Type 418P Vishay Sprague Polyester Capacitors Filmite(R) "E", ORANGE DROP(R), Radial Lead FEATURES * Identical performance characteristics to Type 225P pressed polyester capacitors through 600 WVDC ratings RoHS * Wound from PETP polyester film and thin gauge COMPLIANT foil under carefully controlled atmospheric conditions * Protected against moisture by a conformal coating of epoxy * Specifically designed for printed wiring board applications * Widely used in computers, instrumentation and telecommunications equipment PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 85 C, standard; up to + 105 C when WVDC is reduced to 70 % of + 85 C rating. To + 125 C when WVDC is 50 % of + 85 C rating. Insulation Resistance: After a 2 minute charge at rated voltage or 500 V, whichever is less. At + 25 C: 100 000 Megohm for C 0.25 Microfarads 25000 Megohm - Microfarads for C > 0.25 Microfarads At + 85 C: 10 000 Megohm for C 0.15 Microfarads 1500 Megohm - Microfarads for C > 0.15 Microfarads At + 105 C: 1500 Megohm for C 0.17 Microfarads 250 Megohm - Microfarads for C > 0.17 Microfarads At + 125 C: 200 Megohm for C 0.13 Microfarads 25 Megohm - Microfarads for C > 0.13 Microfarads Capacitance Tolerance and Dissipation Factor: Capacitors shall be measured at a frequency for 1000 Hz at + 25 C or else be referred to measurements made at that frequency and temperature. The maximum dissipation factor shall be 0.75 %. Dielectric Withstanding Voltage: Capacitors rated below 1000 volts shall withstand a DC potential of 250 % of rated voltage applied between terminals for not more than 5 seconds. Capacitance rated 1000 volts and above shall withstand a DC potential of 200 % of rated voltage applied between the terminals for not more than 5 seconds. The test voltage must be applied and discharged through a resistor of 1 ohm per volt. Humidity Test: Condition capacitors with no voltage applied for 72 hours at 95 % relative humidity and + 75 C. Remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure insulation resistance after a 2 minute charge at 25 C and rated voltage or 500 VDC, whichever is less. Minimum product of insulation resistance and capacitance shall be 5000 Megohm - Microfarads after test but need not exceed 10 000 Megohm. Not more than one failure allowed in 12 units tested. DC Life Test: Capacitance are capable of withstanding a 500 hour life test at + 85 C at 150 % of rated working voltage. After test, capacitance shall not have changed by more than 5 % of initial value, insulation resistance shall not have decreased by more than 50 % of the initial limit and dissipation factor shall not have increased to more than 1 %. DIMENSIONS in inches [millimeters] L Max. L Max. 0.237 [6.019] Max. 1.250 [31.750] Min. D Max. 0.237 [6.019] Max. Lead Length S 0.060 [1.524] Terminal A 0.237 [6.019] Max. Lead Length S 0.030 [0.762] S 0.030 [0.762] Terminal B Terminal D Case Code L (Max.) J K L M 0.70 [17.78] 0.90 [22.86] 1.20 [30.48] 1.60 [40.64] Document Number: 42017 Revision: 16-Feb-07 L Max. 0.032 [0.813] Dia. (No. 20 AWG) Tinned Copper-Clad Steel S Terminal A and B 0.500 [12.700] 0.688 [17.475] 0.969 [24.613] 1.344 [34.138] For technical questions, contact: spresale@vishay.com Terminal D 0.375 [9.525] 0.375 [9.525] 0.719 [18.263] 1.094 [27.788] www.vishay.com 25 Type 418P Polyester Capacitors Filmite(R) "E", ORANGE DROP(R), Radial Lead % CAPACITANCE CHANGE/1000Hz CAPACITANCE