SDKN 0.5A 125V AC Qualified Type Detector Compact and low-profile for primary / secondary switching with compatibility to low level rating Ratings and Safety Standards Items Specifications Slide Ratings satisfying local electrical appliance and material safety law 0.5A 125V AC 0.25A 250V AC DC ratings 5mA 5V DC Push Product Line Rotary Circuit arrangement Rating SPDT 0.5A 125V AC 0.25A 250V AC 5mA 5V DC Total travel mm Operating force 9 3.51N Mounting method Operation type Japan Export 250 1,250 Push Snap-in 9.7 Minimum order unitpcs. 21.5N Lever Product No. Drawing No. SDKNA20900 1 SDKNA20700 2 Power Note Safety standard approval must be obtained as a set. Number of packagespcs. 1 case /Japan 1 case /export packing 250 1,250 Export package measurementsmm 389x276x380 Unit:mm No. Style Mounting hole dimensions Rocker Type Push 11.3 8.5 6 Off position of circuit c-2 R1 11.3 7.9 4.2 Direction of insertion t 1.7 R 15.75 6.5 2 Rotary Type 1 Total travel position 22.9 On position of circuit c-1 13 11.2 Slide Type 15 25 14.4min. Push Type Dimensions 12.5min. Dual-in-line Package Type Packing Specifications Bulk 15 t=0.8-1.5mm Terminal No. 1 11 154 Terminal No. c Terminal No. 2 SDKN0.5A 125V AC Qualified Type Unit:mm No. Style Mounting hole dimensions 25 11.3 15 Slide Lever Detector Dimensions 22.9 Within the ON range of the C-1 circuit 11 Within the OFF range of the C-2 circuit 1.7 t R 14.1 min. 12.2 min. Direction of insertion 15 t=0.8-1.5mm Terminal No.2 Terminal No.C Connector corresponds to [HLP-03V], manufactured by the J.S.T. Mfg. Co., Ltd. C 2 Dual-in-line Package Type Note Circuit Diagram Power Terminal No.1 11 SPDT Rotary 15.5 5.5 3 2 R1 11.2 8 2 Push Total travel position 0. 1.8 R 5.1 1.7 1 Push Type 0.5A 125V AC Qualified Type / Cautions Slide Type Rotary Type 1Setting of thresh voltage A 4V or larger voltage difference between switch ON and OFF is recommended. Thresh voltage should be set to the center. Rocker Type 1. This product does not have a water-proof or drip-proof construction. Prevent ingress of water into the switch. Avoid using around spilt or flowing. It may cause deterioration of the insulation. 2. Do not apply load on the connecter or lead wirecodeattached to the product. Using the product with load applied on the connecter / lead wire might cause terminal wobble or contact failures. 3. ON / OFF signal readingFor DC ratings Shall be considered when designing circuit and software as follows. 4V min. Thresh voltage 0V 2ON / OFF signal reading ON / OFF signal reading intervals should be at a minimum of 50ms with at least 3 repetitions. Reading of micro-computer Times 1 2 3 50ms min. 4. Verify the performance under actual product conditions before use. 155 Power Switches List of Varieties Type Push Detector Series Rocker SDKR SDDH SDKN 0.5A 250V AC 1A 125V AC 10mA 5V DC Ratingmax.:4.5A 12V DC Lamp load: 27Wx2 Ratingmin.:10A 12V DC Resistive load 0.25A 250V AC 0.5A 125V AC 5mA 5V DC SDDJE 1 SDDJF 1 10AGP 250V AC 6A / 96A 250V 16AGP 250V AC 166/ 250 2 2 Photo Slide Rating Push 100,000cycles Operating life 5,200cycles 10,000cycles 100,000 cycles 0.5A 250V AC 0.25A 250V AC 10A 250V AC 16A 250V AC Rotary Power Dual-in-line Package Type Travelmm 1.5 3.7 9 9.7 3.4 5.2 Features Water-proof type With signal circuit Water-proof (IP68 rating -- -- -- Operating temperature range -10 to 85 -15 to80 -20 to 60 Automotive use -- -- 100m max. AC switch 500m max.DC switch 500m max. 100m max. 100m max. 100M min. 500V DC 500M min. 500V DC -10 to 55 -- -- Life cycle (availability) Contact resistance Electrical performance Insulation resistance Push Type Voltage proof Terminal strength Rocker Type Mechanical performance Operating Actuator direction strength Perpendicular direction Slide Type Environmental performance 500M min. 500V DC AC switch 10M min. 500V DC 100M min. 100V DC DC switch 1000V AC for 1minute AC switch 500V AC for 1minute 600V AC for 1minute 100V AC for 1minute DC switch 2,000V AC for 1minute Slider pull-out strength: 100N min. 50N for 1minute 50N for 1minute 60N for 1minute Lead terminal Lead terminal 5N for 1minute 10N for 1minute (Right-angle terminal) (Right-angle terminal) 20N 25N 30N 25N 5N for 1minute 100N 20N -- -- Rotary Type Cold -20 240h -15 96h -30 192h -20 96h Dry heat 85 240h 80 96h 70 192h 85 96h Damp heat 60, 90 to 95%RH 1000h 40, 90 to 95%RH 96h 40, 90 to 95%RH 192h 40, 90 to 95%RH 96h 152 153 154 Page 156 160 Power Switches Soldering Conditions 168 Power Switches Cautions 168 Power Switches Safety Standard 168 Notes 1. 1. Dip soldering can be used on SDDJE for PC board terminal and SDDJF right angle terminal types only. 2. 2. T he operating temperature range can be raised upon request. Please contact us for details. 3. Indicates applicability to all products in the series. 150