PHOTOCOUPLER PS2715-1 HIGH CTR, AC INPUT 4-PIN SOP PHOTOCOUPLER -NEPOC Series- DESCRIPTION The PS2715-1 is an optically coupled isolator containing GaAs light emitting diodes and an NPN silicon phototransistor in a plastic SOP for high density applications. The package is an SOP (Small Outline Package) type for high density mounting applications. FEATURES * AC input response PIN CONNECTION (Top View) * High current transfer ratio (CTR = 200% TYP. @ IF = 1 mA) * High isolation voltage (BV = 3 750 Vr.m.s.) 4 3 * Small and thin package (4-pin SOP) * Ordering number of tape product: PS2715-1-F3, F4 * Pb-Free product 1 * Safety standards * UL approved: File No. E72422 * DIN EN60747-5-2 (VDE0884 Part2) approved (Option) APPLICATIONS * Programmable logic controllers * Modem/FAX Document No. PN10247EJ02V0DS (2nd edition) Date Published April 2005 CP(K) The mark shows major revised points. 2 1. Anode, Cathode 2. Cathode, Anode 3. Emitter 4. Collector PS2715-1 PACKAGE DIMENSIONS (UNIT: mm) 40.5 0.10.1 2.10.2 0.15 +0.10 -0.05 7.00.3 4.4 2.54 0.4 0.50.3 +0.10 -0.05 0.25 M MARKING EXAMPLE No. 1 pin Mark Trade Mark Type Number Assembly Lot 2715 N003 *1 N 0 03 Week Assembled Year Assembled (Last 1 Digit) CTR Rank Code *1 Bar : Pb-Free Remark "PS" and "-1" are omitted from original type number. 2 Data Sheet PN10247EJ02V0DS PS2715-1 ORDERING INFORMATION Part Number Order Number Solder Plating Safety Standard Packing Style Specification Approval PS2715-1 PS2715-1 Solder Magazine case 100 pcs Standard products PS2715-1-F3 PS2715-1-F3 contains lead Embossed Tape 3 500 pcs/reel (UL approved) PS2715-1-F4 PS2715-1-F4 PS2715-1-V PS2715-1-V Magazine case 100 pcs DIN EN60747-5-2 PS2715-1-V-F3 PS2715-1-V-F3 Embossed Tape 3 500 pcs/reel (VDE0884 Part2) PS2715-1-V-F4 PS2715-1-V-F4 PS2715-1 PS2715-1-A PS2715-1-F3 PS2715-1-F3-A PS2715-1-F4 PS2715-1-F4-A PS2715-1-V Application Part *1 Number PS2715-1 Approved (Option) Pb-Free Magazine case 100 pcs Standard products Embossed Tape 3 500 pcs/reel (UL approved) PS2715-1-V-A Magazine case 100 pcs DIN EN60747-5-2 PS2715-1-V-F3 PS2715-1-V-F3-A Embossed Tape 3 500 pcs/reel (VDE0884 Part2) PS2715-1-V-F4 PS2715-1-V-F4-A Approved (Option) *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (Unless otherwise specified, TA = 25C) Parameter Symbol Ratings Unit IF 50 mA PD/C 0.8 mW/C PD 80 mW IFP 0.5 A Collector to Emitter Voltage VCEO 40 V Emitter to Collector Voltage VECO 5 V IC 40 mA PC/C 1.5 mW/C PC 150 mW BV 3 750 Vr.m.s. Operating Ambient Temperature TA -55 to +100 C Storage Temperature Tstg -55 to +150 C Diode Forward Current (DC) Power Dissipation Derating Power Dissipation Peak Forward Current Transistor *1 Collector Current Power Dissipation Derating Power Dissipation Isolation Voltage *2 *1 PW = 100 s, Duty Cycle = 1% *2 AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-2 shorted together, 3-4 shorted together. Data Sheet PN10247EJ02V0DS 3 PS2715-1 ELECTRICAL CHARACTERISTICS (TA = 25C) Parameter Diode Transistor Symbol Conditions Forward Voltage VF IF = 5 mA Terminal Capacitance Ct V = 0 V, f = 1 MHz Collector to Emitter Dark ICEO IF = 0 mA, VCE = 40 V CTR IF = 1 mA, VCE = 5 V MIN. TYP. MAX. Unit 1.15 1.4 V 60 pF 100 nA 400 % 0.3 V Current Coupled Current Transfer Ratio 100 200 (IC/IF) Collector Saturation Voltage VCE (sat) IF = 1 mA, IC = 0.2 mA Isolation Resistance RI-O VI-O = 1 kVDC Isolation Capacitance CI-O V = 0 V, f = 1 MHz Rise Time *1 tr *1 Fall Time VCC = 5 V, IC = 2 mA, RL = 100 tf Pulse Input VCC PW = 100 s Duty cycle = 1/10 IF In monitor 4 11 0.4 pF 4 s 5 *1 Test circuit for switching time VOUT 50 10 RL = 100 Data Sheet PN10247EJ02V0DS PS2715-1 TYPICAL CHARACTERISTICS (Unless otherwise specified, TA = 25C) DIODE POWER DISSIPATION vs. AMBIENT TEMPERATURE TRANSISTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Transistor Power Dissipation PC (mW) 80 60 40 20 50 25 0 Forward Current IF (mA) 150 100 50 25 75 100 Ambient Temperature TA (C) FORWARD CURRENT vs. FORWARD VOLTAGE COLLECTOR TO EMITTER DARK CURRENT vs. AMBIENT TEMPERATURE 10 000 TA = +100C +60C +25C 1 0C -25C -50C 0.1 0.01 0.0 0.5 1.0 1.5 2.0 1 000 VCE = 40 V 20 V 10 V 100 10 1 -25 0 25 50 75 100 Forward Voltage VF (V) Ambient Temperature TA (C) COLLECTOR CURRENT vs. COLLECTOR TO EMITTER VOLTAGE COLLECTOR CURRENT vs. COLLECTOR SATURATION VOLTAGE 25 100 10 mA 5 mA 2 mA IF = 10 mA 20 Collector Current IC (mA) Collector Current IC (mA) 50 Ambient Temperature TA (C) 100 10 200 0 100 75 Collector to Emitter Dark Current ICEO (nA) Diode Power Dissipation PD (mW) 100 5 mA 15 10 2 mA 5 1 mA 0.5 mA 0 2 4 6 8 10 10 1 mA 1 0.1 0.0 Collector to Emitter Voltage VCE (V) IF = 0.5mA 0.2 0.4 0.6 0.8 1.0 Collector Saturation Voltage VCE(sat) (V) Remark The graphs indicate nominal characteristics. Data Sheet PN10247EJ02V0DS 5 PS2715-1 CURRENT TRANSFER RATIO vs. FORWARD CURRENT 1.6 500 1.4 1.2 1.0 0.8 0.6 0.4 Normalized to 1.0 at TA = 25C, IF = 1 mA, VCE = 5 V 0.2 0.0 -50 0 -25 25 50 75 VCE = 5 V, n=3 400 300 200 100 0 0.01 100 0.1 1 100 10 Ambient Temperature TA (C) Forward Current IF (mA) SWITCHING TIME vs. LOAD RESISTANCE SWITCHING TIME vs. LOAD RESISTANCE 100 1 000 IC = 2 mA, VCC = 5 V, CTR = 200% tf IF = 1 mA, VCC = 5 V, CTR = 200% Switching Time t (s) Switching Time t ( s) Current Transfer Ratio CTR (%) Normalized Current Transfer Ratio CTR NORMALIZED CURRENT TRANSFER RATIO vs. AMBIENT TEMPERATURE 10 tf tr td 1 100 ts tr 10 td 1 ts 0.1 10 100 0.1 100 10 k 1k 1k 10 k 100 k Load Resistance RL (k) Load Resistance RL (k) LONG TERM CTR DEGRADATION FREQUENCY RESPONSE 1.2 IF = 1 mA 1.0 -5 CTR (Relative Value) Normalized Gain Gv 0 100 RL = 1 k -10 300 -15 1 100 10 1 000 Frequency f (kHz) Remark The graphs indicate nominal characteristics. 6 TA = 25C 0.6 TA = 60C 0.4 0.2 -20 -25 0.1 0.8 Data Sheet PN10247EJ02V0DS 0 10 102 103 104 Time (Hr) 105 106 PS2715-1 TAPING SPECIFICATIONS (in millimeters) 1.550.1 2.9 MAX. 7.40.1 5.50.05 1.5+0.1 -0 12.00.2 2.00.05 4.00.1 1.750.1 Outline and Dimensions (Tape) 2.40.1 4.60.1 0.3 8.00.1 Tape Direction PS2715-1-F4 PS2715-1-F3 Outline and Dimensions (Reel) 21.00.8 13.00.2 R 1.0 1001.0 2.00.5 13.00.2 3302.0 2.00.5 13.51.0 17.51.0 11.9 to 15.4 Outer edge of flange Packing: 3 500 pcs/reel Data Sheet PN10247EJ02V0DS 7 PS2715-1 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature 260C or below (package surface temperature) * Time of peak reflow temperature 10 seconds or less * Time of temperature higher than 220C 60 seconds or less * Time to preheat temperature from 120 to 180C 12030 s * Number of reflows Three * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Package Surface Temperature T (C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating) Time (s) (2) Wave soldering * Temperature 260C or below (molten solder temperature) * Time 10 seconds or less * Preheating conditions 120C or below (package surface temperature) * Number of times One (Allowed to be dipped in solder including plastic mold portion.) * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron * Peak temperature (lead part temperature) 350C or below * Time (each pins) 3 seconds or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100C. 8 Data Sheet PN10247EJ02V0DS PS2715-1 (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Data Sheet PN10247EJ02V0DS 9 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.