KAOHSIUNG HITACHI ELECTRONICS CO., LTD.
FOR MESSRS: DATE: Oct.28th 2011
CUSTOMER’S ACCEPTANCE SPECIFICATION
TX13D04VM2CAA
Contents
No. ITEM SHEET No. PAGE
1 COVER 7B64PS 2701- TX13D04VM2CAA-1 1-1/1
2 RECORD OF REVISION 7B64PS 2702- TX13D04VM2CAA-1 2-1/1
3 GENERAL DATA 7B64PS 2703- TX13D04VM2CAA-1 3-1/1
4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704- TX13D04VM2CAA-1 4-1/1
5 ELECTRICAL CHARACTERISTICS 7B64PS 2705- TX13D04VM2CAA-1 5-1/1
6 OPTICAL CHARACTERISTICS 7B64PS 2706- TX13D04VM2CAA-1 6-1/2~2/2
7 BLOCK DIAGRAME 7B64PS 2707- TX13D04VM2CAA-1 7-1/1
8 RELIABILITY TESTS 7B64PS 2708- TX13D04VM2CAA-1 8-1/1
9 LCD INTERFACE 7B64PS 2709- TX13D04VM2CAA-1 9-1/7~7/7
10 OUTLINE DIMENSIONS 7B63PS 2710- TX13D04VM2CAA-1 10-1/2~2/2
11 APPEARANCE STANDARD 7B64PS 2711- TX13D04VM2CAA-1 11-1/3~3/3
12 PRECAUTIONS 7B64PS 2712- TX13D04VM2CAA-1 12-1/2~2/2
13 DESIGNATION OF LOT MARK 7B64PS 2713- TX13D04VM2CAA-1 13-1/1~1/1
ACCEPTED BY: PROPOSED BY:
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2701- TX13D04VM2CAA-1 PAGE 1-1/1
2. RECORD OF REVISION
DATE SHEET No. SUMMARY
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2702-TX13D04VM2CAA-1 PAGE 2-1/1
3. GENERAL DATA
3.1 DISPLAY FEATURES
This module is a 5” VGA of 4:3 format of amorphous silicon TFT.The pixel format is vertical stripe and
sub pixels are arranged as R(red), G(green), B(blue) sequentially .This display is RoHS compliant , and
COG (chip on glass) technology and LED backlight are applied on this display.
Part Name TX13D04VM2CAA
Module Dimensions 119.4(W)mm x 89.1(H)mm x 9.3(D)mm typ
LCD Active Area 101.76(W)mm x 76.32(H)mm
Pixel Pitch 0.053(W)mm x 3(R,G,B)(W) x 0.159(H)mm
Resolution 640x3(R,G,B))(W)x480(H) dots
Color Pixel Arrangement R, G, B Vertical stripe
LCD Type Transmissive Color TFT; Normally White
Display Type Active Matrix
Top Polarizer Type Anti-glare Polarizer Film
Number of Colors 262k Colors (R,G,B 6bit digital each)
Backlight Light Emitting Diode (LED)
Weight 110 g (typ.)
Interface 40pin C-MOS
Power Supply Voltage 3.3V for LCD driving
12 V for B / L driving
Power Consumption 1.2 W for LCD ; 3.5 W for B/L
Viewing Direction 12 O’clock (without image inversion and least brightness change)
6 O’clock (contrast peak located at)
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2703-TX13D04VM2CAA-1 PAGE 3-1/1
4. ABSOLUTE MAXIMUM RATINGS
Item Symbol Min. Max. Unit Remarks
Supply Voltage VDD -0.3 5.0 V -
Input Voltage of Logic VI -0.3 VDD+0.3 V Note 1
Operating Temperature Top -30 80
C
Note 2
Storage Temperature Tst -40 90
C
Note 2
Backlight Input Voltage VLED - 15 V -
Note 1: The rating is defined for the signal voltages of the interface such as DCLK, DE, and RGB data
bus.
