1
dc1565afa
DEMO MANUAL DC1565A
Description
LTC2153-14, LTC2153-12,
LTC2152-14, LTC2152-12,
LTC2151-14, LTC2151-12,
LTC2150-14, LTC2150-12
12-Bit/14-Bit, 170Msps to 310Msps ADCs
Demonstration circuit 1565A supports a family of
12‑Bit/14‑Bit 170Msps to 310Msps ADCs. Each assem‑
bly features one of the following devices: LTC2153‑14/
LTC2153‑12, LTC2152‑14/LTC2152‑12, LTC2151‑14/
LTC2151‑12, LTC2150‑14/LTC2150‑12, high speed ADCs.
The versions of the 1565A demo board are listed in Table1.
Depending on the required resolution and sample rate,
the DC1565A is supplied with the appropriate ADC. The
L, LT, LTC, LTM, µModule, Linear Technology and the Linear logo are registered trademarks
and PScope is a trademark of Linear Technology Corporation. All other trademarks are the
property of their respective owners.
circuitry on the analog inputs is optimized for analog input
frequencies from 5MHz to 140MHz. Refer to the data sheet
for proper input networks for different input frequencies.
Design files for this circuit board are available at
http://www.linear.com/demo
Table 1. DC1565A Variants
DC1565A VARIANTS ADC PART NUMBER RESOLUTION MAXIMUM SAMPLE RATE INPUT FREQUENCY
1565A‑A LTC2152‑14 14‑Bit 250Msps 5MHz to 140MHz
1565A‑B LTC2151‑14 14‑Bit 210Msps 5MHz to 140MHz
1565A‑C LTC2150‑14 14‑Bit 170Msps 5MHz to 140MHz
1565A‑D LTC2152‑12 12‑Bit 250Msps 5MHz to 140MHz
1565A‑E LTC2151‑12 12‑Bit 210Msps 5MHz to 140MHz
1565A‑F LTC2150‑12 12‑Bit 170Msps 5MHz to 140MHz
1565A‑G LTC2153‑14 14‑Bit 310Msps 5MHz to 140MHz
1565A‑H LTC2153‑12 12‑Bit 310Msps 5MHz to 140MHz
perForMAnce sUMMArY
(TA = 25°C)
PARAMETER CONDITIONS MIN TYP MAX UNITS
Supply Voltage – DC1565A Depending on Sampling Rate and the A/D Converter
Provided, This Supply Must Provide Up to 500mA.
3 3.6 6 V
Analog Input Range Depending on SENSE Pin Voltage 1.5 or 1.32 VP‑P
Logic Input Voltages Minimum Logic High
Maximum Logic Low
1.3
0.6
V
V
Logic Output Voltages (Differential) Nominal Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
Minimum Logic Levels (100Ω Load, 3.5mA Mode)
Common Mode
350
1.25
247
1.25
mV
V
mV
V
Sampling Frequency (Convert Clock Frequency) See Table 1
Encode Clock Level Differential Encode Mode (ENC– Not Tied to GND) 0.2 1.9 V
Resolution See Table 1
2
dc1565afa
DEMO MANUAL DC1565A
TO PROVIDED
USB CABLE
TO PROVIDED
POWER SUPPLY
CHANNEL 1
PARALLEL/SERIAL
SINGLE-ENDED ENCODE CLOCK
(USE A LOW JITTER SIGNAL GENERATOR
WITH PROPER FILTERING)
dc1565a F01
3.6V TO 6V
qUick stArt proceDUre
Figure 1. DC1565 Setup
Demonstration circuit 1565A is easy to set up to evaluate
the performance of the LTC2152 A/D converter family. Refer
to Figure 1 for proper measurement equipment setup and
follow the procedure below:
Setup
If a DC1371 Data Acquisition and Collection System was
supplied with the DC1565A demonstration circuit, fol‑
low the DC1371 Quick Start Guide to install the required
software and for connecting the DC1371 to the DC1565A
and to a PC.
DC1565A Demonstration Circuit Board Jumpers
The DC1565A demonstration circuit board should have
the following jumper settings as default positions: (as
per Figure 1)
JP2 PAR/SER: Selects parallel or serial programming
mode. (default ‑ serial)
perForMAnce sUMMArY
(TA = 25°C)
Input Frequency Range See Table 1
SFDR See Applicable Data Sheet
SNR See Applicable Data Sheet
3
dc1565afa
DEMO MANUAL DC1565A
qUick stArt proceDUre
