VMMK-3603
1 - 6 GHz Positive Gain Slope Low Noise Amplifier in SMT Package
Data Sheet
Description
The VMMK-3603 is a small and easy-to-use, broadband,
positive gain slope low noise amplifier operating in various
frequency bands from 1 to 6 GHz with typical noise figure
of 1.4 dB. It is housed in the Avago Technologies’ industry-
leading and revolutionary sub-miniature chip scale
package (GaAsCap wafer scale leadless package) which is
small and ultra thin yet can be handled and placed with
standard 0402 pick and place assembly equipment. The
VMMK-3603 provides a typical gain of 17 dB with good
linearity of +25 dBm typical OIP3 and input and output
return losses. It can be operated from 3 V to 5 V power
supply. It is fabricated using Avago Technologies unique
0.25 μm E-mode PHEMT technology which eliminates the
need for negative gate biasing voltage.
WLP0402, 1 mm x 0.5 mm x 0.25 mm
Attention: Observe precautions for
handling electrostatic sensitive devices.
ESD Machine Model = 50 V
ESD Human Body Model = 300 V
Refer to Avago Application Note A004R:
Electrostatic Discharge, Damage and Control.
Pin Connections (Top View)
Note:
“M” = Device Code
“Y” = Month Code
Features
• 1 x 0.5 mm surface mount package
• Ultrathin (0.25 mm)
• Wide frequency range: 1 to 6 GHz
• Low noise figure
• Positive gain slope
• Self-Biasing: 3 to 5 V
Specifications (5 GHz, Vdd = 5 V, Zin = Zout = 50 Ω)
• Small signal gain: 17 dB typ.
• Noise Figure = 1.5 dB typ.
• Output 3rd Order Intercept Point = 25 dBm
Applications
• 2.4, 3.5, and 5-6 GHz WLAN and WiMax
• 802.16 & 802.20 BWA systems
• Radar and ECM systems
• Generic IF amplifier
MY
MY OutputInput
Input Output
Amp
2
Electrical Specifications
Table 1. Absolute Maximum Rating [1]
Symbol Parameters/Condition Unit Absolute Max
Vd Supply Voltage (RF Output) [2] V8
Id Supply Current [2] mA 56
Pin, max CW RF Input Power (RF Input) [3] dBm 15
Pdiss Total Power Dissipation mW 460
Tch Max Channel Temperature °C +150
θjc Thermal Resistance [4] °C/W 95.3
Notes
1. Operation of this device above any one of these parameters may cause permanent damage
2. Bias is assumed DC quiescent conditions
3. With the DC (typical bias) and RF applied to the device at board temperature Tb = 25° C
4. Thermal resistance is measured from junction to board using IR method
Table 2. DC and RF Specifications [1]
TA = 25° C, Vd = 5 V, Freq = 5 GHz, Zin = Zout = 50 Ω (unless otherwise specified)
Symbol Parameters/Condition Unit Minimum Typical Maximum
Id [2] Supply Current mA 27 36 44
NF [2,3] Noise Figure dB 1.5 1.9
Ga [2,3] Associated Gain dB 15.5 16.8 19.5
S11 [4] Input Return Loss dB -11
S22 [4] Output Return Loss dB -11
OIP3 [4,5] Output 3rd Order Intercept Point dBm 25
Notes
1. Losses of the test system have been de-embedded from final data
2. Measured data obtained from wafer-probing using a G-S, S-G pyramid probe
3. NF and Ga obtained from Noise Figure Meter
4. S-parameters and OIP3 data obtained using 300 μm G-S-G probing on PCB substrate
5. OIP3 test condition: Center frequency = 5 GHz, 2 tone offset = 10 MHz, Pin = -25 dBm
3
Product Consistency Distribution Charts at 5.0 GHz, Vd = 5 V
Id @ Vd = 5 V, Mean = 36 mA, LSL = 27 mA, USL = 44mA NF @ 5 GHz, Mean = 1.5 dB, USL = 1.9 dB
Gain @ 5GHz, Mean = 16.8 dB, LSL = 15.5 dB, USL = 19.5 dB
(Data obtained using Noise Figure Analyzer)
Notes:
Distribution data based on 65 Kpcs part sample size from MPV lots.
Future wafers allocated to this product may have nominal values
anywhere between the upper and lower limits.
