Signal Relays AXICOM P2 Relay V23079 nStandard telecom relay (ringing and test access) line 15x7.5mm (.590x.295") nMax. switching current 5A n2 form C bifurcated contacts (2 changeover contacts, 2 CO) nImmersion cleanable nHigh sensitivity for low power consumption 140mW/ 70mW nSingle coil version with surge voltage resistance between contact and coil: 2.5kV (2/10s) meets the Telcordia Requirement GR-1089, 1.5kV (10/160s) meets FCC Part 68 Typical applications Communications equipment linecard application (ringing and test access), PABX, voice over IP, office equipment, measurement and control equipment, automotive equipment as CAN bus, keyless entry, speaker switch, medical equipment, consumer electronics, set top boxes, HiFi nSlim P2 V23079 ZRelay Magnetic system Coil voltage3.4range Max. coil temperature 3.2 3 Thermal resistance 2 form C (CO) 220VDC, 250VAC 2A 2A 60W, 62.5VA AgNi, gold-covered bifurcated contact 100V <10V <50m at 10mA, 20mV 50 operations/s typ. 2ms, max. 4ms typ. 2ms, max. 4ms typ. 2ms, max. 4ms typ. 4ms, max. 6ms typ. 1ms, max. 3ms typ. 5x107 operations typ. 1x107 operations typ. 5x105 operations typ. 1x106 operations typ. 2x105 operations typ. 1x105 operations 110VDC / 0.3A - 33W 30VDC / 2.0A - 60W 120VAC / 0.5A - 60VA 240VAC / 0.25A -60VA 125VAC / 1A NO Side 125VDC / 0.5A NO Side typ. 100x106 operations polarized 2 to 24VDC 70 mW 125C <Umax. 125K/W at 0 A Unom = Other coil voltages on request. * Available only in standard coil configurations 140 mW 2.8 2.6 Umax. at 0 A Umax. at 2 x 1 A Umax. at 2 x 2 A 2.4 2.2 2 1.8 1.6 1.4 1.2 1 Unom. nominal coil voltage 0.8 Uop. min. Urel. min. 0.6 0.4 0.2 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Ambient Temperature [C] Max. DC load breaking capacity 200 mW 2.8 Umax. at 0 A Umax. at 2 x 1 A Umax. at 2 x 2 A 2.6 2.4 06-2020, Rev.0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Coil Voltage [U/Unom] DC voltage [VDC] 2.2 DC current [A] N 2.8 Umax. = U Umax. at 2 x 1 A 2.6 Umax. at 2 x 2 A Coil versions, monostable th 2.4 Coil Rated Operate Limiting Release Coil Rated coil 2.2 co code voltagevoltageVoltagevoltage resistancepower 2 1.8VDCVDCVDCVDC 10% mW U op. min. = Lo 1.63.00 008 2.25 6.50 0.30 64 140 th 1.4 016 4.00 3.00 8.70 0.40 114 140 1.2 011 4.50 3.38 9.80 0.45 145 140 1 Unom. nominal coil voltage Fo 001 3.75 10.90 0.50 178 140 0.85.00 Uop. min. 0.66.00 002 4.50 13.00 0.60 257 140 U rel. min. = Lo 0.49.00 006 6.75 19.60 0.90 578 140 th 0.2 00312.009.00 26.151.201029140 0 005*24.00 -40 -30 -20 -1018.00 0 10 20 30 52.302.404114140 40 50 60 70 80 90 100 110 120 130 140 All figures are given for coil without Temperature pre-energization, [C] at ambient temperature +23C. Ambient Coil Voltage [U/Unom] Technical data of approved types on request Coil Voltage [U/Unom] UL 508 File No. E 111441, UL 60950, IEC/EN60950 IEC Ref. Cert. No. 327 Contact arrangement Max. switching voltage Rated current Limiting continuous current, 85C Switching Power Contact material Contact style Minimum switching voltage Thermoelectrical potential Initial contact resistance Frequency of operation, without load Operate time Set/reset time Release time without diode in parallel with diode in parallel Bounce time Electrical endurance at 12V / 10mA at 6V / 