LTC4075/LTC4075X Dual Input USB/AC Adapter Standalone Li-Ion Battery Chargers U FEATURES DESCRIPTIO The LTC(R)4075/LTC4075X are standalone linear chargers that are capable of charging a single-cell Li-Ion battery from both wall adapter and USB inputs. The chargers can detect power at the inputs and automatically select the appropriate power source for charging. Charges Single-Cell Li-Ion Batteries from Wall Adapter and USB Inputs Automatic Input Power Detection and Selection Charge Current Programmable up to 950mA from Wall Adapter Input No External MOSFET, Sense Resistor or Blocking Diode Needed Thermal Regulation Maximizes Charging Rate Without Risk of Overheating* Preset Charge Voltage with 0.6% Accuracy Programmable Charge Current Termination 18A USB Suspend Current in Shutdown Independent "Power Present" Status Outputs Charge Status Output Automatic Recharge Available Without Trickle Charge (LTC4075X) Available in a Thermally Enhanced, Low Profile (0.75mm) 10-Lead (3mm x 3mm) DFN Package U APPLICATIO S No external sense resistor or blocking diode is required for charging due to the internal MOSFET architecture. Internal thermal feedback regulates the battery charge current to maintain a constant die temperature during high power operation or high ambient temperature conditions. The float voltage is fixed at 4.2V and the charge current is programmed with an external resistor. The LTC4075 terminates the charge cycle when the charge current drops below the programmed termination threshold after the final float voltage is reached. With power applied to both inputs, the LTC4075/LTC4075X can be put into shutdown mode reducing the DCIN supply current to 20A, the USBIN supply current to 10A, and the battery drain current to less than 2A. Other features include automatic recharge, undervoltage lockout, charge status outputs, and "power present" status outputs to indicate the presence of wall adapter or USB power. Cellular Telephones Handheld Computers Portable MP3 Players Digital Cameras , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. *Protected by U.S. patents, including 6522118, 6700364 U Complete Charge Cycle (1100mAh Battery) USB PORT 1F 800mA (WALL) 500mA (USB) LTC4075 WALL ADAPTER BAT DCIN USBIN 1F + IUSB 2k IDC 1% 1.24k 1% ITERM GND 4.2V SINGLE CELL Li-Ion BATTERY 2k 1% 4075 TA01 BATTERY CHARGE VOLTAGE (V) CURRENT (mA) Dual Input Battery Charger for Single-Cell Li-Ion 1000 800 600 400 200 0 4.2 4.0 3.8 3.6 3.4 DCIN VOLTAGE (V) TYPICAL APPLICATIO 5.0 CONSTANT VOLTAGE USBIN = 5V TA = 25C RIDC = 1.25k RIUSB = 2k 2.5 0 -2.5 0 0.5 1.0 2.0 1.5 TIME (HR) 2.5 3.0 4075 TA01b 4075Xfa 1 LTC4075/LTC4075X U W W W ABSOLUTE AXI U RATI GS U W U PACKAGE/ORDER I FOR ATIO (Note 1) Input Supply Voltage (DCIN, USBIN) ........... -0.3 to 10V ENABLE, CHRG, PWR, USBPWR ................. -0.3 to 10V BAT, IDC, IUSB, ITERM .................................. -0.3 to 7V DCIN Pin Current (Note 7) ..........................................1A USBIN Pin Current (Note 7) .................................700mA BAT Pin Current (Note 7) ............................................1A BAT Short-Circuit Duration............................Continuous Maximum Junction Temperature .......................... 125C Operating Temperature Range (Note 2) .. -40C to 85C Storage Temperature Range.................. -65C to 125C TOP VIEW 10 DCIN USBIN 1 IUSB 2 ITERM 3 PWR 4 7 USBPWR CHRG 5 6 ENABLE 9 BAT 8 IDC 11 DD PACKAGE 10-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 40C/W (NOTE 3) EXPOSED PAD IS GND (PIN 11) MUST BE SOLDERED TO PCB ORDER PART NUMBER DD PART MARKING LTC4075EDD LTC4075XEDD LBSC LBRK Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VDCIN = 5V, VUSBIN = 5V unless otherwise noted. SYMBOL PARAMETER VDCIN VUSBIN IDCIN Supply Voltage Supply Voltage DCIN Supply Current IUSBIN CONDITIONS MIN TYP MAX UNITS V V A A A Charge Mode (Note 4), RIDC = 10k Standby Mode; Charge Terminated Shutdown Mode (ENABLE = 5V) 250 50 20 8 8 800 100 40 USBIN Supply Current Charge Mode (Note 5), RIUSB = 10k, VDCIN = 0V Standby Mode; Charge Terminated, VDCIN = 0V Shutdown (VDCIN = 0V, ENABLE = 0V) VDCIN > VUSBIN 250 50 18 10 800 100 36 20 A A A A VFLOAT Regulated Output (Float) Voltage IBAT = 1mA IBAT = 1mA, 0C < TA < 85C IBAT BAT Pin Current VIDC VIUSB ITERMINATE IDC Pin Regulated Voltage IUSB Pin Regulated Voltage Charge Current Termination Threshold RIDC = 