INCH-POUND MS3116E 12 September 2013 SUPERSEDING MS3116D 19 August 1976 DETAIL SPECIFICATION SHEET CONNECTORS, PLUG, ELECTRICAL, SOLDER TYPE, STRAIGHT, BAYONET COUPLING, SERIES 1, CLASSES E, F, J AND P Inactive for new design after 15 December 1998, and is no longer used, except for replacement purposes. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26482. STYLE P PIN INSERT STYLE S SOCKET INSERT FIGURE 1. Plug, classes E, F, J, and P. AMSC N/A FSC 5935 MS3116E DETAIL A DETAIL B FIGURE 1. Plug, classes E, F, J and P - Continued. 2 MS3116E A F G J Shell dia size overall .010 shoulder location .020 bay lock location + .020 / - .000 socket insert location 8 10 12 14 .782 N class 2A accessory thread UNEF .438-28 (19.86) .926 .562-24 (23.52) 1.043 .6875-24 (26.49) .353 1.183 (8.97) .337 (8.56) .8125-20 .113 (30.05) (2.87) 16 18 20 22 24 1.305 .9375-20 (33.15) 1.391 1.0625-18 (35.33) 1.531 1.1875-18 (38.89) 1.656 .415 .399 (42.06) (10.54) (10.13) 1.777 .152 (45.14) (3.86) FIGURE 1. Receptacle, classes E, F, J, and P - Continued. 3 1.3125-18 1.4375-18 MS3116E Inches mm Inches mm .005 .010 .015 .016 0.13 0.25 0.38 0.41 .020 .031 .036 .141 0.51 0.79 0.91 3.58 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 1. Plug, classes E, F, J and P - Continued. 4 MS3116E CLASS E, REAR ACCESSORY CONFIGURATION X dia min ID Y dia max OD 8 .259 (6.58) .608 (15.44) 10 .359 (9.12) .734 (18.64) .469 (11.91) .858 (21.79) 14 .589 (14.96) .984 (24.99) 16 .717 (18.21) 1.110 (28.19) 18 .779 (19.79) 1.234 (31.34) .901 (22.89) 1.360 (34.54) 1.009 (25.63) 1.484 (37.69) 1.123 (28.52) 1.610 (40.89) Shell size L max overall length 12 1.328 (33.73) 20 1.453 (36.91) 22 24 1.510 (38.35) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 2. Plug, rear accessories configurations, class E. 5 MS3116E CLASS F, WITH BUSHING CLASS F, WITH BUSHING REMOVED FIGURE 3. Plug, rear accessories configurations, class F. 6 MS3116E Shell size L max overall length Y max .828 (21.03) 8 X dia min open V max closed N (see note 4) .010 free dia 12 1.016 (25.81) .422 (10.72) .281 (7.14) .312 (7.92) 14 1.141 (28.98) .547 (13.89) .325 (8.26) .375 (9.53) 1.203 (30.56) .609 (15.47) .356 (9.04) .500 (12.70) 1.469 (37.31) .734 (18.64) 16 2.047 (51.99) 18 2.078 (52.78) 22 24 2.312 (58.72) NASM35338 - 98 or -41 .188 (4.78) .456 (11.58) 1.656 (42.06) .922 (23.42) 1.750 (44.45) .984 (24.99) .519 (13.18) .657 (16.69) NASM35333 -105 or -37 .625 (15.88) 8-32 UNC 20 2.250 (57.15) 6-32 UNC .187 (4.75) .297 (7.54) 1.906 (48.41) YZ (see note 5) lockwashers NASM35338 or NASM35333 types .125 (3.18) .234 (5.94) .891 (22.63) 10 ZZ screw threads .750 (19.05) NASM35338 -B8L or -8L -99 or -42 NASM35333 -106 or -38 .800 (20.32) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Use SAE-AS85049/139 bushing if reduced opening is required. 5. For class F: Lockwashers may be captivated. FIGURE 3. Plug, rear accessories configurations, class F - Continued. 7 MS3116E Shell size 8 10 12 14 16 18 20 22 24 L max overall length V max closed 2.271 (57.68) .187 (4.75) 2.411 (61.24) 2.599 (66.01) 2.943 (74.75) 3.172 (80.57) 3.610 (91.69) 3.766 (95.66) .281 (7.14) .325 (8.26) .356 (9.04) .456 (11.58) 3.985 (101.22) .519 (13.18) .657 (16.69) X ID gland seal min range Y dia max closed open .169 (4.29) .205 (5.21) .338 (8.59) .416 (10.57) .550 (13.97) .600 (15.24) .635 (16.13) .670 (17.02) .230 (5.84) .312 (7.92) .442 (11.23) .539 (13.69) .616 (15.65) .672 (17.07) .747 (18.97) .846 (21.49) .828 (21.03) .891 (22.63) 1.016 (25.81) 1.161 (29.49) 1.203 (30.56) .740 (18.79) .894 (22.71) 1.750 (44.45) ZZ screw threads 6-32 UNC 1.469 (37.31) 1.656 (42.06) 8-32 UNC NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. 4. Lockwashers may be captivated. FIGURE 4. Plug, rear accessories configurations, class J. 8 YZ (see note 4) Lockwashers NASM35338 or NASM35333 types NASM35338 - 98 or -41 NASM35333 -105 or -37 NASM35338 -B8L or -8L -99 or -42 NASM35333 -106 or -38 MS3116E X dia min ID Y dia max OD 8 .317 (8.05) .608 (15.44) 10 .434 (11.02) .734 (18.64) .548 (13.92) .858 (21.79) 14 .673 (17.09) .984 (24.99) 16 .798 (20.27) 1.110 (28.19) 18 .899 (22.83) 1.234 (31.34) 1.024 (26.01) 1.360 (34.54) 1.149 (29.18) 1.484 (37.69) 1.274 (32.36) 1.610 (40.89) Shell size L max overall length 12 PP min 1.500 (38.10) 20 1.609 (40.87) 22 24 1.687 (42.85) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. True position (TP) tolerances specified are in accordance with ASME-Y14.5. FIGURE 5. Plug, rear accessories configurations, class P. 9 .250 (6.35) MS3116E REQUIREMENTS: Dimensions and configurations: See figures 1 through 5. Connector mating: This connector mates with MS3110, MS3112, MS3113, MS3114 and MS3119. For insert arrangement: See MIL-STD-1669. Intermateability dimensions are in accordance with MIL-DTL-26482. Finishes: A finish designator shall not be included in the PIN when finish W is required. See MIL-DTL-26482 for other finishes, including D, T and K, available for classes E, F, P and J. Part or Identifying Number (PIN) example: MS3116 F 12 -3 P W D MS number Class Shell size Insert arrangement Contact style Alternate insert position Finish Note: When finish W is required, no finish designator is used (class W is the default finish). Restrictions: Not for Air Force use. For Air Force use, use MS3476. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26482, this document references the following: MIL-STD-1669 ASME-Y14.5 SAE-AS85049/139 10 MS3116E CONCLUDING MATERIAL Custodians: Army - CR Navy - AS Air Force - 85 DLA - CC Preparing activity: DLA - CC Review activities: Army - AV Navy - EC, SH Air Force - 99 (Project 5935-2012-225) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil. 11