Intellimod™ Module
Dual-In-Line Intelligent
Power Module
15 Amperes/600 Volts
PS219B4-S, PS219B4-AS,
PS219B4-CS
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
www.pwrx.com
1
12/11 Rev. 0
Description:
DIP-IPMs are intelligent power
modules that integrate power
devices, drivers, and protection
circuitry in an ultra compact
dual-in-line transfer-mold package
for use in driving small three
phase motors. Use of 6th
generation CSTBT IGBTs, DIP
packaging, and application specific
HVICs allow the designer to reduce
inverter size and overall design
time.
Features:
£ Compact Packages
£ Single Power Supply
£ Integrated HVICs
£ Direct Connection to CPU
£ Linear, Analog Temperature
Feedback
Applications:
£ Small Servo Motors
£ Small Motor Control
Ordering Information:
PS219B4-S is a 600V, 15 Ampere
short pin DIP Intelligent Power
Module.
PS219B4-AS – long pin type
PS219B4-CS – zigzag pin type
Dim. Inches Millimeters
A 1.50±0.02 38.0±0.5
B 0.94±0.02 24.0±0.5
C 0.14 3.5
D 1.40 35.56
E 0.57±0.02 14.4±0.5
F 0.74±0.02 18.9±0.5
G 1.15±0.02 29.2±0.5
H 0.14 3.5
J 0.13 3.3
K 0.016 0.4
L 0.06±0.02 1.5±0.05
M 0.031 0.8
N 1.38±0.019 35.0±0.3
O 0.07±0.008 1.778±0.2
P 0.02 0.5
Q 0.47 12.0
R 0.011 0.28
Dim. Inches Millimeters
S 0.1046 2.656
T 0.024 0.6
U 0.1±0.008 2.54±0.2
V 1.33±0.02 33.7±0.5
W 0.1085 2.756
X 0.04 1.0
Y 0.05 1.2
Z 1.40 35.56
AA 0.22±0.02 5.5±0.5
AB 0.37±0.02 9.5±0.5
AC 0 ~ 5° 0 ~ 5°
AD 0.06 Min. 1.5 Min.
AE 0.05 1.2
AF 0.063 Rad. 1.6 Rad.
AG 0.118 Min. 3.0 Min.
AH 0.098 Min. 2.5 Min.
Outline Drawing and Circuit Diagram
D
N
O P
A
HEATSINK SIDE
B
Q
R
R
T
AG
U
P P
PP
AA
AE
AF
AD
AC
1234
567891011121314151617
2524232221201918
X
DETAIL “A”
DETAIL “B”
DETAIL "A"
Z
Y
Y
W
DETAIL "C"
S
AH
2
1-B
1-A
TERMINAL
NUMBER
HEATSINK
SIDE
E
G
H
M
E
F
V
C
J
L
DETAIL "B"
K
K
K
DETAIL "C"
10 UN
11 VN
12 WN
13 VN1
14 FO
5 UP
6 VP
7 WP
8 VP1
9 VNC*
1-A NC(VNC)
1-B NC(VP1)
2 VUFB
3 VVFB
4 VWFB
20 NU
21 W
22 V
23 U
24 P
15 CIN
16 VNC*
17 VOT
18 NW
19 NV
TERMINAL CODE
*Two VNC terminals (9 & 16) are connected inside DIPIPM, please connect
either one to the 15V power supply GND outside and leave the other one open.
25 NC
AB
PS219B4-S
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
212/11 Rev. 0
Dim. Inches Millimeters
A 1.50±0.02 38.0±0.5
B 0.94±0.02 24.0±0.5
C 0.14 3.5
D 1.40 35.56
E 0.57±0.02 14.4±0.5
F 0.063 Rad. 1.6 Rad.