1.25k, Constant-Current Mode RIUSB = 2.1k, Constant-Current Mode RIDC = 10k or RIUSB = 10k Standby Mode, Charge Terminated Shutdown Mode (Charger Disabled) Sleep Mode (VDCIN = 0V, VUSBIN = 0V) Constant-Current Mode Constant-Current Mode RITERM = 1k RITERM = 2k RITERM = 10k RITERM = 20k 4.2 4.2 800 476 100 -3 -1 1 1 1 100 50 10 5 4.225 4.242 840 500 107 -6 -2 2 1.05 1.05 110 55 11.5 6 V V mA mA mA A A A V V mA mA mA mA 4.3 4.3 4.175 4.158 760 450 93 0.95 0.95 90 45 8.5 4 4075Xfa 2 LTC4075/LTC4075X ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VDCIN = 5V, VUSBIN = 5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS ITRIKL Trickle Charge Current (Note 6) VBAT < VTRIKL; RIDC = 1.25k VBAT < VTRIKL; RIUSB = 2.1k VTRIKL Trickle Charge Threshold (Note 6) VBAT Rising Hysteresis 60 30 2.8 80 47.5 2.9 100 100 65 3 mA mA V mV VUVDC DCIN Undervoltage Lockout Voltage From Low to High Hysteresis 4 4.15 200 4.3 V mV VUVUSB USBIN Undervoltage Lockout Voltage From Low to High Hysteresis 3.8 3.95 200 4.1 V mV VASD-DC VDCIN - VBAT Lockout Threshold VDCIN from Low to High, VBAT = 4.2V VDCIN from High to Low, VBAT = 4.2V VASD-USB VUSBIN - VBAT Lockout Threshold VUSBIN from Low to High, VBAT = 4.2V VUSBIN from High to Low, VBAT = 4.2V VENABLE RENABLE VCHRG VPWR VUSBPWR VRECHRG tRECHRG tTERMINATE tSS RON-DC ENABLE Input Threshold Voltage ENABLE Pulldown Resistance CHRG Output Low Voltage PWR Output Low Voltage USBPWR Output Low Voltage Recharge Battery Threshold Recharge Comparator Filter Time Termination Comparator Filter Time Soft-Start Time Power FET "ON" Resistance (Between DCIN and BAT) 140 20 140 20 0.4 1.2 180 50 180 50 0.7 2 0.35 0.35 0.35 100 6 1.5 250 400 220 80 220 80 1 5 0.6 0.6 0.6 135 9 2.2 325 mV mV mV mV V M V V V mV ms ms s m RON-USB Power FET "ON" Resistance (Between USBIN and BAT) 550 m TLIM Junction Temperature in Constant-Temperature Mode 105 C ICHRG = 5mA IPWR = 5mA IUSBPWR = 300A VFLOAT - VRECHRG, 0C < TA < 85C VBAT from High to Low IBAT Drops Below Termination Threshold IBAT = 10% to 90% Full-Scale Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC4075E/LTC4075XE are guaranteed to meet the performance specifications from 0C to 70C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Failure to correctly solder the exposed backside of the package to the PC board will result in a thermal resistance much higher than 40C/W. See Thermal Considerations. 65 3 0.8 175 Note 4: Supply current includes IDC and ITERM pin current (approximately 100A each) but does not include any current delivered to the battery through the BAT pin. Note 5: Supply current includes IUSB and ITERM pin current (approximately 100A each) but does not include any current delivered to the battery through the BAT pin. Note 6: This parameter is not applicable to the LTC4075X. Note 7: Guaranteed by long term current density limitations. 4075Xfa 3 LTC4075/LTC4075X U W TYPICAL PERFOR A CE CHARACTERISTICS Regulated Output (Float) Voltage vs Charge Current 4.220 VDCIN = VUSBIN = 5V 1.008 VDCIN = VUSBIN = 5V 1.006 4.22 4.210 1.004 4.20 4.205 1.002 4.18 VIDC (V) 4.215 4.16 4.200 0.998 4.14 4.190 0.996 4.12 4.185 0.994 RIDC = 1.25k 100 200 300 400 500 600 700 800 CHARGE CURRENT (mA) 0 4.180 -50 -25 75 0 25 50 TEMPERATURE (C) IUSB Pin Voltage vs Temperature (Constant-Current Mode) 0.992 -50 1.008 900 1.006 800 1.004 700 900 VDCIN = 5V VUSBIN = 4.3V 0.998 600 RIDC = 2k 500 400 -25 0 25 50 TEMPERATURE (C) 75 0 0 0.4 0.2 0.6 0.8 VIDC (V) 4075X G04 1.2 1.0 0 5 TA = 25C IUSBPWR (mA) ICHRG (mA) 15 TA = 90C 20 15 10 10 5 5 0 1 2 4 3 VPWR (V) 5 6 7 4075X G07 4 TA = 90C 3 2 1 0 0 TA = - 40C TA = 25C 25 TA = 90C VDCIN = 5V VUSBIN = 0V TA = -40C 30 TA = 25C 20 6 VDCIN = VUSBIN = 5V TA = -40C 1.2 1.0 USBPWR Pin I-V Curve 35 35 25 0.6 0.8 VIUSB (V) 4075X G06 CHRG Pin I-V Curve VDCIN = VUSBIN = 5V 0.4 0.2 4075X G05 PWR Pin I-V Curve 30 RIUSB = 10k 100 0 100 400 200 RIDC = 10k 100 0.992 -50 RIUSB = 2k 500 300 200 0.994 RIUSB = 1.25k 700 300 0.996 100 VUSBIN = 5V 800 RIDC = 1.25k IBAT (mA) IBAT (mA) 1.000 75 0 25 50 TEMPERATURE (C) Charge Current vs IUSB Pin Voltage 600 VUSBIN = 8V -25 4075X G03 Charge Current vs IDC Pin Voltage 1.002 VDCIN = 4.3V 4075X G02 4075X G01 VIUSB (V) 100 VDCIN = 8V 1.000 4.195 RIDC = RIUSB = 2k 4.10 IPWR (mA) IDC Pin Voltage vs Temperature (Constant-Current Mode) 4.24 VFLOAT (V) VFLOAT (V) 4.26 Regulated Output (Float) Voltage vs Temperature 0 1 2 4 3 VCHRG (V) 5 