Document Number: 31514 For technical questions, contact: ff2aresistors@vishay.com www.vishay.com
Revision: 25-Jul-08 4
MSM (Military M83401)
Thick Film Resistor Networks Military, MIL-PRF-83401 Qualified,
Type RZ, Single-In-Line, Molded SIP; 01, 03, 05 Schematics Vishay Dale
CIRCUIT APPLICATIONS
01 Schematic 5, 7 or 9 resistors with one pin common
“A” Profile “C” Profi le
MSM06A01 (M8340107xxxxxxC) MSM06C01 (M8340104xxxxxxC)
MSM08A01 (M8340108xxxxxxC) MSM08C01 (M8340105xxxxxxC)
MSM10A01 (M8340109xxxxxxC) MSM10C01 (M8340106xxxxxxC)
The MSM06A01, MSM08A01, MSM10A01, MSM06C01, MSM08C01 and
MSM10C01 molded single-in-line resistor networks provide the user with a
choice of 5, 7 or 9 nominally equal resistors, each connected to a common
pin (Pin No. 1).
Commonly used in the following applications:
• “Wired OR” Pull-up • Open Collector Pull-up
• Power Gate Pull-up • TTL Input Pull-down
• MOS/ROM Pull-up/Pull-down • TTL Unused Gate Pull-up
03 Schematic 3, 4 or 5 isolated resistors
“A” Profi le “C” Profile
MSM06A03 (M8340107xxxxxxG) MSM06C03 (M8340104xxxxxxG)
MSM08A03 (M8340108xxxxxxG) MSM08C03 (M8340105xxxxxxG)
MSM10A03 (M8340109xxxxxxG) MSM10C03 (M8340106xxxxxxG)
The MSM06A03, MSM08A03, MSM10A03, MSM06C03, MSM08C03 and
MSM10C03 molded single-in-line resistor networks provide the user with a
choice of 3, 4 or 5 nominally equal resistors. Each resistor is isolated from all
others.
Commonly used in the following applications:
• “Wired OR” Pull-up • Long-Line Impedance Balance
• Power Driven Pull-up • LED Current Limiting
• Power Gate Pull-up • ECL Output Pull-down
• Line Termination • TTL Input Pull-down
05 Schematic 4, 6 or 8 isolated resistors
“A” Profile “C” Profi le
MSM06A05 (M8340107xxxxxxH) MSM06C05 (M8340104xxxxxxH)
MSM08A05 (M8340108xxxxxxH) MSM08C05 (M8340105xxxxxxH)
MSM10A05 (M8340109xxxxxxH) MSM10C05 (M8340106xxxxxxH)
The MSM06A05, MSM08A05, MSM10A05, MSM06C05, MSM08C05
and MSM10C05 molded single-in-line resistor networks provide the
user with a choice of 4, 6 or 8 pair of R1/R2 resistor values for pulse
squaring and TTL dual-line terminating requirements.
PERFORMANCE
TEST CONDITIONS MAX. ΔR (Typical Test Lots)
Power Conditioning 1.5 x rated power, applied 1.5 h “ON” and 0.5 h “OFF” for 100 h ± 4 h
at + 25 °C ambient temperature ± 0.50 % ΔR
Thermal Shock 5 cycles between - 65 °C and + 125 °C ± 0.50 % ΔR
Short Time Overload 2.5 x rated working voltage for 5 s ± 0.25 % ΔR (Characteristic K)
± 0.50 % ΔR (Characteristic M)
Low Temperature Operation 45 min at full rated working voltage at - 65 °C ± 0.25 % ΔR (Characteristic K)
± 0.50 % ΔR (Characteristic M)
Moisture Resistance 240 h with humidity ranging from 80 % RH to 98 % RH ± 0.50 % ΔR
Resistance to Soldering Heat Leads immersed in + 260 °C solder to within 1/16" of body for 10 s ± 0.25 % ΔR
Shock Total of 18 shocks at 100 G's ± 0.25 % ΔR
Vibration 12 h at maximum of 20 G's between 10 and 2000 Hz ± 0.25 % ΔR
Load Life 1000 h at + 70 °C, rated power applied 1.5 h “ON”,
0.5 h “OFF” for full 1000 h period
± 0.50 % ΔR (Characteristic K)
± 2.00 % ΔR (Characteristic M)
Terminal Strength 4 1/2 pound pull for 30 s ± 0.25 % ΔR
Insulation Resistance 10 000 MΩ (minimum) -
Dielectric Withstanding No evidence of arcing or damage (200 VRMS for 1 min) -
1 2 3 n-1 n
1 2 3 4 n-1 n
1 2 3 n-1 n
R
2
R
1