Applying Power and Signals to the DC1565A
Demonstration Circuit
The DC1371 is used to acquire data from the DC1565A,
the DC1371 must first be connected to a powered USB
port and have 5V applied power before applying 3.6V to
6V across the pins marked V+ and GND on the DC1565A.
DC1565A requires 3.6V for proper operation.
Regulators on the board produce the voltages required for
the ADC. The DC1565A demonstration circuit requires up
to 500mA depending on the sampling rate and the A/D
converter supplied.
The DC1565A should not be removed, or connected to
the DC1371 while power is applied.
Analog Input Network
For optimal distortion and noise performance the RC
network on the analog inputs may need to be optimized
for different analog input frequencies. For input frequen‑
cies above 140MHz, refer to the LTC2152 data sheet for a
proper input network. Other input networks may be more
appropriate for input frequencies less that 5MHz.
In almost all cases, filters will be required on both analog
input and encode clock to provide data sheet SNR.
The filters should be located close to the inputs to avoid
reflections from impedance discontinuities at the driven
end of a long transmission line. Most filters do not present
50Ω outside the passband. In some cases, 3dB to 10dB
pads may be required to obtain low distortion.
If your generator cannot deliver full‑scale signals without
distortion, you may benefit from a medium power amplifier
based on a Gallium Arsenide Gain block prior to the final
filter. This is particularly true at higher frequencies where
IC based operational amplifiers may be unable to deliver
the combination of low noise figure and High IP3 point
required. A high order filter can be used prior to this final
amplifier, and a relatively lower Q filter used between the
amplifier and the demo circuit.
Apply the analog input signal of interest to the SMA
connector on the DC1565A demonstration circuit board
marked J4 AINA. This input is capacitively coupled to a
balun transformer ETC1‑1‑13 (lead free part number:
MABA007159‑000000).
Encode Clock
NOTE: Apply an encode clock to the SMA connector on
the DC1565A demonstration circuit board marked CLK+.
As a default the DC1565A is populated to have a single‑
ended input.
For the best noise performance, the encode input must
be driven with a very low jitter, sine wave source. The
amplitude should be large, up to 3VP‑P or 13dBm.
Using bandpass filters on the clock and the analog input will
improve the noise performance by reducing the wideband
noise power of the signals. Data sheet FFT plots are taken
with 10‑pole LC filters made by TTE (Los Angeles, CA) to
suppress signal generator harmonics, non‑harmonically
related spurs and broadband noise. Low phase noise
Agilent 8644B generators are used for both the clock input
and the analog input.
Digital Outputs
The data outputs, data clock, and frame clock signals are
available on J1 of the DC1565A. This connector follows the
VITA‑57/FMC standard, but all signals should be verified
when using an FMC carrier card other than the DC1371.
Software
The DC1371 is controlled by the PScope™ System Soft‑
ware provided or downloaded from the Linear Technology
website at http://www.linear.com/software/.
To start the data collection software if PScope.exe, is in‑
stalled (by default) in \Program Files\LTC\PScope\, double
click the PScope icon or bring up the run window under
