LCD-016N002B-YYH-ET www.vishay.com Vishay 16 x 2 Character LCD FEATURES * Type: character * Display format: 16 x 2 characters * Built-in controller: ST7066U (or equivalent) * Duty cycle: 1/16 * 5 x 8 dots includes cursor * + 5 V power supply * LED can be driven by pin 1, pin 2, or A and K * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 MECHANICAL DATA ITEM ABSOLUTE MAXIMUM RATINGS STANDARD VALUE Module Dimension UNIT ITEM 80.0 x 36.0 x 13.2 (max.) SYMBOL STANDARD VALUE MIN. TYP. MAX. Viewing Area 66.0 x 16.0 Power Supply VDD to VSS -0.3 - 7 Dot Size 0.55 x 0.65 Input Voltage VSS - VDD Dot Pitch 0.60 x 0.70 Mounting Hole 75.0 x 31.0 Character Size 2.95 x 5.55 mm VI UNIT V Note * VSS = 0 V, VDD = 5.0 V ELECTRICAL CHARACTERISTICS ITEM SYMBOL CONDITION Input Voltage VDD Supply Current IDD Recommended LC Driving Voltage for Normal Temperature Version Module VDD to V0 STANDARD VALUE UNIT MIN. TYP. MAX. VDD = + 5 V 4.5 5.0 5.5 V VDD = + 5 V 1.0 1.2 1.5 mA 5.2 - 20 C - - 0 C - - - 25 C 3.6 3.7 3.8 50 C - - - 70 C 3.2 - - V LED Forward Voltage VF 25 C 3.9 4.1 4.3 V LED Forward Current IF V = 4.1 V 117 130 156 mA EL Power Supply Current IEL VEL = 110 VAC, 400 Hz - - 5.0 mA DISPLAY CHARACTER ADDRESS CODE Display Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DD RAM Address 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F DD RAM Address 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F Document Number: 37490 1 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay INTERFACE PIN FUNCTION PIN NO. SYMBOL FUNCTION 1 VSS Ground 2 VDD Supply voltage for logic 3 V0 Contrast adjustment (variable) 4 RS H: data / L: instruction code 5 R/W H: read (MPU module) / L: write (MPU module) 6 E H, H L chip enable signal 7 DB0 Data bus line 8 DB1 Data bus line 9 DB2 Data bus line 10 DB3 Data bus line 11 DB4 Data bus line 12 DB5 Data bus line 13 DB6 Data bus line 14 DB7 Data bus line 15 A Power supply for backlight (+) 16 K Power supply for backlight (-) DIMENSIONS in millimeters 80.0 0.5 71.2 12.45 56.2 (AA) 7.55 66.0 (VA) 16 x O 1.0 PTH 8.6 16 A K 31.0 11.5 (AA) 25.2 16.0 (VA) 2.5 1.8 1 36.0 0.5 13.2 max. P2.54 x 15 = 38.1 18.3 7.86 2 12.55 5.7 10.3 4.95 A K 40.55 2.5 75.0 LED B/L 3.55 2.95 1.6 4 x O 2.5 PTH 4 x O 5.0 PAD 0.6 0.6 0.7 0.65 5.55 0.4 5.95 0.55 The non-specified tolerance of dimension is 0.3 mm. DOT SIZE SCALE 5/1 Document Number: 37490 2 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 1.Module Classification Information LCD -016 N 002 B 1 2 3 4 5 -Y Y H 6 7 -ET 8 9 1. BrandVishay Intertechnology, Inc. 2. Horizontal Format: 16 characters 3. Display TypeNCharacter Type, HGraphic Type, YTAB Type 4. Vertical Format: 2 Lines 5. Model serials no.: B NWithout backlight 6. Backlight Type BEL, Blue green DEL, Green WEL, White MEL, Yellow Green FCCFL, White YLED, Yellow Green GLED, Green TLED, White ALED, Amber RLED, Red OLED, Orange GLED, Green EDIP LED, Yellow Green PLED, Blue HDIP LED,Amber XLED, Dual color IDIP LED, Red CLED, Full color 7. LCD Mode BTN Positive, Gray NTN Negative, LVA Negative H HTN Positive, Gray IHTN Negative, Black UHTN Negative, Blue MSTN Negative, Blue GSTN Positive, Gray YSTN Positive, Yellow Green AReflective, N.T, 6:00 8. LCD Polarizer Type/ DReflective, N.T, 12:00 GReflective, W. T, 6:00 Temperature range/ View direction SLED, High light White LLED, Full color JDIP LED,Blue KDIP LED,White JReflective, W. T, 12:00 BTransflective, N.T,6:00 ETransflective, N.T.12:00 VFSTN Negative, Blue TFSTN Negative, Black DFSTN Negative (Double film) FFSTN Positive KFSC Negative SFSC Positive EISTN Negative, Black CCSTN Negative, Black