6 7 4075X G08 0 0 1 2 4 3 5 VUSBPWR (V) 6 7 4075X G09 4075Xfa 4 LTC4075/LTC4075X U W TYPICAL PERFOR A CE CHARACTERISTICS Charge Current vs Ambient Temperature Charge Current vs Supply Voltage 1000 900 ONSET OF THERMAL REGULATION Charge Current vs Battery Voltage 1000 ONSET OF THERMAL REGULATION LTC4075X 800 800 800 RIDC = 1.25k RIDC = RIUSB = 2k 400 IBAT (mA) IBAT (mA) IBAT (mA) 700 600 600 600 400 500 200 VDCIN = VUSBIN = 5V VBAT = 4V JA = 40C/W 0 -50 -25 400 50 25 75 0 TEMPERATURE (C) 100 300 4.0 4.5 125 200 RIDC = 1.25k VBAT = 4V JA = 35C/W 0 7.5 7.0 5.5 6.0 6.5 VDCIN (V) 5.0 2.4 8.0 2.7 3.0 3.3 3.6 VBAT (V) 3.9 4.2 DCIN Power FET "On" Resistance vs Temperature USBIN Power "On" Resistance vs Temperature 800 VBAT = 4V IBAT = 200mA 750 4.5 4075X G12 4075X G11 4075X G10 550 VDCIN = VUSBIN = 5V JA = 40C/W RIDC = 1.25k LTC4075 ENABLE Pin Threshold (On-to-Off) vs Temperature 900 VBAT = 4V IBAT = 200mA VDCIN = VUSBIN = 5V 500 850 400 350 650 VENABLE (mV) 450 RDS(ON) (m) RDS(ON) (m) 700 600 550 500 800 750 700 450 300 650 400 250 -50 -25 50 25 75 0 TEMPERATURE (C) 100 350 -50 -25 125 50 25 75 0 TEMPERATURE (C) 100 4075X G13 45 45 40 15 10 0 -50 ENABLE Pin Pulldown Resistance vs Temperature 2.6 VUSBIN = 8V RENABLE (M) VDCIN = 5V 25 20 VUSBIN = 5V 15 VDCIN = 4.3V 5 10 ENABLE = 5V -25 100 2.8 30 IUSBIN (A) IDCIN (A) 20 75 35 VDCIN = 8V 30 25 50 25 0 TEMPERATURE (C) 4075X G15 USBIN Shutdown Current vs Temperature 50 35 -25 4075X G14 DCIN Shutdown Current vs Temperature 40 600 -50 125 50 25 0 TEMPERATURE (C) 75 100 4075X G16 VUSBIN = 4.3V 5 0 -50 2.4 2.2 2.0 1.8 ENABLE = 0V -25 50 25 0 TEMPERATURE (C) 75 100 4075X G17 1.6 -50 -25 50 25 0 TEMPERATURE (C) 75 100 4075X G18 4075Xfa 5 LTC4075/LTC4075X U W TYPICAL PERFOR A CE CHARACTERISTICS Undervoltage Lockout Threshold vs Temperature Recharge Threshold vs Temperature 4.16 4.30 4.25 4.14 DCIN UVLO 4.20 4.12 VRECHRG (V) VUV (V) 4.15 4.10 4.05 VDCIN = VUSBIN = 4.3V 4.10 VDCIN = VUSBIN = 8V 4.08 USBIN UVLO 4.00 4.06 3.95 3.90 -50 -25 0 25 50 TEMPERATURE (C) 75 100 4.04 -50 -25 0 25 50 TEMPERATURE (C) 100 4075X G20 4075X G19 Battery Drain Current vs Temperature 5 75 Charge Current During Turn-On and Turn-Off VBAT = 4.2V VDCIN, VUSBIN (NOT CONNECTED) 4 IBAT 500mA/DIV IBAT (A) 3 2 ENABLE 5V/DIV 1 0 -1 -50 -25 0 25 50 TEMPERATURE (C) 75 100 4075X G21 VDCIN = 5V RIDC = 1.25k 100s/DIV 4075X G22 4075Xfa 6 LTC4075/LTC4075X U U U PI FU CTIO S USBIN (Pin 1): USB Input Supply Pin. Provides power to the battery charger. The maximum supply current is 650mA. This pin should be bypassed with a 1F capacitor. IUSB (Pin 2): Charge Current Program for USB Power. The charge current is set by connecting a resistor, RIUSB, to ground. When charging in constant-current mode, this pin servos to 1V. The voltage on this pin can be used to measure the battery current delivered from the USB input using the following formula: IBAT = VIUSB *1000 RIUSB ITERM (Pin 3): Termination Current Threshold Program. The termination current threshold, ITERMINATE, is set by connecting a resistor, RITERM, to ground. ITERMINATE is set by the following formula: ITERMINATE = 100V RITERM When the battery current, IBAT, falls below the termination threshold, charging stops and the CHRG output becomes high impedance. This pin is internally clamped to approximately 1.5V. Driving this pin to voltages beyond the clamp voltage can draw large currents and should be avoided. PWR (Pin 4): Open-Drain Power Supply Status Output. When the DCIN or USBIN pin voltage is sufficient to begin charging (i.e. when the supply is greater than the undervoltage lockout threshold and at least 180mV above the battery terminal), the PWR pin is pulled low by an internal N-channel MOSFET. Otherwise PWR is high impedance. This output is capable of sinking up to 10mA, making it suitable for driving an LED. CHRG (Pin 5): Open-Drain Charge Status Output. When the LTC4075 is charging, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge cycle is completed, CHRG becomes high impedance. This output is capable of sinking up to 10mA, making it suitable for driving an LED. ENABLE (Pin 6): Enable Input. When the LTC4075 is charging from the DCIN source, a logic low on this pin enables the charger. When the LTC4075 is charging from the USBIN source, a logic high on this pin enables the charger. If this input is left floating, an internal 2M pulldown resistor defaults the LTC4075 to