L79L Negative voltage regulators Datasheet - production data Description The L79L series of three-terminal negative regulators employ internal current limiting and thermal shutdown, making them essentially indestructible. If adequate heat-sink is provided, they can deliver up to 100 mA output current. They are intended as fixed voltage regulators in a wide range of applications including local or oncard regulation for elimination of noise and distribution problems associated with single-point regulation. In addition, they can be used with power pass elements to make high-current voltage regulators. The L79L series used as Zener diode/resistor combination replacement, offers an effective output impedance improvement of typically two orders of magnitude, along with lower quiescent current and lower noise. Features Output current up to 100 mA Output voltages of -5; -8;-12; -15 V Thermal overload protection Short-circuit protection No external components are required Output tolerance + 4% December 2017 DocID2511 Rev 19 This is information on a product in full production. 1/23 www.st.com Contents L79L Contents 1 Diagram ............................................................................................ 3 2 Pin configuration ............................................................................. 4 3 Maximum ratings ............................................................................. 5 4 5 Electrical characteristics ................................................................ 6 Package information ....................................................................... 9 5.1 TO-92 package information ............................................................... 9 5.2 TO-92 packing information .............................................................. 10 5.3 TO-92 Ammopak packing information ............................................. 12 5.4 SO-8 package information .............................................................. 14 5.5 SO-8 packing information ................................................................ 16 5.6 SOT-89 package information .......................................................... 17 5.7 SOT-89 packing information............................................................ 20 6 Ordering information..................................................................... 21 7 Revision history ............................................................................ 22 2/23 DocID2511 Rev 19 L79L 1 Diagram Diagram Figure 1: Schematic diagram DocID2511 Rev 19 3/23 Pin configuration 2 L79L Pin configuration Figure 2: Pin connection (top view, bottom view for TO-92) Figure 3: Test circuit 4/23 DocID2511 Rev 19 L79L 3 Maximum ratings Maximum ratings Table 1: Absolute maximum ratings Symbol Parameter VI DC input voltage IO Output current PD Value Unit VO = -5 to -9 V -30 VO = -12 to -15 V -35 V 100 mA Internally limited Power dissipation TSTG Storage temperature range TOP Operating junction temperature range (1) -40 to 150 For L79LXXAC 0 to 125 For L79LXXAB -40 to 125 mW C C Notes: (1) Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically communed to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heat-sinking. The external dimensions are the same as for the standard SO-8. Table 2: Thermal data Symbol RthJC RthJA Parameter Thermal resistance junction-case (max.) Thermal resistance junction-ambient (max.) SO-8 TO-92 20 55 (1) 200 SOT-89 Unit 15 C/W 115 C/W Notes: (1) Considering 6 cm2 of copper Board heat-sink. DocID2511 Rev 19 5/23 Electrical characteristics 4 L79L Electrical characteristics Refer to the test circuits, VI = - 10 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, TJ = 0 to 125 C for L79L05AC, TJ = -40 to 125 C for L79L05AB, unless otherwise specified. Table 3: Electrical characteristics of L79L05AC and L79L05AB Symbol VO VO Parameter Output voltage Test conditions Min. Typ. Max. Unit TJ = 25 C -4.8 -5 -5.2 V IO = 1 to 40 mA, VI = -7 to -20 V 4.75 5.25 IO = 1 to 70 mA, VI = -10 V 4.75 5.25 Output voltage VO Line regulation VO Load regulation V