PE4140-52 - Peregrine Semiconductor Corp.

Page 1 of 10

Document No. 70-0089-09 │www. psemi.com

The PE4140 is an ultra-high linearity passive broadband Quad

MOSFET array with high dynamic range performance capable

of oper ati o n beyon d 6.0 GHz. This qu ad arr ay o pe r ates wit h

differential signals at all ports (RF, LO, IF), allowing mixers to

be built that use LO powers from -7 dBm to +20 dBm. Typical

applications range from frequency up/down-conversion to

phase detec tion for Cellular/PCS Bas e Stations, Wireless

Broadband Communications and STB/Cable modems.

The PE4140 is manufactured on Peregrine’s UltraCMOS™

pro c ess, a patented variation of silicon -on-insulator (SOI )

technology on a sapphire substrate, offering the performance

of GaAs with the econom y and integr ation of conventi on al

CMOS.

Pro duct Specification

Ultra-High Linearity UltraCMOS™

Broadband Quad MOSFET Array

Product Description

Figure 1. Functional Diagram

PE4140

Features

Ultimate Quad MOSFET array

Ultra-high linearity, broadband

performance bey on d 6.0 GH z

Id ea l for mixer application s

Up/down conversion

Low conversion loss

Hi gh LO Isol a t ion

Packaged in small 6-lead 3x3 mm DFN

Fig ure 2. Package Type

6-lead DFN

RF

LO IF

Symbol Characteristics Test Conditions Min Typ Max Units

FTYP Operating Frequency Range1 DC 6.0 GHz

VDS Drain-Source Voltage VGS = +3V, IDS = 4 0 mA 260 320 380 mV

VDS Match Drain-Source Voltage Match 12 40 mV

VT Threshold Voltage VDS = 0.1V; per AS T M F617- 00 -100 mV

R DS Drain-Source ‘ON’ Resistance VGS = +3V, IDS = 40 mA 6.5 7.75 9.5 Ω

Table 1. AC and DC Electrical Specifications @ +25 °C

Note 1: Typical untested operating frequency range of Quad MOSFET transistors.

Product Specification

PE4140

Page 2 of 10

Table 2 . Pin Descriptions

Table 3. Absolute Maximum Ratings

Electrostatic Discharge (ESD) Precautions

This MOSFET device has minimally protected

inputs and is highly susceptible to ESD dama ge.

Whe n hand ling this UltraCMOS ™ device,

obs er ve th e same preca uti o ns th at y ou wo uld us e

with other ESD-sensitive devices.

Latc h-Up Avoidance

Unlike conven tional CMOS devices, UltraCMOS™

devices are immune to latch-up.

Figure 3. Pin Configuration (Top View)

Exceeding absolute maximum ratings may cause

permanent damage. Operation should be

restricted to the limits in the Operating Ranges

tabl e. Oper ation betw e en op er a ti ng ran ge

maxi mum and absolute maximu m fo r extended

periods may reduce reliability.

Exposed

Solder Pad

(bottom s ide)

IF1

RF1

RF2

IF2

LO1

LO24

5

6

3

2

1

No. Pin

Name Description

1 IF1 IF Output Connection (Drain)

2 RF1 RF Input Connection (Source)

3 RF2 RF Input Connection (Source)

4 LO2 LO Input Connection (Gate)

5 LO1 LO Input Connection (Gate)

6 IF2 IF Output Connection (Drain)

Symbol Parameters/

Conditions Min Max Units

TST Storage temperature

range -65 150 °C

TOP Operating temperature

range -40 85 °C

VDC + AC Maximum DC plus peak

AC voltage across Drain-

Source ±3.3 V

VDC+AC Maximum DC plus peak

AC voltage across Gate-

Drain or Gate-Source ±4.2 V

VESD HBM1 ESD Voltage 100 V

Device Description

The PE 41 40 passiv e broadba nd Qu ad MOSFET

arr ay is desi g n ed for us e i n up- co nvers ion and

down-conversion applications for high

performance systems such as cellular

infrastructure equipment and STB/CATV systems.

The PE4140 is an ideal mixer core for a wide

range of mixer products, including module level

solutions that incorporate baluns or other single-

ended matching structures enabling three-port

operation.

The per f or m an c e lev el of thi s pas s i ve mix er is

made possible by the very high linearity afford ed

by Peregrine’s UltraCMOS™ process.

Marking

Packaged devices are marked with part number

“4140”, date code and lot code.

Moist u re Sen sit i vit y L evel

The Moisture Sensitivity Level rating for the

PE4140 in the 6-lead 3x3 DFN package is MSL1.

