input channel specification register 0 (ADS0) is changed. Therefore, if an analog input pin is changed during A/D conversion, the A/D conversion result and conversion end interrupt request flag for the pre-change analog input may be set just before the ADS0 rewrite. Caution is therefore required since, at this time, when ADIF0 is read immediately just after the ADS0 rewrite, ADIF0 is set despite the fact that the A/D conversion for the post-change analog input has not finished. When A/D conversion is restarted after it is stopped, clear ADIF0 before restart. Figure 13-15. A/D Conversion End Interrupt Request Generation Timing ADM0 rewrite (start of ANIn conversion) A/D conversion ANIn ADCR0 ADS0 rewrite (start of ANIm conversion) ANIn ANIn ADIF is set but ANIm conversion has not finished. ANIm Undefined ANIm ANIm ANIm INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 (7) Conversion results just after A/D conversion start The A/D conversion value immediately after A/D conversion has been started may not satisfy the rated value. Take measures such as polling the A/D conversion end interrupt request (INTAD0) and removing the first conversion results. (8) A/D conversion result register 0 (ADCR0) read operation When A/D converter mode register 0 (ADM0) and analog input channel specification register 0 (ADS0) are written, the contents of ADCR0 may become undefined. Read the conversion result following conversion completion before writing to ADM0 and ADS0. Using a timing other than the above may cause an incorrect conversion result to be read. User's Manual U14046EJ5V0UD 273 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (9) Timing at which A/D conversion result is undefined The A/D conversion value may be undefined if the timing of completion of A/D conversion and the timing of stopping the A/D conversion conflict with each other. Therefore, read the A/D conversion result before stopping the A/D conversion operation. Figure 13-16 shows the timing of reading the conversion result. Figure 13-16. Timing of Reading Conversion Result (When Conversion Result Is Undefined) A/D conversion completes A/D conversion completes Normal conversion result ADCR0 Undefined value INTAD0 ADCS0 Normal conversion result is read. A/D conversion is stopped. Undefined value is read. (10) Notes on board design Locate analog circuits as far away from digital circuits as possible on the board because the analog circuits may be affected by the noise of the digital circuits. In particular, do not cross an analog signal line with a digital signal line, or wire an analog signal line in the vicinity of a digital signal line. Otherwise, the A/D conversion characteristics may be affected by the noise of the digital line. Connect AVSS0 and VSS0 at one location on the board where the voltages are stable. (11) AVDD pin The AVDD pin is the analog circuit power supply pin. It supplies power to the input circuits of the ANI0 to ANI7 pins. Therefore, be sure to apply the same potential as VDD0 to this pin even for applications designed to switch to a backup battery for power supply. Figure 13-17. AVDD Pin Connection AVREF VDD0 Main power supply Capacitor for backup AVDD VSS0 AVSS 274 User's Manual U14046EJ5V0UD CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) (12) AVREF pin Connect a capacitor to the AVREF pin to minimize conversion errors due to noise. If an A/D conversion operation has been stopped and then is started, the voltage applied to the AVREF pin becomes unstable, causing the accuracy of the A/D conversion to drop. To prevent this, also connect a capacitor to the AVREF pin. Figure 13-18 shows an example of connecting a capacitor. Figure 13-18. Example of Connecting Capacitor to AVREF Pin Clamp using a diode with a low VF (0.3 V or lower). AVDD AVREF C1 C2 AVSS Remark C1: 4.7 F to 10 F (reference value) C2: 0.01 F to 0.1 F (reference value) Connect C2 as close to the pin as possible. (13) Internal equivalent circuit of ANI0 to ANI7 pins and permissible signal source impedance To complete sampling within the sampling time with sufficient A/D conversion accuracy, the impedance of the signal source such as a sensor must be sufficiently low. Figure 13-19 shows the internal equivalent circuit of the ANI0 to ANI7 pins. If the impedance of the signal source is high, connect capacitors with a high capacitance to the pins ANI0 to ANI7. An example of this is shown in Figure 13-20. In this case, however, the microcontroller cannot follow an analog signal with a high differential coefficient because a lowpass filter is created. To convert a high-speed analog signal or to convert an analog signal in the scan mode, insert a low-impedance buffer. Figure 13-19. Internal Equivalent Circuit of Pins ANI0 to ANI7 R1 R2 ANIn C1 C2 C3 Remark n = 0 to 7 User's Manual U14046EJ5V0UD 275 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Table 13-3. Resistances and Capacitances of Equivalent Circuit (Reference Values) (TYP.) AVREF R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF Caution The resistances and capacitances in Table 13-3 are not guaranteed values. Figure 13-20. Example of Connection If Signal Source Impedance Is High If a noise of AVREF or higher or AVSS or lower may be generated, clamp using a diode with a low VF (0.3 V or lower). <Sensor internal circuit> Reference voltage input AVREF <Microcontroller internal circuit> Output impedance of sensor R1 ANIn R2 R0 C1 C0 0.1 F C2 C3 C0 Lowpass filter is created. Remark n = 0 to 7 (14) Input impedance of ANI0 to ANI7 pins This A/D converter executes sampling by charging the internal sampling capacitor for approximately 1/10 of the conversion time. Therefore, only the leakage current flows during other than sampling, and the current for charging the capacitor flows during sampling. The input impedance therefore varies and has no meaning. To achieve sufficient sampling, it is recommended that the output impedance of the analog input source be 10 k or less, or attach a capacitor of around 100 pF to the ANI0 to ANI7 pins (see Figure 13-20). 276 User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.1 A/D Converter Functions A/D converter is a 10-bit resolution converter that converts analog inputs into digital signals. It can control up to 8 analog input channels (ANI0 to ANI7). (1) Hardware start Conversion is started by trigger input (ADTRG: rising edge, falling edge, or both rising and falling edges can be specified). (2) Software start Conversion is started by setting A/D converter mode register 0 (ADM0). Select one channel for analog input from ANI0 to ANI7 to start A/D conversion. In the case of hardware start, the A/D converter stops when A/D conversion is completed, and an interrupt request (INTAD0) is generated. In the case of software start, A/D conversion is repeated. Each time as A/D conversion operation ends, an interrupt request (INTAD0) is generated. Caution Although the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY incorporate a 10-bit A/D converter, this converter can be operated as an 8-bit A/D converter by using the device file DF780024. User's Manual U14046EJ5V0UD 277 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) Figure 14-1. 10-Bit A/D Converter Block Diagram Series resistor string ANI0/P10 ANI1/P11 ANI2/P12 ANI3/P13 ANI4/P14 ANI5/P15 ANI6/P16 ANI7/P17 AVDD Voltage comparator Successive approximation register (SAR) Edge detector ADTRG/INTP3/P03 Controller AVREF Tap selector Selector Sample & hold circuit AVSS INTAD0 INTP3 3 Edge detector A/D conversion result register 0 (ADCR0) Note Trigger enable ADS02 ADS01 ADS00 ADCS0 TRG0 FR02 FR01 FR00 EGA01 EGA00 Analog input channel specification register 0 (ADS0) A/D converter mode register 0 (ADM0) Internal bus Note The valid edge of external interrupt is specified by bit 3 of the EGP and EGN registers (see Figure 19-5 Format of External Interrupt Rising Edge Enable Register (EGP), External Interrupt Falling Edge Enable Register (EGN)). 278 User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.2 A/D Converter Configuration The A/D converter consists of the following hardware. Table 14-1. A/D Converter Configuration Item Configuration Analog input 8 channels (ANI0 to ANI7) Hardware trigger input 1 (ADTRG) Registers Successive approximation register (SAR) A/D conversion result register 0 (ADCR0) Control registers A/D converter mode register 0 (ADM0) Analog input channel specification register 0 (ADS0) (1) Successive approximation register (SAR) This register compares the analog input voltage value to the voltage tap (compare voltage) value applied from the series resistor string, and holds the result from the most significant bit (MSB). When up to the least significant bit (LSB) is held (end of A/D conversion), the SAR contents are transferred to A/D conversion result register 0 (ADCR0). (2) A/D conversion result register 0 (ADCR0) This is a 16-bit register that stores the A/D conversion results. The lower 6 bits are fixed to 0. Each time A/ D conversion ends, the conversion result is loaded from the successive approximation register (SAR) and held by this register. The most significant bit (MSB) is stored in ADCR0 first. The higher 8 bits of the conversion results are stored in FF17H. The lower 2 bits of the conversion results are stored in FF16H. ADCR0 is read by a 16-bit memory manipulation instruction. RESET input clears ADCR0 to 0000H. Figure 14-2. Format of A/D Conversion Result Register 0 (ADCR0) Address: FF16H, FF17H After reset: 0000H R FF17H FF16H Symbol ADCR0 Caution 0 0 0 0 0 0 When A/D converter mode register 0 (ADM0) and analog input channel specification register 0 (ADS0) are written, the contents of ADCR0 may become undefined. Read the conversion result following conversion completion before writing to ADM0 and ADS0. Using a timing other than the above may cause an incorrect conversion result to be read. (3) Sample & hold circuit The sample & hold circuit samples the input signal of the analog input pin selected by the selector when A/D conversion is started and holds the sampled analog input voltage value during A/D conversion. User's Manual U14046EJ5V0UD 279 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (4) Voltage comparator The voltage comparator compares the sampled analog input voltage to the series resistor string output voltage. (5) Series resistor string The series resistor string is connected between AVREF and AVSS, and generates the voltage to be compared to the analog input. (6) ANI0 to ANI7 pins These are eight analog input pins used to input analog signals to undergo A/D conversion to the A/D converter. ANI0 to ANI7 are alternate-function pins that can also be used for digital input. Cautions 1. Use ANI0 to ANI7 input voltages within the specification range. If a voltage higher than or equal to AVREF or lower than or equal to AVSS is applied (even if within the absolute maximum rating range), the conversion value of that or equal to channel will be undefined and the conversion values of other channels may also be affected. 2. Analog input (ANI0 to ANI7) pins are alternate-function pins that can also be used as input port pins (P10 to P17). When A/D conversion is performed by selecting any one of ANI0 through ANI7, do not access port 1 during conversion, as this may cause a lower conversion resolution. 3. When a digital pulse is applied to a pin adjacent to the pin in the process of A/D conversion, A/D conversion values may not be obtained as expected due to coupling noise. Thus, do not apply a pulse to a pin adjacent to the pin in the process of A/D conversion. (7) AVREF pin This is the A/D converter reference voltage pin and also the analog power supply pin. It converts signals input to ANI0 to ANI7 into digital signals according to the voltage applied between AVREF and AVSS. Caution A series resistor string of several tens of k is connected between the AVREF and AVSS pins. Therefore, when the output impedance of the reference voltage is too high, it seems as if the AVREF pin and the series resistor string are connected in series. This may cause a greater reference voltage error. (8) AVSS pin This is the ground potential pin of the A/D converter. Always keep it at the same potential as the VSS0 or VSS1 pin even when not using the A/D converter. (9) AVDD pin This is the A/D converter analog power supply pin. Always keep it at the same potential as the VDD0 or VDD1 pin even when not using the A/D converter. (10) ADTRG pin This pin is a pin used to start the A/D converter by hardware. 280 User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.3 Registers to Control A/D Converter The following 2 types of registers are used to control the A/D converter. * A/D converter mode register 0 (ADM0) * Analog input channel specification register 0 (ADS0) (1) A/D converter mode register 0 (ADM0) This register sets the conversion time for analog input to be A/D converted, conversion start/stop, and external trigger. ADM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ADM0 to 00H. User's Manual U14046EJ5V0UD 281 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) CHAPTER 14 Figure 14-3. Format of A/D Converter Mode Register 0 (ADM0) Address: FF80H After reset: 00H R/W Symbol <7> <6> 5 4 3 2 1 0 ADM0 ADCS0 TRG0 FR02 FR01 FR00 EGA01 EGA00 0 ADCS0 A/D conversion operation control 0 Stop conversion operation. 1 Enable conversion operation. TRG0 Software start/hardware start selection 0 Software start 1 Hardware start FR02 FR01 Conversion time selectionNote 1 FR00 fX = 8.38 MHz fX = 12 MHzNote 2 0 0 0 144/fX 17.1 s 12.0 s 0 0 1 120/fX 14.3 s 10.0 sNote 4 0 1 0 96/fX 11.4 sNote 3 8.0 sNote 4 1 0 0 72/fX 8.5 sNote 3 6.0 sNote 4 1 0 1 60/fX 7.1 sNote 3 5.0 sNote 4 1 1 0 48/fX 5.7 sNote 3 4.0 sNote 4 Other than above Setting prohibited EGA01 EGA00 External trigger signal, edge specification 0 0 No edge detection 0 1 Falling edge detection 1 0 Rising edge detection 1 1 Both falling and rising edge detection Notes 1. Set the A/D conversion time as follows. * When operated at fX = 12 MHz (VDD = 4.5 to 5.5 V): 12 s or more * When operated at fX = 8.38 MHz (VDD = 4.0 to 5.5 V): 14 s or more 2. Expanded-specification products of PD780034A Subseries only. 3. Setting is prohibited because the A/D conversion time is less than 14 s. 4. Setting is prohibited because the A/D conversion time is less than 12 s. Caution When rewriting FR00 to FR02 to other than the same data, stop A/D conversion operations once prior to performing rewrite. Remark fX: Main system clock oscillation frequency 282 User's Manual U14046EJ5V0UD 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) CHAPTER 14 (2) Analog input channel specification register 0 (ADS0) This register specifies the analog voltage input port for A/D conversion. ADS0 is set by an 8-bit memory manipulation instruction. RESET input clears ADS0 to 00H. Figure 14-4. Format of Analog Input Channel Specification Register 0 (ADS0) Address: FF81H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 ADS0 0 0 0 0 0 ADS02 ADS01 ADS00 ADS02 ADS01 ADS00 0 0 0 ANI0 0 0 1 ANI1 0 1 0 ANI2 0 1 1 ANI3 1 0 0 ANI4 1 0 1 ANI5 1 1 0 ANI6 1 1 1 ANI7 Analog input channel specification User's Manual U14046EJ5V0UD 283 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.4 A/D Converter Operation 14.4.1 Basic operations of A/D converter <1> Select one channel for A/D conversion with analog input channel specification register 0 (ADS0). <2> The voltage input to the selected analog input channel is sampled by the sample & hold circuit. <3> When sampling has been done for a certain time, the sample & hold circuit is placed in the hold state and the input analog voltage is held until the A/D conversion operation is ended. <4> Bit 9 of the successive approximation register (SAR) is set. The series resistor string voltage tap is set to (1/2) AVREF by the tap selector. <5> The voltage difference between the series resistor string voltage tap and analog input is compared by the voltage comparator. If the analog input is greater than (1/2) AVREF, the MSB of SAR remains set. If the analog input is smaller than (1/2) AVREF, the MSB is reset. <6> Next, bit 8 of SAR is automatically set, and the operation proceeds to the next comparison. The series resistor string voltage tap is selected according to the preset value of bit 9, as described below. * Bit 9 = 1: (3/4) AVREF * Bit 9 = 0: (1/4) AVREF The voltage tap and analog input voltage are compared and bit 8 of SAR is manipulated as follows. * Analog input voltage Voltage tap: Bit 8 = 1 * Analog input voltage < Voltage tap: Bit 8 = 0 <7> Comparison is continued in this way up to bit 0 of SAR. <8> Upon completion of the comparison of 10 bits, an effective digital result value remains in SAR, and the result value is transferred to and latched in A/D conversion result register 0 (ADCR0). At the same time, the A/D conversion end interrupt request (INTAD0) can also be generated. Cautions 1. The first A/D conversion value immediately after A/D conversion has been started may not satisfy the rated value. Take measures such as polling the A/D conversion end interrupt request (INTAD0) and removing the first conversion results. 2. The A/D converter stops operation in standby mode. 284 User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) Figure 14-5. Basic Operation of 10-Bit A/D Converter Setting ADCS0 to 1, external trigger, or overwriting ADS0 A/D conversion start delay time Conversion time Sampling time A/D converter operation Sampling SAR Undefined A/D conversion 200H 300H or 100H Conversion result Conversion result ADCR0 INTAD0 ADCS0 A/D conversion operations are performed continuously until bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) is reset (0) by software. RESET input clears A/D conversion result register 0 (ADCR0) to 00H. Confirm the conversion results by referring to the A/D conversion end interrupt request flag (ADIF0). The sampling time of the A/D converter varies depending on the values set in A/D converter mode register 0 (ADM0). There is a delay time from when the A/D converter is enabled for operation until sampling is actually performed. For the sets in which a strict A/D conversion time is required, note the contents described in Table 14-2. User's Manual U14046EJ5V0UD 285 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) Table 14-2. Sampling Time and A/D Conversion Start Delay Time of A/D Converter FR02 FR01 FR00 Conversion TimeNote 1 Sampling Time A/D Conversion Start Delay Time MIN. 0 0 0 144/fX 20/fX 0 0 1 120/fX 16/fX 0 1 0 96/fX 12/fX 1 0 0 72/fX 10/fX 1 0 1 60/fX 8/fX 1 1 0 48/fX 6/fX Other than above Setting prohibited 0.5/fCPU + 6/fX 0.5/fCPU + 8/fX 0.5/fCPU + 3/fX 0.5/fCPU + 4/fX - - Notes 1. Set the A/D conversion time as follows. * When operated at fX = 12 MHzNote 2 (VDD = 4.5 to 5.5 V): 12 s or more * When operated at fX = 8.38 MHz (VDD = 4.0 to 5.5 V): 14 s or more 2. Expanded-specification products of PD780034A Subseries only. Remark fX: Main system clock oscillation frequency fCPU: CPU clock frequency 286 User's Manual U14046EJ5V0UD MAX. - CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.4.2 Input voltage and conversion results The relationship between the analog input voltage input to the analog input pins (ANI0 to ANI7) and the theoretical A/D conversion result (stored in A/D conversion result register 0 (ADCR0)) is shown by the following expression. ADCR0 = INT ( VIN AVREF x 1024 + 0.5) or (ADCR0 - 0.5) x where, INT( ): AVREF VIN < (ADCR0 + 0.5) x 1024 AVREF 1024 Function which returns integer part of value in parentheses VIN: Analog input voltage AVREF: AVREF pin voltage ADCR0: A/D conversion result register 0 (ADCR0) value Figure 14-6 shows the relationship between the analog input voltage and the A/D conversion result. Figure 14-6. Relationship Between Analog Input Voltage and A/D Conversion Result 1023 x 26 1022 x 26 1021 x 26 A/D conversion result (ADCR0) 3 x 26 2 x 26 1 x 26 0 1 3 2 5 3 1 2048 1024204810242048 1024 2043 1022 2045 1023 2047 1 2048 1024 2048 1024 2048 Input voltage/AVREF User's Manual U14046EJ5V0UD 287 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.4.3 A/D converter operation mode Select one analog input channel from among ANI0 to ANI7 using analog input channel specification register 0 (ADS0) to start A/D conversion. A/D conversion can be started in either of the following two ways. * Hardware start: Conversion is started by trigger input (rising edge, falling edge, or both rising and falling edges enabled). * Software start: Conversion is started by setting A/D converter mode register 0 (ADM0). When A/D conversion is complete, the interrupt request signal (INTAD0) is generated. (1) A/D conversion by hardware start When bit 6 (TRG0) and bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) are set to 1, the A/D conversion standby state is set. When the external trigger signal (ADTRG) is input, A/D conversion of the voltage applied to the analog input pin specified by analog input channel specification register 0 (ADS0) starts. Upon the end of A/D conversion, the conversion result is stored in A/D conversion result register 0 (ADCR0), and the interrupt request signal (INTAD0) is generated. After one A/D conversion operation is started and finished, the next conversion operation is not started until a new external trigger signal is input. If ADS0 is rewritten during A/D conversion, the converter suspends A/D conversion and waits for a new external trigger signal to be input. When the external trigger input signal is reinput, A/D conversion is carried out from the beginning. If ADS0 is rewritten during A/D conversion standby, A/D conversion starts when the following external trigger input signal is input. If 1 is written to ADCS0 again during A/D conversion, the A/D conversion in progress is discontinued and a new A/D conversion is started when the next external trigger input signal is input. If 0 is written to ADCS0 during A/D conversion, the A/D conversion operation stops immediately. Caution When P03/INTP3/ADTRG is used as the external trigger input (ADTRG), specify the valid edge using bits 1, 2 (EGA00, EGA01) of A/D converter mode register 0 (ADM0) and set the interrupt mask flag (PMK3) to 1. Figure 14-7. A/D Conversion by Hardware Start (When Falling Edge Is Specified) ADTRG ADM0 set ADCS0 = 1, TRG0 = 1 A/D conversion Standby state ANIn ADS0 rewrite ANIn ANIn ADCR0 Standby state ANIn ANIn Standby state ANIn INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 288 User's Manual U14046EJ5V0UD ANIm Undefined ANIm ANIm ANIm ANIm CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (2) A/D conversion by software start When bit 6 (TRG0) and bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) are set to 0 and 1, respectively, A/D conversion of the voltage applied to the analog input pin specified by analog input channel specification register 0 (ADS0) starts. Upon the end of the A/D conversion, the conversion result is stored in A/D conversion result register 0 (ADCR0), and the interrupt request signal (INTAD0) is generated. After one A/D conversion operation is started and ended, the next conversion operation is immediately started. A/D conversion operations are repeated until new data is written to ADS0. If ADS0 is rewritten during A/D conversion, the converter suspends A/D conversion and A/D conversion of the new selected analog input channel is started. If 1 is written to ADCS0 again during A/D conversion, the A/D conversion in progress is discontinued and a new A/D conversion is started. If 0 is written to ADCS0 during A/D conversion, the A/D conversion operation stops immediately. Figure 14-8. A/D Conversion by Software Start ADM0 set ADCS0 = 1, TRG0 = 0 A/D conversion ANIn ADS0 rewrite ANIn ANIn ANIm ADCS0 = 0 ANIm Conversion suspended; Conversion results are not stored ADCR0 ANIn ANIn Undefined Stop ANIm INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 User's Manual U14046EJ5V0UD 289 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 14.5 How to Read A/D Converter Characteristics Table Here we will explain the special terms unique to A/D converters. (1) Resolution This is the minimum analog input voltage that can be identified. That is, the percentage of the analog input voltage per 1 bit of digital output is called 1LSB (Least Significant Bit). The percentage of 1LSB with respect to the full scale is expressed by %FSR (Full Scale Range). When the resolution is 10 bits, 1LSB = 1/210 = 1/1024 = 0.098%FSR Accuracy has no relation to resolution, but is determined by overall error. (2) Overall error This shows the maximum error value between the actual measured value and the theoretical value. Zero scale error, full scale error, integral linearity error, differential linearity error and errors which are combinations of these express overall error. Furthermore, quantization error is not included in overall error in the characteristics table. (3) Quantization error When analog values are converted to digital values, there naturally occurs a 1/2LSB error. In an A/D converter, an analog input voltage in a range of 1/2LSB are converted to the same digital code, so a quantization error cannot be avoided. Furthermore, it is not included in the overall error, zero scale error, full scale error, integral linearity error, and differential linearity error in the characteristics table. Figure 14-9. Overall Error Figure 14-10. Quantization Error 1......1 1......1 Overall error Digital output Digital output Ideal line 1/2LSB Quantization error 1/2LSB 0......0 0......0 AVREF 0 290 AVREF 0 Analog input Analog input User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (4) Zero scale error This shows the difference between the actual measured value of the analog input voltage and the theoretical value (1/2LSB) when the digital output changes from 0......000 to 0......001. If the actual measured value is greater than the theoretical value, it shows the difference between the actual measured value of the analog input voltage and the theoretical value (3/2LSB) when the digital output changes from 0......001 to 0......010. (5) Full scale error This shows the difference between the actual measured value of the analog input voltage and the theoretical value (full scale -3/2LSB) when the digital output changes from 1......110 to 1......111. (6) Integral linearity error This shows the degree to which the conversion characteristics deviate from the ideal linear relationship. It expresses the maximum value of the difference between the actual measured value and the ideal straight line when the zero scale error and full scale error are 0. (7) Differential linearity error Although the ideal output width for a given code is 1LSB, this value shows the difference between the actual measured value and the ideal value of the width when outputting a particular code. Figure 14-11. Zero Scale Error Figure 14-12. Full Scale Error Digital output (lower 3 bits) Digital output (lower 3 bits) 111 Ideal line 011 010 001 Zero scale error Full scale error 111 110 101 Ideal line 000 000 0 0 1 2 3 AVREF AVREF-3 AVREF-2 AVREF-1 AVREF Analog input (LSB) Analog input (LSB) Figure 14-13. Integral Linearity Error Figure 14-14. Differential Linearity Error 1......1 1......1 Ideal width of 1LSB Digital output Digital output Ideal line 0......0 0 Integral linearity error AVREF Differential linearity error 0......0 0 Analog input AVREF Analog input User's Manual U14046EJ5V0UD 291 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (8) Conversion time This expresses the time from when the sampling was started to the time when the digital output was obtained. Sampling time is included in the conversion time in the characteristics table. (9) Sampling time This is the time the analog switch is turned on for the analog voltage to be sampled by the sample & hold circuit. Sampling time 292 Conversion time User's Manual U14046EJ5V0UD 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) CHAPTER 14 14.6 A/D Converter Cautions (1) Power consumption in standby mode A/D converter stops operating in the standby mode. At this time, power consumption can be reduced by stopping the conversion operation (by clearing bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) to 0). Figure 14-15 shows the circuit configuration of a series resistor string. Figure 14-15. Circuit Configuration of Series Resistor String AVREF ADCS0 P-ch Series resistor string AVSS (2) Input range of ANI0 to ANI7 The input voltages of ANI0 to ANI7 should be within the specification range. In particular, if a voltage higher than AVREF or lower than AVSS is input (even if within the absolute maximum rating range), the conversion value of that channel will be undefined and the conversion values of other channels may also be affected. (3) Contending operations <1> Contention between A/D conversion result register 0 (ADCR0) write and ADCR0 read by instruction upon the end of conversion ADCR0 read is given priority. After the read operation, the new conversion result is written to ADCR0. <2> Contention between ADCR0 write and external trigger signal input upon the end of conversion The external trigger signal is not accepted during A/D conversion. Therefore, the external trigger signal is not accepted during ADCR0 write. <3> Contention between ADCR0 write and A/D converter mode register 0 (ADM0) write or analog input channel specification register 0 (ADS0) write upon the end of conversion ADM0 or ADS0 write is given priority. ADCR0 write is not performed, nor is the conversion end interrupt request signal (INTAD0) generated. (4) ANI0/P10 to ANI7/P17 <1> The analog input pins (ANI0 to ANI7) also function as input port pins (P10 to P17). When A/D conversion is performed with any of pins ANI0 to ANI7 selected, do not access port 1 while conversion is in progress, as this may reduce the conversion resolution. <2> If digital pulses are applied to the pin adjacent to a pin in the process of A/D conversion, the expected A/D conversion value may not be obtainable due to coupling noise. Therefore, avoid applying pulses to the pin adjacent to a pin undergoing A/D conversion. User's Manual U14046EJ5V0UD 293 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (5) AVREF pin input impedance A series resistor string of several tens of k is connected between the AVREF pin and the AVSS pin. Therefore, when the output impedance of the reference voltage is too high, it seems as if the AVREF pin and the series resistor string are connected in series. This may cause a greater reference voltage error. (6) Interrupt request flag (ADIF0) The interrupt request flag (ADIF0) is not cleared even if analog input channel specification register 0 (ADS0) is changed. Therefore, if an analog input pin is changed during A/D conversion, the A/D conversion result and conversion end interrupt request flag for the pre-change analog input may be set just before the ADS0 rewrite. Caution is therefore required since, at this time, when ADIF0 is read immediately just after the ADS0 rewrite, ADIF0 is set despite the fact that the A/D conversion for the post-change analog input has not finished. When A/D conversion is restarted after it is stopped, clear ADIF0 before restart. Figure 14-16. A/D Conversion End Interrupt Request Generation Timing ADM0 rewrite (start of ANIn conversion) A/D conversion ANIn ADCR0 ADS0 rewrite (start of ANIm conversion) ANIn ANIn ADIF is set but ANIm conversion has not finished. ANIm Undefined ANIm ANIm ANIm INTAD0 Remarks 1. n = 0, 1, ......, 7 2. m = 0, 1, ......, 7 (7) Conversion results just after A/D conversion start The A/D conversion value immediately after A/D conversion has been started may not satisfy the rated value. Take measures such as polling the A/D conversion end interrupt request (INTAD0) and removing the first conversion results. (8) A/D conversion result register 0 (ADCR0) read operation When A/D converter mode register 0 (ADM0) and analog input channel specification register 0 (ADS0) are written, the contents of ADCR0 may become undefined. Read the conversion result following conversion completion before writing to ADM0 and ADS0. Using a timing other than the above may cause an incorrect conversion result to be read. 294 User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (9) Timing at which A/D conversion result is undefined The A/D conversion value may be undefined if the timing of completion of A/D conversion and the timing of stopping the A/D conversion conflict with each other. Therefore, read the A/D conversion result before stopping the A/D conversion operation. Figure 14-17 shows the timing of reading the conversion result. Figure 14-17. Timing of Reading Conversion Result (When Conversion Result Is Undefined) A/D conversion completes A/D conversion completes Normal conversion result ADCR0 Undefined value INTAD0 ADCS0 Normal conversion result is read. A/D conversion is stopped. Undefined value is read. (10) Notes on board design Locate analog circuits as far away from digital circuits as possible on the board because the analog circuits may be affected by the noise of the digital circuits. In particular, do not cross an analog signal line with a digital signal line, or wire an analog signal line in the vicinity of a digital signal line. Otherwise, the A/D conversion characteristics may be affected by the noise of the digital line. Connect AVSS0 and VSS0 at one location on the board where the voltages are stable. (11) AVDD pin The AVDD pin is the analog circuit power supply pin. It supplies power to the input circuits of the ANI0 to ANI7 pins. Therefore, be sure to apply the same potential as VDD0 to this pin even for applications designed to switch to a backup battery for power supply. Figure 14-18. AVDD Pin Connection AVREF VDD0 Main power supply Capacitor for backup AVDD VSS0 AVSS User's Manual U14046EJ5V0UD 295 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) (12) AVREF pin Connect a capacitor to the AVREF pin to minimize conversion errors due to noise. If an A/D conversion operation has been stopped and then is started, the voltage applied to the AVREF pin becomes unstable, causing the accuracy of the A/D conversion to drop. To prevent this, also connect a capacitor to the AVREF pin. Figure 14-19 shows an example of connecting a capacitor. Figure 14-19. Example of Connecting Capacitor to AVREF Pin Clamp using a diode with a low VF (0.3 V or lower). AVDD AVREF C1 C2 AVSS Remark C1: 4.7 F to 10 F (reference value) C2: 0.01 F to 0.1 F (reference value) Connect C2 as close to the pin as possible. (13) Internal equivalent circuit of ANI0 to ANI7 pins and permissible signal source impedance To complete sampling within the sampling time with sufficient A/D conversion accuracy, the impedance of the signal source such as a sensor must be sufficiently low. Figure 14-20 shows the internal equivalent circuit of the ANI0 to ANI7 pins. If the impedance of the signal source is high, connect capacitors with a high capacitance to the pins ANI0 to ANI7. An example of this is shown in Figure 14-21. In this case, however, the microcontroller cannot follow an analog signal with a high differential coefficient because a lowpass filter is created. To convert a high-speed analog signal or to convert an analog signal in the scan mode, insert a low-impedance buffer. Figure 14-20. Internal Equivalent Circuit of Pins ANI0 to ANI7 R1 R2 ANIn C1 C2 Remark n = 0 to 7 296 User's Manual U14046EJ5V0UD C3 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) Table 14-3. Resistances and Capacitances of Equivalent Circuit (Reference Values) (TYP.) AVREF R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF Caution The resistances and capacitances in Table 14-3 are not guaranteed values. Figure 14-21. Example of Connection If Signal Source Impedance Is High If a noise of AVREF or higher or AVSS or lower may be generated, clamp using a diode with a low VF (0.3 V or lower). <Sensor internal circuit> Reference voltage input AVREF <Microcontroller internal circuit> Output impedance of sensor R1 ANIn R2 R0 C1 C0 0.1 F C2 C3 C0 Lowpass filter is created. Remark n = 0 to 7 (14) Input impedance of ANI0 to ANI7 pins This A/D converter executes sampling by charging the internal sampling capacitor for approximately 1/10 of the conversion time. Therefore, only the leakage current flows during other than sampling, and the current for charging the capacitor flows during sampling. The input impedance therefore varies and has no meaning. To achieve sufficient sampling, it is recommended that the output impedance of the analog input source be 10 k or less, or attach a capacitor of around 100 pF to the ANI0 to ANI7 pins (see Figure 14-21). User's Manual U14046EJ5V0UD 297 CHAPTER 15 SERIAL INTERFACE OUTLINE The PD780024A, 780034A Subseries and the PD780024AY, 780034AY Subseries have differences in their serial interfaces. These differences are listed in Table 15-1. Table 15-1. Differences Between PD780024A, 780034A Subseries and PD780024AY, 780034AY Subseries PD780024A, 780034A PD780024AY, 780034AY CHAPTER 16 SIO30 CHAPTER 17 SIO31 - - Item UART0 SIO3 IIC0 298 User's Manual U14046EJ5V0UD Relevant Section CHAPTER 18 CHAPTER 16 16.1 SERIAL INTERFACE UART0 Functions of Serial Interface UART0 Serial interface UART0 has the following three modes. (1) Operation stop mode This mode is used when serial transfers are not performed to reduce power consumption. For details, see 16.4.1 Operation stop mode. (2) Asynchronous serial interface (UART) mode (fixed to LSB first) This mode enables full-duplex operation wherein one byte of data after the start bit is transmitted and received. The on-chip baud rate generator dedicated to UART enables communications using a wide range of selectable baud rates. The communication range is between 1.2 kbps and 131 kbps (when operated at fX = 8.38 MHz). In addition, a baud rate (39 kbps max. (when operated at fX = 1.25 MHz)) can also be defined by dividing the clock input to the ASCK0 pin. The UART baud rate generator can also be used to generate a MIDI-standard baud rate (31.25 kbps). For details, see 16.4.2 Asynchronous serial interface (UART) mode. (3) Infrared data transfer mode For details, see 16.4.3 Infrared data transfer mode. Figure 16-1 shows a block diagram of serial interface UART0. User's Manual U14046EJ5V0UD 299 CHAPTER 16 SERIAL INTERFACE UART0 Figure 16-1. Block Diagram of Serial Interface UART0 Internal bus Asynchronous serial interface mode register 0 (ASIM0) Receive buffer register 0 (RXB0) Receive shift register 0 (RX0) RxD0/P23 TXE0 RXE0 PS01 PS00 CL0 Asynchronous serial interface status register 0 (ASIS0) PE0 FE0 OVE0 SL0 ISRM0 IRDAM0 Transmit shift register 0 (TXS0) TxD0/P24 Output latch (P24) PM24 Receive controller (parity check) INTSER0 INTSR0 Transmit controller (parity addition) INTST0 ASCK0/P25 fX/2 to fX/27 Baud rate generatorNote Note For the configuration of the baud rate generator, see Figure 16-2. Figure 16-2. Block Diagram of Baud Rate Generator Start bit sampling clock 5-bit counter Transmit clock 1/2 ASCK0/P25 Selector TXE0 fX/2 to fX/27 Match Encoder Receive clock 1/2 Match 5-bit counter 3 RXE0 Start bit detection 4 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 Baud rate generator control register 0 (BRGC0) Internal bus Remark TXE0: Bit 7 of asynchronous serial interface mode register 0 (ASIM0) RXE0: Bit 6 of asynchronous serial interface mode register 0 (ASIM0) 300 User's Manual U14046EJ5V0UD CHAPTER 16 16.2 SERIAL INTERFACE UART0 Configuration of Serial Interface UART0 Serial interface UART0 includes the following hardware. Table 16-1. Configuration of Serial Interface UART0 Item Configuration Registers Transmit shift register 0 (TXS0) Receive shift register 0 (RX0) Receive buffer register 0 (RXB0) Asynchronous serial interface status register 0 (ASIS0) Control registers Asynchronous serial interface mode register 0 (ASIM0) Baud rate generator control register 0 (BRGC0) Port mode register 2 (PM2) Port 2 (P2) (1) Transmit shift register 0 (TXS0) This is a register for setting transmit data. Data written to TXS0 is transmitted as serial data. When the data length is set as 7 bits, bits 0 to 6 of the data written to TXS0 are transferred as transmit data. Writing data to TXS0 starts the transmit operation. TXS0 can be written by an 8-bit memory manipulation instruction. It cannot be read. RESET input sets TXS0 to FFH. Caution Do not write to TXS0 during a transmit operation. The same address is assigned to TXS0 and receive buffer register 0 (RXB0), so a read operation reads values from RXB0. (2) Receive shift register 0 (RX0) This register converts serial data input via the RxD0 pin to parallel data. When one byte of data is received at this register, the receive data is transferred to receive buffer register 0 (RXB0). RX0 cannot be manipulated directly by a program. (3) Receive buffer register 0 (RXB0) This register is used to hold receive data. When one byte of data is received, one byte of new receive data is transferred from the receive shift register (RX0). When the data length is set as 7 bits, receive data is sent to bits 0 to 6 of RXB0. In this case, the MSB of RXB0 is always 0. RXB0 can be read by an 8-bit memory manipulation instruction. It cannot be written. RESET input sets RXB0 to FFH. Caution The same address is assigned to RXB0 and transmit shift register 0 (TXS0), so during a write operation, values are written to TXS0. User's Manual U14046EJ5V0UD 301 CHAPTER 16 SERIAL INTERFACE UART0 (4) Asynchronous serial interface status register 0 (ASIS0) When a receive error occurs in UART mode, this register indicates the type of error. ASIS0 can be read by an 8-bit memory manipulation instruction. RESET input clears ASIS0 to 00H. Figure 16-3. Format of Asynchronous Serial Interface Status Register 0 (ASIS0) Address: FFA1H After reset: 00H R Symbol 7 6 5 4 3 2 1 0 ASIS0 0 0 0 0 0 PE0 FE0 OVE0 PE0 Parity error flag 0 No parity error 1 Parity error (Transmit data parity not matched) FE0 Framing error flag 0 No framing error 1 Framing errorNote 1 (Stop bit not detected) OVE0 Overrun error flag 0 No overrun error 1 Overrun errorNote 2 (Next receive operation was completed before data was read from receive buffer register 0 (RXB0)) Notes 1. Even if the stop bit length is set to two bits by setting bit 2 (SL0) of asynchronous serial interface mode register 0 (ASIM0), stop bit detection during a receive operation only applies to a stop bit length of 1 bit. 2. When an overrun error has occurred, further overrun errors will continue to occur until the contents of receive buffer register 0 (RXB0) are read. (5) Transmission controller The transmission controller controls transmit operations, such as adding a start bit, parity bit, and stop bit to data that is written to transmit shift register 0 (TXS0), based on the values set to asynchronous serial interface mode register 0 (ASIM0). (6) Reception controller The reception controller controls receive operations based on the values set to asynchronous serial interface mode register 0 (ASIM0). During a receive operation, it performs error checking, such as for parity errors, and sets various values to asynchronous serial interface status register 0 (ASIS0) according to the type of error that is detected. 302 User's Manual U14046EJ5V0UD CHAPTER 16 16.3 SERIAL INTERFACE UART0 Registers to Control Serial Interface UART0 Serial interface UART0 uses the following four registers for control functions. * Asynchronous serial interface mode register 0 (ASIM0) * Baud rate generator control register 0 (BRGC0) * Port mode register 2 (PM2) * Port 2 (P2) (1) Asynchronous serial interface mode register 0 (ASIM0) This is an 8-bit register that controls serial interface UART0's serial transfer operations. ASIM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ASIM0 to 00H. Figure 16-4 shows the format of ASIM0. User's Manual U14046EJ5V0UD 303 CHAPTER 16 SERIAL INTERFACE UART0 Figure 16-4. Format of Asynchronous Serial Interface Mode Register 0 (ASIM0) Address: FFA0H After reset: 00H R/W Symbol <7> <6> 5 4 3 2 1 0 ASIM0 TXE0 RXE0 PS01 PS00 CL0 SL0 ISRM0 IRDAM0 TXE0 RXE0 0 0 0 RxD0/P23 pin function TxD0/P24 pin function Operation stop Port function (P23) Port function (P24) 1 UART mode (receive only) Serial function (RxD0) 1 0 UART mode (transmit only) Port function (P23) 1 1 UART mode (transmit and receive) Serial function (RxD0) PS01 PS00 0 0 No parity 0 1 Zero parity always added during transmission No parity detection during reception (parity errors do not occur) 1 0 Odd parity 1 1 Even parity CL0 Serial function (TxD0) Parity bit specification Character length specification 0 7 bits 1 8 bits SL0 Stop bit length specification for transmit data 0 1 bit 1 2 bits ISRM0 Operation mode Receive completion interrupt control when error occurs 0 Receive completion interrupt request is issued when an error occurs 1 Receive completion interrupt request is not issued when an error occurs IRDAM0 Operation specified for infrared data transfer modeNote 1 0 UART (transmit/receive) mode 1 Infrared data transfer (transmit/receive) modeNote 2 Notes 1. The UART/infrared data transfer mode specification is controlled by TXE0 and RXE0. 2. When using infrared data transfer mode, be sure to set baud rate generator control register 0 (BRGC0) to "10H". Caution 304 Before writing different data to ASIM0, stop operation. User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (2) Baud rate generator control register 0 (BRGC0) This register sets the serial clock for the serial interface. BRGC0 is set by an 8-bit memory manipulation instruction. RESET input clears BRGC0 to 00H. Figure 16-5 shows the format of BRGC0. User's Manual U14046EJ5V0UD 305 CHAPTER 16 SERIAL INTERFACE UART0 Figure 16-5. Format of Baud Rate Generator Control Register 0 (BRGC0) Address: FFA2H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 BRGC0 0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 TPS02 TPS01 TPS00 Source clock selection for 5-bit counter n 0 0 0 External clock input to ASCK0 0 0 0 1 fX/2 1 0 1 0 fX/22 2 0 1 1 fX/23 3 0 fX/24 4 1 fX/25 5 0 fX/26 6 fX/27 7 1 1 1 0 0 1 1 1 1 MDL03 MDL02 MDL01 MDL00 0 0 0 0 0 0 Output clock selection for baud rate generator k 0 fSCK0/16 0 0 1 fSCK0/17 1 0 1 0 fSCK0/18 2 0 0 1 1 fSCK0/19 3 0 1 0 0 fSCK0/20 4 0 1 0 1 fSCK0/21 5 0 1 1 0 fSCK0/22 6 0 1 1 1 fSCK0/23 7 1 0 0 0 fSCK0/24 8 1 0 0 1 fSCK0/25 9 1 0 1 0 fSCK0/26 10 1 0 1 1 fSCK0/27 11 1 1 0 0 fSCK0/28 12 1 1 0 1 fSCK0/29 13 1 1 1 0 fSCK0/30 14 1 1 1 1 Setting prohibited - Cautions 1. Writing to BRGC0 during a communication operation may cause abnormal output from the baud rate generator and disable further communication operations. Therefore, do not write to BRGC0 during a communication operation. 2. Set BRGC0 to 10H when using in infrared data transfer mode. Remarks 1. 2. 3. 4. 5. f X: Main system clock oscillation frequency fSCK0: Source clock for 5-bit counter n: Value set via TPS00 to TPS02 (0 n 7) k: Value set via MDL00 to MDL03 (0 k 14) The equation for the baud rate is as follows. [Baud rate] = 306 fX 2n+1(k + 16) [Hz] User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (3) Port mode register 2 (PM2) Port mode register 2 is used to set input/output of port 2 in 1-bit units. To use the P24/TxD0 pin as a serial data output, clear PM24 and the output latch of P24 to 0. To use the P23/RxD0 pin as a serial data input, and the P25/ASCK0 pin as a clock input, set PM23 and PM25 to 1. At this time, the output latches of P23 and P25 can be either 0 or 1. PM2 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM2 to FFH. Figure 16-6. Format of Port Mode Register 2 (PM2) Address: FF22H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 PM2n I/O mode selection of P2n pin (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD 307 CHAPTER 16 16.4 SERIAL INTERFACE UART0 Operation of Serial Interface UART0 This section explains the three modes of serial interface UART0. 16.4.1 Operation stop mode Because serial transfer is not performed in this mode, the power consumption can be reduced. In addition, pins can be used as ordinary ports. (1) Register to be used Operation stop mode is set by asynchronous serial interface mode register 0 (ASIM0). ASIM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ASIM0 to 00H. Address: FFA0H After reset: 00H R/W Symbol <7> <6> 5 4 3 2 1 0 ASIM0 TXE0 RXE0 PS01 PS00 CL0 SL0 ISRM0 IRDAM0 TXE0 RXE0 0 0 Operation mode Operation stop RxD0/P23 pin function TxD0/P24 pin function Port function (P23) Port function (P24) 16.4.2 Asynchronous serial interface (UART) mode This mode enables full-duplex operation wherein one byte of data after the start bit is transmitted or received. The on-chip baud rate generator dedicated to UART enables communications using a wide range of selectable baud rates. The communication range is between 1.2 kbps and 131 kbps (when operated at fX = 8.38 MHz). The baud rate (39 kbps max. (when operated of fX = 1.25 MHz)) can be defined by dividing the input clock to the ASCK0 pin. The UART baud rate generator can also be used to generate a MIDI-standard baud rate (31.25 kbps). (1) Registers to be used * Asynchronous serial interface mode register 0 (ASIM0) * Asynchronous serial interface status register 0 (ASIS0) * Baud rate generator control register 0 (BRGC0) * Port mode register 2 (PM2) * Port 2 (P2) (a) Asynchronous serial interface mode register 0 (ASIM0) ASIM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ASIM0 to 00H. 308 User's Manual U14046EJ5V0UD CHAPTER 16 Address: FFA0H After reset: 00H SERIAL INTERFACE UART0 R/W Symbol <7> <6> 5 4 3 2 1 0 ASIM0 TXE0 RXE0 PS01 PS00 CL0 SL0 ISRM0 IRDAM0 TXE0 RXE0 0 0 0 RxD0/P23 pin function TxD0/P24 pin function Operation stop Port function (P23) Port function (P24) 1 UART mode (receive only) Serial function (RxD0) 1 0 UART mode (transmit only) Port function (P23) 1 1 UART mode (transmit and receive) Serial function (RxD0) PS01 PS00 0 0 No parity 0 1 Zero parity always added during transmission No parity detection during reception (parity errors do not occur) 1 0 Odd parity 1 1 Even parity CL0 Operation mode Serial function (TxD0) Parity bit specification Character length specification 0 7 bits 1 8 bits SL0 Stop bit length specification for transmit data 0 1 bit 1 2 bits ISRM0 Receive completion interrupt control when error occurs 0 Receive completion interrupt request is issued when an error occurs 1 Receive completion interrupt request is not issued when an error occurs Operation specified for infrared data transfer modeNote 1 IRDAM0 0 UART (transmit/receive) mode 1 Infrared data transfer (transmit/receive) modeNote 2 Notes 1. The UART/infrared data transfer mode specification is controlled by TXE0 and RXE0. 2. When using infrared data transfer mode, be sure to set baud rate generator control register 0 (BRGC0) to 10H. Caution Before writing different data to ASIM0, stop operation. User's Manual U14046EJ5V0UD 309 CHAPTER 16 SERIAL INTERFACE UART0 (b) Asynchronous serial interface status register 0 (ASIS0) ASIS0 can be read by an 8-bit memory manipulation instruction. RESET input clears ASIS0 to 00H. Address: FFA1H After reset: 00H R Symbol 7 6 5 4 3 2 1 0 ASIS0 0 0 0 0 0 PE0 FE0 OVE0 PE0 Parity error flag 0 No parity error 1 Parity error (Transmit data parity not matched) FE0 Framing error flag 0 No framing error 1 Framing errorNote 1 (Stop bit not detected) OVE0 Overrun error flag 0 No overrun error 1 Overrun errorNote 2 (Next receive operation was completed before data was read from receive buffer register 0 (RXB0)) Notes 1. Even if the stop bit length is set to two bits by setting bit 2 (SL0) of asynchronous serial interface mode register 0 (ASIM0), stop bit detection during a receive operation only applies to a stop bit length of 1 bit. 2. When an overrun error has occurred, further overrun errors will continue to occur until the contents of receive buffer register 0 (RXB0) are read. 310 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (c) Baud rate generator control register 0 (BRGC0) BRGC0 is set by an 8-bit memory manipulation instruction. RESET input clears BRGC0 to 00H. Address: FFA2H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 BRGC0 0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 TPS02 TPS01 TPS00 Source clock selection for 5-bit counter n 0 0 0 External clock input to ASCK0 0 0 0 1 fX/2 1 0 1 0 fX/22 2 0 1 1 fX/23 3 0 fX/24 4 1 fX/25 5 0 fX/26 6 fX/27 7 1 1 1 0 0 1 1 1 1 MDL03 MDL02 MDL01 MDL00 0 0 0 0 0 0 Caution Output clock selection for baud rate generator k 0 fSCK0/16 0 0 1 fSCK0/17 1 0 1 0 fSCK0/18 2 0 0 1 1 fSCK0/19 3 0 1 0 0 fSCK0/20 4 0 1 0 1 fSCK0/21 5 0 1 1 0 fSCK0/22 6 0 1 1 1 fSCK0/23 7 1 0 0 0 fSCK0/24 8 1 0 0 1 fSCK0/25 9 1 0 1 0 fSCK0/26 10 1 0 1 1 fSCK0/27 11 1 1 0 0 fSCK0/28 12 1 1 0 1 fSCK0/29 13 1 1 1 0 fSCK0/30 14 1 1 1 1 Setting prohibited - Writing to BRGC0 during a communication operation may cause abnormal output from the baud rate generator and disable further communication operations. Therefore, do not write to BRGC0 during a communication operation. Remarks 1. fX: Main system clock oscillation frequency 2. fSCK0: Source clock for 5-bit counter 3. n: Value set via TPS00 to TPS02 (0 n 7) 4. k: Value set via MDL00 to MDL03 (0 k 14) User's Manual U14046EJ5V0UD 311 CHAPTER 16 SERIAL INTERFACE UART0 The transmit/receive clock that is used to generate the baud rate is obtained by dividing the main system clock. * Transmit/receive clock generation for baud rate by using main system clock The main system clock is divided to generate the transmit/receive clock. The baud rate generated from the main system clock is determined according to the following formula. fX [Baud rate] = 2 n+1 (k + 16) [Hz] fX: Main system clock oscillation frequency When ASCK0 is selected as the source clock of the 5-bit counter, substitute the input clock frequency to the ASCK0 pin for fX in the above expression. n: Value set via TPS00 to TPS02 (0 n 7) k: Value set via MDL00 to MDL03 (0 k 14) Table 16-2. Relationship Between Main System Clock and Baud Rate Error Baud Rate (bps) fX = 8.3886 MHz fX = 8.000 MHz fX = 7.3728 MHz fX = 5.000 MHz fX = 4.1943 MHz BRGC0 ERR (%) BRGC0 ERR (%) BRGC0 ERR (%) BRGC0 ERR (%) BRGC0 ERR (%) 600 - - - - - - - - 7BH 1.14 1200 7BH 1.10 7AH 0.16 78H 0 70H 1.73 6BH 1.14 2400 6BH 1.10 6AH 0.16 68H 0 60H 1.73 5BH 1.14 4800 5BH 1.10 5AH 0.16 58H 0 50H 1.73 4BH 1.14 9600 4BH 1.10 4AH 0.16 48H 0 40H 1.73 3BH 1.14 19200 3BH 1.10 3AH 0.16 38H 0 30H 1.73 2BH 1.14 31250 31H -1.3 30H 0 2DH 1.70 24H 0 21H -1.3 38400 2BH 1.10 2AH 0.16 28H 0 20H 1.73 1BH 1.14 76800 1BH 1.10 1AH 0.16 18H 0 10H 1.73 - - 115200 12H 1.10 11H 2.12 10H 0 - - - - Remark fX: Main system clock oscillation frequency * Error tolerance range for baud rate The error for the baud rate depends on the number of bits per frame and the 5-bit counter's division ratio [1/(16 + k)]. Figure 16-7 shows an example of the baud rate error tolerance range. 