TDA8380A/N2 - Philips Semiconductors / NXP Semiconductors

DATA SH EET

Product speciﬁcation

Supersedes data of October 1993

File under Integrated Circuits, IC02

November 1993

INTEGRATED CIRCUITS

TDA8380A

Control circuit for switched mode

power supplies

November 1993 2

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

GENERAL DESCRIPTION

The TDA8380A is an integrated circuit intended for use as a control circuit in low-cost switched mode power supplies for

television, monitors and small industrial equipment. The TDA8380A operates using duty factor regulation in the fixed

frequency mode.

Features

•A low-current initialization circuit (maximum 150 µA) which can be switched off

•A bandgap reference generator

•Circuitry for slow-start combined with an accurate setting of the maximum duty factor (Dmax)

•Programmable low supply voltage protection with one default value

•High supply protection circuitry

•Error amplifier with a transfer characteristic generator (TCG)

•Protection against open- and short-circuited feedback loop

•An overload voltage foldback

•Primary current protection circuitry for both cycle-by-cycle and trip mode

•Protection against transformer saturation

•A direct drive output stage (sink current 2.5 A, source current 0.75 A)

•Anti-double pulse logic

•Protected against damage as a result of a short-circuited high-voltage transistor

•RC oscillator with synchronization input

QUICK REFERENCE DATA

PACKAGE OUTLINE

16-lead DIL; plastic (SOT38); SOT38-1 ; 1996 November 18.

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Supply voltage VCC −14 −V

Supply current ICC −−15 mA

Output pulse repetition frequency range fo10 −100 kHz

Operating ambient temperature range Tamb −25 −+70 °C

November 1993 3

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power

supplies TDA8380A

Fig.1 Block diagram.

November 1993 4

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

PINNING

1 E2 Emitter of output source transistor

2 C2 Collector of output source transistor

3 DEM Demagnetization sense input

CCmin Minimum VCC threshold setting

CC Supply voltage

ref Reference current setting

7 FB Feedback input

8 STAB Output error ampliﬁer

9 DUTY Pulse width modulator input

10 COSC Oscillator capacitor

11 SYNC Synchronization input

12 SS Maximum duty factor (Dmax) setting plus slow-start

13 CURR Input current protection

14 VEE Ground

15 E1 Emitter of output sink transistor

16 C1 Collector of output sink transistor

Fig.2 Pinning diagram.

November 1993 5

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

FUNCTIONAL DESCRIPTION

The TDA8380A is a control circuit which generates the pulses required to drive the switching transistor in a switched

mode power supply (SMPS).

Supply

This device is intended to be used on the primary side of the power supply and can be supplied via a take-over (auxiliary)

winding on the transformer.

The device is initialized via a high value resistor connected between the rectified mains voltage and the device’s supply

pin (pin 5), which causes the capacitor connected to this pin to charge slowly. When the voltage exceeds the initialization

level (typically 17 V) the device will start up and the duty cycle will be slowly increased by the slow-start circuit. After a

short period the take-over winding will supply the device. The value of the resistor is normally defined by the time taken

to charge the capacitor.

A one second delay between switching on and operation of the power supply is acceptable in most cases.

The operating voltage range is from 9 to 20 V. The supply pin is protected by a 23 V Zener diode. The supply protection

circuit is activated once the Zener diode is conducting. The slow-start procedure begins after initialization, until then the

output is off. The current drawn by the device during the initialization period is less than 150 µA.

When the supply voltage falls below the minimum trip level, the device switches off and the start-up procedure is

repeated. The minimum voltage supply threshold setting (VCCmin) can be set externally with a resistor connected between

the VCCmin pin (pin 4) and ground (pin 14) (see Fig.3).

VCCmin can be set between 8.4 V (an internally fixed overriding protection level) and 17 V by means of an external resistor

connected to pin 4.

When choosing the initialization and minimum supply voltages the following should be taken into account:

•The difference between the two voltages should be large enough to enable a supply voltage dip during start-up.

•The value of the minimum supply voltage should be high enough to ensure that the high-voltage transistor is correctly

driven. A high protection level makes it possible to have a large resistor value in series with the base drive.