charge when a wall adapter is applied and to shut down if only the USB source is applied. USBPWR (Pin 7): Open-Drain USB Power Status Output. When the voltage on the USBIN pin is sufficient to begin charging and there is insufficient power at DCIN, the USBPWR pin is high impedance. In all other cases, this pin is pulled low by an internal N-channel MOSFET, provided that there is power present at the DCIN, USBIN, or BAT inputs. This output is capable of sinking up to 1mA, making it suitable for driving high impedance logic inputs. IDC (Pin 8): Charge Current Program for Wall Adapter Power. The charge current is set by connecting a resistor, RIDC, to ground. When charging in constant-current mode, this pin servos to 1V. The voltage on this pin can be used to measure the battery current delivered from the DC input using the following formula: IBAT = VIDC *1000 RIDC BAT (Pin 9): Charger Output and Regulator Input. This pin provides charge current to the battery and regulates the final float voltage to 4.2V. DCIN (Pin 10): Wall Adapter Input Supply Pin. Provides power to the battery charger. The maximum supply current is 950mA. This should be bypassed with a 1F capacitor. Exposed Pad (Pin 11): GND. The exposed backside of the package is ground and must be soldered to PC board ground for electrical connection and maximum heat transfer. 4075Xfa 7 LTC4075/LTC4075X W BLOCK DIAGRA DCIN BAT USBIN 10 9 1 CC/CV REGULATOR USBPWR 7 + 1mA MAX 4 5 DC SOFT-START USB SOFT-START DCIN UVLO 10mA MAX BAT CHRG + - 4.15V PWR CC/CV REGULATOR 10mA MAX + - 3.95V USBIN UVLO + + - - BAT 4.1V RECHARGE LOGIC - RECHRG BAT TRICKLE DC_ENABLE - ENABLE *TRICKLE CHARGE USB_ENABLE + TDIE - 105C CHARGER CONTROL + TERM 2.9V + 100mV THERMAL REGULATION 6 RENABLE IBAT/1000 TERMINATION IBAT/1000 IBAT/1000 - ITERM GND 3 11 IDC 8 IUSB 2 4075 BD *TRICKLE CHARGE DISABLED ON THE LTC4075X RITERM RIDC RIUSB 4075Xfa 8 LTC4075/LTC4075X U OPERATIO The LTC4075 is designed to efficiently manage charging of a single-cell lithium-ion battery from two separate power sources: a wall adapter and USB power bus. Using the constant-current/constant-voltage algorithm, the charger can deliver up to 950mA of charge current from the wall adapter supply or up to 650mA of charge current from the USB supply with a final float voltage accuracy of 0.6%. The LTC4075 has two internal P-channel power MOSFETs and thermal regulation circuitry. No blocking diodes or external sense resistors are required. Programming and Monitoring Charge Current The charge current delivered to the battery from the wall adapter supply is programmed using a single resistor from the IDC pin to ground. Likewise, the charge current from the USB supply is programmed using a single resistor from the IUSB pin to ground. The program resistor and the charge current (ICHRG) are calculated using the following equations: Power Source Selection The LTC4075 can charge a battery from either the wall adapter input or the USB port input. The LTC4075 automatically senses the presence of voltage at each input. If both power sources are present, the LTC4075 defaults to the wall adapter source provided sufficient power is present at the DCIN input. "Sufficient power" is defined as: RIUSB * Supply voltage is greater than the battery voltage by 50mV (180mV rising, 50mV falling). IBAT VUSBIN > 3.95V and VUSBIN > BAT + 50mV VDCIN > 4.15V and VDCIN > BAT + 50mV VDCIN < 4.15V or VDCIN < BAT + 50mV Device powered from wall adapter source; USBIN current < 25A PWR: LOW USBPWR: LOW Device powered from USB source; PWR: LOW USBPWR: Hi-Z VUSBIN < 3.95V or VUSBIN < BAT + 50mV Device powered from wall adapter source PWR: LOW USBPWR: LOW No charging , ICHRG-DC = VIDC * 1000, (ch arg ing fromwall adapter) RIDC V = IUSB * 1000, (ch arg ing fromUSB sup ply) RIUSB IBAT = Table 1. Power Source Selection 1000V Charge current out of the BAT pin can be determined at any time by monitoring the IDC or IUSB pin voltage and using the following equations: * Supply voltage is greater than the UVLO threshold. The open drain power status outputs (PWR and USBPWR) indicate which power source has been selected. Table 1 describes the behavior of these status outputs. 