MAX3221E/ LE AVAILAB MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown General Description Next Generation Device Features The MAX3221E/MAX3223E/MAX3243E are 3V-powered EIA/TIA-232 and V.28/V.24 communications interfaces with automatic shutdown/wakeup features, high datarate capabilities, and enhanced electrostatic discharge (ESD) protection. All transmitter outputs and receiver inputs are protected to 15kV using IEC 1000-4-2 AirGap Discharge, to 8kV using IEC 1000-4-2 Contact Discharge, and to 15kV using the Human Body Model. The MAX3221E/MAX3223E/MAX3243E achieve a 1A supply current with Maxim's revolutionary AutoShutdownTM feature. They save power without changes to the existing BIOS or operating system by entering low-power shutdown mode when the RS-232 cable is disconnected, or when the transmitters of the connected peripherals are off. o For Space-Constrained Applications: MAX3228E/MAX3229E: 15kV ESD-Protected, +2.5V to +5.5V RS-232 Transceivers in UCSPTM MAX3222E/MAX3232E/MAX3237E/MAX3241E/ MAX3246E: 15kV ESD-Protected Down to 10nA, +3.0V to +5.5V, Up to 1Mbps, True RS-232 Transceivers (MAX3246E Available in a UCSP Package) The transceivers have a proprietary low-dropout transmitter output stage, delivering true RS-232 performance from a +3.0V to +5.5V supply with a dual charge pump. The charge pump requires only four small 0.1F capacitors for operation from a +3.3V supply. Each device is guaranteed to run at data rates of 250kbps while maintaining RS-232 output levels. The MAX3221E contains just one driver and one receiver, making it the smallest single-supply RS-232 transceiver. The MAX3223E has two drivers and two receivers. The MAX3243E is a complete 3-driver/5-receiver serial port ideal for notebook or subnotebook computers. It also includes two noninverting receiver outputs that are always active, allowing external devices to be monitored without Functional Diagrams forward biasing the protection diodes in circuitry that may be powered down. The MAX3221E, MAX3223E, and MAX3243E are available in space-saving TQFN, SSOP, and TSSOP packages. Applications Notebook, Subnotebook, and Palmtop Computers Cellular Phones Battery-Powered Equipment Handheld Equipment Peripherals Printers o For Data Cable Applications: MAX3380E/MAX3381E: +2.35V to +5.5V, 1A, 2Tx/2Rx RS-232 Transceivers with 15kV ESDProtected I/O and Logic Pins Ordering Information PART PIN-PACKAGE MAX3221ECTE+ 0C to +70C 16 TQFN-EP* MAX3221ECUE+ 0C to +70C 16 TSSOP MAX3221ECAE+ 0C to +70C 16 SSOP MAX3221EEAE+ -40C to +85C 16 SSOP MAX3221EETE+ -40C to +85C 16 TQFN-EP* MAX3221EEUE+ -40C to +85C MAX3223ECPP+ 0C to +70C 20 PDIP MAX3223ECAP+ 0C to +70C 20 SSOP MAX3223ECUP+ 0C to +70C 20 TSSOP MAX3223ECTP+ 0C to +70C MAX3223EEPP+ -40C to +85C 20 PDIP MAX3223EEAP+ -40C to +85C 20 SSOP MAX3223EEUP+ -40C to +85C 20 TSSOP MAX3223EETP+ -40C to +85C 20 TQFN-EP* 16 TSSOP 20 TQFN-EP* MAX3223EEUP/V+ -40C to +85C 20 TSSOP *Exposed pad. +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. Ordering Information continued at end of data sheet. Selector Guide PART MAX3221E Pin Configurations appear at end of data sheet. TEMP RANGE NO. OF DRIVERS/ RECEIVERS VCC RANGE (V) AutoShutdown 1/1 +3.0 to +5.5 Typical Operating Circuits appear at end of data sheet. Pin Configurations appear at end of data sheet. MAX3243E 3/5 +3.0 to +5.5 Functional Diagrams continued at end of data sheet. AutoShutdown and UCSP are trademarks of Maxim Integrated Products, Inc. UCSP is a trademark of Maxim Integrated Products, Inc. Covered by U.S. Patent numbers 4,636,930; 4,679,134; 4,777,577; 4,797,899; 4,809,152; 4,897,774; 4,999,761; 5,649,210; and other patents pending. MAX3223E 2/2 +3.0 to +5.5 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maximintegrated.com. 19-1283; Rev 7; 8/11 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown ABSOLUTE MAXIMUM RATINGS VCC to GND ..............................................................-0.3V to +6V V+ to GND (Note 1) ..................................................-0.3V to +7V V- to GND (Note 1) ...................................................+0.3V to -7V V+ + |V-| (Note 1) .................................................................+13V Input Voltages T_IN, EN, FORCEON, FORCEOFF to GND ............