For battery line input operation, the VCCmin pin is connected to VCC, the start-up circuit is then inhibited and the device

starts operating when VCC exceeds the 8.4 V protection level (this level has a hysteresis of approximately 50 mV). The

device draws current continuously under these conditions.

Fig.3 Trip level setting of minimum VCC protection level.

November 1993 6

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Reference block

A bandgap based reference generates a stabilized voltage of 7 V to supply most of the device’s internal circuits, this

decreases chip size and increases reliability. The only circuits connected to VCC are:

•The initialization circuit

•The output circuitry

•The series transistor of the stabilized voltage

By means of a resistor (R6) connected to the Iref input a reference current is defined which determines six other device

settings.

Part of the reference current is used to charge the oscillator capacitor (C10), therefore, the charging time is proportional

to R6×C10. The maximum duty factor (Dmax) is set by the resistor connected to pin 12 (R12) and is defined by the ratio

R6/R12. The minimum supply voltage (pin 5) set by the resistor (R4) at input VCCmin is defined by: 4/6 ×V6×R4/R6.

Oscillator

The oscillator capacitor is charged and discharged between the high and low voltage levels as defined by the bandgap

reference (high voltage typically 5 V and low voltage typically 1.4 V). The charge current is 1/6 of the reference current,

the discharge current having the same value as the reference current. The period is therefore defined by 10 ×R6×C10.

The oscillator flyback pulse is used to set the bistable in the output logic, however the output remains low until the positive

ramp starts (see Fig.4). The oscillator can be synchronized by means of the SYNC pin. When this pin is connected to

VCC, the oscillator is free running. When it is between 0.85 and 5.6 V, the oscillator stops at the low voltage level prior to

the next positive ramp.

Fig.4 Oscillator levels.

November 1993 7

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Synchronization

The synchronisation input (pin 11) can be driven by either an optocoupler or a loosely coupled pulse transformer.

Figure 5 illustrates synchronization using the 0.85 V threshold and a digital signal connected to the SYNC input (for

example, an optocoupler between pin 11 and VCC); the duty factor of the pulse is not very important. The oscillator starts

at the first negative going edge of the sync. signal after the low voltage level has been reached. The synchronization

frequency must be lower than the free running frequency. Synchronization must never affect the period time as this will

corrupt the setting of the maximum duty factor.

In Fig.6 the disabling threshold (5.6 V) is used for synchronization. In this case the oscillator starts at the positive going

edge of the sync. signal.

Fig.5 DC coupled synchronization using the 0.85 V level.

Fig.6 DC coupled synchronization using the 5.6 V level.

November 1993 8

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Figure 7 illustrates synchronization using a pulse transformer. Internal circuitry causes a DC shift which informs the

device that synchronization pulses are present (spikes around 0 V at the output of the pulse transformer) or not present

(DC 0 V at the output of the pulse transformer). When synchronization is not used the SYNC pin must be connected to

VCC, it must not be connected directly to ground or left open.

Fig.7 Synchronization using a pulse transformer.

Synchronization pulses present. Synchronization pulses not present.

November 1993 9

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Error ampliﬁer

The error amplifier compares the feedback voltage of the SMPS with a reference voltage (nominally 2.5 V). The amplifier

output at pin 8 enables gain setting. The amplifier is stable for a gain greater than 20 dB.

The output of the error amplifier is not internally connected to the Pulse Width Modulator (PWM). One input to the PWM

is available at the DUTY input (pin 9) via the Control Slicing Level (CSL) circuit. Normally the STAB and DUTY pins are

connected together, but direct driving of pin 9 via an optocoupler from the secondary side is also possible. A type of

current mode control can be achieved by mixing the STAB signal with the primary current signal before applying it to the

DUTY input.

The feedback (FB) input (pin 7) is used as the input to the Transfer Characteristic Generator (TCG) circuit which ensures

well defined duty factors at low FB voltages; a voltage foldback is an inherent characteristic. In Fig.8, the duty factor is

shown as a function of the voltages at the FB, DUTY and SS inputs. The input which gives the lowest duty factor overrides

the others.