1000V ICHRG-DC RIDC 1000V 1000V = , ICHRG-USB = ICHRG-USB RIUSB RIDC = Programming Charge Termination The charge cycle terminates when the charge current falls below the programmed termination threshold during constant-voltage mode. This threshold is set by connecting an external resistor, RITERM, from the ITERM pin to ground. The charge termination current threshold (ITERMINATE) is set by the following equation: RITERM = 100V ITERMINATE , ITERMINATE = 100V RITERM PWR: Hi-Z USBPWR: LOW 4075Xfa 9 LTC4075/LTC4075X U OPERATIO The termination condition is detected by using an internal filtered comparator to monitor the ITERM pin. When the ITERM pin voltage drops below 100mV* for longer than tTERMINATE (typically 1.5ms), charging is terminated. The charge current is latched off and the LTC4075 enters standby mode. When charging, transient loads on the BAT pin can cause the ITERM pin to fall below 100mV for short periods of time before the DC charge current has dropped below the programmed termination current. The 1.5ms filter time (tTERMINATE) on the termination comparator ensures that transient loads of this nature do not result in premature charge cycle termination. Once the average charge current drops below the programmed termination threshold, the LTC4075 terminates the charge cycle and ceases to provide any current out of the BAT pin. In this state, any load on the BAT pin must be supplied by the battery. Low Battery Charge Conditioning (Trickle Charge) This feature ensures that near-dead batteries are gradually charged before reapplying full charge current . If the BAT pin voltage is below 2.9V, the LTC4075 supplies 1/10th of the full charge current to the battery until the BAT pin rises back above 2.9V. For example, if the charger is programmed to charge at 800mA from the wall adapter input and 500mA from the USB input, the charge current during trickle charge mode would be 80mA and 50mA, respectively. The LTC4075X does not include the trickle charge feature; it outputs full charge current to the battery when the BAT pin voltage is below 2.9V. The LTC4075X is useful in applications where the trickle charge current may be insufficient to supply the load during low battery voltage conditions. Automatic Recharge In standby mode, the charger sits idle and monitors the battery voltage using a comparator with a 6ms filter time (tRECHRG). A charge cycle automatically restarts when the battery voltage falls below 4.1V (which corresponds to approximately 80%-90% battery capacity). This ensures that the battery is kept at, or near, a fully charged condi*Any external sources that hold the ITERM pin above 100mV will prevent the LTC4075 from terminating a charge cycle. tion and eliminates the need for periodic charge cycle initiations. If the battery is removed from the charger, a sawtooth waveform of approximately 100mV appears at the battery output. This is caused by the repeated cycling between termination and recharge events. This cycling results in pulsing at the CHRG output; an LED connected to this pin will exhibit a blinking pattern, indicating to the user that a battery is not present. The frequency of the sawtooth is dependent on the amount of output capacitance. Manual Shutdown The ENABLE pin has a 2M pulldown resistor to GND. The definition of this pin depends on which source is supplying power. When the wall adapter input is supplying power, logic low enables the charger and logic high disables it (the pulldown defaults the charger to the charging state). The opposite is true when the USB input is supplying power; logic low disables the charger and logic high enables it (the default is the shutdown state). The DCIN input draws 20A when the charger is in shutdown. The USBIN input draws 18A during shutdown if no power is applied to DCIN, but draws only 10A when VDCIN > VUSBIN. Charge Current Soft-Start and Soft-Stop The LTC4075 includes a soft-start circuit to minimize the inrush current at the start of a charge cycle. When a charge cycle is initiated, the charge current ramps from zero to full-scale current over a period of 250s. Likewise, internal circuitry slowly ramps the charge current from full-scale to zero in a period of approximately 30s when the charger shuts down or self terminates. This minimizes the transient current load on the power supply during start-up and shut-off. Status Indicators H R G ) has two states: pull-down The charge status output (C and high impedance. The pull-down state indicates that the LTC4075 is in a charge cycle. Once the charge cycle has terminated or the LTC4075 is disabled, the pin state becomes high