Note 2: The maximum rating is defined as above based on chamber temperature, which might be
different from ambient temperature after assembling the panel into the application. Moreover,
some temperature-related phenomenon as below needed to be noticed:
- Background color, contrast and response time would be different in temperatures other than
25
C
.
-Operating under high temperature will shorten LED lifetime.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2704-TX13D04VM2CAA-1 PAGE 4-1/1
5. ELECTRICAL CHARACTERISTICS
5.1 LCD CHARACTERISTICS
Item
Symbol
Condition Min. Typ. Max. Unit Remarks
Power Supply Voltage VDD - 3.0 3.3 3.6 V -
Input Voltage of Logic VI “H” level 0.7VDD - VDD+0.3 V Note 1
“L” level -0.3 - 0.25VDD
Power Supply Current IDD VDD=3.3V - 360 410 mA Note 2,3
Vsync Frequency v
f
- 50 60 70 Hz -
Hsync Frequency
H
f - 26.25 31.50 36.75 KHz -
CLK Frequency CL
K
f
- 21.0 25.2 29.4 MHz -
Note1: The rating is defined for the signal voltages of the interface such as DE, DCLK and RGB data
bus.
Note 2: An all black check pattern is used when measuring IDD. v
f
is set to 60 Hz.
Note 3: 1.0A fuse is applied in the module for IDD. For display activation and protection purpose, power
supply is recommended larger than 2.5A to start the display and break fuse once any short
circuit occurred.
5.2 BACKLIGHT CHARACTERISTICS
Item
Symbol
Condition Min. Typ. Max. Unit Remarks
LED Input Voltage VLED - 11.5 12.0 12.5 V Note1
LED Forward Current
(Dim Control) ILED 0V; 0% duty 270 290 320 mA Note 2
3.3VDC; 100% duty - 30 36
LED lifetime - 290 mA - 70K - hrs Note 3
Note 1: As Fig. 5.1 shown, LED current is constant, 290 mA, controlled by the LED driver when
applying 12V VLED.
Note 2: Dimming function can be obtained by applying DC voltage or PWM signal from the display
interface CN1. The recommended PWM signal is 1kHz ~ 10kHz with 3.3V amplitude.
Note 3: The estimated lifetime is specified as t he time to reduce 50% brightness by applying 290 mA at
25
C
.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2705-TX13D04VM2CAA-1 PAGE 5-1/1
0VVSS ,25 CT
a
CT
a
25
Fig 5.1
6. OPTICAL CHARACTERISTICS
The optical characteristics are measured based on the conditions as below:
- Supplying the signals and voltages defined in the section of electrical characteristics.
- The backlight unit needs to be turned on for 30 minutes.
- The ambient temperature is 25
C
.
- In the dark room around 500~1000 lx, the equipment has been set for the measurements as shown in
Fig 6.1.
3.3V
Item
Symbol
Condition Min. Typ. Max. Unit Remarks
Brightness of White -
0 ,0
,
ILED= 290mA
400 600 - 2
cd/m
Note 1
Brightness Uniformity - 70 - - % Note 2
Contrast Ratio CR 250 500 - - Note 3
Response Time
(
Rising + Falling
) fr T T
0 ,0
- - 45 ms Note 4
Viewing Angle
x
10 CR ,0
- 70 -
Degree Note 5
x
10 CR ,180
- 70 -
y
10 CR ,90
- 60 -
y
10 CR ,270
- 60 -
Color
Chromaticity
Red X
0 ,0
0.58 0.63 0.68
- Note 6
Y 0.49 0.34 0.39
Green X 0.32 0.37 0.42
Y 0.51 0.56 0.61
Blue X 0.10 0.15 0.20
Y 0.04 0.09 0.14
White X 0.26 0.31 0.36
Y 0.29 0.34 0.39
Note 1: The brightness is measured from the panel center point, P5 in Fig. 6.2, for the typical value.
Note 2: The brightness uniformity is calculated by the equation as below:
100%
Brightness Max.Brightness Min.
uniformity Brightness
, which is based on the brightness values of the 9 points measured by BM-5 as shown in Fig. 6.2.