The left hand curve is passed through during a slow-start (via the slow-start input pin 12) when the duty cycle slowly

increases linearly with respect to V12. The right-hand curve is passed through at start-up. The FB voltage slowly

increases from zero and the duty factor, starting at 12%, increases until the maximum duty factor (Dmax) is reached. A

few hundred millivolts later, the FB voltage reaches the start of the regulation curve which is at approximately 2.5 V. The

plateau area between reaching Dmax and starting the regulation curve is kept as small as possible (typically 200 mV).

Due to the characteristics of the TCG, and the fact that an open FB input results in a low voltage at the FB input, open-

and short-circuit feedback loops will result in low duty factors. When DC feedback is used across the error amplifier, the

current capability of the error amplifier must be considered when determining the feedback resistor value.

When the input to the PWM (pin 9) is driven by an optocoupler, the TCG can be used when a rough primary voltage is

applied to the FB input. In this situation an open feedback loop will cause an increase in the FB voltage as the duty factor

rises to its maximum. As soon as the FB voltage exceeds the reference by 0.7 V, the slow-start is triggered.

Fig.8 The duty factor as a function of the FB, SS and DUTY voltages.

November 1993 10

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Demagnetization sense circuit

To enable the SMPS to be kept in the non-continuous mode, an input is available which delays switch-on of the

high-voltage transistor until the transformer currents have decayed to zero. This is an effective way of avoiding

transformer saturation. The waveforms illustrated by Fig.9 show demagnetization with respect to the application diagram

of Fig.13.

As long as the voltage of the take-over (auxiliary) winding (also used for supplying the device) is above 0.6 V (V3) the

output will be prevented from switching on.

Over-current protection

The over-current protection circuit (pin 13) senses the voltage across resistor Rs (see Fig.13), which reflects the primary

current. This generated voltage is negative-going as the emitter of the high-voltage power transistor is grounded (this

circuit arrangement provides the IC with the best safeguard against a possible collector-emitter short-circuit in the power

transistor). At pin 13, the negative voltage signal is shifted to a positive level by a voltage across resistor R13. This voltage

is set by the reference current at pin 13 and is defined by resistor R6 at the Iref input (pin 6) and = 1/6 ×Vref/R6.

Therefore Vshift(VR 13) = Vref/6 ×R13/R6 or nominal 0.416 ×R13/R6 (V).

The positive current monitor voltage at pin 13 is compared with two voltage levels: the first level = 0.2 V and the second

level = 0 V (see Fig.10).

The first trip level only switches off the high-voltage transistor for a cycle and puts the SMPS in a continuous

cycle-by-cycle current protection mode.

The second trip level is only activated when the primary current rise is very fast which can occur during a short-circuited

output. In this mode the high-voltage transistor is quickly switched off and the slow-start procedure is activated.

The difference between the first and second primary current peak levels is set by Rs:

I2−I1 = 0.2/Rs.

The absolute peak values are set by R6 and R13:

I2×Rs = 0.416 ×R13/R6 or

I1×Rs = (0.416 ×R13/R6)−0.2

Fig.9 Demagnetization function.

November 1993 11

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Slow-start circuit

A slow-start occurs:

•At Switch-on of the SMPS

•After a current trip as described in the section Over-current protection

•After a low or high VCC trip.

The capacitor at the SS input is discharged and the slow-start bistable is reset when the voltage at the SS input falls

below 0.5 V after which the circuit is ready for a slow-start. The dead time (during which the capacitor at the SS input is

being charged to the 1.4 V lower level of the sawtooth) before duty cycle regulation starts is minimal. The SS input can

also be used for Dmax setting by connecting a resistor to ground. The voltage across this resistor is then limited to

1/6 ×Vref ×R12/R6.

Output stages

The output stage consists of two NPN darlington transistors, their collector and emitter connected to separate pins (see

Fig.13). The top transistor is capable of sourcing a maximum of 0.75 A to the high-voltage transistor while the bottom

transistor can sink peak currents up to 2.5 A.

For low currents up to 10 mA, the saturation voltage of the sink darlington transistor is similar to that of a single transistor

(see Fig.11). During switching of this transistor dV/dt is internally limited to reduce interference.