1.91.7 2.1120.9 1.31.1 1.5
LSL USL
USLLSL
USL
0.023 0.025 0.032 0.036 0.04 0.044 0.048
2018 19171615
4
VMMK-3603 Typical Performance
TA = 25° C, Zin = Zout = 50 Ω; biasing by a broadband bias tee; S-param data obtained using 300 μm GSG probing on PCB
substrate, NF, IP3, and P1dB obtained using eval board; losses calibrated out to the package reference plane.
Figure 1. Small Signal Gain Over Bias Figure 2. Input Return Loss Over Bias
Figure 3. Output Return Loss Over Bias Figure 4. NF Over Bias
Figure 5. OIP3 Over Bias Figure 6. OP1dB Over Bias
0.0
3.0
6.0
9.0
12.0
15.0
18.0
21.0
012345678910
Frequency (GHz)
S21 (dB)
-15.0
-12.0
-9.0
-6.0
-3.0
0.0
012345678910
Frequency (GHz)
S11 (dB)
-30.0
-27.0
-24.0
-21.0
-18.0
-15.0
-12.0
-9.0
-6.0
-3.0
0.0
012345678910
Frequency (GHz)
S22 (dB)
0.8
1
1.2
1.4
1.6
1.8
2
01234567
Frequency (GHz)
NF (dB)
10
15
20
25
30
123456
Frequency (GHz)
OIP3 (dBm)
4
7
10
13
16
123456
Frequency (GHz)
P1dB (dBm)
3 V
4 V
5 V
3 V
4 V
5 V
3 V
5 V
3 V
5 V
3 V
5 V
3 V
4 V
5 V
5
VMMK-3603 Typical Performanc
Vd = 5 V unless noted, Zin = Zout = 50 Ω, biasing by a broadband bias tee; over temp data obtained using eval board;
losses calibrated out to the package reference plane.
Figure 7. Id vs. Vd over Temp Figure 8. Gain over Temp
Figure 9. NF Over Temp Figure10. OIP3 Over Temp
Figure 11. OP1dB Over Temp
10
15
20
25
30
35
40
45
23456
Vd (Volts)
Id (mA)
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
01234567
Frequency (GHz)
NF (dB)
4
7
10
13
16
123456
Frequency (GHz)
P1dB (dBm)
14
15
16
17
18
123456
Frequency (GHz)
S21(dB)
15
20
25
30
35
123456
Frequency (GHz)
OIP3 (dBm)
25° C
-40° C
+85° C
25° C
-40° C
+85° C
25° C
-40° C
+85° C
25° C
-35° C
+85° C
25° C
-40° C
+85° C
6
Typical Scattering Parameters
TA = 25° C, Vd = 3 V, Zin = Zout = 50 Ω unless noted. Data obtained using 300 μm G-S-G PCB substrate & broadband bias
tees, losses calibrated out to the package reference plane.
Freq
GHz
S11 S21 S12 S22
dB mag Phase dB mag phase dB mag phase dB mag Phase
0.05 -0.2 0.977 -4.8864 19.2 9.153 -179.6516 -38.2 0.0123 91.3266 -7.7 0.4127 0.6165
0.1 -0.3 0.9706 -9.9273 19.3 9.2677 176.9829 -35.4 0.0169 75.7197 -7.3 0.431 -6.0822
0.2 -0.6 0.931 -19.6121 19.2 9.1431 170.3651 -30.1 0.0312 66.652 -7.4 0.4254 -17.5835
0.3 -1.2 0.8726 -28.1505 18.9 8.8217 165.3938 -27.3 0.0432 57.1804 -8.0 0.3971 -27.3636
0.4 -1.8 0.8098 -35.3755 18.5 8.4556 161.4364 -25.5 0.0533 48.1187 -8.8 0.3638 -35.3407
0.5 -2.5 0.7468 -41.2905 18.2 8.1299 158.4159 -24.3 0.061 40.9588 -9.6 0.3308 -41.8528
0.6 -3.1 0.701 -41.9333 17.6 7.5629 156.9294 -23.8 0.0645 35.7729 -9.8 0.3233 -37.1208
0.7 -3.7 0.6527 -45.824 17.3 7.3442 154.9164 -23.3 0.0687 30.5102 -10.6 0.2959 -40.3919
0.8 -4.3 0.6098 -49.2059 17.1 7.1755 153.0505 -22.8 0.0723 25.8161 -11.4 0.2699 -42.9121
0.9 -4.9 0.5718 -52.08 16.9 7.0187 151.3266 -22.5 0.0746 21.5702 -12.1 0.2487 -44.9453
