LM25069 LM25069 Positive Low Voltage Power Limiting Hot Swap Controller Literature Number: SNVS607D LM25069 Positive Low Voltage Power Limiting Hot Swap Controller General Description Features The LM25069 positive hot swap controller provides intelligent control of the power supply voltage to the load during insertion and removal of circuit cards from a live system backplane or other "hot" power sources. The LM25069 provides in-rush current control to limit system voltage droop and transients. The current limit and power dissipation in the external series pass N-Channel MOSFET are programmable, ensuring operation within the Safe Operating Area (SOA). The POWER GOOD output indicates when the output voltage is within 1.3V of the input voltage. The input under-voltage and over-voltage lockout levels and hysteresis are programmable, as well as the initial insertion delay time and fault detection time. The LM25069-1 latches off after a fault detection, while the LM25069-2 automatically restarts at a fixed duty cycle. The LM25069 is available in a 10 pin MSOP package. Operating range: +2.9V to +17V In-rush current limit for safe board insertion into live power sources Programmable maximum power dissipation in the external pass device Adjustable current limit Circuit breaker function for severe over-current events Internal high side charge pump and gate driver for external N-channel MOSFET Adjustable under-voltage lockout (UVLO) and hysteresis Adjustable over-voltage lockout (OVLO) and hysteresis Initial insertion timer allows ringing and transients to subside after system connection Programmable fault timer avoids nuisance trips Active high open drain POWER GOOD output Available in latched fault and automatic restart versions Applications Server Backplane Systems Base Station Power Distribution Systems Solid State Circuit Breaker Package MSOP-10 Typical Application 30086701 Positive Power Supply Control (c) 2010 National Semiconductor Corporation 300867 www.national.com LM25069 Positive Low Voltage Power Limiting Hot Swap Controller December 9, 2010 LM25069 Connection Diagram 30086702 Top View 10-Lead MSOP Ordering Information NSC Package Drawing Order Number Fault Response Package Type LM25069PMME-1 Latch Off 250 Units on Tape and Reel LM25069PMM-1 Latch Off 1000 Units on Tape and Reel LM25069PMMX-1 Latch Off LM25069PMME-2 Auto Restart LM25069PMM-2 Auto Restart 1000 Units on Tape and Reel LM25069PMMX-2 Auto Restart 3500 Units on Tape and Reel MSOP-10 MUB10A Supplied As 3500 Units on Tape and Reel 250 Units on Tape and Reel Pin Descriptions Pin # Name Description Applications Information 1 SENSE Current sense input The voltage across the current sense resistor (RS) is measured from VIN to this pin. If the voltage across RS reaches 50mV the load current is limited and the fault timer activates. 2 VIN Positive supply input A small ceramic bypass capacitor close to this pin is recommended to suppress transients which occur when the load current is switched off. 3 UVLO/EN Under-voltage lockout An external resistor divider from the system input voltage sets the under-voltage turn-on threshold. An internal 20 A current source provides hysteresis. The enable threshold at the pin is 1.17V. This pin can also be used for remote shutdown control. 4 OVLO Over-voltage lockout An external resistor divider from the system input voltage sets the over-voltage turn-off threshold. An internal 20 A current source provides hysteresis. The disable threshold at the pin is 1.16V. 5 GND Circuit ground 6 TIMER Timing capacitor An external capacitor connected to this pin sets the insertion time delay and the Fault Timeout Period. The capacitor also sets the restart timing of the LM25069-2. 7 PWR Power limit set An external resistor connected to this pin, in conjunction with the current sense resistor (RS), sets the maximum power dissipation allowed in the external series pass MOSFET. 8 PGD Power Good indicator An open drain output. When the external MOSFET VDS decreases below 1.3V, the PGD indicator is active (high). When the external MOSFET VDS increases above 1.9V the PGD indicator switches low. 9 OUT Output feedback Connect to the output rail (external MOSFET source). Internally used to determine the MOSFET VDS voltage for power limiting, and to control the PGD indicator. 10 GATE Gate drive output Connect to the external MOSFET's gate. This pin's voltage is limited at 19.5V above ground. www.national.com 2 LM25069 Absolute Maximum Ratings (Note 1) Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN Supply Voltage +2.9V to 17V PGD Off Voltage 0V to 17V Junction Temp. Range -40C to +85C VIN to GND (Note 5) SENSE, OUT, PGD to GND UVLO to GND OVLO to GND VIN to SENSE ESD Rating (Note 2) Human Body Model Storage Temperature Junction Temperature Lead Temperature (soldering 4 sec) -0.3V to 20V -0.3V to 20V -0.3V to 20V -0.3V to 20V -0.3V to +0.3V 2kV -65C to +150C +150C +260C Electrical Characteristics Limits in standard type are for TJ = 25C only; limits in boldface type apply over the junction temperature (TJ) range of -40C to +85C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 12V. Symbol Parameter Conditions Min. Typ. Max. Units Input (VIN pin) IIN-EN Input Current, enabled UVLO = 2V and OVLO = 0.7V, VIN = 14V 1.6 2.4 mA IIN-DIS Input Current, disabled UVLO = 0.7V or OVLO = 2V 