the start menu and browse to the PScope directory and
select PScope.
If the DC1565A demonstration circuit is properly connected
to the DC1371, PScope should automatically detect the
DC1565A, and configure itself accordingly.
If everything is hooked up properly, powered and a suit‑
able convert clock is present, clicking the Collect button
should result in time and frequency plots displayed in
the PScope window. Additional information and help for
PScope is available in the DC1371 Quick Start Guide and in
the online help available within the PScope program itself.
4
dc1565afa
DEMO MANUAL DC1565A
qUick stArt proceDUre
Figure 3. Demobd Configuration Options
Figure 2. PScope Toolbar
Serial Programming
PScope has the ability to program the DC1565A board
serially through the DC1371. There are several options
available in the LTC2152 family that are only available
through serially programming. PScope allows all of these
features to be tested.
These options are available by first clicking on the Set
Demo Bd Options icon on the PScope toolbar (Figure 2).
This will bring up the menu shown in Figure 3.
This menu allows any of the options available for the
LTC2152 family to be programmed serially. The LTC2152
family has the following options:
Sleep Mode: Selects between normal operation, sleep
mode.
• Off(Default):EntireADCispowered,andactive
• On:TheentireADCispowereddown
NAP: Selects between normal operation and nap mode.
• Off(Default):Channeloneisactive
• On:Channeloneisinnapmode
Clock Inversion: Selects the polarity of the CLKOUT signal:
• Normal(Default):NormalCLKOUTpolarity
• Inverted:CLKOUTpolarityisinverted
ClkOut Phase: Selects the phase delay of the CLKOUT
signal:
• None(Default):NoCLKOUTdelay
• 45deg:CLKOUTdelayedby45degrees
• 90deg:CLKOUTdelayedby90degrees
• 135deg:CLKOUTdelayedby135degrees
Clock Duty Cycle: Enable or disables duty cycle stabilizer
• Stabilizeroff(Default):Dutycyclestabilizerdisabled
• Stabilizeron:Dutycyclestabilizerenabled
5
dc1565afa
DEMO MANUAL DC1565A
qUick stArt proceDUre
Output Current: Selects the LVDS output drive current
• 1.75mA(Default):LVDSoutputdrivercurrent
• 2.1mA:LVDSoutputdrivercurrent
• 2.5mA:LVDSoutputdrivercurrent
• 3.0mA:LVDSoutputdrivercurrent
• 3.5mA:LVDSoutputdrivercurrent
• 4.0mA:LVDSoutputdrivercurrent
• 4.5mA:LVDSoutputdrivercurrent
Internal Termination: Enables LVDS internal termination
• Off(Default):Disablesinternaltermination
• On:Enablesinternaltermination
Outputs: Enables digital outputs
• Enabled(Default):Enablesdigitaloutputs
• Disabled:Disablesdigitaloutputs
Test Pattern: Selects digital output test patterns
• Allout=0(default):Alldigitaloutputsare0
• Allout=1:Alldigitaloutputsare1
• Checkerboard:OF,andD13-D0Alternatebetween101
0101 1010 0101 and 010 1010 0101 1010 on alternat‑
ing samples.
• Alternating:Digitaloutputsalternatebetweenall1’sand
all0’sonalternatingsamples
Alternate Bit: Alternate bit polarity mode
• Off(Default):Disablesalternatebitpolarity
• On:Enablesalternatebitpolarity(BeforeenablingABP,
be sure the part is in offset binary mode)
TP Enable: Selects digital output test patterns. The desired
test pattern can be entered into the text boxes provided.
• Off(default):ADCinputdataisdisplayed
• On:Testpatternisdisplayed.
Randomizer: Enables data output randomizer
• Off(Default):Disablesdataoutputrandomizer
• On:Enablesdataoutputrandomizer