1 -5.4 0.5385 -54.7877 16.8 6.9197 149.6624 -22.3 0.0767 18.0463 -12.9 0.2273 -46.2074
1.5 -7.5 0.4229 -65.4212 16.4 6.6173 141.4379 -21.8 0.0816 4.0387 -16.4 0.1522 -49.2137
2 -9.0 0.3552 -75.7226 16.3 6.5474 132.6275 -21.6 0.0831 -6.4352 -20.2 0.0975 -47.4521
2.5 -10.2 0.308 -81.3963 16.4 6.5943 123.4518 -21.6 0.0828 -14.7788 -22.4 0.0759 -43.3979
3 -11.3 0.2738 -91.3794 16.5 6.7138 113.3991 -21.8 0.0817 -22.0721 -26.7 0.0461 -22.5111
3.5 -12.1 0.2493 -103.0569 16.8 6.8955 102.6078 -21.9 0.0804 -29.1338 -26.9 0.045 26.9498
4 -12.6 0.2339 -115.7385 17.0 7.1158 90.9712 -22.0 0.0794 -35.6715 -22.3 0.0767 53.6397
4.5 -12.7 0.2322 -129.9118 17.4 7.3808 78.2102 -22.2 0.0778 -42.3765 -18.1 0.1244 59.6162
5 -12.2 0.2468 -145.5479 17.7 7.64 64.0695 -22.3 0.0765 -49.1329 -14.7 0.1836 56.8991
5.5 -10.9 0.2852 -160.1544 17.9 7.8875 48.8364 -22.6 0.0744 -55.7584 -12.1 0.2475 49.0542
6 -9.1 0.3497 -178.3697 18.1 7.9936 31.1873 -22.8 0.0726 -63.9077 -9.9 0.3195 39.2463
7 -5.5 0.5303 142.0171 17.2 7.2517 -8.7294 -23.8 0.0648 -82.9034 -7.1 0.4402 12.7602
8 -3.4 0.6782 104.6622 14.5 5.3295 -45.6505 -26.1 0.0494 -101.8767 -6.7 0.4647 -14.159
9 -2.5 0.7529 74.4856 10.8 3.4774 -73.6841 -29.1 0.035 -114.8967 -7.3 0.4338 -32.6621
10 -2.0 0.7925 51.7086 7.1 2.2691 -94.1122 -32.3 0.0242 -124.2559 -7.9 0.4012 -46.0125
11 -1.7 0.8225 33.4831 3.7 1.5278 -109.423 -36.0 0.0158 -131.9905 -8.5 0.3765 -55.8495
12 -1.5 0.8456 17.4077 0.6 1.069 -121.8166 -40.8 0.0091 -139.6964 -8.7 0.3655 -63.6328
13 -1.2 0.8722 4.7204 -2.5 0.7536 -131.9503 -53.2 0.0022 -142.2453 -8.7 0.3686 -70.3725
14 -1.1 0.8802 -7.1979 -5.1 0.5578 -140.5919 -54.0 0.002 0.5436 -8.6 0.3709 -77.0036
15 -1.0 0.8961 -17.3162 -7.5 0.4238 -148.3565 -50.2 0.0031 6.8353 -8.5 0.3737 -84.129
16 -0.8 0.9118 -27.6757 -9.7 0.3259 -155.8471 -42.0 0.0079 19.5505 -8.3 0.3841 -91.3885
17 -0.7 0.9244 -37.4873 -11.9 0.2546 -163.0428 -39.9 0.0101 15.9588 -8.1 0.3922 -97.2096
18 -0.6 0.9282 -46.3774 -14.0 0.199 -169.2785 -36.9 0.0143 2.392 -7.9 0.402 -103.6084
19 -0.6 0.9369 -55.4445 -15.9 0.1606 -174.9897 -37.6 0.0132 -10.438 -7.7 0.4107 -108.8462
20 -0.6 0.9385 -63.2833 -17.8 0.1288 178.771 -37.1 0.0139 -8.8364 -7.6 0.4181 -113.2307
21 -0.5 0.9455 -71.189 -19.9 0.1012 173.6276 -34.7 0.0185 -18.2437 -7.4 0.425 -117.8475
22 -0.5 0.9461 -77.8723 -21.3 0.0861 169.4539 -36.6 0.0148 -34.0351 -7.3 0.4314 -122.2301
23 -0.4 0.9518 -84.7844 -22.9 0.0718 162.3099 -37.7 0.013 -25.5129 -7.2 0.4363 -125.4319
24 -0.4 0.9516 -91.3249 -25.1 0.0555 157.727 -35.3 0.0171 -31.2849 -7.2 0.4362 -128.9087
25 -0.4 0.9543 -97.0884 -26.0 0.0504 150.9037 -38.6 0.0117 -36.8647 -7.2 0.4361 -132.6289
7
Typical Scattering Parameters
TA = 25° C, Vd = 5 V, Zin = Zout = 50 Ω unless noted. Data obtained using 250 μm G-S-G PCB substrate & broadband bias
tees, losses calibrated out to the package reference plane.