1.0 1.6 mA POR Power On Reset threshold at VIN VIN Increasing 2.6 2.8 POR hysteresis VIN decreasing 150 mV IOUT-EN OUT bias current, enabled OUT = VIN, Normal operation 0.30 A IOUT-DIS OUT bias current, disabled (Note 3) Disabled, OUT = 0V, SENSE = VIN -12 PORHYS V OUT pin UVLO, OVLO pins UVLOTH UVLO threshold 1.154 1.17 1.183 V UVLOHYS UVLO hysteresis current UVLO = 1V UVLODEL UVLO delay Delay to GATE high 15 20 15 26 A Delay to GATE low 8.3 UVLOBIAS UVLO bias current UVLO = 3V s 1 A 1.142 1.16 1.185 V -26 -20 -15 A OVLOTH OVLO threshold OVLOHYS OVLO hysteresis current OVLO = 2V OVLODEL OVLO delay Delay to GATE high 16 Delay to GATE low 8.2 OVLOBIAS OVLO bias current OVLO = 1V s 1 A Power Limit (PWR pin) PWRLIM-1 Power limit sense voltage (VIN-SENSE) SENSE-OUT = 12V, RPWR = 69.8 k PWRLIM-2 IPWR RSAT(PWR) SENSE-OUT = 6V, RPWR = 34.8 k 19 25 31 mV 19 25 31 mV PWR pin current VPWR = 2.5V -15 A PWR pin impedance when disabled UVLO = 0.7V 140 Gate Control (GATE pin) IGATE VGATE Source current Normal Operation -27 -20 -13 A Sink current UVLO = 1V 1.5 2 2.7 mA VIN - SENSE = 150 mV or VIN < POR, VGATE = 5V 160 260 375 mA 18 19.5 21 V Gate output voltage in normal operation GATE voltage with respect to ground 3 www.national.com LM25069 Symbol Parameter Conditions Min. Typ. Max. Units 45 50 55 mV Current Limit VCL Threshold voltage VIN-SENSE voltage tCL Response time VIN-SENSE stepped from 0 mV to 80 mV 15 s SENSE input current Enabled, SENSE = OUT 23 A Disabled, OUT = 0V 12 Enabled, OUT = 0V 62 ISENSE Circuit Breaker VCB Threshold voltage VIN - SENSE tCB Response time VIN - SENSE stepped from 0 mV to 150 mV, time to GATE low, no load 95 110 mV 0.19 0.36 s 1.6 1.72 1.85 V 0.9 1.0 1.1 V 75 Timer (TIMER pin) VTMRH Upper threshold VTMRL Lower threshold ITIMER Restart cycles (LM25069-2) End of 8th cycle (LM25069-2) 0.3 Re-enable Threshold (LM25069-1) 0.3 Insertion time current Sink current, end of insertion time -7.5 TIMER pin = 2V Fault detection current Fault sink current -5.5 V V -3.5 A 1.5 2 2.5 mA -110 -80 -50 A 1.6 2.5 3.4 A DCFAULT Fault Restart Duty Cycle LM25069-2 only 0.67 % tFAULT Fault to GATE low delay TIMER pin reaches the upper threshold 20 s Decreasing 1.3 Threshold Hysteresis 0.6 15 Power Good (PGD pin) PGDTH Threshold measured at SENSE-OUT PGDVOL Output low voltage ISINK = 2 mA PGDIOH Off leakage current VPGD = 17V 1.9 V 30 mV 1 A Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and conditions see the Electrical Characteristics. Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 3: OUT bias current (disabled) due to leakage current through an internal 1.0 M resistance from SENSE to VOUT. Note 4: For detailed information on soldering plastic MSOP packages refer to the Packaging Databook available from National Semiconductor Corporation. Note 5: Current out of a pin is indicated as a negative number. www.national.com 4 Unless otherwise specified the following conditions apply: TJ = 25C, VIN = 12V VIN Pin Input Current vs. VIN SENSE Pin Input Current 30086703 30086704 OUT Pin Input Current GATE Pin Voltage 30086705 30086706 GATE Pin Source Current MOSFET Power Dissipation Limit 30086707 30086709 5 www.national.com LM25069 Typical Performance Characteristics LM25069 PGD Pin Low Voltage vs. Sink Current Input Current, Enabled vs. Temperature 30086708 30086758 UVLO Threshold vs. Temperature UVLO Hysteresis Current vs. Temperature 30086757 30086755 OVLO Threshold vs. Temperature OVLO Hysteresis Current vs. Temperature 30086766 www.national.com 30086756 6 Circuit Breaker Threshold vs. Temperature 30086759 30086760 Power Limit Threshold vs. Temperature GATE Output Voltage vs. Temperature 30086761 30086762 GATE Source Current vs. Temperature PGD Low Voltage vs. Temperature 30086763 30086765 7 www.national.com LM25069 Current Limit Threshold vs. Temperature LM25069 Block Diagram 30086710 30086711 FIGURE 1. Basic Application Circuit www.national.com 8 The LM25069 is designed to control the in-rush current to the load upon insertion of a circuit card into a live backplane or other "hot" power source, thereby limiting the voltage sag on the backplane's supply voltage, and the dV/dt of the voltage applied to the load. Effects on other circuits in the system are minimized, preventing possible unintended resets. A controlled shutdown when the circuit card is removed can also be implemented using the LM25069. In addition to a programmable current limit, the LM25069 monitors and limits the maximum power dissipation in the series pass device to maintain operation within the device Safe Operating Area (SOA). Either current limiting or power limiting for an extended period 30086712 FIGURE 2. LM25069 Application 20 A to charge Q1's gate capacitance. The maximum voltage at the GATE pin is limited by an internal 19.5V zener diode. As the voltage at the OUT pin increases, the LM25069 monitors the drain current and power dissipation of MOSFET Q1. In-rush current limiting and/or power limiting circuits actively control the current delivered to the load. During the in-rush limiting interval (t2 in Figure 3) an internal 80 A fault timer current source charges CT. If Q1's power dissipation and the input current reduce below their respective limiting thresholds before the TIMER pin reaches 1.72V the 80 A current source is switched off, and CT is discharged by the internal 2.5 