HSMP-386D PIN Diode Diversity Switch Data Sheet Description Features The HSMP-386D is a low cost and high linearity diversity switch designed to operate from 50MHz to 6GHz. HSMP-386D is built with unique 4 PIN diode configuration, and it is housed in a industrial standard low cost miniature SOT-143 package, which will allow board space saving for space constraint application. * Unique configurations in Surface Mount SOT-143 HSMP-386D is equipped with -0.35dB IL and -25.40dB ISO @ 900MHz. On the other hand, HSMP-386D is also featuring with 56.83dBm IIP3 and 47.41dBm IP1dB performance @ 900MHz. HSMP-386D is suitable for wireless application that required low distortion diversity switch, such as dect phone, wireless LAN and WiMAX. - Increase Flexibility - Save Board Space - Reduce Cost * Switching - Low Distortion Switching - Low Capacitance * Low Failure In Time (FIT) Rate [1] * Specifications at 900MHz; IF=10mA (Typ.) - Low IL, 0.35dB - High ISO, 25.40dB Pin Connections and Package Marking, SOT-143 3 4 1 2 L7? Notes: L7 = Device Code ? = Month code indicates the month of manufacture - High power handling, IP1dB, 47.41dBm - High Linearity, IIP3, 56.83dBm Table 1. Absolute Maximum Rating [1] Tc = +25C Symbol Parameter Units Absolute Max. IF Forward Current (1s Pulse) Amp 1 PIV Peak Inverse Voltage V 50 TJ Junction temperature C 150 TSTG Storage Temperature C -65 to 150 JC Thermal Resistance [2] C/W 500 Notes: 1. Operation in excess of anyone of these conditions may result in permanent damage to the device. 2. TC = 25C, TC where is defined to be the temperature at the package pins where contacts is made to the circuit board. Table 2. Electrical Specifications, Tc = +25C, each diode Symbol Parameter and Test Condition Units Min. Typ Max. VBR Breakdown Voltage @ IR = 10A V - 55 - VF Forward Voltage @ IF = 30mA V - 0.88 - VF Forward Voltage @ IF =100mA V - 0.96 1.15 RS Typical Series Resistance @ Freq = 100MHz & IF =1mA Ohm - 17.0 - RS Typical Series Resistance @ Freq = 100MHz & IF =10mA Ohm - 2.6 - RS Typical Series Resistance @ Freq = 100MHz & IF =100mA Ohm - 1.2 - CT Typical Total Capacitance @ Freq = 1MHz & VR = 0V pF - 0.35 0.55 T Carrier Lifetime @ IF = 50mA & IR =250mA ns - 500 - Trr Reverse Recovery Time @ VR =10V, IF = 20mA & 90% Recovery ns - 75 - Table 3. Performance Table at Nominal Operating Conditions, Tc = +25C, IF = 10mA, each diode IIP3 [1, 4] Input 3rd order Intercept Point @ freq = 0.9GHz dBm - 56.83 - IIP3 [2, 4] Input 3rd order Intercept Point @ freq = 1.9GHz dBm - 57.93 - IIP3 [3, 4] Input 3rd order Intercept Point @ freq = 2.4GHz dBm - 59.26 - IP1dB [4] Input 1dB Compressed Power @ freq = 0.9GHz dBm - 47.41 - IP1dB [4] Input 1dB Compressed Power @ freq = 1.9GHz dBm - 48.11 - IP1dB [4] Input 1dB Compressed Power @ freq = 2.4GHz dBm - 48.45 - Notes: 1. 0.9 GHz OIP3 Test Condition : F1 = 0.9 GHz & F2 = 0.905 GHz, Pin =30 dBm 2. 1.9 GHz OIP3 Test Condition : F1 = 1.9 GHz & F2 = 1.905 GHz, Pin =30 dBm 3. 2.4 GHz OIP3 Test Condition : F1 = 2.4 GHz & F2 = 2.405 GHz, Pin =30 dBm 4. Measurement obtained using the demoboard described in Figure 7 & 8. 2 HSMP-386D Typical Performance, Tc = +25C, each diode 1000 25C 125C -50C 10 RESISTANCE (OHMS) IF - FORWARD CURRENT (mA) 100 1 100 10 0.1 0.01 0 0.2 0.4 0.6 0.8 VF - FORWARD VOLTAGE (mA) 1 1 0.01 1.2 Figure 1. Forward Current vs. Forward Voltage 0.1 1 BIAS CURRENT (mA) RETURN LOSS (dB) -10 0.25 -20 -30 -40 0.20 IF=5mA IF=10mA -50 0 2 4 6 8 10 12 14 VR - REVERSE VOLTAGE (V) 16 18 -1 -10 ISOLATION (dB) INSERTION LOSS (dB) 0 -2 -3 IF=5mA IF=10mA 0 1 2 0 1 2 3 4 Frequency (GHz) Figure 5. Insertion Loss vs. Frequency (Pin = 0dBm) 6 -20 -30 -40 IF=5mA IF=10mA -50 3 4 Frequency (GHz) 5 Figure 4. Return Loss vs. Frequency (Pin = 0dBm) 0 -4 3 -60 20 Figure 3. Total Capacitance vs. Reverse Voltage -5 100 0 1MHz 1GHz 0.30 0.15 10 Figure 2. Typical RF Resistance vs. Forward Bias Current 0.35 TOTAL CAPACITANCE (pF) 85C 25C -55C 5 6 -60 0 1 2 3 4 Frequency (GHz) Figure 6. Isolation vs. Frequency (Pin = 0dBm) 5 6 Truth Table APLAC Model Parameters for PIN Diode CTR1 (V) CTR2 (V) Low Loss paths Parameter Units PIN Diode VF 0 RF4-RF3 RF1-RF2 RMAX K 5 1.42 E-9 VF RF3-RF1 RF2-RF4 IS A 0 RF3 N RF4 Bias Tee Bias Tee CTR2 CTR1 VF VF CTR1 1.99 TT ns 500 C pF 0.20 A 0.0276 K 0.9018 RMIN 1.10 L nH 2 CTR2 VF VF Bias Tee Bias Tee RF1 RF2 Figure 7. A diagram showing the application circuit for Diversity Switch using HSMP-386D. This set-up is applicable for measurement shown in Figure 4 - 6. 30.0 Diversity Switch RF 3 RF 4 42.0 RO 4350 DK 3.48 RF 1 H 10 mil RF 2 W 0.56mm G 0.44mm Avago Technologies Figure 8. Evaluation Board for Diversity Switch 4 Package Outline, SOT-143 e2 e1 XXX E E1 L B e C D DIMENSIONS (mm) A A1 Notes: XXX-package marking Drawings are not to scale SYMBOL A A1 B B1 C D E1 e e1 e2 E L MIN. 0.79 0.013 0.36 0.76 0.086 2.80 1.20 0.89 1.78 0.45 2.10 0.45 MAX. 1.097 0.10 0.54 0.92 0.152 3.06 1.40 1.02 2.01 0.60 2.65 0.69 Part Number Ordering Information Part Number No. of Devices Container HSMP-386D-BLK 100 Bulk, per Antistatic bag HSMP-386D-TR1 3000 Tape & Reel, per 7" Reel HSMP-386D-TR2 10000 Tape & Reel, per 13" Reel Tape and Reeling conforms to Electronic Industries RS-481, "Taping of Surface Mounted Components for Automated Placement". 5 For lead-free option, the part number will have the character "G" at the end, eg. -TR2G for a 10K pc lead-free reel. Recommended PCB Pad Layout for AVAGO's SOT-143 Products 0.112 2.85 0.079 2 0.033 0.85 0.075 1.9 0.041 0.108 1.05 2.75 0.071 1.8 0.033 0.85 0.047 0.12 0.03 0.8 0.033 0.85 Dimensions in inches mm Device Orientation REEL TOP VIEW END VIEW 4 mm CARRIER TAPE USER FEED DIRECTION COVER TAPE 6 8 mm ABC ABC ABC Note: "AB" represents package marking code. "C" represents date code. ABC Tape Dimensions and Product Orientation P P2 D E P0 F W D1 t1 9 MAX Ko 9 MAX B0 A0 DESCRIPTION LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER SYMBOL A0 B0 K0 P D1 SIZE (mm) 3.19 0.10 2.80 0.10 1031 0.10 4.00 0.10 1.00 0.25 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 0.10 4.00 0.10 1.75 0.10 SIZE (INCHES) 0.126 0.004 0.110 0.004 0.052 0.004 0.157 0.004 0.039 0.010 0.059 + 0.004 0.157 0.004 0.069 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 + 0.30 - 0.10 0.254 0.013 0.315 + 0.012 - 0.004 0.0100 0.0005 DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) CAVITY TO PERFORATION (LENGTH DIRECTION) F 3.50 0.05 0.138 0.002 P2 2.00 0.05 0.079 0.002 CAVITY For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright (c) 2005-2009 Avago Technologies. All rights reserved. AV02-1689EN - January 13, 2009