312 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 Figure 16-7. Error Tolerance (When k = 0), Including Sampling Errors Ideal sampling point 32T 64T 256T 288T 320T 304T Basic timing START D0 D7 352T 336T P STOP 15.5T High-speed limit timing START D0 30.45T D7 P STOP 60.9T Sampling error 0.5T 304.5T 15.5T Low-speed limit timing START D0 33.55T D7 67.1T Baud rate error tolerance (when k = 0) = 15.5 320 Caution P 301.95T STOP 335.5T x 100 = 4.8438 (%) The above error tolerance value is the value calculated based on the ideal sample point. In the actual design, allow margins that include errors of timing for detecting a start bit. Remark T: 5-bit counter's source clock cycle (d) Port mode register 2 (PM2) Port mode register 2 is used to set input/output of port 2 in 1-bit units. To use the P24/TxD0 pin as a serial data output, clear PM24 and the output latch of P24 to 0. To use the P23/RxD0 pin as a serial data input, and the P25/ASCK0 pin as a clock input, set PM23 and PM25 to 1. At this time, the output latches of P23 and P25 can be either 0 or 1. PM2 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM2 to FFH. Address: FF22H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 PM2n I/O mode selection of P2n pin (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD 313 CHAPTER 16 SERIAL INTERFACE UART0 (2) Communication operations (a) Data format Figure 16-8 shows the format of the transmit/receive data. Figure 16-8. Example of Transmit/Receive Data Format in Asynchronous Serial Interface 1 data frame Start bit D0 D1 D2 D3 D4 D5 D6 D7 Parity bit Stop bit Character bits 1 data frame consists of the following bits. * Start bit ............. 1 bit * Character bits ... 7 bits or 8 bits (LSB first) * Parity bit ........... Even parity, odd parity, zero parity, or no parity * Stop bit(s) ......... 1 bit or 2 bits Asynchronous serial interface mode register 0 (ASIM0) is used to set the character bit length, parity selection, and stop bit length within each data frame. When "7 bits" is selected as the number of character bits, only the lower 7 bits (bits 0 to 6) are valid, so that during a transmission the highest bit (bit 7) is ignored and during reception the highest bit (bit 7) must be cleared to 0. Baud rate generator control register 0 (BRGC0) is used to set the serial transfer rate. If a receive error occurs, information about the receive error can be ascertained by reading asynchronous serial interface status register 0 (ASIS0). 314 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (b) Parity types and operations The parity bit is used to detect bit errors in communication data. Usually, the same type of parity bit is used by the transmitting and receiving sides. When odd parity or even parity is set, errors in the parity bit (the odd-number bit) can be detected. When zero parity or no parity is set, errors are not detected. (i) Even parity * During transmission The number of bits in transmit data that includes a parity bit is controlled so that there are an even number of character bits whose value is 1. The value of the parity bit is as follows. If the transmit data contains an odd number of character bits whose value is 1: the parity bit is "1" If the transmit data contains an even number of character bits whose value is 1: the parity bit is "0" * During reception The number of character bits whose value is 1 is counted in the receive data that includes a parity bit, and a parity error occurs when the counted result is an odd number. (ii) Odd parity * During transmission The number of bits in transmit data that includes a parity bit is controlled so that there is an odd number of character bits whose value is 1. The value of the parity bit is as follows. If the transmit data contains an odd number of character bits whose value is 1: the parity bit is "0" If the transmit data contains an even number of character bits whose value is 1: the parity bit is "1" * During reception The number of character bits whose value is 1 is counted in the receive data that includes a parity bit, and a parity error occurs when the counted result is an even number. (iii) Zero parity During transmission, the parity bit is set to "0" regardless of the transmit data. During reception, the parity bit is not checked. Therefore, no parity errors will occur regardless of whether the parity bit is a "0" or a "1". (iv) No parity No parity bit is added to the transmit data. During reception, receive data is regarded as having no parity bit. Since there is no parity bit, no parity errors will occur. User's Manual U14046EJ5V0UD 315 CHAPTER 16 SERIAL INTERFACE UART0 (c) Transmission The transmit operation is enabled if bit 7 (TXE0) of asynchronous serial interface mode register 0 (ASIM0) is set to 1, and the transmit operation is started when transmit data is written to transmit shift register 0 (TXS0). A start bit, parity bit, and stop bit(s) are automatically added to the data. Starting the transmit operation shifts out the data in TXS0, thereby emptying TXS0, after which a transmit completion interrupt request (INTST0) is issued. The timing of the transmit completion interrupt request is shown in Figure 16-9. Figure 16-9. Timing of Asynchronous Serial Interface Transmit Completion Interrupt Request (i) Stop bit length: 1 bit TxD0 (output) START D0 D1 D2 D6 D7 Parity D0 D1 D2 D6 D7 Parity STOP INTST0 (ii) Stop bit length: 2 bits TxD0 (output) START STOP INTST0 Caution Do not rewrite asynchronous serial interface mode register 0 (ASIM0) during a transmit operation. Rewriting the ASIM0 register during a transmit operation may disable further transmit operations (in such cases, enter a RESET to restore normal operation). 316 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (d) Reception The receive operation performs level detection. The receive operation is enabled when "1" is set to bit 6 (RXE0) of asynchronous serial interface mode register 0 (ASIM0), and the input via the RxD0 pin is sampled. The serial clock specified by baud rate generator control register 0 (BRGC0) is used to sample the RxD0 pin. When the RxD0 pin goes low, the 5-bit counter of the baud rate generator begins counting and the start timing signal for data sampling is output when half of the specified baud rate time has elapsed. If sampling the RxD0 pin input at this start timing signal yields a low-level result, a start bit is recognized, after which the 5-bit counter is initialized and starts counting and data sampling begins. After the start bit is recognized, the character data, parity bit, and one-bit stop bit are detected, at which point reception of one data frame is completed. Once reception of one data frame is completed, the receive data in the shift register is transferred to receive buffer register 0 (RXB0) and INTSR0 (receive completion interrupt request) occurs. If the RXE0 bit is reset (to 0) during a receive operation, the receive operation is stopped immediately. At this time, the contents of RXB0 and ASIS0 do not change, nor does INTSR0 or INTSER0 (receive error interrupt request) occur. Figure 16-10 shows the timing of the asynchronous serial interface receive completion interrupt request. Figure 16-10. Timing of Asynchronous Serial Interface Receive Completion Interrupt Request RxD0 (input) START D0 D1 D2 D6 D7 Parity STOP INTSR0 Caution If the receive operation is enabled with the RxD0 pin input at the low level, the receive operation is immediately started. Make sure the RxD0 pin input is at the high level before enabling the receive operation. User's Manual U14046EJ5V0UD 317 CHAPTER 16 SERIAL INTERFACE UART0 (e) Receive errors Three types of errors can occur during a receive operation: a parity error, framing error, or overrun error. If, as the result of data reception, an error flag is set in asynchronous serial interface status register 0 (ASIS0), a receive error interrupt request (INTSER0) will occur. Receive error interrupt requests are generated before the receive completion interrupt request (INTSR0). Table 16-3 lists the causes behind receive errors. As part of receive error interrupt request (INTSER0) servicing, the contents of ASIS0 can be read to determine which type of error occurred during the receive operation (see Table 16-3 and Figure 16-11). The contents of ASIS0 are reset (to 0) when receive buffer register 0 (RXB0) is read or when the next data is received (if the next data contains an error, its error flag will be set). Table 16-3. Causes of Receive Errors Receive Error Cause ASIS0 Value Parity error Parity specified does not match parity of receive data 04H Framing error Stop bit was not detected 02H Overrun error Reception of the next data was completed before data was read from receive buffer register 0 (RXB0) 01H Figure 16-11. Receive Error Timing RxD0 (input) START D0 D1 D2 D6 D7 Parity STOP INTSR0 Note INTSER0 (When framing/overrun error occurs) INTSER0 (When parity error occurs) Note Even if a receive error occurs when the ISRM0 bit has been set (1), INTSR0 does not occur. Cautions 1. The contents of asynchronous serial interface status register 0 (ASIS0) are reset (to 0) when receive buffer register 0 (RXB0) is read or when the next data is received. To obtain information about the error, be sure to read the contents of ASIS0 before reading RXB0. 2. Be sure to read the contents of receive buffer register 0 (RXB0) after the receive completion interrupt request has occurred even when a receive error has occurred. If RXB0 is not read after the receive completion interrupt request has occurred, overrun errors will occur during the next data receive operations and the receive error status will remain until the contents of RXB0 are read. 318 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 16.4.3 Infrared data transfer mode In infrared data transfer mode, pulses can be output and received in the data format shown in (2). (1) Registers to be used * Asynchronous serial interface mode register 0 (ASIM0) * Asynchronous serial interface status register 0 (ASIS0) * Baud rate generator control register 0 (BRGC0) * Port mode register 2 (PM2) * Port 2 (P2) (a) Asynchronous serial interface mode register 0 (ASIM0) ASIM0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears ASIM0 to 00H. User's Manual U14046EJ5V0UD 319 CHAPTER 16 Address: FFA0H After reset: 00H SERIAL INTERFACE UART0 R/W Symbol <7> <6> 5 4 3 2 1 0 ASIM0 TXE0 RXE0 PS01 PS00 CL0 SL0 ISRM0 IRDAM0 TXE0 RXE0 0 0 0 RxD0/P23 pin function TxD0/P24 pin function Operation stop Port function (P23) Port function (P24) 1 UART mode (receive only) Serial function (RxD0) 1 0 UART mode (transmit only) Port function (P23) 1 1 UART mode (transmit and receive) Serial function (RxD0) PS01 PS00 0 0 No parity 0 1 Zero parity always added during transmission No parity detection during reception (parity errors do not occur) 1 0 Odd parity 1 1 Even parity CL0 Serial function (TxD0) Parity bit specification Character length specification 0 7 bits 1 8 bits SL0 Stop bit length specification for transmit data 0 1 bit 1 2 bits ISRM0 Operation mode Receive completion interrupt control when error occurs 0 Receive completion interrupt request is issued when an error occurs 1 Receive completion interrupt request is not issued when an error occurs IRDAM0 Operation specified for infrared data transfer modeNote 1 0 UART (transmit/receive) mode 1 Infrared data transfer (transmit/receive) modeNote 2 Notes 1. The UART/infrared data transfer mode specification is controlled by TXE0 and RXE0. 2. When using infrared data transfer mode, be sure to set baud rate generator control register 0 (BRGC0) to "10H". Caution 320 Before writing different data to ASIM0, stop operation. User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (b) Asynchronous serial interface status register 0 (ASIS0) ASIS0 can be read by an 8-bit memory manipulation instruction. RESET input clears ASIS0 to 00H. Address: FFA1H After reset: 00H R Symbol 7 6 5 4 3 2 1 0 ASIS0 0 0 0 0 0 PE0 FE0 OVE0 PE0 Parity error flag 0 No parity error 1 Parity error (Transmit data parity not matched) FE0 Framing error flag 0 No framing error 1 Framing errorNote 1 (Stop bit not detected) OVE0 Overrun error flag 0 No overrun error 1 Overrun errorNote 2 (Next receive operation was completed before data was read from receive buffer register 0 (RXB0)) Notes 1. Even if the stop bit length is set to two bits by setting bit 2 (SL0) of asynchronous serial interface mode register 0 (ASIM0), stop bit detection during a receive operation only applies to a stop bit length of 1 bit. 2. When an overrun error has occurred, further overrun errors will continue to occur until the contents of receive buffer register 0 (RXB0) are read. User's Manual U14046EJ5V0UD 321 CHAPTER 16 SERIAL INTERFACE UART0 (c) Baud rate generator control register 0 (BRGC0) BRGC0 is set by an 8-bit memory manipulation instruction. RESET input clears BRGC0 to 00H. Address: FFA2H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 BRGC0 0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 TPS02 TPS01 TPS00 Source clock selection for 5-bit counter n 0 0 0 External clock input to ASCK0 0 0 0 1 fX/2 1 0 1 0 fX/22 2 0 1 1 fX/23 3 0 fX/24 4 1 fX/25 5 0 fX/26 6 fX/27 7 1 0 1 0 1 1 1 1 1 MDL03 MDL02 MDL01 MDL00 0 0 0 0 0 0 Output clock selection for baud rate generator k 0 fSCK0/16 0 0 1 fSCK0/17 1 0 1 0 fSCK0/18 2 0 0 1 1 fSCK0/19 3 0 1 0 0 fSCK0/20 4 0 1 0 1 fSCK0/21 5 0 1 1 0 fSCK0/22 6 0 1 1 1 fSCK0/23 7 1 0 0 0 fSCK0/24 8 1 0 0 1 fSCK0/25 9 1 0 1 0 fSCK0/26 10 1 0 1 1 fSCK0/27 11 1 1 0 0 fSCK0/28 12 1 1 0 1 fSCK0/29 13 1 1 1 0 fSCK0/30 14 1 1 1 1 Setting prohibited - Cautions 1. Writing to BRGC0 during a communication operation may cause abnormal output from the baud rate generator and disable further communication operations. Therefore, do not write to BRGC0 during a communication operation. 2. Set BRGC0 to 10H when using in infrared data transfer mode. Remarks 1. fX: Main system clock oscillation frequency 2. fSCK0: Source clock for 5-bit counter 322 3. n: Value set via TPS00 to TPS02 (0 n 7) 4. k: Value set via MDL00 to MDL03 (0 k 14) User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (d) Port mode register 2 (PM2) Port mode register 2 is used to set input/output of port 2 in 1-bit units. To use the P24/TxD0 pin as a serial data output, clear PM24 and the output latch of P24 to 0. To use the P23/RxD0 pin as a serial data input, and the P25/ASCK0 pin as a clock input, set PM23 and PM25 to 1. At this time, the output latches of P23 and P25 can be either 0 or 1. PM2 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM2 to FFH. Address: FF22H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 PM2n I/O mode selection of P2n pin (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) (2) Data format Figure 16-12 compares the data format used in UART mode with that used in infrared data transfer mode. The IR (infrared) frame corresponds to the bit string of the UART frame, which consists of pulses that include a start bit, eight data bits, and a stop bit. The length of the electrical pulses that are used to transmit and receive in an IR frame is 3/16 the length of the cycle time for one bit (i.e., the "bit time"). This pulse (whose width is 3/16 the length of one bit time) rises from the middle of the bit time (see the figure below). Bit time Pulse width = 3/16 bit time User's Manual U14046EJ5V0UD 323 CHAPTER 16 SERIAL INTERFACE UART0 Figure 16-12. Data Format Comparison Between Infrared Data Transfer Mode and UART Mode UART frame Data bits 0 Start bit 1 D0 0 D1 1 D2 0 D3 0 D4 1 D5 1 D6 0 D7 1 Stop bit IR frame Data bits Start bit 1 0 0 1 0 Stop bit 0 1 1 Bit time 0 1 Pulse width = 3/16 bit time (3) Relationship between main system clock and baud rate Table 16-4 shows the relationship between the main system clock and the baud rate. Table 16-4. Relationship Between Main System Clock and Baud Rate fX = 8.3886 MHz Baud rate 131031 bps fX = 8.000 MHz 125000 bps fX = 7.3728 MHz 115200 bps fX = 5.000 MHz 78125 bps fX = 4.1943 MHz 65536 bps (4) Bit rate and pulse width Table 16-5 lists the bit rate, bit rate error tolerance, and pulse width values. Table 16-5. Bit Rate and Pulse Width Values Bit Rate (kbps) Bit Rate Error Tolerance (% of Bit Rate) Pulse Width Minimum Value (s)Note 2 3/16 Pulse Width <Nominal Value> (s) Maximum Pulse Width (s) 115.2Note 1 +/- 0.87 1.41 1.63 2.71 Notes 1. Operation with fX = 7.3728 MHz 2. When a digital noise eliminator is used in a microcontroller operating at 1.41 MHz or above. Caution When using baud rate generator control register 0 (BRGC0) in infrared data transfer mode, set it to 10H. Remark fX: Main system clock oscillation frequency 324 User's Manual U14046EJ5V0UD CHAPTER 16 SERIAL INTERFACE UART0 (5) Input data and internal signals * Transmit operation timing UART output data Start bit Stop bit UART (Inverted data) Infrared data transfer enable signal TxD0 pin output signal * Receive operation timing Data reception is delayed for one-half of the specified baud rate. UART transfer data Start bit Stop bit RxD0 input Edge detection Sampling clock Receive rate Conversion data Sampling timing User's Manual U14046EJ5V0UD 325 326 Table 16-6. Register Settings (1) Operation stop mode ASIM0 PM23 BRGC0 TXE0 RXE0 PS01 PS00 CL0 SL0 0 0 x x x x P23 PM24 P24 ISRM0 IRDAM0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 x x x x x x x x x x x x x Pin Function Operation P23/RxD0 P24/TxD0 Mode P23 P24 Stop Setting prohibited Other than above (2) Asynchronous serial interface (UART) mode ASIM0 BRGC0 RXE0 PS01 PS00 CL0 SL0 0 1 0/1 0/1 0/1 x P23 PM24 P24 1 x x x ISRM0 IRDAM0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 0/1 0 0/1 0/1 0/1 0/1 0/1 0/1 0/1 Pin Function Operation P24/TxD0 Mode RxD0 P24 Receive Transmit Transmit /receive 1 0 0/1 0/1 0/1 0/1 x 0 0/1 0/1 0/1 0/1 0/1 0/1 0/1 x x 0 0 P23 TxD0 1 1 0/1 0/1 0/1 0/1 0/1 0 0/1 0/1 0/1 0/1 0/1 0/1 0/1 1 x 0 0 RxD0 TxD0 Other than above Setting prohibited (3) Infrared data transfer mode ASIM0 TXE0 RXE0 PS01 PS00 BRGC0 CL0 SL0 PM23 P23 PM24 P24 x x x ISRM0 IRDAM0 TPS02 TPS01 TPS00 MDL03 MDL02 MDL01 MDL00 Pin Function P23/RxD0 Operation P24/TxD0 Mode 0 1 0/1 0/1 0/1 x 0/1 1 0 0 1 0 0 0 0 1 RxD0 P24 Receive 1 0 0/1 0/1 0/1 0/1 x 1 0 0 1 0 0 0 0 x x 0 0 P23 TxD0 0 1 x 0 0 RxD0 Transmit Transmit /receive 1 1 0/1 0/1 0/1 0/1 0/1 1 0 0 1 0 0 0 Other than above Caution When using the infrared data transfer mode, set the BRGC0 register to 10H. Remark x: Don't care, ASIM0: Asynchronous serial interface mode register 0 BRGC0: Baud rate generator control register 0, PMXX: Port mode register, PXX: Output latch of port TxD0 Setting prohibited SERIAL INTERFACE UART0 User's Manual U14046EJ5V0UD P23/RxD0 CHAPTER 16 TXE0 PM23 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 The PD780024A, 780034A Subseries products have two 3-wire serial I/O mode channels (SIO30, SIO31). The PD780024AY, 780034AY Subseries products have one 3-wire serial I/O mode channel (SIO30). 17.1 Functions of Serial Interfaces SIO30 and SIO31 Serial interface SIO3n has the following two modes. (1) Operation stop mode This mode is used when serial transfers are not performed. For details, see 17.4.1 Operation stop mode. (2) 3-wire serial I/O mode (fixed as MSB first) This is an 8-bit data transfer mode using three lines: a serial clock line (SCK3n), serial output line (SO3n), and serial input line (SI3n). Since simultaneous transmit and receive operations are enabled in 3-wire serial I/O mode, the processing time for data transfers is reduced. The first bit of the serial transferred 8-bit data is fixed as the MSB. 3-wire serial I/O mode is useful for connection to a peripheral IC incorporating a clocked serial interface, a display controller, etc. For details, see 17.4.2 3-wire serial I/O mode. Figure 17-1 shows a block diagram of serial interface SIO3n. Remark n = 0, 1: PD780024A, 780034A Subseries n = 0: PD780024AY, 780034AY Subseries Figure 17-1. Block Diagram of Serial Interface SIO3n Internal bus 8 Serial I/O shift register 3n (SIO3n) SI3nNote SO3nNote Output latch Serial clock counter SCK3nNote Serial clock controller Interrupt request signal generator Selector INTCSI3n fX/23 fX/24 fX/25 Note SI30, SO30, and SCK30 pins are alternate with P20, P21, and P22 pins. SI31, SO31, and SCK31 pins are alternate with P34, P35, and P36 pins. User's Manual U14046EJ5V0UD 327 CHAPTER 17 17.2 SERIAL INTERFACES SIO30 AND SIO31 Configuration of Serial Interfaces SIO30 and SIO31 Serial interface SIO3n consists of the following hardware. Table 17-1. Configuration of Serial Interface SIO3n Item Configuration Register Serial I/O shift register 3n (SIO3n) Control registers Serial operation mode register 3n (CSIM3n) Port mode registers 2, 3 (PM2, PM3) Ports 2, 3 (P2, P3) (1) Serial I/O shift register 3n (SIO3n) This is an 8-bit register that performs parallel-serial conversion and serial transmit/receive (shift operations) synchronized with the serial clock. SIO3n is set by an 8-bit memory manipulation instruction. When 1 is set to bit 7 (CSIE3n) of serial operation mode register 3n (CSIM3n), a serial operation can be started by writing data to or reading data from SIO3n. When transmitting, data written to SIO3n is output to the serial output (SO3n). When receiving, data is read from the serial input (SI3n) and written to SIO3n. RESET input makes SIO3n undefined. Caution Do not access SIO3n during a transfer operation unless the access is triggered by a transfer start (read operation is disabled when MODEn = 0 and write operation is disabled when MODEn = 1). Remark n = 0, 1: PD780024A, 780034A Subseries n = 0: 328 PD780024AY, 780034AY Subseries User's Manual U14046EJ5V0UD CHAPTER 17 17.3 SERIAL INTERFACES SIO30 AND SIO31 Registers to Control Serial Interfaces SIO30 and SIO31 Serial interface SIO3n is controlled by the following three registers. * Serial operation mode register 3n (CSIM3n) * Port mode registers 2, 3 (PM2, PM3) * Ports 2, 3 (P2, P3) (1) Serial operation mode register 3n (CSIM3n) This register is used to enable or disable SIO3n's serial clock, operation modes, and specific operations. CSIM3n is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears CSIM3n to 00H. Remark n = 0, 1: PD780024A, 780034A Subseries n = 0: PD780024AY, 780034AY Subseries User's Manual U14046EJ5V0UD 329 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 Figure 17-2. Format of Serial Operation Mode Register 30 (CSIM30) Address: FFB0H After reset: 00H R/W Symbol <7> 6 5 4 3 2 1 0 CSIM30 CSIE30 0 0 0 0 MODE0 SCL301 SCL300 CSIE30 Enable/disable specification for SIO30 Shift register operation Serial counter Port 0 Operation stopped Clear Port functionNote 1 1 Operation enabled Count operation enable Serial function + port functionNote 2 MODE0 Transfer operation modes and flags Operation mode Transfer start trigger SO30/P21 pin function 0 Transmit/transmit and receive mode Write to SIO30 SO30 1 Receive-only mode Read from SIO30 P21Note 3 SCL301 SCL300 Clock selection fX = 8.38 MHz fX = 12 MHzNote 4 - - 0 0 External clock input to SCK30 0 1 fX/23 1.04 MHz 1.50 MHz 1 0 fX/24 523 kHz 750 kHz 1 fX/25 261 kHz 375 kHz 1 Notes 1. When CSIE30 = 0 (SIO30 operation stopped status), the SI30, SO30, and SCK30 pins can be used as port functions. 2. When CSIE30 = 1 (SIO30 operation enabled status), the SI30 pin can be used as a port pin if only the transmit function is used, and the SO30 pin can be used as a port pin if only the receive-only mode is used. 3. When MODE0 = 1 (receive-only mode), the SO30 pin can be used for port functions. 4. Expanded-specification products of PD780024A, 780034A Subseries only. Caution Do not rewrite the value of CSIM30 during transfer. However, CSIE30 can be rewritten using a 1-bit memory manipulation instruction. Remark fX: Main system clock oscillation frequency 330 User's Manual U14046EJ5V0UD CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 Figure 17-3. Format of Serial Operation Mode Register 31 (CSIM31) Address: FFB8H After reset: 00H R/W Symbol <7> 6 5 4 3 2 1 0 CSIM31 CSIE31 0 0 0 0 MODE1 SCL311 SCL310 CSIE31 Enable/disable specification for SIO31 Shift register operation Serial counter Port 0 Operation stopped Clear Port functionNote 1 1 Operation enabled Count operation enable Serial function + port functionNote 2 MODE1 Transfer operation modes and flags Operation mode Transfer start trigger SO31/P35 pin function 0 Transmit/transmit and receive mode Write to SIO31 SO31 1 Receive-only mode Read from SIO31 P35Note 3 SCL311 SCL310 Clock selection fX = 8.38 MHz fX = 12 MHzNote 4 - - 0 0 External clock input to SCK31 0 1 fX/23 1.04 MHz 1.50 MHz 1 0 fX/24 523 kHz 750 kHz 1 fX/25 261 kHz 375 kHz 1 Notes 1. When CSIE31 = 0 (SIO31 operation stopped status), the SI31, SO31, and SCK31 pins can be used as port functions. 2. When CSIE31 = 1 (SIO31 operation enabled status), the SI31 pin can be used as a port pin if only the transmit function is used, and the SO31 pin can be used as a port pin if only the receive-only mode is used. 3. When MODE1 = 1 (receive-only mode), the SO31 pin can be used for port functions. 4. Expanded-specification products of PD780024A, 780034A Subseries only. Caution Do not rewrite the value of CSIM31 during transfer. However, CSIE31 can be rewritten using a 1-bit memory manipulation instruction. Remark fX: Main system clock oscillation frequency User's Manual U14046EJ5V0UD 331 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 (2) Port mode registers 2, 3 (PM2, PM3) These registers set the input/output of ports 2 and 3 in 1-bit units. To use the P21/SO30 and P35/SO31 pins as serial data output, and the P22/SCK30 and P36/SCK31 pins as clock output, clear PM21, PM35, PM22, PM36, and the output latches of P21, P35, P22, and P36 to 0. To use the P20/SI30 and P34/SI31 pins as serial data input, and the P22/SCK30 and P36/SCK31 pins as clock input, set PM20, PM34, PM22, and PM36 to 1. At this time, the output latches of P20, P34, P22, and P36 can be either 0 or 1. PM2 and PM3 are set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM2 and PM3 to FFH. Figure 17-4. Format of Port Mode Register 2 (PM2) Address: FF22H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 PM2n I/O mode selection of P2n pin (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) Figure 17-5. Format of Port Mode Register 3 (PM3) Address: FF23H After reset: FFH Symbol 7 6 5 4 3 2 1 0 PM3 1 PM36 PM35 PM34 PM33 PM32 PM31 PM30 PM3n 332 R/W I/O mode selection of P3n pin (n = 0 to 6) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD CHAPTER 17 17.4 SERIAL INTERFACES SIO30 AND SIO31 Operations of Serial Interfaces SIO30 and SIO31 This section explains the two modes of serial interface SIO3n. 17.4.1 Operation stop mode Because the serial transfer is not performed during this mode, the power consumption can be reduced. In addition, pins can be used as normal I/O ports. (1) Register settings Operation stop mode is set by serial operation mode register 3n (CSIM3n). CSIM3n is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears CSIM3n to 00H. Address: FFB0H (SIO30), FFB8H (SIO31) After reset: 00H R/W Symbol <7> 6 5 4 3 2 1 0 CSIM3n CSIE3n 0 0 0 0 MODEn SCL3n1 SCL3n0 CSIE3n Enable/disable specification for SIO3n Shift register operation 0 Operation disabled Serial counter Clear Port Port functionNote Note When CSIE3n = 0 (SIO3n operation stop status), the pins SI3n, SO3n, and SCK3n can be used for port functions. Remark n = 0, 1 User's Manual U14046EJ5V0UD 333 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 17.4.2 3-wire serial I/O mode The 3-wire serial I/O mode can be used when connecting a peripheral IC incorporating a clocked serial interface, a display controller, etc. This mode executes data transfers via three lines: a serial clock line (SCK3n), serial output line (SO3n), and serial input line (SI3n). (1) Registers to be used * Serial operation mode register 3n (CSIM3n) * Port mode registers 2, 3 (PM2, PM3) * Ports 2, 3 (P2, P3) (a) Serial operation mode register 3n (CSIM3n) CSIM3n is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears CSIM3n to 00H. Address: FFB0H (SIO30), FFB8H (SIO31) After reset: 00H R/W Symbol <7> 6 5 4 3 2 1 0 CSIM3n CSIE3n 0 0 0 0 MODEn SCL3n1 SCL3n0 CSIE3n Enable/disable specification for SIO3n Shift register operation Serial counter Port 0 Operation stopped Clear Port functionNote 1 1 Operation enabled Count operation enable Serial function + port functionNote 2 MODEn Transfer operation modes and flags Operation mode Transfer start trigger SO3n pin function 0 Transmit/transmit and receive mode Write to SIO3n SO3n 1 Receive-only mode Read from SIO3n Port functionNote 3 SCL3n1 0 0 1 1 SCL3n0 Clock selection fX = 8.38 MHz fX = 12 MHzNote 4 0 External clock input to SCK3n - - 1 fX/23 1.04 MHz 1.50 MHz 0 fX/24 523 kHz 750 kHz 1 fX/25 261 kHz 375 kHz Notes 1. When CSIE3n = 0 (SIO3n operation stopped status), the SI3n, SO3n, and SCK3n pins can be used as port functions. 2. When CSIE3n = 1 (SIO3n operation enabled status), the SI3n pin can be used as a port pin if only the transmit function is used, and the SO3n pin can be used as a port pin if only the receive-only mode is used. 3. When MODEn = 1 (receive-only mode), the SO3n pin can be used for port functions. 4. Expanded-specification products of PD780024A, 780034A Subseries only. 334 User's Manual U14046EJ5V0UD CHAPTER 17 Caution SERIAL INTERFACES SIO30 AND SIO31 Do not rewrite the value of CSIM3n during transfer. However, CSIE3n can be rewritten using a 1-bit memory manipulation instruction. Remarks 1. fX: Main system clock oscillation frequency 2. n = 0, 1: PD780024A, 780034A Subseries n = 0: PD780024AY, 780034AY Subseries (b) Port mode registers 2, 3 (PM2, PM3) These registers set the input/output of ports 2 and 3 in 1-bit units. To use the P21/SO30 and P35/SO31 pins as serial data output, and the P22/SCK30 and P36/SCK31 pins as clock output, clear PM21, PM35, PM22, PM36, and the output latches of P21, P35, P22, and P36 to 0. To use the P20/SI30 and P34/SI31 pins as serial data input, and the P22/SCK30 and P36/SCK31 pins as clock input, set PM20, PM34, PM22, and PM36 to 1. At this time, the output latches of P20, P34, P22, and P36 can be either 0 or 1. PM2 and PM3 are set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM2 and PM3 to FFH. Address: FF22H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM2 1 1 PM25 PM24 PM23 PM22 PM21 PM20 PM2n I/O mode selection of P2n pin (n = 0 to 5) 0 Output mode (output buffer on) 1 Input mode (output buffer off) Address: FF23H After reset: FFH R/W Symbol 7 6 5 4 3 2 1 0 PM3 1 PM36 PM35 PM34 PM33 PM32 PM31 PM30 PM3n I/O mode selection of P3n pin (n = 0 to 6) 0 Output mode (output buffer on) 1 Input mode (output buffer off) (2) Transfer start A serial transfer starts when the following two conditions have been satisfied and transfer data has been set (or read) to serial I/O shift register 3n (SIO3n). <Transfer start conditions> * SIO3n operation control bit (CSIE3n) = 1 * After an 8-bit serial transfer, either the internal serial clock is stopped or SCK3n is set to high level. <Transfer start timing> * Transmit/transmit and receive mode (MODEn = 0) Transfer starts when writing to SIO3n. * Receive-only mode (MODEn = 1) Transfer starts when reading from SIO3n. Caution After data has been written to SIO3n, transfer will not start even if the CSIE3n bit value is set to 1. User's Manual U14046EJ5V0UD 335 CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 (3) Communication operations In the 3-wire serial I/O mode, data is transmitted and received in 8-bit units. Each bit of data is transmitted or received in synchronization with the serial clock. Serial I/O shift register 3n (SIO3n) is shifted in synchronization with the falling edge of the serial clock. Transmit data is held in the SO3n latch and is output from the SO3n pin. Data that is received via the SI3n pin in synchronization with the rising edge of the serial clock is latched to SIO3n. Figure 17-6. Timing of 3-Wire Serial I/O Mode Latched to SIO3n at the SCK3n rising edge SCK3n 1 2 3 4 5 6 7 8 SI3n DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 SO3n DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 CSIIF3n Transfer completion Transfer starts in synchronization with the SCK3n falling edge (4) Transfer complete Completion of an 8-bit transfer automatically stops the serial transfer operation and the interrupt request flag (CSIIF3n) is set. Remark n = 0, 1: PD780024A, 780034A Subseries n = 0: 336 PD780024AY, 780034AY Subseries User's Manual U14046EJ5V0UD (1) Operation stop mode * Serial interface SIO30 Table 17-2. Register Settings CSIM30 CSIE30 MODE0 SCL301 SCL300 0 x x x PM20 P20 PM21 P21 PM22 P22 x x x x x x Pin Function Operation P20/SI30 P21/SO30 P22/SCK30 P20 P21 P22 Stop Setting prohibited Other than above * Serial interface SIO31 CSIM31 MODE1 SCL311 SCL310 0 x x x P34 PM35 P35 PM36 P36 x x x x x x Pin Function Operation P34/SI31 P35/SO31 P36/SCK31 P34 P35 P36 Stop Setting prohibited Other than above CSIM30 CSIE30 MODE0 SCL301 SCL300 1 1 0 0 1 0 1 1 1 0 0 Other than above 0 PM20 P20 PM21 P21 PM22 P22 1 x x x 1 x 1 x 0 0 1 x 1 x x x 0 0 1 x 0 0 0 0 Pin Function Operation P20/SI30 P21/SO30 P22/SCK30 SI30 P21 SCK30 input Slave receive SO30 SCK30 input Slave transmit/transmit and receive P21 SCK30 output Master receive Note SI30 SI30 SI30 Note SCK30 output Master transmit/transmit and receive SO30 Other than above Setting prohibited * Serial interface SIO31 CSIM31 CSIE31 MODE1 SCL311 SCL310 1 1 0 0 1 0 1 1 1 0 0 0 Other than above PM34 P34 PM35 P35 PM36 P36 1 x x x 1 x 1 x 0 0 1 x 1 x x x 0 0 1 x 0 0 Other than above 0 0 Pin Function Operation P21/SI31 P21/SO31 P22/SCK31 SI31 P35 SCK31 input Slave receive SO31 SCK31 input Slave transmit/transmit and receive P35 SCK31 output Master receive Note SI31 SI31 SI31 Note SO31 SCK31 output Master transmit/transmit and receive Setting prohibited 337 Note When using for transmission only, it can be used as P20 or P34. Remark x: Don't care, CSIM30, CSIM31: Serial operation mode registers 30, 31, PMxx: Port mode register, Pxx: Output latch of port SERIAL INTERFACES SIO30 AND SIO31 User's Manual U14046EJ5V0UD (2) 3-wire serial I/O mode * Serial interface SIO30 CHAPTER 17 CSIE31 PM34 CHAPTER 18 18.1 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Functions of Serial Interface IIC0 Serial interface IIC0 has the following two modes. (1) Operation stop mode This mode is used when serial transfers are not performed. It can therefore be used to reduce power consumption. (2) I2C bus mode (multimaster supported) This mode is used for 8-bit data transfers with several devices via two lines: a serial clock (SCL0) line and a serial data bus (SDA0) line. The transfer rate is as follows. * 97.5 kHz (standard mode) or 350 kHz (high-speed mode): When operated at fX = 8.38 MHz This mode complies with the I2C bus format and can output "start condition", "data", and "stop condition" data segments when transmitting via the serial data bus. These data segments are automatically detected by hardware during reception. Since SCL0 and SDA0 are open-drain outputs, the IIC0 requires pull-up resistors for the serial clock line (SCL0) and the serial data bus line (SDA0). Figure 18-1 shows a block diagram of serial interface IIC0. 338 User's Manual U14046EJ5V0UD Figure 18-1. Block Diagram of Serial Interface IIC0 Internal bus MSTS0 ALD0 EXC0 COI0 TRC0 ADKD0 STD0 SPD0 IIC control register 0 (IICC0) SDA0/P32 User's Manual U14046EJ5V0UD Data hold time correction circuit N-ch opendrain output PM32 Output latch (P32) ACK output circuit Wake-up controller ACK detector Start condition detector Stop condition detector SCL0/P33 Noise eliminator Interrupt request signal generator Serial clock counter Serial clock controller N-ch opendrain output PM33 fX Serial clock wait controller Prescaler Output latch (P33) IIC transfer clock select CLD0 DAD0 SMC0 DFC0 CL00 register 0 (IICCL0) 339 Internal bus INTIIC0 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Noise eliminator Slave address IICE0 LREL0 WREL0 SPIE0 WTIM0 ACKE0 STT0 SPT0 register 0 (SVA0) Match signal CLEAR SET SO0 latch IIC shift D Q register 0 (IIC0) CL00 CHAPTER 18 IIC status register 0 (IICS0) CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-2 shows a serial bus configuration example. Figure 18-2. Serial Bus Configuration Example Using I2C Bus +VDD0 +VDD0 Master CPU1 SDA0 Slave CPU1 SCL0 Serial data bus Serial clock SDA0 Master CPU2 Slave CPU2 SCL0 Address 1 Address 0 340 User's Manual U14046EJ5V0UD SDA0 Slave CPU3 SCL0 Address 2 SDA0 Slave IC SCL0 Address 3 SDA0 Slave IC SCL0 Address N CHAPTER 18 18.2 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Configuration of Serial Interface IIC0 Serial interface IIC0 includes the following hardware. Table 18-1. Configuration of Serial Interface IIC0 Item Configuration Registers IIC shift register 0 (IIC0) Slave address register 0 (SVA0) Control registers IIC control register 0 (IICC0) IIC status register 0 (IICS0) IIC transfer clock select register 0 (IICCL0) Port mode register 3 (PM3) Port 3 (P3) (1) IIC shift register 0 (IIC0) IIC0 is used to convert 8-bit serial data to 8-bit parallel data and vice versa in synchronization with the serial clock. IIC0 can be used for both transmission and reception. Write and read operations to IIC0 are used to control the actual transmit and receive operations. IIC0 is set by an 8-bit memory manipulation instruction. RESET input clears IIC0 to 00H. Figure 18-3. Format of IIC Shift Register 0 (IIC0) Address: FF1FH After reset: 00H Symbol 7 6 R/W 5 4 3 2 1 0 IIC0 Caution Do not write data to IIC0 during data transfer. (2) Slave address register 0 (SVA0) This register sets local addresses when in slave mode. SVA0 is set by an 8-bit memory manipulation instruction. RESET input clears SVA0 to 00H. Figure 18-4. Format of Slave Address Register 0 (SVA0) Address: FFABH After reset: 00H Symbol 7 6 R/W 5 4 3 SVA0 2 1 0 0 Note Note Bit 0 is fixed to 0. User's Manual U14046EJ5V0UD 341 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (3) SO0 latch The SO0 latch is used to retain the SDA0 pin's output level. (4) Wake-up controller This circuit generates an interrupt request when the address received by this register matches the address value set to slave address register 0 (SVA0) or when an extension code is received. (5) Prescaler This selects the sampling clock to be used. (6) Serial clock counter This counter counts the serial clocks that are output or input during transmit/receive operations and is used to verify that 8-bit data was transmitted or received. (7) Interrupt request signal generator This circuit controls the generation of interrupt request signals (INTIIC0). An I2C interrupt request is generated following either of two triggers. * Falling of eighth or ninth clock of the serial clock (set by WTIM0 bitNote) * Interrupt request generated when a stop condition is detected (set by SPIE0 bitNote) Note WTIM0 bit: Bit 3 of IIC control register 0 (IICC0) SPIE0 bit: Bit 4 of IIC control register 0 (IICC0) (8) Serial clock controller In master mode, this circuit generates the clock output via the SCL0 pin from a sampling clock. (9) Serial clock wait controller This circuit controls the wait timing. (10) ACK output circuit, stop condition detector, start condition detector, and ACK detector These circuits are used to output and detect various control signals. (11) Data hold time correction circuit This circuit generates the hold time for data corresponding to the falling edge of the serial clock. 342 User's Manual U14046EJ5V0UD CHAPTER 18 18.3 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Registers to Control Serial Interface IIC0 Serial interface IIC0 is controlled by the following five registers. * IIC control register 0 (IICC0) * IIC status register 0 (IICS0) * IIC transfer clock select register 0 (IICCL0) * Port mode register 3 (PM3) * Port 3 (P3) (1) IIC control register 0 (IICC0) This register is used to enable/stop I2C operations, set wait timing, and set other I2C operations. IICC0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears IICC0 to 00H. User's Manual U14046EJ5V0UD 343 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-5. Format of IIC Control Register 0 (IICC0) (1/4) Address: FFA8H After reset: 00H Symbol IICC0 R/W <7> <6> <5> <4> <3> <2> <1> <0> IICE0 LREL0 WREL0 SPIE0 WTIM0 ACKE0 STT0 SPT0 I2C operation enable IICE0 0 Stop operation. Reset IIC status register 0 (IICS0). Stop internal operation. 1 Enable operation. Condition for clearing (IICE0 = 0) Condition for setting (IICE0 = 1) * Cleared by instruction * When RESET is input * Set by instruction LREL0 Exit from communications 0 Normal operation 1 This exits from the current communications operation and sets standby mode. This setting is automatically cleared after being executed. Its uses include cases in which a locally irrelevant extension code has been received. The SCL0 and SDA0 lines go into the high impedance state. The following flags of IIC status register 0 (IICS0) and IIC control register 0 (IICC0) are cleared. * STD0 * ACKD0 * TRC0 * COI0 * EXC0 * MSTS0 * STT0 * SPT0 The standby mode following exit from communications remains in effect until the following communications entry conditions are met. * After a stop condition is detected, restart is in master mode. * An address match or extension code reception occurs after the start condition. Condition for clearing (LREL0 = 0)Note Condition for setting (LREL0 = 1) * Automatically cleared after execution * When RESET is input * Set by instruction WREL0 Cancel wait 0 Do not cancel wait 1 Cancel wait. This setting is automatically cleared after wait is canceled. When WREL0 is set (wait canceled) during the wait period at the ninth clock pulse in the transmission status (TRC0 = 1), the SDA0 line goes into the high impedance state (TRC0 = 0). Condition for clearing (WREL0 = 0)Note Condition for setting (WREL0 = 1) * Automatically cleared after execution * When RESET is input * Set by instruction SPIE0 Enable/disable generation of interrupt request when stop condition is detected 0 Disable 1 Enable Condition for clearing (SPIE0 = 0)Note Condition for setting (SPIE0 = 1) * Cleared by instruction * When RESET is input * Set by instruction Note This flag's signal is invalid when IICE0 = 0. 344 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-5. Format of IIC Control Register 0 (IICC0) (2/4) WTIM0 Control of wait and interrupt request generation 0 Interrupt request is generated at the eighth clock's falling edge. Master mode: After output of eight clocks, clock output is set to low level and wait is set. Slave mode: After input of eight clocks, the clock is set to low level and wait is set for master device. 1 Interrupt request is generated at the ninth clock's falling edge. Master mode: After output of nine clocks, clock output is set to low level and wait is set. Slave mode: After input of nine clocks, the clock is set to low level and wait is set for master device. This bit's setting is invalid during an address transfer and is valid after the transfer is completed. When in master mode, a wait is inserted at the falling edge of the ninth clock during address transfers. For a slave device that has received a local address, a wait is inserted at the falling edge of the ninth clock after an ACK signal is issued. When the slave device has received an extension code, a wait is inserted at the falling edge of the eighth clock. Condition for clearing (WTIM0 = 0)Note Condition for setting (WTIM0 = 1) * Cleared by instruction * When RESET is input * Set by instruction ACKE0 Acknowledgment control 0 Disable acknowledgment. 1 Enable acknowledgment. During the ninth clock period, the SDA0 line is set to low level. However, the ACK is invalid during address transfers and is valid when EXC0 = 1. Condition for clearing (ACKE0 = 0)Note Condition for setting (ACKE0 = 1) * Cleared by instruction * When RESET is input * Set by instruction Note This flag's signal is invalid when IICE0 = 0. User's Manual U14046EJ5V0UD 345 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-5. Format of IIC Control Register 0 (IICC0) (3/4) STT0 Start condition trigger 0 Do not generate a start condition. 1 When bus is released (during STOP mode): Generate a start condition (for starting as master). The SDA0 line is changed from high level to low level and then the start condition is generated. Next, after the rated amount of time has elapsed, SCL0 is changed to low level. When bus is not used: This trigger functions as a start condition reservation flag. When set, it releases the bus and then automatically generates a start condition. Wait status (during master mode): Generate a restart condition after wait is released. Cautions concerning set timing * For master reception: Cannot be set during transfer. Can be set only in the waiting period when ACKE0 has been set to 0 and slave has been notified of final reception. * For master transmission: A start condition may not be generated normally during the ACK period. Therefore, set it during the waiting period. * Cannot be set at the same time as SPT0 Condition for clearing (STT0 = 0) Condition for setting (STT0 = 1) * Cleared by loss in arbitration * Cleared after start condition is generated by master device * Set by instruction * Cleared by LREL0 = 1 (exit from communications) * When IICE0 = 0 (operation stop) * When RESET is input Remark Bit 1 (STT0) is 0 when read after data has been set. 346 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-5. Format of IIC Control Register 0 (IICC0) (4/4) SPT0 Stop condition trigger 0 Stop condition is not generated. 1 Stop condition is generated (termination of master device's transfer). After the SDA0 line goes to low level, either set the SCL0 line to high level or wait until it goes to high level. Next, after the rated amount of time has elapsed, the SDA0 line changes from low level to high level and a stop condition is generated. Cautions concerning set timing * For master reception: Cannot be set during transfer. Can be set only in the waiting period when ACKE0 has been set to 0 and slave has been notified of final reception. * For master transmission: A stop condition cannot be generated normally during the ACK0 period. Therefore, set it during the waiting period. * Cannot be set at the same time as STT0. * SPT0 can be set only when in master mode.Note * When WTIM0 has been set to 0, if SPT0 is set during the wait period that follows output of eight clocks, note that a stop condition will be generated during the high level period of the ninth clock. When a ninth clock must be output, WTIM0 should be changed from 0 to 1 during the wait period following output of eight clocks, and SPT0 should be set during the wait period that follows output of the ninth clock. Condition for clearing (SPT0 = 0) Condition for setting (SPT0 = 1) * Cleared by loss in arbitration * Automatically cleared after stop condition is detected * Set by instruction * Cleared by LREL0 = 1 (exit from communications) * When IICE0 = 0 (operation stop) * When RESET is input Note Set SPT0 only in master mode. However, SPT0 must be set and a stop condition generated before the first stop condition is detected following the switch to the operation enabled status. For details, see 18.5.14 Other cautions. Caution When bit 3 (TRC0) of IIC status register 0 (IICS0) is set to 1, WREL0 is set during the ninth clock and wait is canceled, after which TRC0 is cleared and the SDA0 line is set to high impedance. Remark Bit 0 (SPT0) becomes 0 when it is read after data setting. User's Manual U14046EJ5V0UD 347 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) CHAPTER 18 (2) IIC status register 0 (IICS0) This register indicates the status of I2C. IICS0 is read by a 1-bit or 8-bit memory manipulation instruction. RESET input clears IICS0 to 00H. Figure 18-6. Format of IIC Status Register 0 (IICS0) (1/3) Address: FFA9H After reset: 00H Symbol IICS0 R <7> <6> <5> <4> <3> <2> <1> <0> MSTS0 ALD0 EXC0 COI0 TRC0 ACKD0 STD0 SPD0 MSTS0 Master device status 0 Slave device status or communication standby status 1 Master device communication status Condition for clearing (MSTS0 = 0) Condition for setting (MSTS0 = 1) * * * * * * When a start condition is generated When a stop condition is detected When ALD0 = 1 (arbitration loss) Cleared by LREL0 = 1 (exit from communications) When IICE0 changes from 1 to 0 (operation stop) When RESET is input ALD0 Detection of arbitration loss 0 This status means either that there was no arbitration or that the arbitration result was a "win". 1 This status indicates the arbitration result was a "loss". MSTS0 is cleared. Condition for clearing (ALD0 = 0) Condition for setting (ALD0 = 1) readNote * Automatically cleared after IICS0 is * When IICE0 changes from 1 to 0 (operation stop) * When RESET is input EXC0 * When the arbitration result is a "loss". Detection of extension code reception 0 Extension code was not received. 1 Extension code was received. Condition for clearing (EXC0 = 0) Condition for setting (EXC0 = 1) * * * * * * When the higher 4 bits of the received address data are either "0000" or "1111" (set at the rising edge of the eighth clock). When a start condition is detected When a stop condition is detected Cleared by LREL0 = 1 (exit from communications) When IICE0 changes from 1 to 0 (operation stop) When RESET is input Note This register is also cleared when a bit manipulation instruction is executed for bits other than IICS0. Remark LREL0: Bit 6 of IIC control register 0 (IICC0) IICE0: 348 Bit 7 of IIC control register 0 (IICC0) User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-6. Format of IIC Status Register 0 (IICS0) (2/3) COI0 Detection of matching addresses 0 Addresses do not match. 1 Addresses match. Condition for clearing (COI0 = 0) Condition for setting (COI0 = 1) * * * * * * When the received address matches the local address (slave address register 0 (SVA0)) (set at the rising edge of the eighth clock). When a start condition is detected When a stop condition is detected Cleared by LREL0 = 1 (exit from communications) When IICE0 changes from 1 to 0 (operation stop) When RESET is input TRC0 Detection of transmit/receive status 0 Receive status (other than transmit status). The SDA0 line is set to high impedance. 1 Transmit status. The value in the SO0 latch is enabled for output to the SDA0 line (valid starting at the falling edge of the first byte's ninth clock). Condition for clearing (TRC0 = 0) Condition for setting (TRC0 = 1) <Both master and slave> <Master> * When a stop condition is detected * Cleared by LREL0 = 1 (exit from communications) * When a start condition is generated <Slave> * When IICE0 changes from 1 to 0 (operation stop) * Cleared by WREL0 = 1Note (wait cancel) * When ALD0 changes from 0 to 1 (arbitration loss) * When RESET is input <Master> * When "1" is output to the first byte's LSB (transfer direction specification bit) <Slave> * When a start condition is detected * When "1" is input to the first byte's LSB (transfer direction specification bit) * When "0" is input to the first byte's LSB (transfer direction specification bit) <When not used for communication> Note If the wait status is cleared by setting bit 5 (WREL0) of IIC control register 0 (IICC0) to 1 at the ninth clock when bit 3 (TRC0) of IIC status register 0 (IICS0) is 1, TRC0 is cleared, and the SDA0 line goes into a high-impedance state. Remark LREL0: Bit 6 of IIC control register 0 (IICC0) IICE0: Bit 7 of IIC control register 0 (IICC0) User's Manual U14046EJ5V0UD 349 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-6. Format of IIC Status Register 0 (IICS0) (3/3) ACKD0 Detection of ACK 0 ACK was not detected. 