1N5820, 1N5821, 1N5822 1N5820 and 1N5822 are Preferred Devices Axial Lead Rectifiers This series employs the Schottky Barrier principle in a large area metal-to-silicon power diode. State-of-the-art geometry features chrome barrier metal, epitaxial construction with oxide passivation and metal overlap contact. Ideally suited for use as rectifiers in low-voltage, high-frequency inverters, free wheeling diodes, and polarity protection diodes. Features * * * * * * Extremely Low VF Low Power Loss/High Efficiency Low Stored Charge, Majority Carrier Conduction Shipped in plastic bags, 500 per bag Available Tape and Reeled, 1500 per reel, by adding a "RL'' suffix to the part number These devices are manufactured with a Pb-Free external lead finish only* http://onsemi.com SCHOTTKY BARRIER RECTIFIERS 3.0 AMPERES 20, 30, 40 VOLTS Mechanical Characteristics: * Case: Epoxy, Molded * Weight: 1.1 gram (approximately) * Finish: All External Surfaces Corrosion Resistant and Terminal * * Leads are Readily Solderable Lead and Mounting Surface Temperature for Soldering Purposes: 220C Max. for 10 Seconds, 1/16 in from case Polarity: Cathode indicated by Polarity Band AXIAL LEAD CASE 267-05 (DO-201AD) STYLE 1 MARKING DIAGRAM 1N 582x 1N582x = Device Code x = 0, 1 or 2 ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. Preferred devices are recommended choices for future use and best overall value. *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. Semiconductor Components Industries, LLC, 2004 December, 2004 - Rev. 6 1 Publication Order Number: 1N5820/D 1N5820, 1N5821, 1N5822 MAXIMUM RATINGS Symbol 1N5820 1N5821 1N5822 Unit Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage Rating VRRM VRWM VR 20 30 40 V Non-Repetitive Peak Reverse Voltage VRSM 24 36 48 V VR(RMS) 14 21 28 V RMS Reverse Voltage Average Rectified Forward Current (Note 1) VR(equiv) 0.2 VR(dc), TL = 95C (RJA = 28C/W, P.C. Board Mounting, see Note 5) IO Ambient Temperature Rated VR(dc), PF(AV) = 0 RJA = 28C/W TA Non-Repetitive Peak Surge Current (Surge applied at rated load conditions, half wave, single phase 60 Hz, TL = 75C) Operating and Storage Junction Temperature Range (Reverse Voltage applied) Peak Operating Junction Temperature (Forward Current applied) A 3. 0 90 85 80 C IFSM 80 (for one cycle) A TJ, Tstg 65 to +125 C TJ(pk) 15 C Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. *THERMAL CHARACTERISTICS (Note 5) Characteristic Thermal Resistance, Junction-to-Ambient Symbol Max Unit RJA 28 C/W Unit *ELECTRICAL CHARACTERISTICS (TL = 25C unless otherwise noted) (Note 1) Symbol Characteristic Maximum Instantaneous Forward Voltage (Note 2) (iF = 1.0 Amp) (iF = 3.0 Amp) (iF = 9.4 Amp) VF Maximum Instantaneous Reverse Current @ Rated dc Voltage (Note 2) TL = 25C TL = 100C iR 1N5820 1N5821 1N5822 0.370 0.475 0.850 0.380 0.500 0.900 0.390 0.525 0.950 V mA 2.0 20 2.0 20 2.0 20 1. Lead Temperature reference is cathode lead 1/32 from case. 2. Pulse Test: Pulse Width = 300 s, Duty Cycle = 2.0%. *Indicates JEDEC Registered Data for 1N5820-22. ORDERING INFORMATION Package Shipping 1N5820 Axial Lead 500 Units/Bag 1N5820RL Axial Lead 1500/Tape & Reel 1N5821 Axial Lead 500 Units/Bag 1N5821RL Axial Lead 1500/Tape & Reel 1N5822 Axial Lead 500 Units/Bag 1N5822RL Axial Lead 1500/Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 1N5820, 1N5821, 1N5822 NOTE 3 -- DETERMINING MAXIMUM RATINGS use in common rectifier circuits, Table 1 indicates suggested factors for an equivalent dc voltage to use for conservative design, that is: VR(equiv) = V(FM) F (4) The factor F is derived by considering the properties of the various rectifier circuits and the reverse characteristics of Schottky diodes. Reverse power dissipation and the possibility of thermal runaway must be considered when operating this rectifier at reverse voltages above 0.1 VRWM. Proper derating may be accomplished by use of equation (1). TA(max) = TJ(max) RJAPF(AV) RJAPR(AV)(1) where