TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-29
GLASS PASSIVATED UNIPOLAR DIE
ZENER VOLTAGE - 6.8 TO 200 VOLTS
.5 TO 100 WATT MAXIMUM POWER DISSIPATION
.5 TO 100 WATT UNIPOLAR
ZENER DIE
.5 TO 100 WATT ZENER
DIE SPECIFICA TIONS
♦Each Die Fully Glass Passivated: Needs No
Encapsulation
♦Each Device Individually Inspected
♦Unipolar
♦Operating Temperature: -65 to 150ºC
♦Storage Temperature: -65 to 175ºC
♦Standard Metallization Ni-Ni-Au
♦For Wire Bond Applications Gold Or Aluminum
Metallization is A vailable
♦Polarity:
6.8 to 10 Nominal Zener Volts (Vz) 1 1 to 200 Nominal Zener Volts (Vz)
A-Cathode A-Anode
B-Anode B-Cathode
CUSTOM ORDERING SPECIFIER
SZ - - -
DIE SPECIFICATIONS
UNIPOLAR
ZENER
DIE
NOMINAL ZENER
VOLTAGE %TOLERANCE OF VZ
TOLERANCES
CODE TOLERANCE
5 ±5%
10 ±10%
20 ±20% CONTACT F ACTORY FOR ELECTRICAL
SPECIFICATIONS ON CUSTOM PARTS
REFER TO PAGE 7-31
FOR A LISTING OF OUR
STANDARD PARTS
ZENER TEST
CURRENT(mA)
‘A’-SIDE METALLIZATION
CODE MATERIAL
A ALUMINUM
E GOLD
BLANK NI-NI-AU
(STANDARD)
S IZE CO DE C D E FO RWARD CURRENT S IZE CO DE C D E FO RWARD CURRENT S IZE CO DE C D E FO RWARD CURRENT
0.25 0.018 0.010 0.011 1/2 WATT 80.100 0.085 0.011 8 W A T TS 70 0.260 0.250 0.011 75 W A T TS
0.75 0.030 0.020 0.011 3/4 WATT 16 0.115 0.100 0.011 10 W A T TS 100 0.360 0.330 0.011 100 W A T TS
10.040 0.030 0.011 1 W A T T 25 0.165 0.150 0.011 25 W A T TS
1.5 0.055 0.040 0.011 3 W A T TS 30 0.180 0.166 0.011 40 W A T TS
20.070 0.055 0.011 4 W A T TS 35 0.200 0.180 0.011 50 W A T TS
30.080 0.070 0.011 5 W A T TS 40 0.220 0.205 0.011 60 W A T TS
TAB L E 1 C - UNIP OL AR DIE DIME NS ION S PE C IF ICATIONS
♦ ALL T O LE R ANCE S AR E ± .005" ♦ ALL DIMENSIONS ARE IN INCHES
7-31
NOTES
NOTE 1: ♦ ELECTRICAL CHARA CTERISTICS MEASURED AT A JUNCTION TEMPERATURE (TJ) OF 25°C UNLESS O THERWISE STATED
NOTE 2: ♦ JEDEC PART NUMBERS REFER T O PACKA GED DEVICES . THE DIES INDICATED BY THESE NUMBERS, IF PR OPERLY PA CKAGED , WILL OPERATE WITH THE SAME
PERFORMANCE
NOTE 3: ♦ VZ MEASURED AT JUNCTION AND CASE TEMPERATURE BOTH AT 25°C
NOTE 4: ♦ ZENER IMPEDANCE IS DERIVED FROM 60HZ AC VOLTAGE WHICH RESULTS WHEN AN AC CURRENT RMS VALUE EQUAL TO 10% OF D .C ZENER CURRENT IS
SUPERIMPOSED ON IZT
NOTE 5: ♦ IZM VALUES DERIVED FOR A ±5% VZ TOLERANCE
♦ IZM IS THE VALUE OF ZENER CURRENT AT WHICH POINT MAX PO WER DISSIPATION RESULTS
THIS TABLE CONTINUES
JEDEC PART
NUMBER
(NOTE 2)
SUSSEX
OR DER
CO DE
NOMINAL
ZENER
VOLTAGE
VZ @ IZT
(N OTE 3)
VOLTS
ZENE R
TEST
CURRENT
(IZT)
mA
ZENER
IMPEDANCE
ZZT @ IZT
(N OTE 4)
OHMS µA VOLTS
TYPICAL
ZENE R
V OLTAGE
TE MP.
COEFF.