1 ACK was detected. Condition for clearing (ACKD0 = 0) Condition for setting (ACKD0 = 1) * * * * * * After the SDA0 line is set to low level at the rising edge of the SCL0's ninth clock When a stop condition is detected At the rising edge of the next byte's first clock Cleared by LREL0 = 1 (exit from communications) When IICE0 changes from 1 to 0 (operation stop) When RESET is input STD0 Detection of start condition 0 Start condition was not detected. 1 Start condition was detected. This indicates that the address transfer period is in effect. Condition for clearing (STD0 = 0) Condition for setting (STD0 = 1) * When a stop condition is detected * At the rising edge of the next byte's first clock following address transfer * Cleared by LREL0 = 1 (exit from communications) * When IICE0 changes from 1 to 0 (operation stop) * When RESET is input * When a start condition is detected SPD0 Detection of stop condition 0 Stop condition was not detected. 1 Stop condition was detected. The master device's communication was terminated and the bus was released. Condition for clearing (SPD0 = 0) Condition for setting (SPD0 = 1) * At the rising edge of the address transfer byte's first clock following setting of this bit and detection of a start condition * When IICE0 changes from 1 to 0 (operation stop) * When RESET is input * When a stop condition is detected Remark LREL0: Bit 6 of IIC control register 0 (IICC0) IICE0: 350 Bit 7 of IIC control register 0 (IICC0) User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (3) IIC transfer clock select register 0 (IICCL0) This register is used to set the transfer clock for the I2C bus. IICCL0 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears IICCL0 to 00H. Figure 18-7. Format of IIC Transfer Clock Select Register 0 (IICCL0) (1/2) Address: FFAAH After reset: 00H R/WNote Symbol 7 6 <5> <4> 3 2 1 0 IICCL0 0 0 CLD0 DAD0 SMC0 DFC0 0 CL00 CLD0 Detection of SCL0 line level (valid only when IICE0 = 1) 0 SCL0 line was detected at low level. 1 SCL0 line was detected at high level. Condition for clearing (CLD0 = 0) Condition for setting (CLD0 = 1) * When the SCL0 line is at low level * When IICE0 = 0 (operation stop) * When RESET is input * When the SCL0 line is at high level DAD0 Detection of SDA0 line level (valid only when IICE0 = 1) 0 SDA0 line was detected at low level. 1 SDA0 line was detected at high level. Condition for clearing (DAD0 = 0) Condition for setting (DAD0 = 1) * When the SDA0 line is at low level * When IICE0 = 0 (operation stop) * When RESET is input * When the SDA0 line is at high level SMC0 Operation mode switching 0 Operation in standard mode 1 Operation in high-speed mode Condition for clearing (SMC0 = 0) Condition for setting (SMC0 = 1) * Cleared by instruction * When RESET is input * Set by instruction Note Bits 4 and 5 are read-only bits. Remark IICE0: Bit 7 of IIC control register 0 (IICC0) User's Manual U14046EJ5V0UD 351 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) CHAPTER 18 Figure 18-7. Format of IIC Transfer Clock Select Register 0 (IICCL0) (2/2) Control of digital filter operationNote 1 DFC0 0 Digital filter off 1 Digital filter on CL00 Selection of transfer rate Standard mode High-speed mode fX = 8.38 MHz fX = 8.38 MHz kHzNote 2 0 fX/44 190.4 1 fX/86 97.5 kHz fX/24 350 kHz Notes 1. The digital filter can be used when in high-speed mode. The response time is slower when the digital filter is used. 2. The transfer rate in standard mode must not be set when fX is more than 100 kHz. Caution Stop serial transfer once before rewriting CL00 to other than the same value. Remarks 1. fX: Main system clock oscillation frequency 2. The transfer clock does not change in the high-speed mode even if DFC0 is turned on and off. (4) Port mode register 3 (PM3) PM3 is a register that sets the input/output of port 3 in 1-bit units. To use the P32/SDA0 pin as serial data I/O and the P33/SCL0 pin as clock I/O, clear PM32, PM33, and the output latches of P32 and P33 to 0. PM3 is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets PM3 to FFH. Figure 18-8. Format of Port Mode Register 3 (PM3) Address: FF23FH After reset: FFH Symbol 7 6 5 4 3 2 1 0 PM3 1 PM36 PM35 PM34 PM33 PM32 PM31 PM30 PM3n 352 R/W I/O mode selection of P3n pin (n = 0 to 6) 0 Output mode (output buffer on) 1 Input mode (output buffer off) User's Manual U14046EJ5V0UD CHAPTER 18 18.4 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) I2C Bus Mode Functions 18.4.1 Pin configuration The serial clock pin (SCL0) and serial data bus pin (SDA0) are configured as follows. (1) SCL0 ********* This pin is used for serial clock input and output. This pin is an N-ch open-drain output for both master and slave devices. Input is Schmitt input. (2) SDA0 ********* This pin is used for serial data input and output. This pin is an N-ch open-drain output for both master and slave devices. Input is Schmitt input. Since outputs from the serial clock line and the serial data bus line are N-ch open drain outputs, an external pullup resistor is required. Figure 18-9. Pin Configuration Diagram VDD0 Slave device Master device SCL0 SCL0 Clock output (Clock output) VDD0 VSS0 VSS0 (Clock input) Clock input SDA0 SDA0 Data output Data output VSS0 VSS0 Data input Data input User's Manual U14046EJ5V0UD 353 CHAPTER 18 18.5 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) I2C Bus Definitions and Control Methods The following section describes the I2C bus's serial data communication format and the signals used by the I2C bus. Figure 18-10 shows the transfer timing for the "start condition", "data", and "stop condition" output via the I2C bus's serial data bus. Figure 18-10. I2C Bus Serial Data Transfer Timing 1-7 SCL0 8 9 1-7 R/W ACK Data 8 9 1-7 ACK Data 8 9 SDA0 Start Address condition ACK Stop condition The master device outputs the start condition, slave address, and stop condition. The acknowledge signal (ACK) can be output by either the master or slave device (normally, it is output by the device that receives 8-bit data). The serial clock (SCL0) is continuously output by the master device. However, in the slave device, the SCL0's low level period can be extended and a wait can be inserted. 18.5.1 Start conditions A start condition is met when the SCL0 pin is at high level and the SDA0 pin changes from high level to low level. The start conditions for the SCL0 pin and SDA0 pin are signals that the master device outputs to the slave device when starting a serial transfer. When the device is used as a slave, start conditions can be detected. Figure 18-11. Start Conditions H SCL0 SDA0 A start condition is output when bit 1 (STT0) of IIC control register 0 (IICC0) is set (to 1) after a stop condition has been detected (SPD0: Bit 0 = 1 in IIC status register 0 (IICS0)). When a start condition is detected, bit 1 (STD0) of IICS0 is set (to 1). 354 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.2 Addresses The address is defined by the 7 bits of data that follow the start condition. An address is a 7-bit data segment that is output in order to select one of the slave devices that are connected to the master device via the bus lines. Therefore, each slave device connected via the bus lines must have a unique address. The slave devices include hardware that detects the start condition and checks whether or not the 7-bit address data matches the data values stored in slave address register 0 (SVA0). If the address data matches the SVA0 values, the slave device is selected and communicates with the master device until the master device transmits a start condition or stop condition. Figure 18-12. Address SCL0 1 2 3 4 5 6 7 8 SDA0 A6 A5 A4 A3 A2 A1 A0 R/W 9 Address Note INTIIC0 Note INTIIC0 is not issued if data other than a local address or extension code is received during slave device operation. The slave address and the eighth bit, which specifies the transfer direction as described in 18.5.3 Transfer direction specification below, are together written to IIC shift register 0 (IIC0) and are then output. Received addresses are written to IIC0. The slave address is assigned to the higher 7 bits of IIC0. 18.5.3 Transfer direction specification In addition to the 7-bit address data, the master device sends 1 bit that specifies the transfer direction. When this transfer direction specification bit has a value of "0", it indicates that the master device is transmitting data to a slave device. When the transfer direction specification bit has a value of "1", it indicates that the master device is receiving data from a slave device. Figure 18-13. Transfer Direction Specification SCL0 1 2 3 4 5 6 7 8 SDA0 A6 A5 A4 A3 A2 A1 A0 R/W 9 Transfer direction specification Note INTIIC0 Note INTIIC0 is not issued if data other than a local address or extension code is received during slave device operation. User's Manual U14046EJ5V0UD 355 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.4 Acknowledge (ACK) signal The acknowledge (ACK) signal is used by the transmitting and receiving devices to confirm serial data reception. The receiving device returns one ACK signal for each 8 bits of data it receives. The transmitting device normally receives an ACK signal after transmitting 8 bits of data. However, when the master device is the receiving device, it does not output an ACK signal after receiving the final data to be transmitted. The transmitting device detects whether or not an ACK signal is returned after it transmits 8 bits of data. When an ACK signal is returned, the reception is judged as normal and processing continues. If the slave device does not return an ACK signal, the master device outputs either a stop condition or a restart condition and then stops the current transmission. Failure to return an ACK signal may be caused by the following two factors. (a) Reception was not performed normally. (b) The final data was received. When the receiving device sets the SDA0 line to low level during the ninth clock, the ACK signal becomes active (normal receive response). When bit 2 (ACKE0) of IIC control register 0 (IICC0) is set to 1, automatic ACK signal generation is enabled. Transmission of the eighth bit following the 7 address data bits causes bit 3 (TRC0) of IIC status register 0 (IICS0) to be set. When this TRC0 bit's value is "0", it indicates receive mode. Therefore, ACKE0 should be set to 1. When the slave device is receiving (when TRC0 = 0), if the slave device does not need to receive any more data after receiving several bytes, setting ACKE0 to 0 will prevent the master device from starting transmission of the subsequent data. Similarly, when the master device is receiving (when TRC0 = 0) and the subsequent data is not needed and when either a restart condition or a stop condition should therefore be output, setting ACKE0 to 0 will prevent the ACK signal from being returned. This prevents the MSB data from being output via the SDA0 line (i.e., stops transmission) during transmission from the slave device. Figure 18-14. ACK Signal SCL0 1 2 3 4 5 6 7 SDA0 A6 A5 A4 A3 A2 A1 A0 8 9 R/W ACK When the local address is received, an ACK signal is automatically output in sync with the falling edge of the SCL0's eighth clock regardless of the ACKE0 value. No ACK signal is output if the received address is not a local address. The ACK signal output method during data reception is based on the wait timing setting, as described below. * When 8-clock wait is selected: ACK signal is output when ACKE0 is set to 1 before wait cancellation. (WTIM0 = 0) * When 9-clock wait is selected: ACK signal is automatically output at the falling edge of the SCL0's eighth clock (WTIM0 = 1) 356 if ACKE0 has already been set to 1. User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.5 Stop condition When the SCL0 pin is at high level, changing the SDA0 pin from low level to high level generates a stop condition. A stop condition is a signal that the master device outputs to the slave device when serial transfer has been completed. When the device is used as a slave, stop conditions can be detected. Figure 18-15. Stop Condition H SCL0 SDA0 A stop condition is generated when bit 0 (SPT0) of IIC control register 0 (IICC0) is set (to 1). When the stop condition is detected, bit 0 (SPD0) of IIC status register 0 (IICS0) is set (to 1) and INTIIC0 is generated when bit 4 (SPIE0) of IICC0 is set (to 1). User's Manual U14046EJ5V0UD 357 CHAPTER 18 18.5.6 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Wait signal (WAIT) The wait signal (WAIT) is used to notify the communication partner that a device (master or slave) is preparing to transmit or receive data (i.e., is in a wait state). Setting the SCL0 pin to low level notifies the communication partner of the wait status. When wait status has been canceled for both the master and slave devices, the next data transfer can begin. Figure 18-16. Wait Signal (1/2) (1) When master device has a nine-clock wait and slave device has an eight-clock wait (master transmits, slave receives, and ACKE0 = 1) Master Master returns to high impedance but slave is in wait state (low level). IIC0 Wait after output of ninth clock IIC0 data write (cancel wait) SCL0 6 7 8 9 1 2 3 Slave Wait after output of eighth clock FFH is written to IIC0 or WREL0 is set to 1 IIC0 SCL0 ACKE0 H Transfer lines 358 Wait signal from master Wait signal from slave SCL0 6 7 8 SDA0 D2 D1 D0 9 ACK User's Manual U14046EJ5V0UD 1 2 3 D7 D6 D5 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-16. Wait Signal (2/2) (2) When master and slave devices both have a nine-clock wait (master transmits, slave receives, and ACKE0 = 1) Master and slave both wait after output of ninth clock Master IIC0 data write (cancel wait) IIC0 SCL0 6 7 8 9 1 2 3 Slave FFH is written to IIC0 or WREL0 is set to 1 IIC0 SCL0 ACKE0 H Wait signal from master and slave Transfer lines SCL0 6 7 8 9 SDA0 D2 D1 D0 ACK Wait signal from slave 1 D7 2 3 D6 D5 Output according to previously set ACKE0 value Remark ACKE0: Bit 2 of IIC control register 0 (IICC0) WREL0: Bit 5 of IIC control register 0 (IICC0) A wait may be automatically generated depending on the setting of bit 3 (WTIM0) of IIC control register 0 (IICC0). Normally, the receiving side cancels the wait status when bit 5 (WREL0) is set to 1 or when FFH is written to IIC shift register 0 (IIC0), and the transmitting side cancels the wait status when data is written to IIC0. The master device can also cancel the wait status via either of the following methods. * By setting bit 1 (STT0) of IICC0 to 1 * By setting bit 0 (SPT0) of IICC0 to 1 User's Manual U14046EJ5V0UD 359 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.7 Interrupt request (INTIIC0) generation timing and wait control The setting of bit 3 (WTIM0) of IIC control register 0 (IICC0) determines the timing by which INTIIC0 is generated and the corresponding wait control, as shown in Table 18-2. Table 18-2. INTIIC0 Timing and Wait Control WTIM0 During Slave Device Operation During Master Device Operation Address Data Reception Data Transmission Address Data Reception Data Transmission 0 9Notes 1, 2 8Note 2 8Note 2 9 8 8 1 9Notes 1, 2 9Note 2 9Note 2 9 9 9 Notes 1. The slave device's INTIIC0 signal and wait period occurs at the falling edge of the ninth clock only when there is a match with the address set to slave address register 0 (SVA0). At this point, ACK is output regardless of the value set to IICC0's bit 2 (ACKE0). For a slave device that has received an extension code, INTIIC0 occurs at the falling edge of the eighth clock. However, if the address does not match after restart, INTIIC0 is generated at the falling of the 9th clock, but wait does not occur. 2. If the received address does not match the contents of slave address register 0 (SVA0) and extension code is not received, neither INTIIC0 nor a wait occurs. Remark The numbers in the table indicate the number of the serial clock's clock signals. Interrupt requests and wait control are both synchronized with the falling edge of these clock signals. (1) During address transmission/reception * Slave device operation: Interrupt and wait timing are determined depending on the conditions described in Notes 1 and 2 above, regardless of the WTIM0 bit. * Master device operation: Interrupt and wait timing occur at the falling edge of the ninth clock regardless of the WTIM0 bit. (2) During data reception * Master/slave device operation: Interrupt and wait timing are determined according to the WTIM0 bit. (3) During data transmission * Master/slave device operation: Interrupt and wait timing are determined according to the WTIM0 bit. (4) Wait cancellation method The four wait cancellation methods are as follows. * By setting bit 5 (WREL0) of IIC control register 0 (IICC0) to 1 * By writing to the IIC shift register 0 (IIC0) * By setting a start condition (setting bit 1 (STT0) of IICC0 to 1)Note * By setting a stop condition (setting bit 0 (SPT0) of IICC0 to 1)Note Note Master only. When an 8-clock wait has been selected (WTIM0 = 0), the output level of ACK must be determined prior to wait cancellation. 360 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (5) Stop condition detection INTIIC0 is generated when a stop condition is detected. 18.5.8 Address match detection method In I2C bus mode, the master device can select a particular slave device by transmitting the corresponding slave address. Address match can be detected automatically by hardware. An interrupt request (INTIIC0) occurs when a local address has been set to slave address register 0 (SVA0) and when the address set to SVA0 matches the slave address sent by the master device, or when an extension code has been received. 18.5.9 Error detection In I2C bus mode, the status of the serial data bus (SDA0) during data transmission is captured by IIC shift register 0 (IIC0) of the transmitting device, so the IIC0 data prior to transmission can be compared with the transmitted IIC0 data to enable detection of transmission errors. A transmission error is judged as having occurred when the compared data values do not match. 18.5.10 Extension code (1) When the higher 4 bits of the receive address are either "0000" or "1111", the extension code flag (EXC0) is set for extension code reception and an interrupt request (INTIIC0) is issued at the falling edge of the eighth clock. The local address stored in slave address register 0 (SVA0) is not affected. (2) If "111110xx" is set to SVA0 by a 10-bit address transfer and "111110xx" is transferred from the master device, the results are as follows. Note that INTIIC0 occurs at the falling edge of the eighth clock. * Higher four bits of data match: EXC0 = 1Note COI0 = 1Note * Seven bits of data match: Note EXC0: Bit 5 of IIC status register 0 (IICS0) COI0: Bit 4 of IIC status register 0 (IICS0) (3) Since the processing after the interrupt request occurs differs according to the data that follows the extension code, such processing is performed by software. For example, after the extension code is received, if you do not wish to operate the target device as a slave device, you can set bit 6 (LREL0) of IIC control register 0 (IICC0) to 1 to set the standby mode for the next communication operation. Table 18-3. Extension Code Bit Definitions Slave Address R/W Bit Description 0000 000 0 General call address 0000 000 1 Start byte 0000 001 x CBUS address 0000 010 x Address that is reserved for different bus format 1111 0xx x 10-bit slave address specification User's Manual U14046EJ5V0UD 361 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.11 Arbitration When several master devices simultaneously output a start condition (when STT0 is set to 1 before STD0 is set to 1Note), communication among the master devices is performed as the number of clocks are adjusted until the data differs. This kind of operation is called arbitration. When one of the master devices loses in arbitration, an arbitration loss flag (ALD0) in IIC status register 0 (IICS0) is set (1) via the timing by which the arbitration loss occurred, and the SCL0 and SDA0 lines are both set to high impedance, which releases the bus. The arbitration loss is detected based on the timing of the next interrupt request (the eighth or ninth clock, when a stop condition is detected, etc.) and the ALD0 = 1 setting that has been made by software. For details of interrupt request timing, see 18.5.16 Timing of I2C interrupt request (INTIIC0) occurrence. Note STD0: Bit 1 of IIC status register 0 (IICS0) STT0: Bit 1 of IIC control register 0 (IICC0) Figure 18-17. Arbitration Timing Example Master 1 Hi-Z SCL0 Hi-Z SDA0 Master 1 loses arbitration Master 2 SCL0 SDA0 Transfer lines SCL0 SDA0 362 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Table 18-4. Status During Arbitration and Interrupt Request Generation Timing Status During Arbitration Interrupt Request Generation Timing At falling edge of eighth or ninth clock following byte transferNote 1 During address transmission Read/write data after address transmission During extension code transmission Read/write data after extension code transmission During data transmission During ACK signal transfer period after data transmission When restart condition is detected during data transfer When stop condition is detected during data transfer When stop condition is output (when SPIE0 = 1)Note 2 When data is at low level while attempting to output a restart condition At falling edge of eighth or ninth clock following byte transferNote 1 When stop condition is detected while attempting to output a restart condition When stop condition is output (when SPIE0 = 1)Note 2 When data is at low level while attempting to output a stop condition At falling edge of eighth or ninth clock following byte transferNote 1 When SCL0 is at low level while attempting to output a restart condition Notes 1. When WTIM0 (bit 3 of IIC control register 0 (IICC0)) = 1, an interrupt request occurs at the falling edge of the ninth clock. When WTIM0 = 0 and the extension code's slave address is received, an interrupt request occurs at the falling edge of the eighth clock. 2. When there is a chance that arbitration will occur, set SPIE0 = 1 for master device operation. Remark SPIE0: Bit 4 of IIC control register 0 (IICC0) 18.5.12 Wake-up function The I2C bus slave function is a function that generates an interrupt request (INTIIC0) when a local address and extension code have been received. This function makes processing more efficient by preventing unnecessary interrupt requests from occurring when addresses do not match. When a start condition is detected, wake-up standby mode is set. This wake-up standby mode is in effect while addresses are transmitted due to the possibility that an arbitration loss may change the master device (which has output a start condition) to a slave device. However, when a stop condition is detected, bit 4 (SPIE0) of IIC control register 0 (IICC0) is set regardless of the wake-up function, and this determines whether interrupt requests are enabled or disabled. User's Manual U14046EJ5V0UD 363 CHAPTER 18 18.5.13 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Communication reservation To start master device communications when not currently using a bus, a communication reservation can be made to enable transmission of a start condition when the bus is released. There are two modes under which the bus is not used. * When arbitration results in neither master nor slave operation * When an extension code is received and slave operation is disabled (ACK is not returned and the bus was released when bit 6 (LREL0) of IIC control register 0 (IICC0) was set to 1). If bit 1 (STT0) of IICC0 is set (1) while the bus is not used (after a stop condition is detected), a start condition is automatically generated and wait status is set. When the bus release is detected (when a stop condition is detected), writing to IIC shift register 0 (IIC0) causes the master address transfer to start. At this point, bit 4 (SPIE0) of IICC0 should be set (1). When STT0 has been set (1), the operation mode (as start condition or as communication reservation) is determined according to the bus status. * If the bus has been released ........................................... a start condition is generated * If the bus has not been released (standby mode) .......... communication reservation Check whether the communication reservation operates or not by using MSTS0 (bit 7 of IIC status register 0 (IICS0)) after SST0 is set and the wait time elapses. The wait periods, which should be set via software, are listed in Table 18-5. These wait periods can be set via the settings for bits 3 and 0 (SMC0 and CL00) in IIC transfer clock select register 0 (IICCL0). Table 18-5. Wait Periods SMC0 CL00 Wait Period 0 0 26 clocks 0 1 46 clocks 1 0 16 clocks 1 1 Figure 18-18 shows the communication reservation timing. 364 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-18. Communication Reservation Timing SCL0 Program processing STT0 = 1 Hardware processing Communication reservation 1 2 3 4 5 Write to IIC0 Set SPD0 and INTIIC0 6 7 8 9 Set STD0 1 2 3 4 5 6 SDA0 Output by master with bus mastership Remark IIC0: IIC shift register 0 STT0: Bit 1 of IIC control register 0 (IICC0) STD0: Bit 1 of IIC status register 0 (IICS0) SPD0: Bit 0 of IIC status register 0 (IICS0) Communication reservations are accepted via the following timing. After bit 1 (STD0) of IIC status register 0 (IICS0) is set to 1, a communication reservation can be made by setting bit 1 (STT0) of IIC control register 0 (IICC0) to 1 before a stop condition is detected. Figure 18-19. Timing for Accepting Communication Reservations SCL0 SDA0 STD0 SPD0 Standby mode Figure 18-20 shows the communication reservation protocol. User's Manual U14046EJ5V0UD 365 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-20. Communication Reservation Protocol DI SET1 STT0 Define communication reservation Wait Sets STT0 flag (communication reservation) Defines that communication reservation is in effect (defines and sets user flag to any part of RAM) Secures wait period set by software (see Table 18-5) Note (Communication reservation) MSTS0 = 0? Yes Confirmation of communication reservation No (Generate start condition) Cancel communication reservation MOV IIC0, #xxH Clear user flag IIC0 write operation EI Note The communication reservation operation executes a write to IIC shift register 0 (IIC0) when a stop condition interrupt request occurs. Remark STT0: Bit 1 of IIC control register 0 (IICC0) MSTS0: Bit 7 of IIC status register 0 (IICS0) IIC0: IIC shift register 0 18.5.14 Other cautions After a reset, when changing from a mode in which no stop condition has been detected (the bus has not been released) to a master device communication mode, first generate a stop condition to release the bus, then perform master device communication. When using multiple masters, it is not possible to perform master device communication when the bus has not been released (when a stop condition has not been detected). Use the following sequence for generating a stop condition. (a) Set IIC transfer clock select register 0 (IICCL0). (b) Set (1) bit 7 (IICE0) of IIC control register 0 (IICC0). (c) Set (1) bit 0 (SPT0) of IICC0. 366 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.15 Communication operations (1) Master operations The procedure of controlling slave EEPROMTM using the PD780024AY and 780034AY Subseries as the master of the I2C bus is as follows. Figure 18-21. Master Operation Flowchart (1/5) First perform initialization to use I2C. START Set the port that functions alternately as the pins to be used. First set the port in the input mode, and clear the output latch to 0. Set port (mode and data). PM32, PM33 1, P32, P33 0 Set transfer clock. IICCL0 xxH Specify the operation mode, turn on/off the digital filter, and specify the transfer rate. Set IIC control register 0. IICE0 = WTIM0 = 1 Set a 9-clock wait and enable operation. Set port. PM32, PM33 0 Set the port in the output mode to enable output of I2C. Clear the interrupt request of I2C. Clear the mask to enable the interrupt when using the interrupt. Set interrupt. IICIF0, IICMK0 0 Issue stop condition. SPT0 = 1 SPD0 = 1? Yes Issue start condition. STT0 = 1 Issue the stop condition before starting operation, and release the bus. No Wait until the bus is released. If the stop condition is detected, the bus is released and can be used. Declare use of the bus by issuing the start condition. If the stop condition cannot be detected, the chances are the connected pin is driving the bus low. In this case, refer to Remark. A User's Manual U14046EJ5V0UD 367 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-21. Master Operation Flowchart (2/5) A No STD0 = 1? Wait until the start condition is detected and the bus is ready. Yes Transfer slave address. IIC0 address, R/W (0) Specify writing and transfer the address of the slave (EEPROM). No INTIIC0 = 1? Wait until transfer is completed. Yes Clear INTIIC0 to poll INTIIC0 without using an interrupt. Clear INTIIC0. No ACKD0 = 1? If ACK is not sent, it means that the specified slave does not exist. End processing. Yes End (no slave) If a slave does exist, divide the address of EEPROM (2 bytes) into two, and start transmitting the address from the higher byte. Each time transmission is completed, check ACK. Transmit EEPROM higher address. IIC0 EEPROM higher address No INTIIC0 = 1? Yes Clear INTIIC0. No ACKD0 = 1? Yes End (no acknowledgment) Transmit EEPROM lower address. IIC0 EEPROM lower address Transmit the lower address. B 368 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-21. Master Operation Flowchart (3/5) B INTIIC0 = 1? Yes Clear INTIIC0. ACKD0 = 1? No Yes End (no acknowledgment) Transmission? When writing data to EEPROM, continue writing data. When reading data from EEPROM, start reception processing. Prepare data to be written to EEPROM, and transmit it to EEPROM. Each time data has been transmitted, the slave returns ACK. If any error occurs before transmission of the necessary data is completed, ACK may not be returned. In this case, end transfer. In the case of an error, set the error flag as shown on the left, and release the bus. No Yes Reception TRC0 = 1?data. Prepare write Transmit write data. IIC0 Data INTIIC0 = 1? No Yes Clear INTIIC0. End ACKD0 = 1? No Yes No Transfer end? Set error flag. Yes C User's Manual U14046EJ5V0UD 369 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-21. Master Operation Flowchart (4/5) When transmission is completed, issue the stop condition to notify the slave of completion of transmission. C Issue stop condition. SPT0 = 1 No SPD0 = 1? Yes END For reception, the data transfer direction must be changed. Issue the start condition again and redo (restart) communication. Reception Issue start condition. STT0 = 1 No STD0 = 1? Yes Because the master receives data this time, set the R/W bit to 1 and transmit an address. Transfer slave address. IIC0 address, R/W (1) INTIIC0 = 1? No Yes Clear INTIIC0. ACKD0 = 1? No Yes D 370 End (no acknowledgment) User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-21. Master Operation Flowchart (5/5) D Set so that ACK is automatically returned after an 8-clock wait (set ACKE0 so that ACK is returned except when the last data is received. Specify an 8-clock wait so that automatic returning of ACK can be cleared when the last data is received). Re-set IIC control register 0. ACKE0 = 1, WTIM0 = 0 Write dummy data to IIC0 and start reception (reception can also be started when WREL0 = 1). Start data reception. IIC0 0FFH INTIIC0 = 1? No Reception is completed when INTIIC0 occurs. Yes Clear INTIIC0. Save receive data. Yes Save the received data to a buffer. Remaining data? No Re-set IIC control register 0. ACKE0 = 0, WREL0 = WTIM0 = 1 INTIIC0 = 1? No When reception of data is completed, disable automatic returning of ACK, set a 9clock wait, cancel wait in the ACK cycle, and stop at the 9th clock. As a result, ACK is not returned to the slave. This indicates the completion of reception. Issue the stop condition and end communication. Yes Issue stop condition. SPT0 = 1 SPD0 = 1? No Yes END Remark While the slave is outputting a low level to the data line, the master cannot issue the stop condition. This happens if EEPROM is not reset, even though the microcontroller is reset, because of supply voltage fluctuation during communication (reading from EEPROM). In this case, the EEPROM continues sending data, and may output a low level to the data line. Because the structure of I2C does not allow the master to forcibly make the data line high, the master cannot issue the stop condition. To avoid this phenomenon, it is possible to use a clock line as a port, output a dummy clock from the port, continue reading data from EEPROM by inputting the dummy clock, and complete reading with some EEPROMs (because the data line goes high when reading is completed, the master can issue the stop condition. After that, the status of EEPROM can be controlled). At this time, the port corresponding to the data line must always be in the high-impedance state (high-level output). User's Manual U14046EJ5V0UD 371 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (2) Slave operation The processing procedure of the slave operation is as follows. Basically, the slave operation is event-driven. Therefore, processing by the INTIIC0 interrupt (processing that must substantially change the operation status such as detection of a stop condition during communication) is necessary. In the following explanation, it is assumed that the extension code is not supported for data communication. It is also assumed that the INTIIC0 interrupt servicing only performs status transition processing, and that actual data communication is performed by the main processing. INTIIC0 Flag Interrupt servicing Setting Main processing IIC0 Data Setting Therefore, data communication processing is performed by preparing the following three flags and passing them to the main processing instead of INTIIC0. <1> Communication mode flag This flag indicates the following two communication statuses. * Clear mode: Status in which data communication is not performed * Communication mode: Status in which data communication is performed (from valid address detection to stop condition detection, no detection of ACK from master, address mismatch) <2> Ready flag This flag indicates that data communication is enabled. Its function is the same as the INTIIC0 interrupt for ordinary data communication. This flag is set by interrupt servicing and cleared by the main processing. Clear this flag by interrupt servicing when communication is started. However, the ready flag is not set by interrupt servicing when the first data is transmitted. Therefore, the first data is transmitted without the flag being cleared (an address match is interpreted as a request for the next data). <3> Communication direction flag This flag indicates the direction of communication. Its value is the same as TRC0. 372 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) The main processing of the slave operation is explained next. Start serial interface IIC0 and wait until communication is enabled. When communication is enabled, execute communication by using the communication mode flag and ready flag (processing of the stop condition and start condition is performed by an interrupt. Here, check the status by using the flags). The transmission operation is repeated until the master no longer returns ACK. If ACK is not returned from the master, communication is completed. For reception, the necessary amount of data is received. When communication is completed, ACK is not returned as the next data. After that, the master issues a stop condition or restart condition. Exit from the communication status occurs in this way. Figure 18-22. Slave Operation Flowchart (1/2) START IICC0 xxH IICE0 = 1 No Communication mode? Yes Communication direction flag = 1? No ACKE0 = WTIM0 = 1 Yes WTIM0 = 1 WREL0 = 1 Data processing Communication mode? No Yes IIC0 data No Ready? Yes No Communication mode? Read data. Yes Ready? No Clear ready flag. Yes Data processing Clear ready flag. ACKD0 = 1? No No Communication ends? Yes Yes ACKE0 = 0 WREL0 = 1 WREL0 = 1 Clear communication mode flag. User's Manual U14046EJ5V0UD 373 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) An example of the processing procedure of the slave with the INTIIC0 interrupt is explained below (processing is performed assuming that no extension code is used). The INTIIC0 interrupt checks the status, and the following operations are performed. <1> Communication is stopped if the stop condition is issued. <2> If the start condition is issued, the address is checked and communication is completed if the address does not match. If the address matches, the communication mode is set, wait is cancelled, and processing returns from the interrupt (the ready flag is cleared). <3> For data transmit/receive, only the ready flag is set. Processing returns from the interrupt with the IIC0 bus remaining in the wait status. Remark <1> to <3> above correspond to <1> to <3> in Figure 18-22 Slave Operation Flowchart (2/2). Figure 18-22. Slave Operation Flowchart (2/2) Generate INTIIC0 SPD0 = 1 Yes <1> Yes <2> No STD0 = 1 No COI0 = 1? <3> Yes Communication direction flag TRC0 Set communication mode flag and clear ready flag. Set ready flag Complete interrupt servicing. Complete interrupt servicing. End processing LREL0 = 1 Clear communication mode flag. Complete interrupt servicing. 374 User's Manual U14046EJ5V0UD No CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) 18.5.16 Timing of I2C interrupt request (INTIIC0) occurrence The INTIIC0 interrupt request timing and IIC status register 0 (IICS0) settings corresponding to that timing are described below. (1) Master device operation (a) Start ~ Address ~ Data ~ Data ~ Stop (normal transmission/reception) (i) When WTIM0 = 0 SPT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 5 1: IICS0 = 1000x110B 2: IICS0 = 1000x000B 3: IICS0 = 1000x000B (Sets WTIM0) 4: IICS0 = 1000xx00B (Sets SPT0) 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 SPT0 = 1 AK SP 3 4 1: IICS0 = 1000x110B 2: IICS0 = 1000x100B 3: IICS0 = 1000xx00B (Sets SPT0) 4: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 375 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (b) Start ~ Address ~ Data ~ Start ~ Address ~ Data ~ Stop (restart) (i) When WTIM0 = 0 STT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK 2 ST SPT0 = 1 AD6 to AD0 RW AK 3 D7 to D0 4 AK 5 SP 6 7 1: IICS0 = 1000x110B 2: IICS0 = 1000x000B (Sets WTIM0) 3: IICS0 = 1000xx00B (Clears WTIM0, sets STT0) 4: IICS0 = 1000x110B 5: IICS0 = 1000x000B (Sets WTIM0) 6: IICS0 = 1000xx00B (Sets SPT0) 7: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 STT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK ST SPT0 = 1 AD6 to AD0 RW 2 1: IICS0 = 1000x110B 2: IICS0 = 1000xx00B (Sets STT0) 3: IICS0 = 1000x110B 4: IICS0 = 1000xx00B (Sets SPT0) 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: 376 Don't care User's Manual U14046EJ5V0UD AK D7 to D0 3 AK SP 4 5 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (c) Start ~ Code ~ Data ~ Data ~ Stop (extension code transmission) (i) When WTIM0 = 0 SPT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK 3 SP 4 5 1: IICS0 = 1010x110B 2: IICS0 = 1010x000B 3: IICS0 = 1010x000B (Sets WTIM0) 4: IICS0 = 1010xx00B (Sets SPT0) 5: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 SPT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 1010x110B 2: IICS0 = 1010x100B 3: IICS0 = 1010xx00B (Sets SPT0) 4: IICS0 = 00001001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 377 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (2) Slave device operation (slave address data reception time (matches with SVA0)) (a) Start ~ Address ~ Data ~ Data ~ Stop (i) When WTIM0 = 0 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 0001x110B 2: IICS0 = 0001x000B 3: IICS0 = 0001x000B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 1: IICS0 = 0001x110B 2: IICS0 = 0001x100B 3: IICS0 = 0001xx00B 4: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: 378 Don't care User's Manual U14046EJ5V0UD AK SP 3 4 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (b) Start ~ Address ~ Data ~ Start ~ Address ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, matches with SVA0) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW AK 2 D7 to D0 3 AK SP 4 5 1: IICS0 = 0001x110B 2: IICS0 = 0001x000B 3: IICS0 = 0001x110B 4: IICS0 = 0001x000B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, matches with SVA0) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW 2 AK D7 to D0 3 AK SP 4 5 1: IICS0 = 0001x110B 2: IICS0 = 0001xx00B 3: IICS0 = 0001x110B 4: IICS0 = 0001xx00B 5: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 379 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (c) Start ~ Address ~ Data ~ Start ~ Code ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, extension code reception) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW 2 AK D7 to D0 3 AK SP 4 5 1: IICS0 = 0001x110B 2: IICS0 = 0001x000B 3: IICS0 = 0010x010B 4: IICS0 = 0010x000B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, extension code reception) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW 2 1: IICS0 = 0001x110B 2: IICS0 = 0001xx00B 3: IICS0 = 0010x010B 4: IICS0 = 0010x110B 5: IICS0 = 0010xx00B 6: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: 380 Don't care User's Manual U14046EJ5V0UD AK 3 D7 to D0 4 AK SP 5 6 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (d) Start ~ Address ~ Data ~ Start ~ Address ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, does not match with address (= not extension code)) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW AK 2 D7 to D0 AK SP 3 4 1: IICS0 = 0001x110B 2: IICS0 = 0001x000B 3: IICS0 = 00000x10B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, does not match with address (= not extension code)) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW 2 AK D7 to D0 3 AK SP 4 1: IICS0 = 0001x110B 2: IICS0 = 0001xx00B 3: IICS0 = 00000x10B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 381 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (3) Slave device operation (when receiving extension code) (a) Start ~ Code ~ Data ~ Data ~ Stop (i) When WTIM0 = 0 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 0010x010B 2: IICS0 = 0010x000B 3: IICS0 = 0010x000B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK 1 D7 to D0 2 AK D7 to D0 3 1: IICS0 = 0010x010B 2: IICS0 = 0010x110B 3: IICS0 = 0010x100B 4: IICS0 = 0010xx00B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: 382 Don't care User's Manual U14046EJ5V0UD AK SP 4 5 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (b) Start ~ Code ~ Data ~ Start ~ Address ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, matches with SVA0) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW AK 2 D7 to D0 AK 3 4 D7 to D0 AK SP 5 1: IICS0 = 0010x010B 2: IICS0 = 0010x000B 3: IICS0 = 0001x110B 4: IICS0 = 0001x000B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, matches with SVA0) ST AD6 to AD0 RW AK 1 D7 to D0 2 AK ST AD6 to AD0 3 RW AK 4 SP 5 6 1: IICS0 = 0010x010B 2: IICS0 = 0010x110B 3: IICS0 = 0010xx00B 4: IICS0 = 0001x110B 5: IICS0 = 0001xx00B 6: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 383 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (c) Start ~ Code ~ Data ~ Start ~ Code ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, extension code reception) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW 2 AK D7 to D0 3 AK SP 4 5 1: IICS0 = 0010x010B 2: IICS0 = 0010x000B 3: IICS0 = 0010x010B 4: IICS0 = 0010x000B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, extension code reception) ST AD6 to AD0 RW AK 1 D7 to D0 2 AK ST AD6 to AD0 RW 3 1: IICS0 = 0010x010B 2: IICS0 = 0010x110B 3: IICS0 = 0010xx00B 4: IICS0 = 0010x010B 5: IICS0 = 0010x110B 6: IICS0 = 0010xx00B 7: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: 384 Don't care User's Manual U14046EJ5V0UD AK 4 D7 to D0 5 AK SP 6 7 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (d) Start ~ Code ~ Data ~ Start ~ Address ~ Data ~ Stop (i) When WTIM0 = 0 (after restart, does not match with address (= not extension code)) ST AD6 to AD0 RW AK D7 to D0 1 AK ST AD6 to AD0 RW AK 2 D7 to D0 AK SP 3 4 1: IICS0 = 0010x010B 2: IICS0 = 0010x000B 3: IICS0 = 00000x10B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 (after restart, does not match with address (= not extension code)) ST AD6 to AD0 RW AK 1 D7 to D0 AK 2 ST AD6 to AD0 RW AK 3 D7 to D0 4 AK SP 5 1: IICS0 = 0010x010B 2: IICS0 = 0010x110B 3: IICS0 = 0010xx00B 4: IICS0 = 00000x10B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (4) Operation without communication (a) Start ~ Code ~ Data ~ Data ~ Stop ST AD6 to AD0 RW AK D7 to D0 AK D7 to D0 AK SP 1 1: IICS0 = 00000001B Remark : Generated only when SPIE0 = 1 User's Manual U14046EJ5V0UD 385 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (5) Arbitration loss operation (operation as slave after arbitration loss) (a) When arbitration loss occurs during transmission of slave address data (i) When WTIM0 = 0 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 0101x110B (Example When ALD0 is read during interrupt servicing) 2: IICS0 = 0001x000B 3: IICS0 = 0001x000B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 0101x110B (Example When ALD0 is read during interrupt servicing) 2: IICS0 = 0001x100B 3: IICS0 = 0001xx00B 4: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: 386 Don't care User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (b) When arbitration loss occurs during transmission of extension code (i) When WTIM0 = 0 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 4 1: IICS0 = 0110x010B (Example When ALD0 is read during interrupt servicing) 2: IICS0 = 0010x000B 3: IICS0 = 0010x000B 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK 1 D7 to D0 2 AK D7 to D0 3 AK SP 4 5 1: IICS0 = 0110x010B (Example When ALD0 is read during interrupt servicing) 2: IICS0 = 0010x110B 3: IICS0 = 0010x100B 4: IICS0 = 0010xx00B 5: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 387 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (6) Operation when arbitration loss occurs (no communication after arbitration loss) (a) When arbitration loss occurs during transmission of slave address data (when WTIM0 = 1) ST AD6 to AD0 RW AK D7 to D0 AK D7 to D0 AK SP 1 2 1: IICS0 = 01000110B (Example When ALD0 is read during interrupt servicing) 2: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 (b) When arbitration loss occurs during transmission of extension code ST AD6 to AD0 RW AK D7 to D0 AK D7 to D0 1 AK SP 2 1: IICS0 = 0110x010B (Example When ALD0 is read during interrupt servicing) LREL0 is set to "1" by software 2: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 x: 388 Don't care User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (c) When arbitration loss occurs during transmission of data (i) When WTIM0 = 0 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 AK SP 2 3 1: IICS0 = 10001110B 2: IICS0 = 01000000B (Example When ALD0 is read during interrupt servicing) 3: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 (ii) When WTIM0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK SP 3 1: IICS0 = 10001110B 2: IICS0 = 01000100B (Example When ALD0 is read during interrupt servicing) 3: IICS0 = 00000001B Remark : Always generated : Generated only when SPIE0 = 1 User's Manual U14046EJ5V0UD 389 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (d) When loss occurs due to restart condition during data transfer (i) Not extension code (Example: unmatches with SVA0, WTIM0 = 1) ST AD6 to AD0 RW AK D7 to Dn ST AD6 to AD0 RW AK 1 D7 to D0 AK SP 2 3 1: IICS0 = 1000x110B 2: IICS0 = 01000110B (Example When ALD0 is read during interrupt servicing) 3: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care n = 6 to 0 (ii) Extension code ST AD6 to AD0 RW AK D7 to Dn ST AD6 to AD0 RW 1 AK D7 to D0 AK 2 1: IICS0 = 1000x110B 2: IICS0 = 0110x010B (Example When ALD0 is read during interrupt servicing) Sets LREL0 = 1 by software 3: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care n = 6 to 0 390 User's Manual U14046EJ5V0UD SP 3 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (e) When loss occurs due to stop condition during data transfer ST AD6 to AD0 RW AK D7 to Dn SP 1 2 1: IICS0 = 1000x110B 2: IICS0 = 01000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care n = 6 to 0 (f) When arbitration loss occurs due to low-level data when attempting to generate a restart condition (i) When WTIM0 = 1 STT0 = 1 ST AD6 to AD0 RW AK D7 to D0 AK 1 D7 to D0 2 AK D7 to D0 AK SP 3 4 1: IICS0 = 1000x110B 2: IICS0 = 1000x100B (Sets STT0) 3: IICS0 = 01000100B (Example When ALD0 is read during interrupt servicing) 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care (g) When arbitration loss occurs due to a stop condition when attempting to generate a restart condition (i) When WTIM0 = 1 STT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK SP 2 3 1: IICS0 = 1000x110B 2: IICS0 = 1000xx00B (Sets STT0) 3: IICS0 = 01000001B : Always generated Remark : Generated only when SPIE0 = 1 x: Don't care User's Manual U14046EJ5V0UD 391 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) (h) When arbitration loss occurs due to low-level data when attempting to generate a stop condition (i) When WTIM0 = 1 SPT0 = 1 ST AD6 to AD0 RW AK D7 to D0 1 AK D7 to D0 2 AK D7 to D0 AK SP 3 1: IICS0 = 1000x110B 2: IICS0 = 1000xx00B (Sets SPT0) 3: IICS0 = 01000000B (Example When ALD0 is read during interrupt servicing) 4: IICS0 = 00000001B : Always generated Remark : Generated only when SPIE0 = 1 x: 392 Don't care User's Manual U14046EJ5V0UD 4 CHAPTER 18 18.6 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Timing Charts When using the I2C bus mode, the master device outputs an address via the serial bus to select one of several slave devices as its communication partner. After outputting the slave address, the master device transmits the TRC0 bit (bit 3 of IIC status register 0 (IICS0)), which specifies the data transfer direction, and then starts serial communication with the slave device. Figures 18-23 and 18-24 show timing charts of the data communication. IIC shift register 0 (IIC0)'s shift operation is synchronized with the falling edge of the serial clock (SCL0). The transmit data is transferred to the SO0 latch and is output (MSB first) via the SDA0 pin. Data input via the SDA0 pin is captured into IIC0 at the rising edge of SCL0. User's Manual U14046EJ5V0UD 393 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-23. Example of Master to Slave Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (1/3) (1) Start condition ~ address Processing by master device IIC0 address IIC0 IIC0 data ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 STT0 L SPT0 WREL0 L INTIIC0 TRC0 H Transmit Transfer lines SCL0 1 2 A6 A5 Start condition SDA0 3 4 5 6 7 8 9 1 2 3 4 A4 A3 A2 A1 A0 W ACK D7 D6 D5 D4 Processing by slave device IIC0 FFHNote IIC0 ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L Note WREL0 INTIIC0 TRC0 L Receive (When EXC0 = 1) Note To cancel slave wait, write "FFH" to IIC0 or set WREL0. 394 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-23. Example of Master to Slave Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (2/3) (2) Data Processing by master device IIC0 data IIC0 IIC0 data ACKD0 STD0 L SPD0 L WTIM0 H ACKE0 H MSTS0 H STT0 L SPT0 L WREL0 L INTIIC0 TRC0 H Transmit Transfer lines SCL0 8 9 SDA0 D0 1 2 3 4 5 6 7 8 D7 D6 D5 D4 D3 D2 D1 D0 9 1 2 3 D7 D6 D5 Processing by slave device IIC0 IIC0 FFHNote IIC0 FFHNote Note Note ACKD0 STD0 L SPD0 L WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L WREL0 INTIIC0 TRC0 L Receive Note To cancel slave wait, write "FFH" to IIC0 or set WREL0. User's Manual U14046EJ5V0UD 395 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-23. Example of Master to Slave Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (3/3) (3) Stop condition Processing by master device IIC0 data IIC0 IIC0 address ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 STT0 SPT0 WREL0 L INTIIC0 (When SPIE0 = 1) TRC0 H Transmit Transfer lines SCL0 1 2 3 4 5 6 7 8 SDA0 D7 D6 D5 D4 D3 D2 D1 D0 9 Stop condition Processing by slave device IIC0 FFHNote IIC0 Start condition IIC0 FFHNote ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L Note WREL0 Note INTIIC0 (When SPIE0 = 1) TRC0 L Receive Note To cancel slave wait, write "FFH" to IIC0 or set WREL0. 