Technical Document LCD Specification LCD Group LQ057Q3DG02 LCD Module Product Specification June 2009 QVGA module with 400 nits brightness and 550:1 contrast. An LED backlight along with high-purity color filters give excellent color reproduction. Module carries Sharp's Strong 2 Rating for temperature, shock tolerance, and brightness and contrast. Non-touch-panel version of LQ057Q3DG01. Full Specifications Listing LD-21605A1 NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for general electronic equipment use. The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e.,aircraft, trains, automobiles, etc.) Traffic signalsGas leakage sensor breakers Alarm equipmentVarious safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Nuclear power control equipment Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication. LD-21605A2 1. Application This specification applies to color TFT-LCD module, LQ057Q3DG02. 2. Summary and Features This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit (PWB), FPC, front and back polarizer, sealed case, backlight unit. Graphics and texts can be displayed on a 320xRGBx240 dots panel with 262,144 colors by suitable control supplying from the outside. It isn't composed LED drive circuit for a backlight drive. Wide Viewing Angle technology is adopted. (The most suitable viewing angle is in the 12 o'clock direction.) By adopting an active matrix drive, a picture with high contrast is realized. Reflection due to external light is minimized through the use of a low reflection black matrix . A thin, light and compact module is accomplished through the use of COG mounting technology. Through the use of high color purity color filter and TN-normally white mode excelled in color reproducibility, an image with highly natural color reproduction is realized. High viewing angle and high brightness. An inverted video display in the vertical / horizontal directions is possible. This module is adapted to RoHS compliance. 3. Mechanical specifications table 3-1 Parameter Screen size Active area Display format Dot pitch Pixel configuration Display mode Outline dimensionNote1-1 Mass Specifications 14.4 (5.7 inch) diagonal 115.2 (H) x 86.4 (V) 320(H)x240(V) (1 pixel = R + G + B dots) 0.360 (H) x 0.360 () R,G,B Stripe configuration Normally white 144.0 (W)x104.6 (H)x12.3(D) 210 (MAX) Note 1-1 A FPC of LED and some projections are excluded. A figure of outline dimension is shown in Fig. 1. Units cm mm pixels mm mm g LD-21605A3 . Input terminal 4-1. TFT-LCD panel driving part CN1 Used connector: IMSA-9637S-33Y902 (IRISO ELECTRONICS CO.,LTD.) Table 4-1 Functional table of CN1 terminals Pin No. Symbol Description Polarity GND CK Hsync Horizontal synchronous signal Negative Vsync Vertical synchronous signal Negative GND ground R0 RED data signal(LSB) R1 RED data signal R2 RED data signal R3 RED data signal R4 RED data signal R5 RED data signal(MSB) GND G0 GREEN data signal(LSB) G1 GREEN data signal G2 GREEN data signal G3 GREEN data signal G4 GREEN data signal G5 GREEN data signal(MSB) GND B0 BLUE data signal(LSB) B1 BLUE data signal B2 BLUE data signal B3 BLUE data signal B4 BLUE data signal B5 BLUE data signal(MSB) GND ground ENAB Signal to settle the horizontal display positionNote4-1 Vcc +3.3V power supply Vcc +3.3V power supply R/L U/D GND Selection signal for horizontal scanning directionNote4-2 ("L" : Normally , "H" : Right-and-Left reversal) Selection signal for vertical scanning directionNote4-2 ("H" : Normally , "L" : Up-and-Down reversal) ground GND ground ground Clock signal for sampling each data signal ground ground Positive LD-21605A4 Note 4-1The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. Don't keep ENAB "Low" during operation. Note 4-2 4-2. R/L = LU/D = H R/L = HU/D = H R/L = LU/D = L R/L = HU/D = L LED Backlight driving part (FPC1) Table 4-2 Pin No. Functional table of FPC terminals Symbol Description LED-A1 Power Supply for LED (Anode) LED-C1 Power Supply for LED (Cathode) LED-A2 Power Supply for LED (Anode) LED-C2 Power Supply for LED (Cathode) LED-A3 Power Supply for LED (Anode) LED-C3 Power Supply for LED (Cathode) LED-A4 Power Supply for LED (Anode) LED-C4 Power Supply for LED (Cathode) Suitable connector IMSA-9632S-08-AGF LD-21605A5 5. Absolute maximum ratings Table 5-1 Item Symbol Conditions Rated value Unit Remarks Input voltage VI Ta = 25C -0.3 ~ VCC +0.3 V Note 5-1 Power supply voltage VCC Ta = 25C -0.3 ~ +4.0 V Temperature for storage Tstg - -30 ~ +70 C Note 5-2,3 