MS & 97B - Series ACR11 0601 MS And 97B Series Introduction Amphenol MS and 97B series are two series of thread & Bayonetcoupled connectors designed to meet the operating requirements of MIL-C-5015. Available in a variety of styles and classes, these connectors are primarily used in a range of military and industrial applications where specific degrees of environmental protection are required. Although MS series have identical insert arrangements and other similar component parts, the two series differ in that Amphenol MS series of connectors are also qualified to meet the operating requirements of Defence Standard Joint Services Specification JSS50812 , issued by the Electronics Components Standardization Organisation (LCSO). Amphenol 97B connectors feature a quick mating bayonet coupling with an audible full mating feature. This series uses the same MIL-C-5015 insert patterns and are used in high shock and vibration environments encountered in commercial, geophysical, aerospace, ground support and shipboard applications. Page Contents Introduction Connector styles General description Electrical data Insert orientations Insert arrangements Shell types Back accessories Other accessories MS/97B Series Ordering MS/97B series connectors 1 1 2-3 4 5 6 7-18 19-25 26-29 30-33 34 35 AMPHENOL MS And 97B Series Connector Styles - MS Class F MS-3108 MS-4108 Class A=R MS-3106 MS-4106 Class A MS-3100 MS-4100 Class E and F MS-3101 MS-4101 Class R cable clamp AMPHENOL back shell grommet sleeve 2 grommet MS-3102 MS-4102 MS And 97B Series Connector Styles - 97B Class F 97B - 3108 97B - 4108 Class A=R 97B - 3106 97B - 4106 Class A 97B - 3100 97B - 4100 Class F 97B - 3101 97B - 4101 97B - 3103 97B - 4103 Class R cable clamp back shell grommet sleeve grommet 97B - 3102 97B - 4102 3 AMPHENOL MS And 97B Series General Description These electrical connectors are designated MS because the interchangeability and operating characteristics are determined by U.S. Military Specifications. These specifications are revised from time to time to incorporate performance requirements dictated by design advances and more stringent requirements of allied equipment. The several designations of MS and 97B connectors meet different requirements of MILC-5015. These designations and general descriptions are as follows : Inserts and grommet Synthetic inserts and grommet manufactured according to MIL-R-3065, offer high dielectric strength and are resistant to oils, gasoline and low temperature. DAP is dimensionally stable, has high arc resistance and high insulation resistance under both humidity and thermal stress. General description Plugs are available in A, F and R types. Receptacles are available in A, E, F and R types. Shell A Solid back shell Shell constructions include solid back shell (A) and environmental resistant (E, F & R). Environmental resistant connectors provide a moisture barrier and assure a positive seal. Shell styles consist of wall type receptacles (3100), cable receptacles (3101), box receptacles (3102), straight plugs (3106) and angle plugs (3108). Shell hardware is manufactured from aluminium alloy and cadmium plated with olive drab chromate finish. This finish has excellent conductivity; it is non-reflecting and corrosion resistant. Black anodised finish and cadmiumfree zinc plating with olive drab chromate finish are also available. For details, contact factory. Intended for general service usage to provide convenient means of connecting and disconnecting electrical circuits in industrial and military applications. Environmental resisting Intended for use where the connector will be subject to heavy condensation and rapid changes in temperature or pressure and/or where the connector is subjected to high vibratory conditions. E Environmental resisting with grommet seal and strain relief backshell except for 3102 type. Contacts F Environmental resisting with grommet seal, strain relief backshell and front gasket seal for plug type. Pin and socket contacts are of brass and generally silver plated. Gold plating is also available. For details contact factory. These contacts are available for solder or crimp termination. Special arrangements of contacts for pre-mating and pre-earth are also available. R Environmental resisting with grommet seal, shorter and lightweight. Features for 97B reverse bayonet coupling connectors with Mil-C-5015 insert patterns: Available in both crimp and solder terminations Contacts available in gold and silver plating Numerous finishes available Zinc alloy plating (cadmium free) available Quick positive coupling Audible and tactile indication of full coupling Waterproof No lockwiring required High shock and vibration capabilities Rugged construction; aluminum or stainless steel components Intermateable with existing VG95234 connectors 500 couplings minimum Insert available in Neoprene material (alternate inserts materials available upon request) Operating temperature range with Neoprene inserts: -550C to +1250C AMPHENOL 4 MS And 97B Series Electrical Data Dielectric strength Service rating Test Voltage Vac rms Inst. 1000V A 2000V D 2800V E 3500V B 4500V C 7000V Contact rating Contact Size Rated Current Contact Resistance miliohms 16 13A 3.46 12 23A 1.83 8 46A 0.52 4 80A 0.26 0 150A 0.14 Service rating Operating Voltage DC at Sea Level Operating Voltage AC at Sea Level Inst. 250V 200V A 700V 500V D 1250V 900V E 1750V 1250V B 2450V 1750V C 4200V 3000V Service rating 5 AMPHENOL MS And 97B Series Insert Orientations To avoid cross-plugging problems in applications requiring the use of more than one connector of the same size and arrangement, alternate insert rotations are available as indicated in the accompanying chart. The following insert arrangements have the same alternate insert rotations for W, X, Y and Z which are as below : Degree As shown in the daigram below, the front face of the pin insert is rotated within the shell in a clockwise direction from the normal shell key. The socket insert would be rotated counterclockwise the same number of degrees with respect to the normal shell key. B B Position