Probing Solutions PP007-WR PP007-WS Passive Probe LEADING FEATURES * Compact probe head * Supports fine pitch SMD probing * Rugged, sharp tip * HF optimized connection accessories * Over 30 accessories * Low input capacitance TECHNICAL SPECIFICATIONS Electrical Characteristics: Attenuation: / 10 Bandwidth: > 500 MHz The PP007 is designed to be an ideal general purpose probe. It features 500 MHz bandwidth, rugged design and a wide assortment of accessories. Input R: 10 M Updated Passive Probe Optimized for HF Applications Input C: 9.5 pF Max. Input Voltage 400 V CAT I (1250 V surge) 300 V CAT II The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day. The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed--important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes. The input capacitance of the probe is very low for a passive probe--to minimize loading of high frequency signals. However, keeping any resonance beyond the passband also requires low inductance in the interconnections. Probes with limited interconnection accessories often force the user to extend the input or ground lead lengths to connect to the circuit--a practice that adds inductance and lowers the resonate frequency. General Characteristics: Ground Sleeve Diameter: 2.5 mm Input Pin Diameter: 0.5 mm Cable Length: 1.3 m * A rigid tip is included Accessories such as the ground spring and innovative ground blade (PK007-013) provide a very low inductance ground interconnect. Copper foil tape, (PK007-014) included with the probe, can be placed on top of an IC and connected to its ground pins to create a convenient ground plane for the probe to connect to. Used with the ground blade, this method provides an ideal ground connection for probing signals with high frequency content. Rugged Probe for Everyday Use Unlike some probes, the PP007 does not trade off physical robustness to obtain excellent high frequency performance. The probe will stand up to the rigors of everyday use. The probe has a working voltage rating of 400VCAT I with transient surges up to 1250 V. Ground Blade Used with Copper Foil For applications which require the flexibility of a longer ground lead without compromising high frequency performance, the optional HF-compensated ground lead (PK007-030) provides a solution. A passive network in the lead itself reduces the loading effect of any resonance. Ease in Probing SMT Circuits In addition to the small probe head size, the PP007 is augmented with several accessories to simplify probing dense surface mounted circuit assemblies. Insulating probe caps with guide fingers (PK007-009, 010, 011, 012) keep the small probe tip centered on the IC lead and prevent it from shorting to adjacent leads. The IC Caps are supplied in a range of sizes designed for IC lead pitches from 0.5 mm through 1.27 mm. EN61010-31-2 Installation category I (CAT I) is for probing circuits which are isolated from the power mains through a power supply transformer--the most common circuits measured with oscilloscopes. The probe also is rated fora CAT II working voltage of 300 V. CAT II circuits are on the primary side of power converters and similar power line connected circuits which are not intended to be permanently connected to building wiring. The probe tip is mounted in a socket, allowing user replacement should it ever break. Ordering the Correct Model The PP007 is supplied in two models, each optimized to give the best performance with a specific family of oscilloscope. The PP007-WR is designed to be used with the WaveRunner 6000 series, while the PP007-WS is designed for the WaveSurfer 400 series oscilloscopes. The physical design of the probes are identical. All of the connection accessories, standard and optional, will fit both models. Sales and Service Throughout the World Corporate Headquarters 700 Chestnut Ridge Road Chestnut Ridge, NY 10977 USA www.lecroy.com LeCroy Sales Offices: China: Beijing Phone (86) 10 8526 1618 Fax (86) 10 8526 1619 France: Les Ulis Phone (33) 1 6918 8320 Fax (33) 1 6907 4042 Germany: Heidelberg Phone (49) 6221 827 00 Fax (49) 6221 834 655 Hong Kong Phone (852) 2834 5630 Fax (852) 2834 9893 Italy: Venice Phone (39) 041 599 7011 Fax (39) 041 456 9542 Japan: Osaka Phone (81) 6 6396 0961 Fax (81) 6 6396 0962 Japan: Tokyo Phone (81) 3 3376 9400 Fax (81) 3 3376 9587 Korea: Seoul Phone (82) 2 3452 0400 Fax (82) 2 3452 0490 Singapore Phone (65) 6442 4880 Fax (65) 6442 7811 Optional accessory kits contain 0.5 mm micro clips for attaching to the smallest IC leads, along with adapter leads to connect to the probe tip. Sweden: Stockholm Phone (46) 8 580 143 45 Fax (46) 8 580 143 45 Switzerland: Geneva Phone (41) 22 719 2228 (North) Phone (41) 22 719 2175 (South) Fax (41) 22 719 2230 Ordering Information Passive Probe for WR6000 Series Oscilloscopes Passive Probe for WS400 Series Oscilloscopes Basic Adapter Kit Advanced Adapter Kit SMD Adapter Kit Micro Clip Kit Instruction Manual Product Code PP007-WR-1 PP007-WS-1 PK701 PK702 PK703 PK704 PP007-OM-E U.K.: Abingdon Phone (44) 1 235 536 973 Fax (44) 1 235 528 796 U.S.A.: Chestnut Ridge Phone (1) 845 578 6020 Fax (1) 845 578 5985 (c) 2004 by LeCroy Corporation. All rights reserved. LeCroy, ActiveDSO, ProBus, SMART Trigger, JitterTrack, WavePro, WaveMaster, and Waverunner are registered trademarks of LeCroy Corporation. Information in this publication supersedes all earlier versions. Specifications subject to change without notice. DSPP007 PDF 8/04