Temperature for operation Topr - -30 ~ +70 C Note 5-2,3,4 Note 5-1 Note 5-2 Note 5-3 Note 5-4 CK, R0R5, G0G5, B0B5, Hsync, Vsync, ENAB, R/L, U/D This rating applies to all parts of the module and should not be exceeded. Maximum wet-bulb temperature is less than 39. Condensation of dew must be avoided as electrical current leaks will occur, causing a degradation of performance specifications. The operating temperature only guarantees operation of the circuit. For contrast, speed response, and other factors related to display quality, judgment is done using the ambient temperature Ta =+25. LD-21605A6 6. Electrical characteristics 6-1. TFT-LCD panel driving section Table 6-1 Parameter +3.3V Supply voltage power suply Current dissipation Permissive input ripple Input Low voltage Input High voltage Input leak current (Low) Input leak current (High) Note 6-1 Vcc turn-on/off conditions. t110 ms 0<t2100 ms 0<t3100 ms 0<t450 ms 1000 ms<t5 Symbol Vcc Icc VRF VIL VIH IOL Min. +3.0 0 0.9Vcc Typ. +3.3 20 Max. +3.6 30 100 0.1Vcc Vcc 1 IOH 1 Ta=25 Unit Remarks V Note 6-1 mA Note 6-2 mVp-p Vcc=+3.3V V V Note 6-3 VI=0V A Note 6-3 A VI=3.3Vcc Note 6-3 Vcc 3.0V 3.0V 0.3V Signal t1 t2 0.3V t3 t4 0.3V t5 Vcc-dip conditions Vcc 1) 2.4V Vcc 3.0V 3.0V td 10 ms 2.4V 2) At Vcc 2.5V Vcc-dip conditions should also follow the Vcc turn-on/off conditions. Note 6-2 Vcc = 3.3V Max current situation : Timing ; Typical, Pattern ; All black Note 6-3 CK,R0R5,G0G5,B0B5,Hsync,Vsync,ENAB,R/L,U/D td LD-21605A7 6-2. Backlight driving section The backlight system is edge-lighting type with 20 White-LED(White Light Emitting Diode). The characteristics of White-LED are shown in the following table. (Ta = 25 deg.) Table 6-2 Parameter Min. Typ. Max. Unit Remark LED voltage - 16.0 17.5 V LED current LED current range - 20 20 mA Number of circuit strings - 4 - LED power consumption - 1.28 - W [Note 2] LED life time - 30,000 - Hour continuous operation = 20mA [Note 1] [Note 1] The LED backlight is composed by 4 strings from which 5 LED is connected with the series. The figure below shows the circuit chart. In each string, there is a ceramic capacitor for the electrostatic protection. LED-A1 LED-A3 LED-C1 LED-C3 LED-A2 LED-A4 LED-C2 LED-C4 [Note 2] Calculated value for reference ( IL x VL ) 7. Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.7 7-1. Timing characteristics Table 7-1 Parameter Symbol MIN TYP MAX Unit Remarks Clock frequency 1/Tc 6.3 7.0 MHz Duty ratio TH/T 40 50 60 % Data Setup time Tds 10 ns Hold time Tdh 10 ns Horizontal sync. Cycle TH 50.0 63.6 s signal 360 400 450 clock Pulse width THp 1 6 clock Vertical sync. Cycle TV 251 262 280 line signal frequency 1/TV 50 60 Hz Note7-1 Pulse width TVp 1 6 line Horizontal display period THd 320 320 320 clock Hsync-Clock phase difference THc 5 ns Hsync-Vsync phase difference TVh 0 320 clock Vertical display start position TVs 7 7 7 line Note7-1 In case of lower frequency, the deterioration of display quality, flicker etc., may occur. Please use this module in more than 50Hz.(1/Tv) LD-21605A8 7-2. Horizontal display position Table 7-2 Parameter symbol Min. Setup time Tes 10 Pulse width Tep 320 Hsync-Enable signal phase The 7 difference Please do not make ENAB fixation in "L". The Horizontal display start position (The) is fixed 7 clock. Enable signal Typ. 7 Max. 7 Unit ns clock clock 7-3. Vertical display position The Vertical display start position (TVs) is fixed 7 line. ENAB signal has no relation to the vertical display position. 7-4. Input Data Signals and Display Position on the screen D1,DH1 D2,DH1 D1,DH2 D2,DH2 D3,DH1 D320,DH1 D1,DH3 R G B D1,DH240 D320,DH240 Display position of input data (H,V) Remark LD-21605A9 TH THp Horizontal sync. 0.9Vcc signal Hsync Tc 0.1Vcc 0.1Vcc Tch THc Clock signal 0.1Vcc Tcl 0.1Vcc CK C1 C5 C6 C7 (Number of clock count) Tdh Tds Number of Horizontal data DataR05 G05B05 Horizintal invalid data period D1 D2 D3 D4 0.9Vcc D5 D318 D319 D320 Horizontal invalid data period THd The Data Enable signal 0.9Vcc Tes ENAB 0.1Vcc Tep TV TVp Vertical Sync 0.9Vcc signal Vsync 0.1Vcc 0.1Vcc TVh Horizontal sync 0.9Vcc signal Hsync Line1 Line2 Line7 (Number of Vertical count) TVs TVd DataR05 G05B05 Vertical invalid data period Fig 7. DH1 Input signal waveforms DH2 DH3 DH239 DH240 Vertical invalid data period LD-21605A10 () Input Signals, Basic Display Color and Gray Scale of Each Color Colors & Data signal Gray scale Gray Scale R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Basic