Two’s Complement:Enablestwo’scomplementmode
• Off(Default):Selectsoffsetbinarymode
• On:Selectstwo’scomplementmode
Once the desired settings are selected hit OK and PScope
will automatically update the register of the device on the
DC1565A demo board.
6
dc1565afa
DEMO MANUAL DC1565A
pArts list
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 4 C1, C3, C8, C10 Capacitor, X7R, 1µF, 10V, 10%, 0603 AVX, 0603ZC105KAT2A
2 2 C2, C9 Capacitor, X5R, 0.1µF, 10V, 10%, 0603 AVX, 0603ZD104KAQ2A
3 2 C4, C11 Capacitor, X7R, 47µF, 10V, 10%, 1210 Murata, GRM32ER71A476KE15L
4 8 C5, C6, C12, C16, C21, C23, Capacitor, X5R, 0.1µF, 10V, 10%, 0402 AVX, 0402ZD104KAQ2A
C34, C35
5 1 C7 Capacitor, X5R, 4.7µF, 6.3V, 20%, 0603 AVX, 06036D475MAT2A
6 1 C13 Capacitor, X5R, 2.2µF, 10V, 20%, 0603 AVX, 0603ZD225MAT2A
7 2 C14, C19 Capacitor, X7R, 0.01µF, 50V, 10%, 0603 AVX, 06035C103KAQ2A
8 3 C15, C26, C27 Capacitor, C0G, 4.7pF, 50V, 5%, 0402 AVX, 04025A4R7JAT2A
9 2 C17, C18 Capacitor, C0G, 8.2pF, 50V, 5%, 0402 AVX, 04025A8R2JAT2A
10 5 C20, C24, C28, C29, C36 Capacitor, X7R, 0.01µF, 16V, 10%, 0402 Murata, GRM155R71C103KA01D
11 1 C22 Capacitor, X5R, 2.2µF, 10V, 20%, 0603 AVX, 0603ZD225MAT2A
12 0 R15, C25 OPT 0402
13 4 C30, C31, C32, C33 Capacitor, C0G, 47pF, 16V, 10%, 0402 AVX, 0402YA470KA
14 1 D1 Diode Schottky, RF SER, 15V, SOT‑23 Avago, HSMS‑2822‑TR1G
15 1 JP1 Header, 2‑Pin 0.079 Single Row Samtec, TMM‑102‑02‑L‑S
16 1 J1 BGA Connector, 40 × 10 Samtec, SEAM‑40‑02.0‑S‑10‑2‑A‑K‑TR
17 2 J2, J3 Connector, SMA, 50Ω, Straight Mount Connex., 132134
18 1 J4 Connector, SMA, 50Ω, EDGE‑LANCH E. F. Johnson, 142‑0701‑851
19 1 L1 Inductor, 56nH, 0603 Murata, LQP18MN56NG02D
20 0 L2 OPT 0603
21 3 L3, L4, L5 Ferrite Bead, 1206 Murata, BLM31PG330SN1L
22 0 L6 Bead, OPT 1206
23 22 R1, R2, R3, R4, R5, R6, R7, R8, R10,
R16, R20, R21, R23, R24, R25, R27,
R28, R33, R34, R35, R36, R47
Resistor, Chip, 100, 1/16W, 5%, 0402 NIC, NRC04J101TRF
24 5 R9, R37, R38, R39, R40 Resistor, Chip, 1k, 1/16W, 5%, 0402 Yageo, RC0402FR‑071KL
25 2 R11, R18 Resistor, Chip, 33.2Ω, 1/16W, 1%, 0402 NIC, NRC04F33R2TRF
26 1 R12 Resistor, Chip, 86.6Ω, 1/16W, 1%, 0402 NIC, NRC04F86R6TRF
27 2 R13, R17 Resistor, Chip, 86.6Ω, 1/16W, 1%, 0603 Vishay, CRCW060386R6FNEA
28 2 R14, R19 Resistor, Chip, 10Ω, 1/16W, 5%, 0402 Vishay, CRCW040210R0JNED
7
dc1565afa
DEMO MANUAL DC1565A
pArts list
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
29 2 R26, R32 Resistor, Chip, 5.1Ω, 1/16W, 1%, 0402 Vishay, CRCW04025R10FKED
30 1 R29 PES., Chip, 0Ω, 0402 Vishay, CRCW04020000Z0ED
31 2 R30, R31 Resistor, Chip, 49.9Ω, 1/16W, 1%, 0402 Yageo, RC0402FR‑0749R9L
32 3 R41, R42, R43 Resistor, Chip, 5.1k, 1/16W, 1%, 0402 NIC, NRC04F5101TRF
33 3 TP1, TP2, TP3 Testpoint, Turret, 0.094" pbf Mill‑Max, 2501‑2‑00‑80‑00‑00‑07‑0
34 2 T1, T3 Transformer, MABA‑007159‑000000 M/A‑COM, MABA‑007159‑000000
35 1 T2 Transformer, WBC1‑1L Coilcraft, WBC1‑1L
36 1 U1 IC, LTC2152CUJ, 40‑Pin QFN 6mm × 6mm Linear Technology, LTC2152CUJ#PBF
37 1 U3 IC, LT1763CS8‑1.8, SO8 Linear Technology, LT1763CS8‑1.8#TRPBF
38 1 U4 IC, LT1763CS8‑3‑3, SO8 Linear Technology, LT1763CS8‑3.3#TRPBF
39 1 U5 IC, EEPROM, 32k, 400khz, 8TSSOP MICROChip, 24LC32A‑I/ST
40 1 Fab, Printed Circuit Board Demo Circuit 1565A
41 2 Top & Botton Stencil for Proto Stencil 1565A
8
dc1565afa
DEMO MANUAL DC1565A
scheMAtic DiAgrAM
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
AINA
SENSE



