Product Specification Industrial Temperature Range 10Gb/s 850nm Multimode Datacom XFP Optical Transceiver FTLX8512D3BTL PRODUCT FEATURES Hot-pluggable XFP footprint Supports 8.5Gb/s and 9.95 through 10.5 Gb/s bit rates* Power dissipation <1.5W RoHS-6 compliant (lead-free) Temperature range -40C to +85C Single power supply: 3.3V Maximum link length of 300m 850nm heated VCSEL laser. Duplex LC connector No Reference Clock required Built-in digital diagnostic functions Standard bail release mechanism APPLICATIONS 10GBASE-SR/SW 10G Ethernet 1200-Mx-SN-I 10G Fibre Channel 800-Mx-SN-I 8G Fibre Channel G.709 OTN/FEC (OTU1e and OTU2e) Finisar's FTLX8512D3BTL Small Form Factor 10Gb/s (XFP) transceivers are compliant with the current XFP Multi-Source Agreement (MSA) Specification1 now available with Industrial Temperature Range of Operation (-40C to +85C). They comply with 10Gigabit Ethernet 10GBASE-SR/SW per IEEE 802.3ae, 10G Fibre Channel 1200-Mx-SNI, 8G Fibre Channel 800-Mx-SN-I, and OTN/FEC protocols OTU1e and OTU2e upon request. Digital diagnostics functions are available via a 2-wire serial interface, as specified in the XFP MSA. The optical transceiver is compliant per the RoHS Directive 2011/65/EU. See Finisar Application Note AN-2038 for more details3,4. PRODUCT SELECTION FTLX8512D3BTL *Contact Finisar for higher data-rate support Finisar Corporation - August 2015 Rev. E1 Page 1 FTLX8512D3BTL Product Specification I. Pin Descriptions Pin 1 2 3 Logic LVTTL-I 4 LVTTL-O 5 6 7 8 9 10 11 LVTTL-I Symbol GND VEE5 Mod-Desel Interrupt TX_DIS VCC5 GND VCC3 VCC3 SCL SDA 12 LVTTL-I LVTTLI/O LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 15 16 17 18 19 20 21 LVTTL-O LVTTL-I RX_LOS GND GND RDRD+ GND VCC2 P_Down/RST 22 23 24 PECL-I VCC2 GND RefCLK+ 25 PECL-I RefCLK- 26 27 28 29 30 CML-O CML-O CML-I CML-I GND GND TDTD+ GND Name/Description Module Ground Optional -5.2 Power Supply - Not required Module De-select; When held low allows the module to respond to 2-wire serial interface commands Interrupt (bar); Indicates presence of an important condition which can be read over the serial 2-wire interface Transmitter Disable; Transmitter laser source turned off +5 Power Supply - Not required Module Ground +3.3V Power Supply +3.3V Power Supply Serial 2-wire interface clock Serial 2-wire interface data line Ref. 1 Module Absent; Indicates module is not present. Grounded in the module. Module Not Ready; Finisar defines it as a logical OR between RX_LOS and Loss of Lock in TX/RX. Receiver Loss of Signal indicator Module Ground Module Ground Receiver inverted data output Receiver non-inverted data output Module Ground +1.8V Power Supply - Not required Power Down; When high, places the module in the low power stand-by mode and on the falling edge of P_Down initiates a module reset Reset; The falling edge initiates a complete reset of the module including the 2-wire serial interface, equivalent to a power cycle. +1.8V Power Supply - Not required Module Ground Reference Clock non-inverted input, AC coupled on the host board - Not required Reference Clock inverted input, AC coupled on the host board - Not required Module Ground Module Ground Transmitter inverted data input Transmitter non-inverted data input Module Ground 2 2 1 2 2 2 2 1 1 1 1 3 3 1 1 1 Notes: 1. Module circuit ground is isolated from module chassis ground within the module. 2. Open collector; should be pulled up with 4.7k - 10k on host board to a voltage between 3.15V and 3.6V. 3. A Reference Clock input is not required by the FTLX8512D3BTL. If present, it will be ignored. Finisar Corporation - August 2015 Rev. E1 Page 2 FTLX8512D3BTL Product Specification Diagram of Host Board Connector Block Pin Numbers and Name II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Case Operating Temperature Finisar Corporation - August 2015 Symbol Vcc3 TOP Min -0.5 -40 Rev. E1 Typ Max 4.0 +85 Unit V C Ref. Page 3 FTLX8512D3BTL Product Specification III. Electrical Characteristics (TOP = -40 to +85C, VCC3 = 3.13 to 3.45 Volts) Parameter Supply Voltage Supply Current Module total power consumption Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Differential data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc3 Icc3 P Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 3.13 Typ 360 1.2 Max 3.45 435 1.5 100 120 2.0 GND 340 Vcc - 0.5 GND 1000 Vcc GND+ 0.8 10 850 40 40 VccHOST GND+0.5 See Note 7 below Unit V mA W mV V V us mV ps ps V V Ref. 1 1 2 3 4 5 5 6 6 7 Notes: 1. Maximum total power consumption value is specified across the full temperature and voltage range. Typical current at -40C is ~400mA. 2. After internal AC coupling. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 - 80 %. 6. Loss Of Signal is open collector to be pulled up with a 4.7k - 10k resistor to 3.15 - 3.6V. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Per Section 2.7.1. in the XFP MSA Specification1. Finisar Corporation - August 2015 Rev. E1 Page 4 FTLX8512D3BTL Product Specification IV. Optical Characteristics (TOP = -40 to +85C, VCC3 = 3.13 to 3.45 Volts) Parameter Transmitter Optical Modulation Amplitude (OMA) Average Optical Power Optical Wavelength RMS Spectral Width Optical Extinction Ratio Transmitter and Dispersion Penalty Average Launch power of OFF transmitter Tx Jitter Encircled Flux Relative Intensity Noise Receiver Receiver Sensitivity (OMA) @ 10.5Gb/s Stressed Receiver Sensitivity (OMA) @ 10.3Gb/s Maximum Input Power Wavelength Range Receiver Reflectance LOS De-Assert LOS Assert LOS Hysteresis Symbol Min Typ POMA -2.8 -1.5 PAVE rms ER TDP POFF -5.0 840 3.0 850 0.4 5.5 Max -1.0 860 0.45 3.9 -30 Txj <4.5m <19m RIN12OMA Per 802.3ae requirements 30 86 1 % RSENS1 -11.1 RSENS2 -7.5 dBm +0.5 840 860 -12 -14 -30 0.5 Ref. nm dB dB dB dBm dB/Hz dBm PMAX C Rrx LOSD LOSA -128 Unit dBm 2 3 4 dBm nm dB dBm dBm dB Notes: 1. Average power figures are informative only, per IEEE 802.3ae. 2. Measured into Type A1a (50/125 m multimode) fiber per ANSI/TIA/EIA-455-203-2. 3. Measured with worst ER; BER<10-12; 231 - 1 PRBS. 4. Per IEEE 802.3ae. Finisar Corporation - August 2015 Rev. E1 Page 5 FTLX8512D3BTL Product Specification V. General Specifications Parameter Bit Rate Bit Error Ratio Maximum Supported Distances Fiber Type 850nm OFL Bandwidth 160MHz-km OM1 62.5m 200MHz-km 50m 400MHz-km OM2 500MHz-km OM3 2000MHz-km Symbol BR BER Min 8.5 Typ Max 10.5 See Note 2 Units Gb/s Ref. 1 2 26 Lmax 33 m 66 82 Lmax m 300 Notes: 1. 10GBASE-SR/SW, 1200-Mx-SN-I, 800-Mx-SN-I. Contact Finisar for higher data-rate support. 2. 10GBASE-SR/SW, 1200-Mx-SN-I tested with 231 - 1 PRBS @ 10-12 BER. VI. Environmental Specifications This Finisar XFP transceiver model has an operating temperature range from -40C to +85C case temperature. Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -40 -40 Typ Max 85 85 Units C C Ref. 1 Notes: 1. Warm-up time at -40C case temperature is 10 seconds. VII. Regulatory Compliance Finisar XFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Laser Eye Safety Laser Eye Safety Electrical Safety Electrical Safety Agency Standard Certificate Number FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 9210176-77 TUV EN60825 R7201686 TUV EN 60950 R7201686 UL/CSA CLASS 3862.07 CLASS 3862.87 2283290 Copies of the referenced certificates will be available at Finisar Corporation upon request. Finisar Corporation - August 2015 Rev. E1 Page 6 FTLX8512D3BTL Product Specification VIII. Digital Diagnostic Functions As defined by the XFP MSA1, Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: Transceiver temperature Laser bias current Transmitted optical power Received optical power Transceiver supply voltage It also provides a sophisticated system of alarm and warning flags, which may be used to alert end-users when particular operating parameters are outside of a factory-set normal range. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through the 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL pin) is generated by the host. The positive edge clocks data into the XFP transceiver into those segments of its memory map that are not write-protected. The negative edge clocks data from the XFP transceiver. The serial data signal (SDA pin) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. The 2-wire serial interface provides sequential or random access to the 8 bit parameters, addressed from 000h to the maximum address of the memory. For more detailed information including memory map definitions, please see Finisar Application Note AN-2035 "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers", or the XFP MSA Specification1. Finisar Corporation - August 2015 Rev. E1 Page 7 FTLX8512D3BTL Product Specification IX. Mechanical Specifications Finisar's XFP transceivers are compliant with the dimensions defined by the XFP MultiSourcing Agreement (MSA). Bail color is beige. 77.95 22.15 18.35 13.30 8.50 LATCHED 16.00 UNLATCHED 20.85 39.00 R1.00 XFP Transceiver (dimensions are in mm) Finisar Corporation - August 2015 Rev. E1 Page 8 FTLX8512D3BTL Product Specification X. PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) Finisar Corporation - August 2015 Rev. E1 Page 9 FTLX8512D3BTL Product Specification XFP Detail Host Board Mechanical Layout (dimensions are in mm) XFP Recommended Bezel Design (dimensions are in mm) Finisar Corporation - August 2015 Rev. E1 Page 10 FTLX8512D3BTL Product Specification XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), INF-8077i, Rev 4.5 - August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: "Digital Diagnostic Monitoring Interface for XFP Optical Transceivers" - Finisar Corporation, December 2003 3. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment" 4. "Application Note AN-2038: Finisar Implementation Of RoHS Compliant Transceivers" XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation - August 2015 Rev. E1 Page 11