W Position X B B A A Position Y Position Z Views looking into front face of pin insert or rear of socket insert Insert Arrangement 12S-3 14S-2 14S-5 14S-7 14S-9 16-9 16-10 16-11 16-13 16S-1 16S-4 16S-5 16S-6 16S-8 18-1 18-3 18-4 18-8 18-10 18-11 18-12 18-15 18-20 18-22 18-29 20-3 20-4 20-5 AMPHENOL Degrees W X Y Z 70 90 70 35 90 35 35 80 35 70 90 70 35 35 70 80 90 70 90 70 45 35 145 120 110 180 145 110 180 110 110 110 145 180 170 145 110 110 120 170 120 180 145 180 145 110 110 215 240 270 215 250 270 250 250 250 215 270 265 215 250 250 240 265 240 270 215 270 215 250 250 290 290 325 325 325 280 325 290 290 325 325 290 280 290 290 325 Insert Arrangement 20-6 20-15 20-17 20-18 20-19 20-21 20-23 20-24 20-27 20-29 22-1 22-2 22-4 22-5 22-8 22-9 22-10 22-11 22-13 22-20 22-22 22-23 22-27 22-28 24-2 24-9 24-10 24-11 X Y Z 80 110 250 280 16-7 20-16 18-5 20-20 18-9 20-22 18-13 22-3 18-14 22-6 20-7 22-12 20-8 22-14 20-9 22-15 20-12 22-16 20-14 22-17 A A W Degrees W X Y Z 70 80 90 35 90 35 35 35 35 80 35 70 35 35 35 70 35 35 35 35 35 80 80 80 35 80 35 145 180 110 180 110 110 110 110 110 145 110 110 110 145 110 110 110 110 110 110 110 215 270 250 270 250 250 250 250 250 215 250 250 250 215 250 250 250 250 250 250 250 250 250 290 280 325 325 325 325 325 280 325 290 325 325 325 290 325 325 325 325 280 280 280 325 280 325 6 22-18 22-19 22-21 22-24 22-25 22-29 22-33 22-34 24-1 24-3 24-4 24-5 24-6 24-7 24-12 24-14 24-16 24-17 24-20 Insert Arrangement 24-22 24-27 28-2 28-3 28-5 28-6 28-7 28-12 28-18 28-22 32-8 36-3 36-4 36-5 36-6 36-9 36-10 36-14 36-15 40-56 24-21 24-28 28-1 28-4 28-8 28-9 28-10 28-11 28-14 28-15 28-16 28-17 28-19 28-20 28-21 32-1 32-3 32-4 36-1 36-7 36-8 36-13 Degrees W X Y Z 45 80 35 70 35 70 35 90 70 70 80 70 70 35 80 80 90 60 72 110 110 145 110 145 110 180 145 145 125 145 145 120 110 125 125 180 125 144 250 250 215 250 215 250 270 215 215 235 215 215 240 250 235 235 270 245 216 280 325 290 325 290 325 290 290 280 290 290 325 280 280 305 288 MS And 97B Series Insert Arrangements Insert Service Total Contact Size Arran- Rating Cont0 4 8 12 16 gement acts 10S-2 A 1 1 10SL-3 A 3 3 10SL-4 A 2 2 12S-3 A 2 2 12S-4 D 1 1 12-5 D 1 1 3 3 14S-1 A 14S-2 Inst 4 4 14S-4 D 1 1 14S-5 Inst 5 5 14S-6 Inst 6 6 14S-7 A 3 3 14S-9 A 2 2 14S-10 Inst 4 4 14S-12 A 3 3 14-3 A 1 1 14S-A7 A 19 19 16S-1 A 7 7 16S-3 B 1 1 16S-4 D 2 2 16S-5 A 3 3 16S-6 A 3 3 16S-8 A 5 5 16-2 E 1 1 16-7 A 3 1 2 16-9 A 4 2 2 16-10 A 3 3 16-11 A 2 2 16-12 A 1 1 16-13 A 2 2 18-1 A/Inst 10 10 18-3 D 2 2 18-4 D 4 4 18-5 D 3 2 1 18-06 6 4 2 18-6 D 1 1 18-7 B 1 1 18-8 A 8 1 7 18-9 Inst 7 2 5 18-10 A 4 4 18-11 A 5 5 18-12 A 6 6 18-13 A 4 1 3 18-14 A 2 1 1 18-15 A 4 4 18-16 C 1 1 18-17 Inst 7 2 5 18-19 A 10 10 18-20 A 5 5 18-22 D 3 3 18-24 A/Inst 10 10 18-29 A 5 5 18-30 A 5 5 18-31 A 5 5 20-2 1 1 20-3 D 3 3 20-4 D 4 4 20-6 D 3 3 20-7 D/A 8 8 Insert Service Total Contact Size Arran- Rating Cont0 4 8 12 16 gement acts 20-8 Inst 6 2 4 20-9 D/A 8 1 7 20-11 Inst 13 13 20-12 A 2 1 1 20-14 A 5 2 3 20-15 A 7 7 20-16 A 9 2 7 20-17 A 6 5 1 20-18 A 9 3 6 20-19 A 3 3 20-20 A 4 1 3 20-21 A 9 1 8 20-22 A 6 3 3 20-23 A 2 2 20-24 A 4 2 2 20-25 Inst 13 13 20-27 A 14 14 20-29 A 17 17 20-30 Inst 13 13 20-33 A 11 11 20-A48 A 19 22-1 D 2 2 22-2 D 3 3 22-4 A 4 2 2 22-5 D 6 2 4 22-6 D 3 2 1 22-7 E 1 1 22-8 E 2 2 22-9 E 3 3 22-10 E 4 4 22-11 B 2 2 22-12 D 5 2 3 22-13 D/A 5 4 1 22-14 A 19 19 22-15 E/A 6 5 1 22-16 A 9 3 6 22-17 D/A 9 1 8 22-18 D/A 8 8 22-19 A 14 14 22-20 A 9 9 22-21 A 3 1 2 22-22 A 4 4 22-23 D/A 8 8 22-24 D/A 6 2 4 22-27 D/A 9 1 8 22-28 A 7 7 22-34 D 5 3 2 24-2 D 7 7 24-3 D 7 2 5 24-4 1 3 24-5 A 16 16 24-6 D/A 8 8 4 2 24-06 A 6 24-7 A 16 2 14 24-9 A 2 2 24-10 A 7 7 7 Insert Service Total Contact Size Arran- Rating Contgement acts 0 4 8 12 16 24-11 24-12 A A 9 5 24-16 24-17 24-20 24-21 24-22 24-27 24-28 28-1 28-2 28-3 28-4 28-5 28-6 28-7 28-8 28-9 28-09 28-10 28-11 28-12 28-13 28-15 28-16 28-17 28-18 28-19 28-20 28-21 28-22 28-51 32-1 32-3 D/A D D D D E Inst D/A D E E/D D D D E/D/A D A D/A A A A A A B/D/A C/D/A/Inst B/D/A A A D D D/A D 7 5 11 10 4 7 24 9 14 3 9 5 3 2 12 12 9 7 22 26 26 35 20 15 12 10 14 37 6 12 5 9 D 32-5 A 32-6 32-7 INST,A 32-8 A 32B-13 D D 32-17 A 32-22 2 23 35 30 13 4 54 36-1 36-3 36-4 36-5 36-6 36-7 36-8 36-9 36-10 36-11 36-12 36-13 36-14 36-15 36-16 36-17 38-18 36-20 36-46 36-52 40-56 40-63 22 6 3 4 6 47 47 31 48 48 48 17 16 35 47 47 31 34 27 52 85 61 D D D/A A A A A A A A A E/A D D/A A A A A A A A A 3 2 1 3 2 2 1 4 6 3 3 3 9 9 7 24 3 6 2 12 3 2 1 2 3 2 4 2 2 3 2 1 2 7 2 2 10 6 6 5 3 4 18 26 26 35 20 15 12 4 6 10 4 37 3 12 3 2 4 2 2 3 2 16 7 28 6 24 13 4 54 3 3 4 2 4 18 3 4 1 1 7 40 1 46 2 14 14 48 48 48 2 15 5 5 6 35 7 40 7 40 2 14 14 2 2 30 27 52 85 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND B A A 16 B C 12 8 0 4 A B Insert arrangement Service rating Number of contacts Contact size Premating contact Front of socket insert 10SL-3 A 3 16 C 10S-2 A 1 16 G 10SL-4 A 2 16 14S-1 C A A F E Front of socket insert B C 12S-3 A 2 16 A B C B 14S-2 Inst. 4 16 14S-1 A 3 16 B A 14S-4 D 1 16 14S-7 A 3 16 B D C A B C 14S-9 A 2 16 B 100 0 rotation of 14S-2 100 0 rotation of 14S-7 *14S-10 Inst. 4 16 *14S-12 A 3 16 B A C 16S-4 D 2 16 AMPHENOL 8 B C 16S-1 A 7 16 G E C A D B 16S-5 A 3 16 A *Not tooled up, can be tooled up on request. Contact Factory. *14-3 A 1 8 A G D B *16S-3 B 1 16 14S-6 Inst. 6 16 E A B A Insert arrangement Service rating Number of contacts Contact size Premating contact 14S-5 Inst. 5 16 F A B Insert arrangement Service rating Number of contacts Contact size Premating contact C D C 14S-A7 A 7 16 C E B D D Insert arrangement Service rating Number of contacts Contact size Premating contact A F A E D B 12-5 D 1 12 12S-4 A 1 16 16S-6 A 3 16 B C A B 16S-8 A 5 16 E *16-2 E 1 12 MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A B A C D H A A F J 16-9 A 2 2 12 16 16-10 A 3 12 B D B C 16-11 A 2 12 16-12 A 1 4 A C B *16-13 A 2 12 E A A C A B B F D C B D E Insert arrangement 18-1 Service rating B,C,F,G=A;Bal.