THAN0210_Rev.1.00_E THC63LVD827(-Q) Evaluation Kit LVDS Dual Link Evaluation Board Parts Number: THEVA827 1. General Description THEVA827 is designed to evaluate THC63LVD827(-Q) for transmission video data. THC63LVD827(-Q) chipset can transmit 24bit RGB data and HS/VS/DE sync via dual channel LVDS. The maximum clock frequency of THC63LVD827(-Q) is 174MHz. 2. Features THC63LVD827 Low power 1.8V CMOS design (1.8~3.3V IO voltage supported) Power down mode Wide dot clock range suited for TV signal(480i to 1080p), PC signal(VGA to WUXGA) PLL requires no external components Clock edge selectable Single TTL in, Single/Dual LVDS (Open-LDI) out Double Edge Input(Single in/Dual out Mode) Additional 6bit only low power mode 2 LVDS Data Mapping Modes Pseudo Random Pattern Generation Circuit Support Reduced Swing LVDS for Lower EMI TFBGA 72 Pin 7x7mm 0.65mm pitch 3. Overview Figure 1 THEVA827 THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 1/7 Security E THAN0210_Rev.1.00_E 4. Power Supply Setup This chapter shows power supply condition. Caution: Please check if there is no power-GND short on below red trace before supplying any power. 1.8~3.3V Power Supply to the Board Evaluation board requires 1.8~3.3V power supply. Please use "CON201" connector typically. Ground 1.8~3.3V power supply Figure 2 THEVA827 power supply for evaluation board Power Supply from / to Connector power supply can be connected to Header201 and CON202 by using W201 and W202 solder jumper. THEVA827 W201: Connect the power supply with pin#1, 2 and 3 of Header201. W202: Connect the power supply with pin#29 and 30 of CON202. Figure 3 THEVA827 power supply from / to each Connector THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 2/7 Security E THAN0210_Rev.1.00_E 5. Function Setting Setting pin of the board is shown in yellow area of Figure 4. Setting pins Figure 4 THEVA827 position of function setting pins Pin#2 of each 3HEADER is connected to IC's setting pin. Each setting pin's high or low setting can set by connecting pin#2 of 3HEADER and high level or low level. (a)3HEADER Description (b)High Level Setting (c)Low Level Setting Figure 5 Schematic diagram of High / Low setting description 6. Clock Input from SMA Connector THEVA827 can also choose the TTL clock input from SMA connector by using 0ohm resistor. If you want to use SMA connector for clock input, please change the 0ohm resistor mount from R210 to R211. Figure 6 THEVA827 TTL clock input connector select THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 3/7 Security E THAN0210_Rev.1.00_E 7. Status Indicate LED LED "D201" indicates power supply status. 8. Function This chapter shows function setting of THEVA827. Table 1 THEVA827 Function Setting Description Silk Symbol R/F R/F RS Function Input clock triggering edge select. H : Rising Edge L : Falling Edge LVDS swing mode, VREF select. RS RS LVDS Swing Small Swing Input Support VIHM 350mV N/A VIMM 350mV RS = VREF VILM 200mV N/A LVDS mapping table select MAP MAP Mapping Mode H Mapping MODE1 L Mapping MODE2 MAP Pixel data mode select MODE MODE O/E OE /PDWN PDWN PRBS PRBS 6B/8B 6B/8B DDRN DDRN MODE Function H L Single Link (Single-in / Single-out) Dual Link (Single-in / Dual -out) Output enable H : Output Enable L : Output Disable (all outputs are Hi-Z) Power down function setting H : Normal Operation L : Power Down Mode (All outputs are Hi-Z) PRBS (Pseudo Random Binary Sequence) generator is active for evaluation purposer H : PRBS Generator Enable L : Normal Operation 6bit / 8bit mode select H : 6bit mode (21bit mode) L : 8bit mode (27bit mode) DDR enable when MODE=L (Dual out mode), Negative