color Gray Scale of red Gray Scale of green Gray Scale of bleu Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 x GS1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 x E E E E O E E E E Brighter GS61 1 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 O GS62 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Red GS63 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 x GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 x E E E E O E E E E Brighter GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 O GS62 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 Green GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 x GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 Darker GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 x E E E E O E E E E Brighter GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 O GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 Bleu GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 :Low level voltage 1 :High level voltage Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. 1 LD-21605A11 9. Optical characteristics Table 9-1 Parameter Viewing angle range Contrast ratio Response Rise time Fall White chromaticity Luminance Symbol 21, 22 11 12 CRmax r d x y Y Condition CR5 Optimal viewing angle Min 75 75 55 440 Typ 80 80 65 550 Max 0.263 0.279 320 30 10 0.313 0.329 400 0.363 0.379 Ta=25, VCC =+3.3V Unit Remarks (degree) Note 9-1 (degree) (degree) Note 9-2 ms ms Note 9-3 Note 9-4 cd/m2 Remarks:The optical specifications are measured 30 minute after turing LED on and in a dark room or equivalent condition, according to the method shown in Fig.9-1 below. Photodetector:SR-3(TOPCON) Field=2 400 LCD panel TFT-LCD Module Center of the screen Fig.9-1 Optical characteristics measurement method LD-21605A12 Note 9-1 Viewing angle range is defined as follows. Normal line 12 o'clock 22 12 direction 11 21 6 o'clock direction The best viewing angle of this module is slightly leaned to 12 o'clock from normal line. Where 11max, gray scale is reversed partially. Where 11max, or in 12 direction, gray scale isn't reversed. Note 9-2 Contrast ratio is defined as follows: Luminance (brightness) with all pixels white Contrast ratio(CR)= Luminance (brightness) with all pixels black Measurement point : Center of the active area Note 9-3 Response time is obtained by measuring the transition time of photo detector output, when input signals are applied so as to make the area "black" to and from "white". White Black White t u p t u o r e t c e t e d o t o h P ) e u l a v e v i t a l e R ( Time Note 9-4 This parameter should be measured at the center of the screen and 30 minutes after turn-on. The characteristics are measured when the driver circuit is not powered. Note 9-5 The data for LED is for your reference, because LED is consumable component. LED life time : When a brightness of lamp surface become 50% of the initial value under the Standard condition. LD-21605A13 10. Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b)Our TFT-LCD module is designed to be fixed to the hardware with mounting holes on 4-corners on the backside. Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. d) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. e) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. f) Since CMOS LSI is used in this module, take care of static electricity and ensure the human earth when handling. Observe all other precautionary requirements in handling components. g) Since there is a circuit board in the module back, stress shall not be impressed in designing and assembling. If stress is impressed, there arises a possibility that circuit parts may be damaged. h) Direct sunlight on LCD panel may cause degradation of panel quality. Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is used under such environment. i) Connect GND to 4 place of mounting holes to get stable against EMI and external noise. j) When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules. k) When installing LCD modules in the cabinet, we suggest the reference torque as 0.380.3Nm (with JIS B1122 M3, 6mm). Since the optimal torque varies according to the screw or building conditions, so be sure to test it in the actual use condition. Inserting length to the module shall be within 5mm. Tapping screws shall be tighten only one time. More than two time tightening is not assured. Please take care in the case of reworking. l) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake. m) Notice: Never dismantle the module , because it will cause failure. Please don't remove the fixed tape, insulating tape etc that was pasted on the original module. (except for protection film of the panel and the crepe tape(yellow tape) temporarily adhered on the module.) n) Be careful when using it for long time with fixed pattern display as it may cause afterimage. Please use a screen saver etc., in order to avoid an afterimage. o) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. p) If a minute particle get into the module and adheres on an optical material, it may cause display irregularity issue, etc. Therefore, fine-pitch filters have to be built into cooling and inhalation hole if you intend to install a fan. q) Liquid crystal can be damaged by ultraviolet light. Be sure not to operate or storage under direct sunlight or strong ultraviolet light for a long time. r) Please storage modules in ambient temperature if possible. Below the storage temperature, liquid crystal can freeze and damage the LCD panel. Above storage temperature, it can irreversibly turn into isotropic state which cannot work as display. s) Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may induce abnormal display with polarizer film deterioration regardress of contact or noncontact to polarizer film. Be sure to confirm the component of them. LD-21605A14 12.Reliability Test Items No. Test items Test conditions High temperature Leaves the module at Ta = +70 for 240h Note 1 Leaves the module at Ta=30 for 240h Note 1 storage test Low temperature storage test High temperature and high humidity Operates the module at Tp= +40, 95%RH for 240h Note 1 (No condensation) operating test High temperature Operates the module at Tp=+70C for 240h Note 1 Operates the module at Tp=30 for 240h Note 1 operating test Low temperature operating test Strength against 200V200pF(0) 1 time for each terminals ESD 490m/s211ms, Shock test XYZ once for each direction (non-operating) Vibration test Frequency557Hz, (non-operating) Frequency58500Hz, One side0.076mm Acceleration9.8m/s2 Sweep cycle11 minutes X,Y,Z 1 hours for each directions ( total 3 hours ) Note 2 Thermal shock test Ta=30+70 , 50 cycles (0.5h) (0.5h) Result evaluation criteria Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. Note 1 Ta= Ambient temperature, Tp= Panel surface temperature Note 2 X,Y,Z directions are shown as follows: LD-21605A15 13. Packing Form 1-1 packaging detail Please refer "Figure A" for the detailed packing form. 1-2 Carton stock conditions a) Maximum number of Carton being stuck: b) Maximum number of product contained: c) Carton size: d) Total mass : Max. 9 cartons 20 Unit 534 mm(W)x349 mm(D)x195 mm(H) 7.6 kg (MAX) e) Carton stock environment: 1) 2) 3) 4) Temperature: Humidity: Ambiance: Period: 5) Unpacking: 0 ~ 40C Less than 60%RH No gases bite into electronic components and wiring materials Approximately 3month Take care not to get LCD module damaged by ESD. When unpacking, the room humidity shall be controlled to be more than 50%RH. Please unpack packages by effective means against ESD (the earthing Band, for example). 1-3 Barcode label print Serial No. consists of 10 numbers. The role of each number is as follows: 1st: last number of the year of manufacture (0-9) 2nd: month of manufacture (1-9,X,Y,Z) 3rd-4th: SHARP handling No. (fixed value=0X) 5th: manufacturing location (fixed value=D) 6th-10th: serial No. (1-9) ex. The 12th product of Dec. 2011 = 1Z0XD00012 Product number Barcode Serial number LD-21605A16 sleeve Tray 5pcs+1pcs(blank cover) Master Carton Barcode label Figure. A : packing form Modules MAX 4pcs/1tray Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328 CHINA Sharp Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE Sharp Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com JAPAN Sharp Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com SINGAPORE Sharp Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855 HONG KONG Sharp-Roxy (Hong Kong) Ltd. Level 26, Tower 1, Kowloon Commerce Centre, No. 51, Kwai Cheong Road, Kwai Chung, New Territories, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 602-603, 6/F., International Chamber of Commerce Tower, 168 Fuhua Rd. 3, CBD, Futian District, Shenzhen 518048, Guangdong, P.R. China Phone: (86) 755-88313505 Fax: (86) 755-88313515 KOREA Sharp Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or responsible in any way, for any incidental or consequential economic or property damage. LD-21605A2