115 MHz Filter
6 MHz Bandwidth
Part Number SF0115BA03088S
Rev X6 15-Feb-05
Page 1 of 4
Integrated Circuit Systems • Surface Acoustic Wave Products
324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456
www.icst.com
QF12/3
Integrated
Circuit
Systems, Inc.
TYPICAL PERFORMANCE
Horizontal: 2.5 MHz/div Vertical (from top): Magnitude 10 dB/div
Magnitude 1 dB/div
Group Delay Deviation 150 ns/div
SPECIFICATION
Parameter Min Typ Max Units
All electrical specifications apply over the full -10ºC to +50ºC operating range and
include allowance for all manufacturing tolerances
Center Frequency FC 1 114.88 115 115.12 MHz
1 dB Bandwidth 2 5.6 6.08 MHz
3 dB Bandwidth 2 6.0 6.44 MHz
40 dB Bandwidth 2 7.75 8.2 MHz
Stopband Rejection, 25 MHz to 100 MHz 45 58 dB
Stopband Rejection, 130 MHz to 1000 MHz 45 53 dB
Minimum Insertion Loss 18.9 20 dB
Passband Amplitude Variation, FC ± 2.8 MHz 3 0.6 0.8 dB p-p
Passband Group Delay Variation, FC ± 2.8 MHz 100 150 ns p-p
Absolute Delay 2.0 2.1 µs
Input VSWR, FC ± 2.8 MHz 4 1.55 1.8 : 1
Output VSWR, FC ± 2.8 MHz 4 1.3 1.8 : 1
Maximum Input Level 20 dBm
Source and Load Impedance 50 Ω
Operating Temperature Range -10 +50 ºC
Storage Temperature Range -45 +85 ºC
Notes:
1. Defined as the mean of the 10dB frequencies.
2. dB levels are taken to be relative to the insertion loss.
3. Excludes final roll-offs to the 1dB points. Note that ‘Passband Amplitude Variation’
includes Ripple (fast variations) and Slope (slow variations).
4. When matched as indicated on Page 3.
115 MHz Filter
6 MHz Bandwidth
Part Number SF0115BA03088S
Rev X6 15-Feb-05
Page 2 of 4
Integrated Circuit Systems • Surface Acoustic Wave Products
324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456
www.icst.com
QF12/3
Integrated
Circuit
Systems, Inc.
DESCRIPTION
1,2,3,4,6,7,8,9
PIN NO.
INPUT
OUTPUT
GROUND
NOTES:
DIMENSIONS SHOWN ARE NOMINAL IN
MILLIMETERS. ALL TOLERANCES ARE
±0.15MM EXCEPT OVERALL LENGTH
AND WIDTH
5
10
PACKAGE AND SUGGESTED PCB FOOTPRINT
MARKING
Package Material:
Body: Al2O3 ceramic
Lid: Kovar, Ni plated
Terminations: Au plating 0.5-1.0 um,
over a 2-6 um Ni plating
ICS
BA03088S
19.00+0.20
-0.10
6.50+0.20
-0.10
1.02
1.91
INDEX MARK
1.59
.61
1.96 MAX
12 3 4 5
10 9 8 7 6
12345
10 9 8 7 6
YYJJJM
8.51
8.74
1.90
1.12
2.66
SUGGESTED PCB FOOTPRINT
PACKAGE INFORMATION
The date code consists of:
YY = last two digits of year; JJJ = Julian day;
M = manufacturing site code
12345
10 9 8 7 6
ICS
BA03088S
YYJJJM
LOGO
MARKING CODE
ESD PIN 1
115 MHz Filter
6 MHz Bandwidth
Part Number SF0115BA03088S
Rev X6 15-Feb-05
Page 3 of 4
Integrated Circuit Systems • Surface Acoustic Wave Products
324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456
www.icst.com
QF12/3
Integrated
Circuit
Systems, Inc.
MATCHING CIRCUIT
Component values in 50: Rp1 = 430 Ls1 = 68 nH Cp1 = 56 pF
(Minimum inductor Q = 45) Rp2 = 300 Ls2 = 68 nH Cp2 = 56 pF
Notes:
1. Optimum values may differ from these when using a different fixture or board layout. The values shown here
are intended as a guide only.
2. Required component tolerances – resistors ±5%, inductors ±2%, capacitors ±5%.
MAXIMUM RATINGS
Parameter Min Max Units
Operating Temperature Range -10 +50 ºC
Storage Temperature Range -45 +85 ºC
Input Power Level 20 dBm
D. C. Voltage between Each Terminal 15 V
Ls1
Cp1 Rp1 Cp2
Rp2
Ls2
10 5
1,2,3,4,6,7,8,9
115 MHz Filter
6 MHz Bandwidth
Part Number SF0115BA03088S
Rev X6 15-Feb-05
Page 4 of 4
Integrated Circuit Systems • Surface Acoustic Wave Products
324 Clark Street, Worcester, MA 01606, USA • Phone 508-852-5400 • Fax 508-852-8456
www.icst.com
QF12/3
Integrated
Circuit
Systems, Inc.
PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
Parameter Qualification Conditions
Life Testing High temperature bake at +85 ºC for 168 hours.
Temperature Cycling
MIL-STD 883, Method 1010:
-40 ºC to +85 ºC, 10 cycles, 10 minutes dwell at
temperature extremes
Vibration
MIL-STD-202, Method 201A:
10 to 55 Hz, double amplitude of 0.06” for 2 hours in each
axis.
Mechanical Shock MIL-STD-883, Method 2002, Test Condition B:
1500 g, 3 impacts each axis
Solder Heat Resistance and Reflow
Condition
Peak temperature 240+/-5 ºC for 10 seconds.
Pre-heat: 150-170 ºC for 60 to 90 seconds.
Peak dwell: over 200 ºC for 23 to 26 seconds.
Handling: Class 1 per MIL-STD-1686
Reflow Profile is shown at the bottom of this table.
Lead Integrity MIL-STD 883 Method 2004, Condition D
8 oz for 30 seconds.
Solderability MIL-STD-883 Method 2003:
245 ºC +/-5 ºC; 95% coverage; no steam aging
Hermeticity MIL-STD 883 Method 1014:
Condition A2 and Condition C (no bomb)
ESD Classification Class I per MIL-STD-883 Method 3015
Precautions Do not subject devices to ultrasonic cleaning, which may
cause deterioration and destruction of the device.
Reflow Profile
0
50
100
150
200
250
0 50 100 150 200 250 300
TIME (sec)
TEMP (deg C)
ISO 9001
Registered