TA(max) = Maximum allowable ambient temperature TJ(max) = Maximum allowable junction temperature (125C or the temperature at which thermal runaway occurs, whichever is lowest) PF(AV) = Average forward power dissipation PR(AV) = Average reverse power dissipation RJA = Junction-to-ambient thermal resistance EXAMPLE: Find TA(max) for 1N5821 operated in a 12-volt dc supply using a bridge circuit with capacitive filter such that IDC = 2.0 A (IF(AV) = 1.0 A), I(FM)/I(AV) = 10, Input Voltage = 10 V(rms), RJA = 40C/W. Step 1. Find VR(equiv). Read F = 0.65 from Table 1, Figures 1, 2, and 3 permit easier use of equation (1) by taking reverse power dissipation and thermal runaway into consideration. The figures solve for a reference temperature as determined by equation (2). TR = TJ(max) RJAPR(AV) VR(equiv) = (1.41) (10) (0.65) = 9.2 V. Step 2. Find TR from Figure 2. Read TR = 108C @ VR = 9.2 V and RJA = 40C/W. (2) Step 3. Find PF(AV) from Figure 6. **Read PF(AV) = 0.85 W Substituting equation (2) into equation (1) yields: @ TA(max) = TR RJAPF(AV) (3) I (FM) 10 and I F(AV) 1.0 A. I (AV) Step 4. Find TA(max) from equation (3). TA(max) = 108 (0.85) (40) = 74C. **Values given are for the 1N5821. Power is slightly lower for the 1N5820 because of its lower forward voltage, and higher for the 1N5822. Variations will be similar for the MBR-prefix devices, using PF(AV) from Figure 6. Inspection of equations (2) and (3) reveals that TR is the ambient temperature at which thermal runaway occurs or where TJ = 125C, when forward power is zero. The transition from one boundary condition to the other is evident on the curves of Figures 1, 2, and 3 as a difference in the rate of change of the slope in the vicinity of 115C. The data of Figures 1, 2, and 3 is based upon dc conditions. For Table 1. Values for Factor F Circuit Half Wave Full Wave, Bridge Full Wave, Center Tapped* Load Resistive Capacitive* Resistive Capacitive Resistive Capacitive Sine Wave 0.5 1.3 0.5 0.65 1.0 1.3 Square Wave 0.75 1.5 0.75 0.75 1.5 1.5 *Note that VR(PK) 2.0 Vin(PK). Use line to center tap voltage for Vin. http://onsemi.com 3 1N5820, 1N5821, 1N5822 125 20 15 TR , REFERENCE TEMPERATURE ( C) TR , REFERENCE TEMPERATURE ( C) 125 10 8.0 115 105 RJA (C/W) = 70 50 95 40 28 85 75 15 10 115 8.0 105 RJA (C/W) = 70 50 95 40 28 85 75 2.0 3.0 4.0 5.0 7.0 15 10 20 3.0 4.0 5.0 7.0 15 10 30 20 VR, REVERSE VOLTAGE (VOLTS) VR, REVERSE VOLTAGE (VOLTS) Figure 1. Maximum Reference Temperature 1N5820 Figure 2. Maximum Reference Temperature 1N5821 40 125 20 10 8.0 105 RJA (C/W) = 70 95 50 40 85 30 25 20 15 10 BOTH LEADS TO HEATSINK, EQUAL LENGTH 5.0 28 75 4.0 MAXIMUM TYPICAL 35 15 115 R JL , THERMAL RESISTANCE JUNCTION-TO-LEAD ( C/W) TR , REFERENCE TEMPERATURE ( C) 20 0 5.0 7.0 10 15 20 30 40 0 1/8 2/8 3/8 4/8 5/8 6/8 7/8 VR, REVERSE VOLTAGE (VOLTS) L, LEAD LENGTH (INCHES) Figure 3. Maximum Reference Temperature 1N5822 Figure 4. Steady-State Thermal Resistance 1.0 r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) 1.0 0.5 0.3 0.2 0.1 The temperature of the lead should be measured using a thermocouple placed on the lead as close as possible to the tie point. The thermal mass connected to the tie point is normally large enough so that it will not significantly respond to heat surges generated in the diode as a result of pulsed operation once steady-state conditions are achieved. Using the measured value of TL, the junction temperature may be determined by: TJ = TL + TJL LEAD LENGTH = 1/4 Ppk Ppk tp TIME t1 DUTY CYCLE = tp/t1 PEAK POWER, Ppk, is peak of an equivalent square power pulse. TJL = Ppk * RJL [D + (1 - D) * r(t1 + tp) + r(tp) - r(t1)] where: TJL = the increase in junction temperature above the lead temperature. r(t) = normalized value of transient thermal resistance at time, t, i.e.: r(t1 + tp) = normalized value of transient thermal resistance at time t1 + tp, etc. 0.05 0.03 0.02 0.01 0.2 0.5 1.0 2.0 5.0 10 20 50 t, TIME (ms) 100 200 Figure 