100mA at 60V / 500mA at 30V / 1000mA at 30V / 2000mA at 12V / 5000mA / 25C Contact ratings, UL Mechanical endurance Telecom-, Signal and RF Relays Coil Operating Range Coil Data Approvals Contact Data AXICOM 2 1.8 1.6 1.4 1.2 1 Unom. nominal coil voltage 0.8 op. min. data, `Definitions' secDatasheets,Uproduct Urel. min. tion, application notes and all specifications are subject to change. Datasheets and0.6product data is subject to the 0.4 terms of the disclaimer and all chapters of the `Definitions'0.2section, available at http://relays.te.com/definitions 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Ambient Temperature [C] 1 Signal Relays AXICOM P2 Relay V23079 (Continued) Coil Data (continued) Insulation Data Standard HDV Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Initial dielectric strength Coil versions, bistable between open contacts 1000Vrms1500Vrms Coil Rated Set Limiting Reset Coil Rated coil between contact and coil 1500Vrms1500Vrms code voltagevoltageVoltagevoltage resistancepower between adjacent contacts 1000 Vrms1500Vrms VDCVDCVDCVDC 10% mW Initial surge withstand voltage Bistable, 1 coil according to Telcordia TR-NWT-001089 (2/10s) AXICOM 108 3.00 2.25 9.2 Telecom-, -2.25 70 between open contacts 2000V Rev. E 2500V Signal and128 RF Relays 108-98002 111 4.50 3.38 13.85 -3.38 289 70 between contact and coil 2500V 2500V 101 5.00 3.75 15.33 P2 -3.75 357Relay 70 between adjacent contacts 2500V 2500V V23079 102 6.00 4.50 18.5 -4.50 514 70 according to (10/700 s IEC 60950) 106 9.00 6.75 27.75 -6.75 1157 70 between open contacts 2000V 2500V 103 12.00 9.00 37 -9.00 2057 70 between contact and coil 2500V 2500V Operating 105* Coil 24.00 18.00 Range 74 -18.00 8228 70 between adjacent contacts 2500V 2500V Bistable, 2 coil Initial insulation resistance at 500 Vdc > 109 219 2.00 1.50 4.33 1.50 28 140 Capacitance 2183.4 2.401.80 5.21.8041140 between open contacts max. 1pF 70 mW U Nominal coil voltage nom = 2083.2 3.00 2.25 6.52.2564140 between contact and coil max. 2pF AXICOM 3 Umax. at 0 A 211 4.50 3.38 9.8 Telecom-,3.38 145 140 contacts 1.5pF 2.8 Signal andat RF2Relays Upperadjacent limit of the operative108-98002 range of Rev. max. Umax. = between E Umax. x1A 201 5.00 3.75 10.9 3.75Umax. at 2178 140 Clearance /creepage 2.6 x2A the coil to voltage (limiting voltage) when coils are 2.4 202 6.00 4.50 13 P2 V23079 4.50 257 according IEC / EN 60950 1.3/2.5mm Relay 140 2.2 continously energized 206 9.00 6.75 19.6 6.75 578 140 2 20312.009.00 26.159.001029140 1.8 Uop. min. = Lower limit of the operative range of 205*24.00 18.00 52.318.004114140 Other Data 1.6 Operating All figuresCoil are given for coil withoutRange pre-energization, at ambient temperature +23C. thecompliance: coil voltageEU (reliable operate voltage) Material RoHS/ELV, China RoHS, REACH, Halogen content 1.4 Other coil voltages on request. 