G 1.16±0.02 29.4±0.5
H 0.14 3.5
J 0.13 3.3
K 0.016 0.4
L 0.06±0.02 1.5±0.05
M 0.031 0.8
N 1.38±0.019 35.0±0.3
O 0.07±0.008 1.778±0.2
P 0.02 0.5
Q 0.47 12.0
Dim. Inches Millimeters
R 0.011 0.28
S 0.1046 2.656
T 0.024 0.6
U 0.1±0.008 2.54±0.2
V 0.098 Min. 2.5 Min.
W 0.1085 2.756
X 0.04 1.0
Y 0.05 1.2
Z 1.40 35.56
AA 0.22±0.02 5.5±0.5
AB 0.55±0.02 14.0±0.5
AC 0 ~ 5° 0 ~ 5°
AD 0.06 Min. 1.5 Min.
AE 0.05 1.2
AF 0.118 Min. 3.0 Min.
Outline Drawing and Circuit Diagram
D
N
O P
A
HEATSINK SIDE
B
Q
R
R
T
U
P
AA
AE
F
AD
AC
1234
567891011121314151617
2524232221201918
X
DETAIL “A”
DETAIL “B”
DETAIL "A"
Z
Y
Y
W
DETAIL "C"
S
V
2
1-B
1-A
TERMINAL
NUMBER
HEATSINK
SIDE
E
G
H
M
E
C
J
L
DETAIL "B"
K
K
DETAIL "C"
10 UN
11 VN
12 WN
13 VN1
14 FO
5 UP
6 VP
7 WP
8 VP1
9 VNC*
1-A NC(VNC)
1-B NC(VP1)
2 VUFB
3 VVFB
4 VWFB
20 NU
21 W
22 V
23 U
24 P
15 CIN
16 VNC*
17 VOT
18 NW
19 NV
TERMINAL CODE
*Two VNC terminals (9 & 16) are connected inside DIPIPM, please connect
either one to the 15V power supply GND outside and leave the other one open.
25 NC
P
PP
AF
AB
PS219B4-AS
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
3
12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Dim. Inches Millimeters
A 1.50±0.02 38.0±0.5
B 0.94±0.02 24.0±0.5
C 0.14 3.5
D 1.40 35.56
E 0.57±0.02 14.4±0.5
F 0.74±0.02 18.9±0.5
G 1.15±0.02 29.2±0.5
H 0.14 3.5
J 0.13 3.3
K 0.016 0.4
L 0.06±0.02 1.5±0.05
M 0.031 0.8
N 1.38±0.019 35.0±0.3
O 0.07±0.008 1.778±0.2
P 0.02 0.5
Q 0.47 12.0
Dim. Inches Millimeters
R 0.011 0.28
S 0.1046 2.656
T 0.024 0.6
U 0.1±0.008 2.54±0.2
V 1.33±0.02 33.7±0.5
W 0.1085 2.756
X 0.04 1.0
Y 0.05 1.2
Z 1.40 35.56
AA 0.22±0.02 5.5±0.5
AB 0.37±0.02 9.5±0.5
AC 0 ~ 5° 0 ~ 5°
AD 0.06 Min. 1.5 Min.
AE 0.05 1.2
AF 0.063 Rad. 1.6 Rad.
AG 0.118 Min. 3.0 Min.
Outline Drawing and Circuit Diagram
D
N
O P
A
B
Q
R
R
T
U
AE
AF
AD
AC
AC
1234
567891011121314151617
2524232221201918
X
DETAIL “A”
DETAIL “B”
DETAIL "A"
Z
Y
Y
W
DETAIL "C"
S
2
1-B
1-A
TERMINAL
NUMBER
HEATSINK
SIDE
E
G
V
H
M
E
F
C
J
L
DETAIL "B"
K
K
K
DETAIL "C"
10 UN
11 VN
12 WN
13 VN1
14 FO
5 UP
6 VP
7 WP
8 VP1
9 VNC*
1-A NC(VNC)
1-B NC(VP1)
2 VUFB
3 VVFB
4 VWFB
20 NU
21 W
22 V
23 U
24 P
15 CIN
16 VNC*
17 VOT
18 NW
19 NV
TERMINAL CODE
*Two VNC terminals (9 & 16) are connected inside DIPIPM, please connect
either one to the 15V power supply GND outside and leave the other one open.