A current sink (t3 in Figure 3). The in-rush limiting interval is complete when the voltage at the OUT pin increases to within 1.3V of the input voltage (VSYS), and the PGD pin switches high. If the TIMER pin voltage reaches 1.72V before in-rush current limiting or power limiting ceases (during t2), a fault is declared and Q1 is turned off. See the Fault Timer & Restart section for a complete description of the fault mode. Power Up Sequence The VIN operating range of the LM25069 is +2.9V to +17V, with a transient capability to 20V. Referring to the Block Diagram and Figure 1 and Figure 3, as the voltage at VIN initially increases, the external N-channel MOSFET (Q1) is held off by an internal 260 mA pull-down current at the GATE pin. The strong pull-down current at the GATE pin prevents an inadvertent turn-on as the MOSFET's gate-to-drain (Miller) capacitance is charged. Additionally, the TIMER pin is initially held at ground. When the VIN voltage reaches the POR threshold the insertion time begins. During the insertion time, the capacitor at the TIMER pin (CT) is charged by a 5.5 A current source, and Q1 is held off by a 2 mA pull-down current at the GATE pin regardless of the VIN voltage. The insertion time delay allows ringing and transients at VIN to settle before Q1 is enabled. The insertion time ends when the TIMER pin voltage reaches 1.72V. CT is then quickly discharged by an internal 2 mA pull-down current. The GATE pin then switches on Q1 when VSYS exceeds the UVLO threshold. If VSYS is above the UVLO threshold at the end of the insertion time, Q1 switches on at that time. The GATE pin charge pump sources 9 www.national.com LM25069 of time results in the shutdown of the series pass device. In this event, the LM25069-1 latches off until the circuit is reenabled by external control, while the LM25069-2 automatically restarts with defined timing. The circuit breaker function quickly switches off the series pass device upon detection of a severe over-current condition. The Power Good (PGD) output pin indicates when the output voltage is within 1.3V of the system input voltage (VSYS). Programmable under-voltage lock-out (UVLO) and over-voltage lock-out (OVLO) circuits enable the LM25069 when the system input voltage is between the desired thresholds. The typical configuration of a circuit card with LM25069 hot swap protection is shown in Figure 2. Functional Description LM25069 30086713 FIGURE 3. Power Up Sequence (Current Limit only) in the current or power limiting mode the TIMER pin capacitor is charging. If the current and power limiting cease before the TIMER pin reaches 1.72V the TIMER pin capacitor then discharges, and the circuit enters normal operation. If the in-rush limiting condition persists such that the TIMER pin reached 1.72V during t2, the GATE pin is then pulled low by the 2 mA pull-down current. The GATE pin is then held low until either a power up sequence is initiated (LM25069-1), or until the end of the restart sequence (LM25069-2). See the Fault Timer & Restart section. If the system input voltage falls below the UVLO threshold, or rises above the OVLO threshold, the GATE pin is pulled low by the 2 mA pull-down current to switch off Q1. Gate Control A charge pump provides the voltage at the GATE pin to enhance the N-Channel MOSFET's gate. During normal operating conditions (t3 in Figure 3) the gate of Q1 is held charged by an internal 20 A current source. The voltage at the GATE pin (with respect to ground) is limited by an internal 19.5V zener diode. See the graph "GATE Pin voltage. Since the gate-to-source voltage applied to Q1 could be as high as 19.5V during various conditions, a zener diode with the appropriate voltage rating must be added between the GATE and OUT pins if the maximum VGS rating of the selected MOSFET is less than 19.5V. The external zener diode must have a forward current rating of at least 260 mA. When the system voltage is initially applied, the GATE pin is held low by a 260 mA pull-down current. This helps prevent an inadvertent turn-on of the MOSFET through its drain-gate capacitance as the applied system voltage increases. During the insertion time (t1 in Figure 3) the GATE pin is held low by a 2 mA pull-down current. This maintains Q1 in the offstate until the end of t1, regardless of the voltage at VIN or UVLO. Following the insertion time, during t2 in Figure 3, the gate voltage of Q1 is modulated to keep the current or power dissipation level from exceeding the programmed levels. While www.national.com Current Limit The current limit threshold is reached when the voltage across the sense resistor RS (VIN to SENSE) reaches 50 mV. In the current limiting condition, the GATE voltage is controlled to limit the current in MOSFET Q1. While the current limit circuit is active, the fault timer is active as described in the Fault Timer & Restart section. If the load current falls below the current limit threshold before the end of the Fault Timeout Period, the LM25069 resumes normal operation. For proper operation, the RS resistor value should be no larger than 200 10 Fault Timer & Restart When the current limit or power limit threshold is reached during turn-on or as a result of a fault condition, the gate-tosource voltage of Q1 is modulated to regulate the load current and power dissipation in Q1. When