396 User's Manual U14046EJ5V0UD 1 2 A6 A5 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-24. Example of Slave to Master Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (1/3) (1) Start condition ~ address Processing by master device IIC0 address IIC0 IIC0 FFHNote ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 STT0 SPT0 L Note WREL0 INTIIC0 TRC0 Transfer lines SCL0 1 2 SDA0 A6 A5 Start condition 3 4 5 6 7 8 A4 A3 A2 A1 A0 R 9 1 2 3 4 5 6 D7 D6 D5 D4 D3 D2 Processing by slave device IIC0 data IIC0 ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L WREL0 L INTIIC0 TRC0 Note To cancel master wait, write "FFH" to IIC0 or set WREL0. User's Manual U14046EJ5V0UD 397 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-24. Example of Slave to Master Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (2/3) (2) Data Processing by master device IIC0 FFHNote IIC0 FFHNote IIC0 ACKD0 STD0 L SPD0 L WTIM0 H ACKE0 H MSTS0 H STT0 L SPT0 L Note WREL0 Note INTIIC0 TRC0 L Receive Transfer lines SCL0 8 9 1 2 3 4 5 6 7 8 9 SDA0 D0 ACK D7 D6 D5 D4 D3 D2 D1 D0 ACK 1 D7 2 3 D6 D5 Processing by slave device IIC0 data IIC0 IIC0 data ACKD0 STD0 L SPD0 L WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L WREL0 L INTIIC0 TRC0 H Transmit Note To cancel master wait, write "FFH" to IIC0 or set WREL0. 398 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) Figure 18-24. Example of Slave to Master Communication (When 9-Clock Wait Is Selected for Both Master and Slave) (3/3) (3) Stop condition Processing by master device IIC0 FFHNote IIC0 IIC0 address ACKD0 STD0 SPD0 WTIM0 H ACKE0 MSTS0 STT0 SPT0 Note WREL0 INTIIC0 (When SPIE0 = 1) TRC0 Transfer lines SCL0 1 2 3 4 5 6 7 8 SDA0 D7 D6 D5 D4 D3 D2 D1 D0 9 1 N-ACK Stop condition A6 Start condition 2 A5 Processing by slave device IIC0 data IIC0 ACKD0 STD0 SPD0 WTIM0 H ACKE0 H MSTS0 L STT0 L SPT0 L WREL0 INTIIC0 (When SPIE0 = 1) TRC0 Note To cancel master wait, write "FFH" to IIC0 or set WREL0. User's Manual U14046EJ5V0UD 399 CHAPTER 19 INTERRUPT FUNCTIONS 19.1 Interrupt Function Types The following three types of interrupt functions are used. (1) Non-maskable interrupt This interrupt is acknowledged even in an interrupt disabled state. It does not undergo priority control and is given top priority over all other interrupt requests. The other interrupt requests are held pending while the nonmaskable interrupt is serviced. The non-maskable interrupt generates a standby release signal and releases the HALT mode during main system clock operation. The non-maskable interrupt has only interrupt request from the watchdog timer. (2) Maskable interrupts These interrupts undergo mask control. Maskable interrupts can be divided into a high interrupt priority group and a low interrupt priority group by setting the priority specification flag registers (PR0L, PR0H, PR1L). Multiple high priority interrupts can be applied to low priority interrupts. If two or more interrupts with the same priority are simultaneously generated, each interrupt has a predetermined priority (see Table 19-1). The maskable interrupt generates a standby release signal and releases the STOP and HALT modes. Five external interrupt requests and 13 internal interrupt requests are incorporated as maskable interrupts. (3) Software interrupt This is a vectored interrupt to be generated by executing the BRK instruction. It is acknowledged even in an interrupt disabled state. The software interrupt does not undergo interrupt priority control. 19.2 Interrupt Sources and Configuration A total of 20 interrupt sources exist among non-maskable, maskable, and software interrupts (see Table 19-1). Remark A non-maskable interrupt or a maskable interrupt (internal) can be selected as the watchdog timer interrupt (INTWDT). 400 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS Table 19-1. Interrupt Source List Interrupt Type Default PriorityNote 1 Interrupt Source Name Internal/ External Vector Table Address Internal 0004H Trigger Nonmaskable - INTWDT Watchdog timer overflow (with watchdog timer mode 1 selected) Maskable 0 INTWDT Watchdog timer overflow (with interval timer mode selected) 1 INTP0 Pin input edge detection 2 INTP1 0008H 3 INTP2 000AH 4 INTP3 000CH 5 INTSER0 Serial interface UART0 reception error generation 6 INTSR0 End of serial interface UART0 reception 0010H 7 INTST0 End of serial interface UART0 transmission 0012H 8 INTCSI30 End of serial interface SIO30 transfer 0014H 9 INTCSI31 End of serial interface SIO31 transfer [only for PD780024A, 780034A Subseries] 0016H 10 INTIIC0 End of serial interface IIC0 transfer [only for PD780024AY, 780034AY Subseries] 0018H 11 INTWTI Reference time interval signal from watch timer 001AH 12 INTTM00 Match between TM0 and CR00 (when CR00 is specified as compare register) Detection of TI00 or TI01 valid edge 001CH Basic Configuration TypeNote 2 (A) (B) External Internal 0006H 000EH (C) (B) (when CR00 is specified as capture register) Software 13 INTTM01 Match between TM0 and CR01 (when CR01 is specified as compare register) Detection of TI00 valid edge (when CR01 is specified as capture register) 001EH 14 INTTM50 Match between TM50 and CR50 0020H 15 INTTM51 Match between TM51 and CR51 0022H 16 INTAD0 End of A/D converter conversion 0024H 17 INTWT Watch timer overflow 0026H 18 INTKR Port 4 falling edge detection - BRK BRK instruction execution External 0028H (D) - 003EH (E) Notes 1. The default priority is the priority applicable when two or more maskable interrupts are generated simultaneously. 0 is the highest priority, and 18 is the lowest. 2. Basic configuration types (A) to (E) correspond to (A) to (E) in Figure 19-1. User's Manual U14046EJ5V0UD 401 CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-1. Basic Configuration of Interrupt Function (1/2) (A) Internal non-maskable interrupt Internal bus Interrupt request Vector table address generator Priority controller Standby release signal (B) Internal maskable interrupt Internal bus MK Interrupt request IE PR ISP Priority controller IF Vector table address generator Standby release signal (C) External maskable interrupt (INTP0 to INTP3) Internal bus External interrupt edge enable register (EGP, EGN) Interrupt request Edge detector MK IF IE PR ISP Priority controller Vector table address generator Standby release signal 402 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-1. Basic Configuration of Interrupt Function (2/2) (D) External maskable interrupt (INTKR) Internal bus MK Interrupt request Falling edge detector IE PR ISP Priority controller IF Vector table address generator 1 when MEM = 01H Standby release signal (E) Software interrupt Internal bus Interrupt request IF: Vector table address generator Interrupt request flag IE: Interrupt enable flag ISP: In-service priority flag MK: Interrupt mask flag PR: Priority specification flag MEM: Memory expansion mode register User's Manual U14046EJ5V0UD 403 CHAPTER 19 INTERRUPT FUNCTIONS 19.3 Interrupt Function Control Registers The following 6 types of registers are used to control the interrupt functions. * Interrupt request flag registers (IF0L, IF0H, IF1L) * Interrupt mask flag registers (MK0L, MK0H, MK1L) * Priority specification flag registers (PR0L, PR0H, PR1L) * External interrupt rising edge enable register (EGP) * External interrupt falling edge enable register (EGN) * Program status word (PSW) Table 19-2 gives a list of interrupt request flags, interrupt mask flags, and priority specification flags corresponding to interrupt request sources. Table 19-2. Flags Corresponding to Interrupt Request Sources Interrupt Source Interrupt Request Flag Interrupt Mask Flag Register WDTIFNote 1 INTWDT INTP0 INTP1 INTP2 INTP3 INTSER0 INTSR0 INTST0 PIF0 PIF1 PIF2 PIF3 SERIF0 SRIF0 STIF0 INTCSI30 INTCSI31Note 2 INTIIC0Note 3 INTWTI INTTM00 INTTM01 INTTM50 INTTM51 INTAD0 INTWT INTKR Register Register IF0L WDTMK PMK0 PMK1 PMK2 PMK3 SERMK0 SRMK0 STMK0 MK0L WDTPR PPR0 PPR1 PPR2 PPR3 SERPR0 SRPR0 STPR0 PR0L CSIIF30 CSIIF31Note 2 IICIF0Note 3 WTIIF TMIF00 TMIF01 TMIF50 TMIF51 IF0H CSIMK30 CSIMK31Note 2 IICMK0Note 3 WTIMK TMMK00 TMMK01 TMMK50 TMMK51 MK0H CSIPR30 CSIPR31Note 2 IICPR0Note 3 WTIPR TMPR00 TMPR01 TMPR50 TMPR51 PR0H ADIF0 WTIF KRIF IF1L ADMK0 WTMK KRMK MK1L ADPR0 WTPR KRPR PR1L Notes 1. Interrupt control flag when watchdog timer is used as interval timer 2. PD780024A, 780034A Subseries only 3. PD780024AY, 780034AY Subseries only 404 Priority Specification Flag User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS (1) Interrupt request flag registers (IF0L, IF0H, IF1L) The interrupt request flags are set to 1 when the corresponding interrupt request is generated or an instruction is executed. They are cleared to 0 when an instruction is executed upon acknowledgment of an interrupt request or upon application of RESET input. IF0L, IF0H, and IF1L are set by a 1-bit or 8-bit memory manipulation instruction. When IF0L and IF0H are combined to form 16-bit register IF0, they are set by a 16-bit memory manipulation instruction. RESET input clears these registers to 00H. Figure 19-2. Format of Interrupt Request Flag Registers (IF0L, IF0H, IF1L) Address: FFE0H After reset: 00H R/W Symbol IF0L <7> <6> <5> <4> <3> <2> <1> <0> STIF0 SRIF0 SERIF0 PIF3 PIF2 PIF1 PIF0 WDTIF <4> <3> <2> <1> <0> TMIF00 WTIIF IICIF0Note 1 CSIIF31Note 2 CSIIF30 Address: FFE1H After reset: 00H R/W Symbol IF0H <7> TMIF51 <6> TMIF50 <5> TMIF01 Address: FFE2H After reset: 00H R/W Symbol 7 6 5 4 3 <2> <1> <0> IF1L 0 0 0 0 0 KRIF WTIF ADIF0 XXIFX Interrupt request flag 0 No interrupt request signal is generated 1 Interrupt request signal is generated, interrupt request status Notes 1. Incorporated only in the PD780024AY, 780034AY Subseries. Be sure to clear 0 for the PD780024A, 780034A Subseries. 2. Incorporated only in the PD780024A, 780034A Subseries. Be sure to clear 0 for the PD780024AY, 780034AY Subseries. Cautions 1. The WDTIF flag is R/W enabled only when the watchdog timer is used as the interval timer. If watchdog timer mode 1 is used, set the WDTIF flag to 0. 2. Be sure to clear bits 3 to 7 of IF1L to 0. 3. When operating a timer, serial interface, or A/D converter after standby release, run it once after clearing an interrupt request flag. An interrupt request flag may be set by noise. 4. When an interrupt is acknowledged, the interrupt request flag is automatically cleared, and then processing of the interrupt routine is started. 5. Use the 1-bit memory manipulation instruction (CLR1) for manipulating the flag of the interrupt request flag register. Use the bit manipulation instruction such as "IF0L.0 = 0;" or "_asm("clr1 IF0L, 0");" for describing in C language because the compiled assembler needs to be the 1-bit memory manipulation instruction (CLR1). If a program is described in C language using an 8-bit memory manipulation instruction such as "IF0L & = 0xfe;" and compiled, the assembler of the following three instructions is described. mov a, IF0L and a, #0FEH mov IF0L, a In this case, at the timing between "mov a, IF0L" and "mov IF0L, a", if the request flag of another bit of the identical interrupt request flag register is set to 1, it is cleared to 0 by "mov IF0L, a". Therefore, care must be exercised when using an 8-bit memory manipulation instruction in C language. User's Manual U14046EJ5V0UD 405 CHAPTER 19 INTERRUPT FUNCTIONS (2) Interrupt mask flag registers (MK0L, MK0H, MK1L) The interrupt mask flags are used to enable/disable the corresponding maskable interrupt service. MK0L, MK0H, and MK1L are set by a 1-bit or 8-bit memory manipulation instruction. When MK0L and MK0H are combined to form a 16-bit register MK0, they are set by a 16-bit memory manipulation instruction. RESET input sets these registers to FFH. Figure 19-3. Format of Interrupt Mask Flag Registers (MK0L, MK0H, MK1L) Address: FFE4H After reset: FFH R/W Symbol MK0L <7> <6> <5> <4> <3> <2> <1> <0> STMK0 SRMK0 SERMK0 PMK3 PMK2 PMK1 PMK0 WDTMK <4> <3> <2> <1> <0> TMMK00 WTIMK IICMK0Note 1 CSIMK31Note 2 CSIMK30 Address: FFE5H After reset: FFH R/W Symbol MK0H <7> TMMK51 <6> TMMK50 <5> TMMK01 Address: FFE6H After reset: FFH R/W Symbol 7 6 5 4 3 <2> <1> <0> MK1L 1 1 1 1 1 KRMK WTMK ADMK0 XXMKX Interrupt servicing control 0 Interrupt servicing enabled 1 Interrupt servicing disabled Notes 1. Incorporated only in the PD780024AY, 780034AY Subseries. Be sure to set 1 for the PD780024A, 780034A Subseries. 2. Incorporated only in the PD780024A, 780034A Subseries. Be sure to set 1 for the PD780024AY, 780034AY Subseries. Cautions 1. If the watchdog timer is used in watchdog timer mode 1, the contents of the WDTMK flag become undefined when read. 2. Because port 0 pins have an alternate function as external interrupt request input, when the output level is changed by specifying the output mode of the port function, an interrupt request flag is set. Therefore, 1 should be set in the interrupt mask flag before using the output mode. 3. Be sure to set bits 3 to 7 of MK1L to 1. 406 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS (3) Priority specification flag registers (PR0L, PR0H, PR1L) The priority specification flags are used to set the corresponding maskable interrupt priority orders. PR0L, PR0H, and PR1L are set by a 1-bit or 8-bit memory manipulation instruction. If PR0L and PR0H are combined to form 16-bit register PR0, they are set by a 16-bit memory manipulation instruction. RESET input sets these registers to FFH. Figure 19-4. Format of Priority Specification Flag Registers (PR0L, PR0H, PR1L) Address: FFE8H After reset: FFH R/W Symbol PR0L <7> <6> <5> <4> <3> <2> <1> <0> STPR0 SRPR0 SERPR0 PPR3 PPR2 PPR1 PPR0 WDTPR <4> <3> <2> <1> <0> TMPR00 WTIPR IICPR0Note 1 CSIPR31Note 2 CSIPR30 Address: FFE9H After reset: FFH R/W Symbol PR0H <7> TMPR51 <6> TMPR50 <5> TMPR01 Address: FFEAH After reset: FFH R/W Symbol 7 6 5 4 3 <2> <1> <0> PR1L 1 1 1 1 1 KRPR WTPR ADPR0 XXPRX Priority level selection 0 High priority level 1 Low priority level Notes 1. Incorporated only in the PD780024AY, 780034AY Subseries. Be sure to set 1 for the PD780024A, 780034A Subseries. 2. Incorporated only in the PD780024A, 780034A Subseries. Be sure to set 1 for the PD780024AY, 780034AY Subseries. Cautions 1. If the watchdog timer is used in watchdog timer mode 1, set the WDTPR flag to 1. 2. Be sure to set bits 3 to 7 of PR1L to 1. User's Manual U14046EJ5V0UD 407 CHAPTER 19 INTERRUPT FUNCTIONS (4) External interrupt rising edge enable register (EGP), external interrupt falling edge enable register (EGN) These registers specify the valid edge for INTP0 to INTP3. EGP and EGN are set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears these registers to 00H. Figure 19-5. Format of External Interrupt Rising Edge Enable Register (EGP), External Interrupt Falling Edge Enable Register (EGN) Address: FF48H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 EGP 0 0 0 0 EGP3 EGP2 EGP1 EGP0 Address: FF49H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 EGN 0 0 0 0 EGN3 EGN2 EGN1 EGN0 EGPn EGNn 0 0 Interrupt disable 0 1 Falling edge 1 0 Rising edge 1 1 Both rising and falling edges INTPn pin valid edge selection (n = 0 to 3) Caution When the function is switched from external interrupt request to port, edge detection may be performed. Therefore, clear EGPn and EGNn to 0 before switching to the port mode. 408 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS (5) Program status word (PSW) The program status word is a register to hold the instruction execution result and the current status for an interrupt request. The IE flag to set maskable interrupt enable/disable and the ISP flag to control nesting processing are mapped. Besides 8-bit read/write, this register can carry out operations with a bit manipulation instruction and dedicated instructions (EI and DI). When a vectored interrupt request is acknowledged, if the BRK instruction is executed, the contents of PSW are automatically saved into a stack and the IE flag is reset to 0. If a maskable interrupt request is acknowledged, the contents of the priority specification flag of the acknowledged interrupt are transferred to the ISP flag. The PSW contents are also saved into the stack with the PUSH PSW instruction. They are restored from the stack with the RETI, RETB, and POP PSW instructions. RESET input sets PSW to 02H. Figure 19-6. Program Status Word Format PSW 7 6 5 4 3 2 1 0 After reset IE Z RBS1 AC RBS0 0 ISP CY 02H Used when normal instruction is executed ISP Priority of interrupt currently being serviced 0 High-priority interrupt servicing (Low-priority interrupt disable) 1 Interrupt request not acknowledged, or lowpriority interrupt servicing (All maskable interrupts enable) IE Interrupt request acknowledge enable/disable 0 Disable 1 Enable User's Manual U14046EJ5V0UD 409 CHAPTER 19 INTERRUPT FUNCTIONS 19.4 Interrupt Servicing Operations 19.4.1 Non-maskable interrupt request acknowledgment operation A non-maskable interrupt request is unconditionally acknowledged even in an interrupt acknowledgment disabled state. It does not undergo interrupt priority control and has the highest priority of all interrupts. If a non-maskable interrupt request is acknowledged, the contents are saved into the stacks in the order of PSW, then PC, the IE flag and ISP flag are reset (0), and the contents of the vector table are loaded into the PC and branched. Due to this, acknowledgment of multiple interrupts is prohibited. A new non-maskable interrupt request generated during execution of a non-maskable interrupt servicing program is acknowledged after the current non-maskable interrupt servicing program is terminated (following RETI instruction execution) and one main routine instruction has been executed. However, if a new non-maskable interrupt request is generated twice or more during non-maskable interrupt servicing program execution, only one non-maskable interrupt request is acknowledged after termination of the non-maskable interrupt servicing program. Figures 19-7, 19-8, and 19-9 show the flowchart of non-maskable interrupt request generation through acknowledgment, the acknowledgment timing of a non-maskable interrupt request, and the acknowledgment operation when multiple nonmaskable interrupt requests are generated, respectively. Caution 410 Be sure to use the RETI instruction to return from a non-maskable interrupt. User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-7. Non-Maskable Interrupt Request Generation to Acknowledge Flowchart Start WDTM4 = 1 (with watchdog timer mode selected)? No Interval timer Yes Overflow in WDT? No Yes WDTM3 = 0 (with non-maskable interrupt selected)? No Reset processing Yes Interrupt request generation WDT interrupt servicing? No Interrupt request held pending Yes Interrupt control register not accessed? No Yes Start of interrupt servicing WDTM: Watchdog timer mode register WDT: Watchdog timer Figure 19-8. Non-Maskable Interrupt Request Acknowledge Timing CPU processing Instruction Instruction PSW and PC save, jump Interrupt service to interrupt servicing program WDTIF Interrupt request generated during this interval is acknowledged at . WDTIF: Watchdog timer interrupt request flag User's Manual U14046EJ5V0UD 411 CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-9. Non-Maskable Interrupt Request Acknowledge Operation (a) If a non-maskable interrupt request is generated during non-maskable interrupt servicing program execution Main routine NMI request <1> NMI request <2> Execution of NMI request <1> NMI request <2> held pending Execution of 1 instruction Servicing of NMI request <2> that was pended (b) If two non-maskable interrupt requests are generated during non-maskable interrupt servicing program execution Main routine NMI request <1> NMI request <2> Execution of 1 instruction NMI request <3> Execution of NMI request <1> NMI request <2> held pending NMI request <3> held pending Servicing of NMI request <2> that was pended NMI request <3> not acknowledged (Although two or more NMI requests have been generated, only one request is acknowledged.) 412 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS 19.4.2 Maskable interrupt request acknowledgment operation A maskable interrupt request becomes acknowledgeable when an interrupt request flag is set to 1 and the mask (MK) flag corresponding to that interrupt request is cleared to 0. A vectored interrupt request is acknowledged if interrupts are enabled (when the IE flag is set to 1). However, a low-priority interrupt request is not acknowledged during servicing of a higher priority interrupt request (when the ISP flag is reset to 0). Moreover, even if the EI instruction is executed during execution of a non-maskable interrupt servicing program, neither non-maskable interrupt requests nor maskable interrupt requests are acknowledged. The times from generation of a maskable interrupt request until interrupt servicing is performed are listed in Table 19-3 below. For the interrupt request acknowledgment timing, see Figures 19-11 and 19-12. Table 19-3. Times from Generation of Maskable Interrupt Until Servicing Minimum Time Maximum TimeNote When xxPR = 0 7 clocks 32 clocks When xxPR = 1 8 clocks 33 clocks Note If an interrupt request is generated just before a divide instruction, the wait time becomes longer. Remark 1 clock: 1/fCPU (fCPU: CPU clock) If two or more interrupt requests are generated simultaneously, the request with a higher priority level specified by the priority specification flag is acknowledged first. If two or more interrupt requests have the same priority level, the request with the highest default priority is acknowledged first. An interrupt request that is held pending is acknowledged when it becomes acknowledgeable. Figure 19-10 shows the interrupt request acknowledgment algorithm. If a maskable interrupt request is acknowledged, the contents are saved into the stacks in the order of PSW, then PC, the IE flag is reset (0), and the contents of the priority specification flag corresponding to the acknowledged interrupt are transferred to the ISP flag. Further, the vector table data determined for each interrupt request is loaded into the PC and branched. Return from an interrupt is possible using the RETI instruction. User's Manual U14046EJ5V0UD 413 CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-10. Interrupt Request Acknowledge Processing Algorithm Start No xxIF = 1? Yes (Interrupt request generation) No xxMK = 0? Yes Interrupt request held pending Yes (High priority) xxPR = 0? No (Low priority) Yes Any high-priority interrupt request among those simultaneously generated with xxPR = 0? Interrupt request held pending Any high-priority interrupt request among those simultaneously generated with xxPR = 0? No No IE = 1? Yes Interrupt request held pending No Interrupt request held pending Any high-priority interrupt request among those simultaneously generated? No IE = 1? Vectored interrupt servicing Yes ISP = 1? Yes Yes Yes Interrupt request held pending No Interrupt request held pending No Interrupt request held pending Vectored interrupt servicing xxIF: Interrupt request flag xxMK: Interrupt mask flag xxPR: Priority specification flag IE: Flag that controls acknowledge of maskable interrupt request (1 = enable, 0 = disable) ISP: Flag that indicates the priority level of the interrupt currently being serviced (0 = high-priority interrupt servicing, 1 = no interrupt request acknowledged, or low-priority interrupt servicing) 414 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-11. Interrupt Request Acknowledge Timing (Minimum Time) 6 clocks CPU processing Instruction Instruction PSW and PC save, jump to interrupt servicing Interrupt servicing program xxIF (xxPR = 1) 8 clocks xxIF (xxPR = 0) 7 clocks Remark 1 clock: 1/fCPU (fCPU: CPU clock) Figure 19-12. Interrupt Request Acknowledge Timing (Maximum Time) CPU processing Instruction 25 clocks 6 clocks Divide instruction PSW and PC save, jump to interrupt servicing Interrupt servicing program xxIF (xxPR = 1) 33 clocks xxIF (xxPR = 0) 32 clocks Remark 1 clock: 1/fCPU (fCPU: CPU clock) 19.4.3 Software interrupt request acknowledgment operation A software interrupt request is acknowledged by BRK instruction execution. Software interrupts cannot be disabled. If a software interrupt request is acknowledged, the contents are saved into the stacks in the order of the program status word (PSW), then program counter (PC), the IE flag is reset (0), and the contents of the vector table (003EH, 003FH) are loaded into PC and branched. Return from a software interrupt is possible with the RETB instruction. Caution Do not use the RETI instruction for returning from the software interrupt. User's Manual U14046EJ5V0UD 415 CHAPTER 19 INTERRUPT FUNCTIONS 19.4.4 Nesting interrupt servicing Nesting occurs when another interrupt request is acknowledged during execution of an interrupt. Nesting does not occur unless the interrupt request acknowledge enable state is selected (IE = 1) (except nonmaskable interrupts). Also, when an interrupt request is acknowledged, interrupt request acknowledge becomes disabled (IE = 0). Therefore, to enable nesting, it is necessary to set (1) the IE flag with the EI instruction during interrupt servicing to enable interrupt acknowledge. Moreover, even if interrupts are enabled, nesting may not be enabled, this being subject to interrupt priority control. Two types of priority control are available: default priority control and programmable priority control. Programmable priority control is used for nesting. In the interrupt enable state, if an interrupt request with a priority equal to or higher than that of the interrupt currently being serviced is generated, it is acknowledged for nesting. If an interrupt with a priority lower than that of the interrupt currently being serviced is generated during interrupt servicing, it is not acknowledged for nesting. Interrupt requests that are not enabled because of the interrupt disable state or they have a lower priority are held pending. When servicing of the current interrupt ends, the pended interrupt request is acknowledged following execution of at least one main processing instruction execution. Nesting is not possible during non-maskable interrupt servicing. Table 19-4 shows interrupt requests enabled for nesting and Figure 19-13 shows nesting examples. Table 19-4. Interrupt Requests Enabled for Nesting During Interrupt Servicing Nesting Request Non-Maskable Maskable Interrupt Request Interrupt Request PR = 0 Software Interrupt PR = 1 Request Interrupt Being Serviced IE = 1 IE = 0 IE = 1 IE = 0 x x x x ISP = 0 x x x ISP = 1 x x x x x Non-maskable interrupt Maskable interrupt Software interrupt Remarks 1. : Nesting enabled 2. x: Nesting disabled 3. ISP and IE are flags contained in the PSW. ISP = 0: An interrupt with higher priority is being serviced. ISP = 1: No interrupt request has been acknowledged, or an interrupt with a lower priority is being serviced. IE = 0: Interrupt request acknowledgment is disabled. IE = 1: Interrupt request acknowledgment is enabled. 4. PR is a flag contained in PR0L, PR0H, and PR1L. PR = 0: Higher priority level PR = 1: Lower priority level 416 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-13. Nesting Examples (1/2) Example 1. Nesting occurs twice Main processing INTxx servicing IE = 0 EI INTyy servicing IE = 0 IE = 0 EI INTxx (PR = 1) INTzz servicing EI INTyy (PR = 0) INTzz (PR = 0) RETI IE = 1 RETI IE = 1 RETI IE = 1 During servicing of interrupt INTxx, two interrupt requests, INTyy and INTzz, are acknowledged, and nesting takes place. Before each interrupt request is acknowledged, the EI instruction must always be issued to enable interrupt request acknowledgment. Example 2. Nesting does not occur due to priority control Main processing INTxx servicing INTyy servicing IE = 0 EI EI INTxx (PR = 0) INTyy (PR = 1) RETI IE = 1 1 instruction execution IE = 0 RETI IE = 1 Interrupt request INTyy issued during servicing of interrupt INTxx is not acknowledged because its priority is lower than that of INTxx, and nesting does not take place. The INTyy interrupt request is held pending, and is acknowledged following execution of one main processing instruction. PR = 0: Higher priority level PR = 1: Lower priority level IE = 0: Interrupt request acknowledgment disabled User's Manual U14046EJ5V0UD 417 CHAPTER 19 INTERRUPT FUNCTIONS Figure 19-13. Nesting Examples (2/2) Example 3. Nesting does not occur because interrupts are not enabled Main processing INTxx servicing INTyy servicing IE = 0 EI INTyy (PR = 0) INTxx (PR = 0) RETI IE = 1 1 instruction execution IE = 0 RETI IE = 1 Interrupts are not enabled during servicing of interrupt INTxx (EI instruction is not issued), so interrupt request INTyy is not acknowledged and nesting does not take place. The INTyy interrupt request is held pending, and is acknowledged following execution of one main processing instruction. PR = 0: Higher priority level IE = 0: Interrupt request acknowledgment disabled 418 User's Manual U14046EJ5V0UD CHAPTER 19 INTERRUPT FUNCTIONS 19.4.5 Interrupt request hold There are instructions where, even if an interrupt request is issued for them while another instruction is executed, request acknowledge is held pending until the end of execution of the next instruction. These instructions (interrupt request hold instructions) are listed below. * MOV PSW, #byte * MOV A, PSW * MOV PSW, A * MOV1 PSW.bit, CY * MOV1 CY, PSW.bit * AND1 CY, PSW.bit * OR1 CY, PSW.bit * XOR1 CY, PSW.bit * SET1 PSW.bit * CLR1 PSW.bit * RETB * RETI * PUSH PSW * POP PSW * BT PSW.bit, $addr16 * BF PSW.bit, $addr16 * BTCLR PSW.bit, $addr16 * EI * DI * Manipulate instructions for the IF0L, IF0H, IF1L, MK0L, MK0H, MK1L, PR0L, PR0H, and PR1L registers Caution The BRK instruction is not one of the above-listed interrupt request hold instructions. However, the software interrupt activated by executing the BRK instruction causes the IE flag to be cleared to 0. Therefore, even if a maskable interrupt request is generated during execution of the BRK instruction, the interrupt request is not acknowledged. However, a non-maskable interrupt request is acknowledged. Figure 19-14 shows the timing with which interrupt requests are held pending. Figure 19-14. Interrupt Request Hold CPU processing Instruction N Instruction M Save PSW and PC, Jump to interrupt servicing Interrupt servicing program xxIF Remarks 1. Instruction N: Interrupt request hold instruction 2. Instruction M: Instruction other than interrupt request hold instruction 3. The xxPR (priority level) values do not affect the operation of xxIF (interrupt request). User's Manual U14046EJ5V0UD 419 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Use the expanded-specification products of the PD780024A and 780034A Subseries, under the conventionalspecification conditions (fX = 8.38 MHz: VDD = 4.0 to 5.5 V, fX = 5 MHz: VDD = 2.7 to 5.5 V, fX = 1.25 MHz: VDD = 1.8 to 5.5 V). The external device expansion function cannot be used under the expanded-specification conditions (high-speed operation). 20.1 External Device Expansion Function The external device expansion function connects external devices to areas other than the internal ROM, RAM, and SFR. Connection of external devices uses ports 4 to 6. Ports 4 to 6 control address/data, read/write strobe, wait, address strobe, etc. Table 20-1. Pin Functions in External Memory Expansion Mode Pin Function When External Device Is Connected Name Alternate Function Function AD0 to AD7 Multiplexed address/data bus P40 to P47 A8 to A15 Address bus P50 to P57 RD Read strobe signal P64 WR Write strobe signal P65 WAIT Wait signal P66 ASTB Address strobe signal P67 Table 20-2. State of Port 4 to 6 Pins in External Memory Expansion Mode Port Port 4 External Expansion Mode 0 1 2 3 4 Port 6 5 6 7 4 5 6 7 Single-chip mode Port Port Port 256-byte expansion mode Address/data Port RD, WR, WAIT, ASTB 4 KB expansion mode Address/data Address 16 KB expansion mode Address/data Address Full-address mode Address/data Address Caution 420 0 to 7 Port 5 Port RD, WR, WAIT, ASTB Port RD, WR, WAIT, ASTB RD, WR, WAIT, ASTB When the external wait function is not used, the WAIT pin can be used as a port in all modes. User's Manual U14046EJ5V0UD CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION The memory maps when the external device expansion function is used are as follows. Figure 20-1. Memory Map When Using External Device Expansion Function (1/2) (a) Memory map of PD780021A, 780031A, 780021AY, (b) Memory map of PD780022A, 780032A, 780022AY, 780031AY and of PD78F0034A, 78F0034AY when 780032AY and of PD78F0034A, 78F0034AY when internal ROM (flash memory) size is 8 KB internal ROM (flash memory) size is 16 KB FFFFH FFFFH SFR SFR FF00H FEFFH FF00H FEFFH Internal high-speed RAM Internal high-speed RAM FD00H FCFFH FD00H FCFFH Reserved Reserved F800H F7FFH F800H F7FFH Full-address mode (when MM2 to MM0 = 111) Full-address mode (when MM2 to MM0 = 111) 8000H 7FFFH 6000H 5FFFH 16 KB expansion mode (when MM2 to MM0 = 101) 16 KB expansion mode (when MM2 to MM0 = 101) 5000H 4FFFH 4 KB expansion mode (when MM2 to MM0 = 100) 3000H 2FFFH 4 KB expansion mode (when MM2 to MM0 = 100) 2100H 20FFH 2000H 1FFFH 256-byte expansion mode (when MM2 to MM0 = 011) 4100H 40FFH 4000H 3FFFH 256-byte expansion mode (when MM2 to MM0 = 011) Single-chip mode Single-chip mode 0000H 0000H User's Manual U14046EJ5V0UD 421 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Figure 20-1. Memory Map When Using External Device Expansion Function (2/2) (c) Memory map of PD780023A, 780033A, 780023AY, (d) Memory map of PD780024A, 780034A, 780024AY, 780033AY and of PD78F0034A, 78F0034AY when 780034AY and of PD78F0034A, 78F0034AY when internal ROM (flash memory) size is 24 KB internal ROM (flash memory) size is 32 KB FFFFH FFFFH SFR FF00H FEFFH SFR FF00H FEFFH Internal high-speed RAM FB00H FAFFH Internal high-speed RAM FB00H FAFFH Reserved F800H F7FFH Reserved F800H F7FFH Full-address mode (when MM2 to MM0 = 111) Full-address mode (when MM2 to MM0 = 111) C000H BFFFH A000H 9FFFH 16 KB expansion mode (when MM2 to MM0 = 101) 16 KB expansion mode (when MM2 to MM0 = 101) 9000H 8FFFH 4 KB expansion mode (when MM2 to MM0 = 100) 7000H 6FFFH 4 KB expansion mode (when MM2 to MM0 = 100) 6100H 60FFH 6000H 5FFFH 256-byte expansion mode (when MM2 to MM0 = 011) 8100H 80FFH 8000H 7FFFH 256-byte expansion mode (when MM2 to MM0 = 011) Single-chip mode Single-chip mode 0000H 422 0000H User's Manual U14046EJ5V0UD CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION 20.2 External Device Expansion Function Control Registers The external device expansion function is controlled by the following two registers. * Memory expansion mode register (MEM) * Memory expansion wait setting register (MM) (1) Memory expansion mode register (MEM) MEM sets the external expansion area. MEM is set by a 1-bit or 8-bit memory manipulation instruction. RESET input clears MEM to 00H. Figure 20-2. Format of Memory Expansion Mode Register (MEM) Address: FF47H After reset: 00H R/W Symbol 7 6 5 4 3 2 1 0 MEM 0 0 0 0 0 MM2 MM1 MM0 MM2 MM1 MM0 Single-chip/memory P40 to P47, P50 to P57, P64 to P67 pin state expansion mode selection P40 to P47 P50 to P53 P54, P55 P56, P57 P64 to P67 0 0 0 Single-chip mode 0 0 1 Port 4 falling edge detection mode 0 1 1 Memory 256-byte expansion mode 1 0 0 1 0 1 16 KB mode 1 1 1 Full-address modeNote 2 Other than above Notes 1. Port mode AD0 to AD7 Port mode modeNote 1 4 KB mode P64 = RD P65 = WR P66 =WAIT P67 = ASTB A8 to A11 Port mode A12, A13 Port mode A14, A15 Setting prohibited When the memory expansion mode is set, if an area other than the external expansion area is accessed, the read value is undefined. 2. The full-address mode allows external expansion to the entire 64 KB address space except for the internal ROM, RAM, and SFR areas, and the reserved areas. Caution When using the falling edge detection function of port 4, be sure to set MEM to 01H. User's Manual U14046EJ5V0UD 423 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION (2) Memory expansion wait setting register (MM) MM sets the number of waits. MM is set by a 1-bit or 8-bit memory manipulation instruction. RESET input sets MM to 10H. Figure 20-3. Format of Memory Expansion Wait Setting Register (MM) Address: FFF8H After reset: 10H R/W Symbol 7 6 5 4 3 2 1 0 MM 0 0 PW1 PW0 0 0 0 0 PW1 PW0 0 0 No wait 0 1 Wait (one wait state inserted) 1 0 Setting prohibited 1 1 Wait control by external wait pin Wait control Cautions 1. When wait is controlled by the external wait pin, be sure to set the WAIT/P66 pin to input mode (set bit 6 (PM66) of port mode register 6 (PM6) to 1). 2. When wait is not controlled by the external wait pin, the WAIT/P66 pin can be used as an I/O port pin. 424 User's Manual U14046EJ5V0UD CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION 20.3 External Device Expansion Function Timing Timing control signal output pins in the external memory expansion mode are as follows. (1) RD pin (Alternate function: P64) Read strobe signal output pin. The read strobe signal is output in data read and instruction fetch from external memory. During internal memory read, the read strobe signal is not output (maintains high level). (2) WR pin (Alternate function: P65) Write strobe signal output pin. The write strobe signal is output in data write to external memory. During internal memory write, the write strobe signal is not output (maintains high level). (3) WAIT pin (Alternate function: P66) External wait signal input pin. When the external wait is not used, the WAIT pin can be used as an I/O port. During internal memory access, the external wait signal is ignored. (4) ASTB pin (Alternate function: P67) Address strobe signal output pin. The address strobe signal is output regardless of data access and instruction fetch from external memory. During internal memory access, the address strobe signal is output. (5) AD0 to AD7, A8 to A15 pins (Alternate function: P40 to P47, P50 to P57) Address/data signal output pins. Valid signal is output or input during data accesses and instruction fetches from external memory. These signals change even during internal memory access (output values are undefined). The timing charts are shown in Figures 20-4 to 20-7. User's Manual U14046EJ5V0UD 425 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Figure 20-4. Instruction Fetch from External Memory (a) No wait (PW1, PW0 = 0, 0) setting ASTB RD AD0 to AD7 Lower address Instruction code Higher address A8 to A15 (b) Wait (PW1, PW0 = 0, 1) setting ASTB RD AD0 to AD7 Lower address Instruction code Higher address A8 to A15 Internal wait signal (1-clock wait) (c) External wait (PW1, PW0 = 1, 1) setting ASTB RD AD0 to AD7 A8 to A15 Lower address Instruction code Higher address WAIT 426 User's Manual U14046EJ5V0UD CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Figure 20-5. External Memory Read Timing (a) No wait (PW1, PW0 = 0, 0) setting ASTB RD AD0 to AD7 Lower address Read data Higher address A8 to A15 (b) Wait (PW1, PW0 = 0, 1) setting ASTB RD AD0 to AD7 Lower address A8 to A15 Read data Higher address Internal wait signal (1-clock wait) (c) External wait (PW1, PW0 = 1, 1) setting ASTB RD AD0 to AD7 A8 to A15 Lower address Read data Higher address WAIT User's Manual U14046EJ5V0UD 427 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Figure 20-6. External Memory Write Timing (a) No wait (PW1, PW0 = 0, 0) setting ASTB WR Hi-Z Lower address AD0 to AD7 Write data Higher address A8 to A15 (b) Wait (PW1, PW0 = 0, 1) setting ASTB WR Lower address AD0 to AD7 Hi-Z Write data Higher address A8 to A15 Internal wait signal (1-clock wait) (c) External wait (PW1, PW0 = 1, 1) setting ASTB WR AD0 to AD7 A8 to A15 Lower address Hi-Z Write data Higher address WAIT 428 User's Manual U14046EJ5V0UD CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Figure 20-7. External Memory Read Modify Write Timing (a) No wait (PW1, PW0 = 0, 0) setting ASTB RD WR AD0 to AD7 Lower address Hi-Z Read data Write data Higher address A8 to A15 (b) Wait (PW1, PW0 = 0, 1) setting ASTB RD WR AD0 to AD7 Lower address A8 to A15 Hi-Z Read data Write data Higher address Internal wait signal (1-clock wait) (c) External wait (PW1, PW0 = 1, 1) setting ASTB RD WR AD0 to AD7 A8 to A15 Lower address Hi-Z Read data Write data Higher address WAIT Remark The read-modify-write timing is that of an operation when a bit manipulation instruction is executed. User's Manual U14046EJ5V0UD 429 CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION 20.4 Example of Connection with Memory This section provide an example of connecting the PD780024A with external memory (in this example, SRAM) in Figure 20-8. In addition, the external device expansion function is used in the full-address mode, and the addresses from 0000H to 7FFFH (32 KB) are allocated for internal ROM, and the addresses after 8000H for SRAM. Figure 20-8. Connection Example of PD780024A and Memory VDD0 PD780024A PD43256B CS OE RD WE I/O1 to I/O8 WR Address bus A8 to A14 ASTB A0 to A14 74HC573 LE Q0 to Q7 AD0 to AD7 430 D0 to D7 OE User's Manual U14046EJ5V0UD Data bus CHAPTER 21 STANDBY FUNCTION 21.1 Standby Function and Configuration 21.1.1 Standby function The standby function is designed to decrease power consumption of the system. The following two modes are available. (1) HALT mode HALT instruction execution sets the HALT mode. The HALT mode stops the CPU operation clock. The system clock oscillator continues oscillating. In this mode, power consumption is not decreased as much as in the STOP mode. However, the HALT mode is effective to restart operation immediately upon an interrupt request and to carry out intermittent operations. (2) STOP mode STOP instruction execution sets the STOP mode. In the STOP mode, the main system clock oscillator stops, stopping the whole system, thereby considerably reducing the CPU power consumption. Data memory low-voltage hold (down to VDD = 1.6 V) is possible. Thus, the STOP mode is effective to hold data memory contents with ultra-low power consumption. Because this mode can be released upon an interrupt request, it enables intermittent operations to be carried out. However, because a wait time is required to stabilize oscillation after the STOP mode is released, select the HALT mode if it is necessary to start processing immediately upon an interrupt request. In either of these two modes, all the contents of registers, flags and data memory just before the standby mode is set are held. The I/O port output latches and output buffer statuses are also held. Cautions 1. The STOP mode can be used only when the system operates with the main system clock (subsystem clock oscillation cannot be stopped). The HALT mode can be used with either the main system clock or the subsystem clock. 2. When operation is transferred to the STOP mode, be sure to stop operation of the peripheral hardware operating with the main system clock before executing the STOP instruction. 3. The following sequence is recommended for reducing the power consumption of the A/D converter when the standby function is used: First clear bit 7 (ADCS0) of A/D converter mode register 0 (ADM0) to 0 to stop the A/D conversion operation, and then execute the HALT or STOP instruction. User's Manual U14046EJ5V0UD 431 CHAPTER 21 STANDBY FUNCTION 21.1.2 Standby function control register The wait time after the STOP mode is released upon an interrupt request is controlled by the oscillation stabilization time select register (OSTS). OSTS is set by an 8-bit memory manipulation instruction. RESET input sets OSTS to 04H. Therefore, when the STOP mode is released by inputting RESET, it takes 217/ fX until release. Figure 21-1. Format of Oscillation Stabilization Time Select Register (OSTS) Address: FFFAH After reset: 04H R/W Symbol 7 6 5 4 3 2 1 0 OSTS 0 0 0 0 0 OSTS2 OSTS1 OSTS0 OSTS2 OSTS1 OSTS0 Selection of oscillation stabilization time fX = 8.38 MHz 0 0 0 0 0 1 fX = 12 MHzNote 0 212/fX 488 s 341 s 1 214/fX 1.95 ms 1.36 ms 0 215/fX 3.91 ms 2.73 ms 7.82 ms 5.46 ms 15.6 ms 10.9 ms 0 1 1 216/fX 1 0 0 217/fX Other than above Setting prohibited Note Expanded-specification products of PD780024A, 780034A Subseries only. Caution The wait time after the STOP mode is released does not include the time (see "a" in the illustration below) from STOP mode release to clock oscillation start. This applies regardless of whether STOP mode is released by RESET input or by interrupt request generation. STOP mode release X1 pin voltage waveform a Remark fX: Main system clock oscillation frequency 432 User's Manual U14046EJ5V0UD CHAPTER 21 STANDBY FUNCTION 21.2 Standby Function Operations 21.2.1 HALT mode (1) HALT mode setting and operating statuses The HALT mode is set by executing the HALT instruction. It can be set with the main system clock or the subsystem clock. The operating statuses in the HALT mode are described below. Table 21-1. HALT Mode Setting HALT Mode Operating Statuses HALT Instruction Execution When Using Main System Clock Without Subsystem ClockNote 1 HALT Instruction Execution When Using Subsystem Clock With Subsystem ClockNote 2 With Main System Clock Oscillation Item With Main System Clock Oscillation Stopped Clock generator Both main system clock and subsystem clock can be oscillated. Clock supply to CPU stops. CPU Operation stops. Ports (output latches) Status before HALT mode setting is held. 16-bit timer/event counter 0 Operable Stop 8-bit timer/event counters 50, 51 Operable Operable when TI50, TI51 are selected as count clock. Watch timer Operable when fX/27 is Operable selected as count clock. Operable when fXT is selected as count clock. Watchdog timer Operable Clock output Operable when fX to Operation stops. fX/27 Operable Operable when fXT is is selected as output clock. selected as output clock. Buzzer output Operable BUZ is at low level. A/D converter Stop Serial interface Operable External interrupt Operable Operable during external clock input. Bus line AD0 to AD7 High impedance during A8 to A15 Status before HALT mode setting is held. external expansion ASTB Low level WR, RD High level WAIT High impedance Notes 1. Including case when external clock is not supplied. 2. Including case when external clock is supplied. User's Manual U14046EJ5V0UD 433 CHAPTER 21 STANDBY FUNCTION (2) HALT mode release The HALT mode can be released with the following three types of sources. (a) Release by unmasked interrupt request When an unmasked interrupt request is generated, the HALT mode is released. If interrupt acknowledge is enabled, vectored interrupt service is carried out. If interrupt acknowledge is disabled, the next address instruction is executed. Figure 21-2. HALT Mode Release by Interrupt Request Generation Interrupt request HALT instruction Wait Standby release signal Operating mode HALT mode Wait Operating mode Oscillation Clock Remarks 1. The broken line indicates the case when the interrupt request which has released the standby mode is acknowledged. 2. Wait times are as follows: * When vectored interrupt service is carried out: 8 or 9 clocks * When vectored interrupt service is not carried out: 2 or 3 clocks (b) Release by non-maskable interrupt request When a non-maskable interrupt request is generated, the HALT mode is released and vectored interrupt service is carried out whether interrupt acknowledge is enabled or disabled. However, a non-maskable interrupt request is not generated during subsystem clock operation. 434 User's Manual U14046EJ5V0UD CHAPTER 21 STANDBY FUNCTION (c) Release by RESET input When RESET signal is input, HALT mode is released. And, as in the case with normal reset operation, a program is executed after branch to the reset vector address. Figure 21-3. HALT Mode Release by RESET Input Wait (217/fX: 15.6 ms) HALT instruction RESET signal Operating mode Reset period HALT mode Oscillation Clock Oscillation stabilization wait status Oscillation stop Operating mode Oscillation Remarks 1. fX: Main system clock oscillation frequency 2. Values in parentheses are for operation with fX = 8.38 MHz. Table 21-2. Release Source Operation After HALT Mode Release MKxx PRxx IE ISP 0 0 0 x Next address instruction execution 0 0 1 x Interrupt service execution 0 1 0 1 Next address instruction execution 0 1 x 0 0 1 1 1 Interrupt service execution 1 x x x HALT mode hold Non-maskable interrupt request - - x x Interrupt service execution RESET input - - x x Reset processing Maskable interrupt request Operation x: don't care User's Manual U14046EJ5V0UD 435 CHAPTER 21 STANDBY FUNCTION 21.2.2 STOP mode (1) STOP mode setting and operating statuses The STOP mode is set by executing the STOP instruction. It can be set only with the main system clock. Cautions 1. When the STOP mode is set, the X2 pin is internally connected to VDD1 via a pull-up resistor to minimize the leakage current at the crystal oscillator. Thus, do not use the STOP mode in a system where an external clock is used for the main system clock. 2. Because the interrupt request signal is used to clear the standby mode, if there is an interrupt source with the interrupt request flag set and the interrupt mask flag reset, the standby mode is immediately cleared if set. Thus, the STOP mode is reset to the HALT mode immediately after execution of the STOP instruction. The operating mode is set after the wait set using the oscillation stabilization time select register (OSTS). The operating statuses in the STOP mode are described below. Table 21-3. STOP Mode Setting STOP Mode Operating Statuses With Subsystem Clock Without Subsystem Clock Item Clock generator Only main system clock oscillation is stopped. CPU Operation stops. Ports (output latches) Status before STOP mode setting is held. 16-bit timer/event counter 0 Operation stops. 8-bit timer/event counters 50, 51 Operable only when TI50, TI51 are selected as count clock. Watch timer Operable only when fXT is selected as count clock. Watchdog timer Operation stops. Clock output Operable when fXT is selected as output clock. Buzzer output BUZ is at low level. A/D converter Operation stops. Serial interface PCL is at low level. Other than UART0 Operable only when externally supplied clock is specified as the serial clock. UART0 Operation stops. (Transmit shift register 0 (TXS0), receive shift register 0 (RX0), and receive buffer register 0 (RXB0) hold the value just before the clock stopped.) External interrupt Operable Bus line during AD0 to AD7 High impedance external expansion A8 to A15 Status before STOP mode setting is held. ASTB Low level WR, RD High level WAIT High impedance 436 Operation stops. User's Manual U14046EJ5V0UD CHAPTER 21 STANDBY FUNCTION (2) STOP mode release The STOP mode can be released by the following two types of sources. (a) Release by unmasked interrupt request When an unmasked interrupt request is generated, the STOP mode is released. If interrupt acknowledge is enabled after the lapse of oscillation stabilization time, vectored interrupt service is carried out. If interrupt acknowledge is disabled, the next address instruction is executed. Figure 21-4. STOP Mode Release by Interrupt Request Generation Interrupt request Wait (Time set by OSTS) STOP instruction Standby release signal Operating mode Clock Oscillation STOP mode Oscillation stabilization wait status Oscillation stop Oscillation Operating mode Remark The broken line indicates the case when the interrupt request which has released the standby mode is acknowledged. User's Manual U14046EJ5V0UD 437 CHAPTER 21 STANDBY FUNCTION (b) Release by RESET input The STOP mode is released when RESET signal is input, and after the lapse of oscillation stabilization time, reset operation is carried out. Figure 21-5. STOP Mode Release by RESET Input Wait (217/fX: 15.6 ms) STOP instruction RESET signal Operating mode Clock Reset period STOP mode Oscillation Oscillation stabilization wait status Operating mode Oscillation Oscillation stop Remarks 1. fX: Main system clock oscillation frequency 2. Values in parentheses are for operation with fX = 8.38 MHz. Table 21-4. Release Source Maskable interrupt request RESET input Operation After STOP Mode Release MKxx PRxx IE ISP 0 0 0 x Next address instruction execution 0 0 1 x Interrupt service execution 0 1 0 1 Next address instruction execution 0 1 x 0 0 1 1 1 Interrupt service execution 1 x x x STOP mode hold - - x x Reset processing x: don't care 438 User's Manual U14046EJ5V0UD Operation CHAPTER 22 RESET FUNCTION The following two operations are available to generate the reset signal. (1) External reset input via RESET pin (2) Internal reset by watchdog timer program loop time detection External reset and internal reset have no functional differences. In both cases, program execution starts at the address at 0000H and 0001H by RESET input. When a low level is input to the RESET pin or the watchdog timer overflows, a reset is applied and each hardware is set to the status shown in Table 22-1. Each pin has high impedance during reset input or during oscillation stabilization time just after reset release. When a high level is input to the RESET pin, the reset is released and program execution starts after the lapse of oscillation stabilization time (217/fX). The reset applied by watchdog timer overflow is automatically released after a reset and program execution starts after the lapse of oscillation stabilization time (217/fX) (see Figures 22-2 to 22-4). Cautions 1. For an external reset, input a low level for 10 s or more to the RESET pin. 2. During reset input, main system clock oscillation remains stopped but subsystem clock oscillation continues. 