25 NC
HEATSINK SIDE
P P P
AA AB
AG
PS219B4-CS
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
412/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Absolute Maximum Ratings, Tj = 25°C unless otherwise specied
PS219B4-S, PS219B4-AS,
Characteristics Symbol PS219B4-CS Units
Inverter Part
Supply Voltage (Applied between P-NU, NV, NW) VCC 450 Volts
Supply Voltage, Surge (Applied between P-NU, NV, NW) VCC(surge) 500 Volts
Collector-Emitter Voltage VCES 600 Volts
Each IGBT Collector Current (TC = 25°C) ±IC 15 Amperes
Each Peak Collector Current (TC = 25°C, Less than 1ms) ±ICP 30 Amperes
ollector Dissipation (TC = 25°C, per 1 Chip) PC 33.3 Watts
Power Device Junction Temperature*1 Tj -20 ~ +150 °C
Control (Protection) Part
Control Supply Voltage (Applied between VP1-VNC, VN1-VNC) VD 20 Volts
Control Supply Voltage (Applied between VUFB-U, VVFB-V, VWFB-W) VDB 20 Volts
Input Voltage (Applied between UP
, VP
, WP-VNC, UN, VN, WN-VNC) VIN -0.5 ~ VD+0.5 Volts
Fault Output Supply Voltage (Applied between FO-VNC) VFO -0.5 ~ VD+0.5 Volts
Fault Output Current (Sink Current at FO Terminal) IFO 1 mA
Current Sensing Input Voltage (Applied between CIN-VNC) VSC -0.5 ~ VD+0.5 Volts
Total System
Self-protection Supply Voltage Limit, Short Circuit Protection Capability VCC(prot.) 400 Volts
(VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C, Non-repetitive less than 2µs)
Module Case Operating Temperature*2 TC -20 ~ +100 °C
Storage Temperature Tstg -40 ~ +125 °C
Isolation Voltage, 60Hz, Sinusoidal 1 Minute, All Connected Pins to Heatsink Plate VISO 1500 Vrms
Thermal Resistance
Junction to Case*3 Rth(j-c)Q Inverter IGBT Part (Per 1/6 Module) — — 3.0 °C/Watt
Rth(j-c)D Inverter FWDi Part (Per 1/6 Module) — — 3.9 °C/Watt
*1 The maximum junction temperature rating of the power chips integrated within the DIPIPM is 150°C (@TC ≤ 100°C). However, to ensure safe operation of the DIPIPM,
the average junction temperature should be limited to Tj(avg) ≤125°C (@TC ≤ 100°C).
*2 TC measurement point
*3 Good thermal grease with long-term quality should be applied evenly with +100µm ~ +200µm on the contacting surface of the DIPIPM and heatsink. The contacting thermal resistance
between DIPIPM case and heatsink (Rth(c-f)) is determined by the thickness and the thermal conductivity of the applied grease. For reference, Rth(c-f) (per 1/6 module) is about 0.3°C/W
when the grease thickness is 20µm and the thermal conductivity is 1.0W/mK.
