Product Specification PE4140 Ultra-High Linearity UltraCMOSTM Broadband Quad MOSFET Array Product Description Features The PE4140 is an ultra-high linearity passive broadband Quad MOSFET array with high dynamic range performance capable of operation beyond 6.0 GHz. This quad array operates with differential signals at all ports (RF, LO, IF), allowing mixers to be built that use LO powers from -7 dBm to +20 dBm. Typical applications range from frequency up/down-conversion to phase detection for Cellular/PCS Base Stations, Wireless Broadband Communications and STB/Cable modems. Ultimate Quad MOSFET array Ultra-high linearity, broadband performance beyond 6.0 GHz Ideal for mixer applications Up/down conversion Low conversion loss The PE4140 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. High LO Isolation Packaged in small 6-lead 3x3 mm DFN Figure 1. Functional Diagram Figure 2. Package Type 6-lead DFN LO IF RF Table 1. AC and DC Electrical Specifications @ +25 C Symbol Characteristics Test Conditions FTYP Operating Frequency Range1 VDS Drain-Source Voltage VDS Match Drain-Source Voltage Match VT Threshold Voltage VDS = 0.1V; per ASTM F617-00 R DS Drain-Source `ON' Resistance VGS = +3V, IDS = 40 mA Min Typ Max Units 6.0 GHz 320 380 mV 12 40 mV DC VGS = +3V, IDS = 40 mA 260 -100 6.5 7.75 mV 9.5 Note 1: Typical untested operating frequency range of Quad MOSFET transistors. Document No. 70-0089-09 www.psemi.com (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 10 PE4140 Product Specification Electrostatic Discharge (ESD) Precautions Figure 3. Pin Configuration (Top View) IF1 1 RF1 2 RF2 3 Exposed Solder Pad (bottom side) This MOSFET device has minimally protected inputs and is highly susceptible to ESD damage. When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. 6 IF2 5 LO1 4 LO2 Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Device Description The PE4140 passive broadband Quad MOSFET array is designed for use in up-conversion and down-conversion applications for high performance systems such as cellular infrastructure equipment and STB/CATV systems. Table 2. Pin Descriptions Pin No. Pin Name 1 IF1 IF Output Connection (Drain) 2 RF1 RF Input Connection (Source) 3 RF2 RF Input Connection (Source) 4 LO2 LO Input Connection (Gate) 5 LO1 LO Input Connection (Gate) 6 IF2 IF Output Connection (Drain) Description The PE4140 is an ideal mixer core for a wide range of mixer products, including module level solutions that incorporate baluns or other singleended matching structures enabling three-port operation. The performance level of this passive mixer is made possible by the very high linearity afforded by Peregrine's UltraCMOSTM process. Table 3. Absolute Maximum Ratings Parameters/ Conditions Min Max Units TST Storage temperature range -65 150 C TOP Operating temperature range -40 85 C VDC + AC Maximum DC plus peak AC voltage across DrainSource 3.3 V VDC+AC Maximum DC plus peak AC voltage across GateDrain or Gate-Source 4.2 V HBM1 ESD Voltage 100 V Symbol VESD Marking Packaged devices are marked with part number "4140", date code and lot code. Moisture Sensitivity Level The Moisture Sensitivity Level rating for the PE4140 in the 6-lead 3x3 DFN package is MSL1. Note 1: ML_STD 883 Method 3015.7 Exceeding absolute maximum ratings may cause permanent damage. Operation should be restricted to the limits in the Operating Ranges table. Operation between operating range maximum and absolute maximum for extended periods may reduce reliability. (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 10 Document No. 70-0089-09 UltraCMOSTM RFIC Solutions PE4140 Product Specification Evaluation Kit Figure 4. Evaluation Board Layout Peregrine Specification 101/0090 Applications Support If you have a problem with your evaluation kit or if you have applications questions, please contact applications support: E-Mail: help@psemi.com (fastest response) Phone: (858) 731-9400 Figure 5. Evaluation Board Schematic Peregrine Specification 102/0115 Note: This is the complete evaluation board schematic; which can be used for multiple configurations. Not all components need be populated. Refer to 'typical schematics' on following pages. Document No. 70-0089-09 www.psemi.com (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 10 PE4140 Product Specification Figure 6. Typical Schematic for a PCS Application J3 LO Input T1 M/A Com ETC1.6-4-2-3 4 3 R2 1.2 nH 2 5 1 R12 1.2 nH T2 M/A Com ETC1.6-4-2-3 5 1 R3 2.7 nH 4 3 5 PE4140 6 2 2 1 3 R16 3 pF J4 RF Input 4 R8 2.7 nH 2 3 4 1 5 T3 TOKO 617DB-1024 J6 IF Out Table 4. Typical Performance in a PCS Application @ +25 C Parameter Minimum Typical Maximum Units LO 1630 -- 2130 MHz RF 1700 -- 2200 MHz Frequency Range** IF 70 MHz 8.5 dB LO-RF 36 dB LO-IF 26 dB Input IP3** 32 dBm Input 1 dB Compression** 22 dBm Conversion Loss** (Includes balun losses) Isolation** ** Data taken on an Evaluation Board narrow-band tuned to cover the PCS band, IF = 73MHz low-side, LO drive = 17dBm. (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 10 Document No. 70-0089-09 UltraCMOSTM RFIC Solutions PE4140 Product Specification Typical Performance Plots in a PCS Application @ +25 C (LO=17 dBm, IF=73 MHz Low-side) Figure 8. Conversion Loss vs. Frequency Figure 7. IIP3 vs. Frequency 40 10 Conversion Loss (dB) @ 17dBm Lo IF=73Mhz Low-side 35 IIP3 (dBm) @ 17dBm Lo 30 25 20 15 10 9 8 Conversion Loss 7 6 5 0 1700 1750 1800 1850 1900 1950 2000 2050 2100 Frequency (MHz) 5 1700 1750 1800 1850 1900 1950 2000 2050 2100 Frequency (MHz) Figure 9. LO-RF & LO-IF Isolation 0 -5 Isolation (dB) -10 -15 -20 LO-IF -25 LO-RF -30 -35 -40 1700 1750 1800 1850 1900 1950 2000 2050 2100 Frequency (MHz) Document No. 70-0089-09 www.psemi.com (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 10 PE4140 Product Specification Figure 10. Typical Schematic for a CATV Application (Reference Designators Refer to locations on Evaluation Board: 101/0090) J3 LO Input 1 4.7nH L1 ETC1.6-4-2-3 4 T1 3 U1 4 5 6 2 5 ETC1.6-4-2-3 T 2 1 5 1 3 2 1 3 2 J4 1 2 RF Input MLP6-3X3 L2 4.7nH R16 3.0pF 3 4 1 (Cut short between pads) 5 4 T3 ETC1-1-13 1 J6 IF Out Note: L1 and L2 provide LO port matching for optimum performance. Typical gate capacitance is approximately 2.5 pF. Table 5. Typical Performance in a CATV Application @ +25 C Parameter Minimum Typical Maximum Units LO 1116 -- 1926 MHz RF 54 -- 864 MHz Frequency Range** IF Conversion Loss** (Includes balun losses) Isolation** LO-RF 1062 MHz 6.5 dB 40 dB LO-IF 28 dB Input IP3** 23 dBm Input 1 dB Compression** 13 dBm ** Data taken on an Evaluation Board tuned for a broadband CATV application, IF = 1062 MHz, RF drive = -5 dBm, LO drive = 10 dBm. (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 10 Document No. 70-0089-09 UltraCMOSTM RFIC Solutions PE4140 Product Specification Typical Performance Plots in a CATV Application @ +25 C Figure 11. IIP3 vs. Frequency Figure 12. Conversion Loss vs. Frequency 30 10 Conversion Loss (dB) @10dBm LO IIP3 (dBm) @10dBm LO 25 20 15 10 5 0 8 6 4 2 0 0 200 400 600 800 1000 0 200 400 600 800 1000 Frequency (MHz) Frequency (MHz) Figure 13. LO-RF & LO-IF Isolation 0 -10 Isolation (dB) -20 LO-IF -30 -40 -50 -60 1000 LO-RF 1200 1400 1600 1800 2000 Frequency (MHz) Document No. 70-0089-09 www.psemi.com (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 10 PE4140 Product Specification Figure 14. Package Drawing 06L SLP (3x3mm) 6-lead DFN NOTE: The exposed solder pad (on the bottom of the package) is not electrically connected to any other pin (isolated). Figure 15. Marking Specifications 4140 YYWW ZZZZZ YYWW = Date Code (last two digits of year and work week) ZZZZZ = Last five digits of Lot Number (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 8 of 10 Document No. 70-0089-09 UltraCMOSTM RFIC Solutions PE4140 Product Specification Figure 16. Tape and Reel Specifications 6-lead DFN Tape Feed Direction Pin 1 Top of Device Table 6. Dimensions Dimension DFN 3x3 mm Ao 3.23 0.1 Bo 3.17 0.1 Ko 1.37 0.1 P 4 0.1 W 8 +0.3, -0.1 T 0.254 0.02 R7 Quantity 3000 R13 Quantity N.A. Device Orientation in Tape Note: R7 = 7 inch Lock Reel, R13 = 13 inch Lock Reel Table 7. Ordering Information Order Code Part Marking Description Package Shipping Method 4140-51 4140 PE4140G-06DFN 3x3mm-Cut tape or loose Green 6-lead 3x3 mm DFN Cut tape or loose 4140-52 4140 PE4140G-06DFN 3x3mm-3000C Green 6-lead 3x3 mm DFN 3000 units / T&R 4140-00 PE4140-EK PE4140-06DFN 3x3mm-EK Evaluation Kit 1 / Box Document No. 70-0089-09 www.psemi.com (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 9 of 10 PE4140 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation Peregrine Semiconductor, Asia Pacific (APAC) 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 High-Reliability and Defense Products Peregrine Semiconductor, Korea #B-2607, Kolon Tripolis, 210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-943 South Korea Tel: +82-31-728-3939 Fax: +82-31-728-3940 Peregrine Semiconductor K.K., Japan Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Americas San Diego, CA, USA Phone: 858-731-9475 Fax: 848-731-9499 Europe/Asia-Pacific Aix-En-Provence Cedex 3, France Phone: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a CNF (Customer Notification Form). (c)2005-2009 Peregrine Semiconductor Corp. All rights reserved. Page 10 of 10 The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS, HaRP, MultiSwitch and DuNE are trademarks of Peregrine Semiconductor Corp. Document No. 70-0089-09 UltraCMOSTM RFIC Solutions