impedance. The pull-down state is capable of sinking up to 10mA. 4075Xfa 10 LTC4075/LTC4075X U OPERATIO W R ) has two states: pullThe power supply status output (P down and high impedance. The pull-down state indicates that power is present at either DCIN or USBIN. This output is strong enough to drive an LED. If no power is applied at either pin, the PWR pin is high impedance, indicating that the LTC4075 lacks sufficient power to charge the battery. The pull-down state is capable of sinking up to 10mA. The USB power status output (USBPWR) has two states: pull-down and high impedance. The high impedance state indicates that the LTC4075 is being powered from the USBIN input. The pull-down state indicates that the charger is either powered from DCIN or is in a UVLO condition (see Table 1). The pull-down state is capable of sinking up to 1mA. Thermal Limiting An internal thermal feedback loop reduces the programmed charge current if the die temperature attempts to rise above a preset value of approximately 105C. This feature protects the LTC4075 from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the device. The charge current can be set according to typical (not worst-case) ambient temperature with the assurance that the charger will automatically reduce the current in worstcase conditions. DFN power considerations are discussed further in the Applications Information section. STARTUP DCIN POWER APPLIED ONLY USB POWER APPLIED POWER SELECTION DCIN POWER REMOVED BAT < 2.9V TRICKLE CHARGE MODE* USBIN POWER REMOVED OR DCIN POWER APPLIED TRICKLE CHARGE MODE* 1/10th FULL CURRENT CHRG STATE: PULLDOWN CHRG STATE: PULLDOWN BAT > 2.9V 2.9V < BAT BAT > 2.9V CHARGE MODE CHARGE MODE FULL CURRENT FULL CURRENT CHRG STATE: PULLDOWN CHRG STATE: PULLDOWN ENABLE DRIVEN LOW STANDBY MODE STANDBY MODE NO CHARGE CURRENT NO CHARGE CURRENT CHRG STATE: Hi-Z CHRG STATE: Hi-Z ENABLE DRIVEN HIGH SHUTDOWN MODE ENABLE DRIVEN LOW IDCIN DROPS TO 20A CHRG STATE: Hi-Z *LTC4075 ONLY 2.9V < BAT IBAT < ITERMINATE IN VOLTAGE MODE IBAT < ITERMINATE IN VOLTAGE MODE BAT < 4.1V BAT < 2.9V 1/10th FULL CURRENT SHUTDOWN MODE BAT < 4.1V ENABLE DRIVEN HIGH IUSBIN DROPS TO 18A DCIN POWER REMOVED USBIN POWER REMOVED OR DCIN POWER APPLIED CHRG STATE: Hi-Z 4075 F01 Figure 1. LTC4075 State Diagram of a Charge Cycle 4075Xfa 11 LTC4075/LTC4075X U U W U APPLICATIO S I FOR ATIO Using a Single Charge Current Program Resistor The LTC4075 can program the wall adapter charge current and USB charge current independently using two program resistors, RIDC and RIUSB. Figure 2 shows a charger circuit that sets the wall adapter charge current to 800mA and the USB charge current to 500mA. 800mA (WALL) 500mA (USB) LTC4075 WALL ADAPTER BAT DCIN USB PORT USBIN 1F 1F RIUSB 2k 1% + IUSB RIDC 1.24k 1% IDC ITERM GND RITERM 1k 1% 4075 F02 Figure 2. Full Featured Dual Input Charger Circuit In applications where the programmed wall adapter charge current and USB charge current are the same, a single program resistor can be used to set both charge currents. Figure 3 shows a charger circuit that uses one charge current program resistor. LTC4075 WALL ADAPTER USB PORT DCIN 500mA BAT USBIN 1F 1F + IUSB RISET 2k 1% IDC ITERM GND RITERM 1k 1% 4075 F03 Figure 3. Dual Input Charger Circuit. The Wall Adapter Charge Current and USB Charge Current are Both Programmed to be 500mA In this circuit, the programmed charge current from both the wall adapter supply is the same value as the programmed charge current from the USB supply: ICHRG- DC = ICHRG-USB = 1000V RISET Stability Considerations The constant-voltage mode feedback loop is stable without any compensation provided a battery is connected to the charger output. However, a 1F capacitor with a 1 series resistor is recommended at the BAT pin to keep the ripple voltage low when the battery is disconnected. When the charger is in constant-current mode, the charge current program pin (IDC or IUSB) is in the feedback loop, not the battery. The constant-current mode stability is affected by the impedance at the charge current program pin. With no additional capacitance on this pin, the charger is stable with program resistor values as high as 20k (ICHRG = 50mA); however, additional capacitance on these nodes reduces the maximum allowed program resistor. Power Dissipation When designing the battery charger circuit, it is not necessary to design for worst-case power