Model HRS100 Vishay Spectrol Hall Effect Rotary Position Sensor FEATURES * Tight Linearity of 2% or Less * Programmable Temperature Coefficient * Precision Ultra Long Life Device * Rugged 10 Million Cycle Life * Cost Effective in Harsh Environment * Customised Offset and Gain Control Available ELECTRICAL SPECIFICATIONS PARAMETER UNIT Electrical Angle 45, 60, 80, 90 2 degrees 180, optional* Degrees Electrical Output Range % 0 - 100, 5 - 45, 5 - 95, 10 - 90 of applied Vdd Customer specific linear outputs available* Linearity % 2 (less than 1 typical) Output Current mA 2 max. (source or sink) Over Voltage Protection VDC 18 max Reverse Voltage Protection VDC - 14.5 max Supply Voltage VDC 5 10% Supply Current mA 5 typical Load Life Hrs Greater than 10,000 at rated load ESD Sensitivity - EMI 7KV max (Human body model) Standard electronic assembly practices should be observed V/M 30, 10Khz to 1000Mhz at 3 meters ENVIRONMENTAL SPECIFICATIONS Low Temperature Operation - 40C High Temperature Operation + 85C Storage Temperature + 105C max Shock 50Gs, 11 ms Vibration 15Gs. 10 to 2000Hz *Consult the factory ORDERING INFORMATION HRS100 MODEL N MOISTURE SEAL N BUSHING LENGTH Y: Yes N: No N: 0.375" G: 0.250" www.vishay.com 40 32 SHAFT LENGTH P SHAFT END S TERMINALS 1/64" P: Plain round Increments S: Slotted measured from F: Flatted mounting surface, 1.5 inches max D A ROTATION LINEARITY S: Solder lug A: 45 A: 2% (90 from shaft) B: 60 B: 1.5% F: S bent 90 to C: 80 C: 1% front D: 90 B: S bent 90 to E: 180 back W: Cable wire length (Specify length, inches) C: Cable wire W/connector: (Specify cable length and connector) 0.245 0.270 1.950 2.205 VMIN VMAX VMIN VMAX CCW END CCW END CW END CW END Specify out put voltages at both ends, Minimum and maximum values Document Number: 57092 Revision 31-May-01 Model HRS100 Hall Effect Rotary Position Sensor Vishay Spectrol DIMENSIONS in inches (millimeters) MOUNTING SHAFT 0.063 + 0.015 - 0.005 0.080 1.094 SLOTTED SHAFT OUTPUT 0.520 0.375 0.047 0.005 FLATTED SHAFT 0.218 0.002 0.875 0.375 0.010 0.112 0.128 1 2 3 GND Vdd OUTPUT APPLICATIONS NOTE; FLAT WILL EXTEND TO WITHIN 0.062 OF BUSHING WHERE SHAFT LENGTH WILL NOT PERMIT STANDARD FLAT FORKLIFT - INDUSTRIAL TRUCK - FARM EQUIPMENT: Throttle/speed control (Forward, Neutral, Reverse) Foot pedal position sensor Lift and shuttle position and control Tilt control and feedback of tilt position Implement grimbal position and control Steering position AIRCRAFT Rudder, pitch - trim or aileron position Servo tab position Flap and slat position Flap asymmetry sensors/detection Elevator position Nose wheel position Throttle position Foot pedal position sensor Fly by wire feedback systems MARINE Throttle position sensor Outboard motor Inboard/outboard (O) based power systems Diesel engine, electronic injector control Control position sensor: Rudder position Trim tab and plain position Drive tilt and drive gimbal position Auto pilot feed back and controls Drive by wire systems, control and feedback AUTOMOTIVE Foot pedal position sensor Throttle position sensor Steering position sensor Suspension system position sensors Seat position sensor Mirror position sensor MECHANICAL SPECIFICATIONS PARAMETER UNIT Housing - Bushing - Shaft - AR Lugs Terminal Style Mechanical Angle Rotational Life Rotational Torque 0.598, 0.015 Depth F.M.S x 1.094, 0.015 diameter. Stainless steel can 3/8 - 32, 0.375 max Length F.M.S Excludes C - RING* 0.249 0.001 diameter, Flatted, Slotted, Lengths to 1.5 inches* 2 at 180, on 0.531 radius, 0.125W x 0.128 F.M.S 1 lug optional* - Solder lugs or wire leads deg 45, 60, 80, 90, 2 180, optional* M 10 (min) in - oz 2.0 max. at 25C with shaft seal Stop Torque - 5 inch pounds Push Out - 20 pounds min Pull Out - 10 pounds min Document Number: 57092 Revision 31-May-01 www.vishay.com 41