Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type TC SERIES: The TC Series is designed for hybrid circuit and low profile printed circuit board applications where inductance is to be minimized, or where substrate space is at a premium. They can be attached to substrates or circuit boards by dipsoldering, welding, re-flow soldering or other conventional methods. These units have the further advantage of being compatible with automatic assembly equipment-minus the problems associated with flexible terminal lead wires. Our chip tantalums meet all EIA sizes. RATINGS Capacitance Range: Tolerance Range: Rated Voltage: 0.1F to 220F M(20%), K(10%) 4V to 50V ITEMS SPECIFICATIONS, PERFORMANCE Operating Temperature Range -55C~+85C(+125C) Maximum Working Temperature +85C (+125C with derating) Rated Voltage Range 4 VDC ~ 50 VCD Capacitance Range 0.1F ~ 220F Standard Capacitance Tolerance 20% (M) 10%(K) Dissipation factor (tan ) JIS-C-5102 20C 120Hz JIS-C-5102 20C 120Hz Max. Leakage Current Max 12% 0.1 ~ 1.0F 6.0% 1.5 ~ 100F 8.0% NA Max. 15% 0.1 ~ 1.0F 6.0% 1.5 ~ 100F 8.0% 0.125CV or 6.25A whichever is greater -55C +125C Surge Voltage Solder Heat Resistance JIS-C-5102 20C (5 minutes) (after rated voltage applied) Max. tan C Stability Failure Rate at 85C 6.0% Temp. Temperature High Temperature Test 4.0% 1.5~100F See Table of Standard Ratings Not more than 0.01CV or 0.5A, whichever is greater Leakage Current Humidity Test 0.1~1.0F TEST CONDITIONS Capacitance Change Dissipation Factor Leakage Current Less than 5% Less than specified value Procedure: 1. 202C 2. -55+0-3C Stabilized 3. 202C 15 min. 4. +125+3 C 2 hrs. -0 JIS-C-5140 and 5102 85C Surge voltage applied, 1000 times with series resistance of 1000 for 30 seconds at intermittent intervals of 5 minutes Withstand solder immersion 5 seconds at 260C or reflow 10 seconds at 260C Capacitance Change Dissipation Factor Leakage Current Capacitance Change Dissipation Factor Leakage Current Less than 5% Less than initial specified value Less than 10% Less than initial specified value 1% per 1,000 hours JIS-C-5102 at 60C humidity 90% ~ 95% RH, 500 Hours JIS-C-5102 85C, Rated voltage 2000 hours or 125C Derating voltage 1000 hours with circuit resistance of 1/V MTBF 5 X 104 Hr. 31 Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type Ordering Information & Marking Ordering Information Example: 1 MFD 16 volt 20% TC M IC 105 A T Series Destination Capacitance Tolerance Rated Voltage Capacitance Size Taping & Packaging Capacitance Tolerance 20% 10% Code M K Rated Voltage 2 4 6.3 10 16 20 25 35 50 Code OD OG OJ IA IC ID IE IV IX Capacitance (ex) 0.1 ~ 0.68F 1.0 ~ 6.8F 10 ~ 470F Code 104 ~ 684 105 ~ 685 106 ~ 477 R: Decimal Point - First two digits represent significant figures and the third digit specifies number of zeros to follow. Capacitance unit is F. MARKING ex) 6.3V-2.2F A - Size Capacitance: First two digits represent capacitance and the third digit specifies number of zeros to follow. ex) 10V-22F Capacitance unit is F. B, C, D - Size Note: See back cover for low ESR information 32 FREQUENCY CHARACTERISTIC CURVES (TC SERIES) Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type STANDARD RATINGS AND CASE SIZE DISTRIBUTION* Rated Voltage @ +85C 4 6.3 10 16 20 25 35 50 Surge Voltage @ +85C 5.2 8 13 20 26 32 46 65 Derated Voltage @ 125C 2.7 4 7 10 13 17 23 33 Derated Surge Voltage @ +125C 3.4 5 9 12 16 22 28 40 STD/EXT STD/EXT STD/EXT STD/EXT STD/EXT STD/EXT STD/EXT STD/EXT A A A A B/A B/A B/A C/B C/B C D/C D/ D D/E /E A B/A B B C/B C C /C D/C D/ D D/E Capacitance F 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 A A A A B/A B/A C/B C/B C/B D/C D/ D/ E A A A /A B/A B/A A/C/B A/C/B B/C D/C/B D/ D/C D/E C/D/E A A A /A B/A B/A C/B/A D/C/B D/C/B D/C/B D/C /D E/D D/E D/E A A A A B/A B/A C/B/A C/B C/B C/B D/C/B D/C/B /D E/D E/D A A A /A B/A C/B C/B C/B D/C/B D/C D/C /D D/E /E A A A B/A B/A C/B C/B C/B D/C D/C D/C D/C E/D E *Letter code after / indicates new extended range. Please indicate size code on ordering. NOTES 1. Be sure polarity. Positive (+) side has white belt. 2. For cleaning, freon(R) TE, TES and TMS are recommended at a temperature less than 50C for a period less than 5 minutes. 3. When ultrasonic cleaning is necessary, fixing capacitor body by epoxy adhesive before soldering is recommended. Establish adequate cleaning conditions by experiment to avoid damaging capacitor terminations. 4. Limit reverse voltage to 1.0V or less than 5% of rated voltage whichever is smaller. 5. In case of low impedance circuit use (Less than 3 /V), adequate voltage derating is recommended to improve M.T.B.F. 6. In case of automatic mounting, the tweezer pressure shall be less than 500 grams and should not exceed 5 seconds. 33 Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type MAX ESR () @ 100kHz, +25C / BY VALUE AND CASE SIZE VW (VC) 6.3 10 16 20 25 MAX RIPPLE CURRENT (Arms) @ 100kHz, +25C / BY VALUE AND CASE SIZE VW (VC) 35 50 0.1 A 24.0 A 22.0 0.15 A 21.0 0.22 A 18.0 A 20.0 B 17.0 B 14.0 A 15.0 B 12.0 A 12.0 B 10.0 A 9.0 B 8.0 B 6.5 B 10.0 C 8.0 C 7.5 0.47 C 5.5 1.0 B 5.2 C 4.5 C 4.0 1.5 C 3.5 D 2.5 D 2.0 2.2 3.3 D 1.4 E 1.2 CAP (F) 4.0 0.33 0.47 A 14.0 0.68 A 12.0 A 10.0 A 11.0 A 10.0 A 10.0 A 8.0 A 7.5 A 9.0 B 7.0 B 5.5 A 9.0 A 7.5 A 7.0 B 5.5 A 6.2 B 4.4 B 3.6 B 5.0 B 4.5 B 3.8 B 3.6 C 2.8 C 2.4 1.0 1.5 2.2 3.3 A 9.0 A 7.5 A 6.5 4.7 A 7.5 A 6.5 6.8 A 6.5 A 6.0 B 4.0 B 3.5 A 6.0 B 4.0 B 3.5 A 6.0 B 4.0 B 3.5 10 15 B 3.2 C 2.5 B 2.4 C 2.2 C 1.8 22 33 47 68 100 C 1.6 D 1.1 D 0.9 150 D 0.7 220 E 0.6 B 3.2 C 2.5 B 2.4 C 2.2 B 2.0 C 1.8 C 1.6 D 1.1 D 0.9 D 0.8 D 0.6 E 0.6 D 0.7 E 0.6 B 3.2 C 2.5 B 2.4 C 2.2 B 2.5 C 1.8 C 1.6 D 1.1 C 1.6 D 0.9 D 0.8 D 0.7 E 0.7 D 0.8 E 0.6 D0.9 E 0.6 B 3.3 C 2.6 B 2.4 C 2.2 C 1.8 B 2.3 