-0.3V to +6V R_IN to GND ......................................................................25V Output Voltages T_OUT to GND................................................................13.2V R_OUT, R2OUTB, INVALID to GND .........-0.3V to (VCC + 0.3V) Short-Circuit Duration T_OUT to GND .........................................................Continuous Continuous Power Dissipation (TA = +70C) 16-Pin SSOP (derate 7.14mW/C above +70C) ...........571mW 16-Pin TSSOP (derate 9.4mW/C above +70C) ........754.7mW 16-Pin TQFN (derate 20.8mW/C above +70C) ......1666.7mW 20-Pin Plastic DIP (derate 11.11mW/C above +70C)....889mW 20-Pin SSOP (derate 8.00mW/C above +70C) ...........640mW 20-Pin TSSOP (derate 10.9mW/C above +70C) .........879mW 20-Pin TQFN (derate 21.3mW/C above +70C) ......1702.1mW 28-Pin SSOP (derate 9.52mW/C above +70C)............762mW 28-Pin TSSOP (derate 12.8mW/C above +70C) .......1026mW 32-Pin TQFN (derate 37mW/C above +70C) ............2963mW Operating Temperature Ranges MAX32_ _EC_ _ ....................................................0C to +70C MAX32_ _EE_ _..................................................-40C to +85C Storage Temperature Range .............................-65C to +160C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Note 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +3.0V to +5.5V, C1-C4 = 0.1F (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC CHARACTERISTICS (VCC = 3.3V or 5.0V, TA = +25C) Supply Current, AutoShutdown FORCEON = GND, FORCEOFF = VCC, all R_IN open 1.0 10 A Supply Current, Shutdown FORCEOFF = GND, all R_IN = GND 1.0 10 A Supply Current, AutoShutdown Disabled FORCEON = FORCEOFF = VCC, no load 0.3 1 mA 0.8 V LOGIC INPUTS Input Logic Threshold Low T_IN, EN, FORCEON, FORCEOFF Input Logic Threshold High T_IN, EN, FORCEON, FORCEOFF VCC = 3.3V 2.0 VCC = 5.0V 2.4 Transmitter Input Hysteresis V 0.5 V T_IN, EN, FORCEON, FORCEOFF 0.01 1 A Output Leakage Current R_OUT receivers disabled 0.05 10 A Output Voltage Low IOUT = 1.6mA 0.4 V Output Voltage High IOUT = -1.0mA Input Leakage Current RECEIVER OUTPUTS VCC - 0.6 VCC - 0.1 V AutoShutdown (FORCEON = GND, FORCEOFF = VCC) 2 Receiver Input Threshold to INVALID Output High Figure 5a Receiver Input Threshold to INVALID Output Low Figure 5a INVALID Output Voltage Low IOUT = 1.6mA INVALID Output Voltage High IOUT = -1.0mA Positive threshold Negative threshold 2.7 -2.7 -0.3 VCC - 0.6 V 0.3 V 0.4 V V Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown ELECTRICAL CHARACTERISTICS (continued) (VCC = +3.0V to +5.5V, C1-C4 = 0.1F (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Receiver Positive or Negative Threshold to INVALID High tINVH VCC = 5V, Figure 5b 1 s Receiver Positive or Negative Threshold to INVALID Low tINVL VCC = 5V, Figure 5b 30 s Receiver or Transmitter Edge to Transmitters Enabled tWU VCC = 5V, Figure 5b 100 s RECEIVER INPUTS Input Voltage Range -25 Input Voltage Range -25 Input Threshold Low TA = +25C Input Threshold High TA = +25C VCC = 3.3V 0.6 1.2 VCC = 5.0V 0.8 1.5 25 V 25 V V VCC = 3.3V 1.5 2.4 VCC = 5.0V 1.8 2.4 Input Hysteresis 0.5 Input Resistance 3 5 V V 7 k TRANSMITTER OUTPUTS Output Voltage Swing All transmitter outputs loaded with 3k to ground 5 5.4 Output Resistance VCC = V+ = V- = 0, TOUT = 2V 300 10M Output Short-Circuit Current Output Leakage Current VOUT = 12V, VCC = 0 or 3V to 5.5V, transmitters disabled V 60 mA 25 A MOUSE DRIVEABILITY (MAX3243E) Transmitter Output Voltage T1IN = T2IN = GND, T3IN = VCC, T3OUT loaded with 3k to GND, T1OUT and T2OUT loaded with 2.5mA each 5.0 V ESD PROTECTION R_IN, T_OUT Maxim Integrated IEC 1000-4-2 Air-Gap Discharge 15 IEC 1000-4-2 Contact Discharge 8 Human Body Model 15 kV kV 3 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown TIMING CHARACTERISTICS--MAX3221E/MAX3223E/MAX3243E (VCC = +3.0V to +5.5V, C1-C4 = 0.1F (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL Maximum Data Rate tPHL Receiver Propagation Delay CONDITIONS MIN RL = 3k, CL = 1000pF, one transmitter switching 250 TYP UNITS kbps 0.15 CL = 150pF tPLH MAX s 0.15 Receiver Output Enable Time Normal operation 200 ns Receiver Output Disable Time Normal operation 200 ns (Note 3) 100 ns 50 ns Transmitter Skew tPHL - tPLH Receiver Skew tPHL - tPLH VCC = 3.3V, RL = 3k to 7k, TA = +25C, measured from +3V to -3V or -3V to +3V, one transmitter switching Transition-Region