SSM3J35CT TOSHIBA Field-Effect Transistor Silicon P-Channel MOS Type SSM3J35CT High-Speed Switching Applications Analog Switch Applications Unit: mm * 1.2-V drive * Low ON-resistance : Ron = 44 (max) (@VGS = -1.2 V) : Ron = 22 (max) (@VGS = -1.5 V) : Ron = 11 (max) (@VGS = -2.5 V) : Ron = 8 (max) (@VGS = -4.0 V) Absolute Maximum Ratings (Ta = 25C) Characteristics Symbol Rating Unit Drain-source voltage VDSS -20 V Gate-source voltage VGSS 10 V DC ID -100 Pulse IDP -200 Drain current Drain power dissipation mA PD (Note 1) 100 mW Channel temperature Tch 150 C Storage temperature Tstg -55 to 150 C CST3 JEDEC - JEITA Note: Using continuously under heavy loads (e.g. the application of high TOSHIBA 2-1J1B temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the Weight: 0.75 mg (typ.) reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Mounted on an FR4 board (10 mm x 10 mm x 1.0 mm, Cu Pad: 100 mm2 ) Marking (top view) Polarity mark Pin Assignment (top view) Equivalent Circuit (top view) Polarity mark (on the top) 3 1 S3 3 1 2 2 1. Gate 2. Source 3. Drain *Electrodes: on the bottom Start of commercial production 2008-03 1 2015-09-29 SSM3J35CT Electrical Characteristics (Ta = 25C) Characteristics Symbol Test Condition Min Typ. Max Unit IGSS VGS = 10 V, VDS = 0 V 10 A V (BR) DSS ID = -0.1 mA, VGS = 0 V -20 V IDSS VDS = -20 V, VGS = 0 V -1 A Gate threshold voltage Vth VDS = -3 V, ID = -1 mA -0.4 -1.0 V Forward transfer admittance |Yfs| VDS = -3 V, ID = -50 mA (Note 2) 77 mS ID = -50 mA, VGS = -4 V (Note 2) 4.3 8 ID = -50 mA, VGS = -2.5 V (Note 2) 5.6 11 ID = -5 mA, VGS = -1.5 V (Note 2) 8.2 22 ID = -2 mA, VGS = -1.2 V (Note 2) 11 44 12.2 6.5 10.4 175 251 0.83 1.2 Gate leakage current Drain-source breakdown voltage Drain cutoff current Drain-source ON-resistance RDS (ON) Input capacitance Ciss Reverse transfer capacitance Crss Output capacitance Coss VDS = -3 V, VGS = 0 V, f = 1 MHz Turn-on time ton Turn-off time toff VDD = -3 V, ID = -50 mA, VGS = 0 to -2.5 V VDSF ID = 100 mA, VGS = 0 V Switching time Drain-source forward voltage (Note 2) pF ns V Note 2: Pulse test Switching Time Test Circuit (a) Test Circuit (b) VIN 0V 10% OUT 0 IN 90% -2.5 V 50 -2.5V 10 s RL VDD (c) VOUT VDD = -3 V Duty 1% VIN: tr, tf < 5 ns (Zout = 50 ) Common Source Ta = 25C VDS (ON) 90% 10% VDD tr ton tf toff Usage Considerations Let Vth be the voltage applied between gate and source that causes the drain current (ID) to below (-1 mA for the SSM3J35CT). Then, for normal switching operation, VGS(on) must be higher than Vth, and VGS(off) must be lower than Vth. This relationship can be expressed as: VGS(off) < Vth < VGS(on). Take this into consideration when using the device. Handling Precaution When handling individual devices that are not yet mounted on a circuit board, make sure that the environment is protected against electrostatic discharge. Operators should wear antistatic clothing, and containers and other objects that come into direct contact with devices should be made of antistatic materials. 