=Inst. Number of contacts 10 Contact size 16 Premating contact F A E G D *18-6 D 1 4 18-06 A 2 4 16 12 E B B 18-5 D 2 1 12 16 C C E H D 18-4 D 4 16 A 18-3 D 2 12 G F A D A C B C 18-7 B 1 8 F A D B C E A D B D 18-8 A 1 7 12 16 H 18-9 Inst. 2 5 12 16 18-10 A 4 12 D 18-11 A 5 12 E F A B B 18-12 A 6 16 C or D A C B B E D B G D C D E A C C Insert arrangement Service rating Number of contacts Contact size Premating contact A B B A I 0 4 B C 16-7 A 1 2 8 16 C G 8 B C Insert arrangement Service rating Number of contacts Contact size Premating contact 12 16 *18-13 A 1 3 8 12 A E C A G F B D A A H J C K o 100 - rotation of 18-9 Insert arrangement Service rating Number of contacts Contact size Premating contact *18-14 A 1 1 4 16 18-15 A 4 12 18-16 C 1 12 *18-17 Inst. 2 5 12 16 18-19 A 10 16 K 18-20 A 5 16 D *Not tooled up, can be tooled up on request. Contact Factory. 9 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND H C B A A B A G I B F J C C D E E E H 20-3 D 4 12 A A A H G F B B B H C F B 20-2 D 1 0 - C B G B C *18-31 A 5 16 C A C A 260 rotation of 18-20 110 rotation of 18-20 *18-30 A 5 16 C *18-29 A 5 16 D A A 0 0 - 0 - *18-24 B,C,F,G=A;Bal.=Inst. 10 16 D 4 D D 250 - rotation of 18-1 18-22 D 3 16 C 8 B A C D o Insert arrangement Service rating Number of contacts Contact size Premating contact B A 12 C E E 16 G J C F C C E B D E A D D E F D Insert arrangement Service rating Number of contacts Contact size Premating contact 20-4 D 4 12 C or D L B E M N 20-7 A,B,H,G=D;C,D,E,F=A 8 16 A *20-6 D 3 16 A G F A D D G E A B H K 20-9 H=D;Bal.=A 1 7 12 16 H I D C D 20-11 Inst. 13 16 A H G F D B C B C F 20-18 A 3 6 12 16 D 20-19 A 3 8 C 20-20 A 1 3 4 12 A *Not tooled up, can be tooled up on request. Contact Factory. AMPHENOL 10 20-16 A 2 7 12 16 E A F C B 20-17 A 5 1 12 16 E or F F A H G B D Insert arrangement Service rating Number of contacts Contact size Premating contact A C E 20-15 A 7 12 A or D A A I D B 20-14 A 2 3 8 12 D *20-12 A 1 1 4 16 H C C Insert arrangement Service rating Number of contacts Contact size Premating contact E G E B B J 20A - 9 A 9 12 F A F E A C 20-8 Inst. 2 4 8 16 A B I E C D E A B D B C *20-21 A 1 8 12 16 1 20-22 A 3 3 8 16 20-23 A 2 8 MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND L A J B N G B D F A D K I M J L F C 0 L C E F N G P S C B M D T H K E A D R J D 4 B N K E G C A L H 8 M B N H K 12 A C E M 16 J F H G _ 0 100 rotation of 20-11 Insert arrangement Service rating Number of contacts Contact size Premating contact 20-24 A 2 2 8 16 *20-25 Inst. 13 16 B M U K C H *20-30 Inst. 13 16 B D P C J D H E R S A A N V T L F 20-29 A 17 16 G 20-27 A 14 16 M L M A A K J o 250 rotation of 20-11 B A C B B C D G F E Insert arrangement Service rating Number of contacts Contact size Premating contact 20-33 A 11 16 E F 20 A - 48 A 19 16 22-2 D 3 8 A *22-4 A 2 2 8 12 C A A E 22-1 D 2 8 A B B B A C C D Insert arrangement Service rating Number of contacts Contact size Premating contact 22-5 D 2 4 12 16 D 22-7 E 1 0 *22-6 D 2 1 8 16 B A E B C 22-9 E 3 12 A *22-8 E 2 12 A D B K A J U C C 22-12 D 2 3 8 16 A 22-13 E=D;A,B,C,D=A 4 1 12 16 E C R H D G 22-11 B 2 16 B P S B A N Y T B 22-10 E 4 16 C M L A D E D Insert arrangement Service rating Number of contacts Contact size Premating contact B C F E 22-14 A 19 16 A *Not tooled up, can be tooled up on request. Contact Factory. 11 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 A F H G B F C C Insert arrangement 22-15 Service rating D=E;A,B,C,E,F=A Number of contacts 5 1 Contact size 12 16 Premating contact D E D E 22-16 A 3 6 12 16 D *22-17 A=D;Bal.=A 1 8 12 16 E D B 22-19 A 14 16 F E B H E F A F 22-27 J=D;Bal.=A 1 8 8 16 A B B G E E D 22-28 A 7 12 G C A C D D B G E C B 24-4 A D D C H J D C A H F B K M L G B E G F C D F 22-24 C,D,E=D;A,B,F=A 2 4 12 16 D B C G 22-23 H=D;Bal.=A 8 12 A or D G E C D 22-22 A 4 8 C or D A B J D C *22-21 A 1 2 0 16 22-20 A 9 16 D F B E B Insert arrangement Service rating Number of contacts Contact size Premating contact D A F F H C C F A A A B E E C 22-18 A,B,F,G,H=D;C,D,E=A 8 16 D G A C D G D A J F N D H G C M H B F J F E D P 0 B L J H C J A K A G A G E B A H B 4 N A P E D C R S Insert arrangement Service rating Number of contacts Contact size Premating contact *22-34 D 3 2 12 16 E 24-2 D 7 12 A *24-3 D 2 5 12 16 D *Not tooled up, can be tooled up on request. Contact Factory. AMPHENOL 12 24-4 A 3 1 16 0 - 24-5 A 16 16 S 24-6 A,G,H=D;Bal.=A 8 12 D MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND D E A L A K J 12 8 F B C M P 16 0 A A B C A B E N 4 B G D D E F O E I D B C 24-06 Insert arrangement Service rating Number of contacts Contact size Premating contact 24-7 A 2 14 12 16 G 24-9 A 2 4 D E B A *24-16 A,B,F,G=D;C,D,E=A 1 3 3 8 12 16 G 24-12 A 2 3 4 12 D *24-17 D 2 3 12 16 D A A A F B E K G C B E F L B G M C H N E E D H A 24-21 D 1 9 8 16 E K B Q J G C R S T W X U V P Y Z G F B M 24-28 Inst. 24 16 *24-27 E 7 16 D C D N D E 24-22 D 4 8 D H A L J C D Insert arrangement Service rating Number of contacts Contact size Premating contact D 24-20 D 2 9 12 16 A J P K F D F B C J L G D A H G C K C 24-11 A 3 6 8 12 E B H G E C A J C B F 24-10 A 7 8 D or E or G D A A B Insert arrangement Service rating Number of contacts Contact size Premating contact I H G 24-06 A 2 4 16 8 E G C F H 28-1 A,J,E=D;Bal.=A 3 6 8 12 E E F *28-2 D 2 12 12 16 E *Not tooled up, can be tooled up on request. Contact Factory. 13 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A A S A B A B E C P C D C B B E G F C D Insert arrangement Service rating Number of contacts Contact size Premating contact 28-3 E 3 8 A *28-5 D 2 1 2 4 12 16 *28-4 G,S,P=E;Bal.=D 2 7 12 16 E J H H A A G M A B 28-6 D 3 4 A B F L C A K G B M B D L C D 28-7 D 2 4 Insert arrangement Service rating Number of contacts Contact size Premating contact U G B V W X P R S L N A F B M C L H D Z X J C U N G C D E F b Z M A B S a T d V W H R P B T d Y K A b H G 28-09 A 5 4 16 4 S a G T M I D R P E K J D 28-9 D 6 6 12 16 E J N E E 28-8 L,M=E;B=D;Bal.=A 2 10 12 16 D A F F E C F E L Y K X U H G o F 100 rotation of 28-12 Insert arrangement Service rating Number of contacts Contact size Premating contact 28-10 G=D;Bal.