Distance: 500 mm
LCD panel
Field:
1
Photo Detector: BM-5
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2706-TX13D04VM2CAA-1 PAGE 6-1/2
VDDHz, 60 25
va
fCT ,
Fig 6.1 Fig 6.2
15%
85%
50%
15% 50% 85%
：measuring points
12 3
6 5 4
78 9
Note 3: The Contrast Ratio is measured from the center point of the panel, P5, and defined as the
following equation:
Black of Brightness Whiteof Brightness
= CR
Note 4: The definition of response time is shown in Fig. 6.3. The rising time is the period from 10%
brightness to 90% brightness when the data is from black to white. Oppositely, Falling time is
the period from 90% brightness rising to 10% brightness.
Fig 6.3
Note 5: The definition of viewing angle is shown in Fig. 6.4. Angle
is used to represent viewing
directions, for instance,
270
means 6 o’clock, and
0
means 3 o’clock. Moreover,
angle
is used to represent viewing angles from axis Z toward plane XY.
The display is super wide viewing angle version, so that the best optical performance can be
obtained from every viewing direction.
3 o'clock
xx'
y
y'
z
z'
,0)y (x,
0
90
180
270
6 o'clock
12 o'clock
9 o'clock
= Viewing angle
Fig 6.4
Note 6: The color chromaticity is measured from the center p oint of th e p anel, P5, a s shown in Fi g. 6.2.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2706-TX13D04VM2CAA-1 PAGE 6-2/2
7. BLOCK DIAGRAM
Note1: Signals are DCLK, DE, and RGB data bus.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2707-TX13D04VM2CAA-1 PAGE 7-1/1
Source Driver with
Timing Controller
Power
Supply
Circuit
Gate Driver
D1 D2 D1920
G1
G2
G480
I/F(CN1)
Data / Clock
Timing Signals
TFT-LCD
Powe
Supply
(LCD)
LED Backlight
LED Driver
Circuit
Power Supply
(B/L)
Dim
(B/L)
8. RELIABILITY TESTS
Test Item Condition
High Temperature
1) Operating
2) 80
C
500 hrs
Low Temperature
1) Operating
2) -30
C
500 hrs
High Temperature
1) Storage
2) 90
C
500 hrs
Low Temperature
1) Storage
2) -40
C
500 hrs
Heat Cycle
1) Operating
2) –30
C
~80
C
3) 3hrs~1hr~3hrs
500 hrs
Thermal Shock
1) Non-Operating
2) -35 C
85
C
3) 0.5 hr
0.5 hr
500 hrs
High Temperature &
Humidity
1) Operating
2) 40
C
& 85%RH 3) Without condensation
4) Note 3
500 hrs
Vibration
1) Non-Operating
2) 10~200 Hz 3) 5G
4) X, Y, and Z directions
1 hr for each direction
Mechanical Shock
1) Non-Operating
2) 10 ms 3) 80G
4)
Y X,
and
Z
directions Once for each direction
ESD
1) Operating
2) Tip:150 pF,330
3) Air discharge for glass:
20KV
4) Contact discharge for metal frame:
20KV
1) Glass: 9 points
2) Metal frame: 8 points
3) Connector: all pins
Restart Test
1) Test period 0.5S(on)→0.5S(off)→0.5S(on) for 5 times
2) Repeat 1) every 5 min. later for 5 times
Operating for 1hr @ 80
C
Operating for 1hr @ -30
C
Note 1: Display functionalities are inspected under the conditions defined in the specification after the
reliability tests.
Note 2: The display is not guaranteed for use in corrosive gas environments.
Note 3: Under the condition of high temperature & humidity, if the temperature is higher than 40
C
, the
humidity needs to be reduced as Fig. 8.1 shown.
Note 4: All pins of LCD interface(CN1) have been tested by
100V contact discharge of ESD under
non-operating condition.