1.2 refer to the Product Compliance Support Center at Unom. nominal coil voltage * Available only 1in standard coil configurations Uset min. resp. Ureset min. For latching relays www.te.com/customersupport/rohssupportcenter 3.4 0.8 70 mW -40 to +85C Unom = Ambient Nominaltemperature coil voltage 3.2 Uop. min. 0.6 Urel. min. = Lower limit of the operative range of Category of environmental protection 3 Umax. at 0 A 0.4 2.8 limit the operative range of voltage) Umax. = Upper Umax. at 2 x 1 A coilofvoltage (reliable release IECthe 61810 RT III - wash tight 0.2 2.6 Umax. at 2 x 2 A 0 Vibration resistance (functional) the coil voltage (limiting voltage) when coils35g, are 10 to 1000Hz 2.4 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Shock resistance (functional) 2.2 continously energized Ambient Temperature [C] IEC 60068-2-27 (half sine) 100g 2 1.8 type PCB-THT, Uop. min. =Terminal Lower limit of the operative range of 1.6 SMT long and short terminals the coil voltage (reliable operate voltage) 1.4 2.8 Weight max. 2.8 g 140 mW 1.2 Unom. nominal coil voltage 1 2.6 Resistance to relays soldering THT Ureset min. For latching Usetheat Umax. at 0 A min. resp. 0.8 2.4 IEC 60068-2-20 265C/10s Umax. at 2 x 1 A Uop. min. Umax. at 2 x 2 A 0.6 Urel. min. =Moisture Lower limit of thelevel, operative range of 2.2 sensitive JEDEC J-Std-020E MSL3 0.4 2 related SMT relays and release THT relays the coiltovoltage (reliable voltage) 0.2 0 1.8 packed in orginal dry-packs -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 1.6 Ultrasonic cleaning not recommended Ambient Temperature [C] Packaging/unit 1.4 Coil versions,1.2 high dielectric version, monostable, overmolded THT tubes/2000 pcs. Unom.Operate nominal coil voltage Coil Rated Limiting Release Coil Rated coil THT reel/1500 pcs. 1 2.8 140 mW code voltage voltage Voltage Voltage resistance power SMT reel/2000 pcs. or 2500 pcs. 0.8 2.6 Umax. at10% 0A VDCVDCVDCVDC mW 0.6 Uop. min. 2.4 Umax. at 2 x 1 A 0083.00 2.25 6.10.3045200 0.4 U rel. min. Umax. at 2 x 2 A 2.2 001 5.00 3.75 10.1 0.50 125 200 0.2 2 002 6.00 4.50 12.1 0.60 180 200 0 1.8 -40 -30 -20 -10 0 40 50 60 70 80 90 100 110 120 130 140 006 9.00 6.7510 20 30 18.2 0.90 405 200 1.6 Ambient [C] 003 12.00 9.00 Temperature 24.2 1.20 720 200 1.4 All figures are given for coil without pre-energization, at ambient temperature +23C. 1.2 Other coil voltages on request. Unom. nominal coil voltage 1 200 mW 0.8 2.8 2.6 Uop. min. Umax. at 0 A Urel. min. Umax. at 2 x 1 A 0.6 0.4 2.4 Umax. at 2 x 2 A 0.2 2 Coil Voltage [U/Unom] Coil Voltage [U/Unom] 2.2 2 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Ambient Temperature [C] 1.8 1.6 1.4 200 mW 1.2 2.8 1 Unom. nominal coil voltage Umax. at 0 A Umax. at 2 x 1 A 2.6 0.8 2.4 0.6 Uop. min.at 2 x 2 A Umax. Urel. min. 2.2 0.4 2 0.2 1.8 0 1.6 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Ambient Temperature [C] 1.4 1.2 1 Unom. nominal coil voltage 06-2020, Rev. 0620 Datasheets and product specification Datasheets and product data is subject to the www.te.com 0.8 according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of 0.6 Uop. min. (c) 2015 Tyco Electronics Corporation, only together with the `Definitions' section. the `Definitions' section, available at 0.4 All specifications subject to change. Consult Tyco Electronics for latest specifications.http://relays.te.com/definitions Urel. min. a TE Connectivity Ltd. company 0.2 0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 Ambient Temperature [C] Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 5 of 15 Signal Relays AXICOM P2 Relay V23079 (Continued) Terminal assignment TOP view on