FWDi CHIP POSITION
POWER TERMINALS
CONTROL TERMINALS
IGBT CHIP POSITION
HEATSINK SIDE
TC POINT
11.6mm 3.0mm
DIPIPM
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
5
12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specied
Characteristics Symbol Test Conditions Min. Typ. Max. Units
Inverter Part
Collector-Emitter Saturation Voltage VCE(sat) VD = VDB = 15V, IC = 15A, VIN = 5V, Tj = 25°C — 1.50 2.00 Volts
VD = VDB = 15V, IC = 15A, VIN = 5V, Tj = 125°C — 1.60 2.10 Volts
Diode Forward Voltage VEC -IC = 15A, VIN = 0V — 1.70 2.20 Volts
Switching Times ton 0.85 1.45 2.05 µs
trr VCC = 300V, VD = VDB = 15V, — 0.30 — µs
tC(on) IC = 15A, Tj = 125°C, — 0.35 0.55 µs
toff VIN = 0 ⇔ 5V, Inductive Load — 1.50 2.10 µs
tC(off) — 0.30 0.60 µs
Collector-Emitter Cutoff Current ICES VCE = VCES, Tj = 25°C — — 1.0 mA
VCE = VCES, Tj = 125°C — — 10 mA
Control (Protection) Part
Circuit Current ID VIN = 0V, VD = 15V Total of VP1-VNC, VN1-VNC — — 2.80 mA
VIN = 5V, VD = 15V Total of VP1-VNC, VN1-VNC — — 2.80 mA
IDB VIN = 0V, VD = VDB = 15V Each Part of VUFB-U, VVFB-V, VWFB-W — — 0.10 mA
VIN = 5V, VD = VDB = 15V Each Part of VUFB-U, VVFB-V, VWFB-W — — 0.10 mA
Fault Output Voltage VFOH VSC = 0V, FO Terminal Pull-up to 5V by 10kΩ 4.9 — — Volts
VFOL VSC = 1V, IFO = 1mA — — 0.95 Volts
Input Current IIN VIN = 5V 0.70 1.00 1.50 mA
Short Circuit Trip Level VSC(ref) VD = 15V*4 0.43 0.48 0.53 Volts
Temperature Output VOT LVIC Temperature = 90°C 2.63 2.77 2.91 Volts
Pull Down R = 5kΩ*6 LVIC Temperature = 25°C 0.88 1.13 1.39 Volts
Control Supply UVDBt Trip Level, Tj ≤ 125°C 7.0 10.0 12.0 Volts
Under-voltage Protection UVDBr Reset Level, Tj ≤ 125°C 7.0 10.0 12.0 Volts
UVDt Trip Level, Tj ≤ 125°C 10.3 — 12.5 Volts
UVDr Reset Level, Tj ≤ 125°C 10.8 — 13.0 Volts
Fault Output Pulse Width*5 tFO 20 — — µs
ON Threshold Voltage Vth(on) Applied between — 2.1 2.6 Volts
OFF Threshold Voltage Vth(off) UP
, VP
, WP-VNC, 0.8 1.3 — Volts
ON/OFF Threshold Hysteresis Voltage Vth(hys) UN, VN, WN-VNC 0.35 0.65 — Volts
Bootstrap Diode Forward Voltage*7 VF IF = 10mA, 1.1 1.7 2.3 Volts
Including Voltage Drop by Limiting Resistor
Built-in Limiting Resistance R For Bootstrap Circuit 80 100 120 Ω
*4 Short Circuit protection is functioning only for N-side IGBTs. Please select the value of the external shunt resistor such that the SC trip level is less than 1.7 times the current rating.
*5 Fault signal, FO, outputs when SC or UV protection works. FO pulse width is different for each protection mode. At SC failure, FO pulse width is a fixed width (=min. 20µs), however, at UV
failure, FO outputs continuously until recovering from UV state. Minimum FO pulse width is 20µs.
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
612/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
*6 The DIPIPM does not automatically shutdown the IGBTs and fault signal when temperature rises excessively. When the temperature exceeds the protective level that is defined by the
user, the controller (MCU) should stop the DIPIPM. The temperature of LVIC vs. VOT output characteristics is shown in the following graph. VOT output may exceed 3.3V when the
temperature rises excessively, therefore, it is recommended for protection of the control part (MCU) to insert a clamp diode between the control supply (3.3V) and VOT output.