CLK+
V+
3V - 6V
GND
CLK-
PAR_SER
aina-
aina+
sense
of+
of-
gnd
sense
VDD
VDD
OVDD
OVDD
VDD
VDD OVDD
VDD
DA4_5+
DA10_11+
DA8_9+
DA2_3+
DA12_13+
DA6_7+
CLKOUT+
CS
SCK
SDI
SDO
DA0_1-
DA10_11-
DA12_13-
DA0_1+
DA6_7-
CLKOUT-
DA4_5-
DA2_3-
DA8_9-


 
 




TECHNOLOGY





























 
 




TECHNOLOGY





























 
 




TECHNOLOGY




























  

 


  

 


  

 

R18
54
R18
54
R34
OPT
R34
OPT
L4
BEAD
L4
BEAD
C13
2.2uF
0603
C13
2.2uF
0603
R28
100
R28
100
R14
5
R14
5
C16
0.1uF
C16
0.1uF
R10
5
R10
5
C34
0.1uF
C34
0.1uF
J2J2
R17
86.6
0603
R17
86.6
0603
L6
OPT
L6
OPT
JP2JP2 1
3
2
C9
0.1uF
C9
0.1uF
R26
5.1
R26
5.1
R45
0
R45
0
R24
OPT
R24
OPT
C24
0.01uF
C24
0.01uF
R19
5
R19
5
C12
0.1uF
C12
0.1uF
R32
5.1
R32
5.1
R25
OPT
R25
OPT
C29
0.01uF
C29
0.01uF
C5
0.1uF
C5
0.1uF
J4J4
R22
1K
R22
1K
L1
56nH
0603
L1
56nH
0603
C21
0.1uF
C21
0.1uF
R9
1K
R9
1K
R23
OPT
R23
OPT
C10
1uF
C10
1uF
T3
MABA-007159-000000
T3
MABA-007159-000000
5
4 3
1
2
R27
OPT
R27
OPT
R35
OPT
R35
OPT
U3
LT1763CS8-1.8
U3
LT1763CS8-1.8

1

2

3

4

5

6

7

8
C20
0.01uF
C20
0.01uF
R36
OPT
R36
OPT
C17
8.2pF
C17
8.2pF
T1
MABA-007159-000000
T1
MABA-007159-000000
5
4 3
1
2
C35
0.1uF
C35
0.1uF
TP1TP1
R11
54
R11
54
R13
86.6
0603
R13
86.6
0603
C7
4.7uF
C7
4.7uF
TP3TP3
C18
8.2pF
C18
8.2pF
T2
WBC1-1L
T2
WBC1-1L
4
6
3
1
2
TP2TP2
R15
OPT
R15
OPT
+ C11
47uF
1210
+ C11
47uF
1210
R16
100
R16
100
R31
49.9
R31
49.9
R20
5
R20
5
R47
100
R47
100
C6
0.1uF
C6
0.1uF
R21
50
R21
50
C22
2.2uF
C22
2.2uF
C15
4.7pF
C15
4.7pF
C36
0.01uF
C36
0.01uF
R44
0
R44
0
U1
LTC2152UJ
U1
LTC2152UJ

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

29

24

25

26

27

28

22

23

31

32

33

34

35

36

37

38

39

40

30

41
R12 86.6
R12 86.6
R33
OPT
R33
OPT
C8
1uF
C8
1uF
R30
49.9
R30
49.9
R29 0R29 0
C19
0.01uF
0603
C19
0.01uF
0603
C14
0.01uF
0603
C14
0.01uF
0603
J3J3
C23
OPT
C23
OPT
L5
BEAD
L5
BEAD
C28
0.01uF
C28
0.01uF
9
dc1565afa
DEMO MANUAL DC1565A
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa‑
tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.
scheMAtic DiAgrAM
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
CHANNEL 0
CHANNEL 1
WP
+3.3V
VDD
DA10_11+
DA10_11-
DA6_7-
DA6_7+
DA2_3-
DA2_3+
DA12_13-
DA12_13+
DA4_5+
DA4_5-
DA0_1+
DA0_1-
DA8_9-
DA8_9+
CLKOUT+
CLKOUT-
SDO
CS
SCK
SDI


 
 




TECHNOLOGY





























 
 




TECHNOLOGY





























 
 




