Document Number: 42017 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 16-Feb-07 25
Type 418P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
FEATURES
•Identical performance characteristics to Type
225P pressed polyester capacitors through 600
WVDC ratings
•Wound from PETP polyester film and thin gauge
foil under carefully controlled atmospheric
conditions
•Protected against moisture by a conformal coating of
epoxy
•Specifically designed for printed wiring board applications
•Widely used in computers, instrumentation and
telecommunications equipment
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C, standard; up to
+ 105 °C when WVDC is reduced to 70 % of + 85 °C rating.
To + 125 °C when WVDC is 50 % of + 85 °C rating.
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 100 000 Megohm for C ≤ 0.25 Microfarads
25000 Megohm - Microfarads for C > 0.25 Microfarads
At + 85 °C: 10 000 Megohm for C ≤ 0.15 Microfarads
1500 Megohm - Microfarads for C > 0.15 Microfarads
At + 105 °C: 1500 Megohm for C ≤ 0.17 Microfarads
250 Megohm - Microfarads for C > 0.17 Microfarads
At + 125 °C: 200 Megohm for C ≤ 0.13 Microfarads
25 Megohm - Microfarads for C > 0.13 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency for 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %.
Dielectric Withstanding Voltage:
Capacitors rated below 1000 volts shall withstand a DC
potential of 250 % of rated voltage applied between terminals
for not more than 5 seconds. Capacitance rated 1000 volts
and above shall withstand a DC potential of 200 % of rated
voltage applied between the terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test:
Condition capacitors with no voltage applied for 72 hours at
95 % relative humidity and + 75 °C. Remove capacitors from
humidity chamber, wipe surface dry of moisture and dry in
circulating air for 4 hours. Measure insulation resistance after
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
whichever is less. Minimum product of insulation resistance
and capacitance shall be 5000 Megohm - Microfarads after
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
RoHS
COMPLIANT
DIMENSIONS in inches [millimeters]
Case
Code
L
(Max.)
S
Terminal A and B Terminal D
J 0.70 [17.78] 0.500 [12.700] 0.375 [9.525]
K 0.90 [22.86] 0.688 [17.475] 0.375 [9.525]
L 1.20 [30.48] 0.969 [24.613] 0.719 [18.263]
M 1.60 [40.64] 1.344 [34.138] 1.094 [27.788]
1.250
[31.750]
Min.
0.237
[6.019]
Max.
L
Max.
S
± 0.060 [1.524]
Terminal A
L
Max.
0.237
[6.019]
Max.
Lead
Length
S
± 0.030 [0.762]
Terminal B
L
Max.
0.237
[6.019]
Max.
Lead
Length
0.032 [0.813] Dia.
(No. 20 AWG)
Tinned Copper-Clad Steel
D
Max.
S
± 0.030 [0.762]
Terminal D
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42017
26 Revision: 16-Feb-07
Type 418P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3).
** 60 Hz rms
CAPACITANCE CHANGE
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
16
14
12
!0
8
6
4
2
0
2
4
6
zH0001/EGNAHC ECNATICAPAC %
CAPACITANCE CHANGE ENVELOPE
FOR 96 % CONFIDENCE LEVEL
TEMPERATURE DEG. CENTIGRADE
DISSIPATION FACTOR VS. TEMPERATURE
TYPICAL
zH0001/ NOITAPISSID %