Note 1: ML_STD 883 Method 3015.7

Product Specification

PE4140

Page 3 of 10

Evaluation Kit

Figure 4. Evaluation Board Layout

Figure 5. Evaluation Board Schematic

Peregr ine S pec ification 101/ 0090

Peregr ine S pec ification 102/ 0115

Applications Support

If you have a problem with your evaluation kit or if you have

applications questions, please contact applications support:

E-Mail: help@psemi.com (fastest response)

Phone: (858) 731-9400

Note: This is the complete evaluation board schematic; which can be used for multiple configurations. Not all

components need be populated . Refer to 'typical schematics' on following pages.

Product Specification

PE4140

Page 4 of 10

PE4140

16

5

43

2

1

2

3

4

45

5

R16

3 pF

R2

1.2 nH

R12

1.2 nH

R3

2.7 nH

R8

2.7 nH

T2

M/A Com

ETC1.6-4-2-3

T1

M/A Com

ETC1.6-4-2-3

T3

TOKO

617DB-1024

J3

LO Input

J4

RF Input

J6

IF Out

Figure 6. Typical Schematic for a PCS Application

Table 4. Typical Performance in a PCS Application @ +25 °C

Parameter Minimum Typical Maximum Units

Frequency Range**

LO

RF

IF

1630

1700

--

70

2130

2200

MHz

Conversion Loss**

(Includes balun l osses) 8.5 dB

Isolation**

LO-RF

LO-IF

36

26

dB

Input IP3** 32 dBm

Input 1 dB Compression** 22 dBm

** Data taken on an Evalu ation Board narrow -band tuned t o cover the PCS band, IF = 73MHz low-side, LO drive = 17dBm.

Product Specification

PE4140

Page 5 of 10

-40

-35

-30

-25

-20

-15

-10

-5

0

1700 1750 1800 1850 1900 1950 2000 2050 2100

Isolation (dB)

Frequency (MHz)

LO-IF

LO-RF

5

6

7

8

9

10

1700 1750 1800 1850 1900 1950 2000 2050 2100

Conversion Loss (dB) @ 17dBm Lo

IF=73Mhz Low-side

Frequency (MHz)

Conversion Loss

0

5

10

15

20

25

30

35

40

1700 1750 1800 1850 1900 1950 2000 2050 2100

IIP3 (dBm) @ 17dBm Lo

Frequency (MHz)

Typical P erformance Plots in a PCS Application @ +25 °C (LO=17 dBm, IF=73 MHz Low-side)

Figure 8. Conversion Loss vs. Frequency

Figure 9. LO-RF & LO-IF Isolation

Fig ure 7. IIP3 vs. Frequenc y

Product Specification

PE4140

Page 6 of 10

Figure 10. Typical Sche matic for a CATV Application

(Reference Designators Refer to locations on Evaluation Board: 101/0090)

U1

MLP6-3X3 2

1

3 4

5

6

L2

4.7nH

J3

LO Input

1 T1

ETC1.6-4-2-3

1

4

5

3

2

L1

4.7nH

T

2

ETC1.6-4-2-3

1

4

5

3

2

R16

3.0pF

(Cut short between pads)

J4

RF Input

1

T3

ETC1-1-13

1

4 5

3 2

J6

IF Out

1

Note: L1 and L2 provide LO port m atching for optimum performance. Typical gat e capacitance is approxim ately 2.5 pF.

Table 5. Typical Performance in a CATV Application @ +25 °C

Parameter Minimum Typical Maximum Units

Frequency Range**

LO

RF

IF

1116

54

--

1062

1926

864

MHz

Conversion Loss**

(Includes balun l osses) 6.5 dB

Isolation**

LO-RF

LO-IF

40

28

dB

Input IP3** 23 dBm

Input 1 dB Compression** 13 dBm

** Data taken on an Evaluation Board tuned for a broadband CATV application, IF = 1062 MHz, RF drive = -5 dBm, LO drive = 10 dBm.

Product Specification

PE4140

Page 7 of 10

-60

-50

-40

-30

-20

-10

0

1000 1200 1400 1600 1800 2000

Isolation (dB)

Frequency (MHz)

LO-RF

LO-IF

0

2

4

6

8

10

0 200 400 600 800 1000

Conversion Loss (dB) @10dBm LO

Frequency (MHz)

0

5

10

15

20

25

30

0 200 400 600 800 1000

IIP3 (dBm) @10dBm LO

Frequency (MHz)

Typical Performance Plots in a CATV Application @ +25 °C

Figure 12. Conversion Loss vs. Frequency

Figure 13. LO-RF & LO-IF Isolation

Figure 11. IIP3 vs. Frequency

Product Specification

PE4140

Page 8 of 10

6-lead DFN

Figure 14. Package Drawing

NOTE: Th e exposed solder pad (on the bottom of the package) is not electrically connected to any other pin

(isolated).