*7 Bootstrap Diode (@Ta = 25°C) Characteristics
LVIC TEMPERATURE, (°C)
OUTPUT, VOT, (VOLTS)
LVIC TEMPERATURE VS. TEMPERATURE OUTPUT
CHARACTERISTICS
60 8070 90 110100 120
3.00
2.50
2.00
1.50
3.50
4.00
3.15
2.77
2.40
90±5°C
75±6°C
106±6°C
FORWARD VOLTAGE, VF, (VOLTS)
FORWARD CURRENT, IF, (mA)
FORWARD VOLTAGE-FORWARD CURRENT
CURVE FOR BOOTSTRAP
DIODE FORWARD VOLTAGE-FORWARD
CURRENT CURVE FOR BOOTSTRAP DIODE
(MAGNIFIED VIEW)
0 1 2 3 4 5 6 7 8 9 101112131415
40
0
80
160
140
120
100
60
20
FORWARD VOLTAGE, VF, (VOLTS)
FORWARD CURRENT, IF, (mA)
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
5
0
15
10
30
25
20
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
7
12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Mechanical Characteristics and Ratings
Characteristic Symbol Condition Min. Typ. Max. Units
Mounting Torque M3 Mounting Screws*8 5.2 6.1 6.9 in-lb
Terminal Pulling Strength Control Terminal: Weight 4.9N 10 — — s
Power Terminal: Weight 9.8N
Terminal Bending Strength Control Terminal: Weight 2.45N 2 — — times
Power Terminal: Weight 4.9N
90 Degree Bend
Module Weight (Typical) — 8.5 — Grams
Heatsink Flatness*9 -50 — +100 µm
Recommended Conditions for Use
Characteristic Symbol Condition Min. Typ. Max. Units
Supply Voltage VCC Applied between P-N Terminals 0 300 400 Volts
Control Supply Voltage VD Applied between VP1-VNC, VN1-VNC 13.5 15.0 16.5 Volts
VDB Applied between VUFB-U, 13.0 15.0 18.5 Volts
VVFB-V, VWFB-W
Control Supply Variation ∆VD, ∆VDB -1 — 1 V/µs
Arm Shoot-through Blocking Time tDEAD For Each Input Signal, TC ≤ 100°C 1.0 — — µs
Allowable Minimum Input PWIN(on)
0.7 — — µs
Pulse Width* 11 PWIN(off) 0.7 — — µs
VNC Voltage Variation VNC Between VNC-NU, NV, NW (Including Surge) -5.0 — 5.0 Volts
Junction Temperature Tj -20 125 °C
*8 Plain washers (ISO 7089-7094) are recommended.
*9 Flatness measurement position.
*11 DIPIPM may not respond if the input signal pulse is less than PWIN(on), PWIN(off).
HEATSINK
MEASUREMENT POSITION
4.6mm
17.5mm
HEATSINK
–
+
–+
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
812/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Application Circuit
Bootstrap negative
electrodes should be
connected to U, V, W
terminals directly and
separated from the
main output wires.
Long wiring here
might cause short
circuit failure.
Long wiring here might
cause SC level fluctuation
and malfunction.
Long GND wiring here might
generate noise to input signal and
cause IGBT to malfunction.
C2
C3
+
5V
MCU
5kΩ
15V
D1
C1
+
+
+
+
VUFB(2)
P(24)
U(23)
V(22)
W(21)
NU(20)
NV(19)
NW(18)
IGBT1
Di1
IGBT2
Di2
IGBT3
Di3
IGBT4
Di4
IGBT6
Di6
IGBT5
Di5
UP(5)
VWFB(4)
HVIC
M
LVIC
VVFB(3)
VP1(8)
VNC(9)
UN(10)
VN(11)
WN(12)
VN1(13)
VP(6)
WP(7)
VNC(16)
C1N(15)
VOT(17)
C4
A
B
C
D
C2
C1
R1
N1
CONTROL
GND WIRING
POWER
GND WIRING
SHUNT
RESISTOR
C2
D1
VD
FO(14)
Notes:
1) It is recommended to connect Control GND wiring and Power GND wiring only at point N1 (near terminal of shunt resistor) to prevent a malfunction by Power GND fluctuations.