Freq
GHz
S11 S21 S12 S22
dB mag Phase dB mag phase dB mag phase dB mag Phase
0.05 -0.2 0.9765 -5.3473 19.8 9.7378 179.865 -41.0 0.0089 101.6421 -7.2 0.4351 -3.1298
0.1 -0.3 0.969 -10.4315 19.8 9.7954 176.3417 -35.4 0.0169 76.4418 -7.1 0.4395 -7.9442
0.2 -0.7 0.9274 -20.7156 19.6 9.6011 169.8445 -30.3 0.0305 65.854 -7.5 0.424 -18.0476
0.3 -1.2 0.8665 -29.613 19.3 9.2449 164.9479 -27.5 0.0423 55.4655 -8.1 0.3922 -26.6857
0.4 -1.9 0.8011 -37.1751 18.9 8.8561 161.1065 -25.8 0.0514 46.9769 -9.0 0.356 -33.6356
0.5 -2.6 0.7382 -43.3115 18.6 8.5166 158.0882 -24.7 0.0585 39.3595 -9.9 0.32 -39.0593
0.6 -3.2 0.692 -44.0449 18.0 7.9383 156.6006 -24.3 0.0613 33.9254 -10.0 0.3153 -33.3994
0.7 -3.8 0.6439 -48.1284 17.8 7.7203 154.5257 -23.8 0.0649 28.7538 -10.8 0.2874 -35.3222
0.8 -4.4 0.602 -51.7328 17.6 7.5547 152.582 -23.3 0.0682 24.1196 -11.6 0.2621 -36.6951
0.9 -5.0 0.565 -54.8713 17.4 7.3962 150.7578 -23.0 0.0706 19.7084 -12.4 0.2411 -37.3403
1 -5.5 0.5331 -57.8302 17.3 7.2968 148.9784 -22.8 0.0722 16.1648 -13.1 0.2204 -37.2186
1.5 -7.4 0.4246 -70.3244 16.9 6.9736 140.009 -22.3 0.0763 1.6183 -16.3 0.1525 -31.3163
2 -8.8 0.3619 -83.2252 16.7 6.854 130.4826 -22.2 0.0772 -9.1633 -18.8 0.1143 -16.0481
2.5 -10.0 0.3174 -92.634 16.7 6.8325 120.5905 -22.3 0.0768 -18.3171 -18.9 0.1135 -5.6824
3 -10.9 0.2844 -106.7897 16.7 6.8564 110.0668 -22.5 0.0749 -26.6003 -18.5 0.1195 10.6561
3.5 -11.6 0.263 -123.054 16.8 6.9151 99.0187 -22.7 0.0732 -33.7451 -17.0 0.142 21.9712
4 -12.0 0.2502 -140.3754 16.9 6.9917 87.4663 -23.0 0.071 -40.969 -15.1 0.1751 27.5352
4.5 -12.0 0.2507 -158.2552 17.0 7.0797 75.2214 -23.3 0.0685 -48.1875 -13.3 0.2151 28.9598
5 -11.6 0.2633 -176.0757 17.1 7.1631 62.193 -23.6 0.0658 -55.6692 -11.6 0.2629 27.4716
5.5 -10.8 0.2877 169.4924 17.2 7.2488 48.8057 -24.1 0.0622 -62.7037 -10.0 0.3145 22.774
6 -9.6 0.3314 154.7483 17.2 7.2799 33.8787 -24.6 0.0589 -70.5383 -8.6 0.3699 16.8808
7 -6.7 0.4614 127.6033 16.9 6.9966 0.4678 -25.9 0.0507 -87.777 -6.4 0.4766 -0.4897
8 -4.1 0.6221 100.0949 15.4 5.8749 -35.6531 -28.3 0.0383 -108.0513 -5.5 0.5292 -22.568
9 -2.6 0.7394 72.7048 12.4 4.1718 -68.1977 -31.9 0.0255 -123.9911 -5.9 0.5066 -40.9205
10 -1.9 0.7993 50.3166 8.9 2.7894 -93.3719 -36.4 0.0151 -135.8243 -6.7 0.4642 -54.412