TECHNOLOGY



























C31
47pF
C31
47pF
J1J
SEAM-10X40PIN
J1J
SEAM-10X40PIN

J1

J2

J3

J4

J5

J6

J7

J8

J9

J10

J11

J12

J13

J14

J15

J16

J17

J18

J19

J20

J21

J22

J23

J24

J25

J26

J27

J28

J29

J30

J31

J32

J33

J34

J35

J36

J37

J38

J39

J40
R41
5K
R41
5K
J1E
SEAM-10X40PIN
J1E
SEAM-10X40PIN

E1

E2

E3

E4

E5

E6

E7

E8

E9

E10

E11

E12

E13

E14

E15

E16

E17

E18

E19

E20

E21

E22

E23

E24

E25

E26

E27

E28

E29

E30

E31

E32

E33

E34

E35

E36

E37

E38

E39

E40
J1A
SEAM-10X40PIN
J1A
SEAM-10X40PIN

A1

A2

A3

A4

A5

A6

A7

A8

A9

A10

A11

A12

A13

A14

A15

A16

A17

A18

A19

A20

A21

A22

A23

A24

A25

A26

A27

A28

A29

A30

A31

A32

A33

A34

A35

A36

A37

A38

A39

A40
C32
47pF
C32
47pF
C33
47pF
C33
47pF
J1K
SEAM-10X40PIN
J1K
SEAM-10X40PIN

K1

K2

K3

K4

K5

K6

K7

K8

K9

K10

K11

K12

K13

K14

K15

K16

K17

K18

K19

K20

K21

K22

K23

K24

K25

K26

K27

K28

K29

K30

K31

K32

K33

K34

K35

K36

K37

K38

K39

K40
R46
100K
R46
100K
J1F
SEAM-10X40PIN
J1F
SEAM-10X40PIN

F1

F2

F3

F4

F5

F6

F7

F8

F9

F10

F11

F12

F13

F14

F15

F16

F17

F18

F19

F20

F21

F22

F23

F24

F25

F26

F27

F28

F29

F30

F31

F32

F33

F34

F35

F36

F37

F38

F39

F40
J1B
SEAM-10X40PIN
J1B
SEAM-10X40PIN

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40
C30
47pF
C30
47pF
J1G
SEAM-10X40PIN
J1G
SEAM-10X40PIN

G1

G2

G3

G4

G5

G6

G7

G8

G9

G10

G11

G12

G13

G14

G15

G16

G17

G18

G19

G20

G21

G22

G23

G24

G25

G26

G27

G28

G29

G30

G31

G32

G33

G34

G35

G36

G37

G38

G39

G40
R38
1K
R38
1K
R42
5K
R42
5K
J1C
SEAM-10X40PIN
J1C
SEAM-10X40PIN

C1

C2

C3

C4

C5

C6

C7

C8

C9

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

C29

C30

C31

C32

C33

C34

C35

C36

C37

C38

C39

C40
R37
1K
R37
1K
R39
1K
R39
1K
R40
1K
R40
1K
JP1JP1
1
2
J1H
SEAM-10X40PIN
J1H
SEAM-10X40PIN

H1

H2

H3

H4

H5

H6

H7

H8

H9

H10

H11

H12

H13

H14

H15

H16

H17

H18

H19

H20

H21

H22

H23

H24

H25

H26

H27

H28

H29

H30

H31

H32

H33

H34

H35

H36

H37

H38

H39

H40
R43
5K
R43
5K
J1D
SEAM-10X40PIN
J1D
SEAM-10X40PIN

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

D15

D16

D17

D18

D19

D20

D21

D22

D23

D24

D25

D26

D27

D28

D29

D30

D31

D32

D33

D34

D35

D36

D37

D38

D39

D40
U5
24LC32A-I /ST
U5
24LC32A-I /ST

1

2

3

4

5

6

7

8
10
dc1565afa
DEMO MANUAL DC1565A
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035‑7417
(408) 432‑1900 ● FAX: (408) 434‑0507 ● www.linear.com
LINEAR TECHNOLOGY CORPORATION 2011
LT 1211 REV A • PRINTED IN USA
DEMONSTRATION BOARD IMPORTANT NOTICE
Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:
This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT
OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete
in terms of required design‑, marketing‑, and/or manufacturing‑related protective considerations, including but not limited to product safety
measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union
directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.
If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date
of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims
arisingfromthehandlingoruseofthegoods.Duetotheopenconstructionoftheproduct,itistheuser’sresponsibilitytotakeanyandall
appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or
agency certified (FCC, UL, CE, etc.).
No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.
LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.
Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and
observe good laboratory practice standards. Common sense is encouraged.
This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica‑
tion engineer.
Mailing Address:
Linear Technology
1630 McCarthy Blvd.
Milpitas, CA 95035
Copyright © 2004, Linear Technology Corporation