=A 2 2 3 4 8 12 G 28-11 A 4 18 12 16 M *Not tooled up, can be tooled up on request. Contact Factory. AMPHENOL 14 28-12 A 26 16 H *28-13 A 26 16 H D E W J C V MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A J H A B E D C L K M e f g N M H C S H V N U R Q P G F E 8 4 E 0 A L B K L F K C R M P J M D N E H k l F m G 28-15 A 35 16 M 28-16 A 20 16 F J A N K A B G 28-19 H,M=B;A,B=D;Bal.=A 4 6 12 16 H D A F N V P W R X Z a b c d e Y B f g l h m j k n p E 28-21 A 37 16 A A B J M U 28-20 A 10 4 12 16 E A H L T E K C G K S D H N F C L M G F H E P E M J J B C H C K 28-18 M=C;G,H,J,K,L=D;A,B=ABal.=Inst. 12 16 *28-17 R=B;M,N,P=D;A to L=A 15 16 N B A L Insert arrangement Service rating Number of contacts Contact size Premating contact C D J 12 D h j Insert arrangement Service rating Number of contacts Contact size Premating contact L T A G PX R Y S Z T a U b V c W d B B K J G F 16 A E B B D E L D 28-22 D 3 3 4 16 C F M F C G D E D J C H Insert arrangement Service rating Number of contacts Contact size Premating contact 28-51 D 12 12 32-1 A=E;B,C,D,E=A 2 3 0 12 *32-3 D 1 2 2 4 0 4 12 16 32-5 D 2 0 *Not tooled up, can be tooled up on request. Contact Factory. 15 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND A B G H K L P W X J M N S Z T O h R K S L F e j X W f g X Z T a U 4 0 A G B M k Y V U 8 E R d Y 12 J c F I P W D C E 16 H C N D I b V Insert arrangement Service rating Number of contacts Contact size Premating contact O 32-7 INST , A 4 24 7 16 12 32-6 A 16 2 3 2 16 12 8 4 A M T Y D N c Z V P a e X e i l AA z AD 10 1 A B C E F G A F D 11 13 H B 2 12 J I 8 K L M N E 3 32B13 O 7 Insert arrangement Service rating Number of contacts Contact size Premating contact 5 32B-13 D 13 8 R S U V W *36-1 D 4 18 12 16 *Not tooled up, can be tooled up on request. Contact Factory. AMPHENOL P T D C 4 6 AC AE AG 32-22 A 54 16 32-17 D 4 4 32-8 A 6 24 12 16 S 9 w y AF Insert arrangement Service rating Number of contacts Contact size Premating contact r v AB B C 16 f j n m x S W a Z d h o L X R Y Y c k C G R P U g F K W b J M O T b B J H L N E O d G K S B D F A I U C A D H 36-3 D 3 3 0 12 MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A A A B F B D C B E C C Insert arrangement Service rating Number of contacts Contact size Premating contact 36-4 A=D;B,C=A 3 0 A C K O P R V a h Y d Z e S T b f W x A H O V J P W d K Q X e l Y m t R f N a p H U b j r w C T h v y M Z n G S g u A F L O c V k s J P W d r f Q e n z y M j c k s x V D J P W d Q X R f m t F L Y e l B E K Z n N T a h p v y G M S g u z 100 rotation of 36-10 *36-11 A 48 16 A 36-10 A 48 16 A O U b r w H N a p C T h v G N A Z C F L T G S g u X c *36-9 A 1 2 14 14 4 8 12 16 P F L Y m t R B R f K W b w z E K X l x D o Insert arrangement Service rating Number of contacts Contact size Premating contact B e *36-8 A 1 46 12 16 Y B E H t y A P e p v E J V j u *36-7 A 7 40 12 16 x or y D k n s D I O Y a d h M U a d L R V Z m y C Y g z Insert arrangement Service rating Number of contacts Contact size Premating contact K P U M c f s y S Z H X b m p vv w r J O T N S c g k u I X j n N 36-6 A 2 4 0 4 C E F G W l A B D E G J M I U 36-5 A 4 0 B D F H L D j r w U b c k s x z o 250 rotation of 36-10 *36-12 A 48 16 A *Not tooled up, can be tooled up on request. Contact Factory. 17 AMPHENOL MS And 97B Series Insert Arrangements Front face of pin insert or rear of socket insert illustrated CONTACT LEGEND 16 12 8 4 0 A J P S R B N K L P P M R S H B E W g Y X F G K J E D V f h Z G E F e m L D G D M C Q H a M N J C U j b N L T d k c C Q A K A B Q I H F Insert arrangement Service rating Number of contacts Contact size Premating contact A D C F H L P K O U Y d h Z e B E I R V W l w u F H L P U X Y d c g k v h m Z e S E R V W G J M S N T l w g v I J B f b W c X K R T A C H P R X d D J Y T Z *36-16 A 7 40 12 16 x or y *36-17 A 7 40 12 16 x or y *36-18 A 1 2 14 16 4 8 12 16 A U N V b e J W R H P N A E F L M L E T K g W U V T B F M U C H N V D J P W A X Y S b j c k d m f n g p h t AC Z d Y c s X t u v w i j u v z AA AB AC AD AE AF AH M V U d c W f p n g r p AD AE AF w x y z AH AJ AK AL AA Z s AB AM AN x AP y b b m k L K T h r j m i J S a Z D C H R Y X Z q P N S B F E K R W a a k B G c f h C D G M a AR AZ AS BA BJ AT BB BK X AU BC LB BS AV BT AW BD BM BE BN BU AX BF BP BV AY BH BR Y 40 - 56 Insert arrangement Service rating Number of contacts Contact size Premating contact *36-20 A 2 2 30 8 12 16 k 36-46 A 27 16 36-52 A 52 16 *Not tooled up, can be tooled up on request. Contact Factory. AMPHENOL G 100orotation of 36-9 F L F 250 rotation of 36-7 B E K S o L N 100 rotation of 36-7 Insert arrangement Service rating Number of contacts Contact size Premating contact 18 A H p z o D E e s y V M O Y m y z U a P c k u d Z X b f a r y y B I j n p s r A D C K O N T b f a j n G J M S *36-15 M=D;Bal=A 35 16 J *36-14 D 5 5 6 8 12 16 *36-13 N,P,Q=E;Bal.=A 2 15 12 16 40-56 A 85 16 40-63 A 61 16 C MS And 97B Series Shell Types Wall mounting receptacle MS-3100 MOUNTING HOLES 4.39 DIA. FOR SIZE 32 AND 36 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES 4.55 DIA. FOR 40 SIZE MS-4100 M K V S R S PANEL OPENING R A All dimensions are in mm Connector Size A Thread in inches K M O R S V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2.00-18 UNS 2 1/4-16 UN 2 1/2-16 UN 1.98 1.98 1.98 1.98 1.98 1.98 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.45 14.29 14.29 19.05 14.29 19.05 14.29 19.05 19.05 19.05 19.05 20.64 20.64 22.25 22.22 22.22 20.62 20.62 20.62 23.82 23.82 26.97 26.97 30.17 33.32 36.52 39.67 46.02 53.0 58.72 62.00 18.25 20.64 20.64 23.02 23.02 24.61 24.61 26.99 29.37 31.75 34.92 39.69 44.45 49.21 55.58 25.68 27.76 27.76 30.43 30.43 32.82 32.82 35.07 38.38 41.55 44.70 51.08 57.15 63.78 69.85 5/8-24 NEF 11/16-24NEF 11/16-24NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN Cable Connecting Receptacle MS-3101 MS-4101 V A All dimensions are in mm Connector Size A Thread in inches V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN 19 AMPHENOL MS And 97B Series Shell Types Box mounting receptacle MS-3102 MOUNTING HOLES 4.39 DIA. FOR SIZE 32 AND 36 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES 4.55 FOR 40 SIZE MS-4102 L S N R S M K R A All dimensions are in mm Connector Size A Thread in inches K L