AASTN Negative, Black HTransflective, W.T,6:00 KTransflective, W.T,12:00 CTransmissive, N.T,6:00 FTransmissive, N.T,12:00 ITransmissive, W. T, 6:00 LTransmissive, W.T,12:00 9. Special Code ET: English and European standard font Note: Compliant with the ROHS Directions and regulations Document Number: 37490 3 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 2.Precautions in use of LCD Modules (1)Avoid applying excessive shocks to the module or making any alterations or modifications to it. (2)Don't make extra holes on the printed circuit board, modify its shape or change the components of LCD module. (3)Don't disassemble the LCM. (4)Don't operate it above the absolute maximum rating. (5)Don't drop, bend or twist LCM. (6)Soldering: only to the I/O terminals. (7)Storage: please storage in anti-static electricity container and clean environment. (8) Supplier had the right to change the passive components, including R3,R6 & backlight adjust resistors. (Resistors, capacitors and other passive components will have different appearance and color caused by the different supplier.) (9)Supplier has the right to change the PCB Rev. (In order to satisfy the supplying stability, management optimization and the best product performance...etc, under the premise of not affecting the electrical characteristics and external dimensions, Vishay has the right to modify the version.) Document Number: 37490 4 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 3.General Specification Item Dimension Unit 16 characters x 2Lines 80.0 x 36.0 x 13.2 (MAX) mm View area 66.0 x 16.0 mm Active area 56.20 x 11.5 mm Dot size 0.55 x 0.65 mm Dot pitch 0.60 x 0.70 mm Character size 2.95 x 5.55 mm Character pitch 3.55 x 5.95 mm Number of Characters Module dimension LCD type STN Positive, Yellow Green Transflective (In LCD production, It will occur slightly color difference. We can only guarantee the same color in the same batch.) Duty 1/16 View direction 6 o'clock Backlight Type LED Yellow Green IC ST7066U Document Number: 37490 5 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 4.Absolute Maximum Ratings Item Symbol Min Typ Max Unit Operating Temperature TOP -20 +70 Storage Temperature TST -30 +80 Input Voltage VI VSS VDD V Supply Voltage For Logic VDD-VSS -0.3 7 V Supply Voltage For LCD VDD-Vo -0.3 13 V Document Number: 37490 6 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 5.Electrical Characteristics Item Supply Voltage For Logic Symbol Condition Min Typ Max Unit VDD-VSS 4.5 5.0 5.5 V Ta=-20 5.2 V Ta=25 3.6 3.7 3.8 V Ta=70 3.2 V Supply Voltage For LCD VDD-V0 *Note Input High Volt. VIH 0.7 VDD VDD V Input Low Volt. VIL Vss 0.6 V Output High Volt. VOH 3.9 VDD V Output Low Volt. VOL 0 0.4 V Supply Current IDD VDD=5.0V 1.0 1.2 1.5 mA * Note: Please design the VOP adjustment circuit on customer's main board Vdd VR 10K~20K Vo LCM Module VSS Document Number: 37490 7 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 6.Optical Characteristics Item Symbol Condition Min Typ Max Unit CR2 0 20 = 180 CR2 0 40 = 0 CR2 0 30 = 90 CR2 0 30 = 270 CR 3 T rise 150 200 ms T fall 150 200 ms View Angle Contrast Ratio Response Time Definition of Operation Voltage (Vop) Intensity 100 Definition of Response Time ( Tr , Tf ) Non-selected Condition Selected Wave Selected Condition Non-selected Condition Intensity Non-selected Wave 10% Cr Max Cr = Lon / Loff Vop 90% 100% Driving Voltage(V) Tr Tf Positive type [positive type] Conditions : Operating Voltage : Vop Viewing Angle() : 0 0 Frame Frequency : 64 HZ Driving Waveform : 1/N duty , 1/a bias Definition of viewing angle(CR2) b f l = 180 r = 90 = 