dissipation scenarios because the LTC4075 automatically reduces the charge current during high power conditions. The conditions that cause the LTC4075 to reduce charge current through thermal feedback can be approximated by considering the power dissipated in the IC. Most of the power dissipation is generated from the internal charger MOSFET. Thus, the power dissipation is calculated to be: PD = (VIN - VBAT) * IBAT 4075Xfa 12 LTC4075/LTC4075X U W U U APPLICATIO S I FOR ATIO PD is the power dissipated, VIN is the input supply voltage (either DCIN or USBIN), VBAT is the battery voltage and IBAT is the charge current. The approximate ambient temperature at which the thermal feedback begins to protect the IC is: It is important to remember that LTC4075 applications do not need to be designed for worst-case thermal conditions, since the IC will automatically reduce power dissipation when the junction temperature reaches approximately 105C. TA = 105C - PD * JA Thermal Considerations TA = 105C - (VIN - VBAT) * IBAT * JA In order to deliver maximum charge current under all conditions, it is critical that the exposed metal pad on the backside of the LTC4075 package is properly soldered to the PC board ground. When correctly soldered to a 2500mm2 double sided 1oz copper board, the LTC4075 has a thermal resistance of approximately 40C/W. Failure to make thermal contact between the exposed pad on the backside of the package and the copper board will result in thermal resistances far greater than 40C/W. As an example, a correctly soldered LTC4075 can deliver over 800mA to a battery from a 5V supply at room temperature. Without a good backside thermal connection, this number would drop to much less than 500mA. Example: An LTC4075 operating from a 5V wall adapter (on the DCIN input) is programmed to supply 800mA full-scale current to a discharged Li-Ion battery with a voltage of 3.3V. Assuming JA is 40C/W (see Thermal Considerations), the ambient temperature at which the LTC4075 will begin to reduce the charge current is approximately: TA = 105C - (5V - 3.3V) * (800mA) * 40C/W TA = 105C - 1.36W * 40C/W = 105C - 54.4C TA = 50.6C The LTC4075 can be used above 50.6C ambient, but the charge current will be reduced from 800mA. The approximate current at a given ambient temperature can be approximated by: 105C - TA IBAT = (VIN - VBAT ) * JA Using the previous example with an ambient temperature of 60C, the charge current will be reduced to approximately: 105C - 60C 45C = (5V - 3.3V)* 40C / W 68C / A = 662mA IBAT = IBAT Protecting the USB Pin and Wall Adapter Input from Overvoltage Transients Caution must be exercised when using ceramic capacitors to bypass the USBIN pin or the wall adapter inputs. High voltage transients can be generated when the USB or wall adapter is hot plugged. When power is supplied via the USB bus or wall adapter, the cable inductance along with the self resonant and high Q characteristics of ceramic capacitors can cause substantial ringing which could exceed the maximum voltage pin ratings and damage the LTC4075. Refer to Linear Technology Application Note 88, entitled "Ceramic Input Capacitors Can Cause Overvoltage Transients" for a detailed discussion of this problem. The long cable lengths of most wall adapters and USB cables 4075Xfa 13 LTC4075/LTC4075X U W U U APPLICATIO S I FOR ATIO makes them especially susceptible to this problem. To bypass the USB pin and the wall adapter input, add a 1 resistor in series with a ceramic capacitor to lower the effective Q of the network and greatly reduce the ringing. A tantalum, OS-CON, or electrolytic capacitor can be used in place of the ceramic and resistor, as their higher ESR reduces the Q, thus reducing the voltage ringing. The oscilloscope photograph in Figure 4 shows how serious the overvoltage transient can be for the USB and wall adapter inputs. For both traces, a 5V supply is hot-plugged using a three foot long cable. For the top trace, only a 4.7F capacitor (without the recommended 1 series resistor) is used to locally bypass the input. This trace shows excessive ringing when the 5V cable is inserted, with the overvoltage spike reaching 10V. For the bottom trace, a 1 resistor is added in series with the 4.7F capacitor to locally bypass the 5V input. This trace shows the clean response resulting from the addition of the 1 resistor. Even with the additional 1 resistor, bad design