M N R S 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 1.98 1.98 1.98 1.98 1.98 1.98 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.17 3.45 30.18 30.18 41.28 30.18 41.28 30.18 41.28 49.28 49.28 49.28 49.28 49.28 49.28 49.28 49.28 13.89 14.28 19.05 14.28 19.05 14.28 19.05 19.05 19.05 19.05 20.64 20.64 22.22 22.22 22.22 15.87 17.46 17.46 19.05 19.05 22.22 22.22 25.40 28.57 31.75 34.92 41.27 48.26 53.97 58.25 18.25 20.64 20.64 23.02 23.02 24.61 24.61 26.99 29.37 31.75 34.92 39.69 44.45 49.21 55.58 25.68 28.04 28.04 30.43 30.43 32.82 32.82 35.08 38.38 41.55 44.73 51.08 57.15 63.78 69.85 Straight Plug MS-3106 Q MS-4106 V A All dimensions are in mm Connector Size A Thread in inches Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 UN 2 1/2-16 UN 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 63.50 5/8-24 NEF 11/16-24NEF 11/16-24NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-20 UN Note - Both versions, straight and diamond knurling available on coupling ring. For details, contact factory. AMPHENOL 20 MS And 97B Series Shell Types Right angle plug MS-3108 MS-4108 Q max A THREAD V All dimensions are in mm Connector Size A Thread in inches Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1-20 UNEF 1 1/8-18 UNEF 1 1/4-18 UNEF 1 3/8-18 UNEF 1 1/2-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4-16 NS 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 29/32-18 NS 2 1/16-20 UNS 40 2 1/2-16 UN 63.50 2 5/16-16 UN Note - Both versions, straight and diamond knurling available on coupling ring. For details, contact factory. Shell Types Box mounting receptacle S R A 97B-3100 97B-4100 R K V MOUNTING HOLES 4.39 DIA. FOR SIZE 32 , 36 AND 40 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES S M All dimensions are in mm A K M R S V Thread in inches 10SL 14S 16S 16 18 20 22 24 28 32 36 18.2 24.6 27.4 27.4 30.8 34.2 37.4 40.9 46.7 53.4 59.6 2.8 3.2 3.2 3.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0 14.2 14.2 14.2 19.0 19.0 19.0 19.0 20.6 20.6 22.2 22.2 18.2 23.0 24.6 24.6 27.0 29.4 31.8 34.9 39.7 44.5 49.2 25.4 30.0 32.5 32.5 35.0 38.0 41.0 44.5 50.8 57.0 63.5 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-24 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 40 65.5 4.0 22.2 55.5 69.85 2 5/16-16 UN Connector Size 21 AMPHENOL MS And 97B Series 97B-4101 A 97B-3101 Q M Cable Connecting Receptacle K V All dimensions are in mm Connector Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 A K M 18.2 24.6 27.4 27.4 30.8 34.2 37.4 40.9 46.7 53.4 59.6 65.5 2.8 3.2 3.2 3.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 14.2 14.2 14.2 19.0 19.0 19.0 19.0 20.6 20.6 22.2 22.2 22.2 V Thread in inches 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-24 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UNS Shell Types MOUNTING HOLES 4.39 DIA. FOR SIZE 32 ,36 AND 40 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES Front box mounting receptacle 97B-3102 97B-4102 M S R A N S R K L All dimensions are in mm Connector Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 AMPHENOL A K M R S 18.2 24.6 27.4 27.4 30.8 34.2 37.4 40.9 46.7 53.4 59.6 65.5 2.8 3.2 3.2 3.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 14.2 14.2 14.2 19.0 19.0 19.0 19.0 20.6 20.6 22.2 22.2 22.2 18.2 23.0 24.6 24.6 27.0 29.4 31.8 34.9 39.7 44.5 49.2 55.5 25.4 30.0 32.5 32.5 35.0 38.0 41.0 44.5 50.8 57.0 63.5 69.85 22 N max L max 15.9 19.2 22.4 22.4 25.6 29.0 32.2 35.3 41.4 47.8 52.4 58.70 24.7 24.7 24.7 33.8 34.5 34.5 34.5 35.7 35.7 37.3 37.3 37.3 MS And 97B Series Back Box Mounting Receptacle 97B-3103X* / 97B-4103X* M `L' R A S R K V S 97B-3103 / 97B-4103 MOUNTING HOLES 4.39 DIA. FOR SIZE 32 , 36 AND 40 3.73 DIA. FOR SIZE 24 AND 28 3.05 DIA. FOR ALL OTHER SIZES * Replace X with Required Class All dimensions are in mm A K M R S V Thread in inches 18.2 24.6 27.4 27.4 30.8 34.2 37.4 40.9 46.7 53.4 59.6 65.5 2.8 3.2 3.2 3.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 18.2 18.2 18.2 21.5 23.05 23.05 23.05 23.05 24.05 24.05 24.05 24.05 18.2 23.0 24.6 24.6 27.0 29.4 31.8 34.9 39.7 44.5 49.2 55.5 25.4 30.0 32.5 32.5 35.0 38.0 41.0 44.5 50.8 57.0 63.5 69.85 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-24 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN Connector Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 L REF. 27.60 33.81 35.71 37.31 2 5/16-16 UN-2A Shell Types Straight plug 97B-3106 97B-4106 Q V All dimensions are in mm Connector Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 Q max V Thread in inches 22.8 29.2 32.0 32.0 36.5 39.9 43.1 46.6 53.4 60.1 66.3 69.10 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN 23 AMPHENOL MS And 97B Series L Right Angle Plug 97B-3108 97B-4108 Q max K V All dimensions are in mm Connector Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 Q max V Thread in inches L max K max 22.8 29.2 32.0 32.0 36.5 39.9 43.1 46.6 53.4 60.1 66.3 69.10 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 29/32-18 NS 2 1/16-20 UNS 2 5/16-16 UN 45 47 48 57 58 61 61 66 66 72 75 78 30 30 30 35 35 35 35 40 40 45 50 55 Note - Both versions, straight and diamond knurling available on coupling ring. For details, contact factory. Shell Types Jam nut receptacle 97B - 3107R 97B-4107R L K S H NUT 236 MAX. PANEL THICKNESS D W A S O-RING B THREAD G M J All dimensions are in mm Shell Size A Ref. D Ref. G Ref. H Ref. J Ref. K Ref. L Ref. M Ref. S +- 0.3 W Ref. 10SL 14S 16S 16 18 20 22 24 28 32 36 18.2 24.6 27.4 27.4 30.8 34.1 37.3 40.8 46.7 53.3 59.6 2.5 2.5 2.5 2.5 3.0 3.0 3.0 3.0 3.0 3.0 3.0 35.0 41.3 44.4 44.4 48.2 52.4 55.5 59.0 66.0 72.0 80.0 31.5 37.9 41.0 41.0 44.8 49.0 52.2 55.0 62.0 68.0 75.0 13.5 13.5 13.5 13.5 15.0 15.0 15.0 15.0 15.0 15.0 15.0 3.2 3.2 3.2 3.2 4.0 4.0 4.0 4.0 4.0 4.0 4.0 29.2 29.2 29.2 37.7 40.0 40.0 40.0 40.0 40.0 40.0 40.0 12.5 12.5 12.5 21.0 21.0 21.0 21.0 21.0 21.0 21.0 21.0 31.8 38.1 41.2 41.2 45.0 49.2 52.4 55.2 62.2 68.2 75.2 5.0 6.0 6.0 6.0 7.0 7.0 7.0 7.0 7.0 7.0 8.0 AMPHENOL 24 MS And 97B Series Shell Types Jam nut receptacle 97B - 3107 97B-4107 L S G M J P G S N R V B O-Ring All dimensions are in mm Shell Size G +- 