C 1.6 D 1.1 C 1.2 D 0.9 D 0.8 D 0.7 E 0.8 D 0.7 E 0.7 B 3.5 C 2.8 C 2.4 C 2.0 D 1.3 C 1.7 D 1.1 C 1.5 D 0.9 D 0.8 D 0.7 E 0.9 E 0.6 C 2.0 D 1.4 C 1.8 D 1.2 D 1.0 D 0.8 C 3.5 C 2.5 C 2.2 D 1.5 D 1.3 35 50 0.1 A0.054 A0.056 0.15 A0.058 0.22 A0.062 A0.059 B0.069 B0.076 0.33 A 0.068 B0.076 B0.082 A0.076 B0.089 B0.089 C0.117 A0.084 A0.088 C0.121 B0.100 A0.088 B0.111 C0.141 B0.107 B0.121 B0.124 C0.166 C0.156 C0.177 B0.133 C0.177 D0.249 B0.149 C0.210 D0.274 C0.198 C0.214 C0.224 D0.327 D 0.316 C0.235 D0.340 E0.371 D0.327 C 0.247 D0.387 D0.354 D0.387 E0.454 CAP (F) 4.0 6.3 10 16 20 A0.071 A0.076 0.68 A0.080 A0.084 A0.084 A0.094 A0.097 A0.088 A0.097 B0.126 A0.088 A0.097 A0.104 4.7 A0.097 A0.104 6.8 A0.104 A0.108 B0.141 B0.151 A0.108 B0.141 B0.151 B0.100 B0.121 A0.106 B0.135 B0.149 D 1.0 10 E 0.8 15 E 0.7 22 E 0.7 33 E 0.9 47 68 100 25 A0.108 B0.141 B0.151 B0.158 C0.210 B0.183 C0.224 C0.247 C0.262 D0.369 D0.408 150 D0.463 220 E0.524 B0.145 B0.151 C0.198 C0.214 B0.156 C 0.206 B0.158 B 0.183 C0.235 C0.210 C 0.224 D0.340 B0.158 B0.183 C0.247 C0.254 C0.210 C0.224 D0.369 B0.183 BO.208 CO.277 D0.433 B0.35 C0.262 C0.224 C0.247 D0.369 D0.408 BO.208 C0.262 CO.277 D0.433 E0.486 C0.247 D0.369 D0.408 C0.262 CO.277 D0.433 D0.486 EO.524 D0.369 D0.408 EO.454 D0.408 D0.433 D0.463 E0.486 E0.454 D0.8 D0.462 DO.463 E0.486 E0.486 DO.486 DO.524 E0.524 E0.524 E0.524 E0.524 D0.486 D0.524 E0.486 Dimensions in mm 34 EIA Case Code L 0.2 W 0.2 H 0.2 P 0.3 a 0.2 h(min) A(3216) 3.2 1.6 1.7 0.8 1.2 0.7 B(3528) 3.5 2.8 1.9 0.8 2.2 0.7 C(6032) 6.0 3.2 2.5 1.3 2.2 1.0 D(7343 7.3 4.3 2.9 1.3 2.4 1.0 E(7343H) 7.3 4.3 4.0 1.3 2.4 1.0 Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type CHARACTERISTIC DATA & CURVES Frequency Dependence of the Permissible Superimposed AC Voltage Effect of Circuit Impedance on the Failure Rate LOAD LIFE CHARACTERISTIC CURVES (TC SERIES) Effect of the Applied Voltage and Ambient Temperature on the Failure Rate TEMPERATURE CHARACTERISTIC CURVES (TC SERIES) Immersion Method Reflow Method 35 Cal-Chip Electronics, Incorporated TC SERIES TC Series Tantalum Solid Electrolytic Capacitors - Resin Molded Chip Type, Standard Type TAPING SPECIFICATIONS Dimensions in mm Embossed Plastic Tape per EIA-481-1 EIA SIZE 3216 3528 6032 7343 7343H CASE CODE A B C D E Ao0.2 Bo0.2 W F P D1 B1 KMAX 1.9 3.1 3.9 4.7 4.7 3.9 3.9 6.3 7.7 7.7 8.0.30 8.0.30 12.0.30 12.0.30 12.0.30 3.5.05 3.50.5 5.5.05 5.5.05 5.5.05 4.0 4.0 8.0 8.0 8.0 1.0 1.0 1.5 1.5 1.5 4.2 4.2 8.2 8.2 8.2 2.4 2.4 4.5 4.5 4.5 TAPE SIZE 8mm 8mm 12mm 12mm 12mm QUANTITY PER REEL 7" REEL 13" REEL 2000 9000 2000 8000 500 3000 500 2500 500 2500 STANDARD ORIENTATION Standard reel diameter is 7" and 13" reels are available on special order with (13) added to the end of the part number. Cover tape peel-off specification 1. Peel-off speed: 300 mm/min. 2. Peel-off force: F = 30 - 75g 3. Peel-off angle: = 0 - 15 36