1
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series
Rated Voltage Range 2.5 ~ 35VDC
Capacitance Range 10 ~ 1,200μF
Operating Temperature Range -55°C ~ +105°C
Capacitance Tolerance ±20% (M)
Maximum Leakage Current
After 2 minutes
2.5V ~ 20V = 0.2CV
25V ~ 35V = 0.5CV
Max. Tan δ at 120Hz/20°C
W.V. (Vdc) 2.5 4.0 6.3 10 16 20 25 35
S.V. (Vdc) 2.9 4.6 7.2 11.5 18 23 28.7 40
Tan δ0.12 max.
Low Temperature Stability
Impedance Ratio @ 120Hz
Z-55°C/Z+20°C <1.15
Z+105°C/Z+20°C <1.25
Load Life Test
@ 105°C
Duration All Case Sizes: 2,000 hours
Δ Capacitance Within ±20% of initial measured value
Δ Tan δLess than 150% of specifi ed value
Δ ESR Less than 150% of specifi ed value
Δ LC Less than specifi ed value
Damp Heat
The following specifi cations shall be satisfi ed when the capacitors are restored to +20°C after
subjecting them to the DC rated voltage at +60°C, 90% ~ 95% RH for 500 hours.
Appearance No signifi cant damage
Δ Capacitance Within ±20% of initial measured value
Δ Tan δLess than 150% of specifi ed value
Δ ESR Less than 150% of specifi ed value
Δ LC Less than specifi ed value
Surge Voltage
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the specifi ed surge
voltage @ +105°C for 30 seconds through a protective resistor (1K ohm) and discharged for 5 minutes,
30 seconds.
Appearance No signifi cant damage
Δ Capacitance Within ±20% of initial measured value
Δ Tan δLess than 150% of specifi ed value
Δ ESR Less than 150% of specifi ed value
Δ LC Less than specifi ed value
Failure Rate 0.5% per 1,000 hours maximum (Confi dence level 60% @ +105°C)
SUPER LOW ESR, WIDE TEMPERATURE, SURFACE MOUNT, POLARIZED
FEATURES
• ULTRA LOW ESR (TO 13mΩ)
• HIGH RIPPLE CURRENT RATINGS
• REDUCED SIZES (LOW PROFILE)
CHARACTERISTICS
PRECAUTIONS
Please review the notes on correct use, safety and precautions found on
pages T10 & T11 of NIC’s Electrolytic Capacitor catalog.
Also found at www.niccomp.com/precautions
If in doubt or uncertainty, please review your specifi c application - process
details with NIC’s technical support personnel: tpmg@niccomp.com
* NEW *
Low ESR &
High Ripple Current
NSPVM 391 M 2.5V 6.3X6 L LB F .
RoHS Compliant
Sn-Bi Finish, 15" Reel
Peak Refl ow Temperature: L = +250°C, J = +240°C
Case Size (DφxL)
Working Voltage (Vdc)
Tolerance Code (M=20%)
Capacitance Code: First 2 characters
signifi cant, third character is multiplier
Series
PART NUMBER SYSTEM PEAK REFLOW SOLDERING CODE
Code Peak Refl ow Temperature
L +250°C
J +240°C
TERMINATION/PACKAGING CODE
Code Termination Finish and Reel Size
LB Sn-Bi Finish, 15" reel
2NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
STANDARD PRODUCT AND CASE SIZE TABLE DφxL (mm)
Part Number Cap.
(μF)
Voltage
(VDC)
Case Size
(DxL)
Leakage Current
(μA) after 2 minutes
Max. ESR (mΩ)
+20°C/100KHz
Ripple Current Rating
(mA) +105°C/100KHz
Load Life Hours
@+105°C
NSPVM181M2.5V5X6LLBF 180
2.5
5X6 90 21 2670 2,000
NSPVM391M2.5V6.3X6LLBF 390 6.3X6 195 15 3160 2,000
NSPVM561M2.5V8X7JLBF 560 8X7 280 13 3600 2,000
NSPVM681M2.5V8X7JLBF 680 8X7 340 13 3600 2,000
NSPVM122M2.5V10X8JLBF 1200 10X8 600 13 4450 2,000
NSPVM101M4V5X6LLBF 100
4.0
5X6 80 22 2160 2,000
NSPVM151M4V5X6LLBF 150 5X6 120 22 2610 2,000
NSPVM271M4V6.3X6LLBF 270 6.3X6 216 15 3160 2,000
NSPVM331M4V6.3X6LLBF 330 6.3X6 264 15 3160 2,000
NSPVM471M4V8X7JLBF 470 8X7 376 14 3950 2,000
NSPVM561M4V8X7JLBF 560 8X7 448 14 3950 2,000
NSPVM102M4V10X8JLBF 1000 10X8 800 14 4300 2,000
NSPVM101M6.3V5X6LLBF 100
6.3
5X6 126 24 2500 2,000
NSPVM121M6.3V5X6LLBF 120 5X6 151 24 2500 2,000
NSPVM221M6.3V6.3X6LLBF 220 6.3X6 277 15 3160 2,000
NSPVM331M6.3V8X7JLBF 330 8X7 415 14 3950 2,000
NSPVM391M6.3V8X7JLBF 390 8X7 491 14 3950 2,000
NSPVM821M6.3V10X8JLBF 820 10X8 1033 14 4300 2,000
NSPVM470M10V5X6LLBF 47
10
5X6 94 28 2310 2,000
NSPVM560M10V5X6LLBF 56 5X6 112 28 2310 2,000
NSPVM680M10V5X6LLBF 68 5X6 136 28 2310 2,000
NSPVM121M10V6.3X6LLBF 120 6.3X6 240 25 2530 2,000
NSPVM221M10V8X7JLBF 220 8X7 440 21 3220 2,000
NSPVM271M10V8X7JLBF 270 8X7 540 21 3220 2,000
NSPVM471M10V10X8JLBF 470 10X8 940 19 3800 2,000
NSPVM330M16V5X6LLBF 33
16
5X6 105 35 2070 2,000
NSPVM390M16V5X6LLBF 39 5X6 124 35 2070 2,000
NSPVM680M16V6.3X6LLBF 68 6.3X6 217 28 2340 2,000
NSPVM101M16V8X7JLBF 100 8X7 320 24 3010 2,000
NSPVM121M16V8X7JLBF 120 8X7 384 24 3010 2,000
NSPVM221M16V10X8JLBF 220 10X8 704 22 3450 2,000
NSPVM220M20V6.3X6LLBF 22
20
6.3X6 88 50 1650 2,000
NSPVM470M20V8X7JLBF 47 8X7 188 45 2000 2,000
NSPVM820M20V10X8JLBF 82 10X8 328 40 2500 2,000
NSPVM100M25V6.3X6LLBF 10
25
6.3X6 125 60 1500 2,000
NSPVM220M25V8X7JLBF 22 8X7 275 50 1800 2,000
NSPVM390M25V10X8JLBF 39 10X8 488 45 2100 2,000
NSPVM150M35V8X7JLBF 15 35 8X7 263 150 1000 2,000
NSPVM330M35V10X8JLBF 33 10X8 578 100 1800 2,000
Frequency (Hz) 100 1K 10K >100K
10μF ~ 1,200μF 0.10 0.45 0.50 1.0
RIPPLE CURRENT FREQUENCY CORRECTION FACTORS
Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series
M2E
390
2.5V
MARKING Date Code
2 = year 2012
E = month (A-Jan, B-Feb, C-March, D-April, E-May, etc.)
Capacitance
Voltage
Series
DIMENSIONS (mm)
0.3mm max.
Dφ
L
Case Size Dφ ±0.5 L max. A, B ±0.2 W I ref P ref
5X6 5.0 6.0 5.3 0.5 ~ 0.8 2.3 1.5
6.3X6 6.3 6.0 6.6 0.5 ~ 0.8 2.7 2.0
8X7 8.0 7.0 8.4 0.5 ~ 0.8 3.0 3.1
10X8 10 8.0 10.4 0.7 ~ 1.1 3.3 4.7
+ -
II
W
P
A
B
3
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
SPECIFICATIONS ARE SUBJECT TO CHANGE
Solid Polymer Aluminum Electrolytic Capacitors NSPVM Series
+ -
AA
B
C
RECOMMENDED LAND PATTERN DIMENSIONS (mm)
Case Size A B C
5X6 3.0 1.6 1.4
6.3X6 3.6 1.6 1.9
8X7 4.0 1.6 2.1
10X8 4.0 2.5 4.0
Diameter Preheat
(120 sec. max.)
Time above
200°C
Time above
230°C
Peak
Temperature
Number
of Refl ow Passes1
5 ~ 6.3mm 160°C ~ 190°C 70 sec. max. 50 sec. max. 240°C/5 sec. 2x
60 sec. max. 40 sec. max. 250°C/5 sec. 2x
8 ~ 10mm 160°C ~ 190°C 70 sec. max. 50 sec. max. 230°C/5 sec. 2x
60 sec. max. 40 sec. max. 240°C/5 sec. 2x
SOLDERING TEMPERATURES AND DURATIONS
1. Two refl ow passes are permissible with a cool down to room temperature required between the fi rst
and second pass (more than 1 hour).
2. Some case swelling may occur (~ 0.3mm) which is not an indication that the capacitor performance
has been compromised.
RECOMMENDED REFLOW SOLDERING PROFILE
Time Above 200°C
(see table above)
50
100
150
200
Time (Seconds)
Temperature - Deg. C
Preheat - 120 seconds max.
(see table for temperature)
Peak Temperature
(see table above)
250
230 Time Above 230°C
(see table above)
T
APFeeding
+
-
1.5∅ +0.1/- 1.75 ±
D
B
C
1.5φ+0.1/-0 1.75 + 0.15
t
4 + 0.1
Case Size A
±0.5
B
±0.5
C
±0.3
D
±0.1
P
±0.1
T
±0.2
t
max.
5X6 5.7 5.7 12.0 5.5 12.0 6.2 0.4
6.3X6 7.0 7.0 16.0 7.5 12.0 6.2 0.4
8X7 8.7 8.7 24.0 11.5 12.0 7.2 0.4
10X8 10.7 10.7 24.0 11.5 16.0 8.2 0.4
Case Size W
±1.0
Qty per Reel
15" (380mm)
5X6 14.0 1,000
6.3X6 18.0 1,000
8X7 26.0 1,000
10X8 26.0 500
REEL DIMENSIONS (mm)
TAPING SPECIFICATIONS (mm)
1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets.
2. Leader tape: Approximately 20cm of cover tape at leader.
3. Connection: Maximum 3 connections (slices) per reel.
2mm ± 0.5mm
φ13mm ± 0.5mm
φ21mm ± 0.8mm
φ380mm ± 2.0mm
φ50mm min.
W
CARRIER DIMENSIONS (mm)