0.3 10SL 14S 16S 16 18 20 22 24 28 32 36 40 11.2 14.6 15.7 15.7 16.8 18.0 20.0 20.2 22.5 24.7 26.9 29.6 J Wall Thickness Min. Max. 2.4 5.2 2.4 7.5 2.4 7.5 2.4 7.5 2.4 9.0 2.4 9.1 2.4 9.1 2.4 9.1 2.4 10.0 2.4 10.0 2.4 8.3 2.4 8.3 L +- 0.3 M +- 0.3 36.2 38.9 38.9 48.5 49.3 49.3 49.3 49.6 51.9 51.9 51.9 51.9 24.5 26.8 26.8 32.1 33.7 33.7 33.7 33.7 35.2 35.2 35.2 35.2 N +0.00 -0.15 18.2 24.6 27.4 27.4 30.8 34.2 37.4 40.9 46.7 53.4 59.6 65.5 Shell Types Panel mounting plug connector 97B - 3110X 97B-4110X L3 P +- 0.2 R +-0.4 S +- 0.3 Thread in inches 4.0 4.8 4.8 4.8 4.8 4.8 4.8 4.8 5.6 5.6 5.6 5.6 27 33 38 38 40 44 51 51 56 62 71 76 31.8 41.3 44.4 44.4 47.6 50.8 57.2 57.2 63.5 69.8 76.2 82.5 5/8-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1.7/8-16UN 2 1/16-20 UNS 2 5/16-16 UN e LP L4 L4 d2 e L1 All dimensions are in mm Shell Size 10SL 14S 16S 16 18 20 22 24 28 32 36 40 d1 d2 Max H13 22.8 29.2 32 32 36.5 39.9 43.1 46.6 53.4 60.1 66.3 72.5 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.7 3.7 4.3 4.3 4.3 e +- 0.1 18.2 23 24.6 24.6 27 29.4 31.8 34.9 39.7 44.5 49.2 55.5 25 l1 ~ 28.1 28.1 28.1 37.6 38.6 38.6 38.6 41 41.8 45 45 45 l3 +- 0.2 l4 +- 0.3 2.8 3.2 3.2 3.2 4 4 4 4 4 4 4 4 25.4 30 32.5 32.5 35 38 41 44.5 50.8 57 63.5 69.9 AMPHENOL MS And 97B Series Back Accessories Solid backshell without grommet and sleeve Class A Q L V A All dimensions are in mm A Thread in inches L max for MS L max for 97B Q max V Thread in inches 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 32.54 37.31 46.83 36.51 46.83 37.70 48.02 50.80 53.97 53.97 57.15 57.15 59.0 60.32 71.80 37.60 ----37.64 --38.83 48.00 51.58 54.75 54.75 57.94 57.94 59.78 61.13 80.00 19.05 19.84 19.84 22.22 22.22 25.40 25.40 28.57 31.75 34.92 38.10 44.45 51.75 57.15 63.50 5/8-24 UNEF 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4 - 16 UN Connector Size 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 2 5/16-16 UN Solid Backshell With Grommet & Sleeve Class R Q L A All dimensions are in mm Connector Size 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 A Thread class 2B in inches 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-16 UN For Plug type L max for MS 47 47 55 47 55 47 55 57 57 57 57 57 58.25 58.25 58.25 For Receptacle L max for 97B 48 ----48 --48 56 57 57 57 57 57 60 60 60 Note - Both versions, straight and diamond knurling available on back accessories. For details, contact factory. AMPHENOL 26 Q max 21.50 20.35 20.35 23.40 23.40 26.71 26.71 29.50 35.70 35.85 44.40 45.08 52.36 56.81 64.50 MS And 97B Series Back Accessories Strain relief backshell with grommet and sleeve Class E and F N L A All dimensions are in mm A Thread class 2B in inches L max for MS L max for 97B N max 5/8-24 NEF 11/16-24 NEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 54.07 54.07 55.90 55.90 64.41 65.94 67.41 67.41 73.28 73.28 74.75 74.75 86.0 59.10 --61.34 62.86 21.97 21.97 25.15 28.45 28.45 30.76 37.29 37.29 44.45 44.45 52.22 57.15 67.10 Connector Size 10SL 12S 14S 16S 16 18 20 22 24 28 32 36 40 2 5/16-16 UN 71.10 72.55 72.55 76.82 77.82 77.64 125.0 Right Angle Backshell With Or Without Grommet Class A, F & R L1 Q L A V All dimensions are in mm Connector Size A Thread class 2B in inches L max for MS L max for 97B L1 max Q max V Thread in inches 10SL 12S 12 14S 14 16S 16 18 20 22 24 28 32 36 40 5/8-24 NEF 11/16-24 NEF 11/16-24 NEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 1/8-18 NS 1 1/4-18 NEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16UN 2 1/16-16UN 2 5/16-26 UN 37.60 37.80 47.30 39.40 48.90 42.60 52.10 53.70 58.80 58.80 63.60 63.60 69.60 72.80 76.00 45.00 ----47.00 --48.00 57.00 58.00 61.00 61.00 66.00 66.00 72.00 75.00 78.00 25.00 25.00 25.00 27.00 27.00 28.00 28.00 31.00 34.00 34.00 37.00 39.00 45.00 48.00 55.00 22.22 25.40 25.40 28.57 28.57 31.75 31.75 34.13 37.30 40.48 43.66 50.00 56.50 62.71 62.71 5/8-24 UNEF 5/8-24 UNEF 5/8-24 UNEF 3/4-20 UNEF 3/4-20 UNEF 7/8-20 UNEF 7/8-20 UNEF 1-20 UNEF 1 3/16-18 UNEF 1 3/16-18 UNEF 1 7/16-18 UNEF 1 7/16-18 UNEF 1 3/4-18 UNS 2-18 UNS 2 1/4 -16 UN Note - Both versions, straight and diamond knurling available on back accessories. For details, contact factory. 27 AMPHENOL MS And 97B Series `O' Ring G PG B A PG Adaptor L Shell size G Thread in inches 10SL 12S 14 16 18 20 22 24 28 36 5/8-24 11/16-24 3/4-20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 5/8-18 2 1/8-18 PG 9 A 30 B 21 PG 11 L 26 PG 13 PG 16 A B L A B L 23 25 30 35 23 25 26 26 30 30 37 40 23 23 30 PG 21 A B L 25 30 35 35 25 28 28 28 30 37 40 40 PG 29 A B L 35 35 38 45 35 35 35 37 40 40 40 45 A B L A B L 40 45 57 40 45 44 40 45 55 57 57 55 Ordering Information MS - XX-PGYY Where XX- Shell Size YY-PG-Thread Size EGM/PHM Backshell Accessories L G `O' RING EGM INNER METAL FERRULE PLASTIC CDMB RUBBER BUSH D GLAND NUT EGM BACKSHELL Shell size G Thread in inches 10SL 5/8"-24 11/16"-24 3/4"-20 7/8"-20 1"-20 1.1/8"-18 1.1/4"-18 1.3/8"-18 1.29/32"-18 2.1/6"-18 12SL 14 16 18 20 22 24 32 36 EGM/PHM 11 D 25.00 25.00 25.00 25.00 29.00 31.50 L 37.00 37.00 37.00 40.00 40.00 52.00 35.00 35.00 52.00 52.00 60.00 60.00 70.00 70.00 Note:- Rubber Bush supplied in Packing In case of PHM inner metal Furrele is not required/supplied EGM/PHM11 Can accept cable Min. 5.70 mm & Max. 10.85 mm EGM/PHM21 Can accept cable Min. 12.70 mm & Max. 17.85 mm AMPHENOL 28 EGM/PHM 21 D 27.00 27.00 27.00 27.00 31.00 33.50 35.00 35.00 52.00 52.00 L 41.00 41.00 41.00 43.00 43.00 55.00 60.00 60.00 70.00 70.00 PG 36 MS And 97B Series Heat Shrink Boot adaptor (G) C A B 3.50+0.20 L B L Max. C- THD 20.30 30.00 5/8-24 NEF 22.30 27.00 3/4-20 UNEF 13.50 24.80 29.50 7/8-20 UNEF 14.60 18.70 20.80 24.60 27.00 33.30 38.50 48.20 28.50 Shell size A Min. 10SL 7.70 8.20 10.60 12S 14S 16S 16 18 20 22 24 28 32 36 40 1-20 UNEF 1 1/8-18 NEF 1 1/4-18 UNEF 1 3/8-18 NEF 1 5/8-18 NEF 1 7/8-16 UN 2 1/16-16 UN 2 5/16-16 UN 33.50 34.50 35.10 41.00 44.80 51.50 56.00 62.00 35.70 34.00 34.10 34.20 34.20 36.60 Back Accessories Cable clamp MS-3057 Use MS-3420 sleeves B C A All dimensions are in mm Part number Shell size Max OD of cable A B C Thread in inches MS-3057-4A 10SL, 12S 