component side of PCB Monostable version Bistable version, 1-coil Bistable version, 2-coils Contacts are shown in reset condition. Both coils can be used as either set or reset coils. Contact position might change during transportation and must be reset before use. PCB layout TOP view on component side of PCB THT version SMT, long terminals SMT, short terminals 0,9 0,1 Dimensions 0.50.05 7.20.1 7.20.1 14.50.1 7.20.1 0.50.05 SMT, short terminals 14.50.1 7 14.50.1 7 5.520.15 0.50.05 5.520.15 0.50.05 10.40.15 10.40.15 0.50.05 14.50.1 SMT, long terminals 10.40.15 10.40.15 14.50.1 7.20.1 9.80.19.80.1 3.25-0.25 3.25-0.25 9.40.15 0.50.05 7.40.15 9.40.15 Overmolded coil, high dielectric version THT version SMT, long terminals 7.40.15 SMT, short terminals 7.20.1 14.60.1 7 14.60.1 7.20.1 14.60.1 7.20.1 14.60.1 7 0.45 0.50.05 0.50.05 06-2020, Rev.0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company 0.50.05 5.52 0.50.05 5.52 0.50.05 9.90.15 9.90.15 14.60.1 9.50.19.50.1 3.25-0.25 3.25-0.25 7.20.1 0.45 14.60.1 9.90.19.90.1 0.55-0.15 0.55-0.15 Standard coil 14.50.1 THT version 9.40.15 0.50.05 9.40.15 Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions 7.40.15 7.40.15 Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 3 5 Signal Relays AXICOM P2 Relay V23079 (Continued) Processing Recommended soldering conditions Vapour phase soldering 20 to 40s 240C full line: typical dotted line: process limits Temperature [C] 180C forced cooling 130C external preheating 100C Vapour phase soldering temperature/time profile (lead and housing peak temp.) Time [s] Recommended reflow soldering profile Infrared soldering Temperature [C] temperature/time profile (lead and housing peak temp.) Time [s] Packing THT-tubes Reel dimensions 4 06-2020, Rev. 0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. Signal Relays AXICOM P2 Relay V23079 (Continued) SMT - LONG TERMINALS, OVERMOLDED COIL USED ON 0.6 3 A x ma R0 .3 ma x. max. 40.2 .3 m 7 - DIST 7 3306-7 (3/11) - P 8 LTR 8 - 7 - 1 - REVISION RECORD P 6 LTR 13.12.2005 9193 9121 25.05.1998 9188 9151 DATE DWN 5 REVISION RECORD 7 6 26.3.2012 ANGLES - 13.12.2005 - APVD SURFACE TEXTURE 25.05.1998 DATE 0 1 2 3 4 PLC PLC PLC PLC PLC ZC 0.1 0.01 PH0.001 0.0001 9188 9151 4 DWN 5 Petr Hofman mm APVD 0 PLC P2L2/P2L3/FU2 --0.1Blister tape short terminals Petr Hofman 1 PLC SIZE 2 PLC 3 PLC 4 PLC - APVD SURFACE TEXTURE A3 3 DRAWING NO 4 SHEET 0.01 NAME 0.001 C23303-A079-C120 0.0001 2 - 0.6 x. R 0.3 ma C23303-A079-C121 10.4+0.3 0 THIS DRAWING IS A CONTROLLED DOCUMENT 1.750.1 1.90.2 ( 1.5 0.1 1.5) B-B 3 C A-A 15.40.2 3 . 3 max. 3 MATERIAL 1.2+0.2 0 1.5 0.1 3 - - 1 90.2 - P 8 - B LTR REVISION RECORD 7 40.1 A DWN Zdenek Cu ma30.03.2012 x. 3 80.2 2 - DIST - 26.3.2012 160.15 LOC HEAT TREAT A max 6 ZC PH 9122 25.05.1998 9.10.2 PH 9122 DATE DWN mm PH 17.06.2011 ANGLES 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC - APVD 0.1 0.01 0.001 0.0001 Petr Hofm NAME P2L3 SCALE 4:1 - APVD SURFACE TEXTURE S roztec transportnich otv 4 3 distance of transport ho 4x10=400.2mm 4x11=440.2mm 4x12=480.2mm 5 1.5 0.1 CHK TOLERANCES UNLESS OTHERWISE SPECIFIED: DIMENSIONS: - -9 PS conductivity 10 S/m 40.2B B 1.30.2 REV 0.6 1 1 11.50.1 OF C 10.9+0.3 0 1 ma x. R0 .3 (3.6) SHEET 26.3.2012 (48) 20.1 A 1 TE Connectivity