PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Features Description * * * * * * * * * Pericom Semiconductor's PI49FCT3805D/E is composed of non-inverting drivers. The outputs are configured into 2 groups of one-in, five-out with independent output enable. Group B has an extra MON output. Excellent output signals to power and ground ratio minimize power and ground noise and also improves output performance. Low output skew: <200ps Switching frequency up to 166 MHz Fast output rise/fall time: <1.0ns Low propagation delay: <2.5ns Low input capacitance: <6.0pF Balanced CMOS outputs Industrial Temperature: -40C to +85C 3.3V 10% operation, 5V Input Tolerant Packaging (Pb-free & Green available): - 20-pin 300-mil wide SOIC (S) - 20-pin 150-mil wide QSOP (Q) - 20-pin 209-mil wide SSOP (H) - 20-pin 173-mil wide TSSOP (L) Block Diagram Pin Configuration VCC 1 20 VCCB OA0 2 19 OB0 OA1 3 18 OB1 OA2 4 17 OB2 GNDA 5 16 GNDB OA3 6 15 OB3 OA4 7 14 OB4 GNDQ 8 13 MON OEA 9 12 OEB INA 10 11 INB OEA 5 INA OA04 5 INB OB04 OEB MON Truth Table(1) Pin Description Pin Name Inputs Deescription OEX Hi-Z State Output Enable Inputs (Active Low) INX Outputs OEX INX OAX MON Clock Inputs L L L L OAN, OBN Clock Outputs L H H H MON Monitor Output H L Z L GND Ground H H Z H VCC Power Note: 1. H = High Voltage Level, L = Low Voltage Level, Z = High Impedance 08-0298 1 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................................................. -65C to +150C Ambient Temperature with Power Applied ................................ -40C to +85C Input Voltage to GND Potential (Inputs & VCC Only) .................. -0.5V to 5.5V Output Voltage to GND Potential (Outputs & I/O Only)...-0.5V to +VCC +0.5V VCC Input Voltage ........................................................................ -0.5V to +4.6V Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics (TA = -40C to +85C, VCC = 3.3V 0.3V) Symbol Test Conditions(1) Parameters Min. Typ. VCC-0.2 2.4(3) 2.4(3) 3.0 3.0 Max. Units 0.2 0.4 0.4 V VOH Output High Voltage VCC = Min., VIN = VIL or VIH IOH = -0.1mA IOH = -8mA IOH = -12mA VOL Output Low Voltage VCC = Min., VIN = VIL or VIH IOH = 0.1mA IOH = 8mA IOH = 12mA VIH Input High Voltage Low Logic 2.0 5.5 VIL Input Low Voltage High Logic -0.5 0.8 IIH Input High Current VCC = Max., VIN = 5.5V 1 IIL Input Low Current VCC = Max., VIN = GND -1 IOZH IOZL High Impedance output current VCC = Max., all outputs disabled 1 -1 VIK Clamp Diode Voltage VCC = Min., IIN = -18mA IODH IODL IOS 0.2 0.3 VOUT = VCC VOUT = GND -0.7 -1.2 -40 -74 -100 VOUT = 1.5V, VIN = VIL or VIH, VCC = 3.3V 50 90 130 VCC = Max., VOUT = GND -60 -100 -120 Output High Current(4, 5) VOUT = 1.5V, VIN = VIL or VIH, VCC = 3.3V Output Low Current(4, 5) Short Circuit Current(4, 5) A V mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, +25C ambient and maximum loading. 3. VOH = VCC - 0.6V at rated current. 4. This parameter is determined by device characterization but is not production tested. 5. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 08-0298 2 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Capacitance (TA = 25C, f = 1 MHz) Parameters(1) Description Test Conditions Typ Max. CIN Input Capacitance VIN = 0V 3.0 4 COUT Output Capacitance VOUT = 0V -- 6 Units pF Note: 1. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Test Conditions(1) Description ICC Quiescent Power Supply Current VCC = Max. IDD Dynamic Supply Current per Output VCC = 3.6V, CL = 15pF, All Outputs Toggling IC ICC Total Power Supply Current Supply Current per inputs @ TTL High VIN = GND or VDD Min. Typ. (2) Max. 0.1 30 Units A VCC = 3.6V, CL = 15pF, All Outputs Toggling, fi = 133 MHz VCC = 3.6V, CL = 15pF, All Outputs Toggling, fi = 166 MHz VCC = Max. 80 120 VIN = VCC or GND 100 135 VIN = VCC -0.6V or GND 100 135 VIN = VCC or GND 120 160 VIN = VCC -0.6V or GND 120 160 VIN = VCC -0.6V(3) 45 300 mA/ MHz A Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25C ambient. 3. Per TTL driven input (VIN = VCC - 0.6V); all other inputs at VCC or GND. 08-0298 3 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Switching Characteristics over Operating Range Parameters tPLH tPHL Test Conditions(1) Description Propagation Delay INN to ON tR/tF CLKn Rist/Fall Time 0.8V ~ 2.0V CL = 15pF, 133 MHz (3805D) 166 MHz (3805E) 3805D 3805E Max. Max. 3.0 2.5 1.5 1.0 270 270 270 200 Units ns (3) Pulse Skew (3) Output Skew tSK(t) (3) Package Skew 550 550 tZL, tZH, tLZ, tHZ Enable/Disable Time 5.2 5.0 ns FMAX Input Frequency 133 166 MHz tSK(o) tSK(p) ps Note: 1. These parameters are guaranteed by design 2. Series Resistor loading = 33 (See Test Circuit) Switch Position Test Switch Disable LOW Enable LOW 6V Disable HIGH Enable HIGH GND All Other Inputs Open Definitions: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. Enable/Disable Time Test Set-Up Tests Circuit 6V VCC S VCC 33 Pulse Generator f = 125MHz 500 D.U.T. 50 33 Pulse Generator CL 15pF D.U.T. 50 08-0298 4 CL 15pF PS8492D 500 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Switching Waveforms Output Skew - tSK(o) Propagation Delay 3V Input 3V Input 1.5V 0V 1.5V tPLHx tPHLx 0V VOH tPHL tPLH Ox VOH Output 1.5V VOL 1.5V tSK(o) tSK(o) VOL VOH Oy Enable and Disable Times 1.5V VOL tPHLy tPLHy Enable Disable 3V OE tSK(o) = | tPLHy tPLHx | or | tPHLy tPHLx | 1.5V 0V tPZL 3.0V 3.0V Output Normally Low Switch Closed Enable Disable 3V 1.5V 0.3V tPZH Output Normally High Pulse Skew - tSK(p) tPLZ OE VOL 1.5V tPHZ 0.3V Switch Open 0V VOH 1.5V 0V tPLZ tPZL Output Normally Low 0V 1.5V 0.3V tPZH Package Skew - tSK(t) Output Normally High 3V Input 1.5V 3.0V 3.0V Switch Closed Switch Open VOL tPHZ 0.3V VOH 1.5V 0V 0V 0V tPHL1 tPLH1 VOH Package 1 Output 1.5V VOL tSK(t) tSK(t) VOH Package 2 Output 1.5V tPLH2 VOL tPHL2 tSK(t) = | tPLH2 tPLH1 | or | tPHL2 tPHL1 | 08-0298 5 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Packaging Mechanical: 20-Pin 300-mil wide SOIC (S) $/#5-%.4 #/.42/, ./ 0$ 2%6)3)/. $ $!4% X 2%& 888 $%./4%3 #/.42/,,).' 888 $)-%.3)/.3 ). -),,)-%4%23 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com .OTES #ONTROLLING DIMENSIONS IN MILLIMETERS 2EF *%$%# -3 $!# 08-0298 3%!4).' 0,!.% "3# $%3#2)04)/. 0IN -IL 7IDE 3/)# 0!#+!'% #/$% 3 6 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Packaging Mechanical: 20-Pin 150-mil wide QSOP (Q) DOCUMENT CONTROL NO. PD - 1202 20 REVISION: H .008 0.20 MIN. .150 .157 DATE: 10/22/07 .008 .013 0.20 0.33 3.81 3.99 Guage Plane .010 0.254 1 Detail A .337 8.56 .344 8.74 .058 REF 1.47 .041 1.04 REF .015 x 45 0.38 .053 1.35 .069 1.75 Detail A .007 .010 SEATING PLANE .025 BSC 0.635 0-6 .016 .035 0.41 0.89 .004 0.101 .010 0.254 0.178 0.254 .228 .244 5.79 6.19 .008 0.203 .012 0.305 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com Note: 1) Controlling dimensions in inches. 2) Ref: JEDEC MO-137B/AD 3) Dimensions do not include mold flash, protrusions or gate burrs DESCRIPTION: 20-Pin, 150-Mil Wide, QSOP PACKAGE CODE: Q 08-0298 7 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Packaging Mechanical: 20-Pin 209-mil wide SSOP (H) DATE: 04/10/08 DESCRIPTION: 20-Pin, 209-Mil Wide, SSOP PACKAGE CODE: H20 DOCUMENT CONTROL #: PD-1240 REVISION: E 08-0140 08-0298 8 PS8492D 11/13/08 PI49FCT3805D/E 3.3V, 2 x 1:5 CMOS Clock Driver Packaging Mechanical: 20-Pin 173-mil wide TSSOP (L) DOCUMENT CONTROL NO. PD - 1311 20 REVISION: E DATE: 03/09/05 .169 .177 4.3 4.5 1 .252 .260 6.4 6.6 .004 0.09 .008 0.20 .047 1.20 Max .007 .012 0.19 0.30 .0256 BSC 0.65 0.45 0.75 SEATING PLANE .018 .030 .238 .269 6.1 6.7 .002 0.05 .006 0.15 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com Note: 1. Package Outline Exclusive of Mold Flash and Metal Burr 2. Controlling dimentions in millimeters 3. Ref: JEDEC MO-153F/AC DESCRIPTION: 20-Pin, 173-Mil Wide, TSSOP PACKAGE CODE: L Ordering Information Ordering Code Package Code Package Description PI49FCT3805DHE H Pb-free & Green, 20-pin 209-mil SSOP PI49FCT3805DQ Q 20-pin 150-mil QSOP PI49FCT3805DQE Q Pb-free & Green, 20-pin 150-mil QSOP PI49FCT3805DSE S Pb-free & Green, 20-pin 300-mil SOIC PI49FCT3805EH H 20-pin 209-mil SSOP PI49FCT3805EH H 20-pin 209-mil SSOP PI49FCT3805EQ Q 20-pin 150-mil QSOP PI49FCT3805EQ Q 20-pin 150-mil QSOP PI49FCT3805EL L 20-pin 173-mil TSSOP PI49FCT3805EL L 20-pin 173-mil TSSOP Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. Number of Transistors = TBD Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 08-0298 9 PS8492D 11/13/08