Care should be taken with the external wiring of the output pins to avoid oscillation or interference due to parasitic

inductance and wire resistance.

During start-up a small current flows from VCC to E2 to precharge the series capacitor at the output (see Fig.13).

Fig.10 Current protection.

November 1993 12

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Fig.11 Saturation curve.

November 1993 13

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

THERMAL RESISTANCE

PARAMETER SYMBOL MIN. TYP. MAX. UNIT

Voltage

pin 5 (VCC)−0.5 −20 V

pins 1, 2, 4 and 16 −0.5 −VCC V

pins 3 and 13 −0.5 −0.5 V

pins 7 and 9 −0.5 −6.5 V

pin 11 0.6 −VCC V

Currents

pins 5 (VCC)0−20 mA

pin 1 −0.75 −0A

pin 2 0 −0.75 A

pins 3, 4, 6 to 8 and 10 to 12 −10 −10 mA

pin 13 −200 −10 mA

pin 15 −2.5 −0A

pin 16 0 −2.5 A

Total power dissipation Ptot see Fig.12

Operating ambient temperature range

(for dissipation ≤1W) T

amb −25 −+70 °C

Storage temperature range Tstg −55 −+150 °C

From junction to ambient (in free air) Rth j−a(max) = 55 K/W

Fig.12 Power derating curve.

November 1993 14

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

CHARACTERISTICS

VCC = 14 V; Tamb = 25 °C; reference resistor = 5 kΩ unless otherwise speciﬁed

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply

Supply voltage VCC 9−20 V

Supply initialization level V515 17 18 V

High voltage protection V521 23 25 V

Internal ﬁxed minimum

protection level V57.9 8.4 8.9 V

Hysteresis dVCC −50 −mV

Supply current

operational ICC −−15 mA

before initialization ICC −100 150 µA

Reference current (pin 4) note 1 I4I6/5.7 I6/6 I6/6.4 mA

Trigger level VCCmin setting V53.6V43.8V44.2V4V

Clamp voltage at 20 mA 21.5 23.5 25.5 V

Reference (pin 6)

Reference voltage Vref 2.4 2.5 2.6 V

Current range Iref 200 −800 µA

Reference voltage over

I6 range dVref −20 −+20 mV

Error ampliﬁer

Error ampliﬁer threshold VCC = 8.5 to 20 V V72.4 2.5 2.6 V

Input current I70−5µA

Sink current output at 1.2 V I81−−mA

Source current output at 5.5 V I880 100 130 µA

Open loop gain A0 −100 −dB

Unity gain bandwidth BW −5−MHz

Input DUTY current note 1 I9I6/5.7 I6/6 I6/6.3 mA

High FB protection level V72.95 3.1 3.25 V

Temperature coefﬁcient of

error amplifier threshold dV7/dT −100 −10−6/K

TCG function (see Fig.8)

Transfer characteristics dD/dV7−32 −%/V

Minimum duty factor Dmin −12 −%

Plateau width V7−200 −mV

November 1993 15

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Slow-start function

Transfer characteristics dD/dV12 −23.8 −%/V

Input current note 1 I12 I6/5.7 I6/6 I6/6.3 mA

Sink current during faults at 0.5 V I12 8−−mA

Internally ﬁxed maximum

duty factor Dmax 75 80 85 %

Clamp current at V12 = 0.5 V I12 −−2−mA

Output stage

Source transistor

Voltage drop with respect

to VCC at 0.75 A VCC−V1−2−V

Pull-up current VCC −V1 = 15 V −I125 −100 µA

Operating current range −I10−0.75 A

Sink transistor

(see Fig.11)