%/°C
MAX. DC
ZENER
CURRENT
(IZM) @ 75°C
(N OTE 5)
mA
MAX
POWER
DISSIPATION
WATTS
1N4158A 1-6.8-5-37 6.8 37.0 3.5 500 5.2 0.040 140.0 1
1N4159A 1-7.5-5-34 7.5 34.0 4 300 5.7 0.040 125.0 1
1N4160A 1-8.2-5-31 8.2 31.0 4.5 200 6.2 0.050 115.0 1
1N4161A 1-9.1-5-28 9.1 28.0 5 100 6.9 0.060 105.0 1
1N4162A 1-10-5-25 10 25.0 7 40 7.6 0.070 95.0 1
1N4163A 1-11-5-23 11 23.0 8 10 9.1 0.070 85.0 1
1N4164A 1-12-5-21 12 21.0 9 10 9.9 0.070 80.0 1
1N4165A 1-13-5-19 13 19.0 10 10 10.6 0.070 74.0 1
1N4166A 1-15-5-17 15 17.0 14 10 11.4 0.080 63.0 1
1N4167A 1-16-5-15.5 16 15.5 16 5 12.1 0.080 60.0 1
1N4168A 1-18-5-14 18 14.0 20 5 13.7 0.080 52.0 1
1N4169A 1-20-5-12.5 20 12.5 22 5 15.2 0.080 47.0 1
1N4170A 1-22-5-11.5 22 11.5 23 5 16.7 0.090 43.0 1
1N4171A 1-24-5-10.5 24 10.5 25 5 18.2 0.090 40.0 1
1N4172A 1-27-5-9.5 27 9.5 35 1 20.5 0.090 35.0 1
1N4173A 1-30-5-8.5 30 8.5 40 1 22.8 0.090 31.0 1
1N4174A 1-33-5-7.5 33 7.5 45 1 25.1 0.095 28.0 1
1N4175A 1-36-5-7 36 7.0 50 1 27.3 0.095 26.0 1
1N4176A 1-39-5-6.5 39 6.5 60 1 30.4 0.095 24.0 1
1N4177A 1-43-5-6 43 6.0 70 1 34.2 0.095 22.0 1
1N4178A 1-47-5-5.5 47 5.5 80 1 38.0 0.095 20.0 1
1N4179A 1-51-5-5 51 5.0 95 1 42.5 0.095 17.0 1
1N4180A 1-56-5-4.5 56 4.5 110 1 45.6 0.095 15.0 1
1N4181A 1-62-5-4 62 4.0 125 1 47.1 0.095 14.5 1
1N4182A 1-68-5-3.7 68 3.7 150 1 53.2 0.095 14.0 1
1N4183A 1-75-5-3.3 75 3.3 175 1 57.0 0.095 12.0 1
1N4184A 1-82-5-3 82 3.0 200 1 60.8 0.100 11.0 1
1N4185A 1-91-5-2.8 91 2.8 250 1 68.4 0.100 10.0 1
1N4186A 1-100-5-2.5 100 2.5 350 1 76.0 0.100 9.5 1
1N4187A 1-110-5-2.3 110 2.3 450 1 83.6 0.100 8.5 1
1N4188A 1-120-5-2 120 2.0 550 1 91.2 0.100 8.0 1
1N4189A 1-130-5-1.9 130 1.9 700 1 98.8 0.100 7.2 1
1N4190A 1-150-5-1.7 150 1.7 1000 1 114.0 0.100 6.3 1
1N4191A 1-160-5-1.6 160 1.6 1100 1 121.0 0.100 5.9 1
1N4192A 1-180-5-1.4 180 1.4 1200 1 137.0 0.100 5.2 1
1N4193A 1-200-10-1.2 200 1.2 1500 1 152.0 0.100 4.7 1
T A B L E 3 C - Z EN ER DIE ELECTRIC AL SPEC IF IC ATIO N S (NO T E 1)
MAX. REVERS E
LEAKAGE
CURRENT
RE FER TO PAGE
7- 36 FOR ORD ER
SPECIFIER
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
ZENER DIE
SPECIFICATIONS
TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-32
ZENER DIE
SPECIFICATIONS CONTINUED
NOTES
NOTE 1: ♦ ELECTRICAL CHARA CTERISTICS MEASURED AT A JUNCTION TEMPERATURE (TJ) OF 25°C UNLESS O THERWISE STATED
NOTE 2: ♦ JEDEC PART NUMBERS REFER T O PACKA GED DEVICES . THE DIES INDICATED BY THESE NUMBERS, IF PR OPERLY PA CKAGED , WILL OPERATE WITH THE SAME
PERFORMANCE
NOTE 3: ♦ VZ MEASURED AT JUNCTION AND CASE TEMPERATURE BOTH AT 25°C
NOTE 4: ♦ ZENER IMPEDANCE IS DERIVED FROM 60HZ AC VOLTAGE WHICH RESULTS WHEN AN AC CURRENT RMS VALUE EQUAL TO 10% OF D .C ZENER CURRENT IS
SUPERIMPOSED ON IZT
NOTE 5: ♦ IZM VALUES DERIVED FOR A ±5% VZ TOLERANCE
♦ IZM IS THE VALUE OF ZENER CURRENT AT WHICH POINT MAX. PO WER DISSIPATION RESULTS
THIS TABLE CONTINUES
JEDEC PART
NUMBER
(NO TE 2)
SUSSEX
ORDER
CODE
NOMINAL
ZENER
VOLTAGE
VZ @ IZT
(NOTE 3)
VOLTS
ZENER
TEST
CURRENT
(IZT)
mA
ZENER
IMPEDANCE
ZZT @ IZT
(NOTE 4)
OHMS
IR
µA VDC
VOLTS
TYPICAL
ZENER
VOLTAGE
TEMP.