2 2015-09-29 SSM3J35CT ID - VDS -250 ID - VGS -1000 Common Source VDS = -3 V Ta = 25C -4 V (mA) -100 (mA) -200 -2.5 V -150 Drain current ID Drain current ID Common Source -1.8 V -100 -1.5 V -50 VGS=-1.2 V -1.5 -1 -0.5 Drain-source voltage VDS 25C -25C -1 -0.1 -0.01 0 0 0 Ta = 100C -10 -2 (V) -1 -3 Gate-source voltage VGS RDS (ON) - VGS (V) RDS (ON) - VGS 20 15 Common Source Common Source ID = -5 mA ID = -50 mA Drain-source ON-resistance RDS (ON) () Drain-source ON-resistance RDS (ON) () -2 15 10 25C Ta=100C 5 10 25C Ta=100C 5 -25C -25C 0 0 -2 -4 -6 Gate-source voltage VGS 0 -10 -8 0 (V) -2 -4 -10 -8 Gate-source voltage VGS (V) RDS (ON) - Ta RDS (ON) - ID 20 20 Common Source Common Source Ta = 25C Drain-source ON-resistance RDS (ON) () Drain-source ON-resistance RDS (ON) () -6 15 VGS = -1.2 V 10 -1.5 V -2.5 V 5 -4 V 0 -1 -10 Drain current ID -100 -1.5 V, -5 mA 10 (mA) -2.5 V, -50 mA -4 V, -50 mA 5 0 -50 -1000 VGS =-1.2 V, ID=-2 mA 15 0 50 100 150 Ambient temperature Ta (C) 3 2015-09-29 SSM3J35CT Vth - Ta |Yfs| - ID (mS) -1 ID = -1 mA VDS = -3 V -0.8 Forward transfer admittance |Yfs| Gate threshold voltage Vth (V) Common Source -0.6 -0.4 -0.2 0 -50 0 100 50 150 1000 100 10 Common Source VDS = -3 V Ta = 25C 1 -1 -10 Ambient temperature Ta (C) Drain current ID IDR - VDS -1000 -100 (mA) C - VDS 1000 100 VGS = 0 V 100 D G Capacitance C (pF) Drain reverse current IDR (mA) Common Source IDR 10 S 25C 1 Ta=100C 0.1 -25C 0.01 0 0.2 0.4 0.6 0.8 1 Drain-source voltage VDS 1.2 10 Ciss Coss Crss Common Source VGS = 0 V f = 1 MHz Ta = 25C 1 -0.1 1.4 (V) -1 -10 Drain-source voltage VDS (ns) Common Source VDD = -3 V VGS = 0 to -2.5 V Ta = 25C toff Switching time t 1000 tf 100 ton tr 10 -0.1 (V) PD - Ta Drain Power Dissipation PD (mW) t - ID 10000 -100 250 Mounted on FR4 board (10 mm x 10 mm x 1.0 mm, Cu Pad: 100 mm2 ) 200 150 100 50 0 -1 -10 Drain current ID -100 -1000 0 20 40 60 80 100 120 140 160 Ambient temperature Ta (C) (mA) 4 2015-09-29 SSM3J35CT RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * PRODUCT IS NEITHER INTENDED NOR WARRANTED FOR USE IN EQUIPMENTS OR SYSTEMS THAT REQUIRE EXTRAORDINARILY HIGH LEVELS OF QUALITY AND/OR RELIABILITY, AND/OR A MALFUNCTION OR FAILURE OF WHICH MAY CAUSE LOSS OF HUMAN LIFE, BODILY INJURY, SERIOUS PROPERTY DAMAGE AND/OR SERIOUS PUBLIC IMPACT ("UNINTENDED USE"). Except for specific applications as expressly stated in this document, Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. IF YOU USE PRODUCT FOR UNINTENDED USE, TOSHIBA ASSUMES NO LIABILITY FOR PRODUCT. For details, please contact your TOSHIBA sales representative. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the applicable export laws and regulations including, without limitation, the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA ASSUMES NO LIABILITY FOR DAMAGES OR LOSSES OCCURRING AS A RESULT OF NONCOMPLIANCE WITH APPLICABLE LAWS AND REGULATIONS. 5 2015-09-29