VI = -7 to -20 V, TJ = 25 C 150 VI = -8 to -20 V, TJ = 25 C 100 IO = 1 to 100 mA, TJ = 25 C 60 IO = 1 to 40 mA, TJ = 25 C 30 TJ = 25 C 6 mA TJ = 125 C 5.5 mA Id Quiescent current Id Quiescent current change IO = 1 to 40 mA 0.1 VI = -8 to -20 V 1.5 eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C SVR Supply voltage rejection VI = -8 to -18 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Dropout voltage 41 mV mV mA 40 V 49 dB 1.7 V Refer to the test circuits, VI = - 14 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, TJ = 0 to 125 C for L79L08AC TJ = -40 to 125 C for L79L08AB, unless otherwise specified. Table 4: Electrical characteristics of L79L08AC and L79L08AB Symbol 6/23 Parameter VO Output voltage VO Output voltage VO Line regulation VO Load regulation Id Quiescent current Id Quiescent current change eN Output noise voltage Test conditions Min. Typ. Max. Unit TJ = 25 C 7.68 -8 8.32 V IO = 1 to 40 mA, VI = -10.5 to -23 V -7.6 -8.4 IO = 1 to 70 mA, VI = -14 V -7.6 -8.4 V VI = -10.5 to -23 V, TJ = 25 C 175 VI = -11 to -23 V, TJ = 25 C 125 IO = 1 to 100 mA, TJ = 25 C 80 IO = 1 to 40 mA, TJ = 25 C 40 TJ = 25 C 6 mA TJ = 125 C 5.5 mA IO = 1 to 40 mA 0.1 VI = -11 to -23 V 1.5 B = 10 Hz to 100 kHz, TJ = 25 C DocID2511 Rev 19 60 mV mV mA V L79L Electrical characteristics Symbol Parameter SVR Supply voltage rejection Vd Dropout voltage Test conditions Min. Typ. Max. Unit VI = -12 to -23 V, f = 120 Hz, IO = 40 mA, TJ = 25 C 37 45 dB 1.7 V Refer to the test circuits, VI = - 19 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, TJ = 0 to 125 C for L79L12AC, TJ = -40 to 125 C for L79L12AB, unless otherwise specified. Table 5: Electrical characteristics of L79L12AC and L79L12AB Symbol VO VO Parameter Test conditions Min. Typ. Max. Unit -12 -12.5 V Output voltage TJ = 25C -11.5 Output voltage IO = 1 to 40 mA, VI = -14.5 to -27 V -11.4 -12.6 IO = 1 to 70 mA, VI = -19 V -11.4 -12.6 VO Line regulation VO Load regulation V VI = -14.5 to -27 V, TJ = 25 C 250 VI = -16 to -27 V, TJ = 25 C 200 IO = 1 to 100 mA, TJ = 25 C 100 IO = 1 to 40 mA, TJ = 25 C 50 TJ = 25 C 6.5 mA TJ = 125 C 6 mA Id Quiescent current Id Quiescent current change IO = 1 to 40 mA 0.1 VI = -16 to -27 V 1.5 eN Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C SVR Supply voltage rejection VI = -15 to -25 V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Dropout voltage 37 mV mV mA 80 V 42 dB 1.7 V Refer to the test circuits, VI = - 23 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, TJ = 0 to 125 C for L79L15AC, TJ = -40 to 125 C for L79L15AB, unless otherwise specified. Table 6: Electrical characteristics of L79L15AC and L79L15AB Symbol Parameter Test conditions Min. Typ. Max. Unit -15 -15.6 V VO Output voltage TJ = 25C -14.4 VO Output voltage IO = 1 to 40 mA, VI = -17.5 to -30 V -14.25 -15.75 IO = 1 to 70 mA, VI = -23 V -14.25 -15.75 VO Line regulation VO Load regulation Id Quiescent current Id Quiescent current change V VI = -17.5 to -30 V, TJ = 25 C 300 VI = -20 to -30 V, TJ = 25 C 250 IO = 1 to 100 mA, TJ = 25 C 150 IO = 1 to 40 mA, TJ = 25 C 75 TJ = 25 C 6.5 mA TJ = 125 C 6 mA IO = 1 to 40 mA 0.1 VI = -20 to -30 V 1.5 DocID2511 Rev 19 mV mV mA 7/23 Electrical characteristics Symbol Parameter Test conditions Output noise voltage B = 10 Hz to 100 kHz, TJ = 25 C SVR Supply voltage rejection VI = -18.5 to -28.5.V, f = 120 Hz IO = 40 mA, TJ = 25 C Vd Dropout voltage eN 8/23 L79L DocID2511 Rev 19 Min. 34 Typ. Max. Unit 90 V 39 dB 1.7 V L79L 5 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK (R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. 