Computer-On-Modules
http://www.adlinktech.com/Computer-on-Module
Useful time saving tools to expedite
your application development
Engineering Test Tools
BattMan
Smart Battery Management
Reference Platform
Flat Panel Transfer Board
ADD2 DVI-D Adapter Card
The BattMan Smart Battery Management Reference Platform allows
developers to rst verify on a system level and then easily implement
the same type of battery power design into their own carrier board.
BattMan supports single battery mode or balanced loading and
unloading using two batteries.
Contents
• Smart Battery management module
• Two Li-ion smart batteries at 14.V, 5200 mAh each
• 19V notebook type adapter (110/220Vac)
• USB key with schematics, BOM and manual
The Flat Panel Transfer Board (FPTB) supports prototyping and
verication of LVDS and TTL at panel displays . The module includes
an LVDS-to-TTL converter to allow users to implement TTL displays
with COM modules that support LVDS only. Onboard PWM circuitry
supports backlight control for LVDS and TTL displays.
The ADD2 DVI-D Adapter Card provides DVI-D display output (digital
only) for modules that support SDVO output. This adapter plugs
into the PEG x16 connector on Express-BASE, SDVO connector on
nanoX-BASE, and DDI connector on Express-BASE6.
Ordering Information
Model Number Description/Configuration
StarterKit-Battman Smart Battery Management Reference Platform for COM
Express® modules (includes two Smart Batteries, 19V
adapter and USB key)
Ordering Information
Model Number Description/Configuration
FPTB Flat Panel Transfer Board for LVDS-to-TTL signal
conversion
LVDS cable for FPTB Reference carrier LVDS output to FPTB LVDS input
cable (supports Express-BASE, Express-BASE6 and
nanoX-BASE)
Note: Included in the Starter Kit - nanoX.
Ordering Information
Model Number Description/Configuration
FI-7307(N16D)-F ADD2 DVI-D Adapter
PCIe x16-to-two-x8 Adapter Card
LPC POST Debug Board
COM-T6T2 Adapter Board
T6-DDI Video Adapter Card
COM Express Type 6 to Type 2 Conversion
COM Express Type 6 DDI to HDMI/DVI/DisplayPort
The ADLINK PCIe x16-to-two-x8 adapter card can be used with
modules that support bifurbication on the PEG x16 interface. The
card reroutes the PCIe x16 to two x8 and allows testing of two
independent PCIe add-on cards with x8/x4/x2/x1 width.
All ADLINK COM modules include an LPC debug connector. The
LPC POST Debug Board connects to this connector and can provide
monitoring of BIOS POST status. The LPC POST Debug Board
connects directly to the module and can be used regardless of the
carrier board being used.
The COM-T6T2 Adapter Board allows COM Express Type 6 modules
to be tested on existing COM Express Type 2 carriers. The adapter
board adds PATA IDE (via a SATA to PATA bridge) and PCI bus (via a
PCIe-to-PCI bridge) to the signals on the CD connector. The SDVO
port is rerouted to correspond to the Type 2 pin denition. PCIe x16
is not supported.
The T6-DDI Video Adapter Card provides connector access to COM
Express Type 6 module Digital Display Interface (DDI) outputs. The
card must be installed on the Express-BASE6 Type 6 carrier board
using the second PCIe x16 slot with proprietary pinout. Jumper
settings on the card congure output to either HDMI or DisplayPort.
DVI can be tested by using a passive dongle connected to a
DisplayPort output.
Ordering Information
Model Number Description/Configuration
P16TO28 PCIe x16-to-two-x8 adapter card
Ordering Information
Model Number Description/Configuration
LPC_DEBUG_2 LPC POST debug board with secondary LPC BIOS
Ordering Information
Model Number Description/Configuration
COM-T6T2 COM Express Type 6 to Type 2 adapter card (w/ SDVO)
Ordering Information
Model Number Description/Configuration
T6-DDI COM Express Type 6 DDI-to-HDMI/DVI/DisplayPort
adapter card (includes DVI dongle)