5. Thermal Response http://onsemi.com 4 500 1.0 k 2.0 k 5.0 k 10 k 20 k PF(AV) , AVERAGE POWER DISSIPATION (WATTS) 1N5820, 1N5821, 1N5822 10 7.0 5.0 NOTE 4 - APPROXIMATE THERMAL CIRCUIT MODEL SINE WAVE I (FM) (ResistiveLoad) I (AV) 3.0 2.0 1.0 0.7 0.5 Capacitive Loads RS(A) 0.1 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 IF(AV), AVERAGE FORWARD CURRENT (AMP) Figure 6. Forward Power Dissipation 1N5820-22 TC(A) TJ Mounting Method 1 P.C. Board where available copper surface is small. NOTE 5 -- MOUNTING DATA Data shown for thermal resistance junction-to-ambient (R JA) for the mountings shown is to be used as typical guideline values for preliminary engineering, or in case the tie point temperature cannot be measured. TYPICAL VALUES FOR RJA IN STILL AIR TC(K) TL(K) 1/8 1/4 1/2 3/4 RJA 1 50 51 53 55 C/W 2 58 59 61 63 C/W 28 E EEEEEEE E EEEEEEE E E E EEEEEEEE EEEEEEEE L Mounting Method 3 P.C. Board with 2-1/2, x 2-1/2, copper surface. L L = 1/2 Mounting Method 2 Lead Length, L (in) Mounting Method 3 TA(K) Use of the above model permits junction to lead thermal resistance for any mounting configuration to be found. For a given total lead length, lowest values occur when one side of the rectifier is brought as close as possible to the heat sink. Terms in the model signify: TA = Ambient Temperature TC = Case Temperature TL = Lead Temperature TJ = Junction Temperature RS = Thermal Resistance, Heatsink to Ambient RL = Thermal Resistance, Lead-to-Heatsink RJ = Thermal Resistance, Junction-to-Case PD = Total Power Dissipation = PF + PR PF = Forward Power Dissipation PR = Reverse Power Dissipation (Subscripts (A) and (K) refer to anode and cathode sides, respectively.) Values for thermal resistance components are: RL = 42C/W/in typically and 48C/W/in maximum RJ = 10C/W typically and 16C/W maximum The maximum lead temperature may be found as follows: TL = TJ(max) TJL where TJL RJL * PD TJ 125C 0.3 RS(K) SQUARE WAVE 0.2 0.2 RL(K) RJ(K) PD TL(A) 5.0 10 20 RJ(A) TA(A) dc 0.3 0.1 RL(A) L L VECTOR PUSH-IN TERMINALS T-28 C/W http://onsemi.com 5 BOARD GROUND PLANE 1N5820, 1N5821, 1N5822 100 IFSM , PEAK HALF-WAVE CURRENT (AMP) 50 30 20 TJ = 100C 7.0 5.0 25C 3.0 50 TL = 75C f = 60 Hz 30 20 1 CYCLE SURGE APPLIED AT RATED LOAD CONDITIONS 10 2.0 1.0 3.0 20 5.0 7.0 10 30 50 70 100 NUMBER OF CYCLES 2.0 Figure 8. Maximum Non-Repetitive Surge Current 1.0 100 0.7 50 0.5 20 TJ = 125C 10 IR , REVERSE CURRENT (mA) i F, INSTANTANEOUS FORWARD CURRENT (AMP) 10 70 0.3 0.2 0.1 0.07 0.05 100C 5.0 2.0 75C 1.0 0.5 0.2 25C 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 0.05 vF, INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 1N5820 1N5821 1N5822 0.02 Figure 7. Typical Forward Voltage 0.01 0 4.0 8.0 12 16 20 24 28 32 36 40 VR, REVERSE VOLTAGE (VOLTS) C, CAPACITANCE (pF) 500 Figure 9. Typical Reverse Current 1N5820 300 NOTE 6 -- HIGH FREQUENCY OPERATION 200 1N5821 TJ = 25C f = 1.0 MHz Since current flow in a Schottky rectifier is the result of majority carrier conduction, it is not subject to junction diode forward and reverse recovery transients due to minority carrier injection and stored charge. Satisfactory circuit analysis work may be performed by using a model consisting of an ideal diode in parallel with a variable capacitance. (See Figure 10.) 100 1N5822 70 0.5 0.7 1.0 2.0 3.0 5.0 7.0 10 20 30 VR, REVERSE VOLTAGE (VOLTS) Figure 10. Typical Capacitance http://onsemi.com 6 1N5820, 1N5821, 1N5822 PACKAGE DIMENSIONS AXIAL LEAD CASE 267-05 (DO-201AD) ISSUE G K A D 1 B 2 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. DIM A B D K K INCHES MIN MAX 0.287 0.374 0.189 0.209 0.047 0.051 1.000 --- MILLIMETERS MIN MAX 7.30 9.50 4.80 5.30 1.20 1.30 25.40 --- STYLE 1: PIN 1. CATHODE (POLARITY BAND) 2. ANODE http://onsemi.com 7 1N5820, 1N5821, 1N5822 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 http://onsemi.com 8 For additional information, please contact your local Sales Representative. 1N5820/D