270 = 0 Document Number: 37490 8 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 7.Interface Pin Function Pin No. Symbol Level Description 1 VSS 0V Ground 2 VDD 5.0V 3 VO 4 RS H/L H: DATA, L: Instruction code 5 R/W H/L H: Read(MPUModule) L: Write(MPUModule) 6 E H,HL 7 DB0 H/L Data bus line 8 DB1 H/L Data bus line 9 DB2 H/L Data bus line 10 DB3 H/L Data bus line 11 DB4 H/L Data bus line 12 DB5 H/L Data bus line 13 DB6 H/L Data bus line 14 DB7 H/L Data bus line 15 A Power supply for B/L(+) 16 K Power supply for B/L(-) Supply Voltage for logic (Variable) Contrast Adjustment Chip enable signal Document Number: 37490 9 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 8.Contour Drawing &Block Diagram 80.0 0.5 4.95 71.2 56.2(AA) 12.45 66.0(VA) 13.2Max A 31.0 K 8.6 18.3 2 16- 1.0 PTH 2.5 P2.54*15=38.1 1.8 36.0 0.5 25.2 16.0(VA) 11.5(AA) 5.7 10.3 12.55 7.55 7.86 A K 40.55 2.5 75.0 4- 2.5 PTH 4- 5.0 PAD 1.6 LED B/L 3.55 2.95 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Vss Vdd Vo RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 A K 0.6 0.4 5.95 5.55 0.7 0.65 0.6 0.55 The non-specified tolerance of dimension is 0.3mm. DOT SIZE SCALE 5/1 Document Number: 37490 10 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 9 .Character Generator ROM Pattern Table.2 Upper 4 bit Lower 4 bit LLLL LLLH LLHL LLHH LHLL LHLH LHHL LHHH HLLL HLLH HLHL HLHH HHLL HHLH HHHL HHHH LLLL CG RAM (1) LLLH CG RAM (2) LLHL CG RAM (3) LLHH CG RAM (4) LHLL CG RAM (5) LHLH CG RAM (6) LHHL CG RAM (7) LHHH CG RAM (8) HLLL CG RAM (1) HLLH CG RAM (2) HLHL CG RAM (3) HLHH CG RAM (4) HHLL CG RAM (5) HHLH CG RAM (6) HHHL CG RAM (7) HHHH CG RAM (8) Document Number: 37490 11 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 10.Reliability Content of Reliability Test (Wide temperature, -20~70) Environmental Test Test Item High Temperature storage Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature/ Humidity storage Thermal shock resistance Content of Test Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (Voltage & Current) and the thermal stress to the element for a long time. Endurance test applying the electric stress under low temperature for a long time. The module should be allowed to stand at 60 ,90%RH max For 96hrs under no-load condition excluding the polarizer, Then taking it out and drying it at normal temperature. The sample should be allowed stand the following 10 cycles of operation -20 25 70 30min 1 cycle 5min Test Condition 80 200hrs -30 200hrs Note 2 1,2 70 200hrs ---- -20 200hrs 1 60,90%RH 96hrs 1,2 -20/70 10 cycles ---- 30min Total fixed amplitude : 1.5mm Vibration Frequency : Endurance test applying the vibration during 3 Vibration test 10~55Hz transportation and using. One cycle 60 seconds to 3 directions of X,Y,Z for Each 15 minutes VS=800V,RS=1.5k Endurance test applying the electric stress to the Static electricity test ---- terminal. CS=100pF 1 time Note1: No dew condensation to be observed. Note2: The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after remove from the test chamber. Note3: The packing have to including into the vibration testing. Document Number: 37490 12 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 11.Backlight Information Specification PARAMETER SYMBOL MIN TYP MAX UNIT TEST CONDITION Supply Current ILED 117 130 156 mA V=4.1V Supply Voltage V 3.9 4.1 4.3 V Reverse Voltage VR 8 V IV 216 270 CD/M2 ILED=130mA Wave Length p 569 570 573 nm Life Time 100000 Luminance (Without LCD) ILED=130mA ILED130mA Hr. 25,50-60%RH Color Yellow Green Note: The LED of B/L is drive by current only, drive voltage is for reference only. drive voltage can make driving current under safety area (current between minimum and maximum). 