CHANGE DISSIPATION FACTOR VS. TEMPERATURE 16 14 12 !0 CAPACITANCE CHANGE ENVELOPE 8 FOR 96 % CONFIDENCE LEVEL 6 4 2 0 2 4 6 - 55 - 40 - 25 0 + 25 + 50 + 75 + 85 + 105 + 125 - 50 + 100 1.5 % DISSIPATION /1000Hz Vishay Sprague 1.0 TYPICAL .5 0 - 55 - 40 - 25 - 50 0 + 25 + 50 + 75 + 85 + 105 + 125 + 100 TEMPERATURE DEG. CENTIGRADE TEMPERATURE DEG. CENTIGRADE STANDARD RATINGS* F 10 % TOLERANCE SIZE PART NUMBER L H 100 VDC/70 VAC** 0.027 0.033 0.047 0.082 0.1 0.15 0.22 0.33 0.47 0.68 1.0 418P27391J 418P33391J 418P47391J 418P82391K 418P10491K 418P15491K 418P22491L 418P33491L 418P47491M 418P68491M 418P10591M 0.0056 0.0068 0.01 0.015 0.018 0.022 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.15 0.22 0.27 0.33 0.47 418P56292J 418P68292J 418P10392J 418P15392J 418P18392J 418P22392J 418P33392K 418P39392K 418P47392K 418P56392L 418P68392L 418P82392L 418P10492L 418P15492L 418P22492L 418P27492M 418P33492M 418P47492M 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.90 [22.86] 0.90 [22.86] 0.90 [22.86] 1.20 [30.48] 1.20 [30.48] 1.60 [40.64] 1.60 [40.64] 1.60 [40.64] 200 VDC/140 VAC** 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.90 [22.86] 0.90 [22.86] 0.90 [22.86] 1.20 [30.48] 1.20 [30.48] 1.20 [30.48] 1.20 [30.48] 1.20 [30.48] 1.20 [30.48] 1.60 [40.64] 1.60 [40.64] 1.60 [40.64] 0.35 [8.89] 0.35 [8.89] 0.35 [8.89] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.50 [12.70] 0.50 [12.70] 0.60 [15.24] 0.70 [17.78] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.38 [9.65] 0.38 [9.65] 0.38 [9.65] 0.38 [9.65] 0.38 [9.65] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.50 [12.70] 0.47 [11.94] 0.47 [11.94] 0.55 [13.97] * These standard ratings are available through Sprague(R) distribution on special order. For complete Part Number, add letter and number for terminal and lead length in accordance with How to Order (Ex: 418P47492MD3). ** 60 Hz rms www.vishay.com 26 For technical questions, contact: spresale@vishay.com Document Number: 42017 Revision: 16-Feb-07 Type 418P Polyester Capacitors Filmite(R) "E", ORANGE DROP(R), Radial Lead Vishay Sprague STANDARD RATINGS* in inches [millimeters] F 10 % TOLERANCE SIZE PART NUMBER L 400 VDC/200 VAC** 0.001 418P10294J 0.70 [17.78] 0.0015 418P15294J 0.70 [17.78] 0.0022 418P22294J 0.70 [17.78] 0.0033 418P33294J 0.70 [17.78] 0.0047 418P47294J 0.70 [17.78] 0.0068 418P68294J 0.70 [17.78] 0.0082 418P82294J 0.70 [17.78] 0.01 418P10394J 0.70 [17.78] 0.015 418P15394J 0.70 [17.78] 0.018 418P18394K 0.90 [22.86] 0.022 418P22394K 0.90 [22.86] 0.033 418P33394K 0.90 [22.86] 0.047 418P47394L 1.20 [30.48] 0.056 418P56394L 1.20 [30.48] 0.068 418P68394L 1.20 [30.48] 0.082 418P82394L 1.20 [30.48] 0.1 418P10494L 1.20 [30.48] 0.15 418P15494L 1.20 [30.48] 0.18 418P18494M 1.60 [40.64] 0.22 418P22494M 1.60 [40.64] 0.27 418P27494M 1.60 [40.64] 0.33 418P33494M 1.60 [40.64] 0.39 418P39494M 1.60 [40.64] 0.47 418P47494M 1.60 [40.64] 600 VDC/200 VAC** 0.001 418P10296J 0.70 [17.78] 0.0012 418P12296J 0.70 [17.78] 0.0015 418P15296J 0.70 [17.78] 0.0018 418P18296J 0.70 [17.78] 0.0022 418P22296J 0.70 [17.78] 0.0027 418P27296J 0.70 [17.78] 0.0033 418P33296J 0.70 [17.78] 0.0039 418P39296J 0.70 [17.78] 0.0047 418P47296J 0.70 [17.78] 0.0056 418P56296J 0.70 [17.78] 0.0068 418P68296J 0.70 [17.78] 0.0082 418P82296K 0.90 [22.86] 0.01 418P10396K 0.90 [22.86] 0.012 418P12396K 0.90 [22.86] 0.015 418P15396K 0.90 [22.86] 0.018 418P18396K 0.90 [22.86] 0.022 418P22396K 0.90 [22.86] 0.027 418P27396L 1.20 [30.48] 0.033 418P33396L 1.20 [30.48] 0.039 418P39396L 1.20 [30.48] 0.047 418P47396L 1.20 [30.48] 0.056 418P56396L 1.20 [30.48] 0.068 418P68396L 1.20 [30.48] 0.082 418P82396L 1.20 [30.48] 0.1 418P10496L 1.20 [30.48] 0.12 418P12496M 1.60 [40.64] 0.15 418P15496M 1.60 [40.64] 0.18 418P18496M 1.60 [40.64] 0.22 418P22496M 1.60 [40.64] 0.25 418P25496M 1.60 [40.64] * These standard ratings are available through Sprague(R) distribution on special order. For complete Part Number, terminal and lead length in accordance with How to Order (Ex: 418P47492MD3). ** 60 Hz rms Document Number: 42017 Revision: 16-Feb-07 For technical questions, contact: spresale@vishay.com H 0.30 [7.62] 0.30 [7.62] 0.30 [7.62] 0.30 [7.62] 0.30 [7.62] 0.33 [8.38] 0.35 [8.89] 0.35 [8.89] 0.38 [9.65] 0.38 [9.65] 0.38 [9.65] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.52 [13.21] 0.52 [13.21] 0.57 [14.48] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.72 [18.29] 0.80 [20.32] 0.30 [7.62] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.33 [8.38] 0.35 [8.89] 0.35 [8.89] 0.38 [9.65] 0.38 [9.65] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.80 [20.32] add letter and number for www.vishay.com 27 Type 418P Vishay Sprague Polyester Capacitors Filmite(R) "E", ORANGE DROP(R), Radial Lead STANDARD RATINGS in inches [millimeters] F 10 % TOLERANCE SIZE PART NUMBER L H 0.001 418P102910J 1000 VDC/200 VAC** 0.70 [17.78] 0.0015 418P152910J 0.70 [17.78] 0.33 [8.38] 0.0018 418P182910J 0.70 [17.78] 0.35 [8.89] 0.0022 418P222910J 0.70 [17.78] 0.35 [8.89] 0.0033 418P332910K 0.90 [22.86] 0.35 [8.89] 0.0047 418P472910K 0.90 [22.86] 0.40 [10.16] 0.0056 418P562910K 0.90 [22.86] 0.43 [10.92] 0.0068 418P682910K 0.90 [22.86] 0.43 [10.92] 0.0082 418P822910K 0.90 [22.86] 0.48 [12.19] 0.01 418P103910K 0.90 [22.86] 0.48 [12.19] 0.015 418P153910L 1.20 [30.48] 0.48 [12.19] 0.018 418P183910L 1.20 [30.48] 0.58 [14.73] 0.022 418P223910L 1.20 [30.48] 0.58 [14.73] 0.027 418P273910L 1.20 [30.48] 0.65 [16.51] 0.033 418P333910L 1.20 [30.48] 0.65 [16.51] 0.039 418P393910M 1.60 [40.64] 0.65 [16.51] 0.047 418P473910M 1.60 [40.64] 0.65 [16.51] 0.056 418P563910M 1.60 [40.64] 0.75 [19.05] 0.068 418P683910M 1.60 [40.64] 0.75 [19.05] 0.082 418P823910M 1.60 [40.64] 0.85 [21.59] 0.1 418P104910M 1.60 [40.64] 0.85 [21.59] 0.33 [8.38] Sprague(R) * These standard ratings are available through distribution on special order. For complete Part Number, add letter and number for terminal and lead length in accordance with How to Order (Ex: 418P47492MD3) ** 60 Hz rms ORDERING INFORMATION 418P TYPE 104 CAPACITANCE Capacitance is expressed in picofarads. The first two digits are significant. The third is the number of zeros to follow. Values must conform to Decade Rating for the tolerance specified. www.vishay.com 28 9 1 TOLERANCE DC VOLTAGE RATING 0 = 20 % 9 = 10 % 5=5% This is expressed in hundred of volts. J, K, L or M CASE CODE See Dimensional Configurations D TERMINAL 3 LEAD LENGTH 1 = 0.187" 0.030" A = Straight Lead [4.750 0.762] B = Hairpin Crimped D = Hockey Crimped 2 = 0.250" 0.030" [6.350 0.762] 3 = 1.250" [31.750] Minimum For technical questions, contact: spresale@vishay.com (-XXX) SPECIAL CONSTRUCTION A three-digit suffix may be added by the factory to denote special construction. Document Number: 42017 Revision: 16-Feb-07 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000