either limiting function is activated, an 80 A fault timer current source charges the external capacitor (CT) at the TIMER pin as shown in Figure 5 (Fault Timeout Period). If the fault condition subsides during the Fault Timeout Period before the TIMER pin reaches 1.72V, the LM25069 returns to the normal operating mode and CT is discharged by the 2.5 A current sink. If the TIMER pin reaches 1.72V during the Fault Timeout Period, Q1 is switched off by a 2 mA pull-down current at the GATE pin. The subsequent restart procedure then depends on which version of the LM25069 is in use. The LM25069-1 latches the GATE pin low at the end of the Fault Timeout Period. CT is then discharged to ground by the 2.5 A fault current sink. The GATE pin is held low by the 2 mA pull-down current until a power up sequence is externally initiated by cycling the input voltage (VSYS), or momentarily pulling the UVLO pin below its threshold with an open-collector or open-drain device as shown in Figure 4. The voltage at the TIMER pin must be less than 0.3V for the restart procedure to be effective. Circuit Breaker If the load current increases rapidly (e.g., the load is shortcircuited) the current in the sense resistor (RS) may exceed the current limit threshold before the current limit control loop is able to respond. If the current exceeds approximately twice the current limit threshold (95 mV/RS), Q1 is quickly switched off by the 260 mA pull-down current at the GATE pin, and a Fault Timeout Period begins. When the voltage across RS falls below 95 mV the 260 mA pull-down current at the GATE pin is switched off, and the gate voltage of Q1 is then determined by the current limit or the power limit functions. If the TIMER pin reaches 1.72V before the current limiting or power limiting condition ceases, Q1 is switched off by the 2 mA pulldown current at the GATE pin as described in the Fault Timer & Restart section. Power Limit An important feature of the LM25069 is the MOSFET power limiting. The Power Limit function can be used to maintain the maximum power dissipation of MOSFET Q1 within the device SOA rating. The LM25069 determines the power dissipation in Q1 by monitoring its drain-source voltage (SENSE to OUT), and the drain current through the sense resistor (VIN to SENSE). The product of the current and voltage is compared to the power limit threshold programmed by the resistor at the PWR pin. If the power dissipation reaches the limiting threshold, the GATE voltage is modulated to regulate the current in Q1. While the power limiting circuit is active, the fault timer is active as described in the Fault Timer & Restart section. 30086715 FIGURE 4. Latched Fault Restart Control The LM25069-2 provides an automatic restart sequence which consists of the TIMER pin cycling between 1.72V and 1V seven times after the Fault Timeout Period, as shown in Figure 5. The period of each cycle is determined by the 80 A charging current, and the 2.5 A discharge current, and the value of the capacitor CT. When the TIMER pin reaches 0.3V during the eighth high-to-low ramp, the 20 A current source at the GATE pin turns on Q1. If the fault condition is still present, the Fault Timeout Period and the restart cycle repeat. The Fault Timeout Period during restart cycles is approximately 18% shorter than the initial fault timeout period which initiated the restart cycle. This is due to the fact that the TIMER pin transitions from 0.3V to 1.72V after each restart time, rather than from ground. 11 www.national.com LM25069 m. Higher values may result in instability in the current limit control loop. LM25069 30086716 FIGURE 5. Restart Sequence (LM25069-2) drain device, as shown in Figure 6. Upon releasing the UVLO pin the LM25069 switches on the load current with in-rush current and power limiting. Under-Voltage Lock-Out (UVLO) The series pass MOSFET (Q1) is enabled when the input supply voltage (VSYS) is within the operating range defined by the programmable under-voltage lockout (UVLO) and overvoltage lock-out (OVLO) levels. Typically the UVLO level at VSYS is set with a resistor divider (R1-R3) as shown in Figure 1. Refering to the Block Diagram when VSYS is below the UVLO level, the internal 20 A current source at UVLO is enabled, the current source at OVLO is off, and Q1 is held off by the 2 mA pull-down current at the GATE pin. As VSYS is increased, raising the voltage at UVLO above its threshold the 20 A current source at UVLO is switched off, increasing the voltage at UVLO, providing hysteresis for this threshold. With the UVLO pin above its threshold, Q1 is switched on by the 20 A current source at the GATE pin if the insertion time delay has expired. See the Applications Section for a procedure to calculate the values of the threshold setting resistors (R1-R3). The minimum possible UVLO level at VSYS can be set by connecting the UVLO pin to VIN. In this case Q1 is enabled after the insertion time. 30086717 FIGURE 6. Shutdown Control Power Good Pin The Power Good indicator pin (PGD) is connected to the drain of an internal N-channel MOSFET capable of sustaining 17V in the off-state, and transients up to 20V. An external pull-up resistor is required at PGD to an appropriate voltage to indicate the status to downstream circuitry. The off-state voltage at the PGD pin can be higher or lower than the