5.59 20.90 21.39 7.94 5/8-24 MS-3057-6A 14, 14S 7.92 21.59 25.27 11.11 3/4-20 MS-3057-8A 16, 16S 11.10 23.37 28.45 14.29 7/8-20 MS-3057-10A 18 14.27 23.37 30.89 15.87 1-20 23.07 35.03 19.50 1 3/16-18 23.81 1 7/16-18 MS-3057-12A 20,22 15.87 MS-3057-16A 24,28 19.05 25.78 42.75 MS-3057-20A 32 23.80 28.00 51.00 31.70 1 3/4-18 MS-3057-24A 36 31.75 29.36 57.02 34.92 2-18 29 AMPHENOL MS And 97B Series Neoprene Sleeve MS-3420 Rubber bushing. Protects wire bundles and unjacketed cables from possible damage by cable clamp. D F B A C E 45 0 All dimensions are in mm E Rad in inches Part number A MS-3420-3 3.30 5.33 9.50 73.02 0.79 F Rad in inches 0.79 MS-3420-4 5.59 7.67 12.70 69.85 0.79 0.79 1.59 B C D MS-3420-6 7.92 10.84 15.59 66.67 0.79 MS-3420-8 11.10 14.02 18.77 63.50 1.59 1.59 MS-3420-10 14.27 15.62 21.94 60.32 1.59 1.59 MS-3420-12 15.87 18.80 26.23 56.20 1.59 1.59 MS-3420-16 19.05 23.54 26.39 53.97 1.59 1.59 MS-3420-20 23.80 31.50 40.41 50.80 1.59 1.59 MS-3420-24 31.75 34.67 46.79 47.62 1.59 1.59 Other Accessories Plain flat gasket For MS and 97B flange mounted receptacles B A O C C A OD 4 HOLES T All dimensions are in mm Part number Shell size A max B C D MS-101000 MS-108686 MS-101001 MS-101002 MS-101003 MS-101004 MS-101005 MS-108687 MS-101006 MS-108688 MS-101007 MS-110831 10SL 12S & 12 14S & 14 16S & 16 18 20 22 24 28 32 36 40 18.26 20.62 23.01 24.61 27.00 29.36 31.75 34.90 39.70 44.45 49.22 55.77 15.90 19.05 22.20 25.40 28.57 31.75 34.90 38.10 44.45 50.80 55.57 61.92 25.40 27.80 30.15 32.50 34.90 38.10 41.20 44.45 50.80 57.15 63.50 69.85 4.35 4.35 4.35 4.35 5.15 5.15 5.15 5.15 5.15 5.55 5.55 5.55 AMPHENOL 30 T 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 MS And 97B Series Protective Cap For MS Series MS-25043 For receptacles Has internal threads and is used on all receptacles. Gasket is provided in the dust cap forming a watertight seal. D C MAX A B MAX E All dimensions are in mm MS Part number Shell size A Thread in inches B C D E MS 25043-10D MS 25043-12D MS 25043-14D MS 25043-16D MS 25043-18D MS 25043-20D MS 25043-22D MS 25043-24D MS 25043-28D MS 25043-32D MS 25043-36D MS 25043-40D MS 10S-1-SL MS 12-12S MS 14-14S MS 16-16S MS 18 MS 20 MS 22 MS 24 MS 28 MS 32 MS 36 MS 40 5/8-24 3/4- 20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 1/2-18 1 3/4-18 2-18 2 1/4-18 2 1/2-16 11.11 11.11 11.11 11.11 11.11 11.11 11.11 11.11 12.7 12.7 12.7 12.7 20.7 25.4 28.6 30.2 34.1 37.3 40.4 43.6 50 56.3 62.7 69 3.6 3.6 3.6 3.6 3.6 4.4 4.4 4.4 4.4 4.8 4.8 4.8 102 115 115 115 115 127 127 140 197 197 197 197 Notes : 1. 2. 3. 4. For protective caps with nylon cord, contact factory. Standard - Plating is Cad. For alternative finishes, contact factory. Standard - straight knurling. For diamond knurling on caps, contact factory. Please add 07 suffix for bigger end link. Other Accessories Protective cap for MS series MS-25042 For plugs Has external threads and is used on all plugs where a coupling ring is provided. A D C MAX B MAX E All dimensions are in mm MS Part number Shell size A Thread in inches B C D E MS 25042-10D MS 25042-12D MS 25042-14D MS 25042-16D MS 25042-18D MS 25042-20D MS 25042-22D MS 25042-24D MS 25042-28D MS 25042-32D MS 25042-36D MS 25042-40D MS 10S-1-SL MS 12-12S MS 14-14S MS 16-16S MS 18 MS 20 MS 22 MS 24 MS 28 MS 32 MS 36 MS 40 5/8-24 3/4- 20 7/8-20 1-20 1 1/8-18 1 1/4-18 1 3/8-18 1 1/2-18 1 3/4-18 2-18 2 1/4-18 2 1/2-16 16.67 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 21.4 17.4 20.6 23.7 26.9 30 33 36.4 39.6 46 52 58.7 65 4 4 4 4 4 4.8 4.8 4.8 4.8 5.6 5.6 5.6 102 115 115 115 115 127 127 140 197 197 197 197 31 AMPHENOL MS And 97B Series Other Accessories Protective cap for 97B series 'B' 97B-25042 For Plugs INK MARK A CONN. NO. & BATCH CODE AS PER BOM. All dimensions are in mm 'A' 'B' SHELL MAX. MAX. SIZE 10 SL 21.0 14 S 27.50 16 S 16 33.50 20 37.0 22 40.0 24 43.0 28 49.50 32 56.0 36 62.50 40 73.0 'E' MIN. 90.0 23.50 4.30 30.0 18 'D' + 0.60/-0 'E' + ONE LINK 'A' 'D' 100.0 115.0 4.70 130.0 5.50 190.0 31.50 'B' Protective Cap For 97B Series 97B-25043 'D' INK MARK A CONN. NO. & BATCH CODE AS PER BOM. All dimensions are in mm SHELL SIZE 'A' MAX. 10 SL 23.0 14 S 30.0 16 S 16 'B' + 0.20 'D' + 0.60/-0 16.0 'E' MIN. 90.0 32.50 18 37.0 20 40.50 22 43.50 24 47.0 28 54.0 32 60.50 36 67.0 40 73.0 4.30 100.0 115.0 20.70 5.50 160.0 Note :- Please add 07 suffix for bigger end link. Applicable for Jam Nut AMPHENOL 32 'E' + ONE LINK 'A' For Receptacle MS And 97B Series Other Accessories Dummy receptacle MS-3105 A B OC E OG D F MAX All dimensions are in mm Part number (see note) A B C 3.05 D Thread in inches 5/8-24 MS-3105-10S 25.4 18.26 MS-3105-12S 27.79 E F G 14.27 3.96 8.20 20.62 3.05 3/4-20 14.27 3.96 11.43 max. MS-3105-12 27.79 20.62 3.05 3/4-20 19.05 3.96 11.43 MS-3105-14S 30.17 23.01 3.05 7/8-20 14.27 3.96 13.36 MS-3105-14 30.17 23.01 3.05 7/8-20 19.05 3.96 13.36 MS-3105-16S 32.54 24.61 3.05 1-20 14.27 3.96 16.41 MS-3105-16 32.54 24.61 3.05 1-20 19.05 3.96 16.41 MS-3105-18 34.92 26.97 3.05 1 1/8-18 19.05 5.16 18.03 MS-3105-20 38.10 29.36 3.05 1 1/4-18 19.05 5.16 23.54 MS-3105-22 41.27 31.75 3.05 1 3/8-18 19.05 5.16 25.93 MS-3105-24 44.45 34.92 3.73 1 1/2-18 20.62 5.16 29.21 MS-3105-28 50.8 39.67 3.73 1 3/4-18 20.62 5.16 34.67 MS-3105-36 63.5 49.22 4.39 2 1/4-16 22.2 9.11 46.56 Note: The dash number also indicates shell size. Special Accessories For special accessories, please contact factory with specifications and drawings. Amphenol has in-house capability to meet and custom build your special accessories requirements for its range of MIL-C5015 MS and 97B series connectors. 