3. When the STOP mode is released by reset, the STOP mode contents are held during reset input. However, the port pin becomes high impedance. Figure 22-1. Reset Function Block Diagram RESET Count clock Reset signal Reset controller Watchdog timer Overflow Interrupt function Stop User's Manual U14046EJ5V0UD 439 CHAPTER 22 RESET FUNCTION Figure 22-2. Timing of Reset by RESET Input X1 Oscillation stabilization time wait Reset period (Oscillation stop) Normal operation Normal operation (Reset processing) RESET Internal reset signal Delay Delay Hi-Z Port pin Figure 22-3. Timing of Reset Due to Watchdog Timer Overflow X1 Oscillation stabilization time wait Reset period (Oscillation stop) Normal operation Watchdog timer overflow Normal operation (Reset processing) Internal reset signal Hi-Z Port pin Figure 22-4. Timing of Reset in STOP Mode by RESET Input X1 STOP instruction execution Normal operation Stop status (Oscillation stop) Reset period (Oscillation stop) Oscillation stabilization time wait RESET Internal reset signal Delay Delay Hi-Z Port pin 440 User's Manual U14046EJ5V0UD Normal operation (Reset processing) CHAPTER 22 RESET FUNCTION Table 22-1. Hardware Statuses After Reset (1/2) Hardware Program counter Status After Reset (PC)Note 1 Contents of reset vector table (0000H, 0001H) are set. Stack pointer (SP) Undefined Program status word (PSW) RAM 02H Data memory UndefinedNote 2 General-purpose register UndefinedNote 2 Port (output latch) 00H Port mode registers 0, 2 to 7 (PM0, PM2 to PM7) FFH Pull-up resistor option registers 0, 2 to 7 (PU0, PU2 to PU7) 00H Processor clock control register (PCC) 04H CFHNote 3 Memory size switching register (IMS) Memory expansion mode register (MEM) 00H Memory expansion wait setting register (MM) 10H Oscillation stabilization time select register (OSTS) 04H 16-bit timer/event counter 0 Timer counter 0 (TM0) 0000H Capture/compare registers 00, 01 (CR00, CR01) 8-bit timer/event counters 50, 51 Undefined Prescaler mode register 0 (PRM0) 00H Capture/compare control register 0 (CRC0) 00H Mode control register 0 (TMC0) 00H Output control register 0 (TOC0) 00H Timer counters 50, 51 (TM50, TM51) 00H Compare registers 50, 51 (CR50, CR51) Undefined Clock select registers 50, 51 (TCL50, TCL51) 00H Mode control registers 50, 51 (TMC50, TMC51) 00H Watch timer Operation mode register (WTM) 00H Watchdog timer Clock select register (WDCS) 00H Mode register (WDTM) 00H Notes 1. During reset input or oscillation stabilization time wait, only the PC contents among the hardware statuses become undefined. All other hardware statuses remain unchanged after reset. 2. When a reset is executed in the standby mode, the pre-reset status is held even after reset. 3. Although the initial value is CFH, set the following values in the initial settings for each version. PD780021A, 780021AY, 780031A, 780031AY: 42H PD780022A, 780022AY, 780032A, 780032AY: 44H PD780023A, 780023AY, 780033A, 780033AY: C6H PD780024A, 780024AY, 780034A, 780034AY: C8H PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY: Value for mask ROM versions User's Manual U14046EJ5V0UD 441 CHAPTER 22 RESET FUNCTION Table 22-1. Hardware Statuses After Reset (2/2) Hardware Status After Reset Clock output/buzzer output controller Clock output select register (CKS) 00H A/D converter Conversion result register 0 (ADCR0) 00H Mode register 0 (ADM0) 00H Analog input channel specification register 0 (ADS0) 00H Asynchronous serial interface mode register 0 (ASIM0) 00H Asynchronous serial interface status register 0 (ASIS0) 00H Baud rate generator control register 0 (BRGC0) 00H Transmit shift register 0 (TXS0) FFH Serial interface UART0 Receive buffer register 0 (RXB0) Serial interfaces SIO30, SIO31Note 1 Serial interface IIC0Note 2 Interrupt Shift registers 30, 31 (SIO30, SIO31) Undefined Operation mode registers 30, 31 (CSIM30, CSIM31) 00H Transfer clock select register 0 (IICCL0) 00H Shift register 0 (IIC0) 00H Control register 0 (IICC0) 00H Status register 0 (IICS0) 00H Slave address register 0 (SVA0) 00H Request flag registers 0L, 0H, 1L (IF0L, IF0H, IF1L) 00H Mask flag registers 0L, 0H, 1L (MK0L, MK0H, MK1L) FFH Priority specification flag registers 0L, 0H, 1L (PR0L, PR0H, PR1L) FFH External interrupt rising edge enable register (EGP) 00H External interrupt falling edge enable register (EGN) 00H Notes 1. Serial interface SIO31 is provided only in the PD780024A, 780034A Subseries. 2. Serial interface IIC0 is provided only in the PD780024AY, 780034AY Subseries. 442 User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY The PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY are provided as the flash memory versions of the PD780024A, 780034A, 780024AY, 780034AY Subseries. The PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY are products that incorporate flash memory in which the program can be written, erased, and rewritten while it is mounted on the board. Writing to flash memory can be performed with the memory mounted on the target system (on board). A dedicated flash programmer is connected to the target system to perform writing. The following can be considered as the development environment and the applications using flash memory. * Software can be altered after the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY are soldermounted on the target system. * * Small scale production of various models is made easier by differentiating software. Data adjustment in starting mass production is made easier. Table 23-1 shows the correspondence between PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY and the mask ROM versions. Table 23-1. Correspondence Between PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY, and Mask ROM Versions Mask ROM Version PD780021A/22A/ 23A/24A/31A/32A/ 33A/34A PD780021A(A)/ 22A(A)/23A(A)/24A(A)/ 31A(A)/32A(A)/33A(A)/ 34A(A) PD780021AY/ 22AY/23AY/24AY/ 31AY/32AY/33AY/ 34AY PD780021AY(A)/ 22AY(A)/23AY(A)/ 24AY(A)/31AY(A)/ 32AY(A)/33AY(A)/ 34AY(A) Conventional Expanded- Conventional ExpandedProducts Specification Products Specification Products Products Flash Memory Version PD78F0034A - PD78F0034B - - - - - - - - - - - PD78F0034B(A) - - Note PD78F0034AY - - - - - PD78F0034BY - - - - - PD78F0034BY(A) - - - - - Note The PD78F0034B(A) and the conventional products of the PD780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), and 780034A(A) differ in the operating frequency. When replacing a flash memory version with a mask ROM version, note the supply voltage and operating frequency. Remarks 1. : Supported, -: Not supported 2. Expanded-specification products and conventional products of the PD780024A and 780034A Subseries differ in operating frequency ratings. For details, refer to the description of electrical specifications. 3. Expanded-specification products of the PD780024AY, 780034AY Subseries are not available. Only conventional products are available. 4. A special grade product of the PD78F0034A, 78F0034AY is not available. Only a standard grade product is available. User's Manual U14046EJ5V0UD 443 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.1 Differences Between PD78F0034A, 78F0034AY and PD78F0034B, 78F0034BY Table 23-2 shows the differences between the PD78F0034A and PD78F0034B, and Table 23-3 shows differences between the PD78F0034AY and PD78F0034BY. Table 23-2. Differences Between PD78F0034A and PD78F0034B PD78F0034A Item PD78F0034B Guaranteed operating speed 4.5 to 5.5 V 8.38 MHz (0.238 s) 12 MHz (0.166 s) (operating frequency) 4.0 to 5.5 V 8.38 MHz (0.238 s) 8.38 MHz (0.238 s) 3.0 to 5.5 V 5 MHz (0.4 s) 8.38 MHz (0.238 s) 2.7 to 5.5 V 5 MHz (0.4 s) 5 MHz (0.4 s) 1.8 to 5.5 V 1.25 MHz (1.6 s) 1.25 MHz (1.6 s) Minimum instruction execution time Minimum instruction execution time variable function incorporated When main system clock is selected 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@ 8.38 MHz operation, VDD = 4.0 to 5.5 V) When subsystem clock is selected 122 s (32.768 kHz) 0.166 s/0.333 s/0.666 s/1.33 s/2.66 s (@ 12 MHz operation, VDD = 4.5 to 5.5 V) Clock output * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (@ 8.38 MHz operation with main system clock) * 32.768 kHz (@ 32.768 kHz operation with subsystem clock) * 93.7 kHz, 187 kHz, 375 kHz, 750 kHz, 1.5 MHz, 3 MHz, 6 MHz, 12 MHz (@ 12 MHz operation with main system clock) * 32.768 kHz (@ 32.768 kHz operation with subsystem clock) Buzzer output 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (@ 8.38 MHz operation with main system clock) 1.46 kHz, 2.92 kHz, 5.85 kHz, 11.7 kHz (@ 12 MHz operation with main system clock) Communication mode of flash memory programming * 3-wire serial I/O: 2 channels * UART: 1 channel * Pseudo 3-wire serial I/O: 1 channel Electrical specifications, recommended soldering conditions Refer to the description of electrical specifications and recommended soldering conditions. Note * 3-wire serial I/O: 2 channels * UART: 1 channel * Pseudo 3-wire serial I/O: 1 channel Note Note The PD78F0034A cannot use a handshake mode. The PD78F0034B can use one channel (serial interface SIO30) as a handshake mode. Remark The operating frequency ratings of the PD78F0034A and the conventional products of the mask ROM versions of the PD780024A, 780034A Subseries are the same. The operating frequency ratings of the PD78F0034B and the expanded-specification products of the mask ROM versions of the PD780024A, 780034A Subseries are the same. 444 User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Table 23-3. Differences Between PD78F0034AY and PD78F0034BY PD78F0034AY Item Guaranteed operating speed 4.5 to 5.5 V 8.38 MHz (0.238 s) (operating frequency) 4.0 to 5.5 V 8.38 MHz (0.238 s) 3.0 to 5.5 V 5 MHz (0.4 s) 2.7 to 5.5 V 5 MHz (0.4 s) 1.8 to 5.5 V 1.25 MHz (1.6 s) Minimum instruction execution time PD78F0034BY Minimum instruction execution time variable function incorporated When main system clock is selected 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@ 8.38 MHz operation, VDD = 4.0 to 5.5 V) When subsystem clock is selected 122 s (32.768 kHz) Clock output * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (@ 8.38 MHz operation with main system clock) * 32.768 kHz (@ 32.768 kHz operation with subsystem clock) Buzzer output 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (@ 8.38 MHz operation with main system clock) Note Communication mode of flash memory programming * 3-wire serial I/O: 2 channels * UART: 1 channel * Pseudo 3-wire serial I/O: 1 channel * 3-wire serial I/O: 2 channels * UART: 1 channel * Pseudo 3-wire serial I/O: 1 channel Electrical specifications, recommended soldering conditions Refer to the description of electrical specifications and recommended soldering conditions. Note Note The PD78F0034AY cannot use a handshake mode. The PD78F0034BY can use one channel (serial interface SIO30) as a handshake mode. Remark The operating frequency ratings of the PD78F0034AY, 78F0034BY and the mask ROM versions of the PD780024AY, 780034AY Subseries are the same. 23.2 Differences Between PD78F0034B, 78F0034BY and PD78F0034B(A), 78F0034BY(A) The PD78F0034B(A) and 78F0034BY(A) are products to which a quality assurance program more stringent than that used for the PD78F0034B and 78F0034BY (standard products) is applied (NEC Electronics classifies these products as "special" quality grade products). The PD78F0034B, 78F0034BY and PD78F0034B(A), 78F0034BY(A) only differ in the quality grade; there are no differences in functions and electrical specifications. Table 23-4. Differences Between PD78F0034B, 78F0034BY and PD78F0034B(A), 78F0034BY(A) Item PD78F0034B, 78F0034BY Quality grade Standard Functions and electrical specifications No differences. PD78F0034B(A), 78F0034BY(A) Special This chapter explains the PD78F0034B as the representative product of the PD78F0034B and 78F0034B(A), and the PD78F0034BY as the representative product of the PD78F0034BY and 78F0034BY(A). User's Manual U14046EJ5V0UD 445 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.3 Differences Between PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY and Mask ROM Versions Tables 23-5 and 23-6 show the differences between the PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY and the mask ROM versions. Table 23-5. Differences Between PD78F0034A, 78F0034B and Mask ROM Versions Item PD78F0034A, 78F0034B Mask ROM Versions PD780034A Subseries PD780024A SubseriesNote Internal ROM structure Flash memory Mask ROM Internal ROM capacity 32 KB PD780031A: PD780032A: PD780033A: PD780034A: 8 KB 16 KB 24 KB 32 KB PD780021A: PD780022A: PD780023A: PD780024A: 8 KB 16 KB 24 KB 32 KB Internal high-speed RAM capacity 1,024 bytes PD780031A: PD780032A: PD780033A: PD780034A: 512 bytes 512 bytes 1,024 bytes 1,024 bytes PD780021A: PD780022A: PD780023A: PD780024A: 512 bytes 512 bytes 1,024 bytes 1,024 bytes Minimum instruction execution time Minimum instruction execution time variable function incorporated When main system clock is selected * 0.166 s/0.333 s/0.666 s/1.33 s/2.66 s (@ 12 MHz operation, PD78F0034B and expanded-specification products of the mask ROM versions only) * 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@ 8.38 MHz operation) When subsystem clock is selected 122 s (@32.768 kHz operation) Clock output * 93.7 kHz, 187 kHz, 375 kHz, 750 kHz, 1.5 MHz, 3 MHz, 6 MHz, 12 MHz (@ 12 MHz operation with main system clock, PD78F0034B and expandedspecification products of the mask ROM versions only) * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (@ 8.38 MHz operation with main system clock) * 32.768 kHz (@ 32.768 kHz operation with subsystem clock) Buzzer output * 1.46 kHz, 2.92 kHz, 5.85 kHz, 11.7 kHz (@ 12 MHz operation with main system clock, PD78F0034B and expanded-specification products of the mask ROM versions only) * 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (@ 8.38 MHz operation with main system clock) A/D converter resolution 10 bits Mask option specification of on-chip pull-up resistor for pins P30 to P33 Not available Available IC pin Not provided Provided VPP pin Provided Not provided Electrical specifications, recommended soldering conditions Refer to the description of electrical specifications and recommended soldering conditions. 8 bits Note The PD78F0034A and 78F0034B can be used as the flash memory version of the PD780024A Subseries. Caution There are differences in noise immunity and noise radiation between the flash memory and mask ROM versions. When pre-producing an application set with the flash memory version and then mass producing it with the mask ROM version, be sure to conduct sufficient evaluations on the commercial samples (CS) (not engineering samples (ES)) of the mask ROM versions. 446 User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Table 23-6. Differences Between PD78F0034AY, 78F0034BY and Mask ROM Versions Item PD78F0034AY, 78F0034BY Mask ROM Versions PD780034AY Subseries Internal ROM structure Flash memory Mask ROM Internal ROM capacity 32 KB PD780031AY: PD780032AY: PD780033AY: PD780034AY: 8 KB 16 KB 24 KB 32 KB PD780031AY: 512 bytes PD780032AY: 512 bytes PD780033AY: 1,024 bytes PD780034AY: 1,024 bytes PD780024AY SubseriesNote PD780021AY: PD780022AY: PD780023AY: PD780024AY: 8 KB 16 KB 24 KB 32 KB PD780021AY: 512 bytes PD780022AY: 512 bytes PD780023AY: 1,024 bytes PD780024AY: 1,024 bytes Internal high-speed RAM capacity 1,024 bytes Minimum instruction execution time Minimum instruction execution time variable function incorporated When main system clock is selected 0.238 s/0.477 s/0.954 s/1.90 s/3.81 s (@8.38 MHz operation) When subsystem clock is selected 122 s (@32.768 kHz operation) Clock output * 65.5 kHz, 131 kHz, 262 kHz, 524 kHz, 1.05 MHz, 2.10 MHz, 4.19 MHz, 8.38 MHz (@ 8.38 MHz operation with main system clock) * 32.768 kHz (@ 32.768 kHz operation with subsystem clock) Buzzer output 1.02 kHz, 2.05 kHz, 4.10 kHz, 8.19 kHz (@ 8.38 MHz operation with main system clock) A/D converter resolution 10 bits Mask option specification of on-chip Not available Available IC pin Not provided Provided VPP pin Provided Not provided Electrical specifications, recommended soldering conditions Refer to the description of electrical specifications and recommended soldering conditions. 8 bits pull-up resistor for pins P30 and P31 Note The PD78F0034AY and 78F0034BY can be used as the flash memory version of the PD780024AY Subseries. Caution There are differences in noise immunity and noise radiation between the flash memory and mask ROM versions. When pre-producing an application set with the flash memory version and then mass producing it with the mask ROM version, be sure to conduct sufficient evaluations on the commercial samples (CS) (not engineering samples (ES)) of the mask ROM versions. User's Manual U14046EJ5V0UD 447 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.4 Memory Size Switching Register The PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY allow users to select the internal memory capacity using the memory size switching register (IMS) so that the same memory map as that of the mask ROM versions with a different size of internal memory capacity can be achieved. IMS is set by an 8-bit memory manipulation instruction. RESET input sets IMS to CFH. Caution Be sure to set the value of the target mask ROM version to IMS as an initialization setting of the program. IMS is set to CFH by reset, so be sure to set the value of the target mask ROM version after reset. Figure 23-1. Format of Memory Size Switching Register (IMS) Address: FFF0H After reset: CFH R/W Symbol IMS 7 6 5 4 3 2 1 0 RAM2 RAM1 RAM0 0 ROM3 ROM2 ROM1 ROM0 RAM2 RAM1 RAM0 0 1 0 512 bytes 1 1 0 1024 bytes Other than above Internal high-speed RAM capacity selection Setting prohibited ROM3 ROM2 ROM1 ROM0 0 0 1 0 8 KB 0 1 0 0 16 KB 0 1 1 0 24 KB 1 0 0 0 32 KB 1 1 1 1 60 KB (setting prohibited) Other than above Internal ROM capacity selection Setting prohibited The IMS settings to obtain the same memory map as mask ROM versions are shown in Table 23-7. Table 23-7. Memory Size Switching Register Settings Target Mask ROM Versions Caution 448 IMS Setting PD780021A, 780031A, 780021AY, 780031AY 42H PD780022A, 780032A, 780022AY, 780032AY 44H PD780023A, 780033A, 780023AY, 780033AY C6H PD780024A, 780034A, 780024AY, 780034AY C8H When using the mask ROM versions, be sure to set the value indicated in Table 23-7 to IMS. User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.5 Flash Memory Characteristics Flash memory programming is performed by connecting a dedicated flash programmer (Flashpro III (part no. FLPR3, PG-FP3)/Flashpro IV (part no. FL-PR4, PG-FP4)) to the target system with the flash memory mounted on the target system (on-board). A flash memory writing adapter (program adapter), which is a target board used exclusively for programming, is also provided. Remark FL-PR3, FL-PR4, and the program adapter are products made by Naito Densei Machida Mfg. Co., Ltd. (TEL +81-45-475-4191). Programming using flash memory has the following advantages. * * * Software can be modified after the microcontroller is solder-mounted on the target system. Distinguishing software facilities low-quantity, varied model production Easy data adjustment when starting mass production 23.5.1 Programming environment The following shows the environment required for PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY flash memory programming. When Flashpro III or Flashpro IV is used as a dedicated flash programmer, a host machine is required to control the dedicated flash programmer. Communication between the host machine and flash programmer is performed via RS-232C/USB (Rev. 1.1). For details, refer to the manuals of Flashpro III/Flashpro IV. Remark USB is supported by Flashpro IV only. Figure 23-2. Environment for Writing Program to Flash Memory VPP USB XXXXXX VDD XXXX Bxxxxx Cxxxxxx STATVE PG-FP4 (Flash Pro4) XXXXX XXXX YYYY Axxxx XXX YYY RS-232C VSS RESET Dedicated flash SIO/UART/pseudo 3-wire/IICNote programmer Host machine PD78F0034A, PD78F0034B, PD78F0034AY, PD78F0034BY Note IIC is supported by the PD78F0034AY, 78F0034BY only. User's Manual U14046EJ5V0UD 449 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.5.2 Communication mode Use the communication mode shown in Table 23-8 to perform communication between the dedicated flash programmer and the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY. Table 23-8. Communication Mode List (1/2) (1) PD78F0034A, 78F0034B Communication Mode Standard (TYPE) SettingNote 1 Port (COMM PORT) Speed (SIO CLOCK) On Target (CPU CLOCK) 2.4 kHz to 625 kHzNote 2 Optional (100 Hz to 1.25 MHz)Note 2 Pins Used Number of VPP Pulses SI30/P20 SO30/P21 SCK30/P22 0 Frequency Multiply (Flashpro Rate Clock) (Multiple Rate) 1 to 10 MHzNote 2 1.0 3-wire serial I/O (SIO30) SIO-ch0 (SIO ch-0) 3-wire serial I/O (SIO31) SIO-ch1 (SIO ch-1) SI31/P34 SO31/P35 SCK31/P36 1 3-wire serial I/O (SIO30) with handshake SIO-H/S (SIO ch-0 + handshake) SI30/P20 SO30/P21 SCK30/P22 HS/P25 3 Note 3 UART (UART0) UART-ch0 (UART ch-0) 4800 to 76800 BaudNotes 2, 4 (4800 to 76800 bps)Notes 2, 4 RXD0/P23 TXD0/P24 8 Pseudo 3-wire serial I/O Port-ch0 (Port A) 100 Hz to 1500 HzNote 2 (100 Hz to 1.25 MHz)Note 2 P70/TI00/TO0 (serial data input) P71/TI01 (serial data output) P72/TI50/TO50 (serial clock input) 12 Notes 1. Selection items for Standard settings on Flashpro IV (TYPE settings on Flashpro III). 2. The possible setting range differs depending on the voltage. For details, refer to the description of electrical specifications. 3. PD78F0034B only 4. Because factors other than the baud rate error, such as the signal waveform slew, also affect UART communication, thoroughly evaluate the slew as well as the baud rate error. Remark Items enclosed in parentheses in the setting item column are the set value and set item of Flashpro III when they differ from those of Flashpro IV. 450 User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Table 23-8. Communication Mode List (2/2) (2) PD78F0034AY, 78F0034BY Communication Mode Standard (TYPE) SettingNote 1 Port (COMM PORT) Speed (SIO CLOCK) On Target (CPU CLOCK) 2.4 kHz to 625 kHzNote 2 Optional (100 Hz to 1.25 MHz)Note 2 3-wire serial I/O (SIO30) SIO-ch0 (SIO ch-0) 3-wire serial I/O (SIO30) with handshake SIO-H/S (SIO ch-0 + handshake) Pins Used Number of VPP Pulses SI30/P20 SO30/P21 SCK30/P22 0 SI30/P20 SO30/P21 SCK30/P22 HS/P25 3 SDA0/P32 4 Frequency Multiply (Flashpro Rate Clock) (Multiple Rate) 1 to 10 MHzNote 2 1.0 Note 3 I2C bus IIC-ch0 (IIC0) (I2C 10 k to 100 k BandNote 2 UART UART-ch0 (UART ch-0) 4800 to 76800 BaudNotes 2, 4 (4800 to 76800 bps)Notes 2, 4 RXD0/P23 TXD0/P24 8 (UART0) Pseudo 3-wire serial I/O Port-ch0 (Port A) 100 Hz to 1500 HzNote 2 (100 Hz to 1.25 MHz)Note 2 P70/TI00/TO0 (serial data input) P71/TI01 (serial data output) P72/TI50/TO50 (serial clock input) 12 ch-0) (50 kHz)Note 2 SCL0/P33 Notes 1. Selection items for Standard settings on Flashpro IV (TYPE settings on Flashpro III). 2. The possible setting range differs depending on the voltage. For details, refer to the description of electrical specifications. 3. PD78F0034BY only 4. Because factors other than the baud rate error, such as the signal waveform slew, also affect UART communication, thoroughly evaluate the slew as well as the baud rate error. Remark Items enclosed in parentheses in the setting item column are the set value and set item of Flashpro III when they differ from those of Flashpro IV. Figure 23-3. Communication Mode Selection Format VPP pulse 10 V VPP VDD VSS VDD RESET VSS Flash memory write mode User's Manual U14046EJ5V0UD 451 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-4. Example of Connection with Dedicated Flash Programmer (1/2) (a) 3-wire serial I/O (SIO3nNote 1) Dedicated flash programmer Flash memory version VPP VPP VDD VDD0Note 4, VDD1Note 4, AVDD /RESET RESET SCK SCK3n SO/TxD SI3n SI/RxD SO3n CLK X1Note 5 GND VSS0, VSS1, AVSS, AVREF (b) 3-wire serial I/O (SIO30) with handshakeNote 2 Dedicated flash programmer Flash memory version VPP VPP VDD VDD0Note 4, VDD1Note 4, AVDD /RESET RESET SCK SCK30 SO/TxD SI3 SI/RxD SO3 H/S P25 (HS) CLK X1Note 5 GND VSS0, VSS1, AVSS, AVREF (c) I2C bus (IIC0)Note 3 Dedicated flash programmer Flash memory version VPP VPP VDD VDD0Note 4, VDD1Note 4, AVDD /RESET RESET SCK SCL0 SI/RxD SDA0 CLK X1Note 5 GND VSS0, VSS1, AVSS, AVREF Notes 1. n = 0, 1: PD78F0034A, 78F0034B n = 0: PD78F0034AY, 78F0034BY 2. PD78F0034B, 78F0034BY only 3. PD78F0034AY, 78F0034BY only 4. Even if power is supplied on board, the VDD0 and VDD1 pins must be connected to VDD of the dedicated flash programmer. Supply the VDD voltage before programming is started. 5. The X1 pin can be supplied on board. In this case, the pin does not need to be connected to the dedicated flash programmer. 452 User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-4. Example of Connection with Dedicated Flash Programmer (2/2) (d) UART (UART0) Dedicated flash programmer Flash memory version VPP VPP VDD VDD0Note 1, VDD1Note 1, AVDD /RESET RESET SO/TXD RXD0 SI/RXD TXD0 CLK X1Note 2 GND VSS0, VSS1, AVSS, AVREF (e) Pseudo 3-wire serial I/O Dedicated flash programmer Flash memory version VPP VPP VDD VDD0Note 1, VDD1Note 1, AVDD /RESET RESET SCK P72 SO/TxD P70 SI/RxD P71 CLK X1Note 2 GND VSS0, VSS1, AVSS, AVREF Notes 1. Even if power is supplied on board, the VDD0 and VDD1 pins must be connected to VDD of the dedicated flash programmer. Supply the VDD voltage before programming is started. 2. The X1 pin can be supplied on board. In this case, the pin does not need to be connected to the dedicated flash programmer. If Flashpro III/Flashpro IV is used as the dedicated flash programmer, the following signals are generated for the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY. For details, refer to the manual of Flashpro III/Flashpro IV. User's Manual U14046EJ5V0UD 453 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Table 23-9. Pin Connection List Signal Name I/O Pin Function Pin Name SIO30 SIO31 SIO30 UART0 IIC0 Pseudo (HS) Note 1 Note 3 3-wire Note 2 VPP Output Write voltage VDD I/O VDD voltage generation/voltage VDD0, VDD1, AVDD monitoring - GND VPP Ground VSS0, VSS1, AVSS, AVREF CLK Output Clock output X1 /RESET Output Reset signal RESET SI/RXD Input Reception signal SO30/SO31Note 1 TxD0/SDA0Note 3/P71 SO/TXD Output Transmission signal SI30/SI31Note 1/RxD0/ P70 SCK Output Transfer clock SCK30/SCK31Note 1/ Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 x x SCL0Note 3/P72 H/S Input P25 (HS)Note 2 Handshake signal x x x Notes 1. PD78F0034A, 78F0034B only 2. PD78F0034B, 78F0034BY only 3. PD78F0034AY, 78F0034BY only 4. VDD voltage must be supplied before programming is started. Remark : Pin must be connected. : If the signal is supplied on the target board, pin does not need to be connected. x : Pin does not need to be connected. 454 User's Manual U14046EJ5V0UD x x CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.5.3 On-board pin processing When performing programming on the target system, provide a connector on the target system to connect the dedicated flash programmer. An on-board function that allows switching between normal operation mode and flash memory programming mode may be required in some cases. <VPP pin> In normal operation mode, input 0 V to the VPP pin. In flash memory programming mode, a write voltage of 10.0 V (TYP.) is supplied to the VPP pin, so perform the following. (1) Connect a pull-down resistor (RVPP = 10 k) to the VPP pin. (2) Use the jumper on the board to switch the VPP pin input to either the programmer or directly to GND. A VPP pin connection example is shown below. Figure 23-5. VPP Pin Connection Example PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Connection pin of dedicated flash programmer VPP Pull-down resistor (RVPP) <Serial interface pin> The following shows the pins used by the serial interface. Serial Interface Pins Used 3-wire serial I/O (SIO30) 3-wire serial I/O (SIO31)Note 1 SI30/P20, SO30/P21, SCK30/P22 SI31/P34, SO31/P35, SCK31/P36 3-wire serial I/O (SIO30) with handshakeNote 2 SI30/P20, SO30/P21, SCK30/P22, HS/P25 I2C bus (IIC0)Note 3 SDA0/P32, SCL0/P33 UART (UART0) RXD0/P23, TXD0/P24 Pseudo 3-wire serial I/O P70/TI00/TO0 (serial data input), P71/TI01 (serial data output), P72/TI50/TO50 (serial clock input) Notes 1. PD78F0034A, 78F0034B only 2. PD78F0034B, 78F0034BY only 3. PD78F0034AY, 78F0034BY only When connecting the dedicated flash programmer to a serial interface pin that is connected to another device on-board, signal conflict or abnormal operation of the other device may occur. Care must therefore be taken with such connections. User's Manual U14046EJ5V0UD 455 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY (1) Signal conflict If the dedicated flash programmer (output) is connected to a serial interface pin (input) that is connected to another device (output), a signal conflict occurs. To prevent this, isolate the connection with the other device or set the other device to the output high impedance status. Figure 23-6. Signal Conflict (Input Pin of Serial Interface) Flash memory version Signal conflict Connection pin of dedicated flash programmer Input pin Other device Output pin In the flash memory programming mode, the signal output by another device and the signal sent by the dedicated flash programmer conflict, therefore, isolate the signal of the other device. (2) Abnormal operation of other device If the dedicated flash programmer (output or input) is connected to a serial interface pin (input or output) that is connected to another device (input), a signal is output to the device, which may cause an abnormal operation. To prevent this abnormal operation, isolate the connection with the other device or set so that the input signals to the other device are ignored. Figure 23-7. Abnormal Operation of Other Device Flash memory version Connection pin of dedicated flash programmer Pin Other device Input pin If the signal output by the PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY affects another device in the flash memory programming mode, isolate the signals of the other device. Flash memory version Connection pin of dedicated flash programmer Pin Other device Input pin If the signal output by the dedicated flash programmer affects another device in the flash memory programming mode, isolate the signals of the other device. 456 User's Manual U14046EJ5V0UD PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY CHAPTER 23 <RESET pin> If the reset signal of the dedicated flash programmer is connected to the RESET pin connected to the reset signal generator on-board, a signal conflict occurs. To prevent this, isolate the connection with the reset signal generator. If the reset signal is input from the user system in the flash memory programming mode, a normal programming operation cannot be performed. Therefore, do not input reset signals from other than the dedicated flash programmer. Figure 23-8. Signal Conflict (RESET Pin) Flash memory version Signal conflict Connection pin of dedicated flash programmer RESET Reset signal generator Output pin The signal output by the reset signal generator and the signal output from the dedicated flash programmer conflict in the flash memory programming mode, so isolate the signal of the reset signal generator. <Port pins> When the PD78F0034A, 78F0034B, 78F0034AY, and 78F0034BY enter the flash memory programming mode, all the pins other than those that communicate in flash memory programming are in the same status as immediately after reset. If the external device does not recognize initial statuses such as the output high impedance status, therefore, connect the external device to VDD0 or VSS0 via a resistor. <Oscillator> When using the on-board clock, connect X1, X2, XT1, and XT2 as required in the normal operation mode. When using the clock output of the flash programmer, connect it directly to X1, disconnecting the main oscillator on-board, and leave the X2 pin open. The subsystem clock conforms to the normal operation mode. <Power supply> To use the power output from the flash programmer, connect the VDD0 and VDD1 pins to VDD of the flash programmer, and the VSS0 and VSS1 pins to GND of the flash programmer. To use the on-board power supply, make connections that accord with the normal operation mode. However, because the voltage is monitored by the flash programmer, be sure to connect the VDD0, VDD1, VSS0, and VSS1 pins to VDD and GND of the flash programmer. Supply the same power as in the normal operation mode to the other power supply pins (AVDD, AVREF, and AVSS). User's Manual U14046EJ5V0UD 457 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 23.5.4 Connection on adapter for flash memory writing Examples of the recommended connection when using the adapter for flash memory writing are shown below. Figure 23-9. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO30) Mode (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP2) WRITER INTERFACE 458 SI SO SCK CLKOUT RESET PP RESERVE/HS User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-9. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO30) Mode (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 459 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-10. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO31) Mode (PD78F0034A, 78F0034B only) (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP) WRITER INTERFACE 460 SI SO SCK CLKOUT RESET VPP RESERVE/HS User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-10. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO31) Mode (PD78F0034A, 78F0034B only) (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 461 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-11. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO30 + HS) Mode (PD78F0034B, 78F0034BY only) (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP2) WRITER INTERFACE 462 SI SO SCK CLKOUT RESET VPP RESERVE/HS User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-11. Example of Wiring Adapter for Flash Memory Writing in 3-Wire Serial I/O (SIO30 + HS) Mode (PD78F0034B, 78F0034BY only) (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 463 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-12. Example of Wiring Adapter for Flash Memory Writing in I2C Bus (IIC0) Mode (PD78F0034AY, 78F0034BY only) (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP2) WRITER INTERFACE 464 SI SO SCK CLKOUT RESET VPP RESERVE/HS User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-12. Example of Wiring Adapter for Flash Memory Writing in I2C Bus (IIC0) Mode (PD78F0034AY, 78F0034BY only) (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 465 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-13. Example of Wiring Adapter for Flash Memory Writing in UART (UART0) Mode (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP2) WRITER INTERFACE 466 SI SO SCK CLKOUT RESET VPP RESERVE/HS User's Manual U14046EJ5V0UD CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-13. Example of Wiring Adapter for Flash Memory Writing in UART (UART0) Mode (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 467 CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Figure 23-14. Example of Wiring Adapter for Flash Memory Writing in Pseudo 3-Wire Serial I/O Mode (1/2) (1) 64-pin plastic SDIP (19.05 mm (750)) VDD (2.7 to 5.5 V) GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 GND VDD LVDD (VPP2) WRITER INTERFACE 468 SI SO SCK CLKOUT RESET VPP RESERVE/HS User's Manual U14046EJ5V0UD PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY CHAPTER 23 Figure 23-14. Example of Wiring Adapter for Flash Memory Writing in Pseudo 3-Wire Serial I/O Mode (2/2) (2) 64-pin plastic QFP (14 x 14), 64-pin plastic LQFP (14 x 14), 64-pin plastic TQFP (12 x 12), 64-pin plastic LQFP (10 x 10) VDD (2.7 to 5.5 V) GND LVDD (VPP2) VDD GND 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 SI SO SCK CLKOUT RESET VPP RESERVE/HS WRITER INTERFACE User's Manual U14046EJ5V0UD 469 CHAPTER 24 INSTRUCTION SET This chapter lists each instruction set of the PD780024A, 780034A, 780024AY, 780034AY Subseries in table form. For details of its operation and operation code, refer to the separate document 78K/0 Series Instructions User's Manual (U12326E). 470 User's Manual U14046EJ5V0UD CHAPTER 24 INSTRUCTION SET 24.1 Conventions 24.1.1 Operand identifiers and specification methods Operands are written in "Operand" column of each instruction in accordance with the specification method of the instruction operand identifier (refer to the assembler specifications for detail). When there are two or more methods, select one of them. Alphabetic letters in capitals and symbols, #, !, $, and [ ] are key words and must be written as they are. Each symbol has the following meaning. * #: Immediate data specification * !: Absolute address specification * $: Relative address specification * [ ]: Indirect address specification In the case of immediate data, describe an appropriate numeric value or a label. When using a label, be sure to write the #, !, $, and [ ] symbols. For operand register identifiers, r and rp, either function names (X, A, C, etc.) or absolute names (names in parentheses in the table below, R0, R1, R2, etc.) can be used for specification. Table 24-1. Operand Identifiers and Specification Methods Identifier Specification Method r rp sfr sfrp X (R0), A (R1), C (R2), B (R3), E (R4), D (R5), L (R6), H (R7) AX (RP0), BC (RP1), DE (RP2), HL (RP3) Special function register symbolNote Special function register symbol (16-bit manipulatable register even addresses only)Note saddr saddrp FE20H to FF1FH Immediate data or labels FE20H to FF1FH Immediate data or labels (even address only) addr16 addr11 addr5 0000H to FFFFH Immediate data or labels (only even addresses for 16-bit data transfer instructions) 0800H to 0FFFH Immediate data or labels 0040H to 007FH Immediate data or labels (even address only) word byte bit 16-bit immediate data or label 8-bit immediate data or label 3-bit immediate data or label RBn RB0 to RB3 Note Addresses from FFD0H to FFDFH cannot be accessed with these operands. Remark For special function register symbols, see Table 5-5 Special Function Register List. User's Manual U14046EJ5V0UD 471 CHAPTER 24 INSTRUCTION SET 24.1.2 Description of "operation" column A: A register; 8-bit accumulator X: X register B: B register C: C register D: D register E: E register H: H register L: L register AX: AX register pair; 16-bit accumulator BC: BC register pair DE: DE register pair HL: HL register pair PC: Program counter SP: Stack pointer PSW: Program status word CY: Carry flag AC: Auxiliary carry flag Z: Zero flag RBS: Register bank select flag IE: Interrupt request enable flag ( ): Memory contents indicated by address or register contents in parentheses XH, XL: Higher 8 bits and lower 8 bits of 16-bit register : Logical product (AND) : Logical sum (OR) : Exclusive logical sum (exclusive OR) : Inverted data addr16: 16-bit immediate data or label jdisp8: Signed 8-bit data (displacement value) 24.1.3 Description of "flag operation" column (Blank): Not affected 0: Cleared to 0 1: Set to 1 x: Set/cleared according to the result R: Previously saved value is restored 472 User's Manual U14046EJ5V0UD CHAPTER 24 INSTRUCTION SET 24.2 Operation List Instruction Group Mnemonic 8-bit data transfer MOV Operands Byte Note 1 Note 2 Operation 2 4 - r byte saddr, #byte 3 6 7 (saddr) byte sfr, #byte 3 - 7 sfr byte A, r Note 3 1 2 - Ar r, A Note 3 1 2 - rA A, saddr 2 4 5 A (saddr) saddr, A 2 4 5 (saddr) A A, sfr 2 - 5 A sfr sfr, A 2 - 5 sfr A A, !addr16 3 8 9+n A (addr16) !addr16, A 3 8 9+m (addr16) A PSW, #byte 3 - 7 PSW byte A, PSW 2 - 5 A PSW PSW, A 2 - 5 PSW A A, [DE] 1 4 5+n A (DE) [DE], A 1 4 5+m (DE) A A, [HL] 1 4 5+n A (HL) [HL], A 1 4 5+m (HL) A A, [HL + byte] 2 8 9+n A (HL + byte) [HL + byte], A 2 8 9+m (HL + byte) A A, [HL + B] 1 6 7+n A (HL + B) [HL + B], A 1 6 7+m (HL + B) A A, [HL + C] 1 6 7+n A (HL + C) 1 6 7+m (HL + C) A 1 2 - Ar A, r Note 3 Flag Z AC CY r, #byte [HL + C], A XCH Clock A, saddr 2 4 6 A (saddr) A, sfr 2 - 6 A (sfr) A, !addr16 3 8 10 + n + m A (addr16) A, [DE] 1 4 6+n+m A (DE) A, [HL] 1 4 6+n+m A (HL) A, [HL + byte] 2 8 10 + n + m A (HL + byte) A, [HL + B] 2 8 10 + n + m A (HL + B) A, [HL + C] 2 8 10 + n + m A (HL + C) x x x x x x Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed 3. Except r = A Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 4. m is the number of waits when external memory expansion area is written to. User's Manual U14046EJ5V0UD 473 CHAPTER 24 Instruction Group Mnemonic 16-bit data transfer MOVW Operands Byte Note 2 Operation Flag Z AC CY 3 6 - rp word saddrp, #word 4 8 10 (saddrp) word sfrp, #word 4 - 10 sfrp word AX, saddrp 2 6 8 AX (saddrp) saddrp, AX 2 6 8 (saddrp) AX AX, sfrp 2 - 8 AX sfrp 2 - 8 sfrp AX AX, rp Note 3 1 4 - AX rp rp, AX Note 3 1 4 - rp AX 3 10 12 + 2n AX (addr16) 3 10 12 + 2m (addr16) AX 1 4 - AX rp 2 4 - A, CY A + byte x x x 3 6 8 (saddr), CY (saddr) + byte x x x AX, !addr16 !addr16, AX XCHW AX, rp ADD A, #byte Note 3 saddr, #byte 2 4 - A, CY A + r x x x r, A 2 4 - r, CY r + A x x x A, saddr 2 4 5 A, CY A + (saddr) x x x A, !addr16 3 8 9+n A, CY A + (addr16) x x x A, r ADDC Clock Note 1 rp, #word sfrp, AX 8-bit operation INSTRUCTION SET Note 4 A, [HL] 1 4 5+n A, CY A + (HL) x x x A, [HL + byte] 2 8 9+n A, CY A + (HL + byte) x x x A, [HL + B] 2 8 9+n A, CY A + (HL + B) x x x A, [HL + C] 2 8 9+n A, CY A + (HL + C) x x x A, #byte 2 4 - A, CY A + byte + CY x x x saddr, #byte 3 6 8 (saddr), CY (saddr) + byte + CY x x x 2 4 - A, CY A + r + CY x x x 2 4 - r, CY r + A + CY x x x A, r Note 4 r, A A, saddr 2 4 5 A, CY A + (saddr) + CY x x x A, !addr16 3 8 9+n A, CY A + (addr16) + CY x x x A, [HL] 1 4 5+n A, CY A + (HL) + CY x x x A, [HL + byte] 2 8 9+n A, CY A + (HL + byte) + CY x x x A, [HL + B] 2 8 9+n A, CY A + (HL + B) + CY x x x A, [HL + C] 2 8 9+n A, CY A + (HL + C) + CY x x x Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed 3. Only when rp = BC, DE or HL 4. Except r = A Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 4. m is the number of waits when external memory expansion area is written to. 474 User's Manual U14046EJ5V0UD CHAPTER 24 Instruction Group Mnemonic 8-bit operation SUB Operands Byte A, #byte saddr, #byte Operation Flag Z AC CY Note 2 2 4 - A, CY A - byte x x x 3 6 8 (saddr), CY (saddr) - byte x x x 2 4 - A, CY A - r x x x 2 4 - r, CY r - A x x x A, saddr 2 4 5 A, CY A - (saddr) x x x A, !addr16 3 8 9+n A, CY A - (addr16) x x x Note 3 A, [HL] 1 4 5+n A, CY A - (HL) x x x A, [HL + byte] 2 8 9+n A, CY A - (HL + byte) x x x A, [HL + B] 2 8 9+n A, CY A - (HL + B) x x x A, [HL + C] 2 8 9+n A, CY A - (HL + C) x x x A, #byte 2 4 - A, CY A - byte - CY x x x saddr, #byte 3 6 8 (saddr), CY (saddr) - byte - CY x x x 2 4 - A, CY A - r - CY x x x 2 4 - r, CY r - A - CY x x x A, r Note 3 r, A AND Clock Note 1 r, A A, r SUBC INSTRUCTION SET A, saddr 2 4 5 A, CY A - (saddr) - CY x x x A, !addr16 3 8 9+n A, CY A - (addr16) - CY x x x A, [HL] 1 4 5+n A, CY A - (HL) - CY x x x A, [HL + byte] 2 8 9+n A, CY A - (HL + byte) - CY x x x A, [HL + B] 2 8 9+n A, CY A - (HL + B) - CY x x x A, [HL + C] 2 8 9+n A, CY A - (HL + C) - CY x x x A, #byte 2 4 - AA x 3 6 8 (saddr) (saddr) saddr, #byte byte byte x 2 4 - AA r, A 2 4 - rr A, saddr 2 4 5 AA (saddr) x A, !addr16 3 8 9+n AA (addr16) x A, [HL] 1 4 5+n AA (HL) x A, [HL + byte] 2 8 9+n AA (HL + byte) x A, [HL + B] 2 8 9+n AA (HL + B) x A, [HL + C] 2 8 9+n AA (HL + C) x A, r Note 3 r x x A Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed 3. Except r = A Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. User's Manual U14046EJ5V0UD 475 CHAPTER 24 Instruction Group Mnemonic 8-bit operation OR Operands Byte A, #byte saddr, #byte Operation Flag Z AC CY Note 2 2 4 - A A byte x 3 6 8 (saddr) (saddr) byte x 2 4 - AA r x 2 4 - rr A x A, saddr 2 4 5 A A (saddr) x A, !addr16 3 8 9+n A A (addr16) x A, [HL] 1 4 5+n A A (HL) x A, [HL + byte] 2 8 9+n A A (HL + byte) x A, [HL + B] 2 8 9+n A A (HL + B) x A, [HL + C] 2 8 9+n A A (HL + C) x A, #byte 2 4 - AA saddr, #byte 3 6 8 (saddr) (saddr) 2 4 - AA r, A 2 4 - rr A, saddr 2 4 5 AA (saddr) x A, !addr16 3 8 9+n AA (addr16) x A, [HL] 1 4 5+n AA (HL) x A, [HL + byte] 2 8 9+n AA (HL + byte) x A, r CMP Clock Note 1 r, A A, r XOR INSTRUCTION SET Note 3 Note 3 x byte byte r x x x A A, [HL + B] 2 8 9+n AA (HL + B) x A, [HL + C] 2 8 9+n AA (HL + C) x A, #byte 2 4 - A - byte x x x 3 6 8 (saddr) - byte x x x saddr, #byte 2 4 - A-r x x x r, A 2 4 - r-A x x x A, saddr 2 4 5 A - (saddr) x x x A, !addr16 3 8 9+n A - (addr16) x x x A, r Note 3 A, [HL] 1 4 5+n A - (HL) x x x A, [HL + byte] 2 8 9+n A - (HL + byte) x x x A, [HL + B] 2 8 9+n A - (HL + B) x x x A, [HL + C] 2 8 9+n A - (HL + C) x x x Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed 3. Except r = A Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 476 User's Manual U14046EJ5V0UD CHAPTER 24 Instruction Group Mnemonic 16-bit operation ADDW AX, #word SUBW Multiply/ divide Byte Clock Operation Flag Z AC CY Note 1 Note 2 3 6 - AX, CY AX + word x x x AX, #word 3 6 - AX, CY AX - word x x x CMPW AX, #word 3 6 - AX - word x x x MULU X 2 16 - AX A x X DIVUW C 2 25 - AX (Quotient), C (Remainder) AX / C r 1 2 - rr+1 x x saddr 2 4 6 (saddr) (saddr) + 1 x x r 1 2 - rr-1 x x saddr 2 4 6 (saddr) (saddr) - 1 x x INCW rp 1 4 - rp rp + 1 DECW rp 1 4 - rp rp - 1 ROR A, 1 1 2 - (CY, A7 A0, Am - 1 Am) x 1 time x ROL A, 1 1 2 - (CY, A0 A7, Am + 1 Am) x 1 time x RORC A, 1 1 2 - (CY A0, A7 CY, Am - 1 Am) x 1 time x ROLC A, 1 1 2 - (CY A7, A0 CY, A m + 1 Am) x 1 time x ROR4 [HL] 2 10 Increment/ INC decrement DEC Rotate Operands INSTRUCTION SET 12 + n + m A3 - 0 (HL)3 - 0, (HL)7 - 4 A3 - 0, (HL)3 - 0 (HL)7 - 4 ROL4 [HL] 12 + n + m A3 - 0 (HL)7 - 4, (HL)3 - 0 A3 - 0, 2 10 ADJBA 2 4 - Decimal Adjust Accumulator after Addition x x x ADJBS 2 4 - Decimal Adjust Accumulator after Subtract x x x CY, saddr.bit 3 6 7 CY (saddr.bit) x CY, sfr.bit 3 - 7 CY sfr.bit x CY, A.bit 2 4 - CY A.bit x CY, PSW.bit 3 - 7 CY PSW.bit x CY, [HL].bit 2 6 7+n CY (HL).bit x saddr.bit, CY 3 6 8 (saddr.bit) CY sfr.bit, CY 3 - 8 sfr.bit CY A.bit, CY 2 4 - A.bit CY PSW.bit, CY 3 - 8 PSW.bit CY [HL].bit, CY 2 6 8+n+m (HL).bit CY (HL)7 - 4 (HL)3 - 0 BCD adjust Bit manipulate MOV1 x x Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 4. m is the number of waits when external memory expansion area is written to. User's Manual U14046EJ5V0UD 477 CHAPTER 24 Instruction Group Mnemonic Bit manipulate AND1 OR1 XOR1 SET1 CLR1 SET1 Operands Byte INSTRUCTION SET Clock Note 1 Note 2 Operation Flag Z AC CY CY, saddr.bit 3 6 7 CY CY (saddr.bit) x CY, sfr.bit 3 - 7 CY CY sfr.bit x CY, A.bit 2 4 - CY CY A.bit x CY, PSW.bit 3 - 7 CY CY PSW.bit x CY, [HL].bit 2 6 7+n CY CY (HL).bit x CY, saddr.bit 3 6 7 CY CY (saddr.bit) x CY, sfr.bit 3 - 7 CY CY sfr.bit x CY, A.bit 2 4 - CY CY A.bit x CY, PSW.bit 3 - 7 CY CY PSW.bit x CY, [HL].bit 2 6 7+n CY CY (HL).bit x CY, saddr.bit 3 6 7 CY CY (saddr.bit) x CY, sfr.bit 3 - 7 CY CY sfr.bit x CY, A.bit 2 4 - CY CY A.bit x CY, PSW.bit 3 - 7 CY CY PSW.bit x CY CY (HL).bit x CY, [HL].bit 2 6 7+n saddr.bit 2 4 6 (saddr.bit) 1 sfr.bit 3 - 8 sfr.bit 1 A.bit 2 4 - A.bit 1 6 PSW.bit 1 x x x x x x PSW.bit 2 - [HL].bit 2 6 saddr.bit 2 4 6 (saddr.bit) 0 sfr.bit 3 - 8 sfr.bit 0 A.bit 2 4 - A.bit 0 PSW.bit 2 - 6 PSW.bit 0 [HL].bit 2 6 CY 1 2 - CY 1 1 8 + n + m (HL).bit 1 8 + n + m (HL).bit 0 CLR1 CY 1 2 - CY 0 0 NOT1 CY 1 2 - CY CY x Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 4. m is the number of waits when external memory expansion area is written to. 478 User's Manual U14046EJ5V0UD CHAPTER 24 Instruction Group Mnemonic Clock Note 1 Note 2 Operation Flag Z AC CY 3 7 - (SP - 1) (PC + 3)H, (SP - 2) (PC + 3)L, PC addr16, SP SP - 2 CALLF !addr11 2 5 - (SP - 1) (PC + 2)H, (SP - 2) (PC + 2)L, PC15 - 11 00001, PC10 - 0 addr11, SP SP - 2 CALLT [addr5] 1 6 - (SP - 1) (PC + 1)H, (SP - 2) (PC + 1)L, PCH (00000000, addr5 + 1), PCL (00000000, addr5), SP SP - 2 BRK 1 6 - (SP - 1) PSW, (SP - 2) (PC + 1)H, (SP - 3) (PC + 1)L, PCH (003FH), PCL (003EH), SP SP - 3, IE 0 RET 1 6 - PCH (SP + 1), PCL (SP), SP SP + 2 RETI 1 6 - PCH (SP + 1), PCL (SP), PSW (SP + 2), SP SP + 3 R R R RETB 1 6 - PCH (SP + 1), PCL (SP), PSW (SP + 2), SP SP + 3 R R R PSW 1 2 - (SP - 1) PSW, SP SP - 1 rp 1 4 - (SP - 1) rpH, (SP - 2) rpL, SP SP - 2 PSW 1 2 - PSW (SP), SP SP + 1 R R R rp 1 4 - rpH (SP + 1), rpL (SP), SP SP + 2 SP, #word 4 - 10 SP word SP, AX 2 - 8 SP AX PUSH POP MOVW Unconditional branch Byte !addr16 Call/return CALL Stack manipulate Operands INSTRUCTION SET AX, SP 2 - 8 AX SP !addr16 3 6 - PC addr16 $addr16 2 6 - PC PC + 2 + jdisp8 AX 2 8 - PCH A, PCL X $addr16 2 6 - PC PC + 2 + jdisp8 if CY = 1 $addr16 2 6 - PC PC + 2 + jdisp8 if CY = 0 BZ $addr16 2 6 - PC PC + 2 + jdisp8 if Z = 1 BNZ $addr16 2 6 - PC PC + 2 + jdisp8 if Z = 0 BR Conditional BC branch BNC Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. User's Manual U14046EJ5V0UD 479 CHAPTER 24 Instruction Group Mnemonic Conditional branch BT BF BTCLR Operands Byte INSTRUCTION SET Clock Note 1 Note 2 Operation Flag Z AC CY saddr.bit, $addr16 3 8 9 PC PC + 3 + jdisp8 if (saddr.bit) = 1 sfr.bit, $addr16 4 - 11 PC PC + 4 + jdisp8 if sfr.bit = 1 A.bit, $addr16 3 8 - PC PC + 3 + jdisp8 if A.bit = 1 PSW.bit, $addr16 3 - 9 PC PC + 3 + jdisp8 if PSW.bit = 1 [HL].bit, $addr16 3 10 11 + n PC PC + 3 + jdisp8 if (HL).bit = 1 saddr.bit, $addr16 4 10 11 sfr.bit, $addr16 4 - 11 PC PC + 4 + jdisp8 if sfr.bit = 0 A.bit, $addr16 3 8 - PC PC + 3 + jdisp8 if A.bit = 0 PSW.bit, $addr16 4 - 11 PC PC + 4 + jdisp8 if PSW.bit = 0 [HL].bit, $addr16 3 10 11 + n PC PC + 3 + jdisp8 if (HL).bit = 0 saddr.bit, $addr16 4 10 12 PC PC + 4 + jdisp8 if (saddr.bit) = 1 then reset (saddr.bit) sfr.bit, $addr16 4 - 12 PC PC + 4 + jdisp8 if sfr.bit = 1 then reset sfr.bit A.bit, $addr16 3 8 - PC PC + 3 + jdisp8 if A.bit = 1 then reset A.bit PSW.bit, $addr16 4 - 12 PC PC + 4 + jdisp8 if PSW.bit = 1 then reset PSW.bit [HL].bit, $addr16 3 10 PC PC + 4 + jdisp8 if (saddr.bit) = 0 x x x 12 + n + m PC PC + 3 + jdisp8 if (HL).bit = 1 then reset (HL).bit DBNZ CPU control B, $addr16 2 6 - B B - 1, then PC PC + 2 + jdisp8 if B 0 C, $addr16 2 6 - C C -1, then PC PC + 2 + jdisp8 if C 0 saddr, $addr16 3 8 10 (saddr) (saddr) - 1, then PC PC + 3 + jdisp8 if(saddr) 0 RBn 2 4 - RBS1, 0 n NOP 1 2 - No Operation EI 2 - 6 IE 1 (Enable Interrupt) DI 2 - 6 IE 0 (Disable Interrupt) HALT 2 6 - Set HALT Mode STOP 2 6 - Set STOP Mode SEL Notes 1. When the internal high-speed RAM area is accessed or instruction with no data access 2. When an area except the internal high-speed RAM area is accessed Remarks 1. One instruction clock cycle is one cycle of the CPU clock (fCPU) selected by the processor clock control register (PCC). 2. This clock cycle applies to internal ROM program. 