LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 Dual Micropower Rail-To-Rail Input CMOS Comparator with Open Drain Output Check for Samples: LMC6772 FEATURES DESCRIPTION 1 (Typical Unless Otherwise Noted) 2 * * * * * * * * Low Power Consumption (Max): IS = 10 A/comp Wide Range of Supply Voltages: 2.7V to 15V Rail-to-Rail Input Common Mode Voltage Range Open Drain Output Short Circuit Protection: 40 mA Propagation Delay (@VS = 5V, 100 mV Overdrive): 5 s LMC6772Q is AEC-Q Qualified LMC6772Q has -40C to 125C Temperature Range APPLICATIONS * * * * * * * Laptop Computers Mobile Phones Metering Systems Hand-Held Electronics RC Timers Alarm and Monitoring Circuits Window Comparators, Multivibrators The LMC6772 is an ultra low power dual comparator with a maximum 10 A/comparator power supply current. It is designed to operate over a wide range of supply voltages, with a minimum supply voltage of 2.7V. The common mode voltage range of the LMC6772 exceeds both the positive and negative supply rails, a significant advantage in single supply applications. The open drain output of the LMC6772 allows for wired-OR configurations. The open drain output also offers the advantage of allowing the output to be pulled to any voltage rail up to 15V, regardless of the supply voltage of the LMC6772. The LMC6772 is targeted for systems where low power consumption is the critical parameter. Ensured operation at supply voltages of 2.7V and rail-to-rail performance makes this comparator ideal for batterypowered applications. Refer to the LMC6762 datasheet for a push-pull output stage version of this device. Connection Diagram 8-Pin PDIP/SOIC/VSSOP - Top View See Package Number P0008E/D0008A/DGK0008A 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1995-2013, Texas Instruments Incorporated LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) Value ESD Tolerance (2) Unit 1.5 kV Differential Input Voltage (V+)+0.3V to (V-)-0.3 V Voltage at Input/Output Pin (V+)+0.3V to (V-)-0.3 V Supply Voltage (V+-V-) 16 V Current at Input Pin (3) 5 mA 30 mA 40 mA 260 C -65C to 150 C 150 C Current at Output Pin (4) (5) Current at Power Supply Pin, LMC6772 Lead Temperature (Soldering, 10 seconds) Storage Temperature Range Junction Temperature (6) (1) (2) (3) (4) (5) (6) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the electrical characteristics. Human body model, 1.5 k in series with 100 pF. The output pins of the two comparators (pin 1 and pin 7) have an ESD tolerance of 1.5 kV. All other pins have an ESD tolerance of 2 kV. Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings. Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30 mA over long term may adversely affect reliability. Do not short circuit output to V+, when V+ is > 12V or reliability will be adversely affected. The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/JA. All numbers apply for packages soldered directly into a PC board. Operating Ratings (1) Value Supply Voltage Unit 2.7 VS 15 V Junction Temperature Range -40C TJ 85 C -40C TJ 125 C 8-Pin PDIP 100 C/W 8-Pin SOIC 172 C/W LMC6772AI, LMC6772BI LMC6772Q Thermal Resistance (JA) (1) 2 Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the electrical characteristics. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 2.7V Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 2.7V, V- = 0V, VCM = V+/2. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TCVOS Input Offset Voltage Temperature Drift Input Offset Voltage Average Drift Conditions Typ (1) 3 See (3) LMC6772AI LMC6772BI Limit (2) Limit (2) 5 8 15 18 LMC6772Q Limit (2) Units 10 13 mV max 2.0 V/C 3.3 V/Mont h IB Input Current 0.02 pA IOS Input Offset Current 0.01 pA CMRR Common Mode Rejection Ratio 75 dB PSRR Power Supply Rejection Ratio 1.35V < VS < 7.5V 80 dB AV Voltage Gain (By Design) 100 dB VCM Input Common-Mode Voltage Range CMRR > 55 dB 3.0 2.9 2.7 2.9 2.7 2.9 2.7 V min -0.3 -0.2 0.0 -0.2 0.0 -0.2 0.2 V max VOL Output Voltage Low ILOAD = 2.5 mA 0.2 0.3 0.4 0.3 0.4 0.3 0.45 V max IS Supply Current For Both Comparators (Output Low) 12 20 25 20 25 20 25 A max ILeakage Output Leakage Current VIN(+) = 0.5V, VIN(-) = 0V, VO = 15V 0.1 500 500 500 1000 nA (1) (2) (3) Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Input offset voltage Average Drift is calculated by dividing the accelerated operating life drift average by the equivalent operational time. The input offset voltage average drift represents the input offset voltage change at worst-case input conditions. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 3 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com 5.0V and 15.0V Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 5.0V and 15.0V, V- = 0V, VCM = V+/2. Boldface limits apply at the temperature extremes. Symbol Parameter Conditions VOS Input Offset Voltage TCVOS Input Offset Voltage Temperature V+ = 5V Drift V+ = 15V IB Typ (1) 3 LMC6772AI LMC6772BI Limit (2) Limit (2) 5 8 15 18 LMC6772Q Limit (2) Units 10 13 mV max V/C 2.0 4.0 Input Offset Voltage Average Drift V+ = 5V (3) 3.3 V+ = 15V (3) 4.0 Input Current V = 5V 0.04 pA pA + IOS Input Offset Current V = 5V 0.02 CMRR Common Mode Rejection Ratio V+ = 5V 75 V+ = 15V 82 V/Mont h dB PSRR Power Supply Rejection Ratio 2.5V < VS < 5V 80 AV Voltage Gain (By Design) 100 VCM Input Common-Mode Voltage Range V+ = 5.0V CMRR > 55 dB 5.3 5.2 5.0 5.2 5.0 5.2 5.0 V min -0.3 -0.2 0.0 -0.2 0.0 -0.2 0.0 Vmax 15.3 15.2 15.0 15.2 15.0 15.2 15.0 V min -0.3 -0.2 0.0 -0.2 0.0 -0.2 0.0 V max V+ = 5V ILOAD = 5 mA 0.2 0.4 0.55 0.4 0.55 0.4 0.55 V max V+ = 15V ILOAD = 5 mA 0.2 0.4 0.55 0.4 0.55 0.4 0.55 V max 20 25 20 25 20 25 A max + V = 15.0V CMRR > 55 dB VOL Output Voltage Low IS Supply Current For Both Comparators (Output Low) 12 ISC Short Circuit Current V+ = 15V, Sinking, VO = 12V (4) 45 (1) (2) (3) (4) 4 dB dB mA Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Input offset voltage Average Drift is calculated by dividing the accelerated operating life drift average by the equivalent operational time. The input offset voltage average drift represents the input offset voltage change at worst-case input conditions. Do not short circuit output to V+, when V+ is > 12V or reliability will be adversely affected. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 AC Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V+/2. Boldface limits apply at the temperature extreme. Symbol Parameter Typ (1) Conditions LMC6772AI Limit (2) LMC6772BI Limit (2) Units tRISE Rise Time f = 10 kHz, CL = 50 pF, Overdrive = 10 mV (3) 0.3 s tFALL Fall Time f = 10 kHz, CL = 50 pF, Overdrive = 10 mV (3) 0.3 s tPHL Propagation Delay (High to Low) f = 10 kHz, CL = 50 pF (3) 10 mV 10 s 100 mV 4 s 10 s V+ = 2.7V, f = 10 kHz, tPLH Propagation Delay (Low to High) 10 mV CL = 50 pF (3) 100 mV 4 s f = 10 kHz, CL = 50 pF (3) 10 mV 10 s 100 mV 4 s 8 s 4 s + V = 2.7V, f = 10 kHz, CL = 50 pF (3) (1) (2) (3) 10 mV 100 mV Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. CL inlcudes the probe and jig capacitance. The rise time, fall time and propagation delays are measured with a 2V input step. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 5 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics + V = 5V, Single Supply, TA = 25C unless otherwise specified 6 Supply Current vs. Supply Voltage (Output High) Supply Current vs. Supply Voltage (Output Low) Figure 1. Figure 2. Input Current vs. Common-Mode Voltage Input Current vs. Common-Mode Voltage Figure 3. Figure 4. Input Current vs. Common-Mode Voltage Input Current vs. Temperature Figure 5. Figure 6. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 Typical Performance Characteristics (continued) + V = 5V, Single Supply, TA = 25C unless otherwise specified VOS vs VCM, VS = 2.7V VOS vs VCM, VS = 5V Figure 7. Figure 8. VOS vs VCM, VS = 15V Output Voltage vs. Output Current (Sinking) Figure 9. Figure 10. Output Voltage vs. Output Current (Sinking) Output Voltage vs. Output Current (Sinking) Figure 11. Figure 12. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 7 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) + V = 5V, Single Supply, TA = 25C unless otherwise specified 8 Output Short Circuit Current (Sinking) vs. Supply Voltage Leakage Current vs. Output Voltage Figure 13. Figure 14. Response Time for Overdrive (tPLH) Response Time for Overdrive (tPHL) Figure 15. Figure 16. Response Time for Overdrive (tPLH) Response Time for Overdrive (tPHL) Figure 17. Figure 18. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 Typical Performance Characteristics (continued) + V = 5V, Single Supply, TA = 25C unless otherwise specified Response Time for Overdrive (tPLH) Response Time for Overdrive (tPHL) Figure 19. Figure 20. Response Time vs. Capacitive Load Figure 21. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 9 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com LMC6772Q Supply Current vs. Supply Voltage (Output High) Supply Current vs. Supply Voltage (Output Low) 20 20 85C 18 125C 16 14 SUPPLY CURRENT (PA) (Both Comparators) SUPPLY CURRENT (PA) (Both Comparators) 18 25C -40C 12 10 8 6 4 -40C 10 8 6 Pos Input = 0.0V Neg Input = 0.1V 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) 600 Figure 22. Figure 23. Output Voltage vs. Output Current (Sinking) Output Voltage vs. Output Current (Sinking) 700 VS = 2.7V VS = 5V 600 500 125C OUTPUT VOLTAGE (mV) OUTPUT VOLTAGE (mV) 25C 12 2 0 400 85C 300 25C 200 -40C 100 125C 500 85C 400 25C 300 200 -40C 100 0 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 2 3 4 5 6 7 8 9 10 OUTPUT CURRENT (mA) Figure 24. Figure 25. Output Voltage vs. Output Current (Sinking) Output Short Circuit Current vs. Supply OUTPUT SHORT CIRCUIT CURRENT (mA) VS = 15V 600 125C 500 85C 400 300 25C 200 -40C 100 0 0 1 OUTPUT CURRENT (mA) 700 OUTPUT VOLTAGE (mV) 125C 14 4 Pos Input = 0.1V Neg Input = 0.0V 2 10 85C 16 1 2 3 4 5 6 7 8 9 10 140 120 100 80 -40C 60 25C 40 85C 20 125C 0 2 3 4 5 6 7 8 9 10 11 12 OUTPUT CURRENT (mA) SUPPLY VOLTAGE (V) Figure 26. Figure 27. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 LMC6772Q (continued) Output Leakage vs. Output Voltage 100 125C OUTPUT LEAKAGE (nA) 10 85C 0 0.1 25C 0.01 0.001 -40C (estimated) VS = 2.7V 0.0001 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OUTPUT VOLTAGE (V) Figure 28. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 11 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com APPLICATION INFORMATION INPUT COMMON-MODE VOLTAGE RANGE At supply voltages of 2.7V, 5V and 15V, the LMC6772 has an input common-mode voltage range which exceeds both supplies. As in the case of operational amplifiers, CMVR is defined by the VOS shift of the comparator over the common-mode range of the device. A CMRR (VOS/VCM) of 75 dB (typical) implies a shift of < 1 mV over the entire common-mode range of the device. The absolute maximum input voltage at V+ = 5V is 200 mV beyond either supply rail at room temperature. Figure 29. An Input Signal Exceeds the LMC6772 Power Supply Voltages with No Output Phase Inversion A wide input voltage range means that the comparator can be used to sense signals close to ground and also to the power supplies. This is an extremely useful feature in power supply monitoring circuits. An input common-mode voltage range that exceeds the supplies, 20 fA input currents (typical), and a high input impedance makes the LMC6772 ideal for sensor applications. The LMC6772 can directly interface to sensors without the use of amplifiers or bias circuits. In circuits with sensors which produce outputs in the tens to hundreds of millivolts, the LMC6772 can compare the sensor signal with an appropriately small reference voltage. This reference voltage can be close to ground or the positive supply rail. LOW VOLTAGE OPERATION Comparators are the common devices by which analog signals interface with digital circuits. The LMC6772 has been designed to operate at supply voltages of 2.7V, without sacrificing performance, to meet the demands of 3V digital systems. At supply voltages of 2.7V, the common-mode voltage range extends 200 mV (ensured) below the negative supply. This feature, in addition to the comparator being able to sense signals near the positive rail, is extremely useful in low voltage applications. Figure 30. Even at Low-Supply Voltage of 2.7V, an Input Signal which Exceeds the Supply Voltages Produces No Phase Inversion at the Output At V+ = 2.7V, propagation delays are tPLH = 4 s and tPHL = 4 s with overdrives of 100 mV. Please refer to the performance curves for more extensive characterization. 12 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 OUTPUT SHORT CIRCUIT CURRENT The LMC6772 has short circuit protection of 40 mA. However, it is not designed to withstand continuous short circuits, transient voltage or current spikes, or shorts to any voltage beyond the supplies. A resistor is series with the output should reduce the effect of shorts. For outputs which send signals off PC boards additional protection devices, such as diodes to the supply rails, and varistors may be used. HYSTERESIS If the input signal is very noisy, the comparator output might trip several times as the input signal repeatedly passes through the threshold. This problem can be addressed by making use of hysteresis as shown below. Figure 31. Canceling the Effect of Input Capacitance The capacitor added across the feedback resistor increases the switching speed and provides more short term hysteresis. This can result in greater noise immunity for the circuit. SPICE MACROMODEL A * * * Spice Macromodel is available for the LMC6772. The model includes a simulation of: Input common-mode voltage range Quiescent and dynamic supply current Input overdrive characteristics and many more characteristics as listed on the macromodel disk. A SPICE macromodel of this and many other op amps is available at no charge from the WEBENCH Design Center Team at www.ti.com Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 13 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com TYPICAL APPLICATIONS UNIVERSAL LOGIC LEVEL SHIFTER The output of the LMC6772 is the uncommitted drain of the output NMOS transistor. Many drains can be tied together to provide an output OR'ing function. An output pullup resistor can be connected to any available power supply voltage within the permitted power supply range. Figure 32. Universal Logic Level Shifter The two 1 k resistors bias the input to half of the power supply voltage. The pull-up resistor should go to the output logic supply. Due to its wide operating range, the LMC6772 is ideal for the logic level shifting applications. ONE-SHOT MULTIVIBRATOR Figure 33. One-Shot Multivibrator A monostable multivibrator has one stable state in which it can remain indefinitely. It can be triggered externally to another quasi-stable state. A monostable multivibrator can thus be used to generate a pulse of desired width. The desired pulse width is set by adjusting the values of C2 and R4. The resistor divider of R1 and R2 can be used to determine the magnitude of the input trigger pulse. The LMC6772 will change state when V1 < V2. Diode D2 provides a rapid discharge path for capacitor C2 to reset at the end of the pulse. The diode also prevents the non-inverting input from being driven below ground. BI-STABLE MULTIVIBRATOR Figure 34. Bi-Stable Multivibrator 14 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 A bi-stable multivibrator has two stable states. The reference voltage is set up by the voltage divider of R2 and R3. A pulse applied to the SET terminal will switch the output of the comparator high. The resistor divider of R1, R4, and R5 now clamps the non-inverting input to a voltage greater than the reference voltage. A pulse applied to RESET will now toggle the output low. ZERO CROSSING DETECTOR Figure 35. Zero Crossing Detector A voltage divider of R4 and R5 establishes a reference voltage V1 at the non-inverting input. By making the series resistance of R1 and R2 equal to R5, the comparator will switch when VIN = 0. Diode D1 insures that V3 never drops below -0.7V. The voltage divider of R2 and R3 then prevents V2 from going below ground. A small amount of hysteresis is setup to ensure rapid output voltage transitions. OSCILLATOR Figure 36. Square Wave Generator Figure 36 shows the application of the LMC6772 in a square wave generator circuit. The total hysteresis of the loop is set by R1, R2 and R3. R4 and R5 provide separate charge and discharge paths for the capacitor C. The charge path is set through R4 and D1. So, the pulse width t1 is determined by the RC time constant of R4 and C. Similarly, the discharge path for the capacitor is set by R5 and D2. Thus, the time t2 between the pulses can be changed by varying R5, and the pulse width can be altered by R4. The frequency of the output can be changed by varying both R4 and R5. Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 15 LMC6772 SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 www.ti.com Figure 37. Time Delay Generator The circuit shown above provides output signals at a prescribed time interval from a time reference and automatically resets the output when the input returns to ground. Consider the case of VIN = 0. The output of comparator 4 is also at ground. This implies that the outputs of comparators 1, 2, and 3 are also at ground. When an input signal is applied, the output of comparator 4 swings high and C charges exponentially through R. This is indicated above. The output voltages of comparators 1, 2, and 3 swtich to the high state when VC1 rises above the reference voltages VA, VB and VC. A small amount of hysteresis has been provided to insure fast switching when the RC time constant is chosen to give long delay times. 16 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 LMC6772 www.ti.com SNOS749F - SEPTEMBER 1995 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision E (March 2013) to Revision F * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: LMC6772 17 PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMC6772AIM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LMC67 72AIM LMC6772AIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC67 72AIM LMC6772AIMM NRND VSSOP DGK 8 1000 TBD Call TI Call TI -40 to 85 C21 LMC6772AIMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C21 LMC6772AIMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 C21 LMC6772AIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC67 72AIM LMC6772BIM NRND SOIC D 8 95 TBD Call TI Call TI -40 to 85 LMC67 72BIM LMC6772BIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC67 72BIM LMC6772BIMX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LMC67 72BIM LMC6772BIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC67 72BIM LMC6772BIN/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LMC6772 BIN LMC6772QMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AX5A LMC6772QMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 AX5A (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 27-Sep-2017 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LMC6772, LMC6772-Q1 : * Catalog: LMC6772 * Automotive: LMC6772-Q1 NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMC6772AIMM VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMC6772AIMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMC6772AIMMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMC6772AIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMC6772BIMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMC6772BIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMC6772QMM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMC6772QMMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 24-Aug-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMC6772AIMM VSSOP DGK 8 1000 210.0 185.0 35.0 LMC6772AIMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMC6772AIMMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LMC6772AIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMC6772BIMX SOIC D 8 2500 367.0 367.0 35.0 LMC6772BIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMC6772QMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMC6772QMMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMC6772AIM LMC6772AIM/NOPB LMC6772AIMM LMC6772AIMM/NOPB LMC6772AIMMX LMC6772AIMMX/NOPB LMC6772AIMX LMC6772AIMX/NOPB LMC6772BIM LMC6772BIM/NOPB LMC6772BIMX LMC6772BIMX/NOPB LMC6772BIN/NOPB