Slew Rate CL = 150pF to 1000pF 6 30 V/s Note 2: C1-C4 = 0.1F, tested at 3.3V 10%. C1 = 0.047F, C2-C4 = 0.33F, tested at 5.0V 10%. Note 3: Transmitter skew is measured at the transmitter zero cross points. Typical Operating Characteristics (VCC = +3.3V, 250kbps data rate, 0.1F capacitors, all transmitters loaded with 3k and CL, TA = +25C, unless otherwise noted.) VOUT+ 14 SLEW RATE (V/s) 12 T1 TRANSMITTING AT 250kbps T2 (MAX3223E) TRANSMITTING AT 15.6kbps -SLEW 10 +SLEW 8 6 4 -4 -5 -6 VOUT- 2 FOR DATA RATES UP TO 250kbps 0 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 4 16 MAX3221-TOC2 6 5 4 3 2 1 0 -1 -2 -3 MAX3221E/MAX3223E SLEW RATE vs. LOAD CAPACITANCE MAX3221E-01 TRANSMITTER OUTPUT VOLTAGE (V) MAX3221E/MAX3223E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 5000 0 1000 2000 3000 4000 5000 LOAD CAPACITANCE (pF) Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Typical Operating Characteristics (continued) (VCC = +3.3V, 250kbps data rate, 0.1F capacitors, all transmitters loaded with 3k and CL, TA = +25C, unless otherwise noted.) MAX3221E/MAX3223E OPERATING SUPPLY CURRENT vs. LOAD CAPACITANCE 250kbps 35 30 120kbps 25 20 20kbps 15 10 T1 TRANSMITTING AT 250kbps T2 (MAX3223E) TRANSMITTING AT 15.6kbps 5 0 -1 -2 -3 -4 VOUT- -6 0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) MAX3243E SLEW RATE vs. LOAD CAPACITANCE MAX3243E OPERATING SUPPLY CURRENT vs. LOAD CAPACITANCE 50 SUPPLY CURRENT (mA) 12 10 8 6 4 250kbps 40 120kbps 30 20kbps 20 10 2 0 5000 60 MAX3243E-05 14 SLEW RATE (V/s) 1 TRANSMITTER AT 250kbps 2 TRANSMITTERS AT 15.6kbps 2 1 -5 0 T1 TRANSMITTING AT 250kbps T2 (MAX3223E) TRANSMITTING AT 15.6kbps 0 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) Maxim Integrated VOUT+ 4 3 MAX3243E-06 SUPPLY CURRENT (mA) 40 6 5 TRANSMITTER OUTPUT VOLTAGE (V) MAX3224E-03 45 MAX3224E-04 MAX3243E TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 5000 0 1000 2000 3000 4000 5000 LOAD CAPACITANCE (pF) 5 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Pin Description PIN MAX3221E 6 MAX3223E MAX3243E SO/ SSOP/ TSSOP TQFNEP NAME FUNCTION TQFNEP SSOP/ TSSOP TQFNEP DIP/ SSOP/ TSSOP 14 1 19 1 -- 22 EN 16 2 1 2 28 28 C1+ 15 3 20 3 27 27 V+ +5.5V generated by the charge pump 1 4 2 4 24 23 C1- Negative terminal of the voltage doubler Charge-Pump Capacitor Receiver Enable Control. Drive low for normal operation. Drive high to force the receiver outputs (R_OUT) into a high-impedance state. Positive terminal of the voltage doubler Charge-Pump Capacitor 2 5 3 5 1 29 C2+ Positive terminal of inverting Charge-Pump Capacitor 3 6 4 6 2 30 C2- Negative terminal of inverting Charge-Pump Capacitor 4 7 5 7 3 31 V- 5 8 7, 14 9, 16 4-8 1-5 R_IN 6 9 8, 13 10, 15 15-19 13, 14, 15, 17, 18 R_OUT TTL/CMOS Receiver Outputs 7 10 9 11 21 -- INVALID Output of the Valid Signal Detector. INVALID is enabled high if a valid RS-232 level is present on any receiver input. 8 11 10, 11 12, 13 12, 13, 14 10, 11, 12 T_IN 9 12 12 14 23 -- FORCEON 10 13 6, 15 8, 17 9, 10, 11 6, 7, 8 T_OUT -- -- -- -- 20 19 R2OUTB 11 14 16 18 25 24 GND Ground 12 15 17 19 26 26 VCC +3.0V to +5.5V Supply Voltage 13 16 18 20 22 -- FORCEOF F -- -- -- -- -- 21 SHDN -5.5V generated by the charge pump RS-232 Receiver Inputs TTL/CMOS Transmitter Inputs Drive high to override automatic circuitry keeping transmitters and charge pump on (FORCEOFF must be high) (Table 1). RS-232 Transmitter Outputs TTL/CMOS Noninverting Complementary Receiver Output. Always active. Force-Off Input, active low. Drive low to shut down transmitters, receivers (MAX3243E, except R2OUTB), and on-board charge pump. This overrides all automatic circuitry and FORCEON (Table 1). Shutdown Control, Active Low Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Pin Description (continued) PIN MAX3221E MAX3223E MAX3243E FUNCTION TQFNEP SSOP/ TSSOP TQFNEP DIP/ SSOP/ TSSOP SO/ SSOP/ TSSOP TQFNEP NAME -- -- -- -- -- 19, 20 R_OUTB -- -- -- -- -- 9, 16, 25, 32 N.C. -- -- -- -- -- -- EP Noninverting Complementary Receiver Outputs. Always active. No Connection. Not internally connected. Exposed Paddle (TQFN package only). Solder the exposed paddle to the ground plane or leave unconnected. _______________Detailed Description Dual Charge-Pump Voltage Converter The MAX3221E/MAX3223E/MAX3243E's internal power supply consists of a regulated dual