2) It is recommended to insert a Zener diode D1 (24V/1W) between each pair of control supply terminals to prevent surge destruction.
3) To prevent surge destruction, the wiring between the DC bus smoothing capacitor and the P, N1 terminals should be as short as possible. Generally a 0.1-0.22µF snubber
capacitor C3 between the P-N1 terminals is recommended.
4) Time constant of R1, C4 for SC protection circuit should be selected so that protection works within 2µs. (Recommended value: ≤2µs) SC interrupting time might vary with the
wiring pattern. Tight tolerance, temp-compensated type, is recommended for R1, C4.
5) To prevent malfunction, the wiring of A, B, C should be as short as possible.
6) The point D at which the wiring to CIN filter is divided should be near the terminal of shunt resistor. NU, NV, NW terminals should be connected at near NU, NV, NW terminals.
7) All capacitors should be mounted as close to the terminals as possible. (C1: good temperature, frequency characteristic electrolytic type and C2: 0.22µ-2µF, good temperature,
frequency and DC bias characteristic ceramic types recommended.)
8) Input drive is active-high type. There is a 3.3kΩ (Min.) pull-down resistor in the input circuit of IC. To prevent malfunction, the wiring of each input should be as short as possible.
When using RC coupling circuit, make sure the input signal level meets the turn-on and turn-off threshold voltage.
9) FO output is open drain type. It should be pulled up to MCU or control power supple (e.g. 5V) by resistor makes IFO up to 1mA.
10) Direct coupling to the MCU without any opto-coupler or transformer isolation is possible because the HVIC is inside the module.
11) Two VNC terminals (9 & 16 pin) are connected inside the DIPIPM. Be sure to connect either one to the 15V power supply GND outside and leave the other one open.
12) IC malfunction can occur and cause the DIPIPM to operate erroneously when high frequency noise is superimposed on the control supply line. To avoid such problem, the line
ripple voltage should meet dV/dt ≤ ±1V/μs and Vripple ≤ 2Vp-p.
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
9
12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Protection Function Timing Diagrams
A1 A4
A5
A2
SC
A7
A3
SET RESET
RC CIRCUIT TIME CONTAINS
DELAY
SC REFERENCE VOLTAGE
A6
A8
N-SIDE
CONTROL INPUT
PROTECTION
CIRCUIT STATE
INTERNAL IGBT GATE
OUTPUT CURRENT IC
SENSE VOLTAGE OF
THE SHUNT RESISTOR
FAULT OUTPUT FO
Short-Circuit Protection (N-side only with the external shunt resistor and RC filter)
B1
B4
B5
B2
UVDt
B7
B3
SET RESETRESET
UVDr
B6
N-SIDE CONTROL INPUT
PROTECTION
CIRCUIT STATE
CONTROL SUPPLY
VOLTAGE VD
OUTPUT CURRENT IC
FAULT OUTPUT FO
Under-Voltage Protection (N-side, UVD)
A1: Normal operation – IGBT turn on and conducting current.
A2: Short-circuit current detected (SC trigger).
A3: All N-side IGBT gate hard interrupted.
A4: All N-side IGBTs turn off.
A5: FO output with a fixed pulse width of tFO(min) = 20µs.
A6: Input “L” – IGBT off.
A7: Input “H” – IGBT off in spite of “H” input.
A8: Normal operation – IGBT on and conducting current.
B1: Control supply voltage rise – After the voltage level reaches UVDr, the drive circuit begins to work
at the rising edge of the next input signal.
B2 : Normal operation – IGBT turn on and conducting current.
B3: Under-voltage trip (UVDt).
B4: All N-side IGBTs turn off regardless of the control input level.
B5: FO output during under-voltage period, however, the minimum pulse width is 20µs.
B6: Under-voltage reset (UVDr).
B7: Normal operation – IGBT turn on and conducting current.
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
10 12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Protection Function Timing Diagrams
Typical Interface Circuit
Pattern Wiring Around Shunt Resistor
C1
C4
C5
C2
UVDt
C6
C3
SET RESETRESET
HIGH LEVEL (NO FAULT OUTPUT)
UVDBr
P-SIDE CONTROL INPUT
PROTECTION
CIRCUIT STATE
CONTROL SUPPLY
VOLTAGE VDB
OUTPUT CURRENT IC
FAULT OUTPUT FO
Under-Voltage Protection (P-side, UVDB)
C1: Control supply voltage rises – After the voltage level reaches UVDBr, the drive circuit begins to work
at the rising edge of the next input signal.
C2: Normal operation – IGBT turn on and conducting current.
C3: Under-voltage trip (UVDBt).
C4: IGBT stays off regardless of the control input level, but there is no FO signal output.
C5: Under-voltage reset (UVDr).
C6: Normal operation – IGBT turn on and conducting current.
UP, VP, WP, UN, VN, WN
MCU
5V LINE
10kΩ
3.3kΩ (MIN)
FO
VNC (LOGIC)
DIPIPM
NOTE: RC coupling at each input
(parts shown dotted) may change
depending on the PWM control
scheme used in the application and
the wiring impedance of the printed
circuit board. The DIPIPM input signal
section integrates a 3.3kΩ (min)
pull-down resistor. Therefore, when
using an external filtering resistor, care
must be taken to satisfy the turn-on
threshold voltage requirement.
5kΩ
TEMPERATURE
SIGNAL
REF
INSIDE LVIC
OF DIPIPM
+
–
VNC
VOT
NOTE: VOT outputs the analog signal that is amplified signal of temperature detecting element on LVIC by inverting amplifier.
It is recommended to insert a 5kΩ pull down resistor to obtain linear output characteristics at lower temperature than room
temperature. When the pull down resistor is inserted between VOT and VNC (GND), the extra current calculated by VOT
output voltage/pull down resistance flows as additional LVIC circuit current continuously.
When the system controller supply is 3.3V, it is recommended to insert clamp Di between VCC (MCU supply) and VOT for
preventing over voltage destruction of the system controller.
MCU
PS219B4-S, PS219B4-AS, PS219B4-CS
Intellimod™ Module
Dual-In-Line Intelligent Power Module
15 Amperes/600 Volts
11
12/11 Rev. 0
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 www.pwrx.com
Pattern Wiring Around Shunt Resistor
External SC Protection Circuit Using Three Shunt Resistors
VNC
NV
NU N1
NW
DIPIPM
Wiring inductance should be less than 10nH.
(Equivalent to the inductance of a copper pattern with
length = 17mm and width = 3mm.)
NU, NV, NW should be connected near terminals.
RSHUNT GND wiring from VNC should be as
close to the shunt resistors as possible.
DRIVE CIRCUIT
DIPIPM
DRIVE CIRCUIT
PROTECTION CIRCUIT
NU
SHUNT
RESISTORS COMPARATORS
(Open Collector Output Type)
OR OUTPUT
NV
NW
W
V
U
P
P-SIDE
IGBTs
N-SIDE
IGBTs
VNC
Rf
CfVref
−
+
5V
CIN
A
C
D
B
Rf
CfVref
−
+
Rf
CfVref
−
+
Notes:
1) It is necessary to set the time constraint Rf, Cf of external comparator input so that the IGBT stops within 2μs when short circuit occurs.
SC interrupting time can vary with the wiring pattern, comparator speed and so on.
2) The threshold voltage Vref should be set up as the same rating as the short circuit trip level (VSC(ref), typically 0.48V).
3) Select the external shunt resistance so that the SC trip-level is less than specified value (≤1.7 times current rating).
4) Wiring A, B, and C should be as short as possible to avoid a malfunction.
5) Where the wiring to the comparator is divided, point D, should be near the shunt resistor terminal.
6) OR output high level should be over 0.53V (= maximum VSC(ref)).