2.Drive from pin15,pin16 R R A K B/L LCM ill never get Vee output from pin15) Document Number: 37490 13 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 12.Inspection specification NO Item Criterion AQL Missing vertical, horizontal segment, segment contrast defect. Missing character , dot or icon. Display malfunction. 01 Electrical Testing No function or no display. Current consumption exceeds product specifications. LCD viewing angle defect. Mixed product types. 0.65 Contrast defect. Black or 02 2.1 White and black spots on display 0.25mm, no more than white spots on three white or black spots present. LCD (display 2.2 Densely spaced: No more than two spots or lines within 3mm only) 3.1 Round type : As following drawing SIZE =( x + y ) / 2 0.10 LCD black 03 04 Accept no dense 2 0.200.25 1 0.25 0 2.5 Acceptable Q TY Accept no dense 2 L2.5 0.03W0.05 --- 0.05W As round type Size Acceptable Q TY If bubbles are visible, Polarizer bubbles Acceptable Q TY 0.100.20 spots, white spots, 3.2 Line type : (As following drawing) contamination Length Width (non-display) W0.02 --L3.0 0.02W0.03 judge using black spot specifications, not easy to find, must check in specify direction. 2.5 0.20 Accept no dense 0.200.50 3 0.501.00 2 1.00 0 Total Q TY 3 2.5 2.5 Document Number: 37490 14 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay NO Item Criterion 05 Follow NO.3 LCD black spots, white spots, contamination Scratches Symbols Define: x: Chip length AQL y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length: 6.1 General glass chip : 6.1.1 Chip on panel surface and crack between panels: 06 Chipped glass z: Chip thickness y: Chip width x: Chip length Z1/2t Not over viewing area x1/8a 1/2tz2t Not exceed 1/3k x1/8a 2.5 If there are 2 or more chips, x is total length of each chip. 6.1.2 Corner crack: z: Chip thickness y: Chip width x: Chip length Z1/2t Not over viewing area x1/8a 1/2tz2t Not exceed 1/3k x1/8a If there are 2 or more chips, x is the total length of each chip. Document Number: 37490 15 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com NO Item Vishay Criterion AQL Symbols : x: Chip length y: Chip width z: Chip thickness k: Seal width t: Glass thickness a: LCD side length L: Electrode pad length 6.2 Protrusion over terminal : 6.2.1 Chip on electrode pad : y: Chip width y0.5mm x: Chip length x1/8a z: Chip thickness 0 zt 6.2.2 Non-conductive portion: 06 Glass crack 2.5 y: Chip width x: Chip length z: Chip thickness y L x1/8a 0 zt If the chipped area touches the ITO terminal, over 2/3 of the ITO must remain and be inspected according to electrode terminal specifications. If the product will be heat sealed by the customer, the alignment mark not be damaged. 6.2.3 Substrate protuberance and internal crack. y: width y1/3L x: length xa Document Number: 37490 16 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay NO Item Criterion AQL 07 Cracked glass The LCD with extensive crack is not acceptable. 2.5 Backlight elements 8.1 Illumination source flickers when lit. 8.2 Spots or scratched that appear when lit must be judged. Using LCD spot, lines and contamination standards. 8.3 Backlight doesn't light or color wrong. 0.65 2.5 9.1 Bezel may not have rust, be deformed or have fingerprints, stains or other contamination. 9.2 Bezel must comply with job specifications. 2.5 10.1 COB seal may not have pinholes larger than 0.2mm or 2.5 contamination. 10.2 COB seal surface may not have pinholes through to the IC. 10.3 The height of the COB should not exceed the height indicated in the assembly diagram. 