3. n is the number of waits when external memory expansion area is read from. 4. m is the number of waits when external memory expansion area is written to. 480 User's Manual U14046EJ5V0UD CHAPTER 24 INSTRUCTION SET 24.3 Instructions Listed by Addressing Type (1) 8-bit instructions MOV, XCH, ADD, ADDC, SUB, SUBC, AND, OR, XOR, CMP, MULU, DIVUW, INC, DEC, ROR, ROL, RORC, ROLC, ROR4, ROL4, PUSH, POP, DBNZ User's Manual U14046EJ5V0UD 481 CHAPTER 24 Second Operand #byte A rNote sfr INSTRUCTION SET saddr !addr16 PSW [DE] [HL] First Operand A ADD ADDC SUB SUBC AND OR XOR CMP r MOV MOV MOV XCH XCH ADD ADDC SUB SUBC AND OR XOR CMP MOV XCH ADD ADDC SUB SUBC AND OR XOR CMP MOV MOV XCH ADD ADDC SUB SUBC AND OR XOR CMP MOV XCH MOV XCH ADD ADDC SUB SUBC AND OR XOR CMP [HL + byte] $addr16 [HL + B] [HL + C] MOV XCH ADD ADDC SUB SUBC AND OR XOR CMP 1 None ROR ROL RORC ROLC MOV ADD ADDC SUB SUBC AND OR XOR INC DEC CMP B, C DBNZ sfr MOV MOV saddr MOV MOV ADD ADDC SUB SUBC AND OR XOR DBNZ INC DEC CMP !addr16 PSW MOV MOV MOV [DE] MOV [HL] MOV [HL + byte] [HL + B] [HL + C] MOV PUSH POP ROR4 ROL4 X MULU C DIVUW Note Except r = A 482 User's Manual U14046EJ5V0UD CHAPTER 24 INSTRUCTION SET (2) 16-bit instructions MOVW, XCHW, ADDW, SUBW, CMPW, PUSH, POP, INCW, DECW Second Operand #word AX rpNote sfrp saddrp !addr16 SP None First Operand AX ADDW SUBW MOVW XCHW MOVW MOVW MOVW MOVW CMPW rp MOVW MOVWNote sfrp MOVW MOVW saddrp MOVW MOVW !addr16 SP INCW DECW PUSH POP MOVW MOVW MOVW Note Only when rp = BC, DE, HL (3) Bit manipulation instructions MOV1, AND1, OR1, XOR1, SET1, CLR1, NOT1, BT, BF, BTCLR Second Operand A.bit sfr.bit saddr.bit PSW.bit [HL].bit CY $addr16 None First Operand A.bit MOV1 BT BF BTCLR SET1 CLR1 sfr.bit MOV1 BT BF BTCLR SET1 CLR1 saddr.bit MOV1 BT BF BTCLR SET1 CLR1 PSW.bit MOV1 BT BF BTCLR SET1 CLR1 [HL].bit MOV1 BT BF BTCLR SET1 CLR1 CY MOV1 AND1 OR1 XOR1 MOV1 AND1 OR1 XOR1 MOV1 AND1 OR1 XOR1 MOV1 AND1 OR1 XOR1 MOV1 AND1 OR1 XOR1 User's Manual U14046EJ5V0UD SET1 CLR1 NOT1 483 CHAPTER 24 INSTRUCTION SET (4) Call instructions/branch instructions CALL, CALLF, CALLT, BR, BC, BNC, BZ, BNZ, BT, BF, BTCLR, DBNZ Second Operand AX !addr16 !addr11 [addr5] $addr16 First Operand Basic instruction BR CALL BR CALLF CALLT BR BC BNC BZ BNZ Compound instruction BT BF BTCLR DBNZ (5) Other instructions ADJBA, ADJBS, BRK, RET, RETI, RETB, SEL, NOP, EI, DI, HALT, STOP 484 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Target products * PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A, 780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), 780034A(A) for which orders were received after December 1, 2001 (Products with a rankNote other than K, E, P, X) * PD78F0034B, 78F0034B(A) Note The rank is indicated by the 5th digit from the left in the lot number marked on the package. Lot number x x x x Year Week code code Rank User's Manual U14046EJ5V0UD 485 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Absolute Maximum Ratings (TA = 25C) Parameter Supply voltage Symbol Ratings Unit -0.3 to +6.5 V -0.3 to +10.5 V AVDD -0.3 to VDD + 0.3Note 1 V AVREF -0.3 to VDD + 0.3Note 1 V AVSS -0.3 to +0.3 V -0.3 to VDD + 0.3Note 1 V -0.3 to +6.5 V -0.3 to VDD + 0.3Note 1 V -0.3 to VDD + 0.3Note 1 V AVSS - 0.3 to AVREF + 0.3Note 1 V VDD VPP Input voltage Conditions Flash memory version only, Note 2 VI1 P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, X1, X2, XT1, XT2, RESET VI2 P30 to P33 N-ch open drain On-chip pull-up resistor Output voltage VO Analog input voltage VAN P10 to P17 Analog input pin and -0.3 to VDD + 0.3Note 1 Output current, high Output current, low Operating ambient IOH IOL TA temperature Storage Tstg temperature Per pin -10 mA Total for P00 to P03, P40 to P47, P50 to P57, P64 to P67, P70 to P75 -15 mA Total for P20 to P25, P30 to P36 -15 mA Per pin for P00 to P03, P20 to P25, P34 to P36, P40 to P47, P64 to P67, P70 to P75 20 mA Per pin for P30 to P33, P50 to P57 30 mA Total for P00 to P03, P40 to P47, P64 to P67, P70 to P75 50 mA Total for P20 to P25 20 mA Total for P30 to P36 100 mA Total for P50 to P57 100 mA During normal operation -40 to +85 C During flash memory programming +10 to +80 C Mask ROM version -65 to +150 C Flash memory version -40 to +125 C Notes 1. 6.5 V or below (Note 2 is explained on the following page.) Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. 486 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Notes 2. Make sure that the following conditions of the VPP voltage application timing are satisfied when the flash memory is written. * When supply voltage rises VPP must exceed VDD 10 s or more after VDD has reached the lower-limit value (1.8 V) of the operating voltage range (see a in the figure below). * When supply voltage drops VDD must be lowered 10 s or more after VPP falls below the lower-limit value (1.8 V) of the operating voltage range of VDD (see b in the figure below). VDD 1.8 V 0V a b VPP 1.8 V 0V Capacitance (TA = 25C, VDD = VSS = 0 V) Parameter Symbol Conditions MIN. TYP. MAX. Unit Input capacitance CIN f = 1 MHz Unmeasured pins returned to 0 V. 15 pF I/O capacitance CIO f = 1 MHz Unmeasured pins returned to 0 V. P00 to P03, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75 15 pF P30 to P33 20 pF Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. User's Manual U14046EJ5V0UD 487 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Main System Clock Oscillator Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Resonator Ceramic resonator Recommended Circuit X2 X1 VSS1 Parameter Oscillation frequency (fX)Note 1 R1 C2 Oscillation C1 stabilization timeNote 2 Crystal resonator X2 X1 VSS1 Oscillation frequency (fX)Note 1 R1 C2 External clock X2 C1 X1 Conditions MIN. TYP. MAX. Unit MHz 4.5 V VDD 5.5 V 1.0 12.0 3.0 V VDD < 4.5 V 1.0 8.38 1.8 V VDD < 3.0 V 1.0 5.0 After VDD reaches oscillation voltage range MIN. 4 ms MHz 4.5 V VDD 5.5 V 1.0 12.0 3.0 V VDD < 4.5 V 1.0 8.38 1.8 V VDD < 3.0 V 1.0 5.0 Oscillation 4.0 V VDD 5.5 V 10 stabilization timeNote 2 1.8 V VDD < 4.0 V 30 X1 input frequency (fX)Note 1 4.5 V VDD 5.5 V 1.0 12.0 3.0 V VDD < 4.5 V 1.0 8.38 1.8 V VDD < 3.0 V 1.0 5.0 X1 input 4.5 V VDD 5.5 V 38 500 high-/low-level width 3.0 V VDD < 4.5 V 50 500 (tXH, tXL) 1.8 V VDD < 3.0 V 85 500 ms MHz ns Notes 1. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time. 2. Time required to stabilize oscillation after reset or STOP mode release. Cautions 1. When using the main system clock oscillator, wire as follows in the area enclosed by the broken lines in the above figures to avoid an adverse effect from wiring capacitance. * Keep the wiring length as short as possible. * Do not cross the wiring with the other signal lines. * Do not route the wiring near a signal line through which a high fluctuating current flows. * Always make the ground point of the oscillator capacitor the same potential as VSS1. * Do not ground the capacitor to a ground pattern through which a high current flows. * Do not fetch signals from the oscillator. 2. When the main system clock is stopped and the system is operating on the subsystem clock, wait until the oscillation stabilization time has been secured by the program before switching back to the main system clock. 488 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Subsystem Clock Oscillator Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Resonator Crystal resonator Recommended Circuit XT2 R C4 External clock XT1 VSS1 XT2 C3 XT1 Conditions Parameter Oscillation frequency (fXT)Note 1 Oscillation stabilization timeNote 2 MIN. TYP. MAX. Unit 32 32.768 35 kHz 1.2 2 s 4.0 V VDD 5.5 V 10 1.8 V VDD < 4.0 V XT1 input frequency (fXT)Note 1 32 38.5 kHz XT1 input high-/low-level width (tXTH, tXTL) 12 15 s Notes 1. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time. 2. Time required to stabilize oscillation after VDD reaches oscillation voltage range MIN. Cautions 1. When using the subsystem clock oscillator, wire as follows in the area enclosed by the broken lines in the above figure to avoid an adverse effect from wiring capacitance. * Keep the wiring length as short as possible. * Do not cross the wiring with the other signal lines. * Do not route the wiring near a signal line through which a high fluctuating current flows. * Always make the ground point of the oscillator capacitor the same potential as VSS1. * Do not ground the capacitor to a ground pattern through which a high current flows. * Do not fetch signals from the oscillator. 2. The subsystem clock oscillator is designed as a low-amplitude circuit for reducing power consumption, and is more prone to malfunction due to noise than the main system clock oscillator. Particular care is therefore required with the wiring method when the subsystem clock is used. Remark For the resonator selection and oscillator constant of the subsystem clock, customers are required to either evaluate the oscillation themselves or apply to the resonator manufacturer for evaluation. User's Manual U14046EJ5V0UD 489 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Recommended Oscillator Constant To use the PD78F0034B or 78F0034B(A), for the resonator selection and oscillator constant, customers are required to either evaluate the oscillation themselves or apply to the resonator manufacturer for evaluation. * Mask ROM versions of PD780024A, 780034A Subseries (expanded-specification product) Main system clock: Ceramic resonator (TA = -40 to +85C) Manufacturer Part Number Frequency (MHz) Recommended Circuit Constant Oscillation Voltage Range C1 (pF) C2 (pF) R1 (k) MIN. (V) MAX. (V) 100 100 2.2 1.8 5.5 Murata Mfg. CSBFB1M00J58 1.00 Co., Ltd. CSBLA1M00J58 1.00 100 100 2.2 1.8 5.5 CSTCC2M00G56 2.00 On-chip On-chip 0 1.8 5.5 TDK CSTLS2M00G56 2.00 On-chip On-chip 0 1.8 5.5 CSTCC3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTLS3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTCR4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTLS4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTCR4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTLS4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTCR4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTLS4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTCR5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTLS5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTCE8M00G52 8.00 On-chip On-chip 0 2.7 5.5 CSTLS8M00G53 8.00 On-chip On-chip 0 2.7 5.5 CSTCE8M38G52 8.38 On-chip On-chip 0 3.0 5.5 CSTLS8M38G53 8.38 On-chip On-chip 0 3.0 5.5 CSTCE10M0G52 10.00 On-chip On-chip 0 3.0 5.5 CSTLS10M0G53 10.00 On-chip On-chip 0 3.0 5.5 CSTCE12M0G52 12.00 On-chip On-chip 0 4.5 5.5 CSTLA12M0T55 12.00 On-chip On-chip 0 4.5 5.5 CCR3.58MC3 3.58 On-chip On-chip 0 1.8 5.5 CCR4.19MC3 4.19 On-chip On-chip 0 1.8 5.5 CCR5.0MC3 5.00 On-chip On-chip 0 1.8 5.5 CCR8.0MC5 8.00 On-chip On-chip 0 2.7 5.5 CCR8.38MC5 8.38 On-chip On-chip 0 3.0 5.5 Caution The oscillator constant is a reference value based on evaluation in specific environments by the resonator manufacturer. If the oscillator characteristics need to be optimized in the actual application, request the resonator manufacturer for evaluation on the implementation circuit. Note that the oscillation voltage and oscillation frequency merely indicate the characteristics of the oscillator. Use the internal operation conditions of the PD780024A, 780034A Subseries within the specifications of the DC and AC characteristics. 490 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (1/4) Parameter Symbol Output current, high IOH Output current, low IOL Input voltage, high VIH1 VIH2 VIH3 VIH4 VIH5 Input voltage, VIL1 low VIL2 VIL3 VIL4 Conditions MAX. Unit Per pin -1 mA All pins -15 mA Per pin for P00 to P03, P20 to P25, P34 to P36, P40 to P47, P64 to P67, P70 to P75 10 mA Per pin for P30 to P33, P50 to P57 15 mA Total for P00 to P03, P40 to P47, P64 to P67, P70 to P75 20 mA Total for P20 to P25 10 mA Total for P30 to P36 70 mA Total for P50 to P57 70 mA P10 to P17, P21, P24, P35, P40 to P47, P50 to P57, P64 to P67, P74, P75 MIN. TYP. 2.7 V VDD 5.5 V 0.7VDD VDD V 1.8 V VDD < 2.7 V 0.8VDD VDD V V 2.7 V VDD 5.5 V 0.8VDD VDD P34, P36, P70 to P73, RESET 1.8 V VDD < 2.7 V 0.85VDD VDD V P30 to P33 2.7 V VDD 5.5 V 0.7VDD 5.5 V (N-ch open-drain) 1.8 V VDD < 2.7 V 0.8VDD 5.5 V X1, X2 2.7 V VDD 5.5 V VDD - 0.5 VDD V 1.8 V VDD < 2.7 V VDD - 0.2 VDD V 4.0 V VDD 5.5 V 0.8VDD VDD V 1.8 V VDD < 4.0 V 0.9VDD VDD V P10 to P17, P21, P24, P35, P40 to P47, P50 to P57, P64 to P67, P74, P75 2.7 V VDD 5.5 V 0 0.3VDD V 1.8 V VDD < 2.7 V 0 0.2VDD V P00 to P03, P20, P22, P23, P25, 2.7 V VDD 5.5 V 0 0.2VDD V P34, P36, P70 to P73, RESET 1.8 V VDD < 2.7 V 0 0.15VDD V P30 to P33 4.0 V VDD 5.5 V 0 0.3VDD V 2.7 V VDD < 4.0 V 0 0.2VDD V 1.8 V VDD < 2.7 V 0 0.1VDD V 2.7 V VDD 5.5 V 0 0.4 V 1.8 V VDD < 2.7 V 0 0.2 V 4.0 V VDD 5.5 V 0 0.2VDD V P00 to P03, P20, P22, P23, P25, XT1, XT2 X1, X2 VIL5 XT1, XT2 0 0.1VDD V Output voltage, high VOH1 4.0 V VDD 5.5 V, IOH = -1 mA VDD - 1.0 VDD V 1.8 V VDD < 4.0 V, IOH = -100 A VDD - 0.5 VDD V Output voltage, low VOL1 P30 to P33 2.0 V VOL2 P50 to P57 2.0 V VOL3 P00 to P03, P20 to P25, P34 to P36, 4.0 V VDD 5.5 V, P40 to P47, P64 to P67, P70 to P75 IOL = 1.6 mA 0.4 V VOL4 IOL = 400 A 0.5 V 1.8 V VDD < 4.0 V Remark 4.0 V VDD 5.5 V, IOL = 15 mA 0.4 Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. User's Manual U14046EJ5V0UD 491 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (2/4) Parameter Input leakage current, high Symbol ILIH1 Conditions VIN = VDD TYP. MAX. Unit P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, RESET 3 A X1, X2, XT1, XT2 20 A ILIH3 VIN = 5.5 V P30 to P33 3 A ILIL1 VIN = 0 V P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, RESET -3 A X1, X2, XT1, XT2 -20 A P30 to P33 ILIH2 Input leakage current, low MIN. ILIL2 -3 A Output leakage current, high ILOH VOUT = VDD 3 A Output leakage ILOL VOUT = 0 V -3 A Mask option pullup resistance (mask ROM version only) R1 VIN = 0 V, P30, P31, P32, P33 15 30 90 k Software pull- R2 VIN = 0 V, P00 to P03, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75 15 30 90 k ILIL3 current, low up resistance Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. 492 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (3/4) (1) Mask ROM versions of PD780024A, 780034A Subseries (expanded-specification product) Parameter Symbol Conditions Power supply currentNote 1 IDD1Note 2 10%Note 3 TYP. MAX. Unit When A/D converter is stopped When A/D converter is operatingNote 7 8.5 17 mA 9.5 19 mA 8.38 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When A/D converter is stopped 5.5 11 mA operating mode When A/D converter is operatingNote 7 6.5 13 mA VDD = 3.0 V + 10%Notes 3, 6 When A/D converter is stopped 3 6 mA When A/D converter is operatingNote 7 4 8 mA 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When A/D converter is stopped 2 4 mA operating mode When A/D converter is operatingNote 7 3 6 mA When A/D converter is stopped 0.4 1.5 mA When A/D converter is operatingNote 7 1.4 4.2 mA 2 4 mA 10 mA 2.2 mA 4.7 mA 1 mA 4 mA 0.7 mA 1.7 mA 0.4 mA 1.1 mA 12.0 MHz VDD = 5.0 V crystal oscillation operating mode VDD = 2.0 V 10%Note 4 IDD2 MIN. 12.0 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped HALT mode When peripheral functions are operating 8.38 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped HALT mode When peripheral functions are operating VDD = 3.0 V + 10%Notes 3, 6 When peripheral functions are stopped 1.1 0.5 When peripheral functions are operating 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped HALT mode When peripheral functions are operating VDD = 2.0 V 10%Note 4 When peripheral functions are stopped 0.35 0.15 When peripheral functions are operating IDD3 IDD4 IDD5 32.768 kHz crystal oscillation operating modeNote 5 VDD = 5.0 V 10% 40 80 A VDD = 3.0 V 10% 20 40 A VDD = 2.0 V 10% 10 20 A 32.768 kHz crystal oscillation HALT modeNote 5 VDD = 5.0 V 10% 30 60 A VDD = 3.0 V 10% 6 18 A VDD = 2.0 V 10% 2 10 A XT1 = VDD, STOP mode When feedback resistor is not used VDD = 5.0 V 10% 0.1 30 A VDD = 3.0 V 10% 0.05 10 A VDD = 2.0 V 10% 0.05 10 A User's Manual U14046EJ5V0UD 493 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Notes 1. Total current through the internal power supply (VDD0, VDD1) (except the current through pull-up resistors of ports). 2. IDD1 includes the peripheral operation current. 3. When the processor clock control register (PCC) is cleared to 00H. 4. When PCC is set to 02H. 5. When main system clock operation is stopped. 6. The values show the specifications when VDD = 3.0 to 3.3 V. The value in the TYP. column show the specifications when VDD = 3.0 V. 7. Includes the current through the AVDD pin. 494 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (4/4) (2) PD78F0034B, 78F0034B(A) Parameter Symbol Conditions Power supply currentNote 1 IDD1Note 2 10%Note 3 TYP. MAX. Unit When A/D converter is stopped When A/D converter is operatingNote 7 16 32 mA 17 34 mA 8.38 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When A/D converter is stopped 10.5 21 mA operating mode When A/D converter is operatingNote 7 11.5 23 mA VDD = 3.0 V + 10%Notes 3, 6 When A/D converter is stopped 7 14 mA When A/D converter is operatingNote 7 8 16 mA 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When A/D converter is stopped 4.5 9 mA operating mode When A/D converter is operatingNote 7 5.5 11 mA When A/D converter is stopped 1 2 mA When A/D converter is operatingNote 7 2 6 mA 12.0 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped 2 4 mA HALT mode When peripheral functions are operating 8 mA 8.38 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped 2.4 mA HALT mode When peripheral functions are operating 5 mA 1.2 mA 2.4 mA 0.8 mA 1.7 mA 0.4 mA 1.1 mA 12.0 MHz VDD = 5.0 V crystal oscillation operating mode VDD = 2.0 V 10%Note 4 IDD2 MIN. VDD = 3.0 V + 10%Notes 3, 6 When peripheral functions are stopped 1.2 0.6 When peripheral functions are operating 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped HALT mode When peripheral functions are operating VDD = 2.0 V 10%Note 4 When peripheral functions are stopped 0.4 0.2 When peripheral functions are operating IDD3 IDD4 IDD5 32.768 kHz crystal oscillation operating modeNote 5 VDD = 5.0 V 10% 115 230 A VDD = 3.0 V 10% 95 190 A VDD = 2.0 V 10% 75 150 A 32.768 kHz crystal oscillation HALT modeNote 5 VDD = 5.0 V 10% 30 60 A VDD = 3.0 V 10% 6 18 A VDD = 2.0 V 10% 2 10 A XT1 = VDD, STOP mode When feedback resistor is not used VDD = 5.0 V 10% 0.1 30 A VDD = 3.0 V 10% 0.05 10 A VDD = 2.0 V 10% 0.05 10 A User's Manual U14046EJ5V0UD 495 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Notes 1. Total current through the internal power supply (VDD0, VDD1) (except the current through pull-up resistors of ports). 2. IDD1 includes the peripheral operation current. 3. When the processor clock control register (PCC) is cleared to 00H. 4. When PCC is set to 02H. 5. When main system clock operation is stopped. 6. The values show the specifications when VDD = 3.0 to 3.3 V. The value in the TYP. column show the specifications when VDD = 3.0 V. 7. Includes the current through the AVDD pin. 496 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) AC Characteristics (1) Basic operation (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Parameter Symbol Cycle time (Min. instruction execution time) TCY Conditions Operating with main system clock MIN. MAX. Unit 4.5 V VDD 5.5 V 0.166 16 s 3.0 V VDD < 4.5 V 0.238 16 s 2.7 V VDD < 3.0 V 0.4 16 s 1.8 V VDD < 2.7 V 1.6 16 s 125 s 103.9Note 1 Operating with subsystem clock 122 3.0 V VDD 5.5 V 2/fsam + 0.1Note 2 s 2.7 V VDD < 3.0 V 2/fsam + 0.2Note 2 s 1.8 V VDD < 2.7 V 0.5Note 2 s TI00, TI01 input high-/low-level width tTIH0, tTIL0 TI50, TI51 input fTI5 2.7 V VDD 5.5 V TI50, TI51 input high-/low-level width tTIH5, tTIL5 1.8 V VDD < 2.7 V Interrupt request input high-/lowlevel width tINTH, tINTL RESET low-level width tRSL frequency TYP. 2/fsam + 0 4 MHz 1.8 V VDD < 2.7 V 0 275 kHz 2.7 V VDD 5.5 V 100 ns 1.8 s 2.7 V VDD 5.5 V 1 s 1.8 V VDD < 2.7 V 2 s 2.7 V VDD 5.5 V 10 s 1.8 V VDD < 2.7 V 20 s INTP0 to INTP3, P40 to P47 Notes 1. Value when the external clock is used. When a crystal resonator is used, it is 114 s (MIN.). 2. Selection of fsam = fX, fX/4, fX/64 is possible using bits 0 and 1 (PRM00, PRM01) of prescaler mode register 0 (PRM0). However, if the TI00 valid edge is selected as the count clock, the value becomes fsam = fX/8. User's Manual U14046EJ5V0UD 497 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) TCY vs. VDD (main system clock operation) 16.0 Cycle time TCY [ S] 10.0 5.0 Operation guaranteed range 2.0 1.6 1.0 0.4 0.238 0.166 0.1 0 1.0 2.0 1.8 3.0 2.7 4.0 4.5 Supply voltage VDD [V] 498 User's Manual U14046EJ5V0UD 5.0 5.5 6.0 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 4.0 to 5.5 V) (1/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 20 ns Address hold time tADH 6 ns Data input time from address tADD1 (2 + 2n)tCY - 54 ns tADD2 (3 + 2n)tCY - 60 ns 100 ns Address output time from RD tRDAD Data input time from RD tRDD1 (2 + 2n)tCY - 87 ns tRDD2 (3 + 2n)tCY - 93 ns 0 Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 33 ns tRDL2 (2.5 + 2n)tCY - 33 ns Input time from RD to WAIT tRDWT1 tCY - 43 ns tRDWT2 tCY - 43 ns Input time from WR to WAIT tWRWT tCY - 25 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 6 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 15 ns Delay time from ASTB to RD tASTRD 6 ns Delay time from ASTB to WR tASTWR 2tCY - 15 ns Delay time from tRDAST 0.8tCY - 15 1.2tCY ns tRDADH 0.8tCY - 15 1.2tCY + 30 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 10 60 ns Address hold time from WR tWRADH 0.8tCY - 15 1.2tCY + 30 ns Delay time from WAIT to RD tWTRD 0.8tCY 2.5tCY + 25 ns Delay time from WAIT to WR tWTWR 0.8tCY 2.5tCY + 25 ns RD to ASTB at external fetch Address hold time from RD at external fetch Caution Remarks ns TCY can only be used when the MIN. value is 0.238 s. 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) User's Manual U14046EJ5V0UD 499 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 2.7 to 4.0 V) (2/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 30 ns Address hold time tADH 10 ns Input time from address to data tADD1 (2 + 2n)tCY - 108 ns tADD2 (3 + 2n)tCY - 120 ns 200 ns Output time from RD to address tRDAD 0 Input time from RD to data tRDD1 (2 + 2n)tCY - 148 ns tRDD2 (3 + 2n)tCY - 162 ns Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 40 ns tRDL2 (2.5 + 2n)tCY - 40 ns Input time from RD to WAIT tRDWT1 tCY - 75 ns tRDWT2 tCY - 60 ns Input time from WR to WAIT tWRWT tCY - 50 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 10 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 30 ns Delay time from ASTB to RD tASTRD 10 ns Delay time from ASTB to WR tASTWR 2tCY - 30 ns Delay time from tRDAST 0.8tCY - 30 1.2tCY ns tRDADH 0.8tCY - 30 1.2tCY + 60 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 20 120 ns Hold time from WR to address tWRADH 0.8tCY - 30 1.2tCY + 60 ns Delay time from WAIT to RD tWTRD 0.5tCY 2.5tCY + 50 ns Delay time from WAIT to WR tWTWR 0.5tCY 2.5tCY + 50 ns RD to ASTB at external fetch Hold time from RD to address at external fetch Caution Remarks TCY can only be used when the MIN. value is 0.4 s. 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) 500 ns User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 1.8 to 2.7 V) (3/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 120 ns Address hold time tADH 20 ns Input time from address to data tADD1 (2 + 2n)tCY - 233 ns tADD2 (3 + 2n)tCY - 240 ns 400 ns Output time from RD to address tRDAD 0 Input time from RD to data tRDD1 (2 + 2n)tCY - 325 ns tRDD2 (3 + 2n)tCY - 332 ns Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 92 ns tRDL2 (2.5 + 2n)tCY - 92 ns Input time from RD to WAIT tRDWT1 tCY - 350 ns tRDWT2 tCY - 132 ns Input time from WR to WAIT tWRWT tCY - 100 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 20 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 60 ns Delay time from ASTB to RD tASTRD 20 ns Delay time from ASTB to WR tASTWR 2tCY - 60 ns Delay time from tRDAST 0.8tCY - 60 1.2tCY ns tRDADH 0.8tCY - 60 1.2tCY + 120 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 40 240 ns Hold time from WR to address tWRADH 0.8tCY - 60 1.2tCY + 120 ns Delay time from WAIT to RD tWTRD 0.5tCY 2.5tCY + 100 ns Delay time from WAIT to WR tWTWR 0.5tCY 2.5tCY + 100 ns RD to ASTB at external fetch Hold time from RD to address at external fetch Caution Remarks ns TCY can only be used when the MIN. value is 1.6 s. 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) User's Manual U14046EJ5V0UD 501 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) (3) Serial interface (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (1/2) (a) 3-wire serial I/O mode (SCK3n... Internal clock output) Parameter SCK3n Symbol tKCY1 cycle time SCK3n high-/ tKH1, tKL1 low-level width SI3n setup time tSIK1 (to SCK3n) SI3n hold time tKSI1 (from SCK3n) Delay time from tKSO1 Conditions MIN. TYP. MAX. Unit 4.5 V VDD 5.5 V 666 ns 3.0 V VDD < 4.5 V 954 ns 2.7 V VDD < 3.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns 3.0 V VDD 5.5 V tKCY1/2 - 50 ns 1.8 V VDD < 3.0 V tKCY1/2 - 100 ns 3.0 V VDD 5.5 V 100 ns 2.7 V VDD < 3.0 V 150 ns 1.8 V VDD < 2.7 V 300 ns 4.5 V VDD 5.5 V 300 ns 1.8 V VDD < 4.5 V 400 ns C = 100 pF Note SCK3n to SO3n output 4.5 V VDD 5.5 V 200 ns 1.8 V VDD < 4.5 V 300 ns MAX. Unit Note C is the load capacitance of the SCK3n and SO3n output lines. (b) 3-wire serial I/O mode (SCK3n... External clock input) Parameter SCK3n Symbol tKCY2 cycle time SCK3n high-/ tKH2, tKL2 low-level width SI3n setup time (to SCK3n) tSIK2 SI3n hold time tKSI2 (from SCK3n) Delay time from SCK3n to SO3n output tKSO2 Conditions TYP. 4.5 V VDD 5.5 V 666 ns 3.0 V VDD < 4.5 V 800 ns 2.7 V VDD < 3.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns 4.5 V VDD 5.5 V 333 ns 3.0 V VDD < 4.5 V 400 ns 2.7 V VDD < 3.0 V 800 ns 1.8 V VDD < 2.7 V 1600 ns 100 ns 4.5 V VDD 5.5 V 300 ns 1.8 V VDD < 4.5 V 400 ns C = 100 pF Note 4.5 V VDD 5.5 V 200 ns 1.8 V VDD < 4.5 V 300 ns Note C is the load capacitance of the SO3n output line. Remark n = 0, 1 502 MIN. User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) (3) Serial interface (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (2/2) (c) UART mode (dedicated baud-rate generator output) Parameter Symbol Transfer rate Conditions MIN. TYP. MAX. Unit 4.5 V VDD 5.5 V 187500 bps 3.0 V VDD < 4.5 V 131031 bps 2.7 V VDD < 3.0 V 78125 bps 1.8 V VDD < 2.7 V 39063 bps MAX. Unit (d) UART mode (external clock input) Parameter ASCK0 cycle time ASCK0 high-/low-level width Symbol Conditions MIN. TYP. 4.0 V VDD 5.5 V 800 ns 2.7 V VDD < 4.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns tKH3, 4.0 V VDD 5.5 V 400 ns tKL3 2.7 V VDD < 4.0 V 800 ns 1.8 V VDD < 2.7 V 1600 ns tKCY3 Transfer rate 4.0 V VDD 5.5 V 39063 bps 2.7 V VDD < 4.0 V 19531 bps 1.8 V VDD < 2.7 V 9766 bps MAX. Unit 131031 bps (e) UART mode (infrared data transfer mode) Parameter Transfer rate Symbol Conditions MIN. 4.0 V VDD 5.5 V Allowable bit rate error 4.0 V VDD 5.5 V Output pulse width 4.0 V VDD 5.5 V 1.2 Input pulse width 4.0 V VDD 5.5 V 4/fX 0.87 % 0.24/fbrNote s s Note fbr: Specified baud rate User's Manual U14046EJ5V0UD 503 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) A/D Converter Characteristics (TA = -40 to +85C, VDD = AVDD = 1.8 to 5.5 V, AVSS = VSS = 0 V) (1/2) (1) 8-bit A/D converter: PD780024A Subseries Parameter Symbol Conditions MIN. TYP. MAX. Unit 8 8 8 bit 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR Resolution Overall errorNote Conversion time tCONV Analog input voltage VAIN Reference voltage AVREF Resistance between AVREF and AVSS RREF 4.5 V AVDD 5.5 V 12 96 s 4.0 V AVDD < 4.5 V 14 96 s 2.7 V AVDD < 4.0 V 17 96 s 1.8 V AVDD < 2.7 V 28 96 s 0 AVREF V 1.8 AVDD V During A/D converter operation 20 40 k Note Excludes quantization error (1/2 LSB). This value is indicated as a ratio (%FSR) to the full-scale value. Remark The impedance of the analog input pins is shown below. [Equivalent circuit] R1 R2 ANIn (n = 0 to 3) C1 C2 C3 [Parameter value] (TYP.) 504 AVDD R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) A/D Converter Characteristics (TA = -40 to +85C, VDD = AVDD = 1.8 to 5.5 V, AVSS = VSS = 0 V) (2/2) (2) 10-bit A/D converter: PD780034A Subseries Parameter Symbol Conditions MIN. TYP. MAX. Unit 10 10 10 bit 4.0 V AVREF 5.5 V 0.2 0.4 %FSR 2.7 V AVREF < 4.0 V 0.3 0.6 %FSR 1.8 V AVREF < 2.7 V 0.6 1.2 %FSR Resolution Overall errorNotes 1, 2 Conversion time Zero-scale Full-scale tCONV errorNotes 1, 2 errorNotes 1, 2 Integral linearity errorNote 1 Differential linearity error Analog input voltage VAIN Reference voltage AVREF Resistance between AVREF and AVSS RREF 4.5 V AVDD 5.5 V 12 96 s 4.0 V AVDD < 4.5 V 14 96 s 2.7 V AVDD < 4.0 V 17 96 s 1.8 V AVDD < 2.7 V 28 96 s 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR 4.0 V AVREF 5.5 V 2.5 LSB 2.7 V AVREF < 4.0 V 4.5 LSB 1.8 V AVREF < 2.7 V 8.5 LSB 4.0 V AVREF 5.5 V 1.5 LSB 2.7 V AVREF < 4.0 V 2.0 LSB 1.8 V AVREF < 2.7 V 3.5 LSB 0 AVREF V 1.8 AVDD V During A/D converter operation 20 40 k Notes 1. Excludes quantization error (1/2 LSB). 2. This value is indicated as a ratio to the full-scale value. Remark The impedance of the analog input pins is shown below. [Equivalent circuit] R1 R2 ANIn (n = 0 to 3) C1 C2 C3 [Parameter value] (TYP.) AVDD R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF User's Manual U14046EJ5V0UD 505 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Data Memory STOP Mode Low Supply Voltage Data Retention Characteristics (TA = -40 to +85C) Parameter Symbol Data retention power supply voltage VDDDR Data retention power IDDDR supply current Release signal set time Oscillation stabilization wait time Conditions TYP. 1.6 VDDDR = 1.6 V (Subsystem clock unused (XT1 = VDD) and feedback resistor disconnected) tSREL tWAIT MIN. 0.1 MAX. Unit 5.5 V 30 A s 0 Release by RESET 217/fX s Release by interrupt request Note s Note Selection of 212/fX and 214/fX to 217/fX is possible using bits 0 to 2 (OSTS0 to OSTS2) of the oscillation stabilization time select register (OSTS). 506 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Flash Memory Programming Characteristics (1/2) (TA = +10 to +40C, VDD = AVDD = 1.8 to 5.5 V, VSS = AVSS = 0 V) * PD78F0034B, 78F0034B(A) (a) Write erase characteristics Parameter Symbol Operating frequency fX VPP supply voltage VDD supply current VPP2 Note 1 IDD VPP supply current Step erase time Overall erase time Writeback time IPP Note 2 Tera Cwb Number of erases/writebacks Cerwb Note 6 Number of rewrites per chip Note 8 MAX. Unit 1.0 10.0 MHz 3.0 V VDD < 4.5 V 1.0 8.38 MHz 2.7 V VDD < 3.0 V 1.0 5.00 MHz 1.8 V VDD < 2.7 V 1.0 1.25 MHz During flash memory programming 9.7 10.3 V VDD = 5.0 V10% 30 mA 8.38 MHz crystal VDD = 5.0 V10% 24 mA oscillation operating mode 17 mA 100 mA 0.201 s 20 s/chip 50.6 ms 60 Times 16 Times 52 s 520 s 20 Times/area When 10 MHz crystal VPP = VPP2 oscillation operating mode 10.0 VDD = 3.0 V10% When VPP = VPP2 0.199 0.2 When step erase time = 0.2 s 49.4 50 When writeback time = 50 ms Twr Note 7 TYP. 4.5 V VDD 5.5 V Twb Number of writebacks per Note 5 writeback command Overall write time per word MIN. Ter Note 3 Note 4 Step write time Conditions 48 Twrw When step write time = 50 s (1 word = 1 byte) Cerwr 1 erase + 1 write after erase = 1 rewrite 48 50 Notes 1. 2. 3. 4. 5. AVDD current and port current (current that flows through the internal pull-up resistor) are not included. The recommended setting value of the step erase time is 0.2 s. The prewrite time before erasure and the erase verify time (writeback time) are not included. The recommended setting value of the writeback time is 50 ms. Writeback is executed once by the issuance of the writeback command. Therefore, the number of retries must be the maximum value minus the number of commands issued. 6. The recommended setting value of the step write time is 50 s. 7. The actual write time per word is 100 s longer. The internal verify time during or after a write is not included. 8. When a product is first written after shipment, "erase write" and "write only" are both taken as one rewrite. Example: P: Write, E: Erase Shipped product PEPEP: 3 rewrites Shipped product EPEPEP: 3 rewrites User's Manual U14046EJ5V0UD 507 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Flash Memory Programming Characteristics (2/2) (TA = +10 to +40C, VDD = AVDD = 1.8 to 5.5 V, VSS = AVSS = 0 V) * PD78F0034B, 78F0034B(A) (b) Serial write operation characteristics Parameter Symbol Conditions MIN. TYP. MAX. Unit Set time from VDD to VPP tDP 10 s Release time from VPP to RESET tPR 1.0 s VPP pulse input start time from RESET tRP 1.0 s VPP pulse high-/low-level width tPW 8.0 s VPP pulse input end time from RESET tRPE VPP pulse low-level input voltage VPPL 0.8VDD VPP pulse high-level input voltage VPPH 9.7 508 User's Manual U14046EJ5V0UD 10.0 20 ms 1.2VDD V 10.3 V CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Timing Charts AC Timing Test Points (excluding X1, XT1 input) 0.8VDD 0.2VDD 0.8VDD Test points 0.2VDD Clock Timing 1/fX tXL tXH VIH4 (MIN.) VIL4 (MAX.) X1 input 1/fXT tXTL tXTH VIH5 (MIN.) VIL5 (MAX.) XT1 input TI Timing tTIL0 tTIH0 TI00, TI01 1/fTI5 tTIL5 tTIH5 TI50, TI51 User's Manual U14046EJ5V0UD 509 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Interrupt Request Input Timing tINTL tINTH INTP0 to INTP3 RESET Input Timing tRSL RESET 510 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Read/Write Operation External fetch (no wait): A8 to A15 Higher 8-bit address tADD1 AD0 to AD7 Hi-Z Lower 8-bit address tADS Instruction code tRDAD tRDD1 tADH tRDADH tASTH tRDAST ASTB RD tASTRD tRDL1 tRDH External fetch (wait insertion): A8 to A15 Higher 8-bit address tADD1 AD0 to AD7 Hi-Z Lower 8-bit address tADS tADH tRDAD Instruction code tRDADH tRDD1 tASTH tRDAST ASTB RD tASTRD tRDL1 tRDH WAIT tRDWT1 tWTL User's Manual U14046EJ5V0UD tWTRD 511 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) External data access (no wait): A8 to A15 Higher 8-bit address tADD2 AD0 to AD7 Hi-Z tRDAD tRDD2 Lower 8-bit address tADS tADH tASTH Hi-Z Write data Read data tRDH ASTB RD tASTRD tRDWD tRDL2 tWDS tWDH tWRADH tWRWD WR tASTWR tWRL1 External data access (wait insertion): A8 to A15 Higher 8-bit address tADD2 AD0 to AD7 Lower 8-bit address tADS tADH tASTH Hi-Z Read data Hi-Z Write data tRDAD tRDH tRDD2 ASTB tASTRD RD tRDWD tRDL2 tWDH tWDS tWRWD WR tASTWR tWRL1 tWRADH WAIT tRDWT2 tWTL tWTRD tWTL tWRWT 512 User's Manual U14046EJ5V0UD tWTWR CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Serial Transfer Timing 3-wire serial I/O mode: tKCYm tKLm tKHm SCK3n tSIKm tKSIm Input data SI3n tKSOm SO3n Output data Remarks 1. m = 1, 2 2. n = 0, 1 UART mode (external clock input): t KCY3 t KL3 t KH3 ASCK0 User's Manual U14046EJ5V0UD 513 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Data Retention Timing (STOP Mode Release by RESET) Internal reset operation HALT mode Operating mode STOP mode Data retention mode VDD VDDDR tSREL STOP instruction execution RESET tWAIT Data Retention Timing (Standby Release Signal: STOP Mode Release by Interrupt Request Signal) HALT mode Operating mode STOP mode Data retention mode VDD VDDDR tSREL STOP instruction execution Standby release signal (interrupt request) tWAIT 514 User's Manual U14046EJ5V0UD CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) Flash Memory Write Mode Set Timing VDD VDD 0V tDP tRP tPW VPPH VPP VPPL tPW 0V tPR tRPE VDD RESET (input) 0V User's Manual U14046EJ5V0UD 515 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Target products * PD780021A, 780022A, 780023A, 780024A, 780031A, 780032A, 780033A, 780034A, 780021A(A), 780022A(A), 780023A(A), 780024A(A), 780031A(A), 780032A(A), 780033A(A), 780034A(A) for which orders were received before November 30, 2001 (Products with rankNote K, E, P, X) * PD780021AY, 780022AY, 780023AY, 780024AY, 780031AY, 780032AY, 780033AY, 780034AY, 780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A), 780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A) * PD78F0034A, 78F0034AY, 78F0034BY, 78F0034BY(A) Note The rank is indicated by the 5th digit from the left in the lot number marked on the package. x x x x Lot number Year Week code code Rank Caution The PD780021AY(A), 780023AY(A), 780024AY(A), 780031AY(A), 780032AY(A), 780033AY(A), and 780034AY(A) are under development. The electrical specifications of the above products are target values (reference values only); mass-produced products do not necessarily satisfy these ratings. 516 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Absolute Maximum Ratings (TA = 25C) (1/2) Parameter Symbol Supply voltage Conditions Ratings Unit -0.3 to +6.5 V -0.3 to +10.5 V AVDD -0.3 to VDD + 0.3Note 1 V AVREF -0.3 to VDD + 0.3Note 1 V AVSS -0.3 to +0.3 V -0.3 to VDD + 0.3Note 1 V -0.3 to +6.5 V -0.3 to VDD + 0.3Note 1 V -0.3 to VDD + 0.3Note 1 V AVSS - 0.3 to AVREF + 0.3Note 1 and -0.3 to VDD + 0.3Note 1 V VDD VPP Input voltage Flash memory version only, Note 2 VI1 P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, X1, X2, XT1, XT2, RESET VI2 P30 to P33 N-ch open drain On-chip pull-up resistor Output voltage VO Analog input voltage VAN P10 to P17 Analog input pin Notes 1. 6.5 V or below 2. Make sure that the following conditions of the VPP voltage application timing are satisfied when the flash memory is written. * When supply voltage rises VPP must exceed VDD 10 s or more after VDD has reached the lower-limit value (1.8 V) of the operating voltage range (see a in the figure below). * When supply voltage drops VDD must be lowered 10 s or more after VPP falls below the lower-limit value (1.8 V) of the operating voltage range of VDD (see b in the figure below). VDD 1.8 V 0V a b VPP 1.8 V 0V Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. User's Manual U14046EJ5V0UD 517 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Absolute Maximum Ratings (TA = 25C) (2/2) Parameter Output current, high Symbol IOH Conditions Ratings Unit Per pin -10 mA Total for P00 to P03, P40 to P47, P50 to P57, -15 mA Total for P20 to P25, P30 to P36 -15 mA Per pin for P00 to P03, P20 to P25, P34 to P36, P40 to P47, P64 to P67, P70 to P75 20 mA Per pin for P30 to P33, P50 to P57 30 mA Total for P00 to P03, P40 to P47, P64 to P67, P70 to P75 50 mA Total for P20 to P25 20 mA Total for P30 to P36 100 mA Total for P50 to P57 100 mA During normal operation -40 to +85 C During flash memory programming -10 to +80 C Mask ROM version -65 to +150 C Flash memory version -40 to +125 C P64 to P67, P70 to P75 Output current, low Operating ambient IOL TA temperature Storage Tstg temperature Caution Product quality may suffer if the absolute maximum rating is exceeded even momentarily for any parameter. That is, the absolute maximum ratings are rated values at which the product is on the verge of suffering physical damage, and therefore the product must be used under conditions that ensure that the absolute maximum ratings are not exceeded. Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. 518 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Capacitance (TA = 25C, VDD = VSS = 0 V) Parameter Symbol Conditions MIN. TYP. MAX. Unit Input capacitance CIN f = 1 MHz Unmeasured pins returned to 0 V. 15 pF I/O CIO f = 1 MHz Unmeasured pins returned to 0 V. P00 to P03, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75 15 pF P30 to P33 20 pF capacitance Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. Main System Clock Oscillator Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Resonator Ceramic resonator Recommended Circuit X2 X1 VSS1 Parameter C1 MIN. TYP. MAX. Unit MHz Oscillation frequency (fX)Note 1 4.0 V VDD 5.5 V 1.0 8.38 1.8 V VDD < 4.0 V 1.0 5.0 Oscillation stabilization timeNote 2 After VDD reaches oscillation voltage range R1 C2 Conditions 4 ms MHz MIN. Crystal resonator X2 C2 External clock X1 VSS1 R1 X2 C1 X1 Oscillation frequency (fX)Note 1 4.0 V VDD 5.5 V 1.0 8.38 1.8 V VDD < 4.0 V 1.0 5.0 Oscillation stabilization timeNote 2 4.0 V VDD 5.5 V 10 1.8 V VDD < 4.0 V 30 X1 input frequency (fX)Note 1 4.0 V VDD 5.5 V 1.0 1.8 V VDD < 4.0 V 1.0 5.0 X1 input high-/low-level width (tXH, tXL) 4.0 V VDD 5.5 V 50 500 1.8 V VDD < 4.0 V 85 500 8.38 ms MHz ns Notes 1. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time. 2. Time required to stabilize oscillation after reset or STOP mode release. Cautions 1. When using the main system clock oscillator, wire as follows in the area enclosed by the broken lines in the above figures to avoid an adverse effect from wiring capacitance. * Keep the wiring length as short as possible. * Do not cross the wiring with the other signal lines. * Do not route the wiring near a signal line through which a high fluctuating current flows. * Always make the ground point of the oscillator capacitor the same potential as VSS1. * Do not ground the capacitor to a ground pattern through which a high current flows. * Do not fetch signals from the oscillator. 2. When the main system clock is stopped and the system is operating on the subsystem clock, wait until the oscillation stabilization time has been secured by the program before switching back to the main system clock. User's Manual U14046EJ5V0UD 519 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Subsystem Clock Oscillator Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Resonator Crystal resonator Recommended Circuit XT2 R C4 External clock XT1 VSS1 XT2 C3 XT1 Parameter Conditions Oscillation frequency (fXT)Note 1 Oscillation stabilization timeNote 2 MIN. TYP. MAX. Unit 32 32.768 35 kHz 1.2 2 s 4.0 V VDD 5.5 V 10 1.8 V VDD < 4.0 V XT1 input frequency (fXT)Note 1 32 38.5 kHz XT1 input high-/low-level width (tXTH, tXTL) 12 15 s Notes 1. Indicates only oscillator characteristics. Refer to AC Characteristics for instruction execution time. 2. Time required to stabilize oscillation after VDD reaches oscillation voltage range MIN. Cautions 1. When using the subsystem clock oscillator, wire as follows in the area enclosed by the broken lines in the above figure to avoid an adverse effect from wiring capacitance. * Keep the wiring length as short as possible. * Do not cross the wiring with the other signal lines. * Do not route the wiring near a signal line through which a high fluctuating current flows. * Always make the ground point of the oscillator capacitor the same potential as VSS1. * Do not ground the capacitor to a ground pattern through which a high current flows. * Do not fetch signals from the oscillator. 2. The subsystem clock oscillator is designed as a low-amplitude circuit for reducing power consumption, and is more prone to malfunction due to noise than the main system clock oscillator. Particular care is therefore required with the wiring method when the subsystem clock is used. Remark For the resonator selection and oscillator constant of the subsystem clock, customers are required to either evaluate the oscillation themselves or apply to the resonator manufacturer for evaluation. 520 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Recommended Oscillator Constant (1/2) To use the PD78F0034BY or 78F0034BY(A), for the resonator selection and oscillator constant, customers are required to either evaluate the oscillation themselves or apply to the resonator manufacturer for evaluation. (1) Mask ROM versions of PD780024A, 780034A Subseries (conventional product) and PD780024AY, 780034AY Subseries Main system clock: Ceramic resonator (TA = -40 to +85C) Manufacturer Part Number Frequency (MHz) Recommended Circuit Constant Oscillation Voltage Range C1 (pF) C2 (pF) R1 (k) MIN. (V) MAX. (V) 100 100 2.2 1.8 5.5 Murata Mfg. CSBFB1M00J58 1.00 Co., Ltd. CSBLA1M00J58 1.00 100 100 2.2 1.8 5.5 CSTCC2M00G56 2.00 On-chip On-chip 0 1.8 5.5 TDK CSTLS2M00G56 2.00 On-chip On-chip 0 1.8 5.5 CSTCC3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTLS3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTCR4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTLS4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTCR4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTLS4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTCR4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTLS4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTCR5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTLS5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTCE8M00G52 8.00 On-chip On-chip 0 2.7 5.5 CSTLS8M00G53 8.00 On-chip On-chip 0 2.7 5.5 CSTCE8M38G52 8.38 On-chip On-chip 0 4.0 5.5 CSTLS8M38G53 8.38 On-chip On-chip 0 4.0 5.5 CCR3.58MC3 3.58 On-chip On-chip 0 1.8 5.5 CCR4.19MC3 4.19 On-chip On-chip 0 1.8 5.5 CCR5.0MC3 5.00 On-chip On-chip 0 1.8 5.5 CCR8.0MC5 8.00 On-chip On-chip 0 2.7 5.5 CCR8.38MC5 8.38 On-chip On-chip 0 4.0 5.5 Caution The oscillator constant is a reference value based on evaluation in specific environments by the resonator manufacturer. If the oscillator characteristics need to be optimized in the actual application, request the resonator manufacturer for evaluation on the implementation circuit. Note that the oscillation voltage and oscillation frequency merely indicate the characteristics of the oscillator. Use the internal operation conditions of the PD780024A, 780024AY, 780034A, 780034AY Subseries within the specifications of the DC and AC characteristics. User's Manual U14046EJ5V0UD 521 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Recommended Oscillator Constant (2/2) (2) PD78F0034A, 78F0034AY Main system clock: Ceramic resonator (TA = -40 to +85C) Manufacturer Part Number Frequency (MHz) Recommended Circuit Constant Oscillation Voltage Range C1 (pF) C2 (pF) R1 (k) MIN. (V) MAX. (V) 100 100 2.2 1.9 5.5 Murata Mfg. CSBFB1M00J58 1.00 Co., Ltd. CSBLA1M00J58 1.00 100 100 2.2 1.9 5.5 CSTCC2M00G56 2.00 On-chip On-chip 0 1.8 5.5 CSTLS2M00G56 2.00 On-chip On-chip 0 1.8 5.5 CSTCC3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTLS3M58G53 3.58 On-chip On-chip 0 1.8 5.5 CSTCR4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTLS4M00G53 4.00 On-chip On-chip 0 1.8 5.5 CSTCR4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTLS4M19G53 4.19 On-chip On-chip 0 1.8 5.5 CSTCR4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTLS4M91G53 4.91 On-chip On-chip 0 1.8 5.5 CSTCR5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTLS5M00G53 5.00 On-chip On-chip 0 1.8 5.5 CSTCE8M00G52 8.00 On-chip On-chip 0 2.7 5.5 CSTLS8M00G53 8.00 On-chip On-chip 0 2.7 5.5 CSTLS8M00G53093 8.00 On-chip On-chip 0 2.7 5.5 CSTCE8M38G52 8.38 On-chip On-chip 0 4.0 5.5 CSTLS8M38G53 8.38 On-chip On-chip 0 4.0 5.5 CSTLS8M38G53093 8.38 On-chip On-chip 0 4.0 5.5 CCR3.58MC3 3.58 On-chip On-chip 0 1.8 5.5 CCR4.19MC3 4.19 On-chip On-chip 0 1.8 5.5 CCR5.0MC3 5.00 On-chip On-chip 0 1.8 5.5 CCR8.0MC5 8.00 On-chip On-chip 0 2.7 5.5 CCR8.38MC5 8.38 On-chip On-chip 0 4.0 5.5 TDK Caution The oscillator constant is a reference value based on evaluation in specific environments by the resonator manufacturer. If the oscillator characteristics need to be optimized in the actual application, request the resonator manufacturer for evaluation on the implementation circuit. Note that the oscillation voltage and oscillation frequency merely indicate the characteristics of the oscillator. Use the internal operation conditions of the PD780024A, 780024AY, 780034A, 780034AY Subseries within the specifications of the DC and AC characteristics. 522 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (1/4) Parameter Symbol Output current, high IOH Output current, low IOL Input voltage, high VIH1 VIH2 VIH3 VIH4 VIH5 Input voltage, VIL1 low Conditions MIN. TYP. MAX. Unit Per pin -1 mA All pins -15 mA Per pin for P00 to P03, P20 to P25, P34 to P36, P40 to P47, P64 to P67, P70 to P75 10 mA Per pin for P30 to P33, P50 to P57 15 mA Total for P00 to P03, P40 to P47, P64 to P67, P70 to P75 20 mA Total for P20 to P25 10 mA Total for P30 to P36 70 mA Total for P50 to P57 70 mA 2.7 V VDD 5.5 V 0.7VDD VDD V 1.8 V VDD < 2.7 V 0.8VDD VDD V P00 to P03, P20, P22, P23, P25, 2.7 V VDD 5.5 V 0.8VDD VDD V P34, P36, P70 to P73, RESET 1.8 V VDD < 2.7 V 0.85VDD VDD V P30 to P33 2.7 V VDD 5.5 V 0.7VDD 5.5 V (N-ch open-drain) 1.8 V VDD < 2.7 V 0.8VDD 5.5 V X1, X2 2.7 V VDD 5.5 V VDD - 0.5 VDD V 1.8 V VDD < 2.7 V VDD - 0.2 VDD V 4.0 V VDD 5.5 V 0.8VDD VDD V 1.8 V VDD < 4.0 V 0.9VDD VDD V 2.7 V VDD 5.5 V 0 0.3VDD V 1.8 V VDD < 2.7 V 0 0.2VDD V P10 to P17, P21, P24, P35, P40 to P47, P50 to P57, P64 to P67, P74, P75 XT1, XT2 P10 to P17, P21, P24, P35, P40 to P47, P50 to P57, P64 to P67, P74, P75 VIL2 P00 to P03, P20, P22, P23, P25, P34, P36, P70 to P73, RESET 2.7 V VDD 5.5 V 0 0.2VDD V 1.8 V VDD < 2.7 V 0 0.15VDD V VIL3 P30 to P33 4.0 V VDD 5.5 V 0 0.3VDD V 2.7 V VDD < 4.0 V 0 0.2VDD V 1.8 V VDD < 2.7 V 0 0.1VDD V 2.7 V VDD 5.5 V 0 0.4 V 1.8 V VDD < 2.7 V 0 0.2 V 4.0 V VDD 5.5 V 0 0.2VDD V VIL4 X1, X2 VIL5 XT1, XT2 0 0.1VDD V Output voltage, high VOH1 4.0 V VDD 5.5 V, IOH = -1 mA VDD - 1.0 VDD V 1.8 V VDD < 4.0 V, IOH = -100 A VDD - 0.5 VDD V Output voltage, low VOL1 P30 to P33 2.0 V VOL2 P50 to P57 2.0 V VOL3 P00 to P03, P20 to P25, P34 to P36, 4.0 V VDD 5.5 V, P40 to P47, P64 to P67, P70 to P75 IOL = 1.6 mA 0.4 V VOL4 IOL = 400 A 0.5 V 1.8 V VDD < 4.0 V Remark 4.0 V VDD 5.5 V, IOL = 15 mA 0.4 Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. User's Manual U14046EJ5V0UD 523 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (2/4) Parameter Symbol Input leakage current, high ILIH1 Conditions VIN = VDD TYP. MAX. Unit P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, RESET 3 A X1, X2, XT1, XT2 20 A ILIH3 VIN = 5.5 V P30 to P33 3 A ILIL1 VIN = 0 V P00 to P03, P10 to P17, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75, RESET -3 A X1, X2, XT1, XT2 -20 A P30 to P33 ILIH2 Input leakage current, low MIN. ILIL2 -3 A Output leakage current, high ILOH VOUT = VDD 3 A Output leakage ILOL VOUT = 0 V -3 A Mask option pullup resistance (mask ROM version only) R1 VIN = 0 V, P30, P31, P32Note, P33Note 15 30 90 k Software pull- R2 VIN = 0 V, P00 to P03, P20 to P25, P34 to P36, P40 to P47, P50 to P57, P64 to P67, P70 to P75 15 30 90 k ILIL3 current, low up resistance Note PD780024A, 780034A Subseries only Remark Unless otherwise specified, the characteristics of alternate-function pins are the same as those of port pins. 524 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (3/4) (1) Mask ROM versions of PD780024A, 780034A Subseries (conventional product) and PD780024AY, 780034AY Subseries Parameter Symbol Conditions Power supply currentNote 1 IDD1Note 2 10%Note 3 TYP. MAX. Unit When A/D converter is stopped When A/D converter is operatingNote 6 5.5 11 mA 6.5 13 mA 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When A/D converter is stopped 2 4 mA operating mode When A/D converter is operatingNote 6 3 6 mA When A/D converter is stopped 0.4 1.5 mA When A/D converter is operatingNote 6 1.4 4.2 mA 8.38 MHz VDD = 5.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped 1.1 2.2 mA HALT mode When peripheral functions are operating 4.7 mA 5.00 MHz VDD = 3.0 V 10%Note 3 crystal oscillation When peripheral functions are stopped 0.7 mA HALT mode When peripheral functions are operating 1.7 mA 0.4 mA 1.1 mA 8.38 MHz VDD = 5.0 V crystal oscillation operating mode VDD = 2.0 V 10%Note 4 IDD2 VDD = 2.0 V 10%Note 4 MIN. When peripheral functions are stopped 0.35 0.15 When peripheral functions are operating IDD3 IDD4 IDD5 32.768 kHz crystal oscillation operating modeNote 5 VDD = 5.0 V 10% 40 80 A VDD = 3.0 V 10% 20 40 A VDD = 2.0 V 10% 10 20 A 32.768 kHz crystal oscillation HALT modeNote 5 VDD = 5.0 V 10% 30 60 A VDD = 3.0 V 10% 6 18 A VDD = 2.0 V 10% 2 10 A XT1 = VDD, STOP mode When feedback resistor is not used VDD = 5.0 V 10% 0.1 30 A VDD = 3.0 V 10% 0.05 10 A VDD = 2.0 V 10% 0.05 10 A Notes 1. Total current through the internal power supply (VDD0, VDD1) (except the current through pull-up resistors of ports). 2. IDD1 includes the peripheral operation current. 3. When the processor clock control register (PCC) is cleared to 00H. 4. When PCC is set to 02H. 5. When main system clock operation is stopped. 6. Includes the current through the AVDD pin. User's Manual U14046EJ5V0UD 525 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (4/4) (2) PD78F0034A, 78F0034AY, 78F0034BY, 78F0034BY(A) Parameter Symbol Power supply currentNote 1 IDD1Note 2 IDD2 Conditions TYP. MAX. Unit 10.5 21 mA 11.5 23 mA 5.00 MHz VDD = 3.0 V 10%Note 3 When A/D converter is crystal oscillation stopped 4.5 9 mA operating mode 5.5 11 mA VDD = 2.0 V 10%Note 4 When A/D converter is stopped 1 2 mA When A/D converter is operatingNote 6 2 6 mA 1.2 2.4 mA 5 mA 0.8 mA 1.7 mA 0.4 mA 1.1 mA 8.38 MHz VDD = 5.0 V crystal oscillation operating mode 10%Note 3 MIN. When A/D converter is stopped When A/D converter is operatingNote 6 When A/D converter is operatingNote 6 8.38 MHz VDD = 5.0 V 10%Note 3 When peripheral functions crystal oscillation are stopped HALT mode When peripheral functions are operating 5.00 MHz VDD = 3.0 V 10%Note 3 When peripheral functions crystal oscillation are stopped HALT mode 0.4 When peripheral functions are operating VDD = 2.0 V 10%Note 4 When peripheral functions are stopped 0.2 When peripheral functions are operating IDD3 IDD4 IDD5 32.768 kHz crystal oscillation operating modeNote 5 32.768 kHz crystal oscillation HALT modeNote 5 XT1 = VDD, STOP mode When feedback resistor is not used VDD = 5.0 V 10% 115 230 A VDD = 3.0 V 10% 95 190 A VDD = 2.0 V 10% 75 150 A VDD = 5.0 V 10% 30 60 A VDD = 3.0 V 10% 6 18 A VDD = 2.0 V 10% 2 10 A VDD = 5.0 V 10% 0.1 30 A VDD = 3.0 V 10% 0.05 10 A VDD = 2.0 V 10% 0.05 10 A Notes 1. Total current through the internal power supply (VDD0, VDD1) (except the current through pull-up resistors of ports). 2. IDD1 includes the peripheral operation current. 3. When the processor clock control register (PCC) is cleared to 00H. 4. When PCC is set to 02H. 5. When main system clock operation is stopped. 