- 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125
- 50 + 100
TEMPERATURE DEG. CENTIGRADE
1.5
1.0
.5
0
STANDARD RATINGS*
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LH
100 VDC/70 VAC**
0.027 418P27391J 0.70 [17.78] 0.35 [8.89]
0.033 418P33391J 0.70 [17.78] 0.35 [8.89]
0.047 418P47391J 0.70 [17.78] 0.35 [8.89]
0.082 418P82391K 0.90 [22.86] 0.40 [10.16]
0.1 418P10491K 0.90 [22.86] 0.40 [10.16]
0.15 418P15491K 0.90 [22.86] 0.45 [11.43]
0.22 418P22491L 1.20 [30.48] 0.45 [11.43]
0.33 418P33491L 1.20 [30.48] 0.50 [12.70]
0.47 418P47491M 1.60 [40.64] 0.50 [12.70]
0.68 418P68491M 1.60 [40.64] 0.60 [15.24]
1.0 418P10591M 1.60 [40.64] 0.70 [17.78]
200 VDC/140 VAC**
0.0056 418P56292J 0.70 [17.78] 0.33 [8.38]
0.0068 418P68292J 0.70 [17.78] 0.33 [8.38]
0.01 418P10392J 0.70 [17.78] 0.33 [8.38]
0.015 418P15392J 0.70 [17.78] 0.33 [8.38]
0.018 418P18392J 0.70 [17.78] 0.33 [8.38]
0.022 418P22392J 0.70 [17.78] 0.33 [8.38]
0.033 418P33392K 0.90 [22.86] 0.38 [9.65]
0.039 418P39392K 0.90 [22.86] 0.38 [9.65]
0.047 418P47392K 0.90 [22.86] 0.38 [9.65]
0.056 418P56392L 1.20 [30.48] 0.38 [9.65]
0.068 418P68392L 1.20 [30.48] 0.38 [9.65]
0.082 418P82392L 1.20 [30.48] 0.40 [10.16]
0.1 418P10492L 1.20 [30.48] 0.40 [10.16]
0.15 418P15492L 1.20 [30.48] 0.45 [11.43]
0.22 418P22492L 1.20 [30.48] 0.50 [12.70]
0.27 418P27492M 1.60 [40.64] 0.47 [11.94]
0.33 418P33492M 1.60 [40.64] 0.47 [11.94]
0.47 418P47492M 1.60 [40.64] 0.55 [13.97]
Type 418P
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead Vishay Sprague
Document Number: 42017 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 16-Feb-07 27
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3).
** 60 Hz rms
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LH
400 VDC/200 VAC**
0.001 418P10294J 0.70 [17.78] 0.30 [7.62]
0.0015 418P15294J 0.70 [17.78] 0.30 [7.62]
0.0022 418P22294J 0.70 [17.78] 0.30 [7.62]
0.0033 418P33294J 0.70 [17.78] 0.30 [7.62]
0.0047 418P47294J 0.70 [17.78] 0.30 [7.62]
0.0068 418P68294J 0.70 [17.78] 0.33 [8.38]
0.0082 418P82294J 0.70 [17.78] 0.35 [8.89]
0.01 418P10394J 0.70 [17.78] 0.35 [8.89]
0.015 418P15394J 0.70 [17.78] 0.38 [9.65]
0.018 418P18394K 0.90 [22.86] 0.38 [9.65]
0.022 418P22394K 0.90 [22.86] 0.38 [9.65]
0.033 418P33394K 0.90 [22.86] 0.40 [10.16]
0.047 418P47394L 1.20 [30.48] 0.40 [10.16]
0.056 418P56394L 1.20 [30.48] 0.45 [11.43]
0.068 418P68394L 1.20 [30.48] 0.45 [11.43]
0.082 418P82394L 1.20 [30.48] 0.52 [13.21]
0.1 418P10494L 1.20 [30.48] 0.52 [13.21]
0.15 418P15494L 1.20 [30.48] 0.57 [14.48]
0.18 418P18494M 1.60 [40.64] 0.60 [15.24]
0.22 418P22494M 1.60 [40.64] 0.60 [15.24]
0.27 418P27494M 1.60 [40.64] 0.65 [16.51]
0.33 418P33494M 1.60 [40.64] 0.65 [16.51]
0.39 418P39494M 1.60 [40.64] 0.72 [18.29]
0.47 418P47494M 1.60 [40.64] 0.80 [20.32]
600 VDC/200 VAC**
0.001 418P10296J 0.70 [17.78] 0.30 [7.62]
0.0012 418P12296J 0.70 [17.78] 0.33 [8.38]
0.0015 418P15296J 0.70 [17.78] 0.33 [8.38]
0.0018 418P18296J 0.70 [17.78] 0.33 [8.38]
0.0022 418P22296J 0.70 [17.78] 0.33 [8.38]
0.0027 418P27296J 0.70 [17.78] 0.35 [8.89]
0.0033 418P33296J 0.70 [17.78] 0.35 [8.89]
0.0039 418P39296J 0.70 [17.78] 0.38 [9.65]
