SMT15E-12W3V3J - EMERSON�NETWORK POWER

SMT15E SERIES

3.0 Vin to 5.5 Vin Single output

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

[2YEAR WARRANTY ]

15 A current rating

Input voltage range: 3.0 Vdc to 5.5 Vdc

Output voltage range: 0.8 Vdc to 3.63 Vdc

Ultra high efficiency: 96% @ 5 Vin and 3.3 Vout

Extremely low internal power dissipation

Minimal thermal design concerns

Designed in reliability: MTBF of >7 million hours per Telcordia SR-332

Ideal solution where board space is at a premium or tighter card pitch is required

Industry standard surface-mount footprint

Available RoHS compliant

THE SMT15E series are non-isolated dc-

dc converters packaged in a surface

mount footprint giving designers a cost

effective solution for conversion from

either a 5 Vdc or 3.3 Vdc input to output

voltages of 0.8 Vdc to 3.63 Vdc. Local

voltage conversion by the SMT15E series

from existing 5 Vdc or 3.3 Vdc system

voltages eliminates the need for redesign

of existing power architectures when

voltage requirements change. The

SMT15E is designed for applications that

include distributed power, workstations,

optical network and wireless applications.

Implemented using state of the art surface

mount technology and automated

manufacturing techniques, the SMT15E

offers compact size and efficiencies of up

to 96%.

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - turn on Vin (on) 2.25 2.70 3 V DC Will regulate @ Vin >3V if Vout ≤

2V5

Turn on delay - enabled, Tdelay 20 msec With the enable signal asserted,

then power applied (power) this is the time from when the

input voltage reaches the

minimum specified operating

voltage until the output voltage

is within the total regulation

band

Turn on delay - power Tdelay 20 msec Vin = Vin (nom), then enabled.

applied, then enabled (enable) This is the time taken until the

output voltage is within the total

error band

Rise time Trise 15 msec From 10% to 90%; full resistive

load, no external capacitance

Stresses in excess of the maximum ratings can cause permanent damage to the device. Operation of the device is not implied at these or any

other conditions in excess of those given in the specification. Exposure to absolute maximum ratings can adversely affect device reliability.

All specifications are typical at nominal input Vin = 5V, full load under any resistive load combination at 25˚Cunless otherwise stated.

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - continuous Vin (cont) -0.3 5.5 V DC Vin(+) - Vin(-)

Input voltage - peak/surge Vsurge -0.3 6 V DC 2s max, non-repetitive

Operating temperature Top -40 100 ºC Measured at thermal reference

points, see Note 1 for thermal

Derating

Storage temperature Tstorage -40 125 ºC

Output power (S2V5) Pout (max) 0 41.25 W

Output power (S3V3) Pout (max) 0 54.45 W

Output power (W3V3) Pout (max) 0 54.45 W

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input voltage - operating Vin (oper) 3 5 5.5 V DC See Note 2

Input current - no load lin 70 150 mA DC Vin (min) - Vin (max), enabled

Input current - quiescent lin (off) 2 mA DC Converter disabled

Inrush current (i2t) linrush 12 A2µs

Complies with ETS300 132 Part 4.7,

with recommended LISN

Input ripple current 110 mA rms

Input fuse* 16 A Slowblow/antisurge HRC

recommended

Absolute Maximum Ratings

Input Characteristics

Turn On/Off

*Fuse A - S(T) 1.25 x 0.25 inches

SIBA P/N 70-065-65/16ARS

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

3www.artesyn.com

Characteristic - Signal Name Symbol Min Typ Max Units Notes and Conditions

At remote/control ON/OFF pin See Notes 2 and 3

Open collector or equivalent See Application Note 136 for

compatible Remote ON/OFF details

Control pin open circuit voltage Vih 0VI

ih = 0 µA; open circuit voltage

High level input current Iih 300 µA Current flowing into control pin

when pin is pulled high

High level input voltage Vih 1.2 Vin Converter guaranteed OFF when

control pin is greater than Vih

(min)