2.5 0.65 08 09 10 Bezel PCBCOB 0.65 0.65 10.4 There may not be more than 2mm of sealant outside the seal area on the PCB. And there should be no more than three places. 10.5 No oxidation or contamination PCB terminals. 2.5 10.6 Parts on PCB must be the same as on the production characteristic chart. There should be no wrong parts, missing parts or excess parts. 10.7 The jumper on the PCB should conform to the product 0.65 characteristic chart. 10.8 If solder gets on bezel tab pads, LED pad, zebra pad or screw hold pad, make sure it is smoothed down. 10.9 The Scraping testing standard for Copper Coating of PCB 2.5 0.65 2.5 2.5 X Y 11 Soldering X * Y<=2mm2 11.1 No un-melted solder paste may be present on the PCB. 11.2 No cold solder joints, missing solder connections, oxidation or icicle. 2.5 2.5 11.3 No residue or solder balls on PCB. 11.4 No short circuits in components on PCB. 2.5 0.65 Document Number: 37490 17 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com NO 12 Item General appearance Vishay Criterion AQL 12.1 No oxidation, contamination, curves or, bends on interface 2.5 Pin (OLB) of TCP. 12.2 No cracks on interface pin (OLB) of TCP. 12.3 No contamination, solder residue or solder balls on product. 12.4 The IC on the TCP may not be damaged, circuits. 0.65 2.5 2.5 12.5 The uppermost edge of the protective strip on the interface pin must be present or look as if it cause the interface pin to sever. 12.6 The residual rosin or tin oil of soldering (component or chip component) is not burned into brown or black color. 2.5 12.7 Sealant on top of the ITO circuit has not hardened. 12.8 Pin type must match type in specification sheet. 12.9 LCD pin loose or missing pins. 12.10 Product packaging must the same as specified on packaging 2.5 0.65 0.65 0.65 specification sheet. 12.11 Product dimension and structure must conform to product specification sheet. 12.12 Visual defect outside of VA is not considered to be rejection. 2.5 0.65 0.65 Document Number: 37490 18 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 LCD-016N002B-YYH-ET www.vishay.com Vishay 13.Material List of Components for RoHS 1. Declaration that all of or part of products (with the mark "N" in code), including, but not limited to, the LCM, accessories or packages, manufactured and/or delivered to your company (including your subsidiaries and affiliated company) directly or indirectly by our company (including our subsidiaries or affiliated companies) do not intentionally contain any of the substances listed in all applicable EU directives and regulations, including the following substances. Exhibit AThe Harmful Material List Material (Cd) (Pb) (Hg) (Cr6+) PBBs PBDEs Limited 100 1000 1000 1000 1000 1000 Value ppm ppm ppm ppm ppm ppm Above limited value is set up according to RoHS. 2.Process for RoHS requirement (1) Use the Sn/Ag/Cu soldering surfacethe surface of Pb-free solder is rougher than we used before. (2) Heat-resistance temp. Reflow250 ,30 seconds Max. Connector soldering wave or hand soldering320 , 10 seconds max. (3) Temp. curve of reflow, max. Temp.2355 Recommended customer's soldering temp. of connector280 , 3 seconds. 14.Recommendable Storage 1. Place the panel or module in the temperature 25C5C and the humidity below 65% RH 2. Do not place the module near organics solvents or corrosive gases. 3. Do not crush, shake, or jolt the module. Document Number: 37490 19 For technical questions, contact: displays@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Revision: 06-Feb-15 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000