0.0047 418P47296J 0.70 [17.78] 0.38 [9.65]
0.0056 418P56296J 0.70 [17.78] 0.40 [10.16]
0.0068 418P68296J 0.70 [17.78] 0.40 [10.16]
0.0082 418P82296K 0.90 [22.86] 0.40 [10.16]
0.01 418P10396K 0.90 [22.86] 0.40 [10.16]
0.012 418P12396K 0.90 [22.86] 0.40 [10.16]
0.015 418P15396K 0.90 [22.86] 0.40 [10.16]
0.018 418P18396K 0.90 [22.86] 0.45 [11.43]
0.022 418P22396K 0.90 [22.86] 0.45 [11.43]
0.027 418P27396L 1.20 [30.48] 0.45 [11.43]
0.033 418P33396L 1.20 [30.48] 0.45 [11.43]
0.039 418P39396L 1.20 [30.48] 0.55 [13.97]
0.047 418P47396L 1.20 [30.48] 0.55 [13.97]
0.056 418P56396L 1.20 [30.48] 0.60 [15.24]
0.068 418P68396L 1.20 [30.48] 0.60 [15.24]
0.082 418P82396L 1.20 [30.48] 0.65 [16.51]
0.1 418P10496L 1.20 [30.48] 0.65 [16.51]
0.12 418P12496M 1.60 [40.64] 0.70 [17.78]
0.15 418P15496M 1.60 [40.64] 0.70 [17.78]
0.18 418P18496M 1.60 [40.64] 0.80 [20.32]
0.22 418P22496M 1.60 [40.64] 0.80 [20.32]
0.25 418P25496M 1.60 [40.64] 0.80 [20.32]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42017
28 Revision: 16-Feb-07
Type 418P
Vishay Sprague Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
* These standard ratings are available through Sprague® distribution on special order. For complete Part Number, add letter and number for
terminal and lead length in accordance with How to Order (Ex: 418P47492MD3)
** 60 Hz rms
STANDARD RATINGS in inches [millimeters]
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LH
1000 VDC/200 VAC**
0.001 418P102910J 0.70 [17.78] 0.33 [8.38]
0.0015 418P152910J 0.70 [17.78] 0.33 [8.38]
0.0018 418P182910J 0.70 [17.78] 0.35 [8.89]
0.0022 418P222910J 0.70 [17.78] 0.35 [8.89]
0.0033 418P332910K 0.90 [22.86] 0.35 [8.89]
0.0047 418P472910K 0.90 [22.86] 0.40 [10.16]
0.0056 418P562910K 0.90 [22.86] 0.43 [10.92]
0.0068 418P682910K 0.90 [22.86] 0.43 [10.92]
0.0082 418P822910K 0.90 [22.86] 0.48 [12.19]
0.01 418P103910K 0.90 [22.86] 0.48 [12.19]
0.015 418P153910L 1.20 [30.48] 0.48 [12.19]
0.018 418P183910L 1.20 [30.48] 0.58 [14.73]
0.022 418P223910L 1.20 [30.48] 0.58 [14.73]
0.027 418P273910L 1.20 [30.48] 0.65 [16.51]
0.033 418P333910L 1.20 [30.48] 0.65 [16.51]
0.039 418P393910M 1.60 [40.64] 0.65 [16.51]
0.047 418P473910M 1.60 [40.64] 0.65 [16.51]
0.056 418P563910M 1.60 [40.64] 0.75 [19.05]
0.068 418P683910M 1.60 [40.64] 0.75 [19.05]
0.082 418P823910M 1.60 [40.64] 0.85 [21.59]
0.1 418P104910M 1.60 [40.64] 0.85 [21.59]
ORDERING INFORMATION
418P 104 9 1 J, K, L or M D 3 (-XXX)
TYPE CAPACITANCE TOLERANCE DC VOLTAGE
RATING
CASE CODE TERMINAL LEAD LENGTH SPECIAL
CONSTRUCTION
Capacitance is
expressed in
picofarads. The
first two digits are
significant. The
third is the number
of zeros to follow.
Values must
conform to Decade
Rating for the
tolerance
specified.
0 = ± 20 %
9 = ± 10 %
5 = ± 5 %
This is
expressed in
hundred of
volts.
See Dimensional
Configurations
A = Straight Lead
B = Hairpin Crimped
D = Hockey Crimped
1 = 0.187" ± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250" [31.750]
Minimum
A three-digit suffix
may be added by
the factory to
denote special
construction.
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