Acceptable high level Iih (leakage) -10 µA Acceptable leakage current from

leakage current signal pin into the open collector

driver (neg = from converter)

Low level input voltage ViI 0 0.5 V Converter guaranteed ON

when control pin is

less than Vil (max)

Low level input current IiI 20 µA Vil =<0.4 V

Characteristic Symbol Min Typ Max Units Notes and Conditions

Mean time between failure MTBF 680,000 Hours MIL-HDBK-217F,

Vin = Vin (nom); Iout = Iout

(max);ambient 25ºC;

ground benign environment

Mean time between failure MTBF 7,042,000 Hours Telcordia SR-332

Mean time between failure MTBF TBA Hours Demonstrated. This entry will be

periodically updated as the

number of test hours increase

Signal Electrical Interface

Reliability and Service Life

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Other Specifications

Characteristic Symbol Min Typ Max Units Notes and Conditions

Switching frequency Fsw 300 kHz Fixed frequency

Weight 6.3 g

Coplanarity 100 µm Measured from seating plane

EMC

Electromagnetic Compatibility

Phenomenon Port Standard Test level Criteria Notes and conditions

Immunity:

Conducted immunity EN61000-4-6

Radiated immunity EN61000-4-3

ESD Enclosure EN61000-4-2 6kV contact NP As per ETS 300 386-1 table 5

8kV air

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

Performance criteria:

NP: Normal Performance: EUT shall withstand applied test and operate within relevant limits as specified without damage.

RP: Reduced Performance: EUT shall withstand applied test. Reduced performance is permitted within specified limits, resumption to

normal performance shall occur at the cessation of the test.

LFS: Loss of Function (self recovery): EUT shall withstand applied test without damage, temporary loss of function permitted during test.

Unit will self recover to normal performance after test.

Referenced ETSI standards:

ETS 300 386-1 table 5 (1997): Public telecommunication network equipment, EMC requirements

ETS 300 132-2 (1996): Power supply interface at the input to telecommunication equipment: Part 2 operated by direct current (DC)

ETR 283 (1997): Transient voltages at interface A on telecommunication direct current (DC) power distributions

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

5www.artesyn.com

Material Ratings

Characteristic - Signal Name Notes and Conditions

Flammability rating UL94V-0

Model Input Output Output Current Typical Max. Load

Number Voltage Voltage (Max.) Efficiency Regulation

SMT15E-05S2V5J 3.0 - 5.5VDC 2.5V 15A 93.5% ±1.0%

SMT15E-05S3V3J 4.5 - 5.5VDC 3.3V 15A 95% ±1.0%

SMT15E-05W3V3J 3.0 - 5.5VDC 0.8V - 3.63V 15A 95% ±1.0%

Model Numbers

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

RoHS Compliance Ordering Information

The ‘J’ at the end of the part number

indicates that the partis Pb-free

(RoHS 6/6 compliant). TSE RoHS 5/6

(non Pb-free) compliant versions may

be available on special request, please

contact your local sales representative

for details.

Safety Agency Approvals

Characteristic Notes and Conditions

UL/cUL60950 File No. E174104

TÜV Product Services EN60950 B03 10 38572 037

CBcertficate and report to

IEC60950 DE3-51686M1

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Input Characteristics

S2V5 Model

Electrical Characteristics - O/P

S2V5 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo(nom) 2.43 2.5 2.57 V DC Vin = Vin (nom); Iout = Iout (nom)

Total regulation band Vo2.38 2.612 V DC For all line, static load and

temperatureuntil end of life

Line regulation 0.2 0.5 % Iout = Iout (nom);

Vin (min) to Vin (max)

Load regulation 1.0 % Vin = Vin (nom);

Iout (min) to Iout (max)

Output current continuous Iout 0 15 ADC

Output current - short circuit Isc 10 20 Arms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 60 mV pk-pk Measurement bandwidth:

Vrms 25 mV rms 20MHz. See Application Note

136 for measurement set-up

details

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 8 9 A DC Vin = Vin (nom); Iout = Iout

(max.); Vo= Vo(nom)

Reflected ripple current Iin (ripple) 110 mA rms Iout = Iout (max.), measured

370 mA pk-pk without external filter

Input capacitance - Cinput 18.8 µF Internal to converter

internal filter

Input capacitance - Cbypass 100 µF Recommended customer

external bypass added capacitance

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

7www.artesyn.com

EClass Non-Isolated DC-DC Converters

S2V5 Model

Electrical Characteristics - O/P

S2V5 Model

Efficiency

S2V5 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency η92.5 93.5 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency η94 95 % Iout =50% Iout (max),

Vin = Vin (nom)

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 50 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 100 mA/µsec.