C)(
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2708-TX13D04VM2CAA-1 PAGE 8-1/1
9. LCD INTERFACE
9.1 INTERFACE PIN CONNECTIONS
The display interface connector (CN1) is FA5S040HP1R3000 (JAE),and Pin assignment is as below:
Pin No. Symbol Signal Pin No. Symbol Signal
1 VDD Supply Voltage 21 G4 Green data
2 22 G3 Green data
3 U/D Vertical Display mode
Control 23 VSS Ground
4 L/R Horizontal Display mode
Control 24 G2 Green data
5 NC No Connection 25 G1
Green data
6 DE Data Enable 26 G0 Green data (LSB)
7 VSS Ground 27 VSS Ground
8 DCLK Dot clo ck 28 R5 Red data (MSB)
9 VSS Ground 29 R4 Red data
10 NC No Connection 30 R3 Red data
11 VSS Ground 31 VSS Ground
12 B5 Blue data (MSB) 32 R2 Red data
13 B4 Blue data 33 R1 Red data
14 B3 Blue data 34 R0 Red data (LSB)
15 VSS Ground 35 NC No Connection
16 B2 Blue data 36 DIM Note 1
17 B1 Blue data 37
VLED Power Supply for B/L
18 B0 Blue data (LSB) 38
19 VSS Ground 39
20 G5 Green data (MSB) 40
Note 1: Normal brightness: 0V or 0% PWM duty; Brightness control: 0V to 3.3V DC or 0% to 100%
PWM duty.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-1/7
9.2 TIMING CHART
DE
th = 800 CLK (1H)
12 3 60
RRRRR RRRR
60 CLK (typ.) thd = 640 CLK (fixed) 100CLK (typ.)
700 800
Display data
12
DCLK
GGGGG GGGG
BBBBB BBBB
61
R [0:5]
G [0:5]
B [0:5]
Invalid data Invalid data
25.2M Hz (typ.)
Fig. 9.1 Horizontal Timing
Fig. 9.2 Vertical Timing
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-2/7
9.3 CLOCK AND DATA INPUT TIMING
Fig. 9.3 Setup & Hold Time of Data and DE signal.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-3/7
9.4 TIME TABLE
The column of timing sets including minimum, typical, and maximum as below are based on the best
optical performance, frame frequency (Vsync) = 60 Hz to define. If 60 Hz is not the aim to set, 50~70
Hz for Vsync is recommended to apply for better performance by other parameter combination as the
definitions in section 5.1.
FOR TIMING CHART
Item Symbol Min. Typ. Max. Unit
Horizontal
CLK Frequency fclk 21.0 25.2 29.7 M Hz
Display Data thd 640 640 640 CLK
Cycle Time th 700 800 900
Vertical Display Data tvd 480 480 480 H
Cycle Time tv 500 525 550
FOR CLOCK AND DATA INPUT TIMING
Item Symbol Min. Typ. Max. Unit
DCLK Duty Tcwh 45 50 55 %
Cycle Time Tcph 34 40 -
ns
Data Setup Time Tdsu 12 - -
Hold Time Tdhd 12 - -
DE Setup Time Tesu 12 - -
Hold Time Tehd 12 - -
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-4/7
9.5 POWER SEQUENCE
Note 1
Note 2
0.7VDD
0.3VDD
0.3VLED
VDD
Signals
Backlight
Fig. 9.4 Power Sequence Timing
Note 1: In order to avoid any damages, VDD has to be applied before all other signals. The opposite is
true for power Off where VDD has to be remained on until all other signals have been switch off.
The recommended time period is 1 second. Hot plugging might cause display damage due to
incorrect power sequence, please pay attention on interface connecting before power on.
Note 2: In order to avoid showing uncompleted patterns in transient state. It is recommended that
switching the backlight on is delayed for 1 second after the signals have been applied. The
opposite is true for power Off where the backlight has to be switched off 1 second before the
signals are removed.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-5/7
9.6 SCAN DIRECTION
Scan direction is available to be switched as below by setting CN1’s L/R & U/D pin.