Figure 15. Marking Specifications

4140

YYWW

ZZZZZ

YYWW = Date Code (last two digits of year and work week)

ZZZZZ = Last five digits of Lot Number

06L SLP

(3x3mm)

Product Specification

PE4140

Page 9 of 10

6-lead DFN

Table 7. Ordering Information

Or der Code Part Marking Description Package Shipping Method

4140-51 4140 PE4140G-06DFN 3x3mm-Cut tape or loose Green 6-lead 3x3 mm DFN Cut tape or loose

4140-52 4140 PE4140G-06DFN 3x3mm-3000C Green 6-lead 3x3 mm DFN 3000 units / T&R

4140-00 PE4140-EK PE4140-06DFN 3x3mm-EK Evaluation Kit 1 / Box

Dimension DFN 3x3 mm

Ao 3.23 ± 0.1

Bo 3.17 ± 0.1

Ko 1.37 ± 0.1

P 4 ± 0.1

W 8 +0.3, -0.1

T 0.254 ± 0.02

R7 Quantity 3000

R13 Quantity N.A.

Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel

Table 6. Dimensions

Figure 16. Tape and Reel Specifications

Device Orientation in Tape

Top of

Device

Pin 1

Tape Feed Dire c t ion

Product Specification

PE4140

Page 10 of 10

Sales Offices

The Americas

Peregrine Semiconductor Corporation

9380 Carroll Park Drive

San Diego, CA 92121

Tel: 858-731-9400

Fax: 858- 731-9499

Europe

Peregrine Semiconductor Europe

Bâtiment Maine

13-15 rue des Quatre Vent s

F-92380 Garches , France

Tel: +33-1-4741-9173

Fax : +3 3-1 -4741 -917 3

For a list of represent atives in your area, please refer to our Web site at: w ww.psemi.com

Data Sheet Identification

Advance Information

The product is in a formative or design st age. The data

sheet contains design target specificat ions f or product

development. Specifications and features may change in

any manner without notice.

Preliminary Specification

The data sheet contains pr eliminary data. Additional data

may be added at a later date. Peregrine reserves the right

to change specifications at any time without notice in order

to supply t he best possible product.

Product Specification

The data sheet contains final data . In the event Peregrine

dec ide s to cha nge the spe c ific a tions, Peregr in e will notify

customers of t he intended changes by issuing a CNF

(Customer Notification Form).

The information in t his data sheet is believed to be reliable.

Howeve r, Pere grin e assume s no liabilit y for th e use of this

information. Use shall be entir ely at the user’s own risk.

No patent rights or licenses t o any circuits described in this

data sheet ar e implied or granted to any third party.

Peregrine’s pr oducts are not designed or int ended for use in

devices or systems intended f or surgical implant, or in other

applications intended t o support or sustain life, or in any

application in which the failure of the Peregrine pr oduct could

create a situat ion in which personal injury or death m ight occur.

Peregr ine assumes no liability for damages, including

consequential or incidental dam ages, arising out of the use of

its products in such applications.

The Peregrine name, logo, and UTSi are r egistered tr ademarks

and UltraCMOS, HaRP, MultiSwitch and DuNE ar e trademarks

of Peregrine Semiconductor Corp.

High-Reliability and Defense Products

Americas

San Diego, CA, USA

Phone: 858- 731-9475

Fax: 848- 731-9499

Europe/Asia-Pacific

Aix-En-Provence Cedex 3, France

Phone: +33- 4- 4239-3361

Fax: +33- 4-4239- 7227

Peregri ne Semiconduc tor, Asia Pacific (AP AC)

Shanghai, 200040, P.R. China

Tel: +86-21-5836-8276

Fax: +86- 21-5836-7652

Peregrine Semiconductor, Korea

#B-2607, Kolon Tr ipolis, 210

Geumgok-dong, Bundang-gu, Seongnam-si

Gyeonggi-do, 463-943 South Korea

Tel: +82-31-728-3939

Fax: +82- 31-728-3940

Peregrine Semiconductor K.K., Japan

Teiko k u Hote l Tower 10B-6

1- 1-1 Uchisaiwai-c ho, Chiy o da- k u

Tokyo 100-0011 Japan

Tel: +81-3-3502-5211

Fax: +81- 3-3502- 5213