Measurement taken with no

external capacitors

Load transient response - Trecovery 50 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load. Measurement

taken with no external

capacitors

External load capacitance Cext 0 10,000 µF

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Allowable output voltage* 10 % Trim up (% of Vonom).

10 % Trim down (% of Vonom)

See Application Note 136 for

details of trim equations and

trim curves

Remote sense voltage 10 % If Trim up is invoked de-rate

power accordingly (remote

sense + trim ≤ 10%)

*Vin (min) =3.3V at max. trim-up

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Input Characteristics

S3V3 Model

Electrical Characteristics - O/P

S3V3 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo(nom.) 3.21 3.3 3.39 VDC Vin = Vin (nom); Iout = Iout (nom)

Total regulation band Vo3.15 3.45 VDC For all line, static load and

temperature until end of life

Line regulation 0.2 0.5 %I

out = Iout (nom);

Vin (min) to Vin (max)

Load regulation 1 % Vin = Vin (nom);

Iout (min) to Iout (max)

Output current continuous Iout 0 15 ADC

Output current - short circuit Isc 10 20 A rms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 60 mV pk-pk Measurement bandwidth 20MHz

Vrms 25 mV rms See Application Note 136 for

set-up details

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 10.4 11.8 ADC Vin = Vin (nom);

Iout = Iout (max.); Vo= Vo(nom)

Reflected ripple current Iin (ripple) 110 mA rms Iout = Iout (max.), measured

370 mA pk-pk without external filter

Input capacitance - Cinput 18.8 µF Internal to converter

internal filter

Input capacitance - Cbypass 100 µF Recommended customer

external bypass added capacitance

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

9www.artesyn.com

EClass Non-Isolated DC-DC Converters

S3V3 Model

Efficiency

S3V3 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency η94 95 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency η94 96 % Iout =50% Iout (max),

Vin = Vin (nom)

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

Electrical Characteristics - O/P

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 60 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 100 mA/µsec.

Measurement taken with no

external capacitors

Load transient response - Trecovery 50 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load. Measurement

taken with no external

capacitors

External load capacitance Cext 0 10,000 µF

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Allowable output voltage 10 % Trim up (% of Vonom).

10 % Trim down (% of Vonom)

See Application Note 136 for

details of trim equations and

trim curves

Remote sense voltage 10 % If Trim up is invoked de-rate

power accordingly (remote

sense + trim ≤ 10%)

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Input Characteristics

W3V3 Model

Electrical Characteristics - O/P

W3V3 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Nominal set-point voltage Vo(nom.) 3.21 3.3 3.39 VDC Vin = Vin (nom); Iout = Iout (nom)

Total regulation band Vo3.15 3.45 VDC For all line, static load and

temperature until end of life

Line regulation 0.2 0.5 %I

out = Iout (nom);

Vin (min) to Vin (max)

Load regulation 1.0 % Vin = Vin (nom);

Iout (min) to Iout (max)

Output current continuous Iout 0 15 ADC

Output current - short circuit Isc 10 20 A rms Continuous, unit auto recovers

from short, Vo<100mV

Output voltage - noise Vp-p 60 mV pk-pk Measurement bandwidth 20MHz

Vrms 25 mV rms See Application Note 136 for

set-up details

Characteristic Symbol Min Typ Max Units Notes and Conditions

Input current - operating Iin 10.4 11.8 ADC Vin = Vin (nom);

Iout = Iout (max.); Vo= Vo(nom)