33 AMPHENOL MS And 97B Series MS/97B Connector- Accessories Crimp contact Contacts for MS/97B connectors are machined from copper alloys and silver plated for maximum corrosion resistance, with a minimum millivolt drop and a maximum current carrying capacity; the size 16 and 12 socket contacts are of the closed entry design. Gold plated contacts are also available. Part Number For Crimp Contacts only* MS-106433 Pin/ Socket Pin MS-108456 Socket MS-108295 Pin MS-108457 Socket MS-108388 Pin MS-110262 Socket MS-108386 Pin MS-108387 Socket MS-108384 Pin MS-111878 Socket MS-112067 Pin MS-112068 Socket Mating End Size Wire Barrel Size 16 Short 16 16 Long 16 12 12 Allowable Wire size Test Current*** Amps Insertion/Removal Tool 16 18 60 22** 16 18 20 22** 13 10 7.5 5 13 10 7.5 5 12 14 23 17 97B-IR-12 97B-IR-16 97B-IR-16 8 8 8 10** 46 33 97B-IR-8 4 4 4 6** 80 60 97B-IR-4 0 0 0 1 2** 150 125 97B-IR-0 * Solder contacts are not sold as separate items. Part numbers shown here are for crimp contacts only. ** When using wire adapter sleeve shown. *** Contact rating as stated are test ratings only. The connecter may not withstand full rated current through all contacts continuously. Please note that the electrical data given is not an establishment of electrical safety factors. This is left entirely in the designers hands as he can best determine which peak voltage, switching surges, transients, etc. can be expected in a particular circuit. MS/97B Connectors Application tools When proprietary crimp contacts are employed rather than the standard MS approved solder contacts, the following application tools are recommended for use. There is a possibility of additional crimping tools other than those included being available at present or in the future for this specific application. TOOLING CHART Crimping Tool Positioner/ Turret M22520/1-01 * M22520/1-01 * ** ** ** ** ** ** * Use Daniels Turret TH29-1 or Astro Tool Co. Turret 616266 ** For appropriate crimp tool and positioner refer to Pico Crimping Tool Co. Tools used with Arbor Press 11-7364 AMPHENOL 34 MS And 97B Series MS/97B Series Connectors To obtain the specific connector required, write down the connector number from the typical example below. Only inserts shown in the availability chart shown on page 7 can be specified. Connectors are delivered with protective plastic dust covers. Include premating contact designation only if premating contact is required. The second letter in the premating contact designation stands for the actual contact position. B at the end of the connector number indicates telescopic bushing provided. MS - 3 A - 18 - 19 - P - W - PC 100 PC- Premating contact designation Series designation See pages 8 to 18 MS - Threaded version 97B - Bayonet version 3 4 Alternate positions W-X-Y-Z (No suffix - Normal) - Solder - Crimp See insert orientations on page 6. Shell style 100 - Wall mounting receptacle 101 - Cable connecting receptacle 102 - Box mounting receptacle 103 - Back box mounting receptacle without rear end thread 103X - Back box mounting receptacle with rear end thread to accept accessory (Replace X by required connector class) 105A - Plug without accessories, suitable only of straight accessories 106 107R 107T - Straight plug - Jam nut Receptacle Jam nut Receptacle with threads to accept accessories 107A - Plug suitable for right angle back shell to interlock 108 - 90- plug Contact type P - Pin contacts S - Socket contacts Standard - Silver plating Note : Contact factory for gold plating part number. Insert arrangement See pages 7 to 18 Shell size 10S, 10SL, 12S, 12, 14S, 14, 16S, 16, 18, 20, 22, 24, 28, 32, 36. 0 Connector class - Solid backshell. Applicable to straight plug - Environment resisting with grommet seal and strain relief backshell. 3106F style includes a front gasket seal - Environment resisting with grommet R seal, lightweight, shorter overall length PG - Straight PG threaded backshells Supplied with different diameter sizes to suit varying Cable sizes, used for unshielded cable - Backshell for heat shrinkable end shell G SQ - Backshell for shielding & heat Shrinkable end shells EGM - Backshell with metal ferrule for shielded cable PHM - Backshell without metal ferrule for unshielded cable A F Shell finish Standard - Cadmium plating with olive drab chromate finish Alternate finishes 1. Cadmium free zinccobalt plating with olive drab chromate finish-622 2. Cadmium free zinccobalt plating with black finish (624) 3. Electroless Nickel plating(A23) 4. 608:- Black Anodized For details contact factory. For 97B - Connector Modification F 42 - Less grommet & backshell F0/LC - Less contacts 563 - Gold plated contacts T 00 - Metric threads in flange holes 97 BS - Bayonet Version with Steel wear pin (for receptacle connector) RFI - Plug connector with grounding finger HD - Heavy duty coupling ring Note:- Connector 3103 supplied in two types. Connector with rear end thread to accept backshell & without rear end thread. To order 3103 without rear end thread do not add any connector class such as( A,E,F,R...) & hence it is similar to 3102 with Back Box mount For e.g 97B-3103-18-1P-622 Connector without thread 35 AMPHENOL MS And 97B Series Notes : Notice : All information, including illustrations given herein is believed to be accurate at the time of printing. In lieu of design advances, Amphenol reserves the right to change specifications without notice. This publication ACR11 0601 01/10 MS AND 97B Series Connectors supercedes all existing Amphenol literature on MS AND 97 B Series Connectors. AMPHENOL 36 Bangalore Operations Pune Operations MARKETING HEAD QUARTERS Southern Region Northern and Eastern Region 105, Bhosari Industrial Area, Pune - 411 026. Tel.: 91- 020 - 30688303, 30688304 Fax : 91 - 020 - 30688321 Email : vbhavsar@amphenol-in.com sales@amphenol-in.com 4931, 11th Floor, High Point IV 45, Palace Road, Bangalore 560 001. Tel.: 91-80-22281392, 22281002 Fax : 91-80-22253859 Email : kmanoj@amphenol-in.com 1414, 14th Floor, Chiranjiv Tower, 43, Nehru Place, New Delhi - 110 019. Tel. : 91-11-26449177 Telefax : 91-11-26449176 Email : sunily@amphenol-in.com Export Western Region Central Region 105, Bhosari Industrial Area, Pune - 411 026, India. Tel.: 91- 20 - 30688305, 30688353 Fax : 91- 20 - 27129158 Email : svpatil@amphenol-in.com 105, Bhosari Industrial Area, Pune - 411 026. Tel.: 91- 20 - 27119735, 30688334 Fax: 91- 20 - 27120581, 27119735 Email : sunilp@amphenol-in.com 107, 1st Floor, `Am Sri Classic', Sarojinidevi Road, Secunderabad-500 003. Telefax : 91- 40-66332906 Email : pprasad@amphenol-in.com www.amphenol-in.com www.czarcontent.com Our offices in India: