PIC16F785/HV785 PIC16F785/HV785 Memory Programming Specification This document includes the programming specifications for the following devices: 1.1 * PIC16F785 * PIC16HV785 * PIC16F785-ICD The PIC16HV785 requires one power supply for VDD (4.5V) and one for VPP (12V). VDD is lower for the PIC16HV785 to avoid possible contention between the shunt regulator and an unrestricted supply current. 1.0 The PIC16F785 requires one power supply for VDD (5.0V) and one for VPP (12V). PROGRAMMING THE PIC16F785/HV785 1.2 TABLE 1-1: to Program/Verify Mode The Program/Verify mode for the PIC16F785/HV785 allows programming of user program memory, data memory, user ID locations and the Configuration Word register. The PIC16F785/HV785 is programmed using a serial method. The Serial mode will allow the device to be programmed while in the user's system. This allows for increased design flexibility. This programming specification applies PIC16F785/HV785 devices in all packages. Hardware Requirements the PIN DESCRIPTIONS IN PROGRAM/VERIFY MODE: PIC16F785/HV785 During Programming Pin Name Function Pin Type RA0 ICSPDAT I/O RA1 ICSPCLK I Pin Description Data Input/Output - Schmitt Trigger input Clock Input - Schmitt Trigger input Program/Verify mode P(1) VDD VDD P Power Supply VSS VSS P Ground RA3/MCLR Program Mode Select Legend: I = Input, I/O = Input/Output, P = Power Note 1: In the PIC16F785/HV785, the programming high voltage is internally generated. To activate the Program/ Verify mode, high voltage needs to be applied to MCLR input. Since the MCLR is used for a level source, MCLR does not draw significant current. 2009 Microchip Technology Inc. DS41237D-page 1 PIC16F785/HV785 FIGURE 1-1: 20-PIN DIAGRAM FOR PIC16F785/HV785 PDIP, SOIC, SSOP 1 20 VSS RA5/T1CKI/OSC1/CLKIN RA4/AN3/T1G/OSC2/CLKOUT 2 19 3 4 18 17 16 RA0/AN0/C1IN+/ICSPDAT RA1/AN1/C12IN0-/VREF/ICSPCLK RA3/MCLR/VPP RC5/CCP1 RC4/C2OUT/PH2 RC3/AN7/C12IN3-/OP1 RC6/AN8/OP1RC7/AN9/OP1+ RB7/SYNC FIGURE 1-2: 5 6 7 8 9 10 PIC16F785/HV785 VDD 15 14 13 12 11 RA2/AN2/T0CKI/INT/C1OUT RC0/AN4/C2IN+ RC1/AN5/C12IN1-/PH1 RC2/AN6/C12IN2-/OP2 RB4/AN10/OP2RB5/AN11/OP2+ RB6 20-PIN DIAGRAM FOR PIC16F785/HV785 18 17 16 1 2 15 14 3 PIC16F785/HV78513 4 12 5 11 RA1/AN1/C12IN0-/VREF/ICSPCLK RA2/AN2/T0CKI/INT/C1OUT RC0/AN4/C2IN+ RC1/AN5/C12IN1-/PH1 RC2/AN6/C12IN2-/OP2 RC7/AN9/OP1+ RB7/SYNC RB6 RB5/AN11/OP2+ RB4/AN10/OP2- 6 7 8 9 10 RA3/MCLR/VPP RC5/CCP1 RC4/C2OUT/PH2 RC3/AN7/C12IN3-/OP1 RC6/AN8/OP1- 20 19 RA4/AN3/TIG/OSC2/CLKOUT RA5/T1CKI/OSC1/CLKIN VDD GND RA0/AN0/C1IN+/ICSPDAT QFN DS41237D-page 2 2009 Microchip Technology Inc. PIC16F785/HV785 FIGURE 1-3: ICD PINOUT 28-Pin PDIP In-Circuit Debug Device 1 28 2 3 27 26 4 5 25 24 6 7 8 9 10 11 PIC16F785-ICD SHNTREG ICDMCLR/VPP VDD RA5 RA4 RA3 RC5 RC4 RC3 RC6 RC7 RB7 ICD NC 23 22 21 20 19 18 12 17 13 14 16 15 2009 Microchip Technology Inc. ICDCLK ICDDATA Vss RA0 RA1 RA2 RC0 RC1 RC2 RB4 RB5 RB6 NC NC DS41237D-page 3 PIC16F785/HV785 2.0 MEMORY DESCRIPTION 2.1 Program Memory Map The user memory space extends from 0x0000 to 0x1FFF, with addresses 0x0000-0x07FF implemented. In Program/Verify mode, the program memory space extends from 0x0000 to 0x3FFF, with the first half (0x0000-0x1FFF) being user program memory and the second half (0x2000-0x3FFF) being configuration memory. The PC will increment from 0x0000-0x1FFF and wrap to 0x0000. If the PC starts at 0x2000 it will increment to 0x3FFF and wrap around to 0x2000 (not to 0x0000). Once in configuration memory, the highest bit of the PC stays a `1', thus always pointing to the configuration memory. The only way to point to user program memory is to reset the part and re-enter Program/Verify mode as described in Section 3.0 "Program/Verify Mode". In the configuration memory space, 0x2000-0x203F are physically implemented. However, only locations 0x2000-0x2003 and 0x2007-0x2009 are available. The other locations are reserved. 2.2 User ID Locations 2.3 Calibration Words The 8 MHz Internal Oscillator (INTOSC), the Power-on Reset (POR), the Brown-out Reset (BOR) modules and band gap voltage reference are factory calibrated. These values are stored in Calibration Words at addresses 0x2008 and 0x2009. The Calibration Word locations are written at the time of manufacturing and are not erased when a Bulk Erase is performed. See Section 3.1.5.10 "Bulk Erase Program Memory" for more information on the various erase sequences. However, it is possible to inadvertently write to these locations. The device may not function properly or may operate outside of specifications if the Calibration Word locations do not contain the correct value. Therefore, it is recommended that the Calibration Words be read prior to any programming procedure and verified after programming is complete. See Figure 3-21 for a flowchart of the recommended verification procedure. The device should not be used if the verification of the Calibration Word values fail after the device is programmed. The 0x3FFF value is a special case, it is a valid calibration value but, it is also the erased state of the register. A user may store identification information (user ID) in four designated locations. The user ID locations are mapped in [0x2000-0x2003]. It is recommended that the user use only the seven Least Significant bits (LSb) of each user ID location. The user ID locations read out normally, even after code protection is enabled. It is recommended that user ID locations are written as `11 1111 1bbb bbbb' where `bbb bbbb' is user ID information. The 14 bits may be programmed, but only the 7 LSbs are displayed by MPLAB(R) IDE. The 1111's are "don't care" bits and are not read by MPLAB(R) IDE. DS41237D-page 4 2009 Microchip Technology Inc. PIC16F785/HV785 FIGURE 2-1: PROGRAM MEMORY MAPPING 2 K Implemented 07FF 2000 User ID Location 2001 User ID Location 2002 User ID Location 2003 User ID Location 2004 Reserved 2005 Reserved 2006 Device ID 2007 Configuration Word Program Memory Maps to 0-7FF 1FFF 2000 Implemented 2040 Unimplemented 2008 Calibration Word 2009 Calibration Word 2009-203F Configuration Memory Reserved 3FFF 2009 Microchip Technology Inc. DS41237D-page 5 PIC16F785/HV785 3.0 PROGRAM/VERIFY MODE Two methods are available to enter Program/Verify mode. The `VPP-first' method is entered by holding ICSPDAT and ICSPCLK low while raising MCLR pin from VIL to VIHH (high voltage), then applying VDD and data. This method can be used for any Configuration Word selection and must be used if the INTOSC and internal MCLR options are selected (FOSC<2:0> = 100 or 101 and MCLRE = 0). The VPP-first entry prevents the device from executing code prior to entering Program/Verify mode. See the timing diagram in Figure 3-1. To prevent the device from executing code while exiting Program/Verify mode, the `VPP-last' must also be used if the INTOSC and internal MCLR options are selected. See the timing diagram in Figure 3-3. The second entry method, `VDD-first', is entered by applying VDD, holding ICSPDAT and ICSPCLK low, then raising MCLR pin from VIL to VIHH (high voltage), followed by data. This method can be used for any Configuration Word selection except when INTOSC options are selected and internal MCLR (FOSC<2:0> = 100 or 101 and MCLRE = 0). This technique is useful when programming the device when VDD is already applied, for it is not necessary to disconnect VDD to enter or exit Program/Verify mode. See the timing diagram in Figure 3-2. Once in this mode, the program memory, data memory, and configuration memory can be accessed and programmed in serial fashion. ICSPDAT and ICSPCLK are Schmitt Trigger inputs in this mode. The sequence that enters the device into the Programming/Verify mode momentarily places all other logic into the Reset state (the MCLR pin was initially at VIL). Therefore, all I/O's are in the Reset state (highimpedance inputs) and the Program Counter (PC) is cleared. FIGURE 3-1: VPP-FIRST PROGRAM/ VERIFY MODE ENTRY TPPDP THLD0 VPP VDD ICSPDAT ICSPCLK Note: This method of entry is valid, regardless of Configuration Word selected. FIGURE 3-2: VDD-FIRST PROGRAM/ VERIFY MODE ENTRY THLD0 TPPDP VPP VDD ICSPDAT ICSPCLK Note: This method of entry is not valid if INTOSC and internal MCLR are selected. FIGURE 3-3: To prevent a device configured with INTOSC and internal MCLR from executing after exiting Program/ Verify mode, VDD needs to power-down before VPP. See Figure 3-3 for the timing. VPP-LAST PROGRAM/ VERIFY MODE EXIT THLD0 VPP VDD ICSPDAT ICSPCLK Note: DS41237D-page 6 This method must be used if INTOSC and internal MCLR are selected. 2009 Microchip Technology Inc. PIC16F785/HV785 3.1 Program/Erase Algorithms The PIC16F785/HV785 program memory may be written in two ways. The fastest method writes four words at a time. However, one-word writes are also supported for backward compatibility with previous 8pin and 14-pin Flash devices. The four-word algorithm is used to program the program memory and the user ID locations only. The one-word algorithm can write any available memory location (i.e., program memory, configuration memory and data memory). After writing the array, the PC may be reset and the entire array read back to verify the write. It is not possible to verify immediately following the write because the PC can only increment, not decrement. A device Reset will clear the PC and set the address to `0'. The Increment Address command will increment the PC. The Load Configuration command will set the PC to 0x2000. The available commands are shown in Table 3-1. 3.1.1 This algorithm writes four sequential addresses in program memory. The four addresses must point to a four-word block with addresses modulo 4 of 0, 1, 2 and 3. For example, programming address 4 through 7 can be programmed together. Programming addresses 2 through 5 will create an unexpected result. The sequence for programming four words of program memory at a time is as follows: 2. 3. 4. 5. 6. 7. 8. 9. Load a word at the current program memory address using Load Data for Program Memory command. Issue an Increment Address command. Load a word at the current program memory address using Load Data for Program Memory command. Repeat Steps 2 and 3, two more times. Issue a Begin Programming command, either internally or externally timed. Wait TPROG1 (internally timed) or TPROG2 (externally timed). Issue an End Programming command if externally timed. Issue an Increment Address command. Repeat steps 1 through 8 as required to write program memory. ONE-WORD PROGRAMMING The program memory may also be written one-word at a time to allow compatibility with other 8-pin and 14-pin Flash PIC(R) devices. Configuration memory (>0x2003) and data memory must be written one-word (or byte) at a time with the exception of the user ID locations. Note: The four write latches must be reset after programming the user ID (0x20000x2003) or Configuration Word (0x2007). See Section 3.1.3 "Resetting Write Latches". The sequence for programming one-word of program memory at a time is as follows: 1. 2. 3. FOUR-WORD PROGRAMMING Only the program memory can be written using this algorithm. Data and configuration memory (>0x2003) must use the one-word programming algorithm (Section 3.1.2 "One-Word Programming"). 1. 3.1.2 4. 5. 6. Load a word at the current program memory address using Load Data for Program Memory command. Issue a Begin Programming command either internally or externally timed. Wait TPROG1 (internally timed) or TPROG2 (externally timed). Issue an End Programming command if externally timed. Issue an Increment Address command. Repeat this sequence as required to write program, data or configuration memory. See Figure 3-16 for more information. 3.1.3 RESETTING WRITE LATCHES The user ID (0x2000-0x2003) and Configuration Word (0x2007) are mapped into the configuration memory but do not physically reside in it. As a result, the write latches are not reset when programming these locations and must be reset by the programmer. This can be done in two ways, either loading all four latches with `1's or by exiting Program/Verify mode. The sequence for manually resetting the write latches is as follows: 1. 2. 3. Load a word using Load Data for Program Memory command with a data word of all `1's. Issue an Increment Address command. Repeat this sequence three times to all four write latches to 1's (Reset state). See Figure 3-17 for more information. 2009 Microchip Technology Inc. DS41237D-page 7 PIC16F785/HV785 3.1.4 ERASE ALGORITHMS 3.1.5 The PIC16F785/HV785 will erase different memory locations depending on the Program Counter (PC), CP and CPD values, and which erase command is executed. The following sequences can be used to erase noted memory locations. In each sequence, the data memory will be erased if the CPD bit in the Configuration Word is programmed (clear). The ICSPCLK pin is used as a clock input and the ICSPDAT pin is used for entering command bits and data input/output during serial operation. To input a command, ICSPCLK is cycled six times. Each command bit is latched on the falling edge of the clock with the LSb of the command being input first. The data input onto the ICSPDAT pin is required to have a minimum setup and hold time (see Table 6-1), with respect to the falling edge of the clock. Commands that have data associated with them (read and load) are specified to have a minimum delay of 1 s between the command and the data. After this delay, the clock pin is cycled 16 times with the first cycle being a Start bit and the last cycle being a Stop bit. To erase the program memory and Configuration Word (0x2007), the following sequence must be performed. Note: 1. 2. The Calibration Words (0x2008-0x2009) and user ID (0x2000-0x2003) will not be erased. Do a Bulk Erase Program Memory command. Wait TERA to complete erase. During a read operation, the LSb will be transmitted onto ICSPDAT pin on the rising edge of the second cycle. For a load operation, the LSb will be latched on the falling edge of the second cycle. A minimum 1 s delay is also specified between consecutive commands, except for the End Programming command, which requires a 100 s TDIS. To erase the user ID (0x2000-0x2003), Configuration Word (0x2007) and program memory use the following sequence. Note that the Calibration Words (0x20080x2009) will not be erased. 1. 2. 3. Perform a Load Configuration command with dummy data to point the Program Counter (PC) to 0x2000. Perform a Bulk Erase Program Memory command. Wait TERA to complete erase. Note: SERIAL PROGRAM/VERIFY OPERATION All commands and data words are transmitted LSb first. Data is transmitted on the rising edge and latched on the falling edge of the ICSPCLK. To allow for decoding of commands and reversal of data pin configuration, a time separation of at least 1 s is required between a command and a data word. See Table 3-2. The commands that are available are described in Table 3-1. TABLE 3-1: COMMAND MAPPING FOR PIC16F785/HV785 Command Mapping (MSb ... LSb) Data Load Configuration x x 0 0 0 0 Load Data for Program Memory x x 0 0 1 0 0, data (14), 0 Load Data for Data Memory x x 0 0 1 1 0, data (8), zero (6), 0 Read Data from Program Memory x x 0 1 0 0 0, data (14), 0 0, data (8), zero (6), 0 Read Data from Data Memory x x 0 1 0 1 Increment Address x x 0 1 1 0 Begin Programming (internally timed) x 0 1 0 0 0 Begin Programming (externally timed)(1) x 1 1 0 0 0 End Programming x 0 1 0 1 0 Bulk Erase Program Memory (internally timed)(2) x x 1 0 0 1 x x 1 0 1 1 x 1 0 0 0 1 Bulk Erase Data Memory (internally timed)(2) Row Erase Program Memory (internally timed)(2) Note 1: 2: 0, ones data (14), 0 Externally timed Data EE programming is a program-only command. No erase cycle is performed. VDD must be at least 4.0V for this command. DS41237D-page 8 2009 Microchip Technology Inc. PIC16F785/HV785 3.1.5.1 Load Configuration After the 6-bit command is input, ICSPCLK pin is cycled an additional 16 times for the Start bit, 14 bits of data and a Stop bit (see Figure 3-4). The Load Configuration command is used to access the Configuration Word (0x2007) and the user ID (0x2000-0x2003). This command sets the Program Counter (PC) to address 0x2000. The data field must be loaded with all ones. After the configuration memory is entered, the only way to get back to the program memory is to exit the Program/Verify mode by taking MCLR low (VIL). After receiving this command, the Configuration Word is accessed by performing an Increment Address command 7 times to point the PC to the Configuration Word. Data can be loaded using the Load Data for Program Memory command then be programmed using a Begin Programming command, either internally or externally timed. FIGURE 3-4: LOAD CONFIGURATION COMMAND TDLY2 1 2 3 4 5 0 0 x 1 6 2 3 4 5 15 16 ICSPCLK 0 ICSPDAT 00 MSb stp_bit LSb strt_bit x TSET1 TDLY1 THLD1 3.1.5.2 Load Data for Program Memory After receiving this command, the device will load in a 14-bit `data word' when 16 cycles are applied, as described previously. A timing diagram for the Load Data for Program Memory command is shown in Figure 3-5. FIGURE 3-5: LOAD DATA FOR PROGRAM MEMORY COMMAND TDLY2 1 2 3 4 0 0 5 1 6 2 3 4 5 15 16 ICSPCLK ICSPDAT 0 1 TSET1 THLD1 2009 Microchip Technology Inc. x x TDLY1 strt_bit MSb stp_bit LSb TSET1 THLD1 DS41237D-page 9 PIC16F785/HV785 3.1.5.3 Load Data for Data Memory After receiving this command, the device will load in a 14-bit `data word' when 16 cycles are applied. However, the data memory is only 8 bits wide and thus, only the first 8 bits of data after the Start bit will be programmed into the data memory. It is still necessary to cycle the clock the full 16 cycles in order to allow the internal circuitry to reset properly. The data memory contains 256 bytes. FIGURE 3-6: LOAD DATA FOR DATA MEMORY COMMAND TDLY2 1 2 3 4 5 1 6 2 3 4 5 15 16 ICSPCLK ICSPDAT 1 1 0 0 x x stp_bit strt_bit LSb MSb on 9th falling edge TDLY1 3.1.5.4 Read Data from Program Memory After receiving this command, the device will transmit data bits out of the program memory (user or configuration) currently accessed, starting with the second rising edge of the clock input. The data pin will go into Output mode on the second rising clock edge, and it will revert to Input mode (high-impedance) after the 16th rising edge. If the program memory is code-protected (CP = 0), the data is read as `0's. FIGURE 3-7: READ DATA FROM PROGRAM MEMORY COMMAND TDLY2 1 2 3 4 5 6 1 2 3 4 5 15 16 ICSPCLK TDLY3 ICSPDAT 0 0 1 0 TSET1 x x strt_bit MSb LSb stp_bit TDLY1 THLD1 input DS41237D-page 10 output input 2009 Microchip Technology Inc. PIC16F785/HV785 3.1.5.5 Read Data from Data Memory After receiving this command, the device will transmit data bits out of the data memory starting with the second rising edge of the clock input. The ICSPDAT pin will go into Output mode on the second rising edge, and it will revert to Input mode (high-impedance) after the 16th rising edge. As previously stated, the data memory is 8 bits wide, and therefore, only the first 8 bits that are output are actual data. If the data memory is codeprotected, the data is read as all `0's. A timing diagram of this command is shown in Figure 3-8. FIGURE 3-8: READ DATA FROM DATA MEMORY COMMAND TDLY2 1 2 3 4 5 6 1 2 3 4 5 15 16 ICSPCLK TDLY3 ICSPDAT 1 0 1 0 x x strt_bit stp_bit LSb MSb on 9th falling edge TSET1 TDLY1 THLD1 input 3.1.5.6 input output Increment Address The PC is incremented when this command is received. A timing diagram of this command is shown in Figure 3-9. It is not possible to decrement the address counter. To reset this counter, the user should exit and re-enter Program/Verify mode. FIGURE 3-9: INCREMENT ADDRESS COMMAND (PROGRAM/VERIFY) TDLY2 1 2 3 4 5 1 6 Next Command 2 ICSPCLK ICSPDAT 0 1 1 0 TSET1 THLD1 2009 Microchip Technology Inc. TDLY1 DS41237D-page 11 PIC16F785/HV785 3.1.5.7 Begin Programming (Internally Timed) A Load command must be given before every Begin Programming command. Programming of the appropriate memory (user program memory, configuration memory or data memory) will begin after this command is received and decoded. An internal timing mechanism executes a write. The user must allow for program cycle time for programming to complete. No End Programming command is required. The addressed programming. FIGURE 3-10: location is not erased before BEGIN PROGRAMMING COMMAND (INTERNALLY TIMED) TPROG1 1 2 3 0 0 0 4 5 Next Command 2 1 6 ICSPCLK ICSPDAT 1 0 x TSET1 THLD1 3.1.5.8 Begin Programming (Externally Timed) A Load command must be given before every Begin Programming command. Programming of the appropriate memory (program memory, configuration or data memory) will begin after this command is received and decoded. Programming requires (TPROG2) time and is terminated using an End Programming command. The addressed programming. FIGURE 3-11: location is not erased before BEGIN PROGRAMMING (EXTERNALLY TIMED) TPROG2 1 2 3 0 0 0 4 5 6 1 x End Programming command 1 2 ICSPCLK ICSPDAT 1 TSET1 THLD1 DS41237D-page 12 2009 Microchip Technology Inc. PIC16F785/HV785 3.1.5.9 End Programming The End Programming command is executed when terminating external timing or programming. The End Programming command requires a 100 s TDIS. FIGURE 3-12: END PROGRAMMING (SERIAL PROGRAM/VERIFY) Next Command 1 2 3 4 0 1 0 5 1 6 2 ICSPCLK ICSPDAT 1 0 x TDIS TSET1 THLD1 3.1.5.10 Bulk Erase Program Memory After this command is performed, the entire program memory and Configuration Word (0x2007) are erased. Data memory will also be erased if the CPD bit in the Configuration Word is programmed (clear). See Section 3.1.4 "Erase Algorithms" for erase sequences. Note: All Bulk Erase operations must take place between 4.5V and 5.5V VDD for PIC16F785, 2.0V to 5.5V VDD for PIC16F785-ICD and 4.5V to 4.9V for PIC16HV785. FIGURE 3-13: BULK ERASE PROGRAM MEMORY COMMAND TERA 1 2 3 0 0 4 5 6 1 Next Command 2 ICSPCLK ICSPDAT 1 1 x x TSET1 THLD1 2009 Microchip Technology Inc. DS41237D-page 13 PIC16F785/HV785 TABLE 3-2: BULK ERASE RESULTS PC = Configuration Memory Space Programming Memory Space (Program Memory) Configuration Word User ID Calibration Word E E U U Configuration Word or Program Memory Space First User ID Location E E E U Either Calibration Word E E E E Legend: E = Erased, U = Unchanged. 3.1.5.11 Bulk Erase Data Memory To perform an erase of the data memory, the following sequence must be performed. 1. 2. Perform a Bulk Erase Data Memory command. Wait TERA to complete Bulk Erase. Data memory won't erase if code-protected (CPD = 0). If CPD = 0, a Bulk Erase program memory must be used. Note: All Bulk Erase operations must take place between 4.5V and 5.5V VDD for PIC16F785, 2.0V to 5.5V VDD for PIC16F785-ICD and 4.5V to 4.9V for PIC16HV785. FIGURE 3-14: BULK ERASE DATA MEMORY COMMAND TERA 1 2 3 4 5 1 6 Next Command 2 ICSPCLK ICSPDAT 1 1 0 1 x x TSET1 THLD1 DS41237D-page 14 2009 Microchip Technology Inc. PIC16F785/HV785 3.1.5.12 Row Erase Program Memory This command erases the 16-word row of program memory pointed to by PC<11:4>. If the program memory array is protected (CP = 0) or the PC points to configuration memory (>0x2000), the command is ignored. To perform a Row Erase Program Memory, the following sequence must be performed. 1. 2. Execute a Row Erase Program Memory command. Wait TERA to complete a row erase. Note: All row erase operations must take place between 4.5V and 5.5V VDD for PIC16F785, 2.0V to 5.5V VDD for PIC16F785-ICD and 4.5V to 4.9V for PIC16HV785. FIGURE 3-15: ROW ERASE PROGRAM MEMORY COMMAND TERA 1 2 3 4 5 1 0 0 0 1 1 6 Next Command 2 ICSPCLK ICSPDAT 2009 Microchip Technology Inc. x DS41237D-page 15 PIC16F785/HV785 FIGURE 3-16: ONE-WORD PROGRAMMING FLOWCHART Start Read and Store Calibration Memory Values (Figure 3-21) Device(1) Bulk Erase (Figure 3-20) Program Cycle Load Data For Program Memory One-word Program Cycle Read Data From Program Memory Data Correct? No Report Programming Failure Begin Programming Command (internally timed) Begin Programming Command (externally timed) Wait TPROG1 Wait TPROG2 Yes Increment Address Command No All Locations Done? End Programming Yes Exit Program Verify Mode Wait TDIS Re-enter Program Verify Mode Program Data Memory (Figure 3-19) Program User ID/Config. bits (Figure 3-18) Read and Verify Calibration Memory Values (Figure 3-21) Done DS41237D-page 16 Note 1: This step is optional if device has already been erased or has not been previously programmed. 2009 Microchip Technology Inc. PIC16F785/HV785 FIGURE 3-17: FOUR-WORD PROGRAMMING FLOWCHART Program Cycle Start Read and Store Calibration Memory Values (Figure 3-21) Bulk Erase Device(1) (Figure 3-20) Load Data For Program Memory Increment Address Command Load Data For Program Memory Four-word Program Cycle Increment Address Command Increment Address Command No All Locations Done? Yes Load Data For Program Memory Exit Program Verify Mode Re-enter Program Verify Mode Program Data Memory (Figure 3-19) Increment Address Command Load Data For Program Memory Begin Programming Command (internally timed) Begin Programming Command (externally timed) Wait TPROG1 Wait TPROG2 Program User ID/Config. bits (Figure 3-18) Read and Verify Calibration Memory Values (Figure 3-21) End Programming Done Wait TDIS Note 1: This step is optional if device is erased or not previously programmed. 2009 Microchip Technology Inc. DS41237D-page 17 PIC16F785/HV785 FIGURE 3-18: PROGRAM FLOWCHART - PIC16F785/HV785 CONFIGURATION MEMORY Start Program Cycle Load Configuration Data Load Data For Program Memory One-word Program Cycle (User ID) Read Data From Program Memory Command Data Correct? No Begin Programming Command (internally timed) Begin Programming Command (externally timed) Wait TPROG1 Wait TPROG2 Report Programming Failure End Programming Yes Increment Address Command No Address = 0x2004? Wait TDIS Yes Increment Address Command Increment Address Command Increment Address Command One-word Program Cycle (Config. bits) Read Data From Program Memory Command Data Correct? Yes Done DS41237D-page 18 No Report Programming Failure Note: Ensure that a device Bulk Erase has been performed or that the device is blank prior to programming the configuration memory. 2009 Microchip Technology Inc. PIC16F785/HV785 FIGURE 3-19: PROGRAM FLOWCHART - PIC16F785/HV785 DATA MEMORY Start Program Cycle Program Cycle Load Data For Data Memory Read Data From Program Memory Command Data Correct? Yes Increment Address Command No No Report Programming Failure Begin Programming Command (internally timed) Begin Programming Command (externally timed) Wait TPROG1 (Data Memory) 5-6 ms Wait TPROG2 End Programming All Locations Done? Yes Wait TDIS Done 2009 Microchip Technology Inc. DS41237D-page 19 PIC16F785/HV785 FIGURE 3-20: PROGRAM FLOWCHART - ERASE FLASH DEVICE Start Read and Store Calibration Memory Values (Figure 3-21) Load Configuration Bulk Erase Program Memory Bulk Erase Data Memory Read and Verify Calibration Memory Values (Figure 3-21) Done DS41237D-page 20 2009 Microchip Technology Inc. PIC16F785/HV785 FIGURE 3-21: CALIBRATION WORD VERIFICATION FLOWCHART Start Load Configuration Increment Address Command Address = 0x2008? No Yes Read and Store Calibration Word 1 Calibration Word 1 is Valid?(1,2) No Fail Yes Increment Address Command Read and Store Calibration Word 2 Calibration Word 2 is Valid?(1,2) No Fail Yes Done Note 1: 2: This step is not required for the Read and Store Calibration Memory Values procedure. The device should not be used if verification of the Calibration Word locations fails. This information should be reported to the user through the user interface of the device programmer. 2009 Microchip Technology Inc. DS41237D-page 21 PIC16F785/HV785 4.0 CONFIGURATION WORD The PIC16F785/HV785 has several Configuration bits. These bits can be programmed (reads `0') or left unchanged (reads `1') to select various device configurations. REGISTER 4-1: CONFIG: CONFIGURATION WORD (ADDRESS: 2007h) U-1 U-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 - - FCMEN(5) IESO BOREN1(1) BOREN0(1) CPD(2,3) bit 13 bit 7 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 CP(2) MCLRE(4) PWRTE WDTE(5) FOSC2 FOSC1 FOSC0 bit 6 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' -n = Value at POR `1' = Bit is set `0' = Bit is cleared bit 13-12 Unimplemented: Read as `1' bit 11 FCMEN: Fail-Safe Clock Monitor Enabled bit(5) 1 = Fail-Safe Clock Monitor is enabled 0 = Fail-Safe Clock Monitor is disabled bit 10 IESO: Internal External Switchover bit 1 = Internal External Switchover mode is enabled 0 = Internal External Switchover mode is disabled bit 9-8 BOREN<1:0>: Brown-out Reset Selection bits(1) 11 = BOR enabled 10 = BOR enabled during operation and disabled in Sleep 01 = BOR controlled by SBOREN bit (PCON<4>) 00 = BOR disabled bit 7 CPD: Data Code Protection bit(2,3) 1 = Data memory code protection is disabled 0 = Data memory code protection is enabled bit 6 CP: Code Protection bit(2) 1 = Program memory code protection is disabled 0 = Program memory code protection is enabled bit 5 MCLRE: RA3/MCLR pin function select bit(4) 1 = RA3/MCLR pin function is MCLR 0 = RA3/MCLR pin function is digital input, MCLR internally tied to VDD bit 4 PWRTE: Power-up Timer Enable bit 1 = PWRT disabled 0 = PWRT enabled bit 3 WDTE: Watchdog Timer Enable bit(5) 1 = WDT enabled 0 = WDT disabled and can be enabled by SWDTEN bit (WDTCON<0>) DS41237D-page 22 x = Bit is unknown 2009 Microchip Technology Inc. PIC16F785/HV785 REGISTER 4-1: bit 2-0 Note 1: 2: 3: 4: 5: 4.1 CONFIG: CONFIGURATION WORD (ADDRESS: 2007h) (CONTINUED) FOSC<2:0>: Oscillator Selection bits 111 = RC oscillator: CLKOUT function on RA4/AN3/T1G/OSC2/CLKOUT pin, RC on RA5/T1CKI/OSC1/CLKIN 110 = RCIO oscillator: I/O function on RA4/AN3/T1G/OSC2/CLKOUT pin, RC on RA5/T1CKI/OSC1/CLKIN 101 = INTOSC oscillator: CLKOUT function on RA4/AN3/T1G/OSC2/CLKOUT pin, I/O function on RA5/T1CKI/OSC1/CLKIN 100 = INTOSCIO oscillator: I/O function on RA4/AN3/T1G/OSC2/CLKOUT pin, I/O function on RA5/T1CKI/OSC1/CLKIN 011 = EC: I/O function on RA4/AN3/T1G/OSC2/CLKOUT pin, CLKIN on RA5/T1CKI/OSC1/CLKIN 010 = HS oscillator: High-speed crystal/resonator on RA4/AN3/T1G/OSC2/CLKOUT and RA5/T1CKI/OSC1/ CLKIN(5) 001 = XT oscillator: Crystal/resonator on RA4/AN3/T1G/OSC2/CLKOUT and RA5/T1CKI/OSC1/CLKIN(5) 000 = LP oscillator: Low-power crystal on RA4/AN3/T1G/OSC2/CLKOUT and RA5/T1CKI/OSC1/CLKIN(5) Enabling Brown-out Reset does not automatically enable Power-up Timer. Program memory Bulk Erase must be performed to turn off code protection. The entire data EEPROM will be erased when the code protection is turned off. When MCLR is asserted in INTOSC or RC mode, the internal clock oscillator is disabled. If the HS, XT, or LP oscillator fails In Fail-Safe mode the Watchdog time-out can occur only once after which it will be disabled until the oscillator is restored.. Device ID Word The device ID word for the PIC16F785/HV785 is located at 2006h. This location cannot be erased. TABLE 4-1: DEVICE ID VALUES Device ID Values Device Dev Rev PIC16HV785 01 0010 001 x xxxx PIC16F785 01 0010 000 x xxxx 2009 Microchip Technology Inc. DS41237D-page 23 PIC16F785/HV785 5.0 CODE PROTECTION For the PIC16F785/HV785, once the CP bit is programmed to `0', all program memory locations read all `0's. The user ID locations and the Configuration Word read out in an unprotected fashion. Further programming is disabled for the entire program memory. Data memory is protected with its own code-protect bit (CPD). When enabled, the data memory can still be programmed and read using the EECON1 register. The user ID locations and the Configuration Word can be programmed regardless of the state of the CP and CPD bits. 5.1 Disabling Code Protection It is recommended to use the procedure in Figure 3-20 to disable code protection of the device. This sequence will erase the program memory, data memory, Configuration Word (0x2007) and user ID locations (0x20000x2003). The Calibration Words (0x2008-0x2009) will not be erased. Note: 5.2 To ensure system security, if CPD bit = 0, Bulk Erase Program Memory command will also erase data memory. Embedding Configuration Word and User ID Information in the Hex File To allow portability of code, the programmer is required to read the Configuration Word and user ID locations from the hex file when loading the hex file. If Configuration Word information was not present in the hex file, a simple warning message may be issued. Similarly, while saving a hex file, Configuration Word and user ID information must be included. An option to not include this information may be provided. 5.3 5.3.1 Checksum Computation CHECKSUM Checksum is calculated by reading the contents of the PIC16F785/HV785 memory locations and adding up the opcodes up to the maximum user addressable location (e.g., 0x7FF for the PIC16F785/HV785). Any Carry bits exceeding 16 bits are neglected. Finally, the Configuration Word (appropriately masked) is added to the checksum. Checksum computation for the PIC16F785/HV785 devices is shown in Table 5-1. The checksum is calculated by summing the following: * The contents of all program memory locations * The Configuration Word, appropriately masked * Masked user ID locations (when applicable) The 16 LSbs of this sum is the checksum. The following table describes how to calculate the checksum for each device. Note that the checksum calculation differs depending on the code-protect setting. Since the program memory locations read out `0's when code-protected, the table describes how to manipulate the actual program memory values to simulate values that would be read from a protected device. When calculating a checksum by reading a device, the entire program memory can simply be read and summed. The Configuration Word and user ID locations can always be read regardless of code-protect setting. Note: Some older devices have an additional value added in the checksum. This is to maintain compatibility with older device programmer checksums. Specifically for the PIC16F785/HV785, the data memory should also be embedded in the hex file (see Section 5.3.2 "Embedding Data Memory Contents in Hex File"). Microchip Technology Incorporated feels strongly that this feature is important for the benefit of the end customer. DS41237D-page 24 2009 Microchip Technology Inc. PIC16F785/HV785 TABLE 5-1: CHECKSUM COMPUTATIONS Device PIC16F785/HV785 Code-Protect Checksum* OFF SUM[0x0000:0x7FF] + CFGW & 0FFF ALL CFGW & 0x0FFF + SUM_ID Blank Value 0x25E6 at 0 and Max. Address 07FF D3CD 173E(1) E30C(1) Legend: CFGW = Configuration Word. Example calculations assume Configuration Word is erased (all 1's). SUM[a:b] = [Sum of locations a to b inclusive] SUM_ID = User ID locations masked by 0xF then made into a 16-bit value with ID0 as the Most Significant nibble. For example, ID0 = 0x1, ID1 = 0x2, ID3 = 0x3, ID4 = 0x4, then SUM_ID = 0x1234. The 4 LSbs of the unprotected checksum is used for the example calculations. * = Checksum - [Sum of all the individual expressions] MODULO [0xFFFF] + = Addition & = Bitwise AND Note 1: Checksum shown assumes that both the data and program memory are code-protected and that SUM_ID contains the unprotected checksum. 5.3.2 EMBEDDING DATA MEMORY CONTENTS IN HEX FILE The programmer should be able to read data memory information from a hex file and conversely (as an option), write data memory contents to a hex file along with program memory information and Configuration Word (0x2007) and user ID (0x2000-0x2003) information. The 256 data memory locations are logically mapped starting at address 0x2100. The format for data memory storage is one data byte per address location, LSb aligned. 2009 Microchip Technology Inc. DS41237D-page 25 PIC16F785/HV785 6.0 PROGRAM/VERIFY MODE ELECTRICAL CHARACTERISTICS TABLE 6-1: AC/DC CHARACTERISTICS TIMING REQUIREMENTS FOR PROGRAM/VERIFY MODE Standard Operating Conditions (unless otherwise stated) Operating Temperature -40C TA +85C Operating Voltage 4.5V VDD 5.5V AC/DC CHARACTERISTICS Sym. Characteristics Min. Typ. Max. Units Conditions/Comments General VDD VDD level for read/write operations, program and data memory 2.0 2.0 -- -- 5.5 4.9 V V PIC16F785/PIC16F785-ICD PS200 VDD level for Bulk Erase operations, program and data memory 2.0 4.5 4.5 -- -- -- 5.5 5.5 4.9(1) V V V PIC16F785-ICD PIC16F785 PIC16HV785 VIHH High voltage on MCLR for Program/ Verify mode entry 10 -- 12 V TVHHR MCLR rise time (VSS to VHH) for Program/Verify mode entry -- -- 1.0 s TPPDP Hold time after VPP changes 5 -- -- s VIH1 (ICSPCLK, ICSPDAT) input high level 0.8 VDD -- -- V VIL1 (ICSPCLK, ICSPDAT) input low level 0.2 VDD -- -- V TSET0 ICSPCLK, ICSPDAT setup time before MCLR (Program/Verify mode selection pattern setup time) 100 -- -- ns THLD0 Hold time after VDD changes 5 -- -- s TSET1 Data in setup time before clock 100 -- -- ns THLD1 Data in hold time after clock 100 -- -- ns TDLY1 Data input not driven to next clock input (delay required between command/data or command/ command) 1.0 -- -- s TDLY2 Delay between clock to clock of next command or data 1.0 -- -- s TDLY3 Clock to data out valid (during a Read Data command) -- 80 ns TERA Erase cycle time -- 5 6 ms TPROG1 Programming cycle time (internally timed) 2 5 -- 2.5 6 ms TPROG2 Programming cycle time (externally timed) 2 -- 2.5 ms TDIS Time delay from program to compare (HV discharge time) 100 -- -- s Serial Program/Verify Note 1: Program memory Data memory 10C TA +40C Program memory Exceeding the maximum voltage may cause the shunt regulator to draw excessive current and damage the device. DS41237D-page 26 2009 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2009 Microchip Technology Inc. DS41237D-page 27 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS41237D-page 28 2009 Microchip Technology Inc.