Reflected ripple current Iin (ripple) 110 mA rms Iout = Iout (max.), measured

370 mA pk-pk without external filter

Input capacitance - Cinput 18.8 µF Internal to converter

internal filter

Input capacitance - Cbypass 100 µF Recommended customer

external bypass added capacitance

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

11 www.artesyn.com

EClass Non-Isolated DC-DC Converters

W3V3 Model

Efficiency

W3V3 Model

Characteristic Symbol Min Typ Max Units Notes and Conditions

Efficiency η94 95 % Iout =100% Iout (max),

Vin = Vin (nom)

Efficiency η94 96 % Iout =50% Iout (max),

Vin = Vin (nom)

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

Electrical Characteristics - O/P

Characteristic Symbol Min Typ Max Units Notes and Conditions

Load transient response - Vdynamic 80 mV Peak deviation for 50% to 75%

peak deviation step load, di/dt = 100 mA/µsec.

Measurement taken with no

external capacitors

Load transient response - Trecovery 50 µsec Settling time to within 1% of

recovery output set point voltage for 50%

to 75% step load. Measurement

taken with no external

capacitors

External load capacitance Cext 0 10,000 µF

Protection and Control Features

Characteristic Symbol Min Typ Max Units Notes and Conditions

Allowable output voltage 10 % Trim up (% of Vonom).

75 % Trim down (% of Vonom)

See Application Note 136 for

details of trim equations and

trim curves

Remote sense voltage 10 % If Trim up is invoked de-rate

power accordingly (remote

sense + trim ≤ 10%)

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Figure 1: Derating Curve

with Vin = 5V and No Trim

S2V5 Model

Figure 3: Short Circuit Characteristic

(Channel 1: Is/c)

Figure 4: Typical Transient Response 50% - 75%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure 5: Typical Transient Response 75% - 50%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure 6: Typical Power-up Characteristic

(Channel 1: Vo, Channel 2: Vin)

70 75 80 85 90 95 100

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0 m/s (0 LFM)

0.5 m/s (100 LFM)

1 m/s (200 LFM)

1.5 m/s (300 LFM)

Figure 2: Efficiency vs Load

03 6 9 12 15

EFFICIENCY (%)

OUTPUT CURRENT (A)

Vin = 3V

Vin = 5V

Vin = 5.5V

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

13 www.artesyn.com

S2V5 Model

Figure 8: Typical Ripple and Noise*

(Channel 3: Vo)

Figure 7: Control On/Off Characteristic

(Channel 1: Vo, Channel 2: Remote ON/OFF)

*Multiply values by 2, see Application Note 136 for set-up details

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Figure 9: Derating Curve

with Vin = 5V and No Trim

Figure 10: Efficiency vs Load

Figure11: Short Circuit Characteristic

(Channel 4: Io)

Figure13: Typical Transient Response 75% - 50%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure12: Typical Transient Response 50% - 75%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure14: Typical Power-up Characteristic

(Channel 1: Vo, Channel 2: Vin)

S3V3 Model

70 75 80 85 90 95 100

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0 m/s (0 LFM)

0.5 m/s (100 LFM)

1 m/s (200 LFM)

1.5 m/s (300 LFM)

03 6 9 12 15

EFFICIENCY (%)

OUTPUT CURRENT (A)

Vin = 4.5V

Vin = 5V

Vin = 5.5V

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

15 www.artesyn.com

S3V3 Model

Figure 15: Control On/Off Characteristic

(Channel 1: Vo, Channel 2: Remote ON/OFF)

Figure 16: Typical Ripple and Noise*

(Channel 3: Vo)

*Multiply values by 2, see Application Note 136 for set-up details

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

Figure 17: Derating Curve

with Vin = 5V and No Trim

Figure 18: Efficiency vs Load

Figure19: Short Circuit Characteristic

(Channel 4: Io)

Figure21: Typical Transient Response 75% - 50%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure20: Typical Transient Response 50% - 75%

Step Load Change (Channel 1: Vo, Channel 4: Io)

Figure22: Typical Power-up Characteristic

(Channel 1: Vo, Channel 2: Vin)