CHK NAME 4:1 ANGLES Zdenek Curda 26.3.2012 TOLERANCES UNLESS OTHERWISE SPECIFIED: DIMENSIONS: 4.40.2 4.40.2 DWG NO APVD SCALE 9193 9121 DWN - CHK (8) REV 1 OF B HEAT TREAT -9 PS conductivity 10 S/m 3 20.1 TE Connectivity REV 1 1 8 P2L2/P2L3/FU2 - Blister tape short terminals SCALE SIZE A3 4:1 OF 1 DRAWING NO C23303-A079-C120 3 SHEET 1 2 OF REV 8 1 1 11.50.1 A 15.40.2 8 Zdenek Curda TOLERANCES UNLESS OTHERWISE SPECIFIED: mm PH MATERIAL max. 12.20.2 240.3 - 3306-7 (3/11) THT - REEL 1 LOC ZC B 40.1 3306-7 (3/11) 26.3.2012 DWN 120.15 26.3.2012 1 A 1.2+0 0 06-2020, Rev.0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). - THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). LOC B - m 1.5 0.1 120.15 DIMENSIONS: 8 1.2+0.2 0 1.5 0.1 0.3 ax. R A 3 A 120.2 D 1.750.1 0.3 ax. R 1.2+0.2 0 B (3.6) (3.6) 2.20.2 15.40.2 1.30.2 A 1.90.2 1.30.2 . 3 max A 1.30.2 A B-B 2.20.2 A 15.40.2 240.3 240.3 11.50.1 11.50.1 B-B x. 100.2 240.3 DATE 20.1 ma TE Connectivity SHEET A3 4:1 NAME max. 3 B 40.2 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). - 4.50.2 2 PLC 3 PLC 4 PLC - 1.90.2 0.1 0.01 0.001 0 PLC roztec transportnich P2L3 otvoru 1.5 tape long2terminals 4 0.0001 3 - Blister SCALE SIZE DRAWING NO distance of transport holes 1.5 DWN APVD roztec transportnich otvoru 1.5 SURFACE TEXTURE 4:1 distance of transport holes 1.5 A3 C23303-A079-C121 distance of transport holes 4x10=400.2mm 1.5 4x10=400.2mm 4x11=440.2mm 4x10=400.2mm 5 4x11=440.2mm 4 4x12=480.2mm 3 2 4x11=440.2mm 4x12=480.2mm 5 4x12=480.2mm DIST (3.6) 15.40.2 15.40.2 - ANGLES 1 PLC APVD SURFACE TEXTURE PH 1.59122 0.1ANGLES - A-A 2:1 P2L3 - Blister30.3.2012 tape long terminals SCALE SIZE DRAWING NO 2:1 Petr Hofman 2:1 C23303-A079-C121 1.90.2 DWN PH 9122 25.05.1998 2:1 NAME (3.6) 1.5 0.1 6 20.1 DATE 17.06.2011 HEAT TREAT APVD C23303-A079-C120 B REVISION RECORD 40.1 9.10.2 6 PH 9122 9.10.2 REVISION RECORD - - TE Connectivity (3.6) LTR mm DWG NO B LTR 40.17 ZC PH 25.05.1998 30.03.2012 - P 90.2 7 DIMENSIONS: THIS DRAWING IS A CONTROLLED DOCUMENT - PH 39122 MATERIAL . 3 - 1 max. D HEAT TREAT -9 PS conductivity 10 S/m - max P 2 1.30.2 0.6 R0 .3 x. ma 17.06.2011 80.2 30.3.2012 Petr Hofman CHK 4.50.2 - - Zdenek Curda APVD 0 PLC 0.1 1 PLC TOLERANCES UNLESS 0.01 2 PLC SPECIFIED: OTHERWISE 0.001 3 PLC 0.0001 4 PLC MATERIAL -9 PS conductivity 10 S/m 30.3.2012 - mm 1.90.2 2 Zdenek Curda CHK TOLERANCES UNLESS DWN OTHERWISE SPECIFIED: DIMENSIONS: PH 30.3.2012 DWN - .3- 0.3 max. R 1.2+0.2 0 1.5 0.1 ZC USED ON max. R0 1.2+0.2 0 1.5 0.1 30.03.2012 USED ON 1.90.2 - - 8 1.750.1 8 (3.6) 2.20.2 2.20.2 3 B (3.6) - 3 3 1 max SMT - SHORT TERMINALS 90.2 . 3 80.2 DIST 1.750.1 - 40.2 40.2 LOC max. R0 .3 10.9+0.3 0 160.15 max.160.15 3 . 3 max x. B max. 3 ma 10.9+0.3 0 A-A 3306-7 (3/11) 6-7 (3/11) AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT AUTHORIZATION FROM TE (www.TE.com). A-A C23303-A079-C120 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED DWG TO ANYONE, NO OTHER THAN TE IS PERSONNEL, WITHOUT THIS DRAWING A CONTROLLED DOCUMENT AUTHORIZATION FROM TE (www.TE.com). C23303-A079-C120 DWG NO THIS DRAWING IS A CONTROLLED DOCUMENT OC IST 0.6 240.3 240.3 11.50.1 11.50.1 B-B B 2:1 mam x.a3x. B-B 1.90.2 1.5) C 2:1 1.90.2 ( 1.5 0.1 20.1 40.1 distance of transport holes 1.5 4x10=400.2mm 4x11=440.2mm 4x12=480.2mm 1.5) 3 1.750.1 C ( 1.5 0.1 (48) (8) D A 2:1 (48) 20.1B D 2:1 A 3 100.2 SMT - LONG TERMINALS, STANDARD12.20.2 COIL 120.2 (8) - A 12.20.2 m ax. 3 120.2 40.1 - 0.6 R0 .3 x. ma x. C23303-A079-C121 USED ON ma max. 3 B 1.750.1 A-A 100.2 THIS DRAWING IS A CONTROLLED DOCUMENT DWG NO 40.2 max. 3 10.4+0.3 0 10.4+0.3 0 A-A B 1.5 0.1 120.15 TOLERANC OTHERWISE DIMENSIONS: LOC - 8 - 7 - 1 to Datasheets and product data is subject the - of the disclaimer and all chapters of terms the `Definitions' 8 section, available at 7 http://relays.te.com/definitions DIST P 3306-7 (3/11) LTR 26.3.2012 13.12.2005 ZC mm PH 9193 9121 9188 9151 Datasheets, product 25.05.1998 data, `Definitions' sec- tion, application notes and all specifications are subject to change. 6 5 0 1 2 3 4 5 PLC PLC PLC PLC PLC ANGLES REVISION RECORD DATE DWN APVD SURFACE TEXTURE - 4 Signal Relays AXICOM P2 Relay V23079 (Continued) Product code structure Typical product code V23079 A 1 001 B 301 Type V23079 Signal Relay P2 Series Version A THT, monostable D SMT, monostable, long term. G SMT, monostable, short term. B THT, latching, 2 coils E SMT, latching, 2 coils long term. H SMT, latching, 2 coils short term. C THT, latching, 1 coil F SMT, latching, 1 coil long term. J SMT, latching, 1 coil short term. Coil design 1 Standard coil (not for high dielectric version) 2 Overmolded coil Coil Coil code: please refer to coil versions table Version B Standard version X Special version (High dielectric, THT packed in reel) Contacts for standard versions 301 2 form C contacts (2 CO), AgNi +Au Contacts for dielectric versions 07* 2 form C contacts (2 CO), AgNi +Au Packing X1** THT version packed in reel * any digit Product code V23079-A1001-B301 V23079-A1006-B301 V23079-A1005-B301 V23079-A1008-B301 V23079-A2008-B301 V23079-A2011-B301 V23079-A2001-B301 V23079-A2002-B301 V23079-A2006-B301 V23079-A2003-B301 V23079-B1218-B301 V23079-B1208-B301 V23079-B1211-B301 V23079-B1201-B301 V23079-B1202-B301 V23079-B1206-B301 V23079-B1203-B301 V23079-B1205-B301 V23079-B2219-B301 V23079-B2218-B301 V23079-B2208-B301 V23079-B2201-B301 V23079-C1108-B301 V23079-C1111-B301 V23079-C1101-B301 V23079-C1102-B301 V23079-C1106-B301 6 06-2020, Rev. 0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Version THT Coil design Standard Coil type Monostable Overmolded Standard Bistable, 2 coils Overmolded Standard Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Bistable, 1 coils Coil voltage 5VDC 9VDC 24VDC 3VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 2.4VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 24VDC 2VDC 2.4VDC 3VDC 5VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Part number 1393788-3 2-1393788-0 1-1393788-6 2-1393788-2 6-1419120-6 3-1393789-9 3-1393789-5 3-1393789-6 3-1393789-8 3-1393789-7 1422002-8 4-1393788-1 4-1393788-2 3-1393788-3 3-1393788-5 3-1393788-9 3-1393788-6 3-1393788-7 1-1422002-2 1-1422002-1 1-1422002-0 1422002-9 5-1393788-3 5-1393788-4 4-1393788-5 4-1393788-7 5-1393788-1 Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. Signal Relays AXICOM P2 Relay V23079 (Continued) Product code V23079-D1001-B301 V23079-D1003-B301 V23079-D1006-B301 V23079-D1005-B301 V23079-D1008-B301 V23079-D1011-B301 V23079-D2008-B301 V23079-D2011-B301 V23079-D2001-B301 V23079-D2002-B301 V23079-D2006-B301 V23079-D2003-B301 V23079-E1219-B301 V23079-E1218-B301 V23079-E1208-B301 V23079-E1211-B301 V23079-E1201-B301 V23079-E1202-B301 V23079-E1206-B301 V23079-E1203-B301 V23079-E1205-B301 V23079-E2219-B301 V23079-E2201-B301 V23079-E2208-B301 V23079-E2218-B301 V23079-F1108-B301 V23079-F1111-B301 V23079-F1101-B301 V23079-F1102-B301 V23079-F1106-B301 V23079-F1103-B301 V23079-F1105-B301 V23079-G1001-B301 V23079-G1005-B301 V23079-G2008-B301 V23079-G2016-B301 V23079-G2011-B301 V23079-G2001-B301 V23079-G2002-B301 V23079-G2006-B301 V23079-G2003-B301 V23079-H1208-B301 V23079-H1211-B301 V23079-H1201-B301 V23079-H1202-B301 V23079-H1206-B301 V23079-H1203-B301 V23079-H1205-B301 V23079-J1108-B301 V23079-J1111-B301 V23079-J1101-B301 V23079-J1102-B301 V23079-J1103-B301 V23079-J1105-B301 V23079-G2008-X079 V23079-G2001-X071 V23079-G2002-X072 V23079-G2006-X073 V23079-G2003-X074 V23079-A2003-X074 V23079-A2008-X079 V23079-A2008-X101 V23079-A2011-X102 V23079-A2001-X103 V23079-A2002-X104 V23079-A2006-X105 V23079-A2003-X106 V23079-B2219-X107 V23079-B2218-X108 V23079-B2208-X109 V23079-B2201-X110 Version SMT, long pins Coil design Standard Coil type Monostable Overmolded Standard Bistable, 2 coils Overmolded Standard SMT, short pins Bistable, 1 coil Monostable Overmolded Standard Bistable, 2 coils Bistable, 1 coil SMT, short pins High dielectric Overmolded Monostable THT THT packed in reel 06-2020, Rev.0620 www.te.com (c) 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Overmolded Bistable, 2 coils Datasheets and product specification according to IEC 61810-1 and to be used only together with the `Definitions' section. Coil voltage 5VDC 12VDC 9VDC 24VDC 3VDC 4.5VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 2VDC 2.4VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 24VDC 2VDC 5VDC 3VDC 2.4VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 24VDC 5VDC 24VDC 3VDC 4VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 24VDC 3VDC 4.5VDC 5VDC 6VDC 12VDC 24VDC 3VDC 5VDC 6VDC 9VDC 12VDC 12VDC 3VDC 3VDC 4.5VDC 5VDC 6VDC 9VDC 12VDC 2VDC 2.4VDC 3VDC 5VDC Datasheets and product data is subject to the terms of the disclaimer and all chapters of the `Definitions' section, available at http://relays.te.com/definitions Part number 5-1393788-5 5-1393788-7 5-1393788-9 5-1393788-8 6-1393788-1 6-1393788-2 4-1393789-7 4-1393789-8 4-1393789-3 4-1393789-4 4-1393789-6 4-1393789-5 1-1422007-0 1422007-5 7-1393788-1 7-1393788-2 6-1393788-8 1393789-5 1393789-9 6-1393788-9 7-1393788-0 1422007-6 1422007-7 1422007-8 1422007-9 7-1393788-5 1-1393789-4 7-1393788-3 1-1393789-0 1-1393789-2 7-1393788-4 1-1393789-1 7-1393788-6 7-1393788-8 5-1393789-4 1393790-5 5-1393789-5 4-1393789-9 5-1393789-0 5-1393789-3 5-1393789-1 2-1393789-4 8-1393788-4 2-1393789-0 2-1393789-1 2-1393789-3 8-1393788-3 2-1393789-2 2-1393789-9 3-1393789-0 2-1393789-5 2-1393789-6 2-1393789-7 2-1393789-8 1422006-5 1422006-1 1422006-2 1422006-3 1422006-4 1422025-7 1-1422025-1 6-1419170-9 3-1393790-1 3-1393790-2 3-1393790-3 3-1393790-4 3-1393790-5 1-1422003-0 1-1422003-1 1-1422003-2 1422003-3 Datasheets, product data, `Definitions' section, application notes and all specifications are subject to change. 7