5.1 TO-92 package information Figure 4: TO-92 package outline Table 7: TO-92 mechanical data mm Dim. Min. Typ. Max. A 4.32 4.95 b 0.36 0.51 D 4.45 4.95 E 3.30 3.94 e 2.41 2.67 e1 1.14 1.40 L 12.70 15.49 R 2.16 2.41 S1 0.92 1.52 W 0.41 0.56 V 5 DocID2511 Rev 19 9/23 Package information 5.2 L79L TO-92 packing information Figure 5: TO-92 tape and reel outline 10/23 DocID2511 Rev 19 L79L Package information Table 8: TO-92 tape and reel mechanical data mm Dim. Min. Typ. Max. A1 4.80 T 3.80 T1 1.60 T2 2.30 d 0.45 0.47 0.48 P0 12.50 12.70 12.90 P2 5.65 6.35 7.05 F1, F2 2.40 2.50 2.94 F3 4.98 5.08 5.48 delta H -2.00 W 17.50 18.00 19.00 W0 5.5 6.00 6.5 W1 8.50 9.00 9.25 2.00 W2 0.50 H 18.50 21 H3 0.5 1 2 H0 15.50 16.00 18.8 25.0 27.0 4.00 4.20 H1 D0 3.80 t 0.90 L 11.00 I1 3.00 delta P -1.00 O1 352 355 358 O2 28 30 32 u 44 47 50 DocID2511 Rev 19 1.00 11/23 Package information 5.3 L79L TO-92 Ammopak packing information Figure 6: TO-92 Ammopak tape and reel outline 12/23 DocID2511 Rev 19 L79L Package information Table 9: TO-92 Ammopak tape and reel mechanical data mm Dim. Min. Typ. Max. A1 4.80 T 3.80 T1 1.60 T2 2.30 d 0.45 0.47 0.48 P0 12.50 12.70 12.90 P2 5.65 6.35 7.05 F1, F2 2.40 2.50 2.94 F3 4.98 5.08 5.48 delta H -2.00 W 17.50 18.00 19.00 W0 5.5 6.00 6.5 W1 8.50 9.00 9.25 2.00 W2 0.50 H 18.50 21 H3 0.5 1 2 H0 15.50 16.00 18.8 25.0 27.0 4.00 4.20 H1 D0 3.80 t 0.90 L 11.00 I1 3.00 delta P -1.00 DocID2511 Rev 19 1.00 13/23 Package information 5.4 L79L SO-8 package information Figure 7: SO-8 package outline 14/23 DocID2511 Rev 19 L79L Package information Table 10: SO-8 mechanical data mm Dim. Min. Typ. A Max. 1.75 A1 0.10 0.25 A2 1.25 b 0.31 0.51 b1 0.28 0.48 c 0.10 0.25 c1 0.10 0.23 D 4.80 4.90 5.00 E 5.80 6.00 6.20 E1 3.80 3.90 4.00 e 1.27 h 0.25 0.50 L 0.40 1.27 L1 1.04 L2 0.25 k 0 ccc 8 0.10 Figure 8: SO-8 recommended footprint (dimensions are in mm) DocID2511 Rev 19 15/23 Package information 5.5 L79L SO-8 packing information Figure 9: SO-8 tape and reel dimensions Table 11: SO-8 tape and reel mechanical data Dim. mm Min. Typ. A 330 C 12.8 D 20.2 N 60 T 16/23 Max. 13.2 - 22.4 Ao 8.1 Bo 5.5 5.9 Ko 2.1 2.3 Po 3.9 4.1 P 7.9 8.1 DocID2511 Rev 19 8.5 L79L 5.6 Package information SOT-89 package information Figure 10: SOT-89 package outline DocID2511 Rev 19 17/23 Package information L79L Table 12: SOT-89 mechanical data mm Dim. Min. Max. A 1.40 1.60 B 0.44 0.56 B1 0.36 0.48 C 0.35 0.44 C1 0.35 0.44 D 4.40 4.60 D1 1.62 1.83 D3 18/23 Typ. 0.90 E 2.29 2.60 e 1.42 1.57 e1 2.92 3.07 H 3.94 4.25 H1 2.70 3.10 K 1 8 L 0.89 120 R 0.25 90 DocID2511 Rev 19 L79L Package information Figure 11: SOT-89 recommended footprint DocID2511 Rev 19 19/23 Package information 5.7 L79L SOT-89 packing information Figure 12: SOT-89 carrier tape outline Table 13: SOT-89 carrier tape mechanical data mm Dim. 20/23 Value Tolerance Ao 4.91 0.10 Bo 4.52 0.10 Ko 1.90 0.10 F 5.50 0.10 E 1.75 0.10 W 12 0.30 P2 2 0.10 Po 4 0.10 P1 8 0.10 T 0.30 0.10 D O 1.55 0.05 D1 O 1.60 0.10 DocID2511 Rev 19 L79L 6 Ordering information Ordering information Table 14: Ordering information SO-8 TO-92 (bag) TO-92 (Ammopak) L79L05ABD13TR L79L05ACZ L79L05ABZAP L79L05ACD13TR L79L08ACZAP TO-92 (tape and reel) SOT-89 Output voltage (V) L79L05ABUTR -5 L79L05ACZ-TR L79L05ACUTR -5 L79L12ACZ-TR L79L12ACUTR -12 L79L08ACD13TR L79L12ACD13TR -8 L79L15ABD13TR -15 L79L15ACD13TR L79L15ACUTR DocID2511 Rev 19 -15 21/23 Revision history 7 L79L Revision history Table 15: Document revision history Date 22/23 Revision Changes 14-Mar-2005 9 Add Tape and Reel for TO-92. 15-Mar-2005 10 Add note on Table 3. 23-Dec-2005 11 Mistake on ordering Table in Header. 12-Sep-2006 12 Order codes updated. 25-Jul-2007 13 Pin connection for SOT-89 updated on Figure 2. 04-Dec-2007 14 Modified: Table 14. 14-Jul-2008 15 Modified: Table 14 on page 24. 29-Jul-2009 16 Modified: Table 14 on page 24. 17-Apr-2014 17 Part numbers L79LxxAB, L78LxxAC, L78LxxC changed to L79L. Removed Table 1: Device summary. Updated the features and description in cover page. Updated Figure 1: Schematic diagram, Table 1: Absolute maximum ratings and Table 14: Order codes. Added Section 5: Packaging mechanical data. Minor text changes. 12-Feb-2016 18 Updated Section 5: Package information. Minor text changes. 06-Dec-2017 19 Updated features in cover page. DocID2511 Rev 19 L79L IMPORTANT NOTICE - PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST's terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers' products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. (c) 2017 STMicroelectronics - All rights reserved DocID2511 Rev 19 23/23