W3V3 Model

70 75 80 85 90 95 100

OUTPUT CURRENT (A)

AMBIENT TEMPERATURE (ºC)

0 m/s (0 LFM)

0.5 m/s (100 LFM)

1 m/s (200 LFM)

1.5 m/s (300 LFM)

03691215

EFFICIENCY (%)

OUTPUT CURRENT (A)

Vin = 4.5V

Vin = 5V

Vin = 5.5V

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

17 www.artesyn.com

W3V3 Model

Figure 23: Control On/Off Characteristic

(Channel 1: Vo, Channel 2: Remote ON/OFF)

Figure 24: Typical Ripple and Noise*

(Channel 3: Vo)

*Multiply values by 2, see Application Note 136 for set-up details

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

SXA10 Series | 15W

DC/DC

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

All dimensions in inches (mm)

All tolerance ±0.010in (±0.25mm)

unless otherwise stated

SIDE VIEW

0.323 (8.21)

Installed Ht.

0.007 (0.18)

Min Clearance

Max. component

Connector (6PL)

Width :0.112 ±0.003 (2.84 ±0.08)

Length: 0.062 ±0.002 (1.57 ±0.04)

Seating Plane

1.300±0.010 (33.02 ±0.25)

0.039 (1.00)

0.530 ±0.010

(13.46 ±0.25)

TOP VIEW

BOTTOM VIEW

5432

0.430 (10.92)

0.048 (1.22)

0.075 (1.91)

0.405 (10.29)

0.297

(7.54)

0.190

(4.83)

0.190

(4.83)

0.190

(4.83)

0.310

(7.87)

Figure 25: Mechanical Drawing and Pinout Table

Pin Connections

Pin No. Function

1 Remote ON/OFF

2 Remote Sense +

3Trim

4 +Vout

5 Ground

6+Vin

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

Note 1

Thermal reference is defined as the highest temperature

measured at any one of the specified thermal reference points.

See Figure 26: Thermal reference points.

Note 2

The Remote ON/OFF pin is referenced to ground.

Note 3

The SMT15E features a ‘Negative Logic’ Remote ON/OFF

operation. If not using the Remote ON/OFF pin, leave the pin

open (the converter will be on). The Remote ON/OFF pin is

referenced to ground.

The following conditions apply for the SMT15E:

Configuration Converter Operation

Remote pin open circuit Unit is ON

Remote pin pulled low Unit is ON

Remote pin pulled high [Von/off >1.2V] Unit is OFF

A‘Positive Logic’ Remote ON/OFF version is also possible

with this converter. Please consult the factory for details.

Note 4

Thermal reference set up: Unit mounted on an edge card test

board 203mm x 190mm. Test board mounted vertically. For test

details and recommended set-up see Application Note 136.

CAUTION: Hazardous internal voltages and high temperatures.

Ensure that unit is accessible only to trained personnel. The user

must provide the recommended fusing in order to comply with

safety approvals.

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

19 www.artesyn.com

Case Temperature should not exceed 115ºC

Direction of Airflow

Figure 26: Thermal Reference Points

File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006

Longform Datasheet Artesyn Technologies® 2006

The information and specifications contained in this datasheet are

believed to be correct at time of publication. However, Artesyn

Technologies accepts no responsibility for consequences arising

from printing errors or inaccuracies. Specifications aresubject to

change without notice. No rights under any patent accompany the

sale of any such product(s) or information contained herein.

SMT15E Series | 15 A DC-DC

EClass Non-Isolated DC-DC Converters

NORTH AMERICA

e-mail: sales.us@artesyn.com

%800 769 7274

%+508 628 5600

EUROPEAN LOCATIONS

e-mail: sales.europe@artesyn.com

IRELAND

%+353 24 93130

AUSTRIA

%+43 1 80150

FAR EAST LOCATIONS

e-mail: sales.asia@artesyn.com

HONG KONG

%+852 2699 2868

20 www.artesyn.com File Name: lf_smt15e_05.pdf Rev (02): 04 Jan 2006