voltages at VIN and OUT. PGD is switched high when the voltage from SENSE to OUT (the external MOSFET's VDS) decreases below 1.3V. PGD switches low when the MOSFET's VDS is increased past 1.9V. If the UVLO pin is taken below its threshold or the OVLO pin taken above its threshold, to disable the LM25069, PGD switches low within 10 s without waiting for the voltage at OUT to fall. The PGD output pin is high when the voltage at VIN is less than 1.6V. Over-Voltage Lock-Out (OVLO) The series pass MOSFET (Q1) is enabled when the input supply voltage (VSYS) is within the operating range defined by the programmable under-voltage lockout (UVLO) and overvoltage lock-out (OVLO) levels. If VSYS raises the OVLO pin voltage above its threshold Q1 is switched off by the 2 mA pull-down current at the GATE pin, denying power to the load. When the OVLO pin is above its threshold, the internal 20 A current source at OVLO is switched on, raising the voltage at OVLO to provide threshold hysteresis. When VSYS is reduced below the OVLO level Q1 is enabled. See the Applications Section for a procedure to calculate the threshold setting resistor values. Shutdown Control The load current can be remotely switched off by taking the UVLO pin below its threshold with an open collector or open www.national.com 12 CURRENT LIMIT, RS The LM25069 monitors the current in the external MOSFET (Q1) by measuring the voltage across the sense resistor (RS), connected from VIN to SENSE. The required resistor value is calculated from: (1) where ILIM is the desired current limit threshold. If the voltage across RS reaches 50 mV, the current limit circuit modulates the gate of Q1 to regulate the current at ILIM. While the current limiting circuit is active, the fault timer is active as described 30086719 FIGURE 7. Sense Resistor Connections The accuracy of the power limit function at turn-on may degrade if a very low value power dissipation limit is set. The reason for this caution is that the voltage across the sense resistor, which is monitored and regulated by the power limit circuit, is lowest at turn-on when the regulated current is at minimum. The voltage across the sense resistor during power limit can be expressed as follows: POWER LIMIT THRESHOLD The LM25069 determines the power dissipation in the external MOSFET (Q1) by monitoring the drain current (the current in RS), and the VDS of Q1 (SENSE to OUT pins). The resistor at the PWR pin (RPWR) sets the maximum power dissipation for Q1, and is calculated from the following equation: RPWR = 2.32 x 105 x RS x PFET(LIM) (2) where PFET(LIM) is the desired power limit threshold for Q1, and RS is the current sense resistor described in the Current Limit section. For example, if RS is 10 m , and the desired power limit threshold is 20W, RPWR calculates to 46.4 k. If Q1's power dissipation reaches the threshold Q1's gate is modulated to regulate the load current, keeping Q1's power from exceeding the threshold. For proper operation of the power limiting feature, RPWR must be 150 k. While the power limiting circuit is active, the fault timer is active as described in the Fault Timer & Restart section. Typically, power limit is reached during startup, or if the output voltage falls due to a severe overload or short circuit. The programmed maximum power dissipation should have a reasonable margin from the maximum power defined by the FET's SOA chart if the LM25069-2 is used since the FET will be repeatedly stressed during fault restart cycles. The FET manufacturer should be consulted for guidelines. If the application does not require use of the power limit function the PWR pin can be left open. where IL is the current in RS, and VDS is the voltage across Q1. For example, if the power limit is set at 20W with RS = 10 mohms, and VDS = 15V the sense resistor voltage calculates to 13.3 mV, which is comfortably regulated by the LM25069. However, if a lower power limit is set lower (e.g., 2W), the sense resistor voltage calculates to 1.33 mV. At this low level noise and offsets within the LM25069 may degrade the power limit accuracy. To maintain accuracy, the sense resistor voltage should not be less than 5 mV. TURN-ON TIME The output turn-on time depends on whether the LM25069 operates in current limit, or in both power limit and current limit, during turn-on. 13 www.national.com LM25069 in the Fault Timer & Restart section. For proper operation, RS must be no larger than 200 m. While the maximum load current in normal operation can be used to determine the required power rating for resistor RS, basing it on the current limit value provides a more reliable design since the circuit can operate near the current limit threshold continuously. The resistor's surge capability must also be considered since the circuit breaker threshold is approximately twice the current limit threshold. Connections from RS to the LM25069 should be made using Kelvin techniques. In the suggested layout of Figure 7 the small pads at the lower corners of the sense resistor connect only to the sense resistor terminals, and not to the traces carrying the high current. With this technique, only the voltage across the sense resistor is applied to VIN and SENSE, eliminating the voltage drop across the high current solder connections. Application Information (Refer to Figure 1) LM25069 