6. Includes the current through the AVDD pin. 526 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) AC Characteristics (1) Basic operation (TA = -40 to +85C, VDD = 1.8 to 5.5 V) Parameter Symbol Cycle time (Min. instruction execution time) TCY Conditions Operating with main system clock MIN. tTIH0, tTIL0 TI50, TI51 input fTI5 frequency TI50, TI51 input high-/low-level width tTIH5, tTIL5 Interrupt request input high-/lowlevel width tINTH, tINTL RESET low-level width tRSL MAX. Unit 4.0 V VDD 5.5 V 0.238 16 s 2.7 V VDD < 4.0 V 0.4 16 s 1.8 V VDD < 2.7 V 1.6 16 s 125 s 103.9Note 1 Operating with subsystem clock TI00, TI01 input high-/low-level width TYP. 122 2/fsam + 0.1Note 2 s 2.7 V VDD < 4.0 V 2/fsam + 0.2Note 2 s 1.8 V VDD < 2.7 V 2/fsam + 0.5Note 2 s 2.7 V VDD 5.5 V 0 4 MHz 1.8 V VDD < 2.7 V 0 275 kHz 2.7 V VDD 5.5 V 100 ns 1.8 V VDD < 2.7 V 1.8 s 2.7 V VDD 5.5 V 1 s 1.8 V VDD < 2.7 V 2 s 2.7 V VDD 5.5 V 10 s 1.8 V VDD < 2.7 V 20 s 4.0 V VDD 5.5 V INTP0 to INTP3, P40 to P47 Notes 1. Value when the external clock is used. When a crystal resonator is used, it is 114 s (MIN.). 2. Selection of fsam = fX, fX/4, fX/64 is possible using bits 0 and 1 (PRM00, PRM01) of prescaler mode register 0 (PRM0). However, if the TI00 valid edge is selected as the count clock, the value becomes fsam = fX/8. User's Manual U14046EJ5V0UD 527 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) TCY vs. VDD (main system clock operation) 16.0 Cycle time TCY [ S] 10.0 5.0 Operation guaranteed range 2.0 1.6 1.0 0.4 0.238 0.1 0 1.0 2.0 1.8 3.0 4.0 2.7 Supply voltage VDD [V] 528 User's Manual U14046EJ5V0UD 5.0 5.5 6.0 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 4.0 to 5.5 V) (1/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 20 ns Address hold time tADH 6 ns Data input time from address tADD1 (2 + 2n)tCY - 54 ns tADD2 (3 + 2n)tCY - 60 ns 100 ns Address output time from RD tRDAD Data input time from RD tRDD1 (2 + 2n)tCY - 87 ns tRDD2 (3 + 2n)tCY - 93 ns 0 Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 33 ns tRDL2 (2.5 + 2n)tCY - 33 ns Input time from RD to WAIT tRDWT1 tCY - 43 ns tRDWT2 tCY - 43 ns Input time from WR to WAIT tWRWT tCY - 25 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 6 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 15 ns Delay time from ASTB to RD tASTRD 6 ns Delay time from ASTB to WR tASTWR 2tCY - 15 ns Delay time from tRDAST 0.8tCY - 15 1.2tCY ns tRDADH 0.8tCY - 15 1.2tCY + 30 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 10 60 ns Address hold time from WR tWRADH 0.8tCY - 15 1.2tCY + 30 ns Delay time from WAIT to RD tWTRD 0.8tCY 2.5tCY + 25 ns Delay time from WAIT to WR tWTWR 0.8tCY 2.5tCY + 25 ns RD to ASTB at external fetch Address hold time from RD at external fetch Remarks ns 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) User's Manual U14046EJ5V0UD 529 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 2.7 to 4.0 V) (2/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 30 ns Address hold time tADH 10 ns Input time from address to data tADD1 (2 + 2n)tCY - 108 ns tADD2 (3 + 2n)tCY - 120 ns 200 ns Output time from RD to address tRDAD 0 Input time from RD to data tRDD1 (2 + 2n)tCY - 148 ns tRDD2 (3 + 2n)tCY - 162 ns Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 40 ns tRDL2 (2.5 + 2n)tCY - 40 ns Input time from RD to WAIT tRDWT1 tCY - 75 ns tRDWT2 tCY - 60 ns Input time from WR to WAIT tWRWT tCY - 50 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 10 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 30 ns Delay time from ASTB to RD tASTRD 10 ns Delay time from ASTB to WR tASTWR 2tCY - 30 ns Delay time from tRDAST 0.8tCY - 30 1.2tCY ns tRDADH 0.8tCY - 30 1.2tCY + 60 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 20 120 ns Hold time from WR to address tWRADH 0.8tCY - 30 1.2tCY + 60 ns Delay time from WAIT to RD tWTRD 0.5tCY 2.5tCY + 50 ns Delay time from WAIT to WR tWTWR 0.5tCY 2.5tCY + 50 ns RD to ASTB at external fetch Hold time from RD to address at external fetch Remarks 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) 530 ns User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (2) Read/write operation (TA = -40 to +85C, VDD = 1.8 to 2.7 V) (3/3) Parameter Symbol Conditions MIN. MAX. Unit ASTB high-level width tASTH 0.3tCY ns Address setup time tADS 120 ns Address hold time tADH 20 ns Input time from address to data tADD1 (2 + 2n)tCY - 233 ns tADD2 (3 + 2n)tCY - 240 ns 400 ns Output time from RD to address tRDAD 0 Input time from RD to data tRDD1 (2 + 2n)tCY - 325 ns tRDD2 (3 + 2n)tCY - 332 ns Read data hold time tRDH 0 ns RD low-level width tRDL1 (1.5 + 2n)tCY - 92 ns tRDL2 (2.5 + 2n)tCY - 92 ns Input time from RD to WAIT tRDWT1 tCY - 350 ns tRDWT2 tCY - 132 ns Input time from WR to WAIT tWRWT tCY - 100 ns WAIT low-level width tWTL (0.5 + 2n)tCY + 10 (2 + 2n)tCY ns Write data setup time tWDS 60 ns Write data hold time tWDH 20 ns WR low-level width tWRL1 (1.5 + 2n)tCY - 60 ns Delay time from ASTB to RD tASTRD 20 ns Delay time from ASTB to WR tASTWR 2tCY - 60 ns Delay time from tRDAST 0.8tCY - 60 1.2tCY ns tRDADH 0.8tCY - 60 1.2tCY + 120 ns Write data output time from RD tRDWD 40 Write data output time from WR tWRWD 40 240 ns Hold time from WR to address tWRADH 0.8tCY - 60 1.2tCY + 120 ns Delay time from WAIT to RD tWTRD 0.5tCY 2.5tCY + 100 ns Delay time from WAIT to WR tWTWR 0.5tCY 2.5tCY + 100 ns RD to ASTB at external fetch Hold time from RD to address at external fetch Remarks ns 1. tCY = TCY/4 2. n indicates the number of waits. 3. CL = 100 pF (CL indicates the load capacitance of the AD0 to AD7, A8 to A15, RD, WR, WAIT, and ASTB pins.) User's Manual U14046EJ5V0UD 531 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (3) Serial interface (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (1/3) (a) 3-wire serial I/O mode (SCK3n... Internal clock output) Parameter SCK3n Symbol tKCY1 cycle time SCK3n high-/ tKH1, tKL1 low-level width SI3n setup time tSIK1 (to SCK3n) SI3n hold time (from SCK3n) tKSI1 Delay time from SCK3n to SO3n output tKSO1 Conditions MIN. TYP. MAX. Unit 4.0 V VDD 5.5 V 954 ns 2.7 V VDD < 4.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns 4.0 V VDD 5.5 V tKCY1/2 - 50 ns 1.8 V VDD < 4.0 V tKCY1/2 - 100 ns 4.0 V VDD 5.5 V 100 ns 2.7 V VDD < 4.0 V 150 ns 1.8 V VDD < 2.7 V 300 ns 400 ns C = 100 pFNote 300 ns MAX. Unit Note C is the load capacitance of the SCK3n and SO3n output lines. (b) 3-wire serial I/O mode (SCK3n... External clock input) Parameter SCK3n Symbol tKCY2 cycle time SCK3n high-/ tKH2, tKL2 low-level width Conditions MIN. TYP. 4.0 V VDD 5.5 V 800 ns 2.7 V VDD < 4.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns 4.0 V VDD 5.5 V 400 ns 2.7 V VDD < 4.0 V 800 ns 1.8 V VDD < 2.7 V 1600 ns SI3n setup time (to SCK3n) tSIK2 100 ns SI3n hold time (from SCK3n) tKSI2 400 ns Delay time from SCK3n to SO3n output tKSO2 C = 100 pF Note 300 Note C is the load capacitance of the SO3n output line. Remark PD780024A, 780034A Subseries: n = 0, 1 PD780024AY, 780034AY Subseries: n = 0 532 User's Manual U14046EJ5V0UD ns CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (3) Serial interface (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (2/3) (c) UART mode (dedicated baud-rate generator output) Parameter Symbol Transfer rate Conditions MIN. TYP. MAX. Unit 4.0 V VDD 5.5 V 131031 bps 2.7 V VDD < 4.0 V 78125 bps 1.8 V VDD < 2.7 V 39063 bps MAX. Unit (d) UART mode (external clock input) Parameter ASCK0 cycle time ASCK0 high-/low-level width Symbol tKCY3 Conditions MIN. TYP. 4.0 V VDD 5.5 V 800 ns 2.7 V VDD < 4.0 V 1600 ns 1.8 V VDD < 2.7 V 3200 ns tKH3, 4.0 V VDD 5.5 V 400 ns tKL3 2.7 V VDD < 4.0 V 800 ns 1.8 V VDD < 2.7 V 1600 Transfer rate ns 4.0 V VDD 5.5 V 39063 bps 2.7 V VDD < 4.0 V 19531 bps 1.8 V VDD < 2.7 V 9766 bps MAX. Unit (e) UART mode (infrared data transfer mode) Parameter Symbol Conditions MIN. Transfer rate 4.0 V VDD 5.5 V 131031 bps Allowable bit rate error 4.0 V VDD 5.5 V 0.87 % Output pulse width 4.0 V VDD 5.5 V 1.2 0.24/fbrNote s Input pulse width 4.0 V VDD 5.5 V 4/fX s Note fbr: Specified baud rate User's Manual U14046EJ5V0UD 533 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) (3) Serial interface (TA = -40 to +85C, VDD = 1.8 to 5.5 V) (3/3) (f) I2C bus mode (PD780024AY, 780034AY Subseries only) Parameter Symbol Standard Mode MIN. MAX. High-Speed Mode MIN. MAX. Unit SCL0 clock frequency fCLK 0 100 0 400 kHZ Bus free time tBUF 4.7 - 1.3 - s Hold timeNote 1 tHD:STA 4.0 - 0.6 - s SCL0 clock low-level width tLOW 4.7 - 1.3 - s SCL0 clock high-level width tHIGH 4.0 - 0.6 - s Start/restart condition setup time tSU:STA 4.7 - 0.6 - s Data hold time CBUS-compatible master tHD:DAT (between stop and start conditions) I2C bus 5.0 - - - s 0Note 2 - 0Note 2 0.9 Note 3 s Data setup time tSU:DAT 250 - 100Note 4 - ns SDA0 and SCL0 signal rise time tR - 1000 20 + 0.1CbNote 5 300 ns SDA0 and SCL0 signal fall time tF - 300 0.1CbNote 5 300 ns Stop condition setup time tSU:STO 4.0 - - s Spike pulse width controlled by input filter tSP - - Capacitive load per bus line Cb - 400 20 + 0.6 0 - 50 ns 400 pF Notes 1. In the start condition, the first clock pulse is generated after this hold time. 2. To fill in the undefined area of the SCL0 falling edge, it is necessary for the device to internally provide at least 300 ns of hold time for the SDA0 signal (which is VIHmin. of the SCL0 signal). 3. If the device does not extend the SCL0 signal low hold time (tLOW), only the maximum data hold time tHD:DAT needs to be fulfilled. 4. The high-speed mode I2C bus is available in a standard mode I2C bus system. At this time, the conditions described below must be satisfied. * If the device does not extend the SCL0 signal low state hold time tSU:DAT 250 ns * If the device extends the SCL0 signal low state hold time Be sure to transmit the next data bit to the SDA0 line before the SCL0 line is released (tRmax. + tSU:DAT = 1000 + 250 = 1250 ns by standard mode I2C bus specification). 5. Cb: Total capacitance per bus line (unit: pF) 534 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) A/D Converter Characteristics (TA = -40 to +85C, VDD = AVDD = 1.8 to 5.5 V, AVSS = VSS = 0 V) (1/2) (1) 8-bit A/D converter: PD780024A, 780024AY Subseries Parameter Symbol Conditions MIN. TYP. MAX. Unit 8 8 8 bit 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR Resolution Overall errorNote Conversion time tCONV Analog input voltage VAIN Reference voltage AVREF Resistance between AVREF and AVSS RREF 4.0 V AVDD 5.5 V 14 96 s 2.7 V AVDD < 4.0 V 19 96 s 1.8 V AVDD < 2.7 V 28 96 s 0 AVREF V 1.8 AVDD V During A/D converter operation 20 40 k Note Excludes quantization error (1/2 LSB). This value is indicated as a ratio (%FSR) to the full-scale value. Remark The impedance of the analog input pins is shown below. [Equivalent circuit] R1 R2 ANIn (n = 0 to 3) C1 C2 C3 [Parameter value] (TYP.) AVDD R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF User's Manual U14046EJ5V0UD 535 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) A/D Converter Characteristics (TA = -40 to +85C, VDD = AVDD = 1.8 to 5.5 V, AVSS = VSS = 0 V) (2/2) (2) 10-bit A/D converter: PD780034A, 780034AY Subseries Parameter Symbol Conditions MIN. TYP. MAX. Unit 10 10 10 bit 4.0 V AVREF 5.5 V 0.2 0.4 %FSR 2.7 V AVREF < 4.0 V 0.3 0.6 %FSR 1.8 V AVREF < 2.7 V 0.6 1.2 %FSR Resolution Overall errorNotes 1, 2 Conversion time Zero-scale Full-scale tCONV errorNotes 1, 2 errorNotes 1, 2 Integral linearity errorNote 1 Differential linearity error Analog input voltage VAIN Reference voltage AVREF Resistance between AVREF and AVSS RREF 4.0 V AVDD 5.5 V 14 96 s 2.7 V AVDD < 4.0 V 19 96 s 1.8 V AVDD < 2.7 V 28 96 s 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR 4.0 V AVREF 5.5 V 0.4 %FSR 2.7 V AVREF < 4.0 V 0.6 %FSR 1.8 V AVREF < 2.7 V 1.2 %FSR 4.0 V AVREF 5.5 V 2.5 LSB 2.7 V AVREF < 4.0 V 4.5 LSB 1.8 V AVREF < 2.7 V 8.5 LSB 4.0 V AVREF 5.5 V 1.5 LSB 2.7 V AVREF < 4.0 V 2.0 LSB 1.8 V AVREF < 2.7 V 3.5 LSB 0 AVREF V 1.8 AVDD V During A/D converter operation 20 40 k Notes 1. Excludes quantization error (1/2 LSB). 2. This value is indicated as a ratio to the full-scale value. Remark The impedance of the analog input pins is shown below. [Equivalent circuit] R1 R2 ANIn (n = 0 to 3) C3 C2 C1 [Parameter value] (TYP.) 536 AVDD R1 R2 C1 C2 C3 2.7 V 12 k 8.0 k 8.0 pF 3.0 pF 2.0 pF 4.5 V 4 k 2.7 k 8.0 pF 1.4 pF 2.0 pF User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Data Memory STOP Mode Low Supply Voltage Data Retention Characteristics (TA = -40 to +85C) Parameter Symbol Data retention power supply voltage VDDDR Data retention power IDDDR supply current Release signal set time Oscillation stabilization wait time Conditions TYP. 1.6 VDDDR = 1.6 V (Subsystem clock unused (XT1 = VDD) and feedback resistor disconnected) tSREL tWAIT MIN. 0.1 MAX. Unit 5.5 V 30 A s 0 Release by RESET 217/fX s Release by interrupt request Note s Note Selection of 212/fX and 214/fX to 217/fX is possible using bits 0 to 2 (OSTS0 to OSTS2) of the oscillation stabilization time select register (OSTS). User's Manual U14046EJ5V0UD 537 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Flash Memory Programming Characteristics (1/3) (TA = +10 to +40C, VDD = AVDD = 2.7 to 5.5 V, VSS = AVSS = 0 V) (1) PD78F0034A, 78F0034AY (a) Write erase characteristics Parameter Symbol Operating frequency fX VPP supply voltage VPP2 VDD supply currentNote 2 IDD Conditions MIN. TYP. MAX. Unit 4.0 V VDD 5.5 V 1.0 8.38 MHz 2.7 V VDD < 4.0 V 1.0 5.0 MHz During flash memory programmingNote 1 9.7 10.3 V 24 mA 12 mA 100 mA 1.01 s 20 s/chip 100 s When step write time = 100 s (1 word = 1 byte) 1000 s 1 erase + 1 write after erase = 1 rewrite 20Note 8 Times/area 10.0 When 8.38 MHz crystal VDD = 5.0 V10% VPP = VPP2 oscillation operating mode 5.0 MHz crystal VDD = 3.0 V10% oscillation operating mode VPP supply current Step erase Overall erase Step write IPP timeNote 3 Ter timeNote 4 timeNote 5 Overall write time per When VPP = VPP2 Tera 0.99 When step erase time = 1 s Twr wordNote 6 Number of rewrites per chipNote 7 Twrw Cerwr 1.0 50 Notes 1. Product rank "K, E, P" indicates 10.2 V (MIN.), 10.3 V (TYP.), and 10.4 V (MAX.). 2. 3. 4. 5. 6. AVDD current and port current (current that flows through the internal pull-up resistor) are not included. The recommended setting value of the step erase time is 1 s. The prewrite time before erasure and the erase verify time are not included. The recommended setting value of the step write time is 50 s. The actual write time per word is 100 s longer. The internal verify time during or after a write is not included. 7. When a product is first written after shipment, "erase write" and "write only" are both taken as one rewrite. Example: P: Write, E: Erase Shipped product PEPEP: 3 rewrites Shipped product EPEPEP: 3 rewrites 8. Product rank "K, E" indicates one time (MAX.). (b) Serial write operation characteristics Parameter Symbol Conditions MIN. TYP. MAX. Unit Set time from VDD to VPP tDP 10 s Release time from VPP to RESET tPR 1.0 s VPP pulse input start time from RESET tRP 1.0 s VPP pulse high-/low-level width tPW 8.0 s VPP pulse input end time from RESET tRPE VPP pulse low-level input voltage VPPL 0.8VDD VPP pulse high-level input voltage VPPH 9.7 538 User's Manual U14046EJ5V0UD 20 ms VDD 1.2VDD V 10.0 10.3 V CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Flash Memory Programming Characteristics (2/3) (TA = +10 to +40C, VDD = AVDD = 1.8 to 5.5 V, VSS = AVSS = 0 V) (2) PD78F0034BY, 78F0034BY(A) (a) Write erase characteristics Parameter Symbol Operating frequency fX VPP supply voltage VDD supply current VPP2 Note 1 IDD VPP supply current Step erase time Overall erase time Writeback time IPP Note 2 Tera Cwb Number of erases/writebacks Cerwb Note 6 Overall write time per word Number of rewrites per chip Note 8 MAX. Unit 8.38 MHz 2.7 V VDD < 4.0 V 1.0 5.0 MHz 1.8 V VDD < 2.7 V 1.0 1.25 MHz During flash memory programming 9.7 10.3 V 24 mA 17 mA 100 mA 0.201 s 20 s/chip 10.0 When 8.38 MHz crystal VDD = 5.0 V10% VPP = VPP2 oscillation VDD = 3.0 V10% operating mode When VPP = VPP2 0.199 0.2 When step erase time = 0.2 s 49.4 50 When writeback time = 50 ms Twr Note 7 TYP. 1.0 Twb Number of writebacks per Note 5 writeback command MIN. 4.0 V VDD 5.5 V Ter Note 3 Note 4 Step write time Conditions 48 Twrw When step write time = 50 s (1 word = 1 byte) Cerwr 1 erase + 1 write after erase = 1 rewrite 48 50 50.6 ms 60 Times 16 Times 52 s 520 s 20 Times/area Notes 1. 2. 3. 4. 5. AVDD current and port current (current that flows through the internal pull-up resistor) are not included. The recommended setting value of the step erase time is 0.2 s. The prewrite time before erasure and the erase verify time (writeback time) are not included. The recommended setting value of the writeback time is 50 ms. Writeback is executed once by the issuance of the writeback command. Therefore, the number of retries must be the maximum value minus the number of commands issued. 6. The recommended setting value of the step write time is 50 s. 7. The actual write time per word is 100 s longer. The internal verify time during or after a write is not included. 8. When a product is first written after shipment, "erase write" and "write only" are both taken as one rewrite. Example: P: Write, E: Erase Shipped product PEPEP: 3 rewrites Shipped product EPEPEP: 3 rewrites User's Manual U14046EJ5V0UD 539 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Flash Memory Programming Characteristics (3/3) (TA = +10 to +40C, VDD = AVDD = 1.8 to 5.5 V, VSS = AVSS = 0 V) (b) Serial write operation characteristics Parameter Symbol Conditions MIN. TYP. MAX. Unit Set time from VDD to VPP tDP 10 s Release time from VPP to RESET tPR 1.0 s VPP pulse input start time from RESET tRP 1.0 s VPP pulse high-/low-level width tPW 8.0 s VPP pulse input end time from RESET tRPE VPP pulse low-level input voltage VPPL 0.8VDD VPP pulse high-level input voltage VPPH 9.7 540 User's Manual U14046EJ5V0UD 10.0 20 ms 1.2VDD V 10.3 V CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Timing Charts AC Timing Test Points (excluding X1, XT1 input) 0.8VDD 0.2VDD 0.8VDD Test points 0.2VDD Clock Timing 1/fX tXL tXH VIH4 (MIN.) VIL4 (MAX.) X1 input 1/fXT tXTL tXTH VIH5 (MIN.) VIL5 (MAX.) XT1 input TI Timing tTIL0 tTIH0 TI00, TI01 1/fTI5 tTIL5 tTIH5 TI50, TI51 User's Manual U14046EJ5V0UD 541 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Interrupt Request Input Timing tINTL tINTH INTP0 to INTP3 RESET Input Timing tRSL RESET 542 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Read/Write Operation External fetch (no wait): A8 to A15 Higher 8-bit address tADD1 AD0 to AD7 Hi-Z Lower 8-bit address tADS Instruction code tRDAD tRDD1 tADH tRDADH tASTH tRDAST ASTB RD tASTRD tRDL1 tRDH External fetch (wait insertion): A8 to A15 Higher 8-bit address tADD1 AD0 to AD7 Hi-Z Lower 8-bit address tADS tADH tRDAD Instruction code tRDADH tRDD1 tASTH tRDAST ASTB RD tASTRD tRDL1 tRDH WAIT tRDWT1 tWTL User's Manual U14046EJ5V0UD tWTRD 543 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) External data access (no wait): A8 to A15 Higher 8-bit address tADD2 AD0 to AD7 Hi-Z tRDAD tRDD2 Lower 8-bit address tADS tADH tASTH Hi-Z Write data Read data tRDH ASTB RD tASTRD tRDWD tRDL2 tWDS tWDH tWRADH tWRWD WR tASTWR tWRL1 External data access (wait insertion): A8 to A15 Higher 8-bit address tADD2 AD0 to AD7 Lower 8-bit address tADS tADH tASTH Hi-Z Read data Hi-Z Write data tRDAD tRDH tRDD2 ASTB tASTRD RD tRDWD tRDL2 tWDH tWDS tWRWD WR tASTWR tWRL1 tWRADH WAIT tRDWT2 tWTL tWTRD tWTL tWRWT 544 User's Manual U14046EJ5V0UD tWTWR CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Serial Transfer Timing 3-wire serial I/O mode: tKCYm tKLm tKHm SCK3n tSIKm tKSIm Input data SI3n tKSOm SO3n Output data Remarks 1. m = 1, 2 2. PD780024A, 780034A Subseries: n = 0, 1 PD780024AY, 780034AY Subseries: n = 0 UART mode (external clock input): t KCY3 t KL3 t KH3 ASCK0 I2C bus mode (PD780024AY, 780034AY Subseries only): tLOW tR SCL0 tHD:DAT tHD:STA tHIGH tSU:DAT tF tSU:STA tHD:STA tSP tSU:STO SDA0 tBUF Stop condition Start condition Restart condition User's Manual U14046EJ5V0UD Stop condition 545 CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Data Retention Timing (STOP Mode Release by RESET) Internal reset operation HALT mode Operating mode STOP mode Data retention mode VDD VDDDR tSREL STOP instruction execution RESET tWAIT Data Retention Timing (Standby Release Signal: STOP Mode Release by Interrupt Request Signal) HALT mode Operating mode STOP mode Data retention mode VDD VDDDR tSREL STOP instruction execution Standby release signal (interrupt request) tWAIT 546 User's Manual U14046EJ5V0UD CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) Flash Memory Write Mode Set Timing VDD VDD 0V tDP tRP tPW VPPH VPP VPPL tPW 0V tPR tRPE VDD RESET (input) 0V User's Manual U14046EJ5V0UD 547 CHAPTER 27 PACKAGE DRAWINGS 64-PIN PLASTIC SDIP (19.05mm(750)) 64 33 1 32 A K J L I M F D N C M R B H G NOTES 1. Each lead centerline is located within 0.17 mm of its true position (T.P.) at maximum material condition. 2. Item "K" to center of leads when formed parallel. ITEM MILLIMETERS A 58.0+0.68 -0.20 B 1.78 MAX. C 1.778 (T.P.) D 0.500.10 F 0.9 MIN. G 3.20.3 H 0.51 MIN. I 4.05+0.26 -0.20 J 5.08 MAX. K 19.05 (T.P.) L 17.00.2 M 0.25+0.10 -0.05 N 0.17 R 0 ~ 15 P64C-70-750A,C-4 Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. 548 User's Manual U14046EJ5V0UD CHAPTER 27 PACKAGE DRAWINGS 64-PIN PLASTIC QFP (14x14) A B detail of lead end 33 32 48 49 S C D Q 64 1 R 17 16 F J G H I M P K S N S L M NOTE ITEM Each lead centerline is located within 0.15 mm of its true position (T.P.) at maximum material condition. MILLIMETERS A 17.60.4 B 14.00.2 C 14.00.2 D 17.60.4 F 1.0 G 1.0 H 0.37 +0.08 -0.07 I J 0.15 0.8 (T.P.) K 1.80.2 L 0.80.2 M 0.17 +0.08 -0.07 N 0.10 P 2.550.1 Q 0.10.1 R 5 5 S 2.85 MAX. P64GC-80-AB8-5 Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. User's Manual U14046EJ5V0UD 549 CHAPTER 27 PACKAGE DRAWINGS 64-PIN PLASTIC LQFP (14x14) A B 48 49 33 32 detail of lead end S P C D T R 64 1 L 17 16 U Q F G J H I M ITEM K S N M S MILLIMETERS A 17.20.2 B 14.00.2 C 14.00.2 D 17.20.2 F 1.0 G 1.0 H 0.37 +0.08 -0.07 I 0.20 J K 0.8 (T.P.) NOTE L 0.8 Each lead centerline is located within 0.20 mm of its true position (T.P.) at maximum material condition. M 0.17 +0.03 -0.06 N 0.10 P 1.40.1 Q 0.1270.075 +4 3 -3 R S T U 1.60.2 1.7 MAX. 0.25 0.8860.15 P64GC-80-8BS Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. 550 User's Manual U14046EJ5V0UD CHAPTER 27 PACKAGE DRAWINGS 64-PIN PLASTIC TQFP (12x12) A B 48 detail of lead end 33 32 49 S P T C D R L U 64 Q 17 16 1 F G J H I M ITEM K S M N S NOTE Each lead centerline is located within 0.13 mm of its true position (T.P.) at maximum material condition. MILLIMETERS A B 14.00.2 12.00.2 C 12.00.2 D F 14.00.2 1.125 G 1.125 H 0.32 +0.06 -0.10 I 0.13 J 0.65 (T.P.) K 1.00.2 L 0.5 M 0.17 +0.03 -0.07 N 0.10 P 1.0 Q 0.10.05 R 3 +4 -3 S 1.10.1 T 0.25 U 0.60.15 P64GK-65-9ET-3 Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. User's Manual U14046EJ5V0UD 551 CHAPTER 27 PACKAGE DRAWINGS 64-PIN PLASTIC LQFP (10x10) A B 48 detail of lead end 33 32 49 S P C T D R 64 U 17 Q 16 1 L F G J H I M ITEM A K B S N S M MILLIMETERS 12.00.2 10.00.2 C 10.00.2 D 12.00.2 F 1.25 G 1.25 H 0.220.05 I 0.08 J 0.5 (T.P.) NOTE K 1.00.2 Each lead centerline is located within 0.08 mm of its true position (T.P.) at maximum material condition. L 0.5 M 0.17 +0.03 -0.07 N 0.08 P 1.4 Q 0.10.05 R 3 +4 -3 S 1.50.10 T 0.25 U 0.60.15 S64GB-50-8EU-2 Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. 552 User's Manual U14046EJ5V0UD CHAPTER 27 PACKAGE DRAWINGS 73-PIN PLASTIC FBGA (9x9) D w S A ZE ZD A 9 8 7 6 5 4 3 2 1 B E J H G F E D C B A w S B INDEX MARK A y1 A2 S (UNIT:mm) S y S e b A1 x M S AB ITEM D DIMENSIONS 9.000.10 E 9.000.10 w 0.20 A 1.280.10 A1 0.350.06 A2 0.93 e 0.80 b 0.50 +0.05 -0.10 x 0.08 y 0.10 y1 0.20 ZD 1.30 ZE 1.30 P73F1-80-CN3 Remark The external dimensions and materials of the ES version are the same as those of the mass-produced version. User's Manual U14046EJ5V0UD 553 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. For soldering methods and conditions other than those recommended below, contact an NEC Electronics sales representative. For technical information, see the following website. Semiconductor Device Mount Manual (http://www.necel.com/pkg/en/mount/index.html) Caution Evaluation of the soldering conditions for the products under development and being planned is incomplete. Table 28-1. Surface Mounting Type Soldering Conditions (1/7) (1) 64-pin plastic QFP (14 x 14) PD780021AGC-xxx-AB8, 780022AGC-xxx-AB8, 780023AGC-xxx-AB8, PD780024AGC-xxx-AB8, 780021AYGC-xxx-AB8, 780022AYGC-xxx-AB8, PD780023AYGC-xxx-AB8, 780024AYGC-xxx-AB8, 780031AGC-xxx-AB8, PD780032AGC-xxx-AB8, 780033AGC-xxx-AB8, 780034AGC-xxx-AB8, PD780031AYGC-xxx-AB8, 780032AYGC-xxx-AB8, 780033AYGC-xxx-AB8, PD780034AYGC-xxx-AB8, 780021AGC(A)-xxx-AB8, 780022AGC(A)-xxx-AB8, PD780023AGC(A)-xxx-AB8, 780024AGC(A)-xxx-AB8, 780022AYGC(A)-xxx-AB8, PD780031AGC(A)-xxx-AB8, 780032AGC(A)-xxx-AB8, 780033AGC(A)-xxx-AB8, PD780034AGC(A)-xxx-AB8 Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 235C, Time: 30 seconds max. (at 210C or higher), Count: Three times or less IR35-00-3 VPS Package peak temperature: 215C, Time: 40 seconds max. (at 200C or higher), Count: Three times or less VP15-00-3 Wave soldering Solder bath temperature: 260C max., Time: 10 seconds max., Count: Once, Preheating temperature: 120C max. (package surface WS60-00-1 temperature) Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) Caution Do not use different soldering methods together (except for partial heating). 554 User's Manual U14046EJ5V0UD - CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (2/7) (2) 64-pin plastic LQFP (14 x 14) PD780021AGC-xxx-8BS, 780022AGC-xxx-8BS, 780023AGC-xxx-8BS, PD780024AGC-xxx-8BS, 780021AYGC-xxx-8BS, 780022AYGC-xxx-8BS, PD780023AYGC-xxx-8BS, 780024AYGC-xxx-8BS, 780031AGC-xxx-8BS, PD780032AGC-xxx-8BS, 780033AGC-xxx-8BS, 780034AGC-xxx-8BS, PD780031AYGC-xxx-8BS, 780032AYGC-xxx-8BS, 780033AYGC-xxx-8BS, PD780034AYGC-xxx-8BS, 780021AGC(A)-xxx-8BS, 780022AGC(A)-xxx-8BS, PD780023AGC(A)-xxx-8BS, 780024AGC(A)-xxx-8BS, 780031AGC(A)-xxx-8BS, PD780032AGC(A)-xxx-8BS, 780033AGC(A)-xxx-8BS, 780034AGC(A)-xxx-8BS, PD78F0034AGC-8BS, 78F0034AYGC-8BS, 78F0034BGC-8BS, PD78F0034BYGC-8BS, 78F0034BGC(A)-8BS, 78F0034BYGC(A)-8BS 64-pin plastic QFP (14 x 14) PD78F0034AGC-AB8Note, 78F0034AYGC-AB8 Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 235C, Time: 30 seconds max. (at 210C or higher), Count: Two times or less IR35-00-2 VPS Package peak temperature: 215C, Time: 40 seconds max. VP15-00-2 (at 200C or higher), Count: Two times or less Wave soldering Solder bath temperature: 260C max., Time: 10 seconds max., Count: Once, Preheating temperature: 120C max. (package surface temperature) Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) WS60-00-1 - Note Maintenance product Caution Do not use different soldering methods together (except for partial heating). User's Manual U14046EJ5V0UD 555 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (3/7) (3) 64-pin plastic TQFP (12 x 12) PD780021AGK-xxx-9ET, 780022AGK-xxx-9ET, 780023AGK-xxx-9ET, PD780024AGK-xxx-9ET, 780021AYGK-xxx-9ET, 780022AYGK-xxx-9ET, PD780023AYGK-xxx-9ET, 780024AYGK-xxx-9ET, 780031AGK-xxx-9ET, PD780032AGK-xxx-9ET, 780033AGK-xxx-9ET, 780034AGK-xxx-9ET, PD780031AYGK-xxx-9ET, 780032AYGK-xxx-9ET, 780033AYGK-xxx-9ET, PD780034AYGK-xxx-9ET, 780021AGK(A)-xxx-9ET, 780022AGK(A)-xxx-9ET, PD780023AGK(A)-xxx-9ET, 780024AGK(A)-xxx-9ET, 780031AGK(A)-xxx-9ET, PD780032AGK(A)-xxx-9ET, 780033AGK(A)-xxx-9ET, 780034AGK(A)-xxx-9ET, PD78F0034AGK-9ET, 78F0034AYGK-9ET, 78F0034BGK-9ET, 78F0034BYGK-9ET, PD78F0034BGK(A)-9ET, 78F0034BYGK(A)-9ET Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 235C, Time: 30 seconds max. (at 210C or higher), Count: Two times or less, Exposure limit: 7 daysNote (after that, prebake at 125C for 10 hours) IR35-107-2 VPS Package peak temperature: 215C, Time: 40 seconds max. (at 200C or higher), Count: Two times or less, Exposure limit: 7 daysNote (after that, prebake at 125C for 10 hours) VP15-107-2 Wave soldering Solder bath temperature: 260C max., Time: 10 seconds max., Count: Once, Preheating temperature: 120C max. (package surface temperature), Exposure limit: 7 daysNote (after that, prebake at 125C for 10 hours) WS60-107-1 Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) - Note After opening the dry pack, store it at 25C or less and 65% RH or less for the allowable storage period. Caution Do not use different soldering methods together (except for partial heating). 556 User's Manual U14046EJ5V0UD CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (4/7) (4) 64-pin plastic LQFP (10 x 10) PD780021AGB-xxx-8EU, 780022AGB-xxx-8EU, 780023AGB-xxx-8EU, PD780024AGB-xxx-8EU, 780021AYGB-xxx-8EU, 780022AYGB-xxx-8EU, PD780023AYGB-xxx-8EU, 780024AYGB-xxx-8EU, 780031AGB-xxx-8EU, PD780032AGB-xxx-8EU, 780033AGB-xxx-8EU, 780034AGB-xxx-8EU, PD780031AYGB-xxx-8EU, 780032AYGB-xxx-8EU, 780033AYGB-xxx-8EU, PD780034AYGB-xxx-8EU Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 235C, Time: 30 seconds max. (at 210C or higher), Count: Two times or less IR35-00-2 VPS Package peak temperature: 215C, Time: 40 seconds max. (at 200C or higher), Count: Two times or less VP15-00-2 Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) - Caution Do not use different soldering methods together (except for partial heating). (5) 64-pin plastic LQFP (10 x 10) PD78F0034AGB-8EU, 78F0034AYGB-8EU, 78F0034BGB-8EU, 78F0034BYGB-8EU, PD78F0034BGB(A)-8EU, 78F0034BYGB(A)-8EU Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 235C, Time: 30 seconds max. (at 210C or higher), Count: Two times or less, Exposure limit: 7 daysNote (after that prebake at 125C for 10 hours) IR35-107-2 VPS Package peak temperature: 215C, Time: 40 seconds max. (at 200C or higher), Count: Two times or less, Exposure limit: 7 daysNote (after that, prebake at 125C for 10 hours) VP15-107-2 Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) - Note After opening the dry pack, store it at 25C or less and 65% RH or less for the allowable storage period. Caution Do not use different soldering methods together (except for partial heating). User's Manual U14046EJ5V0UD 557 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (5/7) (6) 73-pin plastic FBGA (9 x 9) PD780021AF1-xxx-CN3, 780022AF1-xxx-CN3, 780023AF1-xxx-CN3, PD780024AF1-xxx-CN3, 780021AYF1-xxx-CN3, 780022AYF1-xxx-CN3, PD780023AYF1-xxx-CN3, 780024AYF1-xxx-CN3, 780031AF1-xxx-CN3, PD780032AF1-xxx-CN3, 780033AF1-xxx-CN3, 780034AF1-xxx-CN3, PD780031AYF1-xxx-CN3, 780032AYF1-xxx-CN3, 780033AYF1-xxx-CN3, PD780034AF1-xxx-CN3, 78F0034BF1-CN3, 78F0034BYF1-CN3 Soldering Method Infrared reflow VPS Soldering Conditions Package peak temperature: 260C, Time: 60 seconds max. (at 220C or higher), Count: Three times or less, Exposure limit: 3 daysNote (after that, prebake at 125C for 20 hours) Package peak temperature: 215C, Time: 40 seconds max. (at 200C or higher), Count: Three times or less, Exposure limit: Recommended Condition Symbol IR60-203-3 VP15-203-3 3 daysNote (after that, prebake at 125C for 20 hours) Note After opening the dry pack, store it at 25C or less and 65% RH or less for the allowable storage period. Caution Do not use different soldering methods together. 558 User's Manual U14046EJ5V0UD CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (6/7) (7) 64-pin plastic LQFP (14 x 14) PD780021AGC-xxx-8BS-A, 780022AGC-xxx-8BS-A, 780023AGC-xxx-8BS-A, PD780024AGC-xxx-8BS-A, 780031AGC-xxx-8BS-A, 780032AGC-xxx-8BS-A, PD780033AGC-xxx-8BS-A, 780034AGC-xxx-8BS-A, 78F0034AGC-8BS-A, PD780031AYGC-xxx-8BS-A, 780032AYGC-xxx-8BS-A, 780033AYGC-xxx-8BS-A, PD780034AYGC-xxx-8BS-A, 78F0034BGC-8BS-A, 78F0034BYGC-8BS-A 64-pin plastic TQFP (12 x 12) PD780021AGK-xxx-9ET-A, 780022AGK-xxx-9ET-A, 780023AGK-xxx-9ET-A, PD780024AGK-xxx-9ET-A, 780032AGK-xxx-9ET-A, 780033AGK-xxx-9ET-A, PD780034AGK-xxx-9ET-A, 780022AYGK-xxx-9ET-A, 780023AYGK-xxx-9ET-A, PD780024AYGK-xxx-9ET-A, 780032AYGK-xxx-9ET-A, 780034AYGK-xxx-9ET-A PD78F0034AGK-9ET-A, 78F0034BGK-9ET-A Soldering Method Soldering Conditions Recommended Condition Symbol Infrared reflow Package peak temperature: 260C, Time: 60 seconds max. (at 220C or higher), Count: Three times or less, IR-60-207-3 Exposure limit: 7 daysNotes (after that, prebake at 125C for 20 hours) Wave soldering Conditions are determined individually. For details, consult with an NEC sales representative. - Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) - Note After opening the dry pack, store it at 25C or less and 65% RH or less for the allowable storage period. Caution Do not use different soldering methods together (except for partial heating). Remark Products with -A at the end of the part number are lead-free products. User's Manual U14046EJ5V0UD 559 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Table 28-1. Surface Mounting Type Soldering Conditions (7/7) (8) 64-pin plastic LQFP (10 x 10) PD780021AGB-xxx-8EU-A, 780022AGB-xxx-8EU-A, 780023AGB-xxx-8EU-A, PD780024AGB-xxx-8EU-A, 780031AGB-xxx-8EU-A, 780032AGB-xxx-8EU-A, PD780033AGB-xxx-8EU-A, 780034AGB-xxx-8EU-A, 780021AYGB-xxx-8EU-A, PD780022AYGB-xxx-8EU-A, 780023AYGB-xxx-8EU-A, 780024AYGB-xxx-8EU-A, PD780031AYGB-xxx-8EU-A, 780032AYGB-xxx-8EU-A, 780033AYGB-xxx-8EU-A, PD780034AYGB-xxx-8EU-A, 78F0034AGB-8EU-A, 78F0034BGB-8EU-A, PD78F0034AYGB-8EU-A, 78F0034BYGB-8EU-A Soldering Method Soldering Conditions Infrared reflow Package peak temperature: 260C, Time: 60 seconds max. (at 220C or higher), Count: Three times or less, Exposure limit: 7 daysNote (after that, prebake at 125C for 20 hours) Partial heating Pin temperature: 350C max., Time: 3 seconds max. (per pin row) Recommended Condition Symbol IR-60-207-3 - Note After opening the dry pack, store it at 25C or less and 65% RH or less for the allowable storage period. Remark Products with -A at the end of the part number are lead-free products. Table 28-2. Insertion Type Soldering Conditions 64-pin plastic SDIP (19.05 mm (750)) PD780021ACW-xxx, 780022ACW-xxx, 780023ACW-xxx, 780024ACW-xxx, PD780021AYCW-xxx, 780022AYCW-xxx, 780023AYCW-xxx, 780024AYCW-xxx, PD780031ACW-xxx, 780032ACW-xxx, 780033ACW-xxx, 780034ACW-xxx, PD780031AYCW-xxx, 780032AYCW-xxx, 780033AYCW-xxx, 780034AYCW-xxx, PD780021ACW(A)-xxx, 780022ACW(A)-xxx, 780023ACW(A)-xxx, 780024ACW(A)-xxx, PD780031ACW(A)-xxx, 780032ACW(A)-xxx, 780033ACW(A)-xxx, 780034ACW(A)-xxx, PD78F0034ACW, 78F0034AYCW Soldering Method Wave soldering Soldering Conditions Solder bath temperature: 260C max., Time: 10 seconds max. (only for pins) Partial heating Pin temperature: 300C max., Time: 3 seconds max. (per pin row) Caution Apply wave soldering only to the pins and be careful not to bring solder into direct contact with the package. 560 User's Manual U14046EJ5V0UD APPENDIX A DIFFERENCES BETWEEN PD78018F, 780024A, 780034A, AND 780078 SUBSERIES Tables A-1 and A-2 show the major differences between the PD78018F, 780024A, 780034A, and 780078 Subseries. Table A-1. Major Differences Between PD78018F, 780024A, 780034A, and 780078 Subseries (Hardware) Name PD78018F SubseriesNote PD780024A, 780034A Item PD780078 Subseries Subseries EMI noise reduction Not provided Provided bus version Internal (Y subseries) Provided Provided (multi-task supported) Flash memory version PD78F018F PD78F0034A, 78F0034B PD78F0078 ROM 8 KB to 60 KB 8 KB to 32 KB 48 KB, 60 KB Internal high-speed RAM 512, 1024 bytes 512, 1024 bytes 1024 bytes Internal expansion RAM 512, 1024 bytes Not provided 1024 bytes Minimum instruction execution 0.4 s (10 MHz) 0.24 s (8.38 MHz), 0.16 s (12 MHz, expanded-specification products only) Number of I/O ports 53 51 52 Timer 16 bits: 1, 8 bits: 2, Watch timer: 1, 16 bits: 1, 8 bits: 2, Watch timer: 1, 16 bits: 2, 8 bits: 2, Watch timer: 1, Watchdog timer: 1 Watchdog timer: 1 Watchdog timer: 1 8 bits x 8 * 8 bits x 8 (PD780024A Subseries) * 10 bits x 8 (PD780034A Subseries) 10 bits x 8 Subseries without suffix Y 3-wire/2-wire/SBI: 1, 3-wire (automatic transmission/reception): 1 3-wire: 2, UART: 1 3-wire: 1, UART: 1, 3-wire/UART: 1 Subseries with suffix Y 3-wire/2-wire/I2C: 1, 3-wire (automatic transmission/reception): 1 3-wire: 2, UART: 1, Multi-master I2C: 1 3-wire: 1, UART: 1, 3-wire/UART: 1, Multi-master I2C: 1 I 2C time A/D converter Serial interface Timer output 3 (14-bit PWM output possible: 2) 3 (8-bit PWM output possible: 2) 4 (8-bit PWM output possible: 2) Package * 64-pin SDIP (19.05 mm (750)) * 64-pin SDIP (19.05 mm (750)) * 64-pin QFP (14 x 14) * 64-pin QFP (14 x 14) * 64-pin QFP (14 x 14) * 64-pin TQFP (12 x 12) * 64-pin LQFP (12 x 12) * 64-pin TQFP (12 x 12) * 64-pin LQFP (14 x 14) * 64-pin LQFP (14 x 14) * 64-pin LQFP (10 x 10) * 73-pin FBGA (9 x 9) Device file DF78014 DF780034 DF780078 Emulation board IE-78014-R-EM-A, IE-78018-NS-EM1 IE-780034-NS-EM1 IE-780078-NS-EM1 Electrical specifications Recommended soldering conditions Refer to the data sheet or user's manual (with electrical specifications) of each product. Note Maintenance product User's Manual U14046EJ5V0UD 561 APPENDIX A DIFFERENCES BETWEEN PD78018F, 780024A, 780034A, AND 780078 SUBSERIES Table A-2. Major Differences Between PD78018F, 780024A, 780034A, and 780078 Subseries (Software) (1/2) Name PD78018F SubseriesNote 1 PD780024A, 780034A Item PD780078 Subseries Subseries - A/D converter Take the appropriate measures for the first A/D conversion result immediately after the A/D conversion operation is started (ADCS0 is set to 1), such as discarding it, because it may not satisfy the rating. However, if a wait time of 14 s (MIN.) has been secured after ADCE0 was set to 1 before starting operation (ADCS0 is set to 1), the first data can be used. 16-bit timer/event counter 1 ch 1 ch 2 ch TM0 TM0 TM00 - Interval timer PWM output PPG output Pulse width measurement External event counter Square wave output - - Count clock fX/2, fX/22, fX/23, TI0 fX, fX/22, fX/26, TI00 fX, fX/22, fX/26, TI000 fX/2, fX/23 fX/29, TI001 Control register Output control register Compare/capture register Prescaler mode register Capture/compare control register TMC0 TOC0 CR00, CR01 (Capture only) TCL0Note 2 - TMC0 TOC0 CR00, CR01 PRM0 CRC0 TMC00 TOC00 CR000, CR010 PRM00 CRC00 TMC01 TOC01 CR001, CR011 PRM01 CRC01 Interrupt INTTM0 INTTM00, INTTM01 INTTM000, INTTM010 INTTM001, INTTM011 Notes 1. Maintenance product 2. TCL0: Timer clock select register 0 562 TM01 User's Manual U14046EJ5V0UD APPENDIX A DIFFERENCES BETWEEN PD78018F, 780024A, 780034A, AND 780078 SUBSERIES Table A-2. Major Differences Between PD78018F, 780024A, 780034A, and 780078 Subseries (Software) (2/2) Name PD78018F SubseriesNote PD780024A, 780034A Item 8-bit timer/event counter PD780078 Subseries Subseries 2 ch 2 ch TM1 TM2 TM50 TM51 Unit mode Interval timer External event counter Square wave output PWM output - Cascade connection mode Interval timer External event counter Square wave output Count clock fX/22, fX/23, fX/24, fX/25, fX/26, fX/27, fX/28, fX/29, fX/210,fX212, TI1 Control register Output control register Clock select register TMC1 TOC1 TCL1 Interrupt INTTM1 fX/22, fX/23, fX/24, fX/25, fX/26, fX/27, fX/28, fX/29, fX/210, fX/212, TI2 INTTM2 fX, fX/22, fX/24, fX/26, fX/28, fX/210, TI50 fX/211, TI51 TMC50 TMC50 TCL50 TMC51 TMC51 TCL51 INTTM50 INTTM51 fX/2, fX/23, fX/25, fX/27, fX/29, Note Maintenance product User's Manual U14046EJ5V0UD 563 APPENDIX B DEVELOPMENT TOOLS The following development tools are available for the development of systems that employ the PD780024A, 780034A, 780024AY, and 780034AY Subseries. Figure B-1 shows the development tool configuration. * Support for PC98-NX series Unless otherwise specified, products compatible with IBM PC/ATTM computers are compatible with PC98-NX series computers. When using PC98-NX series computers, refer to the explanation for IBM PC/AT computers. * WindowsTM Unless otherwise specified, "Windows" means the following OSs. * Windows 3.1 * Windows 95 * Windows 98 * Windows 2000 * Windows XP * Windows NTTM Ver 4.0 564 User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS Figure B-1. Development Tool Configuration (1/2) (1) When using the in-circuit emulator IE-78K0-NS, IE-78K0-NS-A Software package * Software package Debugging software Language processing software * Assembler package * Integrated debugger * C compiler package * System simulator * Device file * C library source fileNote 1 Control software * Project manager (Windows only)Note 2 Embedded software * Real-time OS Host machine (PC or EWS) Interface adapter, PC card interface, etc. Power supply unit Flash memory write environment In-circuit emulator Emulation board Flash programmer Flash memory write adapter I/O board Performance board Flash memory Emulation probe Conversion socket or conversion adapter Target system Notes 1. The C library source file is not included in the software package. 2. The project manager is included in the assembler package. The project manager is only used for Windows. User's Manual U14046EJ5V0UD 565 APPENDIX B DEVELOPMENT TOOLS Figure B-1. Development Tool Configuration (2/2) (2) When using the in-circuit emulator IE-78001-R-A Software package * Software package Debugging software Language processing software * Assembler package * Integrated debugger * C compiler package * System simulator * Device file * C library source fileNote 1 Control software * Project manager (Windows only)Note 2 Embedded software * Real-time OS Host machine (PC or EWS) Interface adapter, PC card interface, etc. In-circuit emulator Flash memory write environment Emulation board Flash programmer Emulation probe conversion board Flash memory write adapter I/O board Flash memory Performance board Emulation probe Conversion socket or conversion adapter Target system Notes 1. The C library source file is not included in the software package. 2. The project manager is included in the assembler package. The project manager is only used for Windows. 566 User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS B.1 Software Package SP78K0 Software package This package contains various software tools for 78K/0 Series development. The following tools are included. RA78K0, CC78K0, ID78K0-NS, SM78K0, and various device files Part Number: SxxxxSP78K0 Remark xxxx in the part number differs depending on the OS used. SxxxxSP78K0 xxxx Host Machine OS AB17 PC-9800 series, Windows (Japanese version) BB17 IBM PC/AT compatibles Windows (English version) Supply Medium CD-ROM B.2 Language Processing Software RA78K0 Assembler package This assembler converts programs written in mnemonics into object codes executable with a microcontroller. Further, this assembler is provided with functions capable of automatically creating symbol tables and branch instruction optimization. This assembler should be used in combination with device file (DF780024 or DF780034) (sold separately). <Precaution when using RA78K0 in PC environment> This assembler package is a DOS-based application. It can also be used in Windows, however, by using the project manager (included in the assembler package) on Windows. Part Number: SxxxxRA78K0 CC78K0 C compiler package This compiler converts programs written in C language into object codes executable with a microcontroller. This compiler should be used in combination with an assembler package and device file (both sold separately). <Precaution when using CC78K0 in PC environment> This C compiler package is a DOS-based application. It can also be used in Windows, however, by using the project manager (included in the assembler package) on Windows. Part Number: SxxxxCC78K0 DF780024Note 1 DF780034Note 1 Device file This file contains information peculiar to the device. This device file should be used in combination with tool (RA78K0, CC78K0, SM78K0, ID78K0-NS, and RX78K0) (all sold separately). The corresponding OS and host machine differ depending on the tool used. * DF780024: PD780024A, 780024AY, 780024AS Subseries * DF780034: PD780034A, 780034AY, 780034AS Subseries Part Number: SxxxxDF780024, SxxxxDF780034 CC78K0-LNote 2 C library source file This is a source file of functions configuring the object library included in the C compiler package. This file is required to match the object library included in C compiler package to the user's specifications. It does not depend on the operating environment because it is a source file. Part Number: SxxxxCC78K0-L User's Manual U14046EJ5V0UD 567 APPENDIX B DEVELOPMENT TOOLS Notes 1. The DF780024 and DF780034 can be used in common with the RA78K0, CC78K0, SM78K0, ID78K0NS, and RX78K0. 2. CC78K0-L is not included in the software package (SP78K0). Remark xxxx in the part number differs depending on the host machine and OS used. SxxxxRA78K0 SxxxxCC78K0 xxxx Host Machine OS AB13 PC-9800 series, Windows (Japanese version) BB13 IBM PC/AT compatibles Windows (English version) AB17 Windows (Japanese version) BB17 Windows (English version) 3P17 HP9000 series 700TM HP-UXTM (Rel. 10.10) 3K17 SPARCstationTM SunOSTM (Rel. 4.1.4), SolarisTM (Rel. 2.5.1) Supply Medium 3.5-inch 2HD FD CD-ROM SxxxxDF780024 SxxxxDF780034 SxxxxCC78K0-L xxxx Host Machine OS Supply Medium AB13 PC-9800 series, Windows (Japanese version) BB13 IBM PC/AT compatibles Windows (English version) 3P16 HP9000 series 700 HP-UX (Rel. 10.10) DAT 3K13 SPARCstation SunOS (Rel. 4.1.4), 3.5-inch 2HD FD Solaris (Rel. 2.5.1) 1/4-inch CGMT 3K15 3.5-inch 2HD FD B.3 Control Software Project manager 568 This is control software designed to enable efficient user program development in the Windows environment. All operations used in development of a user program, such as starting the editor, building, and starting the debugger, can be performed from the project manager. <Caution> The project manager is included in the assembler package (RA78K0). It can only be used in Windows. User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS B.4 Flash Memory Writing Tools Flashpro III (part number: FL-PR3, PG-FP3) Flashpro IV (part number: FL-PR4, PG-FP4) Flash programmer Flash programmer dedicated to microcontrollers with on-chip flash memory. FA-64CW FA-64GC-8BS-A FA-64GC FA-64GK-9ET FA-64GB-8EU-A FA-73F1-CN3-A Flash memory writing adapter Flash memory writing adapter used connected to the Flashpro III and Flashpro IV. * FA-64CW: 64-pin plastic SDIP (CW type) * FA-64GC-8BS-A: 64-pin plastic LQFP (GC-8BS type) * FA-64GC: 64-pin plastic QFP (GC-AB8 type) * FA-64GK-9ET: 64-pin plastic TQFP (GK-9ET type) * FA-64GB-8EU-A: 64-pin plastic LQFP (GB-8EU type) * FA-73F1-CN3-A: 73-pin plastic FBGA (F1-CN3 type) Remark FL-PR3, FL-PR4, FA-64CW, FA-64GC-8BS-A, FA-64GC, FA-64GK-9ET, FA-64GB-8EU-A, and FA73F1-CN3-A are products of Naito Densei Machida Mfg. Co., Ltd. Contact: +81-45-475-4191 Naito Densei Machida Mfg. Co., Ltd. B.5 Debugging Tools (Hardware) B.5.1 When using in-circuit emulator IE-78K0-NS, IE-78K0-NS-A (1/2) IE-78K0-NS In-circuit emulator The in-circuit emulator serves to debug hardware and software when developing application systems using a 78K/0 Series product. It corresponds to the integrated debugger (ID78K0-NS). This emulator should be used in combination with a power supply unit, emulation probe, and interface adapter which is required to connect this emulator to the host machine. IE-78K0-NS-PA Performance board This board is connected to the IE-78K0-NS to expand its functions. Adding this board adds a coverage function and enhances debugging functions such as tracer and timer functions. IE-78K0-NS-A In-circuit emulator A combination of the IE-78K0-NS and IE-78K0-NS-PA. IE-70000-MC-PS-B Power supply unit This adapter is used for supplying power from a receptacle of 100 V to 240 V AC. IE-70000-98-IF-C Interface adapter This adapter is required when using a PC-9800 series computer (except notebook type) as the host machine (C bus compatible). IE-70000-CD-IF-A PC card interface This is PC card and interface cable required when using a notebook-type computer as the host machine (PCMCIA socket compatible). IE-70000-PC-IF-C Interface adapter This adapter is required when using an IBM PC/AT compatible computer as the host machine (ISA bus compatible). IE-70000-PCI-IF-A Interface adapter This adapter is required when using a computer with a PCI bus as the host machine. IE-780034-NS-EM1 Emulation board This board emulates the operations of the peripheral hardware peculiar to a device. It should be used in combination with an in-circuit emulator. NP-64CW NP-H64CW Emulation probe This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic SDIP (CW type). User's Manual U14046EJ5V0UD 569 APPENDIX B DEVELOPMENT TOOLS (2/2) NP-64GC Emulation probe This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). EV-9200GC-64 Conversion socket (see Figures B-2 and B-3) NP-64GC-TQ NP-H64GC-TQ Emulation probe This conversion socket connects the NP-64GC to a target system board designed for a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). TGC-064SAP Conversion adapter (see Figure B-4) NP-64GK NP-H64GK-TQ Emulation probe This conversion adapter connects the NP-64GC-TQ or NP-H64GC-TQ to a target system board designed for a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic TQFP (GK-9ET type). TGK-064SBW Conversion adapter (see Figure B-5) NP-H64GB-TQ Emulation probe This conversion adapter connects the NP-64GK or NP-H64GK-TQ to a target system board designed for a 64-pin plastic TQFP (GK-9ET type). This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic LQFP (GB-8EU type). TGB-064SDP Conversion adapter (see Figure B-6) NP-73F1-CN3 Emulation probe This conversion adapter connects the NP-H64GB-TQ to a target system board designed for a 64-pin plastic LQFP (GB-8EU type). This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 73-pin plastic FBGA (F1-CN3 type). CSICE73A0909N01, LSPACK73A0909N01, CSSOCKET73A0909N01 Conversion socket This conversion socket connects the NP-73F1-CN3 to a target system board designed for a 73-pin plastic FBGA (F1-CN3 type). * CSICE73A0909N01: YQSOCKET/LSPACK conversion adapter * LSPACK73A0909N01: Socket for target connection * CSSOCKET73A0909N01: Socket for emulator connection Remarks 1. NP-64CW, NP-H64CW, NP-64GC, NP-64GC-TQ, NP-H64GC-TQ, NP-64GK, NP-H64GK-TQ, NPH64GB-TQ, and NP-73F1-CN3 are products of Naito Densei Machida Mfg. Co., Ltd. Contact: +81-45-475-4191 Naito Densei Machida Mfg. Co., Ltd. 2. TGC-064SAP, TGK-064SBW, TGB-064SDP, CSICE73A0909N01, LSPACK73A0909N01, and CSSOCKET73A0909N01 are products of TOKYO ELETECH CORPORATION. Contact: Daimaru Kogyo, Ltd. Phone: Tokyo +81-3-3820-7112 Electronics Dept. Osaka +81-6-6244-6672 Electronics 2nd Dept. 3. EV-9200GC-64 is sold in five-unit sets. 4. TGK-064SBW and TGC-064SAP are sold in single units. 5. The emulation probe (NP-73F1-CN3) is supplied with a conversion socket (CSICE73A0909N01, LSPACK73A0909N01, CSSOCKET73A0909N01). 570 User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS B.5.2 When using in-circuit emulator IE-78001-R-A IE-78001-R-A In-circuit emulator The in-circuit emulator serves to debug hardware and software when developing application systems using a 78K/0 Series product. It corresponds to the integrated debugger (ID78K0). This emulator should be used in combination with an emulation probe and interface adapter, which is required to connect this emulator to the host machine. IE-70000-98-IF-C Interface adapter This adapter is required when using a PC-9800 series computer (except notebook type) as the host machine (C bus compatible). IE-70000-PC-IF-C Interface adapter This adapter is required when using an IBM PC/AT compatible computer as the host machine (ISA bus compatible). IE-70000-PCI-IF-A Interface adapter This adapter is required when using a computer with a PCI bus as the host machine. IE-780034-NS-EM1 Emulation board This board emulates the operations of the peripheral hardware peculiar to a device. It should be used in combination with an in-circuit emulator and emulation probe conversion board. IE-78K0-R-EX1 Emulation probe conversion board This board is required when using the IE-780034-NS-EM1 on the IE-78001-R-A. EP-78240CW-RNote Emulation probe This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic SDIP (CW type). EP-78240GC-RNote Emulation probe This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). EV-9200GC-64 Conversion socket (see Figures B-2 and B-3) This conversion socket connects the EP-78240GC-R to a target system board designed for a 64-pin plastic QFP (GC-AB8 type) and 64-pin plastic LQFP (GC-8BS type). This probe is used to connect the in-circuit emulator to a target system and is designed for use with a 64-pin plastic TQFP (GK-9ET type). EP-78012GK-R Emulation probe TGK-064SBW Conversion adapter (see Figure B-5) This conversion adapter connects the EP-78012GK-R to a target system board designed for a 64-pin plastic TQFP (GK-9ET type). Note Maintenance product Caution The IE-78001-R-A is not supported for the 64-pin plastic LQFP (GB-8EU type) and 73-pin plastic FBGA (F1-CN3 type). Remarks 1. TGK-064SBW is a product of TOKYO ELETECH CORPORATION. Contact: Daimaru Kogyo, Ltd. Phone: Tokyo +81-3-3820-7112 Electronics Dept. Osaka +81-6-6244-6672 Electronics 2nd Dept. 2. EV-9200GC-64 is sold in five-unit sets. 3. TGK-064SBW is sold in single units. User's Manual U14046EJ5V0UD 571 APPENDIX B DEVELOPMENT TOOLS B.6 Debugging Tools (Software) SM78K0 System simulator This is a system simulator for the 78K/0 Series. The SM78K0 is Windows-based software. It is used to perform debugging at the C source level or assembler level while simulating the operation of the target system on a host machine. Use of the SM78K0 allows the execution of application logical testing and performance testing on an independent basis from hardware development, thereby providing higher development efficiency and software quality. The SM78K0 should be used in combination with the device file (DF780024 or DF780034) (sold separately). Part Number: SxxxxSM78K0 ID78K0-NS Integrated debugger (supporting in-circuit emulators This debugger supports the in-circuit emulators for the 78K/0 Series. The ID78K0-NS is Windows-based software. It has improved C-compatible debugging functions and can display the results of IE-78K0-NS and IE-78K0-NS-A) tracing with the source program using an integrating window function that associates ID78K0 Integrated debugger (supporting in-circuit emulator the source program, disassemble display, and memory display with the trace result. It should be used in combination with the device file (sold separately). IE-78001-R-A) Part Number: SxxxxID78K0-NS, SxxxxID78K0 Remark xxxx in the part number differs depending on the host machine and OS used. SxxxxSM78K0 SxxxxID78K0-NS SxxxxID78K0 xxxx AB13 572 Host Machine IBM PC/AT compatibles OS Windows (Japanese version) BB13 Windows (English version) AB17 Windows (Japanese version) BB17 Windows (English version) User's Manual U14046EJ5V0UD Supply Medium 3.5-inch 2HD FD CD-ROM APPENDIX B DEVELOPMENT TOOLS B.7 Embedded Software RX78K0 is a real-time OS conforming to the ITRON specifications. A tool (configurator) for generating the nucleus of RX78K0 and multiple information tables is supplied. It is used in combination with an assembler package (RA78K0) and device file (DF780024 or DF780034) (both sold separately). <Precaution when using RX78K0 in PC environment> The real-time OS is a DOS-based application. It should be used from the DOS prompt when using in Windows. RX78K0 Real-time OS Part number: SxxxxRX78013- Caution When purchasing the RX78K0, fill in the purchase application form in advance and sign the user agreement. Remark xxxx and in the part number differ depending on the host machine and OS used. SxxxxRX78013- Maximum Number for Use in Mass Production 001 Evaluation object Do not use for mass-produced product. 100K Mass-production object 0.1 million units 001M 1 million units 010M 10 million units S01 xxxx Product Outline Source program Source program for mass-produced object Host Machine OS AA13 PC-9800 series Windows (Japanese version) AB13 IBM PC/AT compatibles Windows (Japanese version) BB13 Supply Medium 3.5-inch 2HD FD Windows (English version) User's Manual U14046EJ5V0UD 573 APPENDIX B DEVELOPMENT TOOLS B.8 System Upgrade from Former In-Circuit Emulator for 78K/0 Series to IE-78001-R-A If you already have a former in-circuit emulator for 78K/0 Series microcontrollers (IE-78000-R or IE-78000-R-A), that in-circuit emulator can operate as an equivalent to the IE-78001-R-A by replacing its internal break board with the IE-78001-R-BK. Table B-1. System Upgrade Method from Former In-Circuit Emulator for 78K/0 Series to IE-78001-R-A In-Circuit Emulator Owned In-Circuit Emulator Cabinet UpgradeNote IE-78000-R Required IE-78000-R-A Not required Board to Be Purchased IE-78001-R-BK Note For upgrading of a cabinet, send your in-circuit emulator to NEC Electronics. 574 User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS B.9 Package Drawings of Conversion Socket and Conversion Adapter Figure B-2. EV-9200GC-64 Package Drawing (for Reference Only) A O Q N F L K T J C D S E M R B EV-9200GC-64 1 P No.1 pin index G H I EV-9200GC-64-G0 ITEM MILLIMETERS INCHES A 18.8 0.74 B 14.1 0.555 C 14.1 0.555 D 18.8 0.74 E 4-C 3.0 4-C 0.118 F 0.8 0.031 G 6.0 0.236 H 15.8 0.622 I 18.5 0.728 J 6.0 0.236 K 15.8 0.622 L 18.5 0.728 M 8.0 0.315 N 7.8 0.307 O 2.5 0.098 P 2.0 0.079 Q 1.35 0.053 R 0.35 0.1 0.014+0.004 -0.005 S 2.3 0.091 T 1.5 0.059 User's Manual U14046EJ5V0UD 575 APPENDIX B DEVELOPMENT TOOLS Figure B-3. EV-9200GC-64 Recommended Board Mounting Pattern (for Reference Only) G J H D E F K I L C B A EV-9200GC-64-P1E ITEM MILLIMETERS A 19.5 B 14.8 0.768 0.583 C 0.8-0.02 x 15=12.0-0.05 D +0.003 0.8-0.02 x 15=12.0-0.05 0.031+0.002 --0.001x 0.591=0.472 --0.002 0.031+0.002 --0.001x 0.591=0.472 +0.003 --0.002 E 14.8 0.583 F 19.5 0.768 G 6.00 - 0.08 0.236 +0.004 --0.003 H 6.00 - 0.08 0.236 +0.004 --0.003 I 0.5 - 0.02 0.197 +0.001 --0.002 J 2.36 - 0.03 0.093 +0.001 --0.002 K 2.2 - 0.1 0.087 +0.004 --0.005 L 1.57 - 0.03 0.062 +0.001 --0.002 Caution 576 INCHES Dimensions of mount pad for EV-9200 and that for target device (QFP) may be different in some parts. For the recommended mount pad dimensions for QFP, refer to "Semiconductor Device Mount Manual" website (http://www.necel.com/pkg/en/mount/index.html). User's Manual U14046EJ5V0UD APPENDIX B DEVELOPMENT TOOLS Figure B-4. TGC-064SAP Package Drawing (for Reference Only) I C A B J K S Protrusion height D T E F G H Q R M N L O P V W d XZ U j i c Y b ITEM A B a e g f h MILLIMETERS 14.12 0.8x15=12.0 INCHES ITEM 0.556 0.031x0.591=0.472 a b MILLIMETERS 1.85 3.5 0.073 0.138 INCHES C 0.8 0.031 c 2.0 0.079 D 20.65 0.813 d 6.0 0.236 E F G 10.0 12.4 14.8 0.394 e f 0.25 13.6 0.010 g 1.2 H I 17.2 C 2.0 0.677 C 0.079 h i 1.2 2.4 J 9.05 0.356 j 2.7 K 5.0 0.197 L 13.35 1.325 0.526 0.052 O 1.325 16.0 0.630 M N 0.488 0.583 P 20.65 0.813 12.5 0.492 R 17.5 0.689 S 4- 1.3 4- 0.051 W X 0.047 0.094 0.106 TGC-064SAP-G0E 0.052 Q T U V 0.535 0.047 1.8 0.071 3.55 0.9 0.3 0.140 0.035 0.012 (19.65) (0.667) Y 7.35 0.289 Z 1.2 0.047 note: Product by TOKYO ELETECH CORPORATION. User's Manual U14046EJ5V0UD 577 APPENDIX B DEVELOPMENT TOOLS Figure B-5. TGK-064SBW Package Drawing (for Reference Only) A B K L X M C T G F E D H I J Protrusion height U S V Q W R N O P a Z e Y d k j h i c b f g INCHES ITEM A B 18.4 0.65x15=9.75 0.724 0.026x0.591=0.384 a b 0.3 1.85 0.073 C D 0.65 0.026 7.75 10.15 0.305 c d 3.5 2.0 0.138 0.079 0.154 ITEM MILLIMETERS INCHES 0.012 0.400 0.494 e 3.9 12.55 f 1.325 0.052 G 14.95 0.589 g 1.325 0.052 H I 0.65x15=9.75 11.85 0.026x0.591=0.384 0.467 h i 5.9 0.8 0.232 0.031 j k 2.4 2.7 0.094 0.106 E F J 18.4 0.724 K C 2.0 C 0.079 L M 12.45 0.490 10.25 0.404 N O 7.7 10.02 0.303 0.394 P 14.92 0.587 Q R 11.1 1.45 0.437 0.057 S 1.45 0.057 T U 4- 1.3 1.8 4- 0.051 V 5.0 0.197 W X 5.3 0.209 4-C 1.0 4-C 0.039 Y 3.55 0.9 0.140 0.035 Z note: Product by TOKYO ELETECH CORPORATION. 578 MILLIMETERS User's Manual U14046EJ5V0UD 0.071 TGK-064SBW-G1E APPENDIX B DEVELOPMENT TOOLS Figure B-6. TGB-064SDP Package Drawing (for Reference Only) (1/2) A B C D J M N U K H G F E I S T Protrusion height V Q L W R O P a Z Y note : Product by TOKYO ELETECH CORPORATION X d c e b ITEM MILLIMETERS INCHES ITEM MILLIMETERS INCHES A 14.0 0.551 a 2.6 0.102 B 9.24 0.364 b 0.25 0.010 C 0.5 x 15=7.5 0.020 x 0.591=0.295 c 9.24 0.364 D 0.5 0.020 d 1.38 0.054 E 5.64 0.222 e 1.38 0.054 F 8.04 0.317 G 10.44 0.411 H 12.84 0.506 I 9.77 0.385 J K C 1.0 4.3 C 0.039 0.169 L M 4- 0.7 10.1 4- 0.028 0.398 N 8.0 0.315 O 8.99 0.354 P Q 12.0 1.505 0.472 0.059 R 1.505 0.059 S 6.75 0.266 T 12.9 0.508 U 5.0 0.197 V 1.8 0.071 W X 0.25 1.85 0.010 0.073 Y 3.5 0.138 Z 2.0 0.079 TGB-064SDP-G1E-1 User's Manual U14046EJ5V0UD 579 APPENDIX B DEVELOPMENT TOOLS Figure B-6. TGB-064SDP Package Drawing (for Reference Only) (2/2) A J B I K O C M L X W N G F E D V P H Y S R Z a U T Q note : Product by TOKYO ELETECH CORPORATION ITEM MILLIMETERS A 16.0 INCHES 0.630 B 0.5 x 15=7.5 0.020 x 0.591=0.295 C 0.5 0.020 D 5.64 0.222 E 8.04 0.317 F 10.44 0.411 G 12.84 0.506 H 9.77 0.385 I C 2.0 C 0.079 J 5.9 0.232 K 2.7 0.106 L M N 2.4 0.8 3.5 0.094 0.031 0.138 O 0.3 P Q 0.9 0.012 0.035 13.6 0.535 R 6.0 0.236 S 1.0 0.039 T 4.2 0.165 U 0.2 4.0 0.7 1.03 1.1 0.7 0.008 0.157 0.028 0.041 0.043 0.028 V W X Y Z TGB-064SDP-G1E-2 580 User's Manual U14046EJ5V0UD ITEM MILLIMETERS 1.4 a INCHES 0.055 APPENDIX C NOTES ON TARGET SYSTEM DESIGN The following shows a diagram of the connection conditions between the emulation probe and conversion adapter. Design your system making allowances for conditions such as the shape of parts mounted on the target system, as shown below. Of the products described in this chapter, all the emulation probes are products of Naito Densei Machida Mfg. Co., Ltd., and all the conversion adapters are products of TOKYO ELETECH CORPORATION. Table C-1. Distance Between IE System and Conversion Adapter Emulation Probe Conversion Adapter - NP-64CW NP-H64CW NP-64GC-TQ TGC-064SAP 155 mm 355 mm TGK-064SBW 155 mm NP-H64GK-TQ NP-64GB-TQ 355 mm TGB-064SDP 155 mm NP-H64GB-TQ NP-73F1-CN3 170 mm 370 mm NP-H64GC-TQ NP-64GK Distance Between IE System and Conversion Adapter 355 mm CSICE73A0909N01, LSPACK73A0909N01, CSSOCKET73A0909N01 User's Manual U14046EJ5V0UD 213 mm 581 APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-1. Distance Between In-Circuit Emulator and Conversion Adapter (When Using 64CW) In-circuit emulator IE-78K0-NS or IE-78K0-NS-A Target system Emulation board IE-780034-NS-EM1 170 mmNote CN5 Emulation probe NP-64CW, NP-H64CW IC socket Note Distance when using NP-64CW. This is 370 mm when using NP-H64CW. Figure C-2. Connection Conditions of Target System (When Using NP-64CW) Emulation board IE-780034-NS-EM1 Emulation probe NP-64CW 20 mm 14 mm 13 mm 34 mm 8 mm 24 mm 8 mm 13 mm Target system 582 User's Manual U14046EJ5V0UD APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-3. Connection Conditions of Target System (When Using NP-H64CW) Emulation board IE-780034-NS-EM1 Emulation probe NP-H64CW 19 mm 42 mm 23 mm 45 mm 60 mm Target system User's Manual U14046EJ5V0UD 583 APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-4. Distance Between In-Circuit Emulator and Conversion Adapter (When Using 64GC) In-circuit emulator IE-78K0-NS or IE-78K0-NS-A Target system Emulation board IE-780034-NS-EM1 155 mm Note CN6 Emulation probe NP-64GC-TQ, NP-H64GC-TQ Conversion adapter: TGC-064SAP Note Distance when using NP-64GC-TQ. This is 355 mm when using NP-H64GC-TQ. Figure C-5. Connection Conditions of Target System (When Using NP-64GC-TQ) Emulation board IE-780034-NS-EM1 Emulation probe NP-64GC-TQ 23 mm Conversion adapter TGC-064SAP 11 mm 25 mm 20.65 mm 40 mm Pin 1 20.65 mm 34 mm Target system 584 User's Manual U14046EJ5V0UD APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-6. Connection Conditions of Target System (When Using NP-H64GC-TQ) Emulation board IE-780034-NS-EM1 Emulation probe NP-H64GC-TQ 23 mm Conversion adapter: TGC-064SAP 11 mm 23 mm 20.65 mm 42 mm Pin 1 20.65 mm 45 mm Target system User's Manual U14046EJ5V0UD 585 APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-7. Distance Between In-Circuit Emulator and Conversion Adapter (When Using 64GK) In-circuit emulator IE-78K0-NS or IE-78K0-NS-A Target system Emulation board IE-780034-NS-EM1 Note 155 mm CN6 Emulation probe NP-64GK, NP-H64GK-TQ Conversion adapter: TGK-064SBW Note Distance when using NP-64GK. This is 355 mm when using NP-H64GK-TQ. Figure C-8. Connection Conditions of Target System (When Using NP-64GK) Emulation board IE-780034-NS-EM1 Emulation probe NP-64GK 21.95 mm Conversion adapter TGK-064SBW 11 mm 25 mm 18.4 mm 40 mm Pin 1 18.4 mm 34 mm Target system 586 User's Manual U14046EJ5V0UD APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-9. Connection Conditions of Target System (When Using NP-H64GK-TQ) Emulation board IE-780034-NS-EM1 Emulation probe NP-H64GK-TQ 21.95 mm Conversion adapter TGK-064SBW 23 mm 18.4 mm 42 mm 11 mm Pin 1 18.4 mm 45 mm Target system User's Manual U14046EJ5V0UD 587 APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-10. Distance Between In-Circuit Emulator and Conversion Adapter (When Using 64GB) In-circuit emulator IE-78K0-NS or IE-78K0-NS-A Target system Emulation board IE-780034-NS-EM1 Note 155 mm CN6 Emulation probe NP-64GB-TQ, NP-H64GB-TQ Conversion adapter: TGB-064SDP Note Distance when using NP-64GB-TQ. This is 355 mm when using NP-H64GB-TQ. Figure C-11. Connection Conditions of Target System (When Using NP-64GB-TQ) Emulation board IE-780034-NS-EM1 Emulation probe NP-64GB-TQ 22 mm Conversion adapter TGB-064SDP 11 mm 16 mm 40 mm Pin 1 16 mm 34 mm Target system 588 User's Manual U14046EJ5V0UD APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-12. Connection Conditions of Target System (When Using NP-H64GB-TQ) Emulation board IE-780034-NS-EM1 Emulation probe NP-H64GB-TQ 21.4 mm Conversion adapter TGB-064SDP 11 mm 16 mm 42.6 mm Pin 1 16 mm 45 mm Target system User's Manual U14046EJ5V0UD 589 APPENDIX C NOTES ON TARGET SYSTEM DESIGN Figure C-13. Distance Between In-Circuit Emulator and Conversion Socket (When Using NP-73F1-CN3) In-circuit emulator IE-78K0-NS or IE-78K0-NS-A Target system Emulation board IE-780034-NS-EM1 213 mm CN6 Emulation probe NP-73F1-CN3 Conversion socket: CSICE73A0909N01, LSPACK73A0909N01, CSSOCKET73A0909N01 Figure C-14. Connection Conditions of Target System (When Using NP-73F1-CN3) Emulation board IE-780034-NS-EM1 Conversion socket CSICE73A0909N01, LSPACK73A0909N01, CSSOCKET73A0909N01 Emulation probe NP-73F1-CN3 21 mm 20 mm 23 mm 27 mm 23 mm 33 mm Target system 590 User's Manual U14046EJ5V0UD APPENDIX D REGISTER INDEX D.1 Register Name Index [A] A/D conversion result register 0 (ADCR0) ...................................................................................................... 257, 279 A/D converter mode register 0 (ADM0) .......................................................................................................... 259, 281 Analog input channel specification register 0 (ADS0) ................................................................................... 261, 283 Asynchronous serial interface mode register 0 (ASIM0) ........................................................................................ 303 Asynchronous serial interface status register 0 (ASIS0) ........................................................................................ 302 [B] Baud rate generator control register 0 (BRGC0) .................................................................................................... 305 [C] Capture/compare control register 0 (CRC0) ............................................................................................................ 188 Clock output select register (CKS) ........................................................................................................................... 251 [E] 8-bit timer compare register 50 (CR50) ................................................................................................................... 219 8-bit timer compare register 51 (CR51) ................................................................................................................... 219 8-bit timer counter 50 (TM50) ................................................................................................................................... 219 8-bit timer counter 51 (TM51) ................................................................................................................................... 219 8-bit timer mode control register 50 (TMC50) ......................................................................................................... 221 8-bit timer mode control register 51 (TMC51) ......................................................................................................... 221 External interrupt falling edge enable register (EGN) ............................................................................................. 408 External interrupt rising edge enable register (EGP) .............................................................................................. 408 [I] IIC control register 0 (IICC0) .................................................................................................................................... 343 IIC shift register 0 (IIC0) ........................................................................................................................................... 341 IIC status register 0 (IICS0) ...................................................................................................................................... 348 IIC transfer clock select register 0 (IICCL0) ............................................................................................................ 351 Interrupt mask flag register 0H (MK0H) ................................................................................................................... 406 Interrupt mask flag register 0L (MK0L) .................................................................................................................... 406 Interrupt mask flag register 1L (MK1L) .................................................................................................................... 406 Interrupt request flag register 0H (IF0H) ................................................................................................................. 405 Interrupt request flag register 0L (IF0L) ................................................................................................................... 405 Interrupt request flag register 1L (IF1L) ................................................................................................................... 405 [M] Memory expansion mode register (MEM) ................................................................................................................ 423 Memory expansion wait setting register (MM) ........................................................................................................ 424 Memory size switching register (IMS) ...................................................................................................................... 448 [O] Oscillation stabilization time select register (OSTS) ...................................................................................... 172, 432 User's Manual U14046EJ5V0UD 591 APPENDIX D REGISTER INDEX [P] Port 0 (P0) ................................................................................................................................................................. 137 Port 1 (P1) ................................................................................................................................................................. 139 Port 2 (P2) ................................................................................................................................................................. 140 Port 3 (P3) ........................................................................................................................................................ 143, 148 Port 4 (P4) ................................................................................................................................................................. 152 Port 5 (P5) ................................................................................................................................................................. 153 Port 6 (P6) ................................................................................................................................................................. 154 Port 7 (P7) ................................................................................................................................................................. 156 Port mode register 0 (PM0) ...................................................................................................................................... 159 Port mode register 2 (PM2) .................................................................................................................... 159, 307, 332 Port mode register 3 (PM3) .................................................................................................................... 159, 332, 352 Port mode register 4 (PM4) ...................................................................................................................................... 159 Port mode register 5 (PM5) ...................................................................................................................................... 159 Port mode register 6 (PM6) ...................................................................................................................................... 159 Port mode register 7 (PM7) ............................................................................................................ 159, 191, 224, 253 Prescaler mode register 0 (PRM0) .......................................................................................................................... 190 Priority specification flag register 0H (PR0H) .......................................................................................................... 407 Priority specification flag register 0L (PR0L) ........................................................................................................... 407 Priority specification flag register 1L (PR1L) ........................................................................................................... 407 Processor clock control register (PCC) ................................................................................................................... 169 Program status word (PSW) ............................................................................................................................ 112, 409 Pull-up resistor option register 0 (PU0) ................................................................................................................... 163 Pull-up resistor option register 2 (PU2) ................................................................................................................... 163 Pull-up resistor option register 3 (PU3) ................................................................................................................... 163 Pull-up resistor option register 4 (PU4) ................................................................................................................... 163 Pull-up resistor option register 5 (PU5) ................................................................................................................... 163 Pull-up resistor option register 6 (PU6) ................................................................................................................... 163 Pull-up resistor option register 7 (PU7) ................................................................................................................... 163 [R] Receive buffer register 0 (RXB0) ............................................................................................................................. 301 Receive shift register 0 (RX0) .................................................................................................................................. 301 [S] Serial I/O shift register 30 (SIO30) .......................................................................................................................... 328 Serial I/O shift register 31 (SIO31) .......................................................................................................................... 328 Serial operation mode register 30 (CSIM30) ........................................................................................................... 329 Serial operation mode register 31 (CSIM31) ........................................................................................................... 329 16-bit timer capture/compare register 00 (CR00) ................................................................................................... 184 16-bit timer capture/compare register 01 (CR01) ................................................................................................... 185 16-bit timer counter 0 (TM0) ..................................................................................................................................... 184 16-bit timer mode control register 0 (TMC0) ........................................................................................................... 186 16-bit timer output control register 0 (TOC0) .......................................................................................................... 189 Slave address register 0 (SVA0) .............................................................................................................................. 341 592 User's Manual U14046EJ5V0UD APPENDIX D REGISTER INDEX [T] Timer clock select register 50 (TCL50) .................................................................................................................... 220 Timer clock select register 51 (TCL51) .................................................................................................................... 220 Transmit shift register 0 (TXS0) ............................................................................................................................... 301 [W] Watch timer operation mode register (WTM) .......................................................................................................... 242 Watchdog timer clock select register (WDCS) ........................................................................................................ 246 Watchdog timer mode register (WDTM) .................................................................................................................. 247 User's Manual U14046EJ5V0UD 593 APPENDIX D REGISTER INDEX D.2 Register Symbol Index [A] ADCR0: A/D conversion result register 0 ................................................................................................ 257, 279 ADM0: A/D converter mode register 0 ................................................................................................... 259, 281 ADS0: Analog input channel specification register 0 ........................................................................... 261, 283 ASIM0: Asynchronous serial interface mode register 0 ................................................................................. 303 ASIS0: Asynchronous serial interface status register 0 ................................................................................. 302 [B] BRGC0: Baud rate generator control register 0 ............................................................................................... 305 [C] CKS: Clock output select register ................................................................................................................ 251 CR00: 16-bit timer capture/compare register 00 ........................................................................................... 184 CR01: 16-bit timer capture/compare register 01 ........................................................................................... 185 CR50: 8-bit timer compare register 50 .......................................................................................................... 219 CR51: 8-bit timer compare register 51 .......................................................................................................... 219 CRC0: Capture/compare control register 0 .................................................................................................... 188 CSIM30: Serial operation mode register 30 ...................................................................................................... 329 CSIM31: Serial operation mode register 31 ...................................................................................................... 329 [E] EGN: External interrupt falling edge enable register ................................................................................... 408 EGP: External interrupt rising edge enable register .................................................................................... 408 [I] IF0H: Interrupt request flag register 0H ....................................................................................................... 405 IF0L: Interrupt request flag register 0L ........................................................................................................ 405 IF1L: Interrupt request flag register 1L ........................................................................................................ 405 IIC0: IIC shift register 0 ................................................................................................................................ 341 IICC0: IIC control register 0 ............................................................................................................................ 343 IICCL0: IIC transfer clock select register 0 ...................................................................................................... 351 IICS0: IIC status register 0 ............................................................................................................................. 348 IMS: Memory size switching register .......................................................................................................... 448 [M] MEM: Memory expansion mode register ...................................................................................................... 423 MK0H: Interrupt mask flag register 0H ........................................................................................................... 406 MK0L: Interrupt mask flag register 0L ............................................................................................................ 406 MK1L: Interrupt mask flag register 1L ............................................................................................................ 406 MM: Memory expansion wait setting register ............................................................................................. 424 [O] OSTS: 594 Oscillation stabilization time select register .............................................................................. 172, 432 User's Manual U14046EJ5V0UD APPENDIX D REGISTER INDEX [P] P0: Port 0 .................................................................................................................................................... 137 P1: Port 1 .................................................................................................................................................... 139 P2: Port 2 .................................................................................................................................................... 140 P3: Port 3 ........................................................................................................................................... 143, 148 P4: Port 4 .................................................................................................................................................... 152 P5: Port 5 .................................................................................................................................................... 153 P6: Port 6 .................................................................................................................................................... 154 P7: Port 7 .................................................................................................................................................... 156 PCC: Processor clock control register ......................................................................................................... 169 PM0: Port mode register 0 ............................................................................................................................ 159 PM2: Port mode register 2 .......................................................................................................... 159, 307, 332 PM3: Port mode register 3 .......................................................................................................... 159, 332, 352 PM4: Port mode register 4 ............................................................................................................................ 159 PM5: Port mode register 5 ............................................................................................................................ 159 PM6: Port mode register 6 ............................................................................................................................ 159 PM7: Port mode register 7 .................................................................................................. 159, 191, 224, 253 PR0H: Priority specification flag register 0H .................................................................................................. 407 PR0L: Priority specification flag register 0L .................................................................................................. 407 PR1L: Priority specification flag register 1L .................................................................................................. 407 PRM0: Prescaler mode register 0 ................................................................................................................... 190 PSW: Program status word .................................................................................................................. 112, 409 PU0: Pull-up resistor option register 0 ........................................................................................................ 163 PU2: Pull-up resistor option register 2 ........................................................................................................ 163 PU3: Pull-up resistor option register 3 ........................................................................................................ 163 PU4: Pull-up resistor option register 4 ........................................................................................................ 163 PU5: Pull-up resistor option register 5 ........................................................................................................ 163 PU6: Pull-up resistor option register 6 ........................................................................................................ 163 PU7: Pull-up resistor option register 7 ........................................................................................................ 163 [R] RX0: Receive shift register 0 ....................................................................................................................... 301 RXB0: Receive buffer register 0 ..................................................................................................................... 301 [S] SIO30: Serial I/O shift register 30 ................................................................................................................... 328 SIO31: Serial I/O shift register 31 ................................................................................................................... 328 SVA0: Slave address register 0 ..................................................................................................................... 341 [T] TCL50: Timer clock select register 50 ............................................................................................................. 220 TCL51: Timer clock select register 51 ............................................................................................................. 220 TM0: 16-bit timer counter 0 .......................................................................................................................... 184 TM50: 8-bit timer counter 50 .......................................................................................................................... 219 TM51: 8-bit timer counter 51 .......................................................................................................................... 219 TMC0: 16-bit timer mode control register 0 ................................................................................................... 186 TMC50: 8-bit timer mode control register 50 ................................................................................................... 221 TMC51: 8-bit timer mode control register 51 ................................................................................................... 221 User's Manual U14046EJ5V0UD 595 APPENDIX D REGISTER INDEX TOC0: 16-bit timer output control register 0 .................................................................................................. 189 TXS0: Transmit shift register 0 ...................................................................................................................... 301 [W] WDCS: Watchdog timer clock select register ................................................................................................. 246 WDTM: Watchdog timer mode register ............................................................................................................ 247 WTM: Watch timer operation mode register ................................................................................................. 242 596 User's Manual U14046EJ5V0UD APPENDIX E REVISION HISTORY E.1 Major Revisions in This Edition Page Description Throughout Addition of lead-free products p. 22 CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) * Modification of description in 1.3 Applications p. 49 CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) * Modification of description in 2.2 Applications p. 77 CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) * Modification of AVREF pin function after reset in 3.1 Pin Function List (2) Non-port pins p. 89 CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) * Modification of AVREF pin function after reset in 4.1 Pin Function List (2) Non-port pins p. 117 CHAPTER 5 CPU ARCHITECTURE * Modification of description in 5.2.3 Special function register (SFR) p. 244 CHAPTER 10 WATCH TIMER * Modification of Caution description in Figure 10-3 Operation Timing of Watch Timer/Interval Timer p. 276 CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) * Modification of C1 value in Table 13-3 Resistances and Capacitances of Equivalent Circuit (Reference Values) p. 297 CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) * Modification of C1 value in Table 14-3 Resistances and Capacitances of Equivalent Circuit (Reference Values) p. 315 CHAPTER 16 SERIAL INTERFACE UART0 * Modification of Figure 16-9 (i) Stop bit length: 1 bit pp. 365, 371 CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) * Modification of Figure 18-18 Communication Reservation Timing * Modification of Figure 18-21 Master Operation Flowchart (5/5) pp. 401, 405, CHAPTER 19 INTERRUPT FUNCTIONS 410, 413 * Correction of description in Table 19-1 Interrupt Source List * Modification of Caution 5 in Figure 19-2 Format of Interrupt Request Flag Registers (IF0L, IF0H, IF1L) * Modification of description in 19.4.1 Non-maskable interrupt request acknowledgment operation * Modification of description in 19.4.2 Maskable interrupt request acknowledgment operation pp. 450, 452, CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY 453, 457 * Correction of description in Table 23-8 Communication Mode List * Modification of Note in Figure 23-4 Example of Connection with Dedicated Flash Programmer * Modification of description in <Power supply> in 23.5.3 On-board pin processing pp. 472, 479 CHAPTER 24 INSTRUCTION SET * Deletion of description on NMIS in 24.1.2 Description of "operation" column * Modification of Operation column of RETI of call/return instructions in 24.2 Operation List pp. 504, 505 CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDED-SPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) * Modification of C1 value in [Parameter values] of input impedance of analog input pin pp. 526, 535, CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) 536 * Deletion of Notes 2 and 3 of supply current IDD3, IDD4, and IDD5 in DC Characteristics (TA = -40 to +85C, VDD = 1.8 to 5.5 V) * Modification of C1 value in [Parameter values] of input impedance of analog input pin User's Manual U14046EJ5V0UD 597 APPENDIX E Page REVISION HISTORY Description pp. 554 to 557 CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS * Modification of a soldering condition of partial heating soldering method in Table 28-1 Surface Mounting Type Soldering Conditions p. 564 APPENDIX B DEVELOPMENT TOOLS * Addition of Windows XP to Windows 598 User's Manual U14046EJ5V0UD APPENDIX E REVISION HISTORY E.2 Revision History up to Previous Edition Revisions up to the previous edition are shown below. The "Applied to:" column indicates the chapter in each edition to which the revision was applied. (1/5) Edition Second edition Revision from Previous Edition Deletion of the following products * PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A), Applied to: Throughout 780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A) Deletion of the following package * 64-pin plastic LQFP (GK-8A8 type) Addition of the following packages * 64-pin plastic TQFP (GK-9ET type) * 64-pin plastic LQFP (GB-8EU type) Modification of recommended connection of unused pins in Table 3-1 Pin I/O Circuit Types CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) Modification of recommended connection of unused pins in Table 4-1 Pin I/O Circuit Types CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) Modification of Figure 6-2 P00 to P03 Block Diagram CHAPTER 6 PORT FUNCTIONS Modification of Figure 6-4 P20, P22, P23, P25 Block Diagram Modification of Figure 6-7 P34 and P36 Block Diagram (PD780024A, 780034A Subseries) Modification of Figure 6-8 P35 Block Diagram (PD780024A, 780034A Subseries) Modification of Figure 6-10 P32 and P33 Block Diagram (PD780024AY, 780034AY Subseries) Modification of Figure 6-12 P40 to P47 Block Diagram Modification of Figure 6-14 P50 to P57 Block Diagram Modification of Figure 6-15 P64 to P67 Block Diagram Modification of Figure 6-16 P70 to P73 Block Diagram Modification of Figure 6-17 P74 and P75 Block Diagram Addition of note for feedback resistor in Figure 7-3 Processor Clock Control Register (PCC) Format CHAPTER 7 CLOCK GENERATOR Deletion of one-shot pulse output function CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Addition of caution for INTWT in Figure 10-3 Operation Timing of Watch Timer/Interval Timer CHAPTER 10 WATCH TIMER Addition of 13.5 How to Read A/D Converter Characteristics Table CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) 13.6 A/D Converter Cautions Addition of (10) Timing at which A/D conversion result is undefined Addition of (11) Notes on board design Addition of (13) AVREF pin Addition of (14) Internal equivalent circuit of ANI0 to ANI7 pins and permissible signal source impedance Addition of 14.5 How to Read A/D Converter Characteristics Table 14.6 A/D Converter Cautions Addition of (10) Timing at which A/D conversion result is undefined Addition of (11) Notes on board design Addition of (13) AVREF pin Addition of (14) Internal equivalent circuit of ANI0 to ANI7 pins and permissible signal source impedance User's Manual U14046EJ5V0UD CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) 599 APPENDIX E REVISION HISTORY (2/5) Edition Second edition Third edition Revision from Previous Edition Applied to: Modification of Figure 18-3 IIC Control Register 0 (IICC0) Format CHAPTER 18 SERIAL INTERFACE (IIC0) (PD780024AY, 780034AY SUBSERIES ONLY) Deletion of Flashpro II CHAPTER 23 PD78F0034A, 78F0034AY Revision of development tools APPENDIX B DEVELOPMENT TOOLS Addition of the following products PD780021AY(A), 780022AY(A), 780023AY(A), 780024AY(A), PD780031AY(A), 780032AY(A), 780033AY(A), 780034AY(A), PD78F0034B, 78F0034B(A), 78F0034BY, 78F0034BY(A) Throughout Addition of the following packages * 64-pin plastic LQFP (GC-8BS type) * 73-pin plastic FBGA (F1-CN3 type) Addition of expanded-specification products to PD780024A, 780034A Subseries Addition of 1.1 Expanded-Specification Products and Conventional Products CHAPTER 1 OUTLINE (PD780024A, 780034A SUBSERIES) Addition of 1.10 Correspondence Between Mask ROM Versions and Flash Memory Versions Modification of 1.11 Differences Between Standard Grade Products and Special Grade Products Addition of 1.12 Correspondence Between Products and Packages Addition of 2.9 Correspondence Between Mask ROM Versions and Flash Memory Versions CHAPTER 2 OUTLINE (PD780024AY, 780034AY SUBSERIES) Modification of 2.10 Differences Between Standard Grade Products and Special Grade Products Addition of 2.11 Correspondence Between Products and Packages Addition of description of pin processing in 3.2.18 VPP (flash memory versions only) CHAPTER 3 PIN FUNCTION (PD780024A, 780034A SUBSERIES) Modification of Table 3-1 Pin I/O Circuit Types Addition of description of pin processing in 4.2.18 VPP (flash memory versions only) CHAPTER 4 PIN FUNCTION (PD780024AY, 780034AY SUBSERIES) Modification of Table 4-1 Pin I/O Circuit Types Addition of description of program area in 5.1.2 Internal data memory space CHAPTER 5 CPU ARCHITECTURE Modification of Figure 5-14 Data to Be Saved to Stack Memory and Figure 5-15 Data to Be Restored from Stack Memory Modification of [Description example] in 5.4.4 Short direct addressing Addition of [Illustration] in 5.4.7 Based addressing, 5.4.8 Based indexed addressing, and 5.4.9 Stack addressing Modification of port block diagram (Figures 6-2 Block Diagram of P00 to P03 to 6-23 Block Diagram of P74 and P75) Addition of Table 6-6 Port Mode Registers and Output Latch Settings When Alternate Function Is Used 600 User's Manual U14046EJ5V0UD CHAPTER 6 PORT FUNCTIONS APPENDIX E REVISION HISTORY (3/5) Edition Third edition Revision from Previous Edition Applied to: Addition of description of internal feedback resistor and oscillation stabilization time select register (OSTS) in 7.3 Clock Generator Control Registers CHAPTER 7 CLOCK GENERATOR Modification of Figure 8-1 Block Diagram of 16-Bit Timer/Event Counter 0 CHAPTER 8 16-BIT TIMER/EVENT COUNTER 0 Modification of Tables 8-2 TI00/TO0/P70 Pin Valid Edge and CR00, CR01 Capture Trigger and 8-3 TI01/P71 Pin Valid Edge and CR00 Capture Trigger in 2nd edition to Table 8-2 CR00 Capture Trigger and Valid Edges of TI00 and TI01 Pins and Table 8-3 CR01 Capture Trigger and Valid Edge of TI00 Pin (CRC02 = 1) Modification of description procedure of each function in 8.4 Operation of 16-Bit Timer/Event Counter 0 Addition of Figure 8-26 PPG Output Configuration Diagram and Figure 8-27 PPG Output Operation Timing Addition of 8.5 Program List Modification of 8.6 (3) Capture register data retention timing and addition of (11) STOP mode or main system clock stop mode setting Modification of Figures 9-1 Block Diagram of 8-Bit Timer/Event Counter 50 and 9-2 Block Diagram of 8-Bit Timer/Event Counter 51 CHAPTER 9 8-BIT TIMER/EVENT COUNTERS 50, 51 Deletion of Caution in Figures 9-5 Format of 8-Bit Timer Mode Control Register 50 (TMC50) and 9-6 Format of 8-Bit Timer Mode Control Register 51 (TMC51) Addition of [Setting] in 9.4.2 External event counter operation Addition of description of frequency to [Setting] in 9.4.3 Squarewave output (8-bit resolution) operation Addition of description of cycle and duty ratio to [Setting] in 9.4.4 8-bit PWM output operation Addition of 9.5 Program List Deletion of 9.5 (2) Operation after compare register change during timer count operation in 2nd edition Deletion of oscillation stabilization time select register (OSTS) from 11.3 Registers to Control Watchdog Timer in 2nd edition CHAPTER 11 WATCHDOG TIMER Modification of Figure 12-1 Block Diagram of Clock Output/Buzzer CHAPTER 12 CLOCK OUTPUT/ Output Controller BUZZER OUTPUT CONTROLLER Modification of description in 13.2 (3) Sample & hold circuit, (4) Voltage comparator, and addition of (10) ADTRG pin CHAPTER 13 8-BIT A/D CONVERTER (PD780024A, 780024AY SUBSERIES) Addition of Table 13-2 Sampling Time and A/D Conversion Start Delay Time of A/D Converter Deletion of 13.6 (4) Noise countermeasures (contents of deletion are added to Figure 13-18 Example of Connecting Capacitor to AVREF Pin and Figure 13-20 Example of Connection If Signal Source Impedance Is High), and addition of (14) Input impedance of ANI0 to ANI7 pins Modification of Table 13-3 Resistances and Capacitances of Equivalent Circuit (Reference Values) User's Manual U14046EJ5V0UD 601 APPENDIX E REVISION HISTORY (4/5) Edition Third edition Revision from Previous Edition Addition of Figure 14-2 Format of A/D Conversion Result Register 0 (ADCR0) Applied to: CHAPTER 14 10-BIT A/D CONVERTER (PD780034A, 780034AY SUBSERIES) Modification of description in 14.2 (3) Sample & hold circuit, (4) Voltage comparator, and addition of (10) ADTRG pin Addition of Table 14-2 Sampling Time and A/D Conversion Start Delay Time of A/D Converter Deletion of 14.6 (4) Noise countermeasures (contents of deletion are added to Figure 14-19 Example of Connecting Capacitor to AVREF Pin and Figure 14-21 Example of Connection If Signal Source Impedance Is High), and addition of (14) Input impedance of ANI0 to ANI7 pins Modification of Table 14-3 Resistances and Capacitances of Equivalent Circuit (Reference Values) Modification of Figure 16-1 Block Diagram of Serial Interface UART0 CHAPTER 16 SERIAL INTERFACE UART0 Move of description of asynchronous serial interface status register 0 (ASIS0) in 16.3 Registers to Control Serial Interface UART0 to 16.2 Configuration of Serial Interface UART0 Addition of Caution in Figure 16-7 Error Tolerance (When k = 0 ), Including Sampling Errors Modification of Caution in Figure 16-10 Timing of Asynchronous Serial Interface Receive Completion Interrupt Request Addition of (1) Registers to be used and (3) Relationship between main system clock and baud rate in 16.4.3 Infrared data transfer mode Addition of Table 16-6 Register Settings Modification of Figure 17-1 Block Diagram of Serial Interface SIO3n CHAPTER 17 SERIAL INTERFACES SIO30 AND SIO31 Addition of Note 3 and Caution in Figures 17-2 Format of Serial Operation Mode Register 30 (CSIM30) and 17-3 Format of Serial Operation Mode Register 31 (CSIM31) Addition of Table 17-2 Register Settings Modification of Figure 18-1 Block Diagram of Serial Interface IIC0 Unification of 18.2 (1) IIC shift register 0 (IIC0) and (4) IIC shift register 0 (IIC0) in 2nd edition, and (2) Slave address register 0 (SVA0) and (3) Slave address register 0 (SVA0) in 2nd edition Addition of description to "Transfer lines" in Figure 18-16 Wait Signal Addition of description to Notes 1 and 2 in Table 18-2 INTIIC0 Timing and Wait Control Modification of Figure 18-21 Master Operation Flowchart Modification of 18.5.15 (2) Slave operation Modification of (1) Start condition ~ address and (2) Data in Figure 18-23 Example of Master to Slave Communication (When 9-Clock Wait Is Selected for Both Master and Slave) Modification of Figure 18-24 Example of Slave to Master Communication (When 9-Clock Wait Is Selected for Both Master and Slave) 602 User's Manual U14046EJ5V0UD CHAPTER 18 SERIAL INTERFACE IIC0 (PD780024AY, 780034AY SUBSERIES ONLY) APPENDIX E REVISION HISTORY (5/5) Edition Third edition Revision from Previous Edition Modification of (E) Software interrupt in Figure 19-1 Basic Configuration of Interrupt Function Applied to: CHAPTER 19 INTERRUPT FUNCTIONS Addition of Caution 5 in Figure 19-2 Format of Interrupt Request Flag Registers (IF0L, IF0H, IF1L) Addition of Caution in Figure 19-5 Format of External Interrupt Rising Edge Enable Register (EGP), External Interrupt Falling Edge Enable Register (EGN) Addition of description and Remark in 19.4.1 Non-maskable interrupt request acknowledgment operation Addition of description in 19.4.2 Maskable interrupt request acknowledgment operation Addition of an item in Table 19-4 Interrupt Requests Enabled for Nesting During Interrupt Servicing Addition of description of using expanded-specification products CHAPTER 20 EXTERNAL DEVICE EXPANSION FUNCTION Addition of clock output and buzzer output in Table 21-1 HALT Mode Operating Statuses CHAPTER 21 STANDBY FUNCTION Modification of clock output in Table 21-3 STOP Mode Operating Statuses Revision of description CHAPTER 23 PD78F0034A, 78F0034B, 78F0034AY, 78F0034BY Addition of description CHAPTER 25 ELECTRICAL SPECIFICATIONS (EXPANDEDSPECIFICATION PRODUCTS: fX = 1.0 TO 12 MHz) CHAPTER 26 ELECTRICAL SPECIFICATIONS (CONVENTIONAL PRODUCTS: fX = 1.0 TO 8.38 MHz) CHAPTER 27 PACKAGE DRAWINGS CHAPTER 28 RECOMMENDED SOLDERING CONDITIONS Revision of description APPENDIX A DIFFERENCES BETWEEN PD78018F, 780024A, 780034A, AND 780078 SUBSERIES Revision of description APPENDIX B DEVELOPMENT TOOLS Addition of description APPENDIX C NOTES ON TARGET SYSTEM DESIGN User's Manual U14046EJ5V0UD 603