techniques and poor board layout can often make the overvoltage problem even worse. System designers often add extra inductance in series with input lines in an attempt to minimize the noise fed back to those inputs by the application. In reality, adding these extra inductances only makes the overvoltage transients worse. Since cable inductance is one of the fundamental causes of the excessive ringing, adding a series ferrite bead or inductor increases the effective cable inductance, making the problem even worse. For this reason, do not add additional inductance (ferrite beads or inductors) in series with the USB or wall adapter inputs. For the most robust solution, 6V transorbs or zener diodes may also be added to further protect the USB and wall adapter inputs. Two possible protection devices are the SM2T from STMicroelectronics and the EDZ series devices from ROHM. Always use an oscilloscope to check the voltage waveforms at the USBIN and DCIN pins during USB and wall adapter hot-plug events to ensure that overvoltage transients have been adequately removed. Reverse Polarity Input Voltage Protection In some applications, protection from reverse polarity voltage on the input supply pins is desired. If the supply voltage is high enough, a series blocking diode can be used. In other cases where the voltage drop must be kept low, a P-channel MOSFET can be used (as shown in Figure 5). 4.7F ONLY 2V/DIV DRAIN-BULK DIODE OF FET 4.7F + 1 2V/DIV WALL ADAPTER LTC4075 DCIN 4075 F05 20s/DIV 3455 F04 Figure 4. Waveforms Resulting from Hot-Plugging a 5V Input Supply Figure 5. Low Loss Input Reverse Polarity Protection 4075Xfa 14 LTC4075/LTC4075X U PACKAGE DESCRIPTIO DD Package 10-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1699) R = 0.115 TYP 0.38 0.10 6 10 5 1 0.675 0.05 3.50 0.05 1.65 0.05 2.15 0.05 (2 SIDES) 3.00 0.10 (4 SIDES) PACKAGE OUTLINE 0.25 0.05 PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF 0.50 BSC 2.38 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS 1.65 0.10 (2 SIDES) (DD10) DFN 1103 0.75 0.05 0.00 - 0.05 0.25 0.05 0.50 BSC 2.38 0.10 (2 SIDES) BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WEED-2). CHECK THE LTC WEBSITE DATA SHEET FOR CURRENT STATUS OF VARIATION ASSIGNMENT 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4075Xfa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 15 LTC4075/LTC4075X U TYPICAL APPLICATIO Full Featured Li-Ion Charger 800mA (WALL) 475mA (USB) LTC4075 WALL ADAPTER USB POWER DCIN BAT USBIN 1F 1k PWR IUSB IDC 2.1k 1% 1k 1F 1.24k 1% + CHRG ITERM GND 1-CELL Li-Ion BATTERY 1k 1% 4075 TA03 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3455 Dual DC/DC Converter with USB Power Management and Li-Ion Battery Charger USB Compatible Monolithic Li-Ion Battery Charger Standalone Linear Li-Ion Battery Charger with Integrated Pass Transistor in ThinSOT USB Power Controller and Battery Charger Efficiency >96%, Accurate USB Current Limiting (500mA/100mA), 4mm x 4mm QFN-24 Package Standalone Charger with Programmable Timer, Up to 1.25A Charge Current Thermal Regulation Prevents Overheating, C/10 Termination, C/10 Indicator, Up to 800mA Charge Current Charges Single-Cell Li-Ion Batteries Directly from USB Port, Thermal Regulation, 4mm x 4mm QFN-16 Package C/10 Charge Termination, Battery Kelvin Sensing, 7% Charge Accuracy 4.2V, 0.35% Float Voltage, Up to 1A Charge Current Seamless Transition Between Input Power Sources: Li-Ion Battery, USB and Wall Adapter, Low-Loss (50) Ideal Diode, 4mm x 4mm QFN-24 Package Charge Current up to 950mA, Thermal Regulation, 3mm x 3mm DFN-8 Package Manages Total Power Between a USB Peripheral and Battery Charger, Ultralow Battery Drain: 1A, ThinSOTTM Package Automatic Switching Between DC Sources, Load Sharing, Replaces ORing Diodes LTC4053 LTC4054/LTC4054X LTC4055 LTC4058/LTC4058X LTC4061 LTC4066 LTC4410 Standalone 950mA Lithium-Ion Charger in DFN Standalone Li-Ion Charger with Thermistor Interface USB Power Controller and Li-Ion Linear Battery Charger with Low-Loss Ideal Diode Standalone Linear Li-Ion Battery Charger with Programmable Termination USB Power Manager and Battery Charger LTC4411/LTC4412 Low Loss PowerPathTM Controller in ThinSOT LTC4068/LTC4068X ThinSOT and PowerPath are trademarks of Linear Technology Corporation 4075Xfa 16 Linear Technology Corporation LT 1105 REV A * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2005