active polarity H : DDR (Double Edge input) function disable L : DDR (Double Edge input) function enable THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 4/7 Security E D C B GND 2 C206 10uF 16 19 B3 B4 31 34 37 40 B7 B8 B9 HSYNC 1 GND 28 B6 2 3 5 6 8 9 11 12 14 15 17 18 20 21 23 24 26 27 29 30 32 33 35 36 38 39 41 42 44 45 47 48 GND RS CLKIN1_CON G2 G3 G4 G5 G6 G7 G8 G9 VSYNC DE R2 R3 R4 R5 R6 R7 R8 R9 2 2 GND PDWN 2 Header202 IOVCC 3HEAD(NC) GND VDD OE Header203 3HEAD(NC) CLKIN1_SMA R211 0(NC) CLKIN1_CON R210 0 GND C205 10uF SMA103-T16(NC) SMA201 1 SML-310MT D201 W201 Solder Jumper VDD PCN10-48P-2.54DS_2(NC) 46 43 25 B5 22 13 B2 10 7 4 1 Header201 GND VDD 1 GND R209 150 2 A 1 3 VDD2 1 3 2 3 C208 10uF MODE 2 Header204 3HEAD(NC) CLKIN GND IC201 uPC2918BT OUTPUT 3 4 GND GND 2 C207 10uF INPUT 1 1 3 TP201 1 3 VDD G9 H9 J9 F9 F8 C3 D8 D9 G8 C1 E7 E8 E9 F7 C2 DE VSYNC HSYNC CLKIN RS Reserved1 PDWN OE R/F PRBS MODE MAP DDRN 6B/8B DDRN 2 Header205 3HEAD(NC) G1 G2 F1 F2 E1 E2 D1 D2 J4 H4 J3 H3 J2 H2 J1 H1 J8 H8 J7 H7 J6 H6 J5 H5 VDD1.8 R9 R8 R7 R6 R5 R4 R3 R2 G9 G8 G7 G6 G5 G4 G3 G2 B9 B8 B7 B6 B5 B4 B3 B2 GND 4 PRBS Header206 3HEAD(NC) RS Reserved1 /PDWN O/E R/F PRBS MODE MAP DDRN 6B/8B N/C CLKIN DE VSYNC HSYNC R17 R16 R15 R14 R13 R12 R11 R10 G17 G16 G15 G14 G13 G12 G11 G10 B17 B16 B15 B14 B13 B12 B11 B10 IC202 1 3 282836-2(NC) CON201 2 0 L201 6B/8B Header207 2 GND GND GND GND GND GND GND PLLVCC LVDSVCC LVDSVCC VCC VCC IOVCC TA2TA2+ TB2TB2+ TC2TC2+ TCLK2TCLK2+ TD2TD2+ TA1TA1+ TB1TB1+ TC1TC1+ TCLK1TCLK1+ TD1TD1+ VDD 5 MAP Header208 2 PLLVCC 3HEAD(NC) C4 C6 D7 E3 F3 G4 G6 C7 D3 R/F Header209 3HEAD(NC) GND C219 0.01uF C220 0.1uF 0.01uF 0.1uF 0.01uF 0.1uF C211 0.01uF C212 0.1uF C213 0.01uF C214 0.1uF C209 0.01uF C210 0.1uF LVDSVCC C215 C216 LVDSVCC C217 C218 VCC VCC IOVCC G7 G3 C5 TA2TA2+ TB2TB2+ TC2TC2+ TCLK2TCLK2+ TD2TD2+ B6 A6 B7 A7 B8 A8 B9 A9 C8 C9 G5 TA1TA1+ TB1TB1+ TC1TC1+ TCLK1TCLK1+ TD1TD1+ B1 A1 B2 A2 B3 A3 B4 A4 B5 A5 GND L202 2 6 VDD1.8 VDD 6 Header210 3HEAD(NC) GND C202 10uF LVDSVCC 0(NC) MPZ1608R471A R202 VDD1.8 R206 C201 10uF 0 VCC 5 MPZ1608R471A THC63LVD827 R205 0(NC) R201 3HEAD(NC) VDD1.8 VDD 1 3 4 1 3 1 3 2 1 5/7 3 Copyright(C) 2016 THine Electronics, Inc. 3 1 L203 0 R207 R213 0 R212 0(NC) Date: File: A3 Size VDD VDD2 0(NC) R208 0 R204 VDD GND TA2TA2+ TB2TB2+ TC2TC2+ TCLK2TCLK2+ TD2TD2+ TA1TA1+ TB1TB1+ TC1TC1+ TCLK1TCLK1+ TD1TD1+ W202 Solder Jumper 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 7 8 8 Revision 1.00 52271-3069(NC) CON202 GND C204 10uF IOVCC MPZ1608R471A L204 2016/03/07 Sheet 1 of 1 C:\Users\..\THEVA827-Q_R100.SchDoc Drawn By: Number THEVA827(-Q) GND Title Reserved1 IOVCC GND C203 10uF PLLVCC 0(NC) MPZ1608R471A R203 7 D C B A THAN0210_Rev.1.00_E 9. Schematic Figure 7 THEVA827 Schematic THine Electronics, Inc. Security E THAN0210_Rev.1.00_E 10. Bill of Materials Table 2 THEVA827 BOM Comment Description Value Note Capacitor2012 2012 10uF 16V Capacitor1005 Capacitor1005 282836-2 CN-FFC(1.0)30PD LED1608 1005 1005 282836-2 CN-FFC(1.0)30PD 1608 0.01uF 0.1uF 282836-2(NC) 52271-3069(NC) SML-310MT 16V 16V 5mm pitch 1mm pitch Green 3HEAD 3HEAD 3HEAD(NC) 2.54mm pitch uPC2918BT THC63LVD827 Inductor1608 Resistor1608 Resistor1608 SC-63 TFBGA72 1608 1608 1608 MPZ1608R471A 0ohm 150 1A(0ohm) 0.1W Designator C201, C202, C203, C204, C205, C206, C207, C208 C209, C211, C213, C215, C217, C219 C210, C212, C214, C216, C218, C220 CON201 CON202 D201 Header202, Header203, Header204, Header205, Header206, Header207, Header208, Header209, Header210 IC201 IC202 L201, L202, L203, L204 R205, R206, R207, R204, R210, R213 R209 Q'ty 8 6 6 1 1 1 9 1 1 4 6 1 11. Set Items Table 3 Set Items TYPE Part No. DC Connector 282836-2 FFC Connector for LVDS Link 52271-3069 FFC 30pin 1mm Pitch for LVDS Link 98267-0475 Pin Header --It's possible to mount these parts on this board and use. THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 6/7 Security E THAN0210_Rev.1.00_E 12. Notices and Requests Please kindly read, understand and accept this "Noticees and Requests" before using this product. For the Material: 1. The product specifications described in this material are subject to change without prior notice. 2. The circuit diagrams described in this material are examples of the application which may not always apply to design of respective customers. THine Electronics, Inc. ("THine") is not responsible for possible errors and omissions in this material. Please note if the errors or omissions should be found in this material, THine may not be able to correct them immediately. 3. This material contains THine's copyright, know-how or other proprietary. Copying or disclosing of the contents of this material to any third party without THine's prior permission is strictly prohibited. For the Product: 1. This product is solely designed for evaluation purpose, and other purposes including mass production and distribution are not intended. 2. This product has been solely manufactured for electric design engineers but not for end-users. 3. This product is not radiation-tolerant product. 4. This product is presumed to be used for general electric device, not for applications which require extremely high-reliability/safety (including medical device concerned with critical care, aerospace device, or nuclear power control device). Also, when using this product for any device concerned with control and/or safety of transportation mean, traffic signal device, or other various types of safety device, such use must be after applying appropriate measures to the product. 5. This product has been designed with the utmost care to accomplish the purpose of evaluation of IC products manufactured by THine Electronics, Inc., however, THine MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO ANY PERFORMANCE OR FUNCTION OF THIS PRODUCT IN ANY CIRCUMSTANCE. 6. This product has been manufactured with the utmost care in quality control and product reliability, however, there may be faults or defects with a low but fixed probability, as inevitable phenomenon concerned with semiconductor manufacturing processes. Therefore, Customers are encouraged to have sufficiently redundant or error-preventive design applied to the use of the product so as not to have THine's product cause any social or public damage. Replacement of the product is only available in case of obvious defects of mount devices at the point of unpacking the product. Neither replacement nor failure analysis of the product is available in any other case of defects with the product and/or the product's components. 7. Customers are asked, if required, to judge by themselves on whether this product falls under the category of strategic goods under the Foreign Exchange and Foreign Trade Control Law. 8. Please Note that if infringement of any third party's industrial ownership should occur by using this product, THine will be exempted from any responsibility unless it directly relates to the production process or functions of the product. 9. Developing, designing and manufacturing of Customers' own products, equipments or system by using of this product is strictly prohibited in any way. THine Electronics, Inc. sales@thine.co.jp THine Electronics, Inc. Copyright(C) 2016 THine Electronics, Inc. 7/7 Security E