L/R : L , U/D : L L/R : H , U/D : L
(default)
L/R : L , U/D : H L/R : H , U/D : H
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-6/7
9.7 DATA INPUT for DISPLAY COLOR
COLOR &
Gray Scale Data Signal
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0
Basic
Color
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (0) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Green (0) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Blue (0) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Red
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (62) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Red (61) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Red (1) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (0) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Green
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green (62) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
Green (61) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Green (1) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
Green (0) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Blue
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue (61) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
: : : : : : : : : : : : : : : : : : :
: : : : : : : : : : : : : : : : : : :
Blue (1) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0
Blue (0) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2709-TX13D04VM2CAA-1 PAGE 9-7/7
11. APPEARANCE STANDARD
The appearance inspection is performed in a dark room around 500~1000 lx based on the conditions
as below:
- The distance between inspector’s eyes and display is 30 cm.
- The viewing zone is defined with angle
shown in Fig. 11.1 The inspection should be performed
within
45
when display is shut down. The inspection should be performed within
5
when display
is power on.
Fig. 11.1
11.1 THE DEFINITION OF LCD ZONE
LCD panel is divided into 3 areas as shown in Fig.11.2 for appearance specification in next section. A
zone is the LCD active area (dot area); B zone is the area, which extended 1 mm out from LCD active
area; C zone is the area between B zone and metal frame.
In terms of housing design, B zone is the recommended window area customers’ housing should be
located in.
Fig. 11.2
A zone
B zone
C zone
Metal frame
1 m m
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2711-TX13D04VM2CAA-1 PAGE 11-1/3
11.2 LCD APPEARANCE SPECIFICATION
The specification as below is defined as the amount of unex pected phen omenon or material in d ifferent
zones of LCD panel. The definitions of length, width and average diameter using in the table are shown
in Fig. 11.3 and Fig. 11.4.
Item Criteria Applied zone
Scratches
Length (mm) Width (mm) Maximum number Minimum space
A, B
Ignored W≦0.02 Ignored -
L≦40 0.02＜W≦0.04 10 -
L≦20 W≦0.04 10 -
Dent Serious one is not allowed A
Wrinkles in polarizer Serious one is not allowed A
Bubbles on polarizer
Average diameter (mm) Maximum number
A
D≦0.3 Ignored
0.3＜D≦0.5 12
0.5＜D 3
1) Stains
2) Foreign Materials
3) Dark Spot
Filamentous (Line shape)
A, B
Length (mm) Width (mm) Maximum number
L≦2.0 W≦0.03 Ignored
L≦3.0 0.03＜W≦0.05 10
L≦2.5 0.05＜W≦0.1 1
Round (Dot shape)
A, B
Average diameter (mm) Maximum number Minimum Space
D＜0.2 Ignored -
0.2≦D＜0.3 10 10 mm
0.3≦D＜0.4 5 30 mm
0.4≦D None -
In total Filamentous + Round=10
Those wiped out easily are acceptable
Dot-Defect
(Note 1)
Type Maximum number
A
Bright dot-defect
1 dot 4
2 adjacent dot 1
3 adjacent dot or above Not allowed
In total 5
Dark dot-defect
1 dot 5
2 adjacent dot 2
3 adjacent dot or above Not allowed
In total 5
In total 10
Fig. 11.4
a
bAverage diameter = 2ba
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2711-TX13D04VM2CAA-1 PAGE 11-2/3
Note 1: The definitions of dot defect are as below:
- The defect area of the dot must be bigger than half of a dot.
- For bright dot-defect, showing black pattern, the dot’s brightness must be over 30% brighter
than others.
- For dark dot-defect, showing white pattern, the dot’s brightness must be under 70% darker
than others.
- The definition of 1-dot-defect is the defect-dot, which is isolated and no adjacent defect-dot.
- The definition of adjacent dot is shown as Fig. 11.5.
A
The dots colored gray are
adjacent to defect-dot A.
Fig. 11.5
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2711-TX13D04VM2CAA
-1
PAGE 11-3/3
12. PRECAUTIONS
12.1 PRECAUTIONS OF ESD
1) Before handling the display, please ensure your body has been connected to ground to avoid any
damages by ESD. Also, do not touch display’s interface directly when assembling.
