High Sensitivity, High Speed Photocoupler 6N139 Series Features Package Dimensions High current transfer ratio ( CTR : MIN. 500% at IF = 1.6mA ) High speed response ( tPHL : TYP. 0.2 s at RL = 270 ) Instantaneous common mode rejection voltage ( CMH : TYP. 500V/ s ) TTL compatible output Options Available : - Leads with 0.4" (10.16mm) Spacing (M Type) - Lead Bends for Surface Mounting (S Type) - Tape and Reel of Type I for SMD (Add "-TA" Suffix) - Tape and Reel of Type II for SMD (Add "-TA1" Suffix) - VDE 0884 Approvals (Add "-V" Suffix) Y R A N I M I L E R P Applications 1. Interfaces for computer peripherals 2. Electronic calculators, measuring instruments, control equipment 3. Telephone sets 4. Signal transmission between circuits of different potentials and impedances NOTES : 1. Year date code. 2. 2-digit work week. 3. Factory code shall be marked (Z Taiwan, Y Thailand). 4. All dimensions are in millimeters (inches). 5. Tolerance is 0.25mm (.010") unless otherwise noted. 6. Specifications are subject to change without notice. Ordering Information Part Number 6N139 6N139M 6N139S 6N139S-TA 6N139S-TA1 6N139-V 6N139M-V 6N139S-V 6N139STA-V 6N139STA1-V 12-142 Application part number Package 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type 8-pin (tape and reel packaging of type 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type 8-pin (tape and reel packaging of type I) II) I) II) 6N139 6N139 Ratings and Characteristics Absolute Maximum Ratings (Ta=25 Symbol Rating Unit Forward Current IF 20 mA Reverse Voltage VR 5 V Power Dissipation P 35 mW Supply Voltage VCC -0.5~+18 V Output Voltage VO -0.5~+18 V VEBO 0.5 V IO 60 mA Parameter Input Emitter-base Reverse Withstand Voltage (pin 5 to 7) Output Average Output Current PO Power Dissipation 100 mW Y R A N I M I L E R P *1.Isolation Voltage V iso 2,500 Operating Temperature Topr 0~+70 Storage Temperature Tstg -55~+125 Tsol 260 *2.Soldering Temperature ) Vrms *1. AC for 1 minute, R.H. = 40 ~ 60% Isolation voltage shall be measured using the following method. (1) Short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) The isolation voltage tester with zero-cross circuit shall be used. (3) The waveform of applied voltage shall be a sine wave. *2. For 10 seconds Parameter Input Forward Voltage Input Forward Voltage Temperature Coefficient ( Ta = 0 ~ +70 Symbol VF / Input Reverse Voltage BVR Input Capacitance CIN *1 Current Transfer Ratio Logic (0) Output Voltage Min. Typ. VF Ta unless otherwise specified ) Max. unit 1.7 V -1.9 mV/ 5.0 V Ta=25 pF 400 1800 % 500 1600 % VF=0, f=1MHz IF=0.5mA, VO=0.4V VCC=4.5V IF=1.6mA, VO=0.4V VCC=4.5V IF=1.6mA VCC=4.5V IO=6.4mA IF=5mA VCC=4.5V IO=15mA IF=12mA VCC=4.5V IO=24mA IF=0, VCC=VO=18V 0.1 0.4 V 0.1 0.4 V 0.1 0.4 V Logic (1) Output Current IOH 0.05 100 A Logic (0) Supply Current I CCL 0.5 1.5 mA Logic (1) Supply Current I CCH 0.01 10 A 1.0 A *2 Leak Current (Input-Output) II-O *2 Isolation Resistance (Input-Output) RI-O 1012 CI-O 0.6 Capacitance (Input-Output) , IF=1.6mA IF=1.6mA 60 CTR VOL Conditions Ta=25 pF , IR=10 A PHOTOCOUPLER Electrical / Optical Characteristics IF=1.6mA, VCC=5V VO=open IF=0, VCC=5V VO=open Ta=25 , 45%RH, t=5s, VI-O=3kV DC VI-O=500VDC f=1MHz *1. Current transfer ratio is the ratio of input current and output current expressed in %. *2. Measured as 2-pin element ( Short 1, 2, 3, 4 and 5, 6, 7, 8 ) 12-143 Electrical / Optical Characteristics Parameter Propagation Delay time Output (1) Propagation Delay time Output (0) Symbol (0) (1) *3 Instantaneous common mode rejection voltage output(1) *3 Instantaneous common mode rejection voltage output(0) ( Ta = 25 Min. Typ. Max. Unit 5 25 s 0.5 1 s 10 60 s 1.5 7 s t PHL t PLH CMH 500 V/ s CML -500 V/ s VCC = 5V) Conditions IF=0.5mA, RL=4.7k IF=12mA, RL=270 IF=0.5mA, RL=4.7k IF=12mA, RL=270 IF=0, VCM=10VP-P1 RL=2.2k VCM=10VP-P, IF=1.6mA RL=2.2k *3 Instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation that can hold the output above (1) level (Vo>2.0V). Instantaneous common mode rejection voltage "output (0)" represents a common mode voltage variation that can hold the output above (0) level (Vo<0.8V). Y R A N I M I L E R P 12-144 Y R A N I M I L E R P PHOTOCOUPLER Typical Electrical/Optical Characteristic Curves (25 Ambient Temperature Unless Otherwise Noted) 12-145 Y R A N I M I L E R P 12-146