Ordering information Small, common mode EMI/EMC Filters in 150kHz to 1MHz (1-Stage filter) EAC series EAC -10 -472 1 2 3 -O 4 1 Model Name 2 Rated Current 3 Line to ground capacitor code:See table 1.1. R table1.1 Line to ground capacitor code Code 681 102 222 332 472 Line to ground Leakage Current capacitor (Input 125/250V 60Hz) (nominal value) 75.5 A/150 A max 680pF 0.13mA/0.25mA max 1000pF 0.25mA/0.5 mA max 2200pF 3300pF 0.38mA/0.75mA max 0.5 mA/1.0 mA max 4700pF When the line to ground capacitor code is different, the attenuation characteristic is different. * 4 Options D :DIN rail installation type * The dimensions change when the option is set. Refer to External view. The terminal cover is retracted inside the unit DIN rail installation type is option Features of EAC series Small, common mode EMI/EMC Filters in 150kHz to 1MHz(1-Stage filter) - Single Phase 250 VAC -Small-size -Quick and easy push-down terminal Just connect the wires,push-down and tighten the screws with a screwdriver Specifications No. 1 Items EAC-03-472 Rated Voltage[V] AC 1f 250 / DC250 EAC-06-472 EAC-10-472 EAC-16-472 EAC-20-472 EAC-30-472 10 16 20 30 2 Rated Current[A] 3 3 Test Voltage (Terminal-Mounting Plate) 2,500 VAC (Cutoff Current = 20mA), 1minute at room temperature and humidity 6 4 Isolation Resistance (Terminal-Mounting Plate) 500 VDC 500MW min at room temperature and humidity 5 Leakage current 125/250V 60Hz 0.5mA/1.0mA max 6 DC resistance 180mW max 7 Safety agency approval temperatures -25 to +85C (Refer to Derating Curve) 8 Operating temperature -40 to +85C (Refer to Derating Curve) 9 Operating humidity 20 to 95%RH (Non condensing) 10 Storage temperature/humidity -40 to +85C/20 to 95%RH (Non condensing) 11 Vibration 10 to 55Hz, 19.6m/s2 (2G), 3min. Period, 1hour each X, Y and Z axis 12 Impact 196.1m/s2 (20G), 11ms Once each X, Y and Z axis 13 Safety agency approvals UL1283, CSA C22.2 No.8 (C-UL), DIN EN60939 VDE0565 Teil3-1, ENEC (At only AC input) 14 Case size (without projection) /Weight 39X30X85 mm [1.54X1.18X3.35 inches] (WXHXD) /170g max (Option : -D refer to external view) Circuit Diagram 110mW max 40mW max 20mW max 10mW max 6mW max Derating Curve Case 1 LINE 2 CY CY 3 LOAD 4 Load Factor [%] 100 80 60 40 20 0 -40 CY : Line to ground capacitor EA/ES-1 : Mounting Plate -30 -20 40 50 55 60 Ambient Temperature [C] 70 80 90 EAC,EAM,EAP series External view This product is shipped in the following condition,because it is equipped with push-down terminals. 1The terminal cover is retracted inside the unit. 2The screws for connecting the terminals are held in the up right position. Standard Type 85 [3.35] 75 0.5 [2.95] 72 39 [1.54] 12.7 9.7 0.5 [0.38] 2-f4.8 [0.19] Mounting Hole 11.5 [0.45] [1.24] 2-M4 Output Terminal Name Plate Input Terminal Terminal cover Mounting Plate 21 [0.83] Terminal cover M4 Protection Earth Tolerance : 1 [0.04] Weight : 170g max Mounting Plate : Iron (surface finishing:nickel plating)=1.0 [0.04] CasePBT Dimensions in mm, [ ]=inches Terminal block screw tightening torque M41.6Nm(16.9kgfcm)max 30 [1.18] 2 Closed the terminal cover [0.08] 2-M4 Protection Earth [0.1] 31.5 Terminal cover 2.5 M4 [0.5] [2.83] DIN rail installation Type [0.33] 72 12.7 9.7 M4 21 [0.83] 11.5 39 2-M4 Output Terminal Name Plate Terminal cover [0.1] [0.45] [0.38] 2-M4 Input Terminal 2.5 Mounting Plate [1.54] Terminal cover M4 Protection Earth [0.5] [2.83] +2 -1 8.5 85 [3.35] Terminal cover Protection Earth [0.28] Tolerance : 1 [0.04] Weight : 170g max Mounting Plate : Iron (surface finishing:nickel plating)=1.0 [0.04] CasePBT Dimensions in mm, [ ]=inches Terminal block screw tightening torque M41.6Nm(16.9kgfcm)max 7 [0.35] (9) 30 [1.18] 2 [0.08] Closed the terminal cover DIN rail Note when installing the EMI/EMC Filter on a DIN rail. When the EMI/EMC Filter is grounded through the DIN rail, the proper noise attenuation may not be achieved. Be sure to connect the protection earth (PE) of the EMI/EMC Filter body to the earth. It can connect the ground to either one only. DIN rail Name Plate EA/ES-4