charge pump that provides output voltages of +5.5V (doubling charge pump) and -5.5V (inverting charge pump), over the +3.0V to +5.5V VCC range. The charge pumps operate in discontinuous mode: if the output voltages are less than 5.5V, the charge pumps are enabled; if the output voltages exceed 5.5V, the charge pumps are disabled. Each charge pump requires a flying capacitor (C1, C2) and a reservoir capacitor (C3, C4) to generate the V+ and V- supplies. POWERMANAGEMENT UNIT OR KEYBOARD CONTROLLER FORCEOFF FORCEON INVALID MAX3243E RS-232 Transmitters The transmitters are inverting level translators that convert CMOS-logic levels to 5.0V EIA/TIA-232 levels. They guarantee a 250kbps data rate with worst-case loads of 3k in parallel with 1000pF, providing compatibility with PC-to-PC communication software such as LapLinkTM. Transmitters can be paralleled to drive multiple receivers. The MAX3243E has been specifically designed to drive serial mice. Figure 1 shows a complete system connection. When FORCEOFF is driven to ground, or the AutoShutdown circuitry senses invalid voltage levels on all receiver inputs, the transmitters are disabled and the outputs are forced into a high-impedance state. When powered off or shut down, the output can be driven up to 12V. The transmitter inputs do not have pull-up resistors. CPU I/O CHIP WITH UART RS-232 Figure 1. Interface Under Control of PMU LapLink is a trademark of Traveling Software. Maxim Integrated 7 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown RS-232 Receivers VCC The MAX3221E/MAX3223E/MAX3243E's receivers convert RS-232 signals to CMOS-logic output levels. All receivers have inverting three-state outputs and can be active or inactive. In shutdown (FORCEOFF = low) or in AutoShutdown, the MAX3221E/MAX3223E's receivers are active (Table 1). Drive EN high to place the receiver(s) in a high-impedance state. The MAX3243E's receivers are high-impedance when the part is in shutdown (FORCEOFF = low). PROTECTION DIODE 5k UART Tx GND a) SHDN = GND OLDER RS-232: POWERED-DOWN UART DRAWS CURRENT FROM ACTIVE RECEIVER OUTPUT IN SHUTDOWN. VCC TO LOGIC P TRANSITION DETECTOR AutoShutdown The MAX3221E/MAX3223E/MAX3243E achieve a 1A supply current with Maxim's new AutoShutdown feature, which operates when FORCEON is low and FORCEOFF is high. When these devices sense no valid signal levels on all receiver inputs for 30s, the onboard charge pump and drivers are shut off, reducing supply current to 1A. This occurs if the RS-232 cable is disconnected or the connected peripheral transmitters are turned off. The device turns on again when a valid level is applied to any RS-232 receiver input. As a result, the system saves power without changes to the existing BIOS or operating system. Table 2 and Figure 3c summarize the MAX3221E/ MAX3223E/MAX3243E operating modes. FORCEON and FORCEOFF override AutoShutdown. When neither control is asserted, the IC selects between these states automatically, based on receiver input levels. Figures 3a, 3b, and 5a depict valid and invalid RS-232 receiver levels. Figure 5 shows the input levels and timing diagram for AutoShutdown operation. I Rx The MAX3243E features an extra, always-active complementary output (R2OUTB). R2OUTB monitors receiver activity while the other receivers are highimpedance. This allows Ring Indicator to be monitored without forward biasing other devices connected to the receiver outputs. This is ideal for systems where VCC drops to 0 in shutdown to accommodate peripherals such as UARTs (Figure 2). The MAX3221E/MAX3223E/MAX3243E feature an INVALID output that is enabled low when no valid RS-232 signal levels have been detected on all receiver inputs. INVALID is functional in any mode (Figures 3 and 5). PREVIOUS RS-232 VCC I PROTECTION DIODE MAX3243E R2OUTB VCC Rx THREE-STATED UART 5k Tx GND b) R2IN R2OUT T1IN T1OUT FORCEOFF = GND NEW MAX3243E: IN SHUTDOWN, R2OUTB IS USED TO MONITOR EXTERNAL DEVICES AND R2OUT IS THREE STATED, ELIMINATING A CURRENT PATH THROUGH THE UART'S PROTECTION DIODE. Figure 2. The MAX3243E detects RS-232 activity when the UART and interface are shut down. 8 Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Table 1. Output Control Truth Table FORCEON FORCEOFF EN (MAX3221E/ MAX3223E) VALID RECEIVER LEVEL T_OUT R_OUT (MAX3221E/ MAX3223E) R_OUT (MAX3243E) R2OUTB (MAX3243E) Shutdown (Forced Off) X 0 0 X High-Z Active High-Z Active X 0 1 X High-Z High-Z High-Z Active Normal Operation (Forced On) 1 1 0 X Active Active Active Active 1 1 1 X Active High-Z Active Active Normal Operation (AutoShutdown) 0 1 0 Yes Active Active Active Active 0 1 1 Yes Active High-Z Active Active Shutdown (AutoShutdown) 0 1 0 No High-Z Active Active Active 0 1 1 No High-Z High-Z Active Active OPERATION STATUS X = Don't Care +2.7V +0.3V R_IN -0.3V 30s COUNTER R TO MAX32_ _E POWER SUPPLY AND TRANSMITTERS INVALID * TRANSMITTERS ARE DISABLED, REDUCING SUPPLY CURRENT TO 1A IF ALL RECEIVER INPUTS ARE BETWEEN +0.3V AND -0.3V FOR AT LEAST 30s. Figure 3a. MAX32_ _E Entering 1A Supply Mode via AutoShutdown A mouse or other system with AutoShutdown may need time to wake up. Figure 4 shows a circuit that forces the transmitters on for 100ms, allowing enough time for the other system to realize that the MAX3221E/ MAX3223E/ MAX3243E are awake. If the other system transmits valid RS-232 signals within that time, the RS232 ports on both systems remain enabled. When shut down, the device's charge pumps are off, V+ is pulled to VCC, V- is pulled to ground, and the transmitter outputs are high impedance. The time required to exit shutdown is typically 100s (Figure 5b). Software-Controlled Shutdown If direct software control is desired, INVALID can be used to indicate DTR or Ring Indicator signal. Connect FORCEOFF and FORCEON together to disable AutoShutdown so the line acts like a SHDN input. Maxim Integrated R_IN -2.7V 30s COUNTER R TO MAX32_ _E POWER SUPPLY INVALID *TRANSMITTERS ARE ENABLED IF: ANY RECEIVER INPUT IS GREATER THAN +2.7V OR LESS THAN -2.7V. ANY RECEIVER INPUT HAS BEEN BETWEEN +0.3V AND -0.3V FOR LESS THAN 30s. Figure 3b. MAX32_ _E with Transmitters Enabled Using AutoShutdown 15kV ESD Protection As with all Maxim devices, ESD-protection structures are incorporated on all pins to protect against electrostatic discharges encountered during handling and assembly. The driver outputs and receiver inputs of the MAX3221E/MAX3223E/MAX3243E have extra protection against static electricity. Maxim's engineers have developed state-of-the-art structures to protect these pins against ESD of 15kV without damage. The ESD structures withstand high ESD in all states: normal operation, shutdown, and powered down. After an ESD event, Maxim's E versions keep working without latchup, whereas competing RS-232 products can latch and must be powered down to remove latchup. See Table 4. 9 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown FORCEOFF POWER DOWN FORCEON INVALID Table 2. INVALID Truth Table RS-232 SIGNAL PRESENT AT ANY RECEIVER INPUT INVALID OUTPUT Yes High No Low INVALID IS AN INTERNALLY GENERATED SIGNAL THAT IS USED BY THE AUTOSHUTDOWN LOGIC AND APPEARS AS AN OUTPUT OF THE DEVICE. POWER DOWN IS ONLY AN INTERNAL SIGNAL. IT CONTROLS THE OPERATIONAL STATUS OF THE TRANSMITTERS AND THE POWER SUPPLIES. Figure 3c. MAX32_ _E AutoShutdown Logic TRANSMITTERS ENABLED, INVALID HIGH MASTER SHDN LINE 0.1F 1M FORCEOFF FORCEON MAX3221E MAX3223E MAX3243E RECEIVER INPUT LEVELS POWERMANAGEMENT UNIT +2.7V INDETERMINATE +0.3V 0 AUTOSHUTDOWN, TRANSMITTERS DISABLED, 1A SUPPLY CURRENT, INVALID LOW -0.3V INDETERMINATE -2.7V TRANSMITTERS ENABLED, INVALID HIGH Figure 4. AutoShutdown with Initial Turn-On to Wake Up a Mouse or Another System ESD protection can be tested in various ways; the transmitter outputs and receiver inputs of this product family are characterized for protection to the following limits: a) 1) 15kV using the Human Body Model 2) 8kV using the Contact Discharge Method specified in IEC1000-4-2 3) 15kV using IEC1000-4-2's Air-Gap Method RECEIVER INPUT VOLTAGE (V) INVALID REGION ESD Test Conditions ESD performance depends on a variety of conditions. Contact Maxim for a reliability report that documents test setup, test methodology, and test results. Human Body Model Figure 6a shows the Human Body Model, and Figure 6b shows the current waveform it generates when discharged into a low impedance. This model consists of a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the test device through a 1.5k resistor. IEC1000-4-2 The IEC1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically refer to integrated circuits. The MAX3221E/ MAX3223E/ MAX3243E help you design equipment that meets 10 VCC INVALID OUTPUT (V) 0 tINVL tINVH tWU V+ VCC 0 V- b) Figure 5. AutoShutdown Trip Levels Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown RC 1M CHARGE-CURRENT LIMIT RESISTOR HIGHVOLTAGE DC SOURCE Cs 100pF RD 1500 RC 50M to 100M DISCHARGE RESISTANCE DISCHARGE RESISTANCE CHARGE CURRENT LIMIT RESISTOR DEVICE UNDER TEST STORAGE CAPACITOR Figure 6a. Human Body ESD Test Models HIGHVOLTAGE DC SOURCE RD 330 Cs 150pF STORAGE CAPACITOR DEVICE UNDER TEST Figure 7a. IEC1000-4-2 ESD Test Model I IP 100% 90% Ir 100% PEAK-TO-PEAK RINGING (NOT DRAWN TO SCALE) 90% I PEAK AMPERES 36.8% 10% 0 0 tRL TIME tDL CURRENT WAVEFORM Figure 6b. Human Body Model Current Waveform Level 4 (the highest level) of IEC1000-4-2, without the need for additional ESD-protection components. The major difference between tests done using the Human Body Model and IEC1000-4-2 is higher peak current in IEC1000-4-2, because series resistance is lower in the IEC1000-4-2 model. Hence, the ESD withstand voltage measured to IEC1000-4-2 is generally lower than that measured using the Human Body Model. Figure 7a shows the IEEE1000-4-2 model and Figure 7b shows the current waveform for the 8kV IEC1000-4-2 Level 4 ESD contact-discharge test. The air-gap test involves approaching the device with a charged probe. The contact-discharge method connects the probe to the device before the probe is energized. Machine Model The Machine Model for ESD tests all pins using a 200pF storage capacitor and zero discharge resistance. Its objective is to emulate the stress caused by contact that occurs with handling and assembly during manufacturing. Of course, all pins require this protection during manufacturing, not just RS-232 inputs and outputs. Maxim Integrated 10% t r = 0.7ns to 1ns t 30ns 60ns Figure 7b. IEC1000-4-2 ESD Generator Current Waveform Therefore, after PC board assembly, the Machine Model is less relevant to I/O ports. ___________Applications Information Capacitor Selection The capacitor type used for C1-C4 is not critical for proper operation; either polarized or nonpolarized capacitors may be used. The charge pump requires 0.1F capacitors for 3.3V operation. For other supply voltages, refer to Table 3 for required capacitor values. Do not use values smaller than those listed in Table 3. Increasing the capacitor values (e.g., by a factor of 2) reduces ripple on the transmitter outputs and slightly reduces power consumption. C2, C3, and C4 can be increased without changing C1's value. However, do not increase C1 without also increasing the values of C2, C3, and C4 to maintain the proper ratios (C1 to the other capacitors). 11 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown When using the minimum required capacitor values, make sure the capacitor value does not degrade excessively with temperature. If in doubt, use capacitors with a larger nominal value. The capacitor's equivalent series resistance (ESR) usually rises at low temperatures and influences the amount of ripple on V+ and V-. Table 3. Required Capacitor Values VCC (V) C1, CBYPASS (F) C2, C3, C4 (F) 3.0 to 3.6 0.22 0.22 3.15 to 3.6 0.1 0.1 Power-Supply Decoupling 4.5 to 5.5 0.047 0.33 In most circumstances, a 0.1F VCC bypass capacitor is adequate. In applications that are sensitive to powersupply noise, use a capacitor of the same value as the charge-pump capacitor C1. Connect bypass capacitors as close to the IC as possible. 3.0 to 5.5 0.22 1 FORCEON = FORCEOFF T2OUT 5V/div Transmitter Outputs when Exiting Shutdown Figure 8 shows two transmitter outputs when exiting shut down mode. As they become active, the two transmitter outputs are shown going to opposite RS-232 levels (one transmitter output is high, the other is low). Each transmitter is loaded with 3k in parallel with 1000pF. The transmitter outputs display no ringing or undesirable transients as they come out of shutdown, and are enabled only when the magnitude of Vexceeds approximately -3V. High Data Rates The MAX3221E/MAX3223E/MAX3243E maintain the RS232 5.0V minimum transmitter output voltage even at high data rates. Figure 9 shows a transmitter loopback test circuit. Figure 10 shows a loopback test result at 120kbps, and Figure 11 shows the same test at 250kbps. For Figure 10, all three transmitters were driven simultaneously at 120kbps into RS-232 loads in parallel with 1000pF. For Figure 11, a single transmitter was driven at 250kbps, and all three transmitters were loaded with an RS-232 receiver in parallel with 1000pF. Mouse Driveability (MAX3243E) The MAX3243E has been specifically designed to power serial mice while operating from low-voltage power supplies. It has been tested with leading mouse brands such 2V/div T1OUT VCC = 3.3V C1-C4 = 0.1F 40s/div Figure 8. Transmitter Outputs Exiting Shutdown or Powering Up as Logitech and Microsoft. When tested, the MAX3243E successfully drove all serial mice and met their respective current and voltage requirements. The MAX3243E's regulated dual charge pump ensures the transmitters will supply at least 5V during worst-case conditions. Figure 12a shows the transmitter outputs under increasing load current. The AutoShutdown feature does not work with a mouse, so FORCEOFF and FORCEON should be connected to VCC. Figure 12b (on the following page) shows a mouse driver test circuit. To achieve mouse driveability with 1A supply current when the port is inactive, use parts with the AutoShutdown PlusTM feature (such as the MAX3244E and MAX3245E). AutoShutdown Plus is a trademark of Maxim Integrated Products, Inc. 12 Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Table 4. 15kV ESD-Protected, 3.0V to 5.5V Powered RS-232 Transceivers from Maxim PART SUPPLY VOLTAGE RANGE (V) NO. SUPPLY AutoOF CURRENT Shutdown Tx/Rx (A) Plus MAX3241E +3.0 to +5.5 3/5 300 MAX3243E +3.0 to +5.5 3/5 MAX3244E +3.0 to +5.5 3/5 MAX3245E +3.0 to +5.5 AutoShutdown HUMAN BODY MODEL (kV) IEC 1000-4-2 CONTACT DISCHARGE (kV) IEC 1000-4-2 AIR-GAP DISCHARGE (kV) GUARANTEED DATA RATE (kbps) -- -- 15 8 15 250 1 -- Yes 15 8 15 250 1 Yes -- 15 8 15 250 3/5 1 Yes -- 15 8 15 1Mbps MAX3232E +3.0 to +5.5 2/2 300 -- -- 15 8 15 250 MAX3222E +3.0 to +5.5 2/2 300 -- -- 15 8 15 250 MAX3223E +3.0 to +5.5 2/2 1 -- Yes 15 8 15 250 MAX3224E +3.0 to +5.5 2/2 1 Yes -- 15 8 15 250 MAX3225E +3.0 to +5.5 2/2 1 Yes -- 15 8 15 1Mbps MAX3221E +3.0 to +5.5 1/1 1 -- Yes 15 8 15 250 MAX3226E +3.0 to +5.5 1/1 1 Yes -- 15 8 15 250 MAX3227E +3.0 to +5.5 1/1 1 Yes -- 15 8 15 1Mbps VCC 0.1F 5V/div T1IN C1+ VCC V+ C3 C1 C1C2+ C2 C2- 5V/div MAX3221E MAX3223E MAX3243E T1OUT VC4 5V/div R1OUT T_ OUT T_ IN 2s/div R_ IN R_ OUT 0 VCC = 3.3V EN (MAX3221E/3E) Figure 10. Loopback Test Result at 120kbps 5k 1000pF VCC FORCEOFF GND Figure 9. Loopback Test Circuit Maxim Integrated 13 5V/div T1OUT 5V/div R1OUT VCC = 3.3V 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 VOUT+ VCC VOUTVOUT- 0 2s/div VOUT+ VCC = 3.0V MAX2343E-FIG15 5V/div T1IN TRANSMITTER OUTPUT VOLTAGE (V) MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown 1 2 3 4 5 6 7 8 9 10 LOAD CURRENT PER TRANSMITTER (mA) Figure 11. Loopback Test Result at 250kbps Table 5. Logic Family Compatibility with Various Supply Voltages VCC SUPPLY VOLTAGE (V) COMPATIBILITY 3.3 3.3 Compatible with all CMOS families. 5 5 3.3 Compatible with all TTL and CMOS-logic families. Compatible with ACT and HCT CMOS, and with TTL. Incompatible with AC, HC, or CD4000 CMOS. Interconnection with 3V and 5V Logic The MAX3221E/MAX3223E/MAX3243E can directly interface with various 5V logic families, including ACT and xHCT CMOS. See Table 5 for more information on possible combinations of interconnections. 14 Ordering Information (continued) PART SYSTEM POWERSUPPLY VOLTAGE (V) 5 Figure 12a. Transmitter Output Voltage vs. Load Current per Transmitter TEMP RANGE PIN-PACKAGE MAX3243ECWI+ 0C to +70C MAX3243ECAI+ 0C to +70C 28 Wide SO 28 SSOP MAX3243ECUI+ 0C to +70C 28 TSSOP MAX3243EEWI+ -40C to +85C 28 Wide SO MAX3243EEAI+ -40C to +85C 28 SSOP MAX3243EEUI+ -40C to +85C 28 TSSOP MAX3243ECTJ+ 0C to +70C 32 TQFN-EP* MAX3243EETJ+ -40C to +85C 32 TQFN-EP* *Exposed pad. +Denotes a lead(Pb)-free/RoHS-compliant package. ___________________Chip Information PROCESS: BiCMOS Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown +3.3V 26 0.1F 28 C1 0.1F 24 1 C2 0.1F 2 LOGIC INPUTS VCC 27 C1+ V+ C3 0.1F C1C2+ COMPUTER SERIAL PORT 3 MAX3243E V- C4 0.1F C2- 14 T1IN T1OUT 9 +V 13 T2IN T2OUT 10 +V 12 T3IN T3OUT 11 -V 20 R2OUTB 19 R1OUT GND R1IN 4 R2IN 5 Tx 5k 18 R2OUT 5k LOGIC OUTPUTS 17 R3OUT R3IN 6 RS-232 INPUTS 5k 16 R4OUT R4IN 7 5k 15 VCC VCC TO POWERMANAGEMENT UNIT 23 22 21 R5OUT R5IN 8 SERIAL MOUSE 5k FORCEON FORCEOFF INVALID GND 25 Figure 12b. Mouse Driver Test Circuit Maxim Integrated 15 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Typical Operating Circuits +3.3V 15 0.1F CBYPASS 2 C1+ C1 0.1F 4 5 C2 0.1F 6 C1- VCC 3 V+ MAX3221E* C2+ V- C3 0.1F C4 0.1F C2- 11 T1IN +3.3V 7 12 INVALID 10 FORCEOFF 16 FORCEON GND TO POWERMANAGEMENT UNIT 2 LOGIC INPUTS VCC 14 C1 0.1F C2 0.1F 0.1F 2 C1+ 4 C1- 6 C3 0.1F MAX3243E V- 3 C4 0.1F C2- 14 T1IN T1OUT 9 13 T2IN T2OUT 10 12 T3IN T3OUT 11 RS-232 OUTPUTS R1IN 4 19 5k VCC 3 V+ MAX3223E** C2+ V- 18 R2OUT C3 0.1F 7 C4 0.1F C2- LOGIC OUTPUTS R2IN 5 5k 17 R3OUT R3IN 6 RS-232 INPUTS 5k 13 T1IN TTL/CMOS INPUTS C2+ 19 R1OUT 5 27 V+ 20 R2OUTB +3.3V CBYPASS VCC 24 C1- C2 0.1F 5k 1 EN 28 C1+ 1 R1IN 8 26 0.1F C1 0.1F T1OUT 13 9 R1OUT CBYPASS T1OUT 17 T2OUT 8 12 T2IN 16 R4OUT RS-232 OUTPUTS R4IN 7 5k 15 R5OUT R1IN 16 15 R1OUT TTL/CMOS OUTPUTS 23 RS-232 INPUTS 5k R2IN 10 R2OUT 9 VCC TO POWERMANAGEMENT UNIT 5k 22 R5IN 8 5k FORCEON FORCEOFF 21 INVALID GND 25 INVALID 11 1 EN 14 FORCEOFF 20 FORCEON GND TO POWERMANAGEMENT UNIT VCC *MAX3221E PIN OUT REFERS TO SSOP/TSSOP PACKAGES. **MAX3223E PIN OUT REFERS TO DIP/SSOP/TSSOP PACKAGES. 18 16 Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Pin Configurations TOP VIEW + + EN 1 EN 1 16 FORCEOFF 15 VCC C1+ 2 V+ 3 14 GND C1+ 2 19 VCC V+ 3 18 GND 13 T1OUT C1- 4 C2+ 5 12 FORCEON C2+ 5 C2- 6 11 T1IN C2- 6 MAX3221E C1- 4 V- 7 17 T1OUT MAX3223E 16 R1IN 15 R1OUT V- 7 10 INVALID 9 R1OUT R1IN 8 20 FORCEOFF SSOP/TSSOP 14 FORCEON T2OUT 8 13 T1IN R2IN 9 12 T2IN R2OUT 10 11 INVALID EN SHDN R1OUTB R2OUTB R1OUT R2OUT 23 22 21 20 19 18 17 C2- 2 27 V+ V- 3 26 VCC R1IN 4 25 GND N.C. 25 16 N.C. R2IN 5 24 C1- VCC 26 15 R3OUT 23 FORCEON V+ 27 14 R4OUT R4IN 7 22 FORCEOFF C1+ 28 13 R5OUT R5IN 8 21 INVALID C2+ 29 12 T1IN T1OUT 9 20 R2OUTB C2- 30 11 T2IN T2OUT 10 19 R1OUT V- 31 10 T3IN T3OUT 11 18 R2OUT N.C. 32 9 N.C. T3IN 12 17 R3OUT T2IN 13 16 R4OUT 1 2 3 T1IN 14 15 R5OUT R3IN C1- 24 28 C1+ R2IN TOP VIEW C2+ 1 R1IN + GND DIP/SSOP/TSSOP SO/SSOP/TSSOP MAX3243E 4 5 6 7 8 R5IN T1OUT T2OUT T3OUT + R4IN MAX3243E R3IN 6 TQFN-EP *CONNECT EP TO GND OR LEAVE UNCONNECTED Maxim Integrated 17 MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Pin Configurations (continued) VCC GND T1OUT FORCEON T1OUT R1IN R1OUT FORCEON T1IN TOP VIEW 12 11 10 9 15 14 13 12 11 FORCEOFF 13 8 T1IN EN 14 7 INVALID 6 R1OUT 10 T2IN VCC 17 9 INVALID 8 R2OUT 7 R2IN 6 T2OUT FORCEOFF 18 MAX3221E* V+ 15 GND 16 MAX3223E* EN 19 3 4 1 2 C1+ C1- TQFN 3 4 5 V- 2 C2- 1 V- + C2- V+ 20 C2+ R1IN C2+ 5 + C1- C1+ 16 TQFN *CONNECT EP TO GND OR LEAVE UNCONNECTED *CONNECT EP TO GND OR LEAVE UNCONNECTED Package Information For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 16 TQFN-EP T1655+2 21-0140 90-0072 16 SSOP A16+2 21-0056 90-0106 16 TSSOP U16+1 21-0066 90-0117 20 TQFN-EP T2055+5 21-0140 90-0010 20 SSOP A20+2 21-0056 90-0094 20 TSSOP U20+2 21-0066 90-0116 PACKAGE TYPE 18 20 PDIP P20+3 21-0043 -- 28 Wide SO W28+6 21-0042 90-0109 28 SSOP A28+1 21-0056 90-0095 28 TSSOP U28+2 21-0066 90-0171 32 TQFN-EP T3277+2 21-0144 90-0125 Maxim Integrated MAX3221E/MAX3223E/MAX3243E 15kV ESD-Protected, 1A, 3.0V to 5.5V, 250kbps, RS-232 Transceivers with AutoShutdown Revision History REVISION NUMBER REVISION DATE 7 8/11 DESCRIPTION Added MAX3223EEUP/V+ automotive qualified part and updated Ordering Information to show lead-free versions PAGES CHANGED 1, 2, 14, 17, 18 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 (c) Maxim Integrated 19 The Maxim logo and Maxim Integrated are trademarks of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX3221ECAE+ MAX3221ECTE+ MAX3221EEAE+ MAX3223ECAP+ MAX3223ECUP+ MAX3223EEAP+ MAX3223EEPP+ MAX3223EETP+ MAX3223EEUP+ MAX3243ECAI+ MAX3243ECUI+ MAX3243EEAI+ MAX3243EEUI+ MAX3221EEAE+G071 MAX3223EEAP+G071 MAX3243EEAI+G071 MAX3221EEAE+TG071 MAX3223EEAP+TG071 MAX3243EEAI+TG071 MAX3223EEAP-T MAX3221ECAE+T MAX3221ECTE+T MAX3221ECUE+ MAX3221ECUE+T MAX3221EEAE MAX3221EEAE+T MAX3221EEAE-T MAX3221EETE+ MAX3221EETE+T MAX3221EEUE+ MAX3221EEUE+T MAX3223ECAP+T MAX3223ECPP+ MAX3223ECTP+ MAX3223ECTP+T MAX3223ECUP+T MAX3223EEAP MAX3223EEAP+T MAX3223EETP+T MAX3223EEUP+T MAX3243ECAI+T MAX3243ECUI+T MAX3243ECWI+ MAX3243ECWI+T MAX3243EEAI+T MAX3243EEUI+T MAX3243EEWI+ MAX3243EEWI+T MAX3221EEAE/GG8-T MAX3202EEWS+T MAX3243EETJ+