2) Please remove the protection film very slowly before turning on the display to avoid generating ESD.
12.2 PRECAUTIONS OF HANDLING
1) In order to keep the appearance of display in good condition, please do not rub any surfaces of the
displays by using sharp tools harder than 3H, especially touch panel, metal frame and polarizer.
2) Please do not stack the displays as this may damage the surface. In order to avoid any injuries,
please avoid touching the edge of the glass or metal frame and wore gloves during handling.
3) Touching the polarizer or terminal pins with bare hand should be avoided to prevent staining and
poor electrical contact.
4) Do not use any harmful chemicals such as acetone, toluene, and isopropyl alcohol to clean d isplay’s
surfaces.
5) Please use soft cloth or absorbent cotton with ethanol to clean the display by gently wiping.
Moreover, when wiping the display, please wipe it by horizontal or vertical direction instead of circling
to prevent leaving scars on the display’s surface, especially polarizer.
6) Please wipe any unknown liquids immediately such as saliva, water or dew on the display to avoid
color fading or any permanent damages.
7) Maximum pressure to the surface of the display must be less than
4
10 x 1.96 Pa. If the area of
applied pressure is less than 1 2
cm , the maximum pressure must be less than 1.96N.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2712-TX13D04VM2CAA
-1
PAGE 12-1/2
12.3 PRECAUTIONS OF OPERATING
1) Please input signals and voltages to the displays according to the values defined in the section of
electrical characteristics to obtain the best performance. Any voltages over than absolute maximum
rating will cause permanent damages to this display. Also any timing of the signals out of this
specification would cause unexpected performance.
2) When the display is operating at significant low temperature the response time will be slower than it
at 25
C
. In high temperature, the color will be slightly dark and blue compared to original pattern.
However these are temperature-related phenomenon of LCD and it will not cause permanent
damages to the display when used within the operating temperature.
3) The use of screen saver or sleep mode is recommended when static images are likely for long
periods of time. This is to avoid the possibility of image sticking.
4) Spike noise can cause malfunction of the circuit. The recommended limitation of spike noise is no
bigger than
100 mV.
12.4 PRECAUTIONS OF STORAGE
If the displays are going to be stored for years, please be aware the following notices.
1) Please store the displays in a dark room to avoid any damages from sunlight and other sources of
UV light.
2) The recommended long term storage temperature is between 10
C
~35
C
and 55%~75% humidity
to avoid causing bubbles between polarizer and LCD glasses and polarizer peeling from LCD
glasses.
3) It would be better to keep the displays in the container which is shipped from Hitachi and do not
unpack it.
4) Please do not stick any labels on the display surface for a long time, especially on the polarizer.
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2712-TX13D04VM2CAA
-1
PAGE 12-2/2
13. DESIGNATION OF LOT MARK
1) The lot mark is showing in Fig.13.1. First 4 digits are used to represent production lot T represented
made in Taiwan and the last 6 digits are the serial number.
2) The tables as below are showing what the first 4 digits of lot mark are shorted for.
Year
2009
2010
2011
2012
2013
9
0
1
2
3
Lot Mark
Lot Mark Lot MarkMonth Month
01
02
03
04
05
06
07
08
09
10
11
12
Jan.
Feb.
Mar.
Apr.
May
Jun.
Jul.
Aug.
Sep.
Oct.
Nov.
Dec.
Week
1~7 days
8~14 days
15~21 days
22~28 days
29~31 days
1
2
3
4
5
Lot Mark
3) Except letters I and O revision number will be shown on lot mark and following letters A to Z.
4) The location of the lot mark is on the back of the display shown in Fig. 13.2.
Fig. 13.2
KAOHSIUNG HITACHI
ELECTRONICS CO., LTD. SHEET
NO.
7B64PS 2713-TX13D04VM2CAA
-1
PAGE 13-1/1
TX13D04VM2CAA
1101T
HITACHI MADE IN TAIWAN
REV:A
123456
(5D)