Saturation voltage

at 2.5 A V16 −V15 −2−V

at 1 A V16 −V15 −1.5 −V

at 10 mA V16 −V15 −0.3 −V

Leakage current V16 −V15 = 20 V I16 −−1µA

Falling edge dV16−15/dt −0.2 −V/ns

Operating current range

Peak I16 0−2.5 A

Average I16 −−250 mA

Oscillator

High level voltage V10 −5−V

Low level voltage V10 −1.4 −V

Charge current note 1 I10 I6/5.7 I6/6 I6/6.3 mA

Frequency range fo10 −100 kHz

Frequency R6 = 5 kΩ

C10 = 680 pF fo27 28.5 30 kHz

Temperature coefﬁcient of

the frequency df/dT −100 −10−6/K

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

November 1993 16

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Note to the characteristics

1. Over the current range of I6; 200 to 800 µA.

Synchronization

Minimum synchronization

pulse width t11 −−0.5 µs

Switching threshold V11 0.7 0.85 0.9 V

Input current I11 2.5 5.0 7.5 µA

Disabling threshold V11 4.2 5.6 6.0 V

Input voltage at −700 µAV

11 390 −550 mV

Demagnetization input

Switching voltage level V3615 645 675 mV

Switching current level I3−23 −−39 µA

Current range of clamp

circuits I3−10 −+10 mA

Clamp level positive at 10 mA V3−950 −mV

Clamp level negative at −10 mA V3−−800 −mV

Temperature coefﬁcient TC −−1.9 −mV/K

Current protection

Input current note 1 I13 I6/5.7 I6/6 I6/6.3 mA

First threshold V13 190 200 210 mV

Second threshold V13 −10 0 10 mV

Delay to switch output via pulse at pin 13

level 1 from 300 mV to

100 mV;

IO= 500 mA −−350 −ns

Delay to switch output via pulse at pin 13

level 2 from 300 mV to

−200 mV;

IO= 500 mA −−300 500 ns

First threshold including

R13 (12 kΩ)R

= 5 kΩ− −−800 −mV

Threshold for open pin

detection V13 −3.5 −V

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

November 1993 17

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power

supplies TDA8380A

Fig.13 Simplified application diagram.

November 1993 18

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

Fig.14 Input and output loading diagram.

November 1993 19

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

PACKAGE OUTLINE

UNIT A

max. 1 2 b1cEe M

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC EIAJ

inches

DIMENSIONS (inch dimensions are derived from the original mm dimensions)

SOT38-1 92-10-02

95-01-19

min. A

max. bmax.

1.40

1.14

0.055

0.045

0.53

0.38 0.32

0.23 21.8

21.4

0.86

0.84

6.48

6.20

0.26

0.24

3.9

3.4

0.15

0.13

0.2542.54 7.62

0.30

8.25

7.80

0.32

0.31

9.5

8.3

0.37

0.33

2.2

0.087

4.7 0.51 3.7

0.15 0.021

0.015 0.013

0.009 0.010.100.0200.19

050G09 MO-001AE

(e )

seating plane

pin 1 index

0 5 10 mm

scale

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

(1) (1)

D(1)

DIP16: plastic dual in-line package; 16 leads (300 mil); long body SOT38-1

November 1993 20

Philips Semiconductors Product speciﬁcation

Control circuit for switched mode power supplies TDA8380A

SOLDERING

Introduction

There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and

surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for

surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often

used.

This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our

“IC Package Databook”

(order code 9398 652 90011).

Soldering by dipping or by wave

The maximum permissible temperature of the solder is 260 °C; solder at this temperature must not be in contact with the

joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds.

The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the

specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may

be necessary immediately after soldering to keep the temperature within the permissible limit.

Repairing soldered joints

Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more

than 2 mm above it. If the temperature of the soldering iron bit is less than 300 °C it may remain in contact for up to

10 seconds. If the bit temperature is between 300 and 400 °C, contact may be up to 5 seconds.

DEFINITIONS

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices, or systems where malfunction of these

products can reasonably be expected to result in personal injury. Philips customers using or selling these products for

use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such

improper use or sale.

Data sheet status

Objective speciﬁcation This data sheet contains target or goal speciﬁcations for product development.

Preliminary speciﬁcation This data sheet contains preliminary data; supplementary data may be published later.

Product speciﬁcation This data sheet contains ﬁnal product speciﬁcations.

Limiting values

Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or

more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation

of the device at these or at any other conditions above those given in the Characteristics sections of the speciﬁcation

is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the speciﬁcation.