11 -1.6 0.8348 32.1122 5.4 1.8683 -112.2912 -42.3 0.0077 -149.8587 -7.4 0.4279 -63.6579
12 -1.3 0.8576 16.1694 2.2 1.2907 -127.1685 -52.8 0.0023 174.2257 -7.8 0.4092 -70.3075
13 -1.1 0.8829 3.6129 -0.9 0.8968 -139.2016 -46.6 0.0047 47.2364 -7.8 0.4073 -75.9325
14 -1.0 0.8885 -8.2264 -3.7 0.6537 -149.3954 -42.9 0.0072 28.2504 -7.8 0.4067 -81.6577
15 -0.9 0.9029 -18.1508 -6.2 0.4898 -158.4144 -41.6 0.0083 19.5155 -7.8 0.4089 -87.9
16 -0.7 0.9173 -28.4392 -8.6 0.3727 -167.162 -38.0 0.0126 19.2396 -7.6 0.4188 -94.5239
17 -0.6 0.9284 -38.1504 -10.8 0.2876 -175.4717 -36.5 0.015 15.2695 -7.4 0.4264 -99.7235
18 -0.6 0.9313 -46.9227 -13.0 0.2227 176.9209 -34.8 0.0183 4.0748 -7.2 0.4356 -105.7808
19 -0.5 0.9389 -55.9194 -15.0 0.1778 170.0955 -35.3 0.0171 -7.7662 -7.1 0.4435 -110.7482
20 -0.5 0.9399 -63.6621 -17.0 0.1416 162.632 -35.3 0.0171 -8.2348 -6.9 0.4507 -114.8575
21 -0.5 0.946 -71.499 -19.2 0.1101 155.5804 -33.6 0.021 -16.9273 -6.8 0.4566 -119.3594
22 -0.5 0.9467 -78.2123 -20.7 0.092 150.8211 -35.3 0.0171 -30.2145 -6.7 0.4632 -123.5707
23 -0.4 0.9515 -85.0468 -22.3 0.0767 142.117 -36.1 0.0156 -25.443 -6.6 0.4678 -126.9413
24 -0.4 0.9513 -91.568 -24.6 0.0589 134.4502 -34.3 0.0193 -32.1079 -6.6 0.4674 -130.3008
25 -0.4 0.9531 -97.3009 -25.5 0.0531 127.8596 -37.2 0.0138 -33.6267 -6.6 0.4662 -134.0917
8
Figure 14. Biasing the VMMK-3603
Figure 12. Evaluation/Test Board (available to qualified customers upon
request)
VMMK-3603 Applications and Usage Information
Table 3. VMMK-3603 Demo Board BOM
Component Value
DUT VMMK-3603
C1 100 pF
C2 8.2 pF
C5 0.1 μF
C6 100 pF
R1 820 Ohms
R2 10 Ohms
L1 10 nH
Biasing and Operation
The VMMK-3603 is biased with a positive supply connected
to the output pin Vd through an external user supplied
bias decoupling network. Nominal current draw is 22 mA.
A typical biasing scheme is shown in Figure 12.
Figure 13. Example demonstration circuit of VMMK-3603 for broadband
operation (1 GHz to 6 GHz).
A layout of a typical demo board is shown in Figure 14. The
output bias decoupling network can be easily constructed
using small surface mount components. The value of the
output inductor can have a major effect on both low and
high frequency operation. The demo board uses a 10 nH
inductor that has a self resonant frequency higher than
the maximum desired frequency of operation.
If the self-resonant frequency of the inductor is too close
to the operating band, the value of the inductor will need
to be adjusted so that the self-resonant frequency is sig-
nificantly higher than the highest frequency of operation.
A 10 ohm resistor is placed in series with the inductor
to help provide greater bandwidth and to help with low
frequency stability. To help with low frequency stability an
820 ohm resistor is used to shunt the input line to ground.
8.2 pF capacitors are used as dc blocks on the RF input and
RF output lines.
Typically a passive component company like Murata does
not specify S parameters at frequencies higher than 5 or
6 GHz for larger values of inductance making it difficult
to properly simulate amplifier performance at higher fre-
quencies. It has been observed that the Murata LQW15AN
series of 0402 inductors actually works quite well above
their normally specified frequency.
The parallel combination of the 100 pF and 0.1 μF capaci-
tors provide a low impedance in the band of operation
and at lower frequencies and should be placed as close
as possible to the inductor. The low frequency bypass
provides good rejection of power supply noise and also
provides a low impedance termination for third order low
frequency mixing products that will be generated when
multiple in-band signals are injected into any amplifier.
Amp
Input
Vdd
Output
Output
Pad
Ground
Pad
Input
Pad
50 Ohm line 50 Ohm line
100 pF
0.1 MF
10 nH
8.2 pF
820
8.2 pF
10
9
S Parameter Measurements
The S-parameters are measured on a 0.016 inch thick
RO4003 printed circuit test board, using G-S-G (ground
signal ground) probes. Coplanar aveguide is used to
provide a smooth transition form the probes to the device
under test. The presence of the ground plane on top of
the test board results in excellent grounding at the device
under test. A combination of SOLT (Short – Open – Load
– Thru) and TRL (Thru – Reflect – Line) calibration tech-
niques are used to correct for the effects of the test board,
resulting in accurate device S parameters.
Package and Assembly Note
For detailed description of the device package, handling
and assembly, please refer to Application Note 5378.
Ordering Information
Part Number
Devices Per
Container Container
VMMK-3603-BLKG 100 Antistatic Bag
VMMK-3603-TR1G 5000 7” Reel
Package Dimension Outline
CARRIER TAPE
USER FEED
DIRECTION
REEL
Device Orientation Device Orientation
Dimensions
Symbol Min (mm) Max (mm)
E 0.500 0.585
D 1.004 1.085
A 0.225 0.275
Note:
All dimensions are in mm
A
E
D
TOP VIEW END VIEW
•MY
•MY
•MY
•MY
8 mm
4 mm
USER FEED DIRECTION
Notes:
“M” = Device Code
“Y” = Month Code
ESD Precautions
Note: These devices are ESD sensitive. The following pre-
cautions are strongly recommended. Ensure that an ESD
approved carrier is used when die are transported from
one destination to another. Personal grounding is to be
worn at all times when handling these devices. For more
detail, refer to Avago Application Note A004R: Electro-
static Discharge Damage and Control.
For product information and a complete list of distributors, please go to our web site: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2011 Avago Technologies. All rights reserved.
AV02-2919EN - April 13, 2011
Notice:
1. 10 Sprocket hole pitch cumulative tolerance is ±0.1 mm.
2. Pocket position relative to sprocket hole measured as true position
of pocket not pocket hole.
3. Ao & Bo measured on a place 0.3 mm above the bottom of the
pocket to top surface of the carrier.
4. Ko measured from a plane on the inside bottom of the pocket to
the top surface of the carrier.
5. Carrier camber shall be not than 1 m per 100 mm through a length
of 250 mm.
Unit: mm
Symbol Spec.
K1 –
Po 4.0±0.10
P1 4.0±0.10
P2 2.0±0.05
Do 1.55±0.05
D1 0.5±0.05
E 1.75±0.10
F 3.50±0.05
10Po 40.0±0.10
W 8.0±0.20
T 0.20±0.02
Note: 2
P2
Note: 1
Po
Do B
B
Note: 2
E
F
W
AA
P1 D1
R0.1
Ao
5° (Max)
Scale 5:1
AA SECTION
Ao = 0.73±0.05 mm
Bo = 1.26±0.05 mm
Ko = 0.35 +0.05 mm
+0
Scale 5:1
BB SECTION
5° (Max)
Bo
Ko
T
Tape Dimensions
