K1/K2 SEALED, ILLUMINATED ROCKER SWITCHES SNAP-IN ROCKERS LOW COST, SNAP-IN ROCKER FOR WET AND DUSTY ENVIRONMENTS; 1 AND 2 POLES The K series rockers are rugged, high performance sealed switches designed for use under severe conditions found in marine, appliance, heavy equipment and industrial control applications. They are designed to meet the international submersion specification level IP68. An optional panel seal is also available. The K1 series is offered in single pole configuration while the K2 series is available in single and double pole configurations. Both series offer illuminated models. Illumination can be independent or dependent of the switch position or a combination of both. A choice of red, green, clear or amber colored lens are offered in illuminated models. Illumination options include incandescent, LED or neon light sources. K1 Series Single Pole ROCKER SWITCHES Mounting is simple and quick; snaps into panel from the front. The OTTO snap-in design supports a variety of panel thicknesses with just one cut-out size specified. A choice of models are offered to handle power levels to 16 amperes, 1/2 HP and low level electronic switching applications. OTTO can provide custom colors upon request. Value-added assemblies with wire leads are also available. Please consult the factory for assistance. Quality Features: K2 Series Single & Double Pole (R) * Withstands direct water spray * Submersible. Designed to meet IP68 * Fits industry standard panel openings for drop-in replacement of panel sealed and unsealed switches Standard Characteristics/Ratings: * Snap-in feature accommodates a wide range of panel cut-outs Mechanical Life: 100,000 cycles, minimum Seal: Watertight, submersible to IP68 OPERATIONAL: Temperature Range: -30C to +85C * Switches up to 16 amps Button & Case: Thermoplastic * UV and Solvent resistant Terminals: Brass alloy * Withstands extreme shock & vibration Contacts: Fine Silver/Silver Cad. oxide * Custom legends available * 2- & 3-position, momentary and maintained action * Incandescent, LED and neon illumination with independent and dependent light source options * UL and CSA recognized ELECTRICAL: (at 28 VDC or 125 VAC) RATING LIFE (Min.) 16A 25,000 cycles Resistive 10A 50,000 cycles Inductive 10A 25,000 cycles Lamp 5A 25,000 cycles Motor 1/2HP 25,000 cycles LOAD Resistive Dielectric Withstand: 1050V rms -- Except across light terminals Specifications Subject To Change Without Notice www.ottoexcellence.com 77 K1 SNAP-IN ROCKERS SEALED, ILLUMINATED ROCKER SWITCHES LOW COST, SNAP-IN ROCKER FOR WET AND DUSTY ENVIRONMENTS; 1 AND 2 POLES K 1 S er ie s PA RT K1 X X X Terminal Style/ Switch Rating Actuator Color/Style Switch Action/Circuit A. B. C. D. E. F. G. H. A. Red/Rocker B. Black/Rocker C. White/Rocker D. Red/Paddle E. Black/Paddle F. White/Paddle G. Red/Rocker Pinned H. Black/Rocker Pinned J. White/Rocker Pinned K. Red/Short Paddle Pinned L. Black/Short Paddle Pinned M. White/Short Paddle Pinned N. Red/Standard Paddle Pinned P. Black/Standard Paddle Pinned R. White/Standard Paddle Pinned T. Red/Short Paddle U. Black/Short Paddle V. White/Short Paddle Q.C/Standard Screw/Standard Solder/Standard Q.C./Low level Screw/Low level Solder/Low level P.C. Pin/Standard P.C. Pin/Low level Position Position Position Code "A" "B" "C" Circuit A. ON None OFF SPST B. ON None ON SPDT C. MOM-ON None OFF SPST D. MOM-ON None ON SPDT E. MOM-ON OFF MOM-ON SPDT F. ON OFF ON SPDT G. MOM-ON OFF ON SPDT Position "A" Position "B" Position "C" NOTES * No momentary switches with dependent lights * Neon lamps only to be coded with clear or Amber lenses * LED lenses must be clear or same color as LED * No dependent light in OFF positions * All legends will be white except for actuator codes C, F, J, M, R, and V will be black * K1 panel plug part number C401561 D_ 78 OTTO 2007 Full Line Catalog Specifications Subject To Change Without Notice K1 SNAP-IN ROCKERS SEALED, ILLUMINATED ROCKER SWITCHES LOW COST, SNAP-IN ROCKER FOR WET AND DUSTY ENVIRONMENTS; 1 AND 2 POLES NUMBERING CODE X X Light Type Lens Color Position "A" A. No Lens B. Red C. Green D. Amber E. Clear Position "C" A. No Lens B. Red C. Green D. Amber E. Clear X X Light/Circuit Location Legend and Orientation A. No Light A. None Dependent Light ON in Position "A" Wired to Terms 1 & 3 Dependent Light ON in Position "A" Wired to Terms 1 & 3 Dependent Light ON in Position "C" Wired to Terms 2 & 4 Dependent Light ON in Position "C" Wired to Terms 2 & 4 Dependent Light ON in Position "A" Wired to Terms 1 & 3 Independent Light ON in Position "C" Wired to Terms 3 & 4 Independent Light at Position "A" Wired to Terminals 3 & 4 Independent Light at Position "A" Wired to Terminals 3 & 4 Dependent Light ON in Position "C" Wired to Terms 2 & 4 Independent Light at Position "C" Wired to Terminals 3 & 4 ROCKER SWITCHES A. No Light B. 6 V Incandescent C. 12 V Incandescent D. 24 V Incandescent E. 125 VAC Neon F. 250 VAC Neon G. 2 V Red LED H. 2 V Green LED J. 2 V Amber LED K. 6 V Red LED L. 6 V Green LED M. 6 V Amber LED N. 12 V Red LED P. 12 V Green LED Q. 12 V Amber LED R. 24 V Red LED S. 24 V Green LED T. 24 V Amber LED X D= Dependent I = Independent * LED anode (+) terminal number shown in bold * Light on OFF side must be independent ON-NONE-Off * Contact factory for multiple light types in the same switch K1 SERIES Specifications Subject To Change Without Notice Panel cut out dimensions are for reference only. Differences in panel material and thickness may require changes to the panel cut out for optimum fit. Optional Panel Gasket P/N 807039-1 www.ottoexcellence.com 79 K2 SNAP-IN ROCKERS SEALED, ILLUMINATED ROCKER SWITCHES LOW COST, SNAP-IN ROCKER FOR WET AND DUSTY ENVIRONMENTS; 1 AND 2 POLES K 2 S er ie s PA RT K2 X X Terminal Style/ Switch Rating Actuator Color/Style A. B. C. D. E. F. A. B. C. D. E. F. G. Q.C/Standard Screw/Standard Solder/Standard Q.C./Low level Screw/Low level Solder/Low level H. J. K. L. For custom colors, contact factory. M. N. P. R. K2 SERIES X Red Rocker Black Rocker White Rocker Red Paddle Black Paddle White Paddle Red/Short Paddle/Pinned Black/Short Paddle/Pinned White/Short Paddle/Pinned Red Paddle Pinned/STD Black Paddle Pinned/STD White Paddle Pinned/STD Red Rocker Pinned Black Rocker Pinned White Rocker Pinned X Switch Action/Circuit Position Position Position Code A. B. C. D. E. F. G. H. J. K. L. M. N. P. Q. R. S. T. U. V. Light Type "A" "B" "C" Circuit ON ON MOM-ON MOM-ON MOM-ON ON MOM-ON ON ON MOM-ON MOM-ON MOM-ON ON MOM-ON ON OFF ON OFF ON ON None None None None OFF OFF OFF None None None None OFF OFF OFF None None None None OFF OFF OFF ON OFF ON MOM-ON ON ON OFF ON OFF ON MOM-ON ON ON MOM-ON MOM-ON MOM-ON MOM-ON MOM-ON MOM-ON SPST SPDT SPST SPDT SPDT SPDT SPDT DPST DPDT DPST DPDT DPDT DPDT DPDT SPDT SPST DPDT DPST SPDT DPDT Position "A" A. B. C. D. E. F. G. H. J. K. L. M. N. P. Q. R. S. T. Position "B" No Light 6 V Incandescent 12 V Incandescent 24 V Incandescent 125 VAC Neon 250 VAC Neon 2 V Red LED 2 V Green LED 2 V Amber LED 6 V Red LED 6 V Green LED 6 V Amber LED 12 V Red LED 12 V Green LED 12 V Amber LED 24 V Red LED 24 V Green LED 24 V Amber LED Position "C" Panel cut out dimensions are for reference only. Differences in panel material and thickness may require changes to the panel cut out for optimum fit. Optional Panel Gasket P/N 807038-1 Recommended panel thickness: .125 Optimum thickness (.025 min - .187 max) 80 OTTO 2007 Full Line Catalog Specifications Subject To Change Without Notice K2 SEALED, ILLUMINATED ROCKER SWITCHES SNAP-IN ROCKERS LOW COST, SNAP-IN ROCKER FOR WET AND DUSTY ENVIRONMENTS; 1 AND 2 POLES NUMBERING CODE X X Lens Color Position "A" A. B. C. D. E. No Lens Red Green Amber Clear X X Light/Circuit Location Legend and Orientation A. No Light A. None Position "C" A. B. C. D. E. No Lens Red Green Amber Clear Dependent Light ON in Position "A" Wired to Terms 1 & 7 Independent Light at Position "A" Wired to Terms 7 & 8 Independent Light ON in Position "A" Wired to Terms 7 & 8 Dependent Light ON in Position "C" Wired to Terms 2 & 8 Dependent Light ON in Position "A" Wired to Terminals 1 & 7 Independent Light at Position "C" Wired to Terms 7 & 8 Independent Light ON in Position "A" Wired to Terms 3 & 7 Independent Light ON at Position "C" Wired to Terms 4 & 8 Not available in Double Throw/ Double Pole ROCKER SWITCHES Dependent Light ON in Position "C" Wired to Terms 2 & 8 Dependent Light ON in Position "A" Wired to Terms 1 & 7 Dependent Light ON in Position "C" Wired to Terms 2 & 8 D= Dependent I = Independent Independent Light at Position "C" Wired to Terms 7 & 8 NOTES * No momentary switches with dependent lights * Neon lamp only to be coded with clear or amber lenses * LED lenses must be clear or same color as the lens * No dependent light in OFF positions * All legends will be White except for actuator code C, F, J, M & R will be Black * K2 Connector part number C801765 * Recommended Quick Connect Terminals: * LED anode (+) terminal number shown in bold - AMP 60253-2 for 12-16 AWG wire with .160"-.210" insulation OD * Light on OFF side must be independent - AMP 42100-2 for 14-18 AWG wire with .100"-.170" insulation OD * Contact factory for multiple light types in the same switch * K2 Panel Plug part number C100695-2 Specifications Subject To Change Without Notice www.ottoexcellence.com 81