COEFF.
%/°C
MAX. DC
ZENER
CURRENT
(IZM) @ 75°C
(NOTE 5)
mA
MAX
POWER
DISSIP ATION
WATTS
1N5063 1.5-6.8-5-75 6.8 75.0 2 500 5.2 0.040 440.0 3
1N5064 1.5-7.5-5-75 7.5 75.0 2 300 5.7 0.040 400.0 3
1N5065 1.5-8.2-5-75 8.2 75.0 3 200 6.2 0.050 360.0 3
1N5066 1.5-9.1-5-75 9.1 75.0 3 100 6.9 0.060 330.0 3
1N5067 1.5-10-5-75 10 75.0 4 40 7.6 0.070 300.0 3
1N5068 1.5-12-5-70 11 70.0 5 10 9.1 0.070 250.0 3
1N5069 1.5-13-5-50 13 50.0 6 10 9.9 0.070 230.0 3
1N5070 1.5-14-5-50 14 50.0 6 10 10.6 0.070 210.0 3
1N5071 1.5-15-5-50 15 50.0 6 10 11.4 0.080 200.0 3
1N5072 1.5-16-5-50 16 50.0 7 5 12.1 0.080 185.0 3
1N5073 1.5-18-5-40 18 40.0 8 5 13.7 0.080 170.0 3
1N5074 1.5-22-5-30 22 30.0 10 5 16.7 0.090 135.0 3
1N5075 1.5-24-5-30 24 30.0 10 5 18.2 0.090 125.0 3
1N5076 1.5-27-5-25 27 25.0 12 1 20.5 0.090 110.0 3
1N5077 1.5-30-5-25 30 25.0 15 1 22.8 0.090 100.0 3
1N5078 1.5-33-5-20 33 20.0 21 1 25.1 0.095 90.0 3
1N5079 1.5-36-5-20 36 20.0 21 1 27.3 0.095 85.0 3
1N5080 1.5-39-5-20 39 20.0 27 1 29.5 0.095 80.0 3
1N5081 1.5-40-5-20 40 20.0 27 1 30.4 0.095 75.0 3
1N5082 1.5-43-5-15 43 15.0 35 1 32.6 0.095 70.0 3
1N5083 1.5-45-5-15 45 15.0 37 1 34.2 0.095 65.0 3
1N5084 1.5-47-5-15 47 15.0 43 1 35.7 0.095 60.0 3
1N5085 1.5-50-5-10 50 15.0 50 1 38.0 0.095 60.0 3
1N5086 1.5-51-5-15 51 15.0 50 1 38.7 0.095 55.0 3
1N5087 1.5-56-5-10 56 10.0 70 1 42.5 0.095 55.0 3
1N5088 1.5-60-5-10 60 10.0 70 1 45.6 0.095 50.0 3
1N5089 1.5-62-5-10 62 10.0 75 1 47.1 0.095 50.0 3
1N5090 1.5-68-5-10 68 10.0 85 1 51.9 0.095 45.0 3
1N5091 1.5-70-5-10 70 10.0 90 1 53.2 0.095 45.0 3
1N5092 1.5-75-5-10 75 10.0 100 1 57.0 0.095 40.0 3
1N5093 1.5-80-5-10 80 10.0 115 1 60.8 0.100 35.0 3
1N5094 1.5-82-5-10 82 10.0 120 1 68.4 0.100 30.0 3
1N5095 1.8-91-5-8 91 8.0 155 1 76.0 0.100 30.0 3
1N5096 1.5-110-5-5 110 5.0 250 1 83.6 0.100 25.0 3
1N5097 1.5-120-5-5 120 5.0 325 1 91.2 0.100 25.0 3
1N5098 1.5-130-5-5 130 5.0 375 1 98.8 0.100 20.0 3
1N5099 1.5-140-5-5 140 5.0 550 1 106.0 0.100 20.0 3
1N5100 1.5-160-5-4 160 4.0 700 1 121.0 0.100 20.0 3
1N5101 1.5-170-5-4 170 4.0 750 1 129.0 0.100 18.0 3
1N5102 1.5-180-5-4 180 4.0 850 1 137.0 0.100 18.0 3
1N5103 1.5-190-5-4 190 4.0 900 1 144.0 0.100 15.0 3
1N5104 1.5-200-5-4 200 4.0 950 1 152.0 0.100 15.0 3
T A BL E 3 C (C O NT I N UED ) - Z EN ER D I E EL ECT R I CA L SPECI FI CA T I O NS (N O T E 1 )
MAX . REVERSE
LEAKAGE CURRENT
(IR) @ VDC
REFER TO PAGE
7-36 FOR ORDER
SPECIFIER
TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-33
ZENER DIE
SPECIFICATIONS CONTINUED
NOTES
NOTE 1: ♦ ELECTRICAL CHARA CTERISTICS MEASURED AT A JUNCTION TEMPERATURE (TJ) OF 25°C UNLESS O THERWISE STATED
NOTE 2: ♦ JEDEC PART NUMBERS REFER T O PACKA GED DEVICES . THE DIES INDICATED BY THESE NUMBERS, IF PR OPERLY PA CKAGED , WILL OPERATE WITH THE SAME
PERFORMANCE
NOTE 3: ♦ VZ MEASURED AT JUNCTION AND CASE TEMPERATURE BO TH AT 25°C
NOTE 4: ♦ ZENER IMPEDANCE IS DERIVED FROM 60HZ AC VOLTA GE WHICH RESULTS WHEN AN AC CURRENT RMS VALUE EQUAL TO 10% OF D .C ZENER CURRENT IS
SUPERIMPOSED ON IZT
NOTE 5: ♦ IZM VALUES DERIVED FOR A ±5% VZ TOLERANCE
♦ IZM IS THE VALUE OF ZENER CURRENT A T WHICH POINT MAX. PO WER DISSIPATION RESUL TS
THIS TABLE CONTINUES
JEDEC PART
NUMBER
(NOTE 2)
SUSSEX
O RDER
CO DE
NOMINAL
ZENER
VOLTAGE
VZ @ IZT
(NOTE 3)
VOLTS
ZENER
TEST
CURRENT
(IZT)
mA
ZENER
IMPEDANCE
ZZT @ IZT
(NOTE 4)
OHMS
IR
µA VDC
VOLTS
TYPICAL
ZENER
VOLTAGE
TEMP.
COEFF.
%/°C
MAX. DC
ZENER
CURRENT
(IZM) @ 75° C
(N OTE 5 )
mA
MAX
POWER
DISSIPATION
WATTS
1N4954 3-6.8-5-175 6.8 175.0 1 500 5.2 0.050 670.0 5
1N4955 3-7.5-5-175 7.5 175.0 1.5 400 5.7 0.060 620.0 5
1N4956 3-8.2-5-l50 8.2 150.0 1.5 200 6.2 0.060 570.0 5
1N4957 3-9.l-5-l50 9.1 150.0 2 100 6.9 0.060 510.0 5
1N4958 3-10-5-125 10 125.0 2 75 7.6 0.070 470.0 5
1N4959 3-11-5-125 11 125.0 2.5 75 8.3 0.070 435.0 5
1N4960 3-12-5-l00 12 100.0 2.5 50 9.1 0.070 385.0 5
1N4961 3-13-5-100 13 100.0 3 25 9.9 0.080 350.0 5
1N4962 3-15-5-75 15 75.0 3.5 15 11.4 0.080 300.0 5
1N4963 3-16-5-75 16 75.0 3.5 10 12.2 0.080 275.0 5
1N4964 3-18-5-65 18 65.0 4 10 13.7 0.085 255.0 5
1N4965 3-20-5-65 20 65.0 4.5 10 15.2 0.085 220.0 5
1N4966 3-22-5-50 22 50.0 5 10 16.7 0.085 195.0 5
1N4967 3-24-5-50 24 50.0 5 10 18.2 0.090 180.0 5
1N4968 3-27-5-50 27 50.0 6 10 20.6 0.090 155.0 5
1N4969 3-30-5-40 30 40.0 8 10 22.8 0.090 140.0 5
1N4970 3-33-5-40 33 40.0 10 5 25.1 0.090 130.0 5
1N4971 3-36-5-30 36 30.0 11 5 27.4 0.095 120.0 5
1N4972 3-39-5-30 39 30.0 14 5 29.6 0.095 105.0 5
1N4973 3-43-5-30 43 30.0 20 5 32.6 0.095 95.0 5
1N4974 3-47-5-25 47 25.0 25 5 35.7 0.095 90.0 5
1N4975 3-51-5-25 51 25.0 27 5 38.0 0.095 85.0 5
1N4976 3-56-5-20 56 20.0 35 5 42.6 0.095 80.0 5
1N4977 3-62-5-20 62 20.0 42 5 47.1 0.100 75.0 5
1N4978 3-68-5-20 68 20.0 44 5 51.6 0.100 65.0 5
1N4979 3-75-5-20 75 20.0 45 5 56.0 0.100 60.0 5
1N4980 3-82-5-15 82 15.0 65 5 62.3 0.100 55.0 5
1N4981 3-91-5-15 91 15.0 75 5 68.4 0.100 50.0 5
1N4982 3-100-5-10 100 12.0 90 5 76.0 0.100 45.0 5
1N4983 3-110-5-10 110 12.0 125 5 83.6 0.100 40.0 5
1N4984 3-120-5-10 120 10.0 170 5 91.2 0.100 38.0 5
1N4985 3-130-5-10 130 10.0 190 5 98.8 0.105 35.0 5
1N4986 3-150-5-8 150 8.0 330 5 114.0 0.105 31.0 5
1N4987 3-160-5-8 160 8.0 350 5 122.0 0.105 30.0 5
1N4988 3-180-5-5 180 5.0 450 5 137.0 0.110 25.0 5
1N4989 3-200-5-5 200 5.0 500 5 152.0 0.110 22.0 5
T ABLE 3 C ( CO NTINUED) - ZENER DIE ELECTR IC AL SPECIFICAT ION S (NOTE 1)
RE FER TO PAGE
3 3 FOR ORDER
SPECIFIER
MAX. REVERSE
LEAKAGE CURRENT
(
IR
)
@ VDC
RE FER TO PAGE
7- 36 FOR ORDE R
SPECIFIER
TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-34
ZENER DIE
SPECIFICATIONS CONTINUED
NOTES
NOTE 1: ♦ ELECTRICAL CHARA CTERISTICS MEASURED AT A JUNCTION TEMPERATURE (TJ) OF 25°C UNLESS O THERWISE STATED
NOTE 2: ♦ JEDEC PART NUMBERS REFER T O PACKA GED DEVICES . THE DIES INDICATED BY THESE NUMBERS, IF PR OPERLY PA CKAGED , WILL OPERATE WITH THE SAME
PERFORMANCE
NOTE 3: ♦ VZ MEASURED AT JUNCTION AND CASE TEMPERATURE BO TH AT 25°C
NOTE 4: ♦ ZENER IMPEDANCE IS DERIVED FROM 60HZ AC VOLTA GE WHICH RESULTS WHEN AN AC CURRENT RMS VALUE EQUAL TO 10% OF D .C ZENER CURRENT IS
SUPERIMPOSED ON IZT
NOTE 5: ♦ IZM VALUES DERIVED FOR A ±5% VZ TOLERANCE
♦ IZM IS THE VALUE OF ZENER CURRENT AT WHICH POINT DIE POWER DISSIPATION RESULTS
THIS TABLE CONTINUES
JEDEC PART
NUMBER
(N O TE 2 )
SUSSEX
ORDER
CODE
NOM INA L
ZENER
VOLTAGE
VZ @ I
ZT
(NO TE 3)
VOLTS
ZENER
TEST
C U RRENT
(IZT)
mA
ZENER
IM P EDAN CE
ZZT @ I
ZT
(NO TE 4)
OHMS IR
µA VDC
VOLTS
TYPICA L
ZENER
V OLTAGE
TEMP.
C O EFF.
%/°C
MAX. DC
ZEN ER
C U RRENT
(IZM) @ 75°C
(NO TE 5)
mA
MAX
POWE R
DISSIPATION
WATTS
1N2970B 16-6.8-5-370 6.8 370 1.2 150 5.2 .040 1320 10
1N2971B 16-7.5-5-335 7.5 335 1.3 100 5.7 .045 1180 10
1N2972B 16-8.2-5-305 8.2 305 1.5 50 6.2 .048 1040 10
1N2973B 16-9.1-5-275 9.1 275 2.0 25 6.9 .051 960 10
1N2974B 16-10-5-250 10.0 250 3.0 25 7.6 .055 860 10
1N2975B 16-11-5-230 11.0 230 3.0 10 8.4 .060 780 10
1N2976B 16-12-5-210 12.0 210 3.0 10 9.1 .065 720 10
1N2977B 16-13-5-190 13.0 190 3.0 10 9.9 .065 660 10
1N2978B 16-14-5-180 14.0 180 3.0 10 10.5 .070 600 10
1N2979B 16-15-5-170 15.0 170 3.0 10 11.4 .070 560 10
1N2980B 16-16-5-155 16.0 155 4.0 10 12.2 .070 530 10
1N2981B 16-17-5-145 17.0 145 4.0 10 13.0 .075 500 10
1N2982B 16-18-5-140 18.0 140 4.0 10 13.7 .075 460 10
1N2983B 16-19-5-130 19.0 130 4.0 10 14.0 .075 440 10
1N2984B 16-20-5-125 20.0 125 4.0 10 15.2 .075 420 10
1N2985B 16-22-5-115 22.0 115 5.0 10 16.7 .080 380 10
1N2986B 16-24-5-105 24.0 105 5.0 10 18.2 .080 350 10
1N2987B 16-25-5-100 25.0 100 6.0 10 18.2 .080 310 10
1N2988B 16-27-5-95 27.0 95 7.0 10 20.6 .085 300 10
1N2989B 16-30-5-85 30.0 85 8.0 10 22.8 .085 280 10
1N2990B 16-33-5-75 33.0 75 9.0 10 25.1 .085 260 10
1N2991B 16-36-5-70 36.0 70 10.0 10 27.4 .085 230 10
1N2992B 16-39-5-65 39.0 65 11.0 10 29.7 .090 210 10
1N2993B 16-43-5-60 43.0 60 12.0 10 32.7 .090 195 10
1N2994B 16-45-5-55 45.0 55 13.0 10 33.0 .090 185 10
1N2995B 16-47-5-55 47.0 55 14.0 10 35.8 .090 175 10
1N2996B 16-50-5-50 50.0 50 15.0 10 36.0 .090 165 10
1N2997B 16-51-5-50 51.0 50 15.0 10 38.8 .090 160 10
1N2998B 16-52-5-50 52.0 50 15.0 10 39.0 .090 160 10
1N2999B 16-56-5-45 56.0 45 16.0 10 42.6 .090 150 10
1N3000B 16-62-5-40 62.0 40 17.0 10 47.1 .090 130 10
1N3001B 16-68-5-37 68.0 37 18.0 10 51.7 .090 120 10
1N3002B 16-75-5-33 75.0 33 22.0 10 56.0 .090 110 10
1N3003B 16-82-5-30 82.0 30 25 10 62.2 .090 100 10
1N3004B 16-91-5-28 91.0 28 35 10 69.2 .090 85 10
1N3005B 16-100-5-25 100.0 25 40 10 76.0 .090 80 10
1N3006B 16-105-5-25 105.0 25 45 10 76.0 .095 75 10
1N3007B 16-110-5-23 110.0 23 55 10 83.6 .095 72 10
1N3008B 16-120-5-20 120.0 20 75 10 91.2 .095 67 10
1N3009B 16-130-5-19 130.0 19 100 10 98.8 .095 62 10
1N3010B 16-140-5-18 140.0 18 125 10 100.0 .095 58 10
1N3011B 16-150-5-17 150.0 17 175 10 114.0 .095 54 10
1N3012B 16-160-5-16 160.0 16 200 10 121.6 .095 50 10
1N3013B 16-175-5-14 175.0 14 250 10 135.0 .095 46 10
1N3014B 16-180-5-14 180.0 14 260 10 136.8 .095 45 10
1N3015B 16-200-5-12 200.0 12 300 10 152.0 .100 40 10
TABLE 3C (CO NTINUED) - ZENER DIE ELECTRICAL SPECIFICATIO NS (NO TE 1)
REFER TO PAGE
23 FOR ORDER
S PE CIF IE R
REFER TO PAGE
33 FOR ORDER
S PE CIF IE R
M AX . REV ERSE
LEA KAGE CURRENT
(IR) @ VDC
REFER TO PAGE
7-36 F OR ORDER
S PE CIF IE R
TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-35
ZENER DIE
SPECIFICATIONS CONTINUED
NOTES
NOTE 1: ♦ ELECTRICAL CHARA CTERISTICS MEASURED AT A JUNCTION TEMPERATURE (TJ) OF 25°C UNLESS O THERWISE STATED
NOTE 2: ♦ JEDEC PART NUMBERS REFER T O PACKA GED DEVICES . THE DIES INDICATED BY THESE NUMBERS, IF PR OPERLY PA CKAGED , WILL OPERATE WITH THE SAME
PERFORMANCE
NOTE 3: ♦ VZ MEASURED AT JUNCTION AND CASE TEMPERATURE BOTH AT 25°C
NOTE 4: ♦ ZENER IMPEDANCE IS DERIVED FROM 60HZ AC VOLTAGE WHICH RESULTS WHEN AN AC CURRENT RMS VALUE EQUAL TO 10% OF D .C ZENER CURRENT IS
SUPERIMPOSED ON IZT
NOTE 5: ♦ IZM VALUES DERIVED FOR A ±5% VZ TOLERANCE
♦ IZM IS THE VALUE OF ZENER CURRENT AT WHICH POINT DIE PO WER DISSIPATION RESULTS
JEDEC
PART
NUMBER
(N O TE 2)
SUSSEX
ORDER
CODE
NOM INA L
ZENER
VOLTAGE
VZ @ I
ZT
(NO TE 3)
VOLTS
Z ENER TES T
CURRENT
(IZT)
mA
Z ENER
IM P ED AN CE
ZZT @ I
ZT
(NO TE 4)
OHM S IR
µA VDC
VOLTS
TYPICAL
ZENER
VOLTAGE
TEM P.
COEFF.
%/°C
MAX. DC
ZENER
CURRENT
(IZM) @ 75 °C
( NOT E 5 )
mA
M A X POW ER
DISSIPAT ION
WATTS
1N3305B 35-6.8-5-1850 6.8 1850 0.2 150 4.5 .040 6600 50
1N3306B 35-7.5-5-1700 7.5 1700 0.3 100 5.0 .045 5900 50
1N3307B 35-8.2-5-1500 8.2 1500 0.4 50 5.4 .048 5200 50
1N3308B 35-9.1-5-1370 9.1 1370 0.5 25 6.1 .050 4800 50
1N3309B 35-10-5-1200 10.0 1200 0.6 25 6.7 .055 4300 50
1N3310B 35-11-5-1100 11.0 1100 0.8 10 8.4 .060 3900 50
1N3311B 35-12-5-1000 12.0 1000 1.0 10 9.1 .065 3800 50
1N3312B 35-13-5-960 13.0 960 1.1 10 9.9 .065 3300 50
1N3313B 35-14-5-890 14.0 890 1.2 10 11.4 .070 3000 50
1N3314B 35-15-5-830 15.0 830 1.4 10 11.4 .070 2800 50
1N3315B 35-16-5-780 16.0 780 1.6 10 12.2 .070 2650 50
1N3316B 35-17-5-740 17.0 740 1.8 10 13.0 .075 2500 50
1N3317B 35-18-5-700 18.0 700 2.0 10 13.7 .075 2300 50
1N3318B 35-19-5-660 19.0 660 2.2 10 13.7 .075 2200 50
1N3319B 35-20-5-630 20.0 630 2.4 10 15.2 .075 2100 50
1N3320B 35-22-5-570 22.0 570 2.5 10 16.7 .080 1900 50
1N3321B 35-24-5-520 24.0 520 2.6 10 18.2 .080 1750 50
1N3322B 35-25-5-500 25.0 500 2.7 10 18.2 .080 1550 50
1N3323B 35-27-5-460 27.0 460 2.8 10 20.6 .085 1500 50
1N3324B 35-30-5-420 30.0 420 3.0 10 22.8 .085 1400 50
1N3325B 35-33-5-380 33.0 380 3.2 10 25.1 .085 1300 50
1N3326B 35-36-5-350 36.0 350 3.5 10 27.4 .085 1150 50
1N3327B 35-39-5-320 39.0 320 4.0 10 29.7 .090 1050 50
1N3328B 35-43-5-290 43.0 290 4.5 10 32.7 .090 975 50
1N3329B 35-45-5-280 45.0 280 4.5 10 32.7 .090 930 50
1N3330B 35-47-5-270 47.0 270 5.0 10 35.8 .090 880 50
1N3331B 35-50-5-250 50.0 250 5.0 10 38.0 .090 830 50
1N3332B 35-51-5-245 51.0 245 5.2 10 38.8 .090 810 50
1N3333B 35-52-5-240 52.0 240 5.5 10 42.6 .090 790 50
1N3334B 35-56-5-220 56.0 220 6.0 10 42.6 .090 740 50
1N3335B 35-62-5-200 62.0 200 7.0 10 47.1 .090 660 50
1N3336B 35-68-5-180 68.0 180 8.0 10 51.7 .090 600 50
1N3337B 35-75-5-170 75.0 170 9.0 10 56.0 .090 540 50
1N3338B 35-82-5-150 82.0 150 11 10 62.2 .090 490 50
1N3339B 35-91-5-140 91.0 140 15 10 69.2 .090 420 50
1N3340B 35-100-5-120 100.0 120 20 10 76.0 .090 400 50
1N3341B 35-105-5-120 105.0 120 25 10 83.0 .095 380 50
1N3342B 35-110-5-110 110.0 110 30 10 83.0 .095 365 50
1N3343B 35-120-5-100 120.0 100 40 10 91.2 .095 335 50
1N3344B 35-130-5-95 130.0 95 50 10 99.8 .095 310 50
1N3345B 35-140-5-90 140.0 90 60 10 114.0 .095 290 50
1N3346B 35-150-5-85 150.0 85 75 10 114.0 .095 270 50
1N3347B 35-160-5-80 160.0 80 80 10 121.6 .095 250 50
1N3348B 35-175-5-70 175.0 70 85 10 121.6 .095 230 50
1N3349B 35-180-5-68 180.0 68 90 10 136.8 .095 220 50
1N3350B 35-200-5-65 200.0 65 100 10 152.0 .100 200 50
TABLE 3C (CO NTINUED) - ZENER DIE ELECTRICAL SPECIFICATIO NS (NOTE 1)
REFER TO PAGE
23 FOR ORDER
S PE CIF IER
REFER TO PAGE
33 FOR ORDER
S PE CIF IER
M AX . REVERS E
LEAKAGE CURRENT
(IR) @ VDC
RE FE R TO PAGE 7 -36
FOR ORDE R
SPECIFIER
TM
12251 TOWNE LAKE DRIVE, FORT MYERS, FLORIDA, 33913 TEL: (941) 768-6800 FAX: (941) 768-6868
SUSSEX
SEMICONDUCTOR, INC.
7-36
ZENER DIE
SPECIFICATIONS CONTINUED
ORDERING SPECIFIER
0
25
50
75
100
0 25 50 75 100 125 150 175 200
% RATED PO WER DISSIPATION
JUNCTION TEMPERA TURE ,TJ (°C) ZENER CURRENT (mA)
ZENER IMPEDANCE (Ohms)
FIGURE 1C - STEADY-STATE
DERATING CURVE
6.8 - 10 - 75
ORDER CODE FROM
PREVIOUS PAGE
10-1
100
101
102
103
104
100101102103104
35-6.8-5-1850
16-10-5-250
35-75-5-170
16-75-5-33
35-200-5-65
16-200-5-12
FIGURE 2C - ZENER IMPEDANCE VS.
ZENER CURRENT
SZ STANDARD UNIPOLAR DIE
SZFD FLIP-DIE (1/2 TO 10 WA TT ONLY)
CODE DESCRIPTION
CODE DIE TYPE DIE SPECIF ICAT IONS
REFER T O: CODE DIE TYPE DIE SPECIF ICAT IONS
REFER T O:
0.25 1/2 W ATT UNIPOLAR DIE PAGE 7-29 AND 7- 30 16 16 WAT T UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
0.75 3/4 W ATT UNIPOLAR DIE PAGE 7-29 AND 7- 30 25 25 WAT T UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
1 1 WAT T UNIPOL AR DI E PAG E 7-29 AND 7- 3 0 30 40 WATT UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
1.5 3 WAT T UNIPOLAR DIE PAG E 7-2 9 AND 7- 3 0 35 50 WATT UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
2 4 WAT T UNIPOL AR DI E PAG E 7-29 AND 7- 3 0 40 60 WATT UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
3 5 WAT T UNIPOL AR DI E PAG E 7-29 AND 7- 3 0 70 75 WATT UNIPOLAR DIE PAGE 7-2 9 AND 7-3 0
8 8 WAT T UNIPOL AR DI E PAG E 7-29 AND 7- 3 0 10 0 10 0 WAT T UNIPOL AR DIE PAG E 7-29 AND 7- 3 0
TABLE 4C - AVAILABLE DIE SIZES