A) Turn-on with current limit only: The current limit threshold (ILIM) is determined by the current sense resistor (RS). If the current limit threshold is less than the current defined by the power limit threshold at maximum VDS the circuit operates at the current limit threshold only during turn-on. Referring to Figure 10a, as the load current reaches ILIM, the gate-tosource voltage is controlled at VGSL to maintain the current at ILIM. As the output voltage reaches its final value, (VDS 0V) the drain current reduces to its normal operating value. The time for the OUT pin voltage to transition from zero volts to VSYS is equal to: 30086723 FIGURE 9. Load Draws Current During Turn-On where CL is the load capacitance. For example, if VSYS = 12V, CL = 1000 F, and ILIM = 1A, tON calculates to 12 ms. The maximum instantaneous power dissipated in the MOSFET is 12W. This calculation assumes the time from t1 to t2 in Figure 10a is small compared to tON, and the load does not draw any current until after the output voltage has reached its final value, and PGD switches high (Figure 8). If the load draws current during the turn-on sequence (Figure 9), the turn-on time is longer than the above calculation, and is approximately equal to: B) Turn-on with power limit and current limit: The maximum allowed power dissipation in Q1 (PFET(LIM)) is defined by the resistor at the PWR pin, and the current sense resistor RS. See the Power Limit Threshold section. If the current limit threshold (ILIM) is higher than the current defined by the power limit threshold at maximum VDS (PFET(LIM)/VSYS) the circuit operates initially in the power limit mode when the VDS of Q1 is high, and then transitions to current limit mode as the current increases to ILIM and VDS decreases. See Figure 10b. Assuming the load (RL) is not connected during turn-on, the time for the output voltage to reach its final value is approximately equal to: where RL is the load resistance. The Fault Timeout Period must be set longer than tON to prevent a fault shutdown before the turn-on sequence is complete. For example, if VSYS = 12V, CL = 1000 F, ILIM = 1A, and PFET(LIM) = 10W, tON calculates to 12.2 ms, and the initial current level (IP) is approximately 0.83A. The Fault Timeout Period must be set longer than tON. 30086722 FIGURE 8. No Load Current During Turn-On www.national.com 14 LM25069 30086725 FIGURE 10. MOSFET Power Up Waveforms must be at least 260 mA to conduct the GATE pull-down current when a circuit breaker condition is detected. MOSFET SELECTION It is recommended that the external MOSFET (Q1) selection be based on the following criteria: - The BVDSS rating should be greater than the maximum system voltage (VSYS), plus ringing and transients which can occur at VSYS when the circuit card, or adjacent cards, are inserted or removed. - The maximum continuous current rating should be based on the current limit threshold (50 mV/RS), not the maximum load current, since the circuit can operate near the current limit threshold continuously. - The Pulsed Drain Current spec (IDM) must be greater than the current threshold for the circuit breaker function (95 mV/ RS). - The SOA (Safe Operating Area) chart of the device, and the thermal properties, should be used to determine the maximum power dissipation threshold set by the RPWR resistor. The programmed maximum power dissipation should have a reasonable margin from the maximum power defined by the FET's SOA chart if the LM25069-2 is used since the FET will be repeatedly stressed during fault restart cycles. The FET manufacturer should be consulted for guidelines. - RDS(on) should be sufficiently low that the power dissipation at maximum load current (IL(max)2 x RDS(on)) does not raise its junction temperature above the manufacturer's recommendation. If the circuit's input voltage is at the low end of the LM25069's operating range (<3.5V), or at the high end of the operating range (>14V), the gate-to-source voltage applied to the MOSFET by the LM25069 is less than 5V, and can approach 1V in a worst case situation. See the graph "GATE Pin Voltage". The selected device must have a suitable Gate-to-Source Threshold Voltage. The gate-to-source voltage provided by the LM25069 can be as high as 19.5V at turn-on when the output voltage is zero. At turn-off the reverse gate-to-source voltage will be equal to the output voltage at the instant the GATE pin is pulled low. If the device chosen for Q1 is not rated for these voltages, an external zener diode must be added from its gate to source, with the zener voltage less than the device maximum VGS rating. The zener diode's working voltage protects the MOSFET during turn-on, and its forward voltage protects the MOSFET during shutoff. The zener diode's forward current rating TIMER CAPACITOR, CT The TIMER pin capacitor (CT) sets the timing for the insertion time delay, fault timeout period, and restart timing of the LM25069-2. A) Insertion Delay - Upon applying the system voltage (VSYS) to the circuit, the external MOSFET (Q1) is held off during the insertion time (t1 in Figure 3) to allow ringing and transients at VSYS to settle. Since each backplane's response to a circuit card plug-in is unique, the worst case settling time must be determined for each application. The insertion time starts when VIN reaches the POR threshold, at which time the internal 5.5 A current source charges CT from 0V to 1.72V. The required capacitor value is calculated from: For example, if the desired insertion delay is 250 ms, CT calculates to 0.8 F. At the end of the insertion delay, CT is quickly discharged by a 2 mA current sink. B) Fault Timeout Period - During in-rush current limiting or upon detection of a fault condition where the current limit and/ or power limit circuits regulate the current through Q1, the fault timer current source (80 A) switches on to charge CT. The Fault Timeout Period is the time required for the voltage at the TIMER pin to transition from ground to 1.72V, at which time Q1 is switched off. If the LM25069-1 is in use, the required capacitor value is calculated from: (3) For example, if the desired Fault Timeout Period is 17 ms, CT calculates to 0.8 F. When the Fault Timeout Period expires, the LM25069-1 latches the GATE pin low until a powerup sequence is initiated by external circuitry. If the LM25069-2 is in use, the Fault Timeout Period during restart cycles is approximately 18% shorter than the initial fault timeout period which initiated the restart cycles since the voltage at the TIMER pin transitions from 0.3V to 1.72V. Since the Fault Timeout Period must always be longer than the turn-on-time, 15 www.national.com LM25069 - The lower OVLO threshold (VOVL) cannot be chosen in advance in this case, but is determined after the values for R1-R3 are determined. If VOVL must be accurately defined in addition to the other three thresholds, see Option B below. The resistors are calculated as follows: the required capacitor value for the LM25069-2 is calculated using this shorter time period: (4) For example, if the desired Fault Timeout Period is 17 ms, CT calculates to 0.96 F. When the Fault Timeout Period of the LM25069-2 expires, a restart sequence starts as described below (Restart Timiing). Since the LM25069 normally operates in power limit and/or current limit during a power-up sequence, the Fault Timeout Period MUST be longer than the time required for the output voltage to reach its final value. See the Turn-on Time section C) Restart Timing For the LM25069-2, after the Fault Timeout Period described above, CT is discharged by the 2.5 A current sink to 1.0V. The TIMER pin then cycles through seven additional charge/discharge cycles between 1V and 1.72V as shown in Figure 5. The restart time ends when the TIMER pin voltage reaches 0.3V during the final high-to-low ramp. The restart time, after the Fault Timeout Period, is equal to: The lower OVLO threshold is calculated from: As an example, assume the application requires the following thresholds: VUVH = 8V, VUVL = 7V, VOVH = 15V. = CT x 2.65 x 106 For example, if CT = 0.8 F, tRESTART = 2.12 seconds. At the end of the restart time, Q1 is switched on. If the fault is still present, the fault timeout and restart sequence repeats. The on-time duty cycle of Q1 is approximately 0.67% in this mode. UVLO, OVLO By programming the UVLO and OVLO thresholds the LM25069 enables the series pass device (Q1) when the input supply voltage (VSYS) is within the desired operational range. If VSYS is below the UVLO threshold, or above the OVLO threshold, Q1 is switched off, denying power to the load. Hysteresis is provided for each threshold. Option A: The configuration shown in Figure 11 requires three resistors (R1-R3) to set the thresholds. The lower OVLO threshold calculates to 13.9V, and the OVLO hysteresis is 1.1V. Note that the OVLO hysteresis is always slightly greater than the UVLO hysteresis in this configuration. When the R1-R3 resistor values are known, the threshold voltages and hysteresis are calculated from the following: VUV(HYS) = R1 x 20 A 30086729 FIGURE 11. UVLO and OVLO Thresholds Set By R1-R3 VOV(HYS) = (R1 + R2) x 20 A The procedure to calculate the resistor values is as follows: - Choose the upper UVLO threshold (VUVH), and the lower UVLO threshold (VUVL). - Choose the upper OVLO threshold (VOVH). www.national.com Option B: If all four thresholds must be accurately defined, the configuration in Figure 12 can be used. 16 30086741 FIGURE 12. Programming the Four Thresholds VUV(HYS) = R1 x 20 A The four resistor values are calculated as follows: - Choose the upper and lower UVLO thresholds (VUVH) and (VUVL). VOV(HYS) = R3 x 20 A Option C: The minimum UVLO level is obtained by connecting the UVLO pin to VIN as shown in Figure 13. Q1 is switched on when the VIN voltage reaches the POR threshold (2.6V). The OVLO thresholds are set using R3, R4. Their values are calculated using the procedure in Option B. -Choose the upper and lower OVLO threshold (VOVH) and (VOVL). 30086750 FIGURE 13. UVLO = POR with Shutdown/Restart Control Option D: The OVLO function can be disabled by grounding the OVLO pin. The UVLO thresholds are set as described in Option B or Option C. POWER GOOD PIN During turn-on, the Power Good pin (PGD) is high until the voltage at VIN increases above 1.6V. PGD then switches low, remaining low as the VIN voltage increases. When the voltage at OUT increases to within 1.3V of the SENSE pin (VDS <1.3V), PGD switches high. PGD switches low if the 17 www.national.com LM25069 As an example, assume the application requires the following thresholds: VUVH = 8V, VUVL = 7V, VOVH = 15.5V, and VOVL = 14V. Therefore VUV(HYS) = 1V, and VOV(HYS) = 1.5V. The resistor values are: R1 = 50 k, R2 = 10 k R3 = 75 k, R4 = 6.07 k Where the R1-R4 resistor values are known, the threshold voltages and hysteresis are calculated from the following: LM25069 If a delay is required at PGD, suggested circuits are shown in Figure 15. In Figure 15a, capacitor CPG adds delay to the rising edge, but not to the falling edge. In Figure 15b, the rising edge is delayed by RPG1 + RPG2 and CPG, while the falling edge is delayed a lesser amount by RPG2 and CPG. Adding a diode across RPG2 (Figure 15c) allows for equal delays at the two edges, or a short delay at the rising edge and a long delay at the falling edge. VDS of Q1 increases above 1.9V. A pull-up resistor is required at PGD as shown in Figure 14. The pull-up voltage (VPGD) can be as high as 17V, and can be higher or lower than the voltages at VIN and OUT. 30086751 FIGURE 14. Power Good Output 30086752 FIGURE 15. Adding Delay to the Power Good Output Pin Design-in Procedure PC Board Guidelines The recommended design-in procedure is as follows: * Determine the current limit threshold (ILIM). This threshold must be higher than the normal maximum load current, allowing for tolerances in the current sense resistor value and the LM25069 Current Limit threshold voltage. Use equation 1 to determine the value for RS. * Determine the maximum allowable power dissipation for the series pass FET (Q1), using the device's SOA information. Use equation 2 to determine the value for RPWR. * Determine the value for the timing capacitor at the TIMER pin (CT) using equation 3 or equation 4. The fault timeout period (tFAULT) must be longer than the circuit's turn-ontime. The turn-on time can be estimated using the equations in the TURN-ON TIME section of this data sheet, but should be verified experimentally. Review the resulting insertion time, and restart timing if the LM25069-2 is used. * Choose option A, B, C, or D from the UVLO, OVLO section of the Application Information for setting the UVLO and OVLO thresholds and hysteresis. Use the procedure for the appropriate option to determine the resistor values at the UVLO and OVLO pins. * Choose the appropriate voltage, and pull-up resistor, for the Power Good output. The following guidelines should be followed when designing the PC board for the LM25069: * Place the LM25069 close to the board's input connector to minimize trace inductance from the connector to the FET. * Place a small capacitor (1000 pF) directly adjacent to the VIN and GND pins of the LM25069 to help minimize transients which may occur on the input supply line. Transients of several volts can easily occur when the load current is shut off. * The sense resistor (RS) should be close to the LM25069, and connected to it using the Kelvin techniques shown in Figure 7. * The high current path from the board's input to the load (via Q1), and the return path, should be parallel and close to each other to minimize loop inductance. * The ground connection for the various components around the LM25069 should be connected directly to each other, and to the LM25069's GND pin, and then connected to the system ground at one point. Do not connect the various component grounds to each other through the high current ground line. * Provide adequate heat sinking for the series pass device (Q1) to help reduce stresses during turn-on and turn-off. * The board's edge connector can be designed to shut off the LM25069 as the board is removed, before the supply www.national.com 18 connector pin. When the board is inserted into the edge connector, the system voltage is applied to the LM25069's VIN pin before the UVLO voltage is taken high. 30086753 FIGURE 16. Recommended Board Connector Design 19 www.national.com LM25069 voltage is disconnected from the LM25069. In Figure 16 the voltage at the UVLO pin goes to ground before VSYS is removed from the LM25069 due to the shorter edge LM25069 B) If the load powered by the LM25069 hot swap circuit has inductive characteristics, a Schottky diode is required across the LM25069's output, along with some load capacitance. The capacitance and the diode are necessary to limit the negative excursion at the OUT pin when the load current is shut off. If the OUT pin transitions more than 0.3V negative the LM25069 will internally reset, interfering with the latch-off feature of the LM25069-1, or the restart cycle of the LM25069-2. See Figure 17. System Considerations A) Continued proper operation of the LM25069 hot swap circuit requires capacitance be present on the supply side of the connector into which the hot swap circuit is plugged in, as depicted in Figure 2. The capacitor in the "Live Power Source" section is necessary to absorb the transient generated whenever the hot swap circuit shuts off the load current. If the capacitance is not present, inductance in the supply lines will generate a voltage transient at shut-off which can exceed the absolute maximum rating of the LM25069, resulting in its destruction. 30086754 FIGURE 17. Output Diode Required for Inductive Loads www.national.com 20 LM25069 Physical Dimensions inches (millimeters) unless otherwise noted